Carrier 42PHQ024P Installation manual

Carrier 42PHQ024P Installation manual
R QUALIT
TE
SURANC
E
AS
•
L
INSTALLATION MANUAL
Y
YD'S REGI
S
LO
42PHQ...P
IS O
900 1
For operation and maintenance instructions of this unit, as well as installation
instructions of the outdoor unit, refer to the relevant manuals.
Contents
Page
Dimensions and weight...............................................................................
2
Nominal data ...............................................................................................
2
Operating limits ...........................................................................................
2
Minimum clearances ...................................................................................
3
Material supplied ........................................................................................
3
General information ....................................................................................
4
Warnings: avoid ..........................................................................................
5
Installation ..................................................................................................
6/7
Refrigerant connections .............................................................................
8
Check ..........................................................................................................
9
ENGLISH
42PHQ ...P
Split system “Hi-Wall” indoor unit
Electrical connection .................................................................................. 10/12
Operating test, address selector and fault code ......................................... 13/14
Guide for the owner ....................................................................................
AC/HP models
(R410A)
14
Power supply
42PHQ007P
42PHQ009P
42PHQ012P
230V ~ 50Hz
42PHQ014P
42PHQ018P
42PHQ024P
AC Cooling only
HP Heat pump
GB - 1
42PHQ ...P
Dimensions and weight
Mod.
007
009, 012, 014
018, 024
A
mm
790
790
1080
B
mm
260
260
295
C
mm
186
186
185
8
8.6
14
kg
Table I: Nominal data
ELECTRIC POWER INPUT
• Unit is not suitable for operation in laundry premises.
Cooling only unit
Cooling
W
Heating
W
007
32
-
009
43
-
012
43
-
014
43
-
018
53
-
024
53
-
• For sizing of power supply wires and delay type fuses,
refer to the outdoor unit installation instructions.
Heat pump
007
32
32
009
43
43
012
43
43
014
43
43
018
53
53
024
53
53
Table II: Operating limits
Cooling/Heating
Refer to outdoor unit installation manual.
Mains power supply
Nominal single-phase voltage
Operating voltage limits
GB - 2
230V ~ 50Hz
min. 198V – max. 264V
42PHQ ...P
Minimum clearances (mm)
ENGLISH
90
min.
200
min.
100
min.
1900
min.
Obstacle
Table lIl: Material supplied
The following installation accessories are supplied with unit. Use them as required.
NAME and shape
Q.ty
Use
Wall hanging bracket
1
For indoor unit installation.
Screws 4xL10
2
For fixing unit and hanging bracket
Screws anchors and screws 6xL25
4+4+4
For wall hanging bracket installation.
Washers Ø 12
Screws anchors and screws 6xL20
2+2
Cordless remote control
mounting bracket
1
For cordless remote control mounting bracket installation
For cordless remote control installation.
The following field-supplied items are required to complete the installation.
Name
Connection pipe
Specification
007, 009 :
Ø (3/8”) 9.52 mm (Gas) / Ø (1/4”) 6.35 mm (Liquid)
012, 014, 018, 024 :
Ø (1/2”) 12.70 mm (Gas) / Ø (1/4”) 6.35 mm (Liquid)
Wall sleeve
Wall cap
Finishing tape
Fastening tape
Pipe insulation
Drain hose
Sealer putty
- Power supply cable
H07RN-F or higher
- Electrical connecting cable
between indoor and outdoor unit
Cable type: A07 RN-F, synthetic rubber insulation with Neoprene coating,
according to EN (IEC) 60335-2-40 and HD277.S1 standards.
PVC film
I.D. 16-17 mm
GB - 3
42PHQ ...P
General information
Unit installation
Read this instruction manual thoroughly before starting the
installation.
• This unit complies with low-voltage (EEC/73/23) and electromagnetic compatibility (EEC/89/336) directives.
• The manufacturer declines any liability for damage resulting
from modifications or errors in the electrical or refrigerant
connections.
• Failure to observe the installation instructions or use of the
unit under conditions other than those indicated in Table II
(operating limits), will immediately void the unit warranty.
• The installation must be carried out by a qualified installer.
• Failure to observe electric safety codes may cause a fire hazard in
case of short circuits.
• Follow all current national safety code requirements.
In particular ensure that a properly sized and connected ground
wire is in place.
• Inspect equipment for damage due to improper transportation or
handling: file an immediate claim with the shipping company.
Do not install or use damaged units.
• Check that voltage and frequency of the mains power supply are
those required for the unit to be installed; the available power must
be adequate to operate any other possible appliances connected
to the same line.
Also ensure that national safety code requirements have been
followed for the mains supply circuit.
• In case of any malfunctioning turn the unit off, disconnect the
mains power supply and contact a qualified service engineer.
• The mains supply must be connected as follows:
sizes 007 - 009 - 012 - 014: to the indoor unit;
sizes 018 - 024: to the outdoor unit.
• Connect indoor and outdoor units with field-supplied copper
pipes by means of flare connections. Use insulated seamless
refrigeration grade pipe only, (Cu DHP type according to
ISO1337), degreased and deoxidized, suitable for operating
pressures of at least 4200 kPa and for burst pressure of at least
20700 kPa.
Under no circumstances must sanitary type copper pipe be
used.
• Maintenance of the refrigerant circuit must only be carried out by
qualified personnel.
• All of the manufacturing and packaging materials used for
your new appliance are compatible with the environment and
can be recycled.
• Dispose of the packaging material in accordance with local
requirements.
• This equipment contains refrigerant that must be disposed of in
the proper manner.
When disposing of the unit after its operational life, remove it
carefully.
The unit must then be delivered to an appropriate disposal centre
or to the original equipment dealer for proper environmentally
compatible disposal.
• Where necessary, use field-supplied 16 -17 mm I.D. PVC pipe of
appropriate length and with the correct thermal insulation for the
condensate drain extension.
• After the installation thoroughly test system operation and explain
all system functions to the owner.
• Leave this manual with the owner for consultation during future
periodic maintenance.
• Use this unit only for factory approved applications: the unit
cannot be used in laundry or steam pressing premises.
Choosing the installation site
Positions to avoid:
• Exposed to direct sun.
• Too close to heat sources.
IMPORTANT:
During the unit installation make first refrigerant connections
and then electrical connections. If unit is uninstalled first
disconnect electrical cables, then refrigerant connections.
• On humid walls or positions with water hazard, e.g. laundry premises.
WARNING:
Disconnect the mains power supply switch before servicing
the system or handling any internal parts of the unit.
Recommendations:
• Do not open the remote control to avoid possible damage.
In case of malfunctioning contact a qualified service engineer.
• Check that the wall surface is flat enough to allow easy and safe
installation.
The wall structure should be strong enough to carry the unit
weight and avoid deformation, rupture or vibration during
operation.
• Control batteries contain polluting elements.
When exhausted they must be disposed of according to local
requirements.
• Where curtains or furniture may obstruct free air circulation.
• Choose an area free from obstructions which may cause irregular
air distribution and/or return.
• Consider using an area where installation is easy.
• This installation manual describes the installation procedures of
the indoor unit of a residential split system consisting of two units
manufactured by Carrier.
Consult the factory or a qualified system engineer prior to
connecting this unit to any other manufacturer's outdoor unit.
Coupling units which have different control systems, may cause
irreversible damage and void the warranty protection.
The manufacturer declines any liability for system malfunction
resulting from unapproved coupling.
GB - 4
• Choose a position that allows for the clearances required
(see drawing).
• Look for a position in the room which assures the best possible air
distribution.
• Install unit in a position where condensate can easily be piped to
an appropriate drain.
42PHQ ...P
Warnings: avoid…
Any obstruction of the unit air outlet or return.
Exposure to direct sunshine, when unit is operating in cooling
mode; always use shutters or shades.
Positions too close to heating sources which may damage the unit.
Exposure to oil vapours.
Connecting condensate piping to sewage system drain without
appropriate trap. Trap height must be calculated according to the unit
discharge head in order to allow sufficient and continuous water evacuation.
Installation in areas with high-frequency waves.
Only partial insulation of the piping.
Installation not correctly leveled which will cause condensate dripping.
Any rise in the condensate drain piping.
Horizontal condensate drain piping with less than 2% slope.
Flattening or kinking the refrigerant pipes or condensate pipes.
Excessive height difference between outdoor and indoor units
(see installation manual of outdoor unit).
Slack on electrical connections. Disconnecting refrigerant
connections after installation: this will cause refrigerant leaks.
Unnecessary turns and bends in interconnecting tubing. Excessive
interconnecting tube length (see installation manual of outdoor unit).
GB - 5
42PHQ ...P
Installation
• The piping can be connected in the four ways indicated by ,
, and .
When the piping is connected to points , or , remove
the knock-out either at the side or at the bottom of the unit.
Rear piping
• It is best for the piping to go through the wall behind the unit, so
that the unit hides the pipes.
• For this method of installation, make a 65 mm diameter hole in the
wall at point A.
Marking the wall penetration for the
connection piping
450
23
110
180
260
56
51
40
245
007, 009, 012, 014
IMPORTANT NOTE:
This unit has no refrigerant expansion device.
Installing the wall hanging bracket
899
379
350
155
A
018, 024
450
min.
Plumb line
196
53
120 min.
90
71
53
71
25
• Install the wall hanging bracket so that it is level. Use a plumb
line if necessary.
• Be sure to leave the clearance spaces. (Refer to page 3).
• If the wall hanging bracket is not level, water may drip onto the
floor.
• Install the wall hanging bracket with a fixing that is strong enough
to withstand the weight of the unit.
300
min.
110
• Drill a 65 mm diameter hole at a slope so that the outside end is
lower (5 - 10 mm) than the inside end.
This will ensure good drainage.
• Cut the wall sleeve to match the wall thickness and pass the pipe
through the hole.
• Before installing the wall hanging bracket, remove it from the unit
by pushing at the indicated parts at the bottom of the body.
• Fasten the wall hanging bracket to the wall with 4 or more screw
anchors through the holes near the outer edge of the bracket.
• Install the wall hanging bracket so that there is no gap between
the bracket and the wall.
• Check that the wall hanging bracket does not move.
This can cause noise during operation.
• If the unit is removed from the wall hanging bracket after installing
it onto the wall, remove it by pushing up the indicated MARKS
) at the bottom of the body. (Refer to page 7).
(
GB - 6
Remove screw
Indoor side
Outdoor side
5 ~ 10 mm lower
Side or bottom piping
• Remove the knock-out in the unit and pass the pipes through
the wall.
• The pipe should slope downward and away from the unit to
ensure good drainage.
42PHQ ...P
Installation
Routing the drain hose and refrigerant
piping
• Tie together the refrigerant pipe, the drain hose, and the
electrical connection cord.
• Route the refrigerant piping in the required direction, and bind
the drain hose and the electrical connection cord together with
fastening tape.
The drain hose should be at the bottom.
Wall hanging
bracket
Hook
Hole
Indoor unit
piping
Left-hand piping
Bind with
fastening tape
Drain hose
• For left-hand piping, fit the pipes and the wiring into the recess at
the back of the unit.
[mm]
Model
A
B
007, 009
300
220
012, 014
300
220
018, 024
270
195
Indoor unit piping
Drain hose
Connection cord
NOTE:
• Do not crush or kink the indoor piping. Avoid sharp bends with a
bend radius of less than 100 mm.
• Do not bend the same part of the pipe too often.
• Do not remove the flare nut from the indoor unit pipe until the
piping is connected.
• The recommended bending of the drain hose is shown.
Installing the indoor unit body to the wall
hanging bracket
• Pass the pipes through the wall sleeve and then hook the
indoor unit body on top of the wall hanging bracket.
• For left-hand piping, hang the unit on top of the wall hanging
bracket and incline the unit using a tool such as a screwdriver
set between the middle area of the body and bottom right of
the wall hanging bracket.
Connecting the pipe can be done more easily if the unit is
inclined.
• Fix the bottom part of the unit to the wall hanging bracket, by
pushing it carefully unit the two bracket hooks fit into the
marked places at the base of the unit (a click will be heard).
GB - 7
42PHQ ...P
Refrigerant connections
Refer to the outdoor unit installation manual for tube sizing,
and limitations (slope, length, number of bends allowed,
refrigerant charge, etc.).
Tubing diameter
Gas
Liquid
(Suction)
(Discharge)
mm
(inches)
mm
(inches)
Model
007, 009
9.52
012, 014, 018, 024
12.70
(3/8")
(1/2")
6.35
6.35
(1/4")
(1/4")
For refrigerant tubes use seamless, insulated refrigeration grade
tube, (Cu DHP type according to ISO1337), degreased and
deoxidized, suitable for operating pressures of at least 4200 kPa
and for burst pressure of at least 20700 kPa.
Under no circumstances must sanitary type copper pipe be used.
Flaring the end of the tubing
Lubricate the tube end and thread of the flare fitting with antifreeze oil.
Finger-tighten the fitting several turns, then tighten it fully with
two wrenches by applying the tightening torque indicated in the
table.
Connection to the unit
Insufficient tightening torque will cause gas leaks.
Overtightening the fittings will damage the tube flaring and
cause gas leaks.
1
3
Adjustable wrench or torque wrench
Outdoor end
Indoor end
Remove protective caps from the copper tube ends.
Position tube end downward, cut the tube to the required length
and remove the burrs with a reamer.
2
Tubing diameter
mm (inches)
Torque
Nm
6.35
(1/4")
18
9.52
(3/8")
42
12.70
(1/2")
55
5
4
Remove flare nuts from the unit connections and place them on
the tube end.
Flare the tube with the flaring tool.
Tube
Tube insulation
Fastening tape
L
L
Flare end must not have any burrs or imperfections.
The length of the flared walls must be uniform.
GB - 8
6
Once all connections have been completed, check for leaks by
applying soapy water to them.
Finally wrap connections with anti-condensate insulation and
tighten with tape, without exerting great pressure on the
insulation.
Repair and cover any possible cracks in the insulation.
Connection pipes and electric cables between indoor and
outdoor units must be fixed to the wall with appropriate
conduits.
42PHQ ...P
Check
300 mm
min.
• Next, check the unit drain system by pouring some water into
the unit drain pan and ensuring that it flows freely through the
drain hose and that there is no leakage from any other part.
Remote control
bracket
Use of additional screws
Installing the remote control bracket
After installation, if there is a significant gap between the unit and
wall, it can be adjusted by securing the body to the wall hanging
bracket using 2 screws. Screw holes can be only seen after
removing the frame grille.
• Fix the bracket onto the wall using double sided adhesive tape or
2 screws.
• Install the batteries in the remote control and position it in the
bracket.
Grille
Front panel
GB - 9
42PHQ ...P
Electrical connection
IMPORTANT:
• Make refrigerant connections before electrical
connections.
When disconnecting, disconnect electrical connections before
refrigerant connections.
• For sizes 007 - 009 - 012 - 014 make ground connection
prior to any other electrical connections.
• The mains supply must be connected as follows:
sizes 007 - 009 - 012 - 014: to the indoor unit.
sizes 018 - 024 : to the outdoor unit.
• Make electrical connections between units prior to proceeding
to mains supply unit connection.
• Before proceeding with the connection to the mains supply
locate live L and neutral N, then make connections as shown
in the wiring diagram.
• Ensure that mains supply connection is made through a switch
that disconnects all poles, with contact gap of a least 3 mm.
• The indoor - outdoor unit connecting wires must be A07 RN-F
type (or higher), with synthetic rubber insulation with Neoprene
coating, according to EN 60335-2-40 and HD277.S1 codes.
• The mains supply connecting cable must be H07 RN-F type (or
higher), with synthetic rubber insulation with neoprene coating,
according to EN 60335-2-40 and HD277.S1 codes.
• Ground connection between indoor and outdoor units is made
via the refrigerant pipes.
Notes:
All field electrical connections are the responsibility of the
installer.
GB - 10
Indoor unit wiring
• Lift the front panel up to the top of the unit; in this way the
front panel will be separated from the unit.
• Remove the plastic cover of the terminal board.
• Make the electrical connections to the terminal board as per
the wiring diagram.
• When the electrical connections are completed, refit the
terminal board cover and fix the cables with the special cable
holders.
• Fix the front panel to the latch of the frame grille.
42PHQ ...P
Electrical connection
ENGLISH
Cooling only
42PHQ007P, 009P, 012P, 014P
1
Note :
Refer also to outdoor units
installation manual
3
Minimum connection wire size
for power supply (mm2)
Minimum connection wire size between
indoor and outdoor unit (mm2)
Models
GND
L
N
N
Y
O
W2
42PHQ007P, 009P
1.5
1.5
1.5
1.5
1.5
—
—
42PHQ012P, 014P
2.5
2.5
2.5
2.5
2.5
—
—
Note :
Refer also to outdoor units
installation manual
2
Minimum connection wire size
for power supply (mm2)
Minimum connection wire size between
indoor and outdoor unit (mm2)
Models
GND
L
N
N
Y
O
W2
42PHQ007P, 009P
—
1.5
1.5
—
1.5
—
—
42PHQ012P, 014P
—
2.5
2.5
—
2.5
—
—
Terminal box legend, all models
Earth
L Live power supply
N Neutral power supply
N Neutral connection indoor/outdoor unit
R Live connection indoor/outdoor unit.
C Neutral connection indoor/outdoor unit.
Y Compressor interlocking contact.
O Reversing valve control
W2 Outdoor fan signal
S Defrost end signal
10
120
10 100
Power supply cable (H07 RN-F)
Interconnecting cable (A07 RN-F)
Interconnecting cable (H07 RN-F)
GB - 11
42PHQ ...P
Electrical connection
Heat pump
42PHQ007P, 009P, 012P, 014P
1
Note :
Refer also to outdoor units
installation manual
3
Minimum connection wire size
for power supply (mm2)
Models
GND
L
N
N
Y
O
W2
42PHQ007P, 009P
1.5
1.5
1.5
1.5
1.5
1.5
1.5
42PHQ012P, 014P
2.5
2.5
2.5
2.5
2.5
2.5
2.5
3
Note :
Refer also to outdoor units
installation manual
2
Minimum connection wire size
for power supply (mm2)
Minimum connection wire size between
indoor and outdoor unit (mm2)
Models
GND
L
N
N
Y
O
W2
42PHQ007P, 009P
—
1.5
1.5
—
1.5
1.5
1.5
42PHQ012P, 014P
—
2.5
2.5
—
2.5
2.5
2.5
Terminal box legend, all models
Earth
L Live power supply
N Neutral power supply
N Neutral connection indoor/outdoor unit
R Live connection indoor/outdoor unit.
C Neutral connection indoor/outdoor unit.
Y Compressor interlocking contact.
O Reversing valve control
W2 Outdoor fan signal
S Defrost end signal
GB - 12
Minimum connection wire size between
indoor and outdoor unit (mm2)
10
120
10 100
Power supply cable (H07 RN-F)
Interconnecting cable (A07 RN-F)
Interconnecting cable (H07 RN-F)
42PHQ ...P
Operating test and address selector
ENGLISH
NOTE:
• Indoor fan speed will be "HIGH" in Test operation.
• The swing motor will operate when the indoor fan is operated.
• Operate the unit in accordance with the Owner's Manual and
check the following:
a. Indoor unit.
- Do all switches operate normally?
- Does each light come on normally?
- Do the horizontal louvres operate normally?
- Is the drain correct?
b. Outdoor unit.
- Is there any abnormal noise or vibration during operation?
- Is there any gas leakage?
EMER.
B
Adress switch
A
018, 024
Address selector
If you are installing two indoor units in the same room, it is
necessary for you to assign each unit its own address so each can
be operated by its own remote controller.
One address selector is in the PCB side and the other is
configured by remote controller.
The address selector is set to A when yoy purchase the unit.
• Indoor unit
- Turn off the unit and pull out the power plug.
- Remove the front panel and terminal block cover.
- Assign the address selector of one indoor unit to B.
B
Jumper cap
A
007, 009, 012, 014
Configuration (of the remote controller)
Operating test
This procedure is used to check the operation after unit installation.
• Press the EMER. button continuously for 5~10 seconds.
The unit will now be in Test Mode.
• Press the EMER. button once more after checking, to activate
the remote control. If there is any input signal (remote control
signal or EMER. button press) during test operation, the TEST
mode will change to the input signal mode.
• The setting conditions of the test operation are as follows:
1) Mono type
- Operating mode: COOL
- Fan speed: HIGH
- Timer mode: Disabled
- Discharge air direction: SWING
2) Multi or T-kit type
- Operation LED: ON
- Timer LED : Blink ON for 0.5 seconds and OFF for 0.5 seconds
four (for T-kit model) and three times(for multi model)
- Operation mode :
Cool mode for 3 minutes, firstly and then Heat mode for
2 minutes and Cool mode until test mode is existed
- Fan speed: HIGH
- Timer mode: Disabled
- Discharge air direction: SWING
• Press the
and
buttons of the infrared remote controller and
hold them pressed for more than 5 seconds.
• The display will be cleared, the temperature segments will
display the first configuration item (CH = remote address) and
the time segments will display the default value of this
configuration item (A = control of both indoor units).
or
button to change the default value (A)
• Press either the
to the new value (b).
button repeatedly until “tU” is displayed.
• Press
or
button to change the default value of
• Press either the
temperatures in Degrees Celsius (C) to the new value Degrees
Fahrenheit (oF).
button repeatedly until “rc” is displayed.
• Press
or
button to change the default value of
• Press either the
Heat pump in model type (HP) to new value cooling only Export
(CO1) or cooling only korean (CO2).
button repeatedly until “CL” is displayed.
• Press
• Press either the
or
button to change the default value of
time format as AM/PM (12) to the new value of 24 hours time
format (24).
• LOOK OUT! Whichever configuration value changed must be
button each time.
confirmed pressing
button to leave the configuration menu.
• Press
Note:
When 30 seconds have elapsed and no buttons have been
pressed, the remote controller will automatically exit the
configuration menu and the procedure has to be restarted.
GB - 13
42PHQ ...P
Operating test, fault code and guide for the owner
Table VI: Remote configuration
Configuration (of the unit)
• Press the
and
buttons of the infrared remote controller
and hold them pressed for more than 5 seconds.
• The display will be cleared, the time segments will display the
configuration item.
button repeatedly until “UCFG” is displayed.
• Press
or
button to change the default value of
• Press either
Heat pump in model type (HP) to new value cooling only
Export
(1AC) or cooling only Korea ( 2AC)
button repeatedly until “GFDn” is displayed.
• Press
(GFDn = Application select)
Confirguration item
"CH"
"tU"
"rc"
"CL"
Value
Description
A : Channel A
Remote ID selection
b : Channel B
Defaults to A
C : Degrees C
Temperature units
F : Degrees F
Defaults to C
HP : Normal Operation
Puts the Remote into
CO 1 : Cooling Only for Export
Cooling Only Mode
CO 2 : Cooling Only for Korea
Defaults to HP
12 : 12 Hour Standard
Time Format
(AM/PM)
Defaults to 12
24 : 24 Hour Military
or
button to change the default value of
• Press either the
Application number (1) to the new valve (1÷240).
• LOOK OUT! Whichever configuration value changed must
button each time.
be transmitted to the indoor unit
• Press
button to leave the configuration menu.
Guide for the owner
When installation and tests are completed explain the Operation
and Maintenance Manual to the owner, with particular attention
to the main operating modes of the air conditioner, such as:
• Turning the unit on and off.
Fault code
• Functions of the remote controller.
Once a failure occurs with the indoor unit in operation.
the green LED flashes at intervals of 0.5 seconds.
The fault code is deduced from the number of times the green
LED flahes, blocking unit operation.
Between one flash cycle and the next one, a pause of seconds
3 elapses.
Table IV: Fault code
Green LED
Code
Description
1
System selection Fault
2
Room Air Sensor Fault
3
Indoor coil sensor Fault
5
Compressor Drive Fault
6
Reversing valve Fault
9
Power line feedback fault
Continuous
Indoor thermistor wiring reversed
Table V: Unit configuration
Shown on display
"rAdr"
"UCFG"
Explanation
Description
It is not used
It is not used
"HP" : Heat Pump
Unit Configuration
"1AC": AC Only for export
Defaults to Heat Pump
"2AC": AC Only for korean
"GFdn"
1-240 in increments of 1
GFD Number
Defaults to 1,
1-238 : Mono(1x1)
239 : T-kit
240 : Multi
"ArEA"
GB - 14
It is not used
It is not used
• Removal and cleaning of the air filters.
Leave the two installation manuals for the indoor and outdoor
units with the owner for future use during maintenance
operations or for any other needs.
42KU5A54040
Via R. Sanzio, 9 - 20058 Villasanta (MI) Italy - Tel. 039/3636.1
The manufacturer reserves the right to change any product specifications without notice.
December, 2003
Printed in Korea
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement