WAFER-BT-i1_UMN_v1.03
WAFER-BT-i1
WAFER-BT-i1 CPU Card
MODEL:
WAFER-BT-i1
3.5” SBC with Intel® 22nm Atom™/Celeron® on-board SoC,
VGA/LVDS/iDP, Dual PCIe GbE, USB 3.0, PCIe Mini,
SATA 3Gb/s, mSATA, COM, Audio and RoHS
User Manual
Page I
Rev. 1.03 - August 26, 2015
WAFER-BT-i1
Revision
Date
Version
Changes
August 26, 2015
1.03
Updated Figure 1-3: Dimensions (mm)
Updated Section 2: Unpacking
Updated Table 3-17: RS-232 Serial Port Connector Pinouts
Added Section 4.7: Chassis Installation
Added notices for mSATA and SATA2 usage
February 13, 2015
1.02
Updated Section 1.5: Dimensions
January 26, 2015
1.01
Updated Section 3.2.23: USB connectors pinouts
July 7, 2014
1.00
Initial release
Page II
WAFER-BT-i1
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page III
WAFER-BT-i1
Manual Conventions
WARNING
Warnings appear where overlooked details may cause damage to the
equipment or result in personal injury. Warnings should be taken
seriously.
CAUTION
Cautionary messages should be heeded to help reduce the chance of
losing data or damaging the product.
NOTE
These messages inform the reader of essential but non-critical
information. These messages should be read carefully as any directions
or instructions contained therein can help avoid making mistakes.
HOT SURFACE
This symbol indicates a hot surface that should not be touched without
taking care.
Page IV
WAFER-BT-i1
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 INTRODUCTION........................................................................................................... 2
1.2 MODEL VARIATIONS ................................................................................................... 2
1.3 FEATURES ................................................................................................................... 3
1.4 CONNECTORS ............................................................................................................. 3
1.5 DIMENSIONS ............................................................................................................... 4
1.6 DATA FLOW ................................................................................................................ 6
1.7 TECHNICAL SPECIFICATIONS ...................................................................................... 7
2 UNPACKING ............................................................................................................... 10
2.1 ANTI-STATIC PRECAUTIONS .......................................................................................11
2.2 UNPACKING PRECAUTIONS ........................................................................................11
2.3 PACKING LIST........................................................................................................... 12
2.4 OPTIONAL ITEMS ...................................................................................................... 13
3 CONNECTORS ........................................................................................................... 14
3.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 15
3.1.1 WAFER-BT-i1 Layout....................................................................................... 15
3.1.2 Peripheral Interface Connectors ..................................................................... 15
3.1.3 External Interface Panel Connectors............................................................... 17
3.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 17
3.2.1 +12V DC-IN Power Connector ....................................................................... 17
3.2.2 Audio Connector .............................................................................................. 18
3.2.3 Battery Connector............................................................................................ 19
3.2.4 Buzzer Connector............................................................................................. 20
3.2.5 CPU Fan Connector ........................................................................................ 21
3.2.6 DDR3L SO-DIMM Slot.................................................................................... 21
3.2.7 Digital I/O Connector ...................................................................................... 22
3.2.8 Display Port Connector ................................................................................... 23
3.2.9 Front Panel Connector .................................................................................... 24
3.2.10 iRIS-1010 module slot.................................................................................... 25
Page V
WAFER-BT-i1
3.2.11 Keyboard and Mouse Connector.................................................................... 26
3.2.12 LVDS Backlight Inverter Connector .............................................................. 26
3.2.13 LVDS LCD Connector ................................................................................... 27
3.2.14 LAN LED Connector...................................................................................... 29
3.2.15 PCIe Mini Card Slot ...................................................................................... 29
3.2.16 Power Button Connector................................................................................ 30
3.2.17 Reset Button Connector ................................................................................. 31
3.2.18 RS-232 Serial Port Connectors...................................................................... 32
3.2.19 RS-422/485 Serial Port Connector ................................................................ 33
3.2.20 SATA 3Gb/s Drive Connectors....................................................................... 34
3.2.21 SATA Power Connectors ................................................................................ 35
3.2.22 SMBUS Connector ......................................................................................... 36
3.2.23 USB Connectors............................................................................................. 36
3.3 EXTERNAL PERIPHERAL INTERFACE CONNECTOR PANEL ......................................... 37
3.3.1 LAN Connector ................................................................................................ 38
3.3.2 USB Connectors............................................................................................... 39
3.3.3 RS-232 Serial Port Connector ......................................................................... 39
3.3.4 VGA Connector ................................................................................................ 40
4 INSTALLATION ......................................................................................................... 42
4.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 43
4.2 INSTALLATION CONSIDERATIONS .............................................................................. 43
4.3 SO-DIMM INSTALLATION ....................................................................................... 45
4.4 FULL-SIZE PCIE MINI CARD INSTALLATION ............................................................. 46
4.5 HALF-SIZE PCIE MINI CARD INSTALLATION............................................................. 49
4.6 SYSTEM CONFIGURATION ......................................................................................... 51
4.6.1 AT/ATX Mode Select Switch............................................................................. 51
4.6.2 Clear CMOS Button......................................................................................... 52
4.6.3 LVDS Panel Resolution Selection .................................................................... 52
4.6.4 LVDS Voltage Selection.................................................................................... 54
4.6.5 Flash Descriptor Security Override Jumper.................................................... 55
4.7 CHASSIS INSTALLATION ............................................................................................ 56
4.7.1 Heat Sink Enclosure......................................................................................... 56
4.7.2 Motherboard Installation................................................................................. 57
4.8 INTERNAL PERIPHERAL DEVICE CONNECTIONS ........................................................ 58
Page VI
WAFER-BT-i1
4.8.1 Audio Kit Installation....................................................................................... 58
4.8.2 SATA Drive Connection ................................................................................... 59
4.8.3 Single RS-232 Cable ........................................................................................ 60
5 BIOS .............................................................................................................................. 61
5.1 INTRODUCTION......................................................................................................... 62
5.1.1 Starting Setup................................................................................................... 62
5.1.2 Using Setup ...................................................................................................... 62
5.1.3 Getting Help..................................................................................................... 63
5.1.4 Unable to Reboot after Configuration Changes .............................................. 63
5.1.5 BIOS Menu Bar................................................................................................ 63
5.2 MAIN........................................................................................................................ 64
5.3 ADVANCED ............................................................................................................... 65
5.3.1 ACPI Settings ................................................................................................... 66
5.3.2 Super IO Configuration ................................................................................... 67
5.3.2.1 Serial Port n Configuration ....................................................................... 67
5.3.2.1.1 Serial Port 1 Configuration ................................................................ 68
5.3.2.1.2 Serial Port 2 Configuration ................................................................ 68
5.3.2.1.3 Serial Port 3 Configuration ................................................................ 69
5.3.2.1.4 Serial Port 4 Configuration ................................................................ 70
5.3.3 Hardware Monitor ........................................................................................... 71
5.3.3.1 Smart Fan Mode Configuration ................................................................ 72
5.3.4 RTC Wake Settings ........................................................................................... 75
5.3.5 Serial Port Console Redirection ...................................................................... 76
5.3.5.1 Console Redirection Settings.................................................................... 77
5.3.6 CPU Configuration.......................................................................................... 80
5.3.7 IDE Configuration ........................................................................................... 81
5.3.8 USB Configuration........................................................................................... 82
5.4 CHIPSET ................................................................................................................... 83
5.4.1 North Bridge Configuration............................................................................. 84
5.4.1.1 Intel IGD Configuration............................................................................ 85
5.4.2 Southbridge Configuration .............................................................................. 86
5.4.2.1 PCI Express Configuration ....................................................................... 88
5.5 SECURITY ................................................................................................................. 89
5.6 BOOT........................................................................................................................ 90
Page VII
WAFER-BT-i1
5.7 EXIT ......................................................................................................................... 92
A REGULATORY COMPLIANCE .............................................................................. 94
B BIOS MENU OPTIONS ............................................................................................. 96
C TERMINOLOGY ....................................................................................................... 99
D DIGITAL I/O INTERFACE..................................................................................... 104
D.1 INTRODUCTION ...................................................................................................... 105
D.2 ASSEMBLY LANGUAGE SAMPLE 1.......................................................................... 106
D.3 ASSEMBLY LANGUAGE SAMPLE 2.......................................................................... 106
E WATCHDOG TIMER............................................................................................... 107
F HAZARDOUS MATERIALS DISCLOSURE.........................................................110
F.1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS ROHS
COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY .................................................111
Page VIII
WAFER-BT-i1
List of Figures
Figure 1-1: WAFER-BT-i1 ...............................................................................................................2
Figure 1-2: Connectors ..................................................................................................................3
Figure 1-3: Dimensions (mm) ........................................................................................................5
Figure 1-4: Data Flow Diagram......................................................................................................6
Figure 3-1: Connector and Jumper Locations (Front) ..............................................................15
Figure 3-2: +12V DC-IN Power Connector Location..................................................................18
Figure 3-3: Audio Connector Location .......................................................................................19
Figure 3-4: Battery Connector Location.....................................................................................20
Figure 3-5: Buzzer Connector Location .....................................................................................20
Figure 3-6: CPU Fan Connector Locations ................................................................................21
Figure 3-7: DDR3L SO-DIMM Slot Location ...............................................................................22
Figure 3-8: Digital I/O Connector Location ................................................................................22
Figure 3-9: Display Port Connector Location ............................................................................23
Figure 3-10: Front Panel Connector Location ...........................................................................24
Figure 3-11: iRIS-1010 Module Slot Location ............................................................................25
Figure 3-12: Keyboard and Mouse Location..............................................................................26
Figure 3-13: Backlight Inverter Connector Location.................................................................27
Figure 3-14: LVDS Connector Location......................................................................................28
Figure 3-15: LAN LED Connector Location ...............................................................................29
Figure 3-16: PCIe Mini Card Slot Location .................................................................................30
Figure 3-17: Power Button Connector Location........................................................................31
Figure 3-18: Reset Button Connector Location.........................................................................32
Figure 3-19: RS-232 Serial Port Connectors Locations............................................................32
Figure 3-20: RS-422/485 Connector Location............................................................................33
Figure 3-21: SATA 3Gb/s Drive Connectors Locations ............................................................34
Figure 3-22: SATA Power Connector Locations .......................................................................35
Figure 3-23: SMBUS Connectors Location ................................................................................36
Figure 3-24: USB Connectors Locations....................................................................................37
Figure 3-25: External Peripheral Interface Connector ..............................................................38
Figure 3-26: LAN Connector........................................................................................................38
Figure 3-27: RS-232 Serial Port Connector................................................................................40
Page IX
WAFER-BT-i1
Figure 3-28: VGA Connector .......................................................................................................40
Figure 4-1: SO-DIMM Installation ................................................................................................45
Figure 4-2: Removing the Retention Screw ...............................................................................46
Figure 4-3: Removing the Retention Screw and Standoff ........................................................47
Figure 4-4: Inserting the Full-size PCIe Mini Card into the Slot at an Angle ..........................47
Figure 4-5: Securing the Full-size PCIe Mini Card ....................................................................48
Figure 4-6: Removing the Retention Screw ...............................................................................49
Figure 4-7: Inserting the Half-size PCIe Mini Card into the Slot at an Angle..........................50
Figure 4-8: Securing the Half-size PCIe Mini Card ....................................................................50
Figure 4-9: AT/ATX Mode Select Switch Location ....................................................................51
Figure 4-10: Clear CMOS Button Location.................................................................................52
Figure 4-11: LVDS Panel Resolution Selection Switch Location ............................................54
Figure 4-12: LVDS Voltage Selection Jumper Location ...........................................................55
Figure 4-13: Flash Descriptor Security Override Jumper Location ........................................56
Figure 4-14: Motherboard Installation Example ........................................................................57
Figure 4-15: Audio Kit Cable Connection ..................................................................................58
Figure 4-16: SATA Drive Cable Connection...............................................................................59
Figure 4-17: Single RS-232 Cable Installation ...........................................................................60
Page X
WAFER-BT-i1
List of Tables
Table 1-1: WAFER-BT-i1 Model Variations ..................................................................................2
Table 1-2: Technical Specifications..............................................................................................9
Table 3-1: Peripheral Interface Connectors ...............................................................................16
Table 3-2: Rear Panel Connectors ..............................................................................................17
Table 3-3: +12V DC-IN Power Connector Pinouts .....................................................................18
Table 3-4: Audio Connector Pinouts ..........................................................................................19
Table 3-5: Battery Connector Pinouts ........................................................................................20
Table 3-6: Buzzer Connector Pinouts.........................................................................................21
Table 3-7: CPU Fan Connector Pinouts......................................................................................21
Table 3-8: Digital I/O Connector Pinouts....................................................................................23
Table 3-9: Display Port Connector Pinouts ...............................................................................24
Table 3-10: Front Panel Connector Pinouts...............................................................................25
Table 3-11: Keyboard and Mouse Connector Pinouts ..............................................................26
Table 3-12: Backlight Inverter Connector Pinouts ....................................................................27
Table 3-13: LVDS Connector Pinouts .........................................................................................28
Table 3-14: LAN LED Connector Pinouts...................................................................................29
Table 3-15: Power Button Connector Pinouts ...........................................................................31
Table 3-16: Reset Button Connector Pinouts ............................................................................32
Table 3-17: RS-232 Serial Port Connector Pinouts ...................................................................33
Table 3-18: RS-422/485 Connector Pinouts ...............................................................................33
Table 3-19: DB-9 RS-422/485 Pinouts .........................................................................................34
Table 3-20: SATA Power Connector Pinouts.............................................................................35
Table 3-21: SMBUS Connectors Pinouts....................................................................................36
Table 3-22: USB Connectors Pinouts .........................................................................................37
Table 3-23: LAN Pinouts ..............................................................................................................38
Table 3-24: Connector LEDs........................................................................................................39
Table 3-25: USB 2.0 Port Pinouts................................................................................................39
Table 3-26: USB 3.0 Port Pinouts................................................................................................39
Table 3-27: RS-232 Serial Port Connector Pinouts ...................................................................40
Table 3-28: VGA Connector Pinouts...........................................................................................41
Table 4-1: AT/ATX Mode Select Switch Settings.......................................................................51
Page XI
WAFER-BT-i1
Table 4-2: Clear CMOS Button Settings .....................................................................................52
Table 4-3: LVDS Panel Resolution Selection.............................................................................53
Table 4-4: LVDS Voltage Selection Jumper Settings................................................................54
Table 4-5: Flash Descriptor Security Override Jumper Settings.............................................55
Table 5-1: BIOS Navigation Keys ................................................................................................63
Page XII
WAFER-BT-i1
List of BIOS Menus
BIOS Menu 1: Main .......................................................................................................................64
BIOS Menu 2: Advanced ..............................................................................................................65
BIOS Menu 3: ACPI Configuration ..............................................................................................66
BIOS Menu 4: Super IO Configuration........................................................................................67
BIOS Menu 5: Serial Port n Configuration Menu.......................................................................67
BIOS Menu 6: Hardware Monitor.................................................................................................72
BIOS Menu 7: Smart Fan Mode Configuration ..........................................................................73
BIOS Menu 8: RTC Wake Settings ..............................................................................................75
BIOS Menu 9: Serial Port Console Redirection .........................................................................77
BIOS Menu 10: Console Redirection Settings...........................................................................78
BIOS Menu 11: CPU Configuration .............................................................................................80
BIOS Menu 12: IDE Configuration...............................................................................................81
BIOS Menu 13: USB Configuration .............................................................................................82
BIOS Menu 14: Chipset ................................................................................................................84
BIOS Menu 15: Northbridge Chipset Configuration..................................................................84
BIOS Menu 16: Integrated Graphics ...........................................................................................85
BIOS Menu 17: Southbridge Chipset Configuration .................................................................87
BIOS Menu 18: Console Redirection Settings...........................................................................88
BIOS Menu 19: Security ...............................................................................................................89
BIOS Menu 20: Boot .....................................................................................................................90
BIOS Menu 21:Exit........................................................................................................................92
Page XIII
WAFER-BT-i1
Chapter
1
1 Introduction
Page 1
WAFER-BT-i1
1.1 Introduction
Figure 1-1: WAFER-BT-i1
The WAFER-BT-i1 SBC motherboard is an Intel® Atom™/Celeron® processor platform. It
supports one 204-pin 1066/1333 MHz single-channel DDR3L SO-DIMM supports up to
8GB (J1900, N2930, E3845, E3827, E3826) or 4GB (N2807, E3825, E3815).
The WAFER-BT-i1 includes a VGA connector, a LVDS connector and an iDP connector.
Expansion and I/O include one USB 2.0 connector and one USB 3.0 connector on the rear
panel, four USB 2.0 connectors by pin header and two SATA 3Gb/s connectors. Serial
device connectivity is provided by two internal RS-232 connectors, one external RS-232
connector and one internal RS-422/485 connector. Two RJ-45 Ethernet connectors
provide the system with smooth connections to an external LAN.
1.2 Model Variations
The model variations of the WAFER-BT-i1 Series are listed below.
Model No.
SoC
WAFER-BT-i1-J19001-R10
Intel® Celeron® quad-core J1900 (10W)
WAFER-BT-i1-N29301-R10
Intel® Celeron® quad-core N2930 (7.5W)
WAFER-BT-i1-N28071-R10
Intel® Celeron® dual-core N2807 (4.3W)
WAFER-BT-i1-E38XX1-R10
Intel® Atom™ E38XX
Table 1-1: WAFER-BT-i1 Model Variations
Page 2
WAFER-BT-i1
1.3 Features
Some of the WAFER-BT-i1 motherboard features are listed below:

3.5" SBC supports Intel® 22nm Atom™/Celeron® on-board SoC

Dual independent display support

One 204-pin 1066/1333 MHz single-channel DDR3L SO-DIMM supports up to
8GB (J1900, N2930, E3845, E3827, E3826) or 4GB (N2807, E3825, E3815)

COM, USB 3.0, SATA 3Gb/s, PCIE mini, mSATA and Audio support

IEI one key recovery solution allows you to create rapid OS backup and
recovery
1.4 Connectors
The connectors on the WAFER-BT-i1 are shown in the figure below.
Figure 1-2: Connectors
Page 3
WAFER-BT-i1
1.5 Dimensions
The dimensions of the board are listed below:
Page 4
WAFER-BT-i1
Figure 1-3: Dimensions (mm)
Page 5
WAFER-BT-i1
1.6 Data Flow
Figure 1-4 shows the data flow between the system chipset, the CPU and other
components installed on the motherboard.
Figure 1-4: Data Flow Diagram
Page 6
WAFER-BT-i1
1.7 Technical Specifications
WAFER-BT-i1 technical specifications are listed below.
Specification
WAFER-BT-i1
SoC
Intel® Atom™ E3845 on-board SoC (1.91GHz, quad-core,
2MB cache, TDP=10W)
Intel® Atom™ E3827 on-board SoC (1.75GHz, dual-core,
1MB cache, TDP=8W)
Intel® Atom™ E3826 on-board SoC (1.46GHz, dual-core,
1MB cache, TDP=7W)
Intel® Atom™ E3825 on-board SoC (1.33GHz, dual-core,
1MB cache, TDP=6W)
Intel® Atom™ E3815 on-board SoC (1.46GHz, single-core,
512KB cache, TDP=5W)
Intel® Celeron® J1900 on-board SoC (2GHz, quad-core,
2MB cache, TDP=10W)
Intel® Celeron® N2930 on-board SoC (1.83GHz, quad-core,
2MB cache, TDP=7.5W)
Intel® Celeron® N2807 on-board SoC (1.58GHz, dual-core,
2MB cache, TDP=4.3W)
BIOS
AMI UEFI BIOS
Memory
One 204-pin 1066/1333 MHz single-channel DDR3L
SO-DIMM supports up to 8GB (J1900, N2930, E3845, E3827,
E3826) or 4GB (N2807, E3825, E3815)
Graphics
Intel® HD Graphics Gen 7 Engines with 4 execution unit,
supports DX11.1, OpenGL 4.2 and OpenCL1.2
Display Output
Dual Independent Display
1 x VGA (Resolution: [email protected])
1 x 24-bit dual-channel LVDS connector ([email protected])
1 x iDP interface for HDMI, LVDS, VGA, DVI, DP (up to
[email protected] Hz)
Page 7
WAFER-BT-i1
Specification
WAFER-BT-i1
Ethernet
1 x PCIe GbE by Intel I210 controller (LAN1)
1 x PCIe GbE by Intel I211 controller (LAN2)
Super IO
Fintek F81866
Embedded Controller
ITE IT8528E
Audio
Realtek ALC662 HD codec
Watchdog Timer
Software programmable support 1~255 sec. system reset
I/O Interface
Audio Connector
1 x Analog audio by 10-pin (2x5) header
Ethernet
Two RJ-45 ports
KB/MS
1 x PS/2 KB/MS
Serial Ports
1 x RS-422/485 (by pin header)
3 x RS-232 (1 on rear I/O, 2 by pin header)
USB Ports
1 x USB 3.0 (on rear I/O)
5 x USB 2.0 (1 on rear I/O, 4 by pin header)
Front Panel
1 x 6-pin (1x6) wafer for power LED & HDD LED
1 x 2-pin (1x2) wafer for power button
1 x 2-pin (1x2) wafer for power reset button
LAN LED
2 x 2-pin header for LAN1 Link LED, LAN2 Link LED
FAN
1 x 4-pin CPU fan connector
1 x 4-pin system fan connector
SMBus
1 x 4-pin (1x4) wafer
Expansion
1 x Full-size/Half-size PCIe Mini card slot with mSATA support
(SATA2 and mSATA share SATA signal)
iRIS Remote Management
1 x iRIS-1010 slot
Module
Digital I/O
Storage
Page 8
8-bit digital I/O (4-bit input, 4-bit output)
WAFER-BT-i1
Specification
WAFER-BT-i1
Serial ATA
2 x SATA 3Gb/s with 5V SATA power connector (no RAID)
Environmental and Power Specifications
Power Supply
12V DC input only (AT/ATX support)
Power Consumption
[email protected] (Intel® Celeron® J1900 CPU, 1 x 8GB 1333
MHz DDR3 memory)
Operating Temperature
-20°C ~ 60°C
Storage Temperature
-30°C ~ 70°C
Humidity
5% ~ 95%, non-condensing
Physical Specifications
Dimensions
146 mm x 102 mm
Weight GW/NW
600 g / 250 g
Table 1-2: Technical Specifications
Page 9
WAFER-BT-i1
Chapter
2
2 Unpacking
Page 10
WAFER-BT-i1
2.1 Anti-static Precautions
WARNING!
Static electricity can destroy certain electronics. Make sure to follow the
ESD precautions to prevent damage to the product, and injury to the
user.
Make sure to adhere to the following guidelines:

Wear an anti-static wristband: Wearing an anti-static wristband can prevent
electrostatic discharge.

Self-grounding: Touch a grounded conductor every few minutes to discharge
any excess static buildup.

Use an anti-static pad: When configuring any circuit board, place it on an
anti-static mat.

Only handle the edges of the PCB: Don't touch the surface of the
motherboard. Hold the motherboard by the edges when handling.
2.2 Unpacking Precautions
When the WAFER-BT-i1 is unpacked, please do the following:

Follow the antistatic guidelines above.

Make sure the packing box is facing upwards when opening.

Make sure all the packing list items are present.
Page 11
WAFER-BT-i1
2.3 Packing List
NOTE:
If any of the components listed in the checklist below are missing, do not
proceed with the installation. Contact the IEI reseller or vendor the
WAFER-BT-i1 was purchased from or contact an IEI sales representative
directly by sending an email to [email protected]
The WAFER-BT-i1 is shipped with the following components:
Quantity
1
Item and Part Number
WAFER-BT-i1 single board computer with
heat sink
1
Audio cable
(P/N: 32000-072100-RS)
1
SATA with 5V output cable kit
(P/N: 32801-000201-100-RS)
1
Power cable
(P/N: 32100-087100-RS)
1
Page 12
Utility CD
Image
WAFER-BT-i1
1
One Key Recovery CD
1
Quick Installation Guide
2.4 Optional Items
The following are optional components which may be separately purchased:
Item and Part Number
Image
Dual-port USB cable without bracket
(P/N: 32000-070301-RS)
RS-422/485 cable
(P/N: 32205-003800-300-RS)
PS/2 KB/MS Y-cable without bracket
(P/N: 32006-000300-100-RS)
Page 13
WAFER-BT-i1
Chapter
3
3 Connectors
Page 14
WAFER-BT-i1
3.1 Peripheral Interface Connectors
This chapter details all the jumpers and connectors.
3.1.1 WAFER-BT-i1 Layout
The figures below show all the connectors and jumpers.
Figure 3-1: Connector and Jumper Locations (Front)
3.1.2 Peripheral Interface Connectors
The table below lists all the connectors on the board.
Connector
Type
Label
+12V DC-IN power connector
4-pin Molex
CN5
Audio connector
10-pin header
AUDIO1
Page 15
WAFER-BT-i1
Battery connector
2-pin wafer
BAT1
Buzzer connector
2-pin wafer
SP1
CPU fan connector
4-pin wafer
CPU_FAN1
System fan connector
4-pin wafer
SYS_FAN1
DDR3L SO-DIMM slot
DDR3L SO-DIMM slot
DIMM1
Digital I/O connector
10-pin header
DIO1
Display port connector
20-pin header
DP1
Front panel connector
6-pin wafer
CN4
iRIS-1010 module slot
iRIS-1010 module slot
IPMI1
Keyboard & mouse connector
6-pin wafer
KB_MS1
LVDS panel Connector
30-pin crimp
LVDS1
LCD panel backlight power connector
5-pin wafer
INV1
LAN LED connector
2-pin header
JP2, JP3
PCIe mini card slot
PCIe Mini card slot
CN1
Power button connector
2-pin wafer
PWR_BTN1
Reset button connector
2-pin wafer
RST_BTN1
RS-232 serial port connectors
10-pin header
COM2, COM3
RS-422/485 serial port connector
4-pin wafer
COM4
SATA 3Gb/s drive connectors
7-pin SATA connector
SATA1, SATA2
SATA power connectors
2-pin wafer
SATA_PWR1,
SATA_PWR2
SMBUS connector
4-pin wafer
CN2
USB 2.0 connectors
8-pin header
USB1, USB4
Table 3-1: Peripheral Interface Connectors
Page 16
WAFER-BT-i1
3.1.3 External Interface Panel Connectors
The table below lists the connectors on the external I/O panel.
Connector
Type
Label
LAN connector
RJ-45
LAN1
RS-232 serial port connector
DB-9 male
COM1
USB 2.0 connector
USB 2.0
USB2
USB 3.0 connector
USB 3.0
USB3
VGA Connector
15-pin female
VGA1
Table 3-2: Rear Panel Connectors
3.2 Internal Peripheral Connectors
The section describes all of the connectors on the WAFER-BT-i1.
3.2.1 +12V DC-IN Power Connector
CN Label:
CN5
CN Type:
4-pin Molex, p=4.2 mm
CN Location:
See Figure 3-2
CN Pinouts:
See Table 3-3
The connector supports the +12V power supply.
Page 17
WAFER-BT-i1
Figure 3-2: +12V DC-IN Power Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
GND
3
+12V
4
+12V
Table 3-3: +12V DC-IN Power Connector Pinouts
3.2.2 Audio Connector
CN Label:
AUDIO1
CN Type:
10-pin header, p=2.00 mm
CN Location:
See Figure 3-3
CN Pinouts:
See Table 3-4
The audio connector is connected to external audio devices including speakers and
microphones for the input and output of audio signals to and from the system.
Page 18
WAFER-BT-i1
Figure 3-3: Audio Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
LINE_OUTR
2
LINEIN_R
3
Analog_GND
4
Analog_GND
5
LINE_OUTL
6
LINEIN_L
7
Analog_GND
8
Analog_GND
9
LMIC1-R
10
LMIC1-L
Table 3-4: Audio Connector Pinouts
3.2.3 Battery Connector
CN Label:
BAT1
CN Type:
2-pin wafer, p=1.25 mm
CN Location:
See Figure 3-4
CN Pinouts:
See Table 3-5
The battery connector is connected to the system battery. The battery provides power to
the system clock to retain the time when power is turned off.
Page 19
WAFER-BT-i1
Figure 3-4: Battery Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
VBATT
2
GND
Table 3-5: Battery Connector Pinouts
3.2.4 Buzzer Connector
CN Label:
SP1
CN Type:
2-pin wafer, p=1.25 mm
CN Location:
See Figure 3-5
CN Pinouts:
See Table 3-6
The buzzer connector is connected to the buzzer.
Figure 3-5: Buzzer Connector Location
Page 20
WAFER-BT-i1
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
Buzzer +
2
Buzzer -
Table 3-6: Buzzer Connector Pinouts
3.2.5 CPU Fan Connector
CN Label:
CPU_FAN1
CN Type:
4-pin wafer, p=2.54 mm
CN Location:
See Figure 3-6
CN Pinouts:
See Table 3-7
The fan connector attaches to a cooling fan.
Figure 3-6: CPU Fan Connector Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
+12V
3
FANIO1
4
FANOUT1
Table 3-7: CPU Fan Connector Pinouts
3.2.6 DDR3L SO-DIMM Slot
CN Label:
DIMM1
CN Type:
DDR3L SO-DIMM slot
CN Location:
See Figure 3-7
The DDR3L SO-DIMM slot is for DDR3L SO-DIMM memory module.
Page 21
WAFER-BT-i1
Figure 3-7: DDR3L SO-DIMM Slot Location
3.2.7 Digital I/O Connector
CN Label:
DIO1
CN Type:
10-pin header, p=2.00 mm
CN Location:
See Figure 3-8
CN Pinouts:
See Table 3-8
The digital I/O connector provides programmable input and output for external devices.
The digital I/O provides 4-bit output and 4-bit input.
Figure 3-8: Digital I/O Connector Location
Page 22
WAFER-BT-i1
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
+5V
3
DGPO3
4
DGPO2
5
DGPO1
6
DGPO0
7
DGPI3
8
DGPI2
9
DGPI1
10
DGPI0
Table 3-8: Digital I/O Connector Pinouts
3.2.8 Display Port Connector
CN Label:
DP1
CN Type:
20-pin box header, p=2.00 mm
CN Location:
See Figure 3-9
CN Pinouts:
See Table 3-9
The disport port connector provides flexible display function that supports VGA, DVI,
LVDS, HDMI and DisplayPort via the disport port convert board.
Figure 3-9: Display Port Connector Location
Page 23
WAFER-BT-i1
Pin
Description
Pin
Description
1
+5V
2
DPD_OB_LANE1_N
3
DPD_OB_LANE1_P
4
GND
5
DPD_OB_LANE3_N
6
DPD_OB_LANE3_P
7
GND
8
AUX_CTRL_DET_D
9
GND
10
DDI1_HPD#
11
DPD_AUX_CTRL_P2
12
DPD_AUX_CTRL_N2
13
GND
14
DPD_OB_LANE2_P
15
DPD_OB_LANE2_N
16
GND
17
DPD_OB_LANE0_P
18
DPD_OB_LANE0_N
19
+3.3V
20
NC
Table 3-9: Display Port Connector Pinouts
3.2.9 Front Panel Connector
CN Label:
CN4
CN Type:
6-pin wafer, p=2.00 mm
CN Location:
See Figure 3-10
CN Pinouts:
See Table 3-10
The front panel connector connects to the indicator LEDs on the system front panel.
Figure 3-10: Front Panel Connector Location
Page 24
WAFER-BT-i1
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
2
GND
3
PWR_LED+
4
PWR_LED-
5
HDD_LED+
6
HDD_LED-
Table 3-10: Front Panel Connector Pinouts
3.2.10 iRIS-1010 module slot
CN Label:
IPMI1
CN Type:
IPMI 2.0 slot
CN Location:
See Figure 3-11
The iRIS-1010 module slot allows installation of the iRIS-1010 module.
Figure 3-11: iRIS-1010 Module Slot Location
WARNING:
The iRIS-1010 module slot is designed to install the IEI iRIS-1010 IPMI
2.0 module. DO NOT install other modules into the iRIS-1010 module
slot. Doing so may cause damage to the WAFER-BT-i1.
Page 25
WAFER-BT-i1
3.2.11 Keyboard and Mouse Connector
CN Label:
KB_MS1
CN Type:
6-pin wafer, p=2.00 mm
CN Location:
See Figure 3-12
CN Pinouts:
See Table 3-11
The keyboard/mouse connector connects to a PS/2 Y-cable that can be connected to a
PS/2 keyboard and mouse.
Figure 3-12: Keyboard and Mouse Location
Pin
Description
1
VCC
2
Mouse Data
3
Mouse Clock
4
Keyboard Data
5
Keyboard Clock
6
GND
Table 3-11: Keyboard and Mouse Connector Pinouts
3.2.12 LVDS Backlight Inverter Connector
CN Label:
INV1
CN Type:
5-pin wafer, p=2.00 mm
CN Location:
See Figure 3-13
Page 26
WAFER-BT-i1
CN Pinouts:
See Table 3-12
The backlight inverter connector provides power to an LCD panel.
Figure 3-13: Backlight Inverter Connector Location
Pin
Description
1
BRIGHTNESS2
2
GND
3
12V
4
GND
5
ENABKL2
Table 3-12: Backlight Inverter Connector Pinouts
3.2.13 LVDS LCD Connector
CN Label:
LVDS1
CN Type:
30-pin crimp, p=1.25 mm
CN Location:
See Figure 3-14
CN Pinouts:
See Table 3-13
The LVDS connector is for an LCD panel connected to the board.
Page 27
WAFER-BT-i1
Figure 3-14: LVDS Connector Location
Pin
Description
Pin
Description
1
GROUND
2
GROUND
3
LVDS_A_TX0-P
4
LVDS_A_TX0-N
5
LVDS_A_TX1-P
6
LVDS_A_TX1-N
7
LVDS_A_TX2-P
8
LVDS_A_TX2-N
9
LVDS_A_TXCLK-P
10
LVDS_A_TXCLK-N
11
LVDS_A_TX3-P
12
LVDS_A_TX3-N
13
GROUND
14
GROUND
15
LVDS_B_TX0-P
16
LVDS_B_TX0-N
17
LVDS_B_TX1-P
18
LVDS_B_TX1-N
19
LVDS_B_TX2-P
20
LVDS_B_TX2-N
21
LVDS_B_TXCLK-P
22
LVDS_B_TXCLK-N
23
LVDS_B_TX3-P
24
LVDS_B_TX3-N
25
GROUND
26
GROUND
27
+LCD VCC
28
+LCD VCC
29
+LCD VCC
30
+LCD VCC
Table 3-13: LVDS Connector Pinouts
Page 28
WAFER-BT-i1
3.2.14 LAN LED Connector
CN Label:
JP2, JP3
CN Type:
2-pin header, p=2.00 mm
CN Location:
See Figure 3-15
CN Pinouts:
See Table 3-14
The LAN LED connectors connect to the LAN link LEDs on the system.
Figure 3-15: LAN LED Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+3.3VLAN
2
LAN_LED_LINK#
Table 3-14: LAN LED Connector Pinouts
3.2.15 PCIe Mini Card Slot
CN Label:
CN1
CN Type:
PCIe Mini card slot
CN Location:
See Figure 3-16
5
The PCIe Mini card slot is for installing a PCIe Mini expansion card or an mSATA module.
Page 29
WAFER-BT-i1
Figure 3-16: PCIe Mini Card Slot Location
NOTE:
If an mSATA module is installed in the PCIe Mini slot (CN1), the SATA
port 2 (SATA2) will be disabled. Choose either the SATA2 connector or
the mSATA module for storage.
3.2.16 Power Button Connector
CN Label:
PWR_BTN1
CN Type:
2-pin wafer, p=2.00 mm
CN Location:
See Figure 3-17
CN Pinouts:
See Table 3-15
The power button connector is connected to a power switch on the system chassis to
enable users to turn the system on and off.
Page 30
WAFER-BT-i1
Figure 3-17: Power Button Connector Location
Pin
Description
1
PWRBTN_SW#
2
GND
Table 3-15: Power Button Connector Pinouts
3.2.17 Reset Button Connector
CN Label:
RST_BTN1
CN Type:
2-pin wafer, p=2.00 mm
CN Location:
See Figure 3-18
CN Pinouts:
See Table 3-16
The reset button connector is connected to a reset switch on the system chassis to enable
users to reboot the system when the system is turned on.
Page 31
WAFER-BT-i1
Figure 3-18: Reset Button Connector Location
Pin
Description
1
PM_SYSRST_R#
2
GND
Table 3-16: Reset Button Connector Pinouts
3.2.18 RS-232 Serial Port Connectors
CN Label:
COM2, COM3
CN Type:
10-pin header, p=2.00 mm
CN Location:
See Figure 3-19
CN Pinouts:
See Table 3-17
The serial connector provides RS-232 connection.
Figure 3-19: RS-232 Serial Port Connectors Locations
Page 32
WAFER-BT-i1
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
DCD
2
DSR
3
RXD
4
RTS
5
TXD
6
CTS
7
DTR
8
RI
9
GND
10
GND
Table 3-17: RS-232 Serial Port Connector Pinouts
3.2.19 RS-422/485 Serial Port Connector
CN Label:
COM4
CN Type:
4-pin wafer, p=2.00 mm
CN Location:
See Figure 3-20
CN Pinouts:
See Table 3-18
This connector provides RS-422 or RS-485 communications.
Figure 3-20: RS-422/485 Connector Location
Pin
Description
Pin
Description
1
RXD422-
2
RXD422+
3
TXD422+/TXD485+
4
TXD422-/TXD485-
Table 3-18: RS-422/485 Connector Pinouts
Page 33
WAFER-BT-i1
Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the DB-9
connector are listed below.
RS-422 Pinouts
RS-485 Pinouts
Table 3-19: DB-9 RS-422/485 Pinouts
3.2.20 SATA 3Gb/s Drive Connectors
CN Label:
SATA1, SATA2
CN Type:
7-pin SATA connector
CN Location:
See Figure 3-21
The SATA 3Gb/s drive connector is connected to a SATA 3Gb/s drive. The SATA 3Gb/s
drive transfers data at speeds as high as 3Gb/s.
Figure 3-21: SATA 3Gb/s Drive Connectors Locations
Page 34
WAFER-BT-i1
NOTE:
If an HDD is connected to the SATA port 2 (SATA2), an mSATA
module will not be supported by the PCIe Mini slot (CN1). Choose
either the SATA2 connector or the mSATA module for storage.
3.2.21 SATA Power Connectors
CN Label:
SATA_PWR1, SATA_PWR2
CN Type:
2-pin wafer, p=2.00 mm
CN Location:
See Figure 3-22
CN Pinouts:
See Table 3-20
The SATA power connector provides +5V power output to the SATA connector.
Figure 3-22: SATA Power Connector Locations
PIN NO.
DESCRIPTION
1
+5V
2
GND
Table 3-20: SATA Power Connector Pinouts
Page 35
WAFER-BT-i1
3.2.22 SMBUS Connector
CN Label:
CN2
CN Type:
4-pin wafer, p=1.25 mm
CN Location:
See Figure 3-23
CN Pinouts:
See Table 3-21
The SMBUS (System Management Bus) connector provides low-speed system
management communications.
Figure 3-23: SMBUS Connectors Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
SMBDATA
3
SMBCLK
4
+5V
Table 3-21: SMBUS Connectors Pinouts
3.2.23 USB Connectors
CN Label:
USB1, USB4
CN Type:
8-pin header, p=2.00 mm
CN Location:
See Figure 3-24
CN Pinouts:
See Table 3-22
Page 36
WAFER-BT-i1
The USB connectors provide four USB 2.0 ports by dual-port USB cable.
Figure 3-24: USB Connectors Locations
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
2
GND
3
-DATA_USB1/3
4
+DATA_USB2/4
5
+DATA_USB1/3
6
-DATA_USB2/4
7
GND
8
+5V
Table 3-22: USB Connectors Pinouts
3.3 External Peripheral Interface Connector Panel
Figure 3-25 shows the WAFER-BT-i1 external peripheral interface connector (EPIC)
panel. The EPIC panel consists of the following:

2 x LAN connectors

1 x USB 3.0 connector

1 x USB 2.0 connector

1 x RS-232 serial port connector

1 x VGA connector
Page 37
WAFER-BT-i1
Figure 3-25: External Peripheral Interface Connector
3.3.1 LAN Connector
CN Label:
LAN1, LAN2
CN Type:
RJ-45
CN Location:
See Figure 3-25
CN Pinouts:
See Figure 3-26 and Table 3-23
5
5
The LAN connector connects to a local network.
Figure 3-26: LAN Connector
Pin
Description
Pin
Description
1
MDIA3-
5
MDIA2+
2
MDIA3+
6
MDIA1+
3
MDIA1-
7
MDIA0-
4
MDIA2-
8
MDIA0+
Table 3-23: LAN Pinouts
Page 38
WAFER-BT-i1
LED
Description
LED
Description
A
on: linked
B
off: 10 Mb/s
blinking: data is being sent/received
green: 100 Mb/s
orange: 1000 Mb/s
Table 3-24: Connector LEDs
3.3.2 USB Connectors
CN Label:
USB2, USB3
CN Type:
USB 2.0 & USB 3.0 ports
CN Location:
See Figure 3-25
CN Pinouts:
See Table 3-26
5
5
The WAFER-BT-i1 has one external USB 2.0 port and one external USB 3.0 port. The
USB connector can be connected to a USB device. The pinouts of USB 2.0 port & USB
3.0 connectors are shown below.
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
2
-DATA_USB3
3
-DATA_USB4
4
GND
Table 3-25: USB 2.0 Port Pinouts
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
+5V
2
USB2P0-
3
USB2P0+
4
GND
5
USB3P0_RXDN1
6
USB3P0_RXDP1
7
GND
8
USB3P0_TXDN1
9
USB3P0_TXDP1
Table 3-26: USB 3.0 Port Pinouts
3.3.3 RS-232 Serial Port Connector
CN Label:
COM1
CN Type:
DB-9 Male
Page 39
WAFER-BT-i1
CN Location:
See Figure 3-25
CN Pinouts:
See Figure 3-27 and Table 3-27
The serial port connects to a RS-232 serial communications device.
Figure 3-27: RS-232 Serial Port Connector
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
DCD1
6
DSR1
2
RX1
7
RTS1
3
TX1
8
CTS1
4
DTR1
9
RI1
5
GND
Table 3-27: RS-232 Serial Port Connector Pinouts
3.3.4 VGA Connector
CN Label:
VGA1
CN Type:
15-pin female (VGA)
CN Location:
See Figure 3-25
CN Pinouts:
See Figure 3-28 and Table 3-28
The VGA port connects to a monitor that accepts a standard VGA input.
Figure 3-28: VGA Connector
Page 40
WAFER-BT-i1
PIN
DESCRIPTION
PIN
DESCRIPTION
1
Red
2
Green
3
Blue
4
NC
5
GND
6
GND
7
GND
8
GND
9
VGAVCC
10
HOTPLUG
11
NC
12
DDCDAT
13
HSYNC
14
VSYNC
15
DDCCLK
Table 3-28: VGA Connector Pinouts
Page 41
WAFER-BT-i1
Chapter
4
4 Installation
Page 42
WAFER-BT-i1
4.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
WAFER-BT-i1 may result in permanent damage to the WAFER-BT-i1
and severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the WAFER-BT-i1. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the WAFER-BT-i1 or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.

Wear an anti-static wristband: Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.

Self-grounding: Before handling the board, touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.

Use an anti-static pad: When configuring the WAFER-BT-i1, place it on an
anti-static pad. This reduces the possibility of ESD damaging the
WAFER-BT-i1.

Only handle the edges of the PCB: When handling the PCB, hold the PCB
by the edges.
4.2 Installation Considerations
NOTE:
The following installation notices and installation considerations should
be read and understood before installation. All installation notices must
be strictly adhered to. Failing to adhere to these precautions may lead
to severe damage and injury to the person performing the installation.
Page 43
WAFER-BT-i1
WARNING:
The installation instructions described in this manual should be carefully
followed in order to prevent damage to the WAFER-BT-i1, WAFER-BT-i1
components and injury to the user.
Before and during the installation please DO the following:

Read the user manual:
o
The user manual provides a complete description of the WAFER-BT-i1
installation instructions and configuration options.

Wear an electrostatic discharge cuff (ESD):
o
Electronic components are easily damaged by ESD. Wearing an ESD cuff
removes ESD from the body and helps prevent ESD damage.

Place the WAFER-BT-i1 on an antistatic pad:
o
When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.

Turn all power to the WAFER-BT-i1 off:
o
When working with the WAFER-BT-i1, make sure that it is disconnected
from all power supplies and that no electricity is being fed into the system.
Before and during the installation of the WAFER-BT-i1 DO NOT:

Remove any of the stickers on the PCB board. These stickers are required for
warranty validation.

Use the product before verifying all the cables and power connectors are
properly connected.

Allow screws to come in contact with the PCB circuit, connector pins, or its
components.
Page 44
WAFER-BT-i1
4.3 SO-DIMM Installation
WARNING:
Using incorrectly specified SO-DIMM may cause permanently damage
the WAFER-BT-i1. Please make sure the purchased SO-DIMM
complies with the memory specifications of the WAFER-BT-i1.
SO-DIMM specifications compliant with the WAFER-BT-i1 are listed in
the specification table of Chapter 1.
To install an SO-DIMM, please follow the steps below and refer to Figure 4-1.
Figure 4-1: SO-DIMM Installation
Step 1: Locate the SO-DIMM socket. Place the board on an anti-static mat.
Step 2: Align the SO-DIMM with the socket. Align the notch on the memory with the
notch on the memory socket.
Step 3: Insert the SO-DIMM. Push the memory in at a 20º angle. (See Figure 4-1)
Step 4: Seat the SO-DIMM. Gently push downwards and the arms clip into place. (See
Figure 4-1)
Page 45
WAFER-BT-i1
4.4 Full-size PCIe Mini Card Installation
The PCIe Mini card slot allows installation of either a full-size or half-size PCIe Mini card.
To install a full-size PCIe Mini card, please follow the steps below.
Step 1: Locate the PCIe Mini card slot. See Figure 3-16.
Step 2: Remove the retention screw. Remove the retention screw as shown in
Figure 4-2.
Figure 4-2: Removing the Retention Screw
Step 3: Remove the retention screw and standoff. Unscrew and remove the retention
screw and standoff for half-size PCIe Mini card secured on the motherboard as
shown in Figure 4-3.
Page 46
WAFER-BT-i1
Figure 4-3: Removing the Retention Screw and Standoff
Step 4: Insert into the socket at an angle. Line up the notch on the card with the notch
on the slot. Slide the PCIe Mini card into the socket at an angle of about 20º
(Figure 4-4).
Figure 4-4: Inserting the Full-size PCIe Mini Card into the Slot at an Angle
Page 47
WAFER-BT-i1
Step 5: Secure the full-size PCIe Mini card. Secure the full-size PCIe Mini card with
the retention screw previously removed (Figure 4-5).
Figure 4-5: Securing the Full-size PCIe Mini Card
NOTE:
If an mSATA module is installed in the PCIe Mini slot (CN1), the SATA
port 2 (SATA2) will be disabled. Choose either the SATA2 connector or
the mSATA module for storage.
Page 48
WAFER-BT-i1
4.5 Half-size PCIe Mini Card Installation
The PCIe Mini card slot allows installation of either a full-size or half-size PCIe Mini card.
To install a half-size PCIe Mini card, please follow the steps below.
Step 1: Locate the PCIe Mini card slot. See Figure 3-16.
Step 2: Remove the retention screw. Remove the retention screw as shown in
Figure 4-6.
Figure 4-6: Removing the Retention Screw
Step 3: Insert into the socket at an angle. Line up the notch on the card with the notch
on the slot. Slide the PCIe Mini card into the socket at an angle of about 20º
(Figure 4-7).
Page 49
WAFER-BT-i1
Figure 4-7: Inserting the Half-size PCIe Mini Card into the Slot at an Angle
Step 4: Secure the half-size PCIe Mini card. Secure the full-size PCIe Mini card with
the retention screw previously removed (Figure 4-5).
Figure 4-8: Securing the Half-size PCIe Mini Card
Page 50
WAFER-BT-i1
4.6 System Configuration
The system configuration is controlled by buttons, jumpers and switches. The system
configuration should be performed before installation.
4.6.1 AT/ATX Mode Select Switch
CN Label:
J_ATX_AT1
CN Type:
switch
CN Location:
See Figure 4-9
CN Settings:
See Table 4-1
The AT/ATX mode select switch specifies the systems power mode as AT or ATX.
AT/ATX mode select switch settings are shown in Table 4-1.
Setting
Description
Short A-B
ATX Mode (Default)
Short B-C
AT Mode
Table 4-1: AT/ATX Mode Select Switch Settings
The location of the AT/ATX mode select switch is shown in Figure 4-9 below.
Figure 4-9: AT/ATX Mode Select Switch Location
Page 51
WAFER-BT-i1
4.6.2 Clear CMOS Button
CN Label:
J_CMOS1
CN Type:
button
CN Location:
See Figure 4-3
CN Settings:
See Table 4-2
If the WAFER-BT-i1 fails to boot due to improper BIOS settings, use the button to clear the
CMOS data and reset the system BIOS information.
The clear CMOS button settings are shown in Table 4-2.
Setting
Description
Open
Normal Operation
Push
Clear CMOS Setup
Default
Table 4-2: Clear CMOS Button Settings
The location of the clear CMOS button is shown in Figure 4-3
Figure 4-10: Clear CMOS Button Location
4.6.3 LVDS Panel Resolution Selection
Jumper Label:
SW1
Jumper Type:
DIP switch
Jumper Settings:
See Table 4-3
Jumper Location:
See Figure 4-11
Page 52
WAFER-BT-i1
Selects the resolution of the LCD panel connected to the LVDS connector.
* ON=0, OFF=1; Single=S, Dual=D
SW1 (4-3-2-1)
Description
0000
800x600 18-bit S
0001
1024x768 18-bit S
0010
1024x768 24-bit S
0011
1280x768 18-bit S
0100
1280x800 18-bit S
0101
1280x960 18-bit S
0110
1280x1024 24-bit D
0111
1366x768 18-bit S
1000
1366x768 24-bit S
1001
1440x960 24-bit D
1010
1400x1050 24-bit D
1011
1600x900 24-bit D
1100
1680x1050 24-bit D
1101
1600x1200 24-bit D
1110
1920x1080 24-bit D
1111
1920x1200 24-bit D
(default)
Table 4-3: LVDS Panel Resolution Selection
Page 53
WAFER-BT-i1
Figure 4-11: LVDS Panel Resolution Selection Switch Location
4.6.4 LVDS Voltage Selection
WARNING:
Permanent damage to the screen and WAFER-BT-i1 may occur if the
wrong voltage is selected with this jumper. Please refer to the user
guide that came with the monitor to select the correct voltage.
Jumper Label:
J_LCD_PWR1
Jumper Type:
switch
Jumper Settings:
See Table 4-4
Jumper Location:
See Figure 4-12
The LVDS voltage selection jumper allows setting the voltage provided to the monitor
connected to the LVDS connector.
Setting
Description
Short A-B
+3.3V (Default)
Short B-C
+5V
Table 4-4: LVDS Voltage Selection Jumper Settings
Page 54
WAFER-BT-i1
Figure 4-12: LVDS Voltage Selection Jumper Location
4.6.5 Flash Descriptor Security Override Jumper
Jumper Label:
J_FLASH1
Jumper Type:
3-pin header
Jumper Settings:
See Table 4-5
Jumper Location:
See Figure 4-13
The Flash Descriptor Security Override jumper specifies whether to override the flash
descriptor.
Setting
Description
Short 1-2
No override (Default)
Short 2-3
Override
Table 4-5: Flash Descriptor Security Override Jumper Settings
Page 55
WAFER-BT-i1
Figure 4-13: Flash Descriptor Security Override Jumper Location
4.7 Chassis Installation
4.7.1 Heat Sink Enclosure
WARNING:
Never run the WAFER-BT-i1 without the heat sink secured to the
board. The heat sink ensures the system remains cool and does not
need addition heat sinks to cool the system.
WARNING:
When running the WAFER-BT-i1, do not put the WAFER-BT-i1 directly
on a surface that can not dissipate system heat, especially the wooden
or plastic surface. It is highly recommended to run the WAFER-BT-i1
 on a heat dissipation surface or
 using copper pillars to hold the board up from the chassis
When the WAFER-BT-i1 is shipped, it is secured to a heat sink with four retention screws.
If the WAFER-BT-i1 must be removed from the heat sink, the four retention screws must
be removed.
Page 56
WAFER-BT-i1
4.7.2 Motherboard Installation
Each side of the heat sink enclosure has several screw holes allowing the WAFER-BT-i1
to be mounted into a chassis (please refer to Figure 1-3 for the detailed dimensions). The
user can design or select a chassis that has screw holes matching up with the holes on
the heat sink enclosure for installing the WAFER-BT-i1. The following diagram shows an
example of motherboard installation.
Figure 4-14: Motherboard Installation Example
Page 57
WAFER-BT-i1
4.8 Internal Peripheral Device Connections
This section outlines the installation of peripheral devices to the on-board connectors
4.8.1 Audio Kit Installation
The Audio Kit that came with the WAFER-BT-i1 connects to the audio connector on the
WAFER-BT-i1. The audio kit consists of three audio jacks. Mic-in connects to a
microphone. Line-in provides a stereo line-level input to connect to the output of an audio
device. Line-out, a stereo line-level output, connects to two amplified speakers. To install
the audio kit, please refer to the steps below:
Step 1: Locate the audio connector. The location of the 10-pin audio connector is
shown in Chapter 3.
Step 2: Align pin 1. Align pin 1 on the on-board connector with pin 1 on the audio kit
connector. Pin 1 on the audio kit connector is indicated with a white dot. See
Figure 4-15.
Figure 4-15: Audio Kit Cable Connection
Page 58
WAFER-BT-i1
Step 3: Connect the audio devices. Connect speakers to the line-out audio jack.
Connect the output of an audio device to the line-in audio jack. Connect a
microphone to the mic-in audio jack.Step 0:
4.8.2 SATA Drive Connection
The WAFER-BT-i1 is shipped with a SATA drive cable. To connect the SATA drive to the
connector, please follow the steps below.
Step 1: Locate the SATA connector and the SATA power connector. The locations of
the connectors are shown in Chapter 3.
Step 2: Insert the cable connector. Insert the cable connector into the on-board SATA
drive connector and the SATA power connector. See Figure 4-16.
Figure 4-16: SATA Drive Cable Connection
Step 3: Connect the cable to the SATA disk. Connect the connector on the other end
of the cable to the connector at the back of the SATA drive. See Figure 4-16.
Page 59
WAFER-BT-i1
Step 4: To remove the SATA cable from the SATA connector, press the clip on the
connector at the end of the cable. Step 0:
4.8.3 Single RS-232 Cable
The single RS-232 cable consists of one serial port connector attached to a serial
communications cable that is then attached to a D-sub 9 male connector. To install the
single RS-232 cable, please follow the steps below.
Step 1: Locate the connector. The location of the RS-232 connector is shown in
Chapter 3.
Step 2: Insert the cable connector. Insert the connector into the serial port box header.
See Figure 4-17. A key on the front of the cable connectors ensures the
connector can only be installed in one direction.
Figure 4-17: Single RS-232 Cable Installation
Step 3: Secure the bracket. The single RS-232 connector has two retention screws
that must be secured to a chassis or bracket.
Step 4: Connect the serial device. Once the single RS-232 connector is connected to
a chassis or bracket, a serial communications device can be connected to the
system.
Page 60
WAFER-BT-i1
Chapter
5
5 BIOS
Page 61
WAFER-BT-i1
5.1 Introduction
The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to
certain system settings. This chapter outlines the options that can be changed.
NOTE:
Some of the BIOS options may vary throughout the life cycle of the
product and are subject to change without prior notice.
5.1.1 Starting Setup
The UEFI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DELETE or F2 key as soon as the system is turned on or
2. Press the DELETE or F2 key when the “Press Del to enter SETUP” message
appears on the screen. 0.
If the message disappears before the DELETE or F2 key is pressed, restart the computer
and try again.
5.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press ESC to quit. Navigation
keys are shown in.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
+
Increase the numeric value or make changes
Page 62
WAFER-BT-i1
Key
Function
-
Decrease the numeric value or make changes
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
F2 key
Load previous values.
F3 key
Load optimized defaults
F4 key
Save changes and Exit BIOS
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
Table 5-1: BIOS Navigation Keys
5.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC or
the F1 key again.
5.1.4 Unable to Reboot after Configuration Changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter 3.
5.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:

Main – Changes the basic system configuration.

Advanced – Changes the advanced system settings.

Chipset – Changes the chipset settings.

Boot – Changes the system boot configuration.

Security – Sets User and Supervisor Passwords.

Save & Exit – Selects exit options and loads default settings
Page 63
WAFER-BT-i1
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
5.2 Main
The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
BIOS Information
BIOS Vendor
Core Version
Compliency
Project Version
Build Date and Time
American Megatrends
5.009
UEFI 2.3; PI 1.2
SAA8AR10.rom
06/20/2014 16:50:03
iWDD Vendor
iWDD Version
iEi
SAA8ER10.bin
IPMI Module
N/A
Memory Information
Total Memory
4096 MB(LPDDR3)
Set the Date. Use Tab to
switch between Data
elements.
---------------------
: Select Screen
 : Select Item
Enter Select
+/-: Change Opt.
System Date
[Fri 06/20/2014]
F1: General Help
System Time
[19:43:27]
F2: Previous Values
F3: Optimized Defaults
Access Level
Administrator
F4: Save & Exit
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
TXE Information
Sec RC Version
TXE FW Version
00.05.00.00
01.00.02.1060
BIOS Menu 1: Main
The Main menu lists the following system details:

BIOS Information

iWDD Information

Memory Information

TXE Information
The System Overview field also has two user configurable fields:
Page 64
WAFER-BT-i1

System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.

System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
5.3 Advanced
Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
WARNING!
Setting the wrong values in the sections below may cause the system
to malfunction. Make sure that the settings made are compatible with
the hardware.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
>
>
>
>
>
>
>
>
ACPI Settings
Super IO Configuration
Hardware Monitor
RTC Wake Settings
Serial Port Console Redirection
CPU Configuration
IDE Configuration
USB Configuration
System ACPI Parameters.
---------------------: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 2: Advanced
Page 65
WAFER-BT-i1
5.3.1 ACPI Settings
The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and
5
Power Interface (ACPI) options.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
ACPI Settings
ACPI Sleep State
[S3 (Suspend to RAM]
---------------------: Select Screen
 : Select Item
Enter Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 3: ACPI Configuration

ACPI Sleep State [S3 only (Suspend to RAM)]
The fields in ACPI Sleep State option cannot be changed.

Suspend Disabled

S3
(Suspend
RAM)
to
Disable the suspend function.
DEFAULT
The caches are flushed and the CPU is powered
off. Power to the RAM is maintained. The
computer returns slower to a working state, but
more power is saved.
Page 66
WAFER-BT-i1
5.3.2 Super IO Configuration
Use the Super IO Configuration menu (BIOS Menu 4) to set or change the
configurations for the serial ports.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Super IO Configuration
Super IO
> Serial
> Serial
> Serial
> Serial
Chip
Port
Port
Port
Port
Set Parameters of Serial
Port 1 (COMA)
F81866
1
2
3
4
Configuration
Configuration
Configuration
Configuration
--------------------: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 4: Super IO Configuration
5.3.2.1 Serial Port n Configuration
Use the Serial Port n Configuration menu (BIOS Menu 5) to configure the serial port n.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
F81216 Serial Port 1 Configuration
Serial Port
Device Settings
Enable or Disable Serial
Port (COM)
[Enabled]
IO=3F8h; IRQ=4
--------------------: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
Change Settings
[Auto]
BIOS Menu 5: Serial Port n Configuration Menu
Page 67
WAFER-BT-i1
5.3.2.1.1 Serial Port 1 Configuration

Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt
address are automatically detected.

IO=3F8h; IRQ=4
Serial Port I/O port address is 3F8h and the
interrupt address is IRQ4




IO=3F8h; IRQ=3,
Serial Port I/O port address is 3F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F8h; IRQ=3,
Serial Port I/O port address is 2F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=3E8h; IRQ=3,
Serial Port I/O port address is 3E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E8h; IRQ=3,
Serial Port I/O port address is 2E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
5.3.2.1.2 Serial Port 2 Configuration

Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.

Page 68
Disabled
Disable the serial port
WAFER-BT-i1


Enabled
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt
address are automatically detected.

IO=2F8h; IRQ=3
Serial Port I/O port address is 2F8h and the
interrupt address is IRQ3




IO=3F8h; IRQ=3,
Serial Port I/O port address is 3F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F8h; IRQ=3,
Serial Port I/O port address is 2F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=3E8h; IRQ=3,
Serial Port I/O port address is 3E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E8h; IRQ=3,
Serial Port I/O port address is 2E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
5.3.2.1.3 Serial Port 3 Configuration

Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.
Page 69
WAFER-BT-i1

Auto
DEFAULT
The serial port IO port address and interrupt
address are automatically detected.

Serial Port I/O port address is 3E8h and the
IO=3E8h; IRQ=7
interrupt address is IRQ7






IO=3F8h; IRQ=3,
Serial Port I/O port address is 3F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F8h; IRQ=3,
Serial Port I/O port address is 2F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=3E8h; IRQ=3,
Serial Port I/O port address is 3E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E8h; IRQ=3,
Serial Port I/O port address is 2E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F0h; IRQ=3,
Serial Port I/O port address is 2F0h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E0h; IRQ=3,
Serial Port I/O port address is 2E0h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
5.3.2.1.4 Serial Port 4 Configuration

Serial Port [Enabled]
Use the Serial Port option to enable or disable the serial port.


Disabled

Enabled
Disable the serial port
DEFAULT
Enable the serial port
Change Settings [Auto]
Use the Change Settings option to change the serial port IO port address and interrupt
address.

Auto
DEFAULT
The serial port IO port address and interrupt
address are automatically detected.
Page 70
WAFER-BT-i1

IO=2E8h; IRQ=7
Serial Port I/O port address is 2E8h and the
interrupt address is IRQ7






IO=3F8h; IRQ=3,
Serial Port I/O port address is 3F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F8h; IRQ=3,
Serial Port I/O port address is 2F8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=3E8h; IRQ=3,
Serial Port I/O port address is 3E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E8h; IRQ=3,
Serial Port I/O port address is 2E8h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2F0h; IRQ=3,
Serial Port I/O port address is 2F0h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
IO=2E0h; IRQ=3,
Serial Port I/O port address is 2E0h and the
4,5,6,7,9,10,11,12
interrupt address is IRQ3,4,5,6,7,9,10,11,12
5.3.3 Hardware Monitor
The Hardware Monitor menu (BIOS Menu 6) contains the fan configuration submenus
and displays operating temperature, fan speeds and system voltages.
Page 71
WAFER-BT-i1
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
PC Health Status
Enable or Disable Smart
Fan
> Smart Fan Function
CPU temperature
System temperature
CPU Fan Speed
SYS Fan Speed
:+57 C
:+42 C
:N/A
:N/A
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 6: Hardware Monitor

PC Health Status
The following system parameters and values are shown. The system parameters that are
monitored are:

System Temperatures:
o
o

CPU Temperature
System temperature
Fan Speed:
o
o
CPU Fan Speed
SYS Fan Speed
5.3.3.1 Smart Fan Mode Configuration
Use the Smart Fan Mode Configuration submenu (BIOS Menu 7) to configure fan
temperature and speed settings.
Page 72
WAFER-BT-i1
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Smart Fan Mode Configuration
CPU Smart Fan control
Temperature of Off
Temperature of Start
Start PWM
Slope(Duty Cycle)
CPU Smart Fan control
settings.
[Auto PWM Mode]
75
80
30
[4]
--------------------: Select Screen
 : Select Item
Enter Select
+ - Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 7: Smart Fan Mode Configuration

CPU Smart Fan control [Auto PWM Mode]
Use the CPU Smart Fan control BIOS option to configure the CPU Smart Fan.

Full Mode
Fan is on all the time

Manual PWM Mode
The fan spins at the speed set in the manual
PWM setting

Auto PWM Mode
DEFAULT
The fan adjusts its speed using these
settings:
Temperature of Off
Temperature of Start
Start PWM
Slope (Duty Cycle)

Temperature of Off [75]
WARNING:
Setting this value too high may cause the fan to speed up only when
Page 73
WAFER-BT-i1
the CPU is at a very high temperature and therefore cause the system
to be damaged.
The Temperature of Off option can only be set if the CPU Smart Fan control option is
set to Auto Mode. If the CPU temperature is lower than Temperature of Off, the fan
speed change to be lowest. To set a value, select the Temperature of Off option and
enter a decimal number between 0 and 127. The temperature range is specified below.


Minimum Value: 0°C

Maximum Value: 127°C
Temperature of Start [80
WARNING:
Setting this value too high may cause the fan to rotate at full speed only
when the CPU is at a very high temperature and therefore cause the
system to be damaged.
The Temperature of Start option can only be set if the CPU Smart Fan control option is
set to Auto Mode. If the CPU temperature is between Temperature of Off and
Temperature of Start, the fan speed change to be Start PWM. To set a value, select the
Temperature of Start option and enter a decimal number between 0 and 127. The
temperature range is specified below.


Minimum Value: 0°C

Maximum Value: 127°C
Start PWM [30]
The Start PWM option can only be set if the CPU Smart Fan control option is set to Auto
Mode. Use the Start PWM option to set the PWM start value. To set a value, select the
Start PWM option and enter a decimal number between 0 and 100. The temperature
range is specified below.
Page 74
WAFER-BT-i1


Minimum Value: 0

Maximum Value: 100
Slope (Duty Cycle) [4]
The Slope (Duty Cycle) option can only be set if the CPU Smart Fan control option is
set to Auto Mode. Use the Slope (Duty Cycle) option to select the linear rate at which the
PWM mode increases with respect to an increase in temperature. A list of available
options is shown below:

0

1

2

4

8

16
5.3.4 RTC Wake Settings
The RTC Wake Settings menu (BIOS Menu 8) configures RTC wake event.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
Wake system with Fixed Time
[Disabled]
Enable or disable System
wake on alarm event. When
enabled, System will
wake on the
date::hr::min::sec
specified
----------------------
: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 8: RTC Wake Settings
Page 75
WAFER-BT-i1

Wake system with Fixed Time [Disabled]
Use the Wake system with Fixed Time option to enable or disable the system wake on
alarm event.

Disabled
DEFAULT
The real time clock (RTC) cannot generate a wake
event

Enabled
If selected, the Wake up every day option appears
allowing you to enable to disable the system to wake
every day at the specified time. Besides, the
following options appear with values that can be
selected:
Wake up date
Wake up hour
Wake up minute
Wake up second
After setting the alarm, the computer turns itself on
from a suspend state when the alarm goes off.
5.3.5 Serial Port Console Redirection
The Serial Port Console Redirection menu (BIOS Menu 9) allows the console
redirection options to be configured. Console redirection allows users to maintain a
system remotely by re-directing keyboard input and text output through the serial port.
Page 76
WAFER-BT-i1
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
COM1
Console Redirection
> Console Redirection Settings
[Disabled]
COM2
Console Redirection
> Console Redirection Settings
[Disabled]
COM3
Console Redirection
> Console Redirection Settings
[Disabled]
COM4
Console Redirection
> Console Redirection Settings
[Disabled]
IPMI COM (Disabled)
Console Redirection
Console Redirection
Enable or Disable
--------------------: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Port Is Disabled
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 9: Serial Port Console Redirection

Console Redirection [Disabled]
Use Console Redirection option to enable or disable the console redirection function.

Disabled

Enabled
DEFAULT
Disabled the console redirection function
Enabled the console redirection function
5.3.5.1 Console Redirection Settings
The Console Redirection Settings menu (BIOS Menu 10) allows the console redirection
5
options to be configured. The option is active when Console Redirection option is enabled.
Page 77
WAFER-BT-i1
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
COM1
Console Redirection Settings
Terminal Type
Bits per second
Data Bits
Parity
Stop Bits
[ANSI]
[115200]
[8]
[None]
[1]
Emulation: ANSI:
Extended ASCII char set.
VT100: ASCII char set.
VT100+: Extends VT100 to
support color, function
keys, etc. VT-UTF8: Uses
UTF8 encoding to map
Unicode chars onto 1 or
more bytes.
--------------------: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 10: Console Redirection Settings

Terminal Type [ANSI]
Use the Terminal Type option to specify the remote terminal type.


VT100
The target terminal type is VT100

VT100+
The target terminal type is VT100+

VT-UTF8
The target terminal type is VT-UTF8

ANSI
DEFAULT
The target terminal type is ANSI
Bits per second [115200]
Use the Bits per second option to specify the serial port transmission speed. The speed
must match the other side. Long or noisy lines may require lower speeds.

9600
Sets the serial port transmission speed at 9600.

19200
Sets the serial port transmission speed at 19200.
Page 78
WAFER-BT-i1


38400
Sets the serial port transmission speed at 38400.

57600
Sets the serial port transmission speed at 57600.

115200
DEFAULT
Sets the serial port transmission speed at 115200.
Data Bits [8]
Use the Data Bits option to specify the number of data bits.


7

8
Sets the data bits at 7.
DEFAULT
Sets the data bits at 8.
Parity [None]
Use the Parity option to specify the parity bit that can be sent with the data bits for
detecting the transmission errors.

None

Even
DEFAULT
No parity bit is sent with the data bits.
The parity bit is 0 if the number of ones in the data
bits is even.

The parity bit is 0 if the number of ones in the data
Odd
bits is odd.

The parity bit is always 1. This option does not
Mark
provide error detection.

The parity bit is always 0. This option does not
Space
provide error detection.

Stop Bits [1]
Use the Stop Bits option to specify the number of stop bits used to indicate the end of a
serial data packet. Communication with slow devices may require more than 1 stop bit.

1

2
DEFAULT
Sets the number of stop bits at 1.
Sets the number of stop bits at 2.
Page 79
WAFER-BT-i1
5.3.6 CPU Configuration
Use the CPU Configuration menu (BIOS Menu 5) to view detailed CPU specifications
and configure the CPU.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
CPU Configuration
Intel(R) Celeron(R) CPU J1900 @ 1.99GHz
CPU Signature
30678
Microcode Patch
809
Max CPU Speed
1990 MHz
Min CPU Speed
1334 MHz
Processor Cores
4
Intel HT Technology
Not Supported
Intel VT-x Technology
Supported
L1 Data Cache
L1 Code Cache
L2 Cache
L3 Cache
CPU Speed
64-bit
24 KB x 2
32 KB x 2
1024 KB x 1
Not Present
2001 MHz
Supported
When enabled, a VMM can
utilize the additional
hardware capabilities
provided by Vanderpool
Technology.
----------------------
: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
Intel Virtualization Technology [Enabled]
F3
Optimized
EIST
[Enabled]
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 11: CPU Configuration

Intel® Virtualization Technology [Disabled]
Use the Intel® Virtualization Technology option to enable or disable virtualization on the
system. When combined with third party software, Intel Virtualization technology allows
several OSs to run on the same system at the same time.


Disabled

Enabled
DEFAULT
Disables Intel Virtualization Technology.
Enables Intel Virtualization Technology.
EIST [Enabled]
Use the EIST option to enable or disable the Intel Speed Step Technology.
Page 80
WAFER-BT-i1

Disabled

Enabled
Disables the Intel Speed Step Technology.
DEFAULT
Enables the Intel Speed Step Technology.
5.3.7 IDE Configuration
Use the IDE Configuration menu (BIOS Menu 12) to change and/or set the configuration
of the SATA devices installed in the system.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
IDE Configuration
Select IDE/AHCI
SATA Mode
[AHCI Mode]
Serial-ATA Port 1
SATA Port 1 HotPlug
[Enabled]
[Disabled]
Serial-ATA Port 0
SATA Port 0 HotPlug
[Enabled]
[Disabled]
---------------------
SATA Port1
Not Present
SATA Port0
Not Present
: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 12: IDE Configuration

SATA Mode [ACHI Mode]
Use the SATA Mode option to configure SATA devices as normal IDE devices.


IDE Mode

ACHI Mode
Configures SATA devices as normal IDE device.
DEFAULT
Configures SATA devices as AHCI device.
Serial-ATA Port 1/0 [Enabled]
Use the Serial-ATA Port 1/0 option to enable or disable the SATA device.

Disabled

Enabled
Disables the SATA device.
DEFAULT
Enables the SATA device.
Page 81
WAFER-BT-i1

SATA Port 1/0 HotPlug [Disabled]
Use the Serial-ATA Port 1/0 HotPlug option to enable or disable the SATA device hot
plug.

Disabled

Enabled
Disables the SATA device hot plug.
DEFAULT
Enables the SATA device hot plug
5.3.8 USB Configuration
Use the USB Configuration menu (BIOS Menu 13) to read USB configuration
information and configure the USB settings.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
USB Configuration
USB Devices:
1 Keyboard
Legacy USB Support
[Enabled]
Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
--------------------: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 13: USB Configuration

USB Devices
The USB Devices Enabled field lists the USB devices that are enabled on the system
Page 82
WAFER-BT-i1

Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
keyboard can control the system even when there is no USB driver loaded onto the
system.

Enabled

Disabled
Legacy USB support disabled

Auto
Legacy USB support disabled if no USB devices are
DEFAULT
Legacy USB support enabled
connected
5.4 Chipset
Use the Chipset menu (BIOS Menu 14) to access the Northbridge and Southbridge
configuration menus
WARNING!
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
Page 83
WAFER-BT-i1
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset
Security
Boot
Save & Exit
> North Bridge
> South Bridge
North Bridge Parameters
--------------------: Select Screen
 : Select Item
Enter Select
+/-: Change Opt.
F1
General Help
F2
Previous Values
F3
Optimized Defaults
F4
Save & Exit
ESC Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 14: Chipset
5.4.1 North Bridge Configuration
Use the North Bridge Configuration menu (BIOS Menu 15) to configure the Intel IGD
settings.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
> Intel IGD Configuration
Memory Information
Total Memory
Memory Slot0
Configure Intel IGD
Settings.
4096 MB(LPDDR3)
4096 MB(LPDDR3)
--------------------: Select Screen
 : Select Item
Enter Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 15: Northbridge Chipset Configuration
Page 84
WAFER-BT-i1

Memory Information
The Memory Information lists a brief summary of the on-board memory. The fields in
Memory Information cannot be changed.
5.4.1.1 Intel IGD Configuration
Use the Intel IGD Configuration menu (BIOS Menu 16) to configure the video device
connected to the system.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
DVMT Pre-Allocated
DVMT Total Gfx Mem
[256M]
[MAX]
Primary IGFX Boot Display
[VBIOS Default]
Select DVMT 5.0
Pre-Allocated (Fixed)
Graphics Memory size
used by the Internal
Graphics Device.
--------------------: Select Screen
 : Select Item
Enter Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 16: Integrated Graphics

DVMT Pre-Allocated [256MB]
Use the DVMT Pre-Allocated option to set the amount of system memory allocated to the
integrated graphics processor when the system boots. The system memory allocated can
then only be used as graphics memory, and is no longer available to applications or the
operating system. Configuration options are listed below:

64M

128M

256M

512M
Default
Page 85
WAFER-BT-i1

DVMT Total Gfx Mem [MAX]
Use the DVMT Total Gfx Mem option to select DVMT5.0 total graphic memory size used
by the internal graphic device. The following options are available:


128M

256M

MAX
Default
Primary IGFX Boot Display [VBIOS Default]
Use the Primary IGFX Boot Display option to select the display device used by the
system when it boots. For dual display support, select “VBIOS Deafult.” Configuration
options are listed below.

VBIOS Default DEFAULT

CRT

LVDS

DP Port
5.4.2 Southbridge Configuration
Use the Southbridge Configuration menu (BIOS Menu 17) to configure the Southbridge
chipset.
Page 86
WAFER-BT-i1
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Chipset
Auto Power Button Status
[Disabled(ATX)]
Restore AC Power Loss
[Last State]
EUP Disable/Enable.
> PCI Express Configuration
--------------------: Select Screen
[Enabled]
 : Select Item
Enter Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
Audio Configuration
Audio Controller
BIOS Menu 17: Southbridge Chipset Configuration

Restore on AC Power Loss [Last State]
Use the Restore on AC Power Loss BIOS option to specify what state the system
returns to if there is a sudden loss of power to the system.

Power Off
The system remains turned off

Power On
The system turns on

Last State
DEFAULT
The system returns to its previous state. If it was on, it
turns itself on. If it was off, it remains off.

Audio Controller [Enabled]
Use the Audio Controller option to enable or disable the High Definition Audio controller.

Disabled

Enabled
The onboard High Definition Audio controller is disabled
DEFAULT
The onboard High Definition Audio controller is detected
automatically and enabled
Page 87
WAFER-BT-i1
5.4.2.1 PCI Express Configuration
Use the PCI Express Configuration menu (BIOS Menu 17) to configure the PCI
Express.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Advanced
PCI Express Configuration
PCI Express Port 0
Speed
[Enabled]
[Auto]
PCI Express Port 1
Speed
[Enabled]
[Auto]
PCI Express Port 2
Speed
[Enabled]
[Auto]
PCI Express Port 3
Speed
[Enabled]
[Auto]
Enable or Disable the PCI
Express Port 0 in the
Chipset.
--------------------: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 18: Console Redirection Settings

PCI Express Port [Enabled]
Use the PCI Express Port option to enable or disable the PCI Express port.


Disabled

Enabled
Disables the PCI Express port.
DEFAULT
Enables the PCI Express port.
Speed [Auto]
Use the Speed option to configure PCIe port speed.

Auto
Configure PCIe port speed to auto

Gen 2
Configure PCIe port speed to Gen2

Gen 1
Configure PCIe port speed to Gen1
Page 88
WAFER-BT-i1
5.5 Security
Use the Security menu (BIOS Menu 19) to set system and user passwords.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Password Description
If ONLY the Administrator’s password is set,
then this only limits access to Setup and is
only asked for when entering Setup
If ONLY the User’s password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will
have Administrator rights.
The password length must be:
Minimum length
3
Maximum length
20
Administrator Password
User Password
Set Setup Administrator
Password
--------------------: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 19: Security

Administrator Password
Use the Administrator Password to set or change a administrator password.

User Password
Use the User Password to set or change a user password.
Page 89
WAFER-BT-i1
5.6 Boot
Use the Boot menu (BIOS Menu 17) to configure system boot options.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Boot Configuration
Bootup NumLock State
Quiet Boot
Option ROM Messages
UEFI Boot
Launch PXE OpROM
[On]
[Enabled]
[Force BIOS]
[Disabled]
[Disabled]
Select the keyboard
NumLock state
--------------------: Select Screen
 : Select Item
Boot Option Priorities
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 20: Boot

Bootup NumLock State [On]
Use the Bootup NumLock State BIOS option to specify if the number lock setting must
be modified during boot up.

On
DEFAULT
Allows the Number Lock on the keyboard to be
enabled automatically when the computer system
boots up. This allows the immediate use of the
10-key numeric keypad located on the right side of
the keyboard. To confirm this, the Number Lock LED
light on the keyboard is lit.

Off
Does not enable the keyboard Number Lock
automatically. To use the 10-keys on the keyboard,
press the Number Lock key located on the upper
left-hand corner of the 10-key pad. The Number
Lock LED on the keyboard lights up when the
Number Lock is engaged.
Page 90
WAFER-BT-i1

Quiet Boot [Enabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.


Disabled

Enabled
Normal POST messages displayed
DEFAULT
OEM Logo displayed instead of POST messages
Option ROM Messages [Force BIOS]
Use the Option ROM Messages option to set the Option ROM display mode.

Force
DEFAULT
Sets display mode to force BIOS.
BIOS

Sets display mode to current.
Keep
Current

UEFI Boot [Disabled]
Use the UEFI Boot option to enable or disable to boot from the UEFI devices.

If the first boot HDD is GPT then enable UEFI boot
Auto
options, otherwise disable,


Enabled

Disabled
Boot from UEFI devices is enabled.
DEFAULT
Boot from UEFI devices is disabled.
Launch PXE OpROM [Disabled]
Use the Launch PXE OpROM option to enable or disable boot option for legacy network
devices.

Disabled

Enabled
DEFAULT
Ignore all PXE Option ROMs
Load PXE Option ROMs.
Page 91
WAFER-BT-i1

Boot Option Priority
Use the Boot Option Priority function to set the system boot sequence from the available
devices. The drive sequence also depends on the boot sequence in the individual device
section.
5.7 Exit
Use the Exit menu (BIOS Menu 21) to load default BIOS values, optimal failsafe values
and to save configuration changes.
Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.
Main
Advanced Chipset Security
Boot
Save & Exit
Save Changes and Reset
Discard Changes and Reset
Reset the system after
saving the changes.
Restore Defaults
Save as User Defaults
Restore User Defaults
--------------------: Select Screen
 : Select Item
Enter Select
F1
General Help
F2
Previous Values
F3
Optimized
Defaults
F4
Save
ESC
Exit
Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc.
BIOS Menu 21:Exit

Save Changes and Reset
Use the Save Changes and Reset option to save the changes made to the BIOS options
and to exit the BIOS configuration setup program.

Discard Changes and Reset
Use the Discard Changes and Reset option to exit the system without saving the
changes made to the BIOS configuration setup program.
Page 92
WAFER-BT-i1

Restore Defaults
Use the Restore Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F3 key can be used for this operation.

Save as User Defaults
Use the Save as User Defaults option to save the changes done so far as user defaults.

Restore User Defaults
Use the Restore User Defaults option to restore the user defaults to all the setup options.
Page 93
WAFER-BT-i1
Appendix
A
A Regulatory Compliance
Page 94
WAFER-BT-i1
DECLARATION OF CONFORMITY
This equipment has been tested and found to comply with specifications for CE marking.
If the user modifies and/or installs other devices in the equipment, the CE conformity
declaration may no longer apply.
FCC WARNING
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Page 95
WAFER-BT-i1
Appendix
B
B BIOS Menu Options
Page 96
WAFER-BT-i1
System Date [xx/xx/xx] ........................................................................................................65
System Time [xx:xx:xx] .......................................................................................................65
ACPI Sleep State [S3 only (Suspend to RAM)] .................................................................66
Serial Port [Enabled]............................................................................................................68
Change Settings [Auto] .......................................................................................................68
Serial Port [Enabled]............................................................................................................68
Change Settings [Auto] .......................................................................................................69
Serial Port [Enabled]............................................................................................................69
Change Settings [Auto] .......................................................................................................69
Serial Port [Enabled]............................................................................................................70
Change Settings [Auto] .......................................................................................................70
PC Health Status ..................................................................................................................72
CPU Smart Fan control [Auto PWM Mode]........................................................................73
Temperature of Off [75] .......................................................................................................73
Temperature of Start [80 .....................................................................................................74
Start PWM [30]......................................................................................................................74
Slope (Duty Cycle) [4]..........................................................................................................75
Wake system with Fixed Time [Disabled]..........................................................................76
Console Redirection [Disabled] .........................................................................................77
Terminal Type [ANSI]...........................................................................................................78
Bits per second [115200].....................................................................................................78
Data Bits [8] ..........................................................................................................................79
Parity [None].........................................................................................................................79
Stop Bits [1] ..........................................................................................................................79
Intel® Virtualization Technology [Disabled]......................................................................80
EIST [Enabled]......................................................................................................................80
SATA Mode [ACHI Mode] ....................................................................................................81
Serial-ATA Port 1/0 [Enabled] .............................................................................................81
SATA Port 1/0 HotPlug [Disabled]......................................................................................82
USB Devices .........................................................................................................................82
Legacy USB Support [Enabled]..........................................................................................83
Memory Information ............................................................................................................85
DVMT Pre-Allocated [256MB]..............................................................................................85
DVMT Total Gfx Mem [MAX]................................................................................................86
Page 97
WAFER-BT-i1
Primary IGFX Boot Display [VBIOS Default] .....................................................................86
Restore on AC Power Loss [Last State] ............................................................................87
Audio Controller [Enabled] .................................................................................................87
PCI Express Port [Enabled] ................................................................................................88
Speed [Auto].........................................................................................................................88
Administrator Password .....................................................................................................89
User Password .....................................................................................................................89
Bootup NumLock State [On]...............................................................................................90
Quiet Boot [Enabled] ...........................................................................................................91
Option ROM Messages [Force BIOS].................................................................................91
UEFI Boot [Disabled] ...........................................................................................................91
Launch PXE OpROM [Disabled] .........................................................................................91
Boot Option Priority.............................................................................................................92
Save Changes and Reset ....................................................................................................92
Discard Changes and Reset ...............................................................................................92
Restore Defaults ..................................................................................................................93
Save as User Defaults .........................................................................................................93
Restore User Defaults .........................................................................................................93
Page 98
WAFER-BT-i1
Appendix
C
C Terminology
Page 99
WAFER-BT-i1
AC ’97
Audio Codec 97 (AC’97) refers to a codec standard developed by
Intel® in 1997.
ACPI
Advanced Configuration and Power Interface (ACPI) is an OS-directed
configuration, power management, and thermal management interface.
AHCI
Advanced Host Controller Interface (AHCI) is a SATA Host controller
register-level interface.
ATA
The Advanced Technology Attachment (ATA) interface connects
storage devices including hard disks and CD-ROM drives to a
computer.
APM
The Advanced Power Management (APM) application program
interface (API) enables the inclusion of power management in the
BIOS.
ARMD
An ATAPI Removable Media Device (ARMD) is any ATAPI device that
supports removable media, besides CD and DVD drives.
ASKIR
Amplitude Shift Keyed Infrared (ASKIR) is a form of modulation that
represents a digital signal by varying the amplitude (“volume”) of the
signal. A low amplitude signal represents a binary 0, while a high
amplitude signal represents a binary 1.
BIOS
The Basic Input/Output System (BIOS) is firmware that is first run when
the computer is turned on and can be configured by the end user
CODEC
The Compressor-Decompressor (CODEC) encodes and decodes
digital audio data on the system.
CMOS
Complimentary metal-oxide-conductor is a type of integrated circuit
used in chips like static RAM and microprocessors.
COM
COM is used to refer to serial ports. Serial ports offer serial
communication to expansion devices. The serial port on a personal
Page 100
WAFER-BT-i1
computer is usually a male DE-9 connector.
DAC
The Digital-to-Analog Converter (DAC) converts digital signals to
analog signals.
DDR
Double Data Rate refers to a data bus transferring data on both the
rising and falling edges of the clock signal.
DMA
Direct Memory Access (DMA) enables some peripheral devices to
bypass the system processor and communicate directly with the
system memory.
DIMM
Dual Inline Memory Modules are a type of RAM that offer a 64-bit data
bus and have separate electrical contacts on each side of the module.
EHCI
The Enhanced Host Controller Interface (EHCI) specification is a
register-level interface description for USB 2.0 Host Controllers.
GbE
Gigabit Ethernet (GbE) is an Ethernet version that transfers data at 1.0
Gbps and complies with the IEEE 802.3-2005 standard.
2
GPIO
General purpose input
IrDA
Infrared Data Association (IrDA) specify infrared data transmission
protocols used to enable electronic devices to wirelessly communicate
with each other.
L1 Cache
The Level 1 Cache (L1 Cache) is a small memory cache built into the
system processor.
L2 Cache
The Level 2 Cache (L2 Cache) is an external processor memory cache.
LVDS
Low-voltage differential signaling (LVDS) is a dual-wire, high-speed
differential electrical signaling system commonly used to connect LCD
displays to a computer.
MAC
The Media Access Control (MAC) protocol enables several terminals or
network nodes to communicate in a LAN, or other multipoint networks.
Page 101
WAFER-BT-i1
PCIe
PCI Express (PCIe) is a communications bus that uses dual data lines
for full-duplex (two-way) serial (point-to-point) communications between
the SBC components and/or expansion cards and the SBC chipsets.
Each line has a 2.5 Gbps data transmission rate and a 250 MBps
sustained data transfer rate.
POST
The Power-on Self Test (POST) is the pre-boot actions the system
performs when the system is turned-on.
QVGA
Quarter Video Graphics Array (QVGA) refers to a display with a
resolution of 320 x 240 pixels.
RAM
Random Access Memory (RAM) is a form of storage used in computer.
RAM is volatile memory, so it loses its data when power is lost. RAM
has very fast data transfer rates compared to other storage like hard
drives.
SATA
Serial ATA (SATA) is a serial communications bus designed for data
transfers between storage devices and the computer chipsets. The
SATA bus has transfer speeds up to 1.5 Gbps and the SATA 3Gb/s bus
has data transfer speeds of up to 3.0 Gbps.
S.M.A.R.T
Self Monitoring Analysis and Reporting Technology (S.M.A.R.T) refers
to automatic status checking technology implemented on hard disk
drives.
UART
Universal Asynchronous Receiver-transmitter (UART) is responsible for
asynchronous communications on the system and manages the
system’s serial communication (COM) ports.
UHCI
The Universal Host Controller Interface (UHCI) specification is a
register-level interface description for USB 1.1 Host Controllers.
USB
The Universal Serial Bus (USB) is an external bus standard for
interfacing devices. USB 1.1 supports 12Mbps data transfer rates, while
Page 102
WAFER-BT-i1
USB 2.0 supports 480Mbps data transfer rates.
VGA
The Video Graphics Array (VGA) is a graphics display system
developed by IBM.
Page 103
WAFER-BT-i1
Appendix
D
D Digital I/O Interface
Page 104
WAFER-BT-i1
D.1 Introduction
The DIO connector on the WAFER-BT-i1 is interfaced to GPIO ports on the Super I/O
chipset. The DIO has both 8-bit digital inputs and 8-bit digital outputs. The digital inputs
and digital outputs are generally control signals that control the on/off circuit of external
devices or TTL devices. Data can be read or written to the selected address to enable the
DIO functions.
NOTE:
For further information, please refer to the datasheet for the Super I/O
chipset.
The BIOS interrupt call INT 15H controls the digital I/O.
INT 15H:
AH – 6FH
Sub-function:
AL – 8
:Set the digital port as INPUT
AL
:Digital I/O input value
Page 105
WAFER-BT-i1
D.2 Assembly Language Sample 1
MOV
AX, 6F08H
INT
15H
;setting the digital port as input
;
AL low byte = value
AH – 6FH
Sub-function:
AL – 9
:Set the digital port as OUTPUT
BL
:Digital I/O input value
D.3 Assembly Language Sample 2
MOV
AX, 6F09H
MOV
BL, 09H
INT
15H
Digital Output is 1001b
Page 106
;setting the digital port as output
;digital value is 09H
;
WAFER-BT-i1
Appendix
E
E Watchdog Timer
Page 107
WAFER-BT-i1
NOTE:
The following discussion applies to DOS. Contact IEI support or visit the IEI
website for drivers for other operating systems.
The Watchdog Timer is a hardware-based timer that attempts to restart the system when it
stops working. The system may stop working because of external EMI or software bugs.
The Watchdog Timer ensures that standalone systems like ATMs will automatically
attempt to restart in the case of system problems.
A BIOS function call (INT 15H) is used to control the Watchdog Timer.
INT 15H:
AH – 6FH Sub-function:
AL – 2:
Sets the Watchdog Timer’s period.
BL:
Time-out value (Its unit-second is dependent on the item “Watchdog
Timer unit select” in CMOS setup).
Table E-1: AH-6FH Sub-function
Call sub-function 2 to set the time-out period of Watchdog Timer first. If the time-out value
is not zero, the Watchdog Timer starts counting down. When the timer value reaches zero,
the system resets. To ensure that this reset condition does not occur, calling sub-function
2 must periodically refresh the Watchdog Timer. However, the watchdog timer is disabled
if the time-out value is set to zero.
A tolerance of at least 10% must be maintained to avoid unknown routines within the
operating system (DOS), such as disk I/O that can be very time-consuming.
Page 108
WAFER-BT-i1
NOTE:
The Watchdog Timer is activated through software. The software
application that activates the Watchdog Timer must also deactivate it
when closed. If the Watchdog Timer is not deactivated, the system will
automatically restart after the Timer has finished its countdown.
EXAMPLE PROGRAM:
; INITIAL TIMER PERIOD COUNTER
;
W_LOOP:
;
MOV
AX, 6F02H
;setting the time-out value
MOV
BL, 30
;time-out value is 48 seconds
INT
15H
;
; ADD THE APPLICATION PROGRAM HERE
;
CMP
JNE
EXIT_AP, 1
W_LOOP
MOV
AX, 6F02H
MOV
BL, 0
INT
;is the application over?
;No, restart the application
;disable Watchdog Timer
;
15H
;
; EXIT ;
Page 109
WAFER-BT-i1
Appendix
F
F Hazardous Materials
Disclosure
Page 110
WAFER-BT-i1
F.1 Hazardous Material Disclosure Table for IPB Products
Certified as RoHS Compliant Under 2002/95/EC Without
Mercury
The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain materials in the product, and is applicable to China
RoHS only.
A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.
Please refer to the table on the next page.
Page 111
WAFER-BT-i1
Part Name
Toxic or Hazardous Substances and Elements
Lead
Mercury
Cadmium
Hexavalent
Polybrominated
Polybrominated
(Pb)
(Hg)
(Cd)
Chromium
Biphenyls
Diphenyl Ethers
(CR(VI))
(PBB)
(PBDE)
Housing
O
O
O
O
O
O
Display
O
O
O
O
O
O
Printed Circuit
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Fan Assembly
O
O
O
O
O
O
Power Supply
O
O
O
O
O
O
O
O
O
O
O
O
Board
Metal
Fasteners
Cable
Assembly
Assemblies
Battery
O: This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below
the limit requirement in SJ/T11363-2006
X: This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part
is above the limit requirement in SJ/T11363-2006
Page 112
WAFER-BT-i1
此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。
本产品上会附有”环境友好使用期限”的标签,此期限是估算这些物质”不会有泄漏或突变”的
年限。本产品可能包含有较短的环境友好使用期限的可替换元件,像是电池或灯管,这些元
件将会单独标示出来。
部件名称
有毒有害物质或元素
铅
汞
镉
六价铬
多溴联苯
多溴二苯醚
(Pb)
(Hg)
(Cd)
(CR(VI))
(PBB)
(PBDE)
壳体
O
O
O
O
O
O
显示
O
O
O
O
O
O
印刷电路板
O
O
O
O
O
O
金属螺帽
O
O
O
O
O
O
电缆组装
O
O
O
O
O
O
风扇组装
O
O
O
O
O
O
电力供应组装
O
O
O
O
O
O
电池
O
O
O
O
O
O
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
Page 113
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement