Sharp | FO-5500 | Service manual | Sharp FO-5500 Service manual

Sharp FO-5500 Service manual
FO-5500U/C
SERVICE MANUAL
No. 00ZFO5500USME
FACSIMILE
MODEL
FO-5500
This service manual FO-5500U/C is applied to the optional type (FO-45UC) equipped with the 3rd transport unit of FO6500U/C. The performance and operation are not different from the old ones. Since only the areas which are changed
from those of FO-6500U/C are described, use the existing service manual (00ZFO6500USME) of FO-6500U/C together
for the other areas.
CAUTION
This laser printer is a class 1 laser product that complies with 21CFR 1040.10 and 1040.11 of the CDRH standard. This means
that this machine does not produce a hazardous laser radiation. The use of controls, adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved on the eyes retina, there is
danger of spot damage to the retina.
The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of servicing.
1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a unit, not an individual part.
2) Do not look into the machine with the main switch turned on after removing the toner/developer unit and drum cartridge.
3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected when removing and installing
the optical system.
4) The cover of Laser Printer Unit contains the safety interlock switch.
Do not defeat the safety interlock by inserting wedges or other items into the switch slot.
Laser Wave Length
: 770-810 mm
Laser Pulse Times
: 49.2 µs
Laser Output Power
: 0.5 mW
Parts marked with " " is important for maintaining the safety of the set. Be sure to replace these parts with specified
ones for maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
FO-5500U/C
CONTENTS
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[2] Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
[3] Transmittable Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
[4] Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
[5] Quick reference guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
CHAPTER 2. ADJUSTMENTS
[1] Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
[2] Diagnostics and service soft switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
[3] Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28
[4] Error code table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
CHAPTER 4. DIAGRAMS
[1] Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[2] Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
[3] Point to point diagram and connector signal name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT
[1] Control PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
[2] TEL/LIU PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
[3] Power supply PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16
[4] Operation panel PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
[5] CCD PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-21
[6] RS232C I/F PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22
[7] Printer control PWB circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24
PARTS GUIDE
Note: Since the following contents are the same as those of the base model FO-6500U/C, refer to the Service
Manual for the base model FO-6500U/C.
CONTENTS
CHAPTER 3. MECHANICAL DESCRIPTION
[1] Mechanical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
[2] Printer description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
[3] Disassembly/assembly procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
CHAPTER 5. CIRCUIT DESCRIPTION
[1] Circuit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[2] Circuit description of control PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[3] Circuit description of TEL/LIU PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
[4] Circuit description of CCD PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22
[5] Circuit description of operation PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22
[6] Circuit description of power supply PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23
[7] Circuit description of RS232C I/F PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28
CHAPTER 7. OPERATION FLOWCHART
[1] Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[2] Power on sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
CHAPTER 8. OTHERS
[1] Service Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
[2] IC signal name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
FO-5500U/C
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications
•
GENERAL
Effective scanning width:
10.1" (256 mm)
Effective recording width:
8.0" (203 mm)
Copy function:
Single/Multi-copy/Sort-copy
(99 copies/page)
Telephone function:
Standard (cannot be used if power
fails)
Applicable telephone
line:
Public switched telephone network/PBX
Compatibility:
ITU-T (CCITT) G3 mode
Configuration:
Half-duplex, desktop transceiver
Compression scheme:
MH, MR, MMR and Sharp special mode
Memory size*:
1 MB (approx. 50 average pages)
Halftone (gray scale):
64 levels
Memory option:
1 MB/2 MB/4 MB Flash Memory
Power requirements:
120 V AC, 60 Hz
Flat-bed, solid-state CCD
Operating environment:
50-86°F (10-30°C), 20 to 85% RH
Horizontal:
Power consumption:
Stand-by: 10 W at AC 120 V
Scanning method:
Resolution:
Maximum: 400 W at AC 120 V
203 lines/inch (8 dots/mm)
Dimensions:
Vertical:
Depth: 22.9" (582 mm)
Standard – 98 lines/inch (3.85
lines/mm)
Height: 13.7" (349 mm)
Weight:
Fine/Halftone – 196 lines/inch (7.7
lines/mm)
Super fine – 392 lines/inch (15.4
lines/mm)
Printing density:
•
Horizontal:
406 lines/inch (16 lines/mm)
391 lines/inch (15.4 lines/mm)
Auto/Manual switching
Modem speed:
14400 bps with automatic fallback to
12000, 9600, 7200, 4800, or 2400 bps
Transmission time*:
Type:
Desktop, Laser Beam Printer
Print system:
Electrostatic Dry Powdered Imaging
System
Exposure system:
Laser Diode + Polygon Mirror
Scanning
Resolution:
Horizontal: 406 (dot/inch)
Vertical: 391 (dot/inch)
Approx. 6 seconds
(Sharp special mode)
Input document size:
Automatic feeding:
Width – 5.8 to 10.1" (148 to 256 mm)
Print speed:
6 pages per minute (A4 size paper)
First print time:
Within 19 seconds (face down)
Warming-up time:
Within 40 sec.
Operating environment:
Temperature: 10-30˚C
Humidity: 20-80%RH
Length – 5.0 to 14.3" (128 to 364 mm)
Manual feeding:
Width – 5.8 to 11.0" (148 to 280 mm)
Length – 5.0 to 17.0" (128 to 432 mm)
Paper size:
Approx. 40.8 lbs. (18.5 kg)
PRINTER SECTION
Vertical:
Reception modes:
Width: 13.8" (351 mm)
Toner cartridge life:
3,000 prints or more (when black-towhite ratio on print is 5% or less)
Drum cartridge life:
20,000 prints or more (when blackto-white ratio on print is 5% or less)
Width – 8.5" (216 mm)
Length – 11-14" (280-356 mm)
Paper capacity:
650 sheets
Automatic document
feeder:
50 documents max.
* Based on ITU-T (CCITT) Test Chart #1 at standard resolution in
Sharp special mode, excluding time for protocol signals (i.e., ITUT phase C time only).
<IMPORTANT PLEASE READ FIRST>
To avoid problems with supplies, please don’t use supplies from other units. Please use new supplies, when supply changes are required.
1–1
FO-5500U/C
[2] Operation panel (1)
CHANGEOVER key
Two types of information appear in the display: prompts related to
operations you are performing, and information about how the fax
is using the telephone line (transmitting, receiving, etc.). Press this
key to switch between the two types of information.
LINE STATUS light
This lights when the fax machine
is using the telephone line.
Display
This displays various
messages during
operation and
programming.
LINE-STATUS
IN USE
Service indicator
This lights when a
problem occurs which
must be fixed by a
service engineer.
Drum cartridge indicator
This blinks when the drum
cartridge nears the end of
its life, and lights steadily
when the drum cartridge
needs replacement.
RESOLUTION
STANDARD
FINE
SUPER FINE
HALF TONE
CHANGEOVER
RESOLUTION key
Press this key to
adjust the resolution
before sending or
copying a document.
Toner cartridge indicator
This blinks when toner nears
empty, and lights steadily
when the toner/developer
cartridge needs replacement.
Paper out indicator
This blinks when one of the
paper sources (cassette) is out
of paper, and lights steadily when
all sources are out of paper.
FUNCTION key
SPEED DIAL key
Press this key to dial Press this key to select
a Speed Dial number. various special functions.
BROADCAST key
Press this key to send a
document to a group of
receiving fax machines.
Telephone dial keypad
(numeric keys)
Use these keys to dial
and program numbers.
REPORT key
Press this key to print out
a report on the transaction
just completed.
COPY key
Press this key to make
a copy of a document.
ABC
1
GHI
MNO
5
COPY
REPORT
DOCUMENT
SPEED DIAL
BROADCAST COVER SHEET PRIORITY
6
TUV
7
FUNCTION
3
JKL
4
PRS
DEF
2
DOCUMENT key
Press this key to transmit
a document without
reading it into memory.
WXY
8
REDIAL
9
OPER
SPEAKER
STOP
START
0
REDIAL key
Press this key to automatically
redial the last number dialed.
SPEAKER key
Press this key to dial a
number without picking
up the handset.
STOP key
Press this key to
stop operations
before they are
completed.
COVER SHEET key
Press this key to include
a cover sheet with a
transmitted document.
1–2
START key
Press this key to
send or receive
a document.
PRIORITY key
Press this key when
you want to transmit
a document ahead of
other documents which
are waiting in memory
for transmission.
FO-5500U/C
Operation panel (2)
RELAY key
Press this key to send a document
to another fax machine and have
that machine in turn send the
document to a number of end
receiving machines.
PAGE COUNTER key
Press this key to have a slash and
the total number of pages added
after each page number on the
pages of a transmitted document.
Rapid Dial keys
Press one of these keys to dial a fax
or voice number automatically. (these
keys also serve as letter entry keys
when storing a name).
TIMER key
Press this key to set an
operation to be performed
automatically at a later time.
LIFE key
Press this key, followed
by the "1" key, to check
the total number of pages
printed by the fax machine.
CONFIDENTIAL key
Press this key to send or
print out a confidential
document.
CONTRAST key
Press this key to adjust the
contrast before sending or
copying a document.
MEM. STATUS key
Press this key to
see what documents
have been scanned
into memory for
transmission.
01
02
03
04
05
06
07
08
33
34
35
36
37
38
39
A
B
C
D
E
F
G
H
A
B
C
D
E
F
G
H
09
10
11
12
13
14
15
16
41
42
43
44
45
46
47
48
J
K
L
M
N
O
P
I
J
K
L
M
N
O
P
I
17
18
19
20
21
22
23
24
CONTRAST PAGE COUNTERCONFIDENTIAL TIMER
RELAY
Q
U
Q
R
S
T
U
V
W
X
25
26
27
28
29
30
31
32
Y
Z
SHIFT
SP
CLEAR
CLEAR key
Press this key to clear
mistakes when storing
names and numbers.
SP key
Press this key to enter
symbols when storing
a name.
SHIFT key
Press this key to switch
between upper and
lower case when storing
a name.
T
V
key, key
Press these keys to move
the cursor forward and
backward when storing
names and numbers.
1–3
MEM.STATUS SEARCH DIAL
W
DOWN
X
UP
Z
SPACE
(Flip up the
Rapid Key
overlay)
SPACE key
Press this key to enter a
space when storing a name.
S
DUPLEX SCAN
Y
SPACE
R
LIFE
40
SHIFT
SP
CLEAR
DUPLEX SCAN key
Press this key to transmit
or copy two-sided
documents.
UP and DOWN key
Press these keys to adjust
the volume of the handset
when the handset is lifted,
the volume of the speaker
when the SPEAKER key
has been pressed, or the
volume of the ringer at all
other times.
SEARCH DIAL key
Press this key to
search by name for
a number stored
for automatic
dialing.
FO-5500U/C
4. Cautions on Transmitting Documents
• Documents written in yellow, greenish yellow, or
[3] Transmittable documents
Normal size
width
5.83" – 8.5" (148 – 216 mm)
length
5.04" – 11" (128 – 279 mm)
(Max.)
432mm
(Max.)
Letter size 279mm
(Min.)
•
Ink, glue, and correcting fluid on documents must be dry before the
documents can be transmitted.
•
All clips, staples and pins must be removed from documents before transmission.
•
Patched (taped) documents should be copied first on a copier and
then the copies used for transmission.
•
All documents should be fanned before insertion into the feeder to
prevent possible double feeds.
5. Automatic Document Feeder Capacity
128mm
148mm
216mm
[Normal size]
Number of pages that can be placed into the feeder at anytime is as
follows:
216mm
[Special size]
Normal size: max. 50 sheets (14 lbs – 20 lbs)
Use document carrier sheet for smaller documents.
*
Special size: single sheet only (manual feed)
With special sizes, only one sheet can be fed into the machine at
a time. Insert next page into feeder as current page is being
scanned.
NOTES:
2. Paper Thickness & Weight
Product specifications
Indication
Weight
indication
Thickness
indication
Lower Limit
Upper Limit
Japanese indication
Size 4 × 6
45kg paper
70kg paper
Metric system
indication
52g/m2
80g/m2
American indication
LB system indication
14 LB
20 LB
Metric system
indication
0.06mm
0.1mm
Inch system indication 0.0024"
Document
size
light blue ink
cannot be transmitted.
1. Document Sizes
Document size
Range
•
When you need to send or copy more pages than the
feeder limit, place additional pages in feeder when last
page in feeder is being scanned.
•
Place additional pages carefully and gently in feeder.
If force is used, double-feeding or a document jam may
result.
6. Readable Width & Length
The readable width and length of a document are slightly smaller than
the actual document size.
Note that characters or graphics outside the effective document scanning range will not be read.
•
Readable width
8.3" (208 mm) max.
0.0035"
(148mm × 128mm) ~
W letter (279.4mm × 432mm)
A4 (210mm × 297mm)
Letter (216mm × 279mm)
Number of Document size
ADF sheets Weight
Paper
quality
Kind
B6 ~ Letter/A4 size
50 sheets
B4 size/Legal
20 sheets
W letter size
1 sheet
90 kg (104g/m2) or more
135 kg (157g/m2) or less
1 sheet
Readable width
•
Paper of fine quality/bond paper/Kent
paper
4mm
3. Document Types
• Normal paper
Documents handwritten in pencil (No. 2 lead or softer), fountain
pen, ball point pen, or felt-tipped pen can be transmitted.
Documents of normal contrast duplicated by a copying machine
can also be transmitted.
•
Diazo copy (blueprint)
Diazo copy documents of a normal contrast may be transmitted.
•
Carbon copy
A carbon copy may be transmitted if its contrast is normal.
Readable length
This is the length of the document sent minus 0.16" (4 mm) from the
top and bottom edges.
Readable length
4mm
1–4
FO-5500U/C
7. Use of Document Carrier Sheet
TELEPHONE JACK
A document carrier sheet must be used for the following documents.
A standard RJ11C telephone jack must be located near the machine.
This is the telephone jack commonly used in most homes and offices.
•
•
•
Those with tears.
•
Those smaller than size 5.83" (W) × 5.04" (L) (148 mm (W) × 128
mm (L)).
Carbon-backed documents
If the machine is moved from a cold to a warm place...
If the machine is moved from a cold to a warm place, it is possible
that the reading glass may fog up, preventing proper scanning of
documents for transmission. To remove the fog, turn on the power
and wait approximately 2 hours before using the machine.
Make print straight
across paper
E.G.
Place the document
carrier in the document
feeder with the clear film
side down
2. Installing the printer cartridges (Toner
cartridge: FO-45ND/Drum cartridge: FO-45DR)
1 Press the button on the side of the printer compartment, and open
Direction of insertion
the printer cover.
NOTE: To transmit a carbon-backed document, insert a white
sheet of paper between the carbon back of the document
and the document carrier.
•
Those containing an easily separable writing substance (e.g., tracing paper written on with a soft, heavy lead pencil).
NOTES:
•
•
When using the document carrier, carefully read the instructions written on the back.
•
If the document carrier is dirty, clean it with a soft, moist
cloth, and then dry it before using for transmission.
•
Do not place more than one document in the carrier at a
time.
Plugging the fax machine into a jack which is not an RJ11C jack
may result in damage to the machine or your telephone system. If
you do not know what kind of jack you have, or need to have one
installed, contact the telephone company.
•
Caution! The ribs on the bottom of the inside of the printer
cover become very hot during printing. Be careful not to touch
them.
•
If you are installing the cartridges for the first time, go to Step 4.
The thickness of document which can be held with the carrier
sheet is up to 20 lb.
2 If you are replacing the cartridges, grasp the handle on the toner
cartridge, and pull the toner cartridge out of the compartment.
[4] Installation
•
If you are only replacing the drum cartridge, place the toner
cartridge on a piece of paper on a horizontal surface.
•
If you are only replacing the toner cartridge, go to Step 6.
1. Site selection
Take the following points into consideration when selecting a site for
this model.
ENVIRONMENT
•
•
The machine must be installed on a level surface.
•
Provide easy access to the front, back, and sides of the machine.
In particular, keep the area in front of the machine clear, or the
original document may jam as it comes out after scanning.
•
•
The temperature should be between 41° and 95°F (10° and 35°C).
Keep the machine away from air conditioners, heaters, direct sunlight, and dust.
The humidity should be between 30% and 85% (without condensation).
3 Pull the old drum cartridge out of the compartment.
ELECTRICITY
A 120 V, 60 Hz, grounded (3-prong) AC outlet is required.
Caution!
•
Connection to a power source other than that specified will cause
damage to the equipment and is not covered under the warranty.
•
If your area experiences a high incidence of lightning or power
surges, we recommend that you install a surge protector for the
power and telephone lines. Surge protectors can be purchased at
most telephone specialty stores.
1–5
FO-5500U/C
4 Remove the new drum cartridge from its packaging.
9 If you replaced the toner cartridge, reset the toner counter by
pressing the LIFE key (flip up the Rapid Key overlay if necessary),
the "2" key, and the START key.
LIFE
right side is marked "R") with the arrowhead pointing down which
is marked on the right side of the compartment, and insert the
cartridge into the compartment so that the ends of the cartridge
move along the guides on the sides of the compartment. Make
sure the cartridge is set firmly in place.
•
2
V
5 Align the arrowhead on the right side of the drum cartridge (the
•
START
F If you replaced the drum cartridge, reset the drum counter by
pressing the LIFE key (flip up the Rapid Key overlay if necessary),
the "3" key, and the START key.
Place the old drum cartridge (if you removed one) in the empty
drum cartridge bag, seal the bag, and dispose of it in a way that
conforms to any local regulations that may exist in your area.
LIFE
If you are not replacing the toner cartridge, go to Step 7.
START
3
V
L
R1
Left
Right
3. Assembly and connections
1 Connect the handset cord to the handset and the fax as shown.
•
6 Remove the new toner cartridge from its packing, and shake sev-
Place the handset on the handset rest.
eral times as shown.
•
This ensures that the toner is well distributed inside the cartridge.
7 Hold the handle of the toner cartridge so that the "2" marked on
Use the handset to make ordinary
phone calls, or to transmit and receive documents manually.
the cartridge is to the right, and insert the cartridge into the compartment so that the two knobs on each side of the cartridge move
along the two guides on each side of the compartment.
Press the handle down so that the cartridge sets into place.
•
The ends of the handset cord are identical, so they will go into
either jack.
2 Plug one end of the telephone line cord into the jack on the fax
marked "LINE". Plug the other end into a standard (RJ11C) telephone wall jack.
Place the old toner cartridge (if you removed one) in the empty
toner cartridge bag, seal the bag, and dispose of it in a way that
conforms to any local regulations that may exist in your area.
2
Left
Right
8 Close the printer cover.
TEL.
LINE
1–6
FO-5500U/C
3 Plug the power cord into a 120V, 60Hz, grounded (3-prong) AC
6 Insert the male end of the PC interface cable into the port on the
outlet.
right side of fax as shown. Tighten the attached screws with a
screwdriver.
Press the power switch to turn on the power.
7 Insert the female end of the PC interface cable into the serial
4 Attach the original document OUT tray by inserting the tabs into
(RS-232C) port on your computer.
Tighten the attached screws with a screwdriver.
the holes in the fax as shown.
5 Attach the received document tray by inserting the tabs into the
holes in the fax as shown.
4. Loading printing paper
The paper cassettes and the paper tray hold the paper on which
received documents are printed. If needed, a second cassette is
available as an option from your dealer.
The paper cassette can hold 500 sheets of either legal or letter size
paper. The paper tray can hold 150 sheets of either legal or letter size
paper.
1 Grasp the hand hold on the cassette as shown, lift the cassette
slightly, and then pull it out as far as it will go. Do not force.
Push down on green levers on both sides of the cassette tray as
shown, and then pull it completely out of the fax using both hands.
1–7
FO-5500U/C
2 Pinch the ends of the paper guide together, and move the guide to
7 Move the paper guide to the appropriate position depending on
the appropriate position depending on whether you are loading
letter or legal size paper.
whether you are loading letter or legal paper.
•
To remove the paper guide, press its inner side at the arrow
marks and lift.
LETTER
LEGAL
LT
R
LG
L
3 Place a stack of paper on the pressure plate, press it down, and
8 Place the paper in the tray.
insert the two far corners of the paper under the paper holders as
shown.
•
Make sure the stack of paper is not higher than the tabs at the
top of the paper guide. If it is, remove some of the paper.
9 Close the original document IN tray.
4 Put the cassette back in the fax.
•
Push down on green levers on sides of cassette for it to go all
the way in.
F If desired, attach a letter or legal sticker as appropriate to the fax
as shown.
5 If desired, attach a letter or legal sticker as appropriate to the
cassette.
6 Rotate the received document tray back. Grasp the hand hold on
the original document IN tray as shown, and open it.
1–8
FO-5500U/C
5 Replace the drum cartridge, and then the toner cartridge.
5. Clearing paper jams
If a document doesn’t feed through the scanner properly during transmission or copying, or DOCUMENT JAM appears in the display, first
try pressing the START key. If the document doesn’t come out of the
feeder, open the operation panel by squeezing the operation panel
release on the right side of the operation panel (marked "PULL UP"),
and gently pull out document.
L
R1
Left
1
Right
2
Left
Right
6 Close the printer cover.
2 If the leading edge of the document is protruding from the printer
compartment outlet, try pulling it out.
•
If you are unable to clear the paper jam in this way, continue
with the following steps.
7 If you didn’t find any paper in the printer compartment, or if
3 Open the printer cover and remove the toner cartridge and drum
cartridge.
PAPER JAM still appears in the display after you close the printer
cover, check each paper cassette and the paper tray.
•
•
Caution! The ribs on the bottom of the inside of the printer
cover become very hot during printing. Be careful not to touch
them.
4 Gently pull the paper out of the compartment.
•
•
To check the paper tray, grasp the hand hold on the original
document IN tray and rotate the tray up.
8 Gently pull out any jammed paper you find, and then replace the
If the leading edge of the paper has entered the fusing unit, first
pull the leading edge out of the fusing unit, then pull the paper
out of the compartment.
cassette or close the original document IN tray.
Be sure to remove any torn pieced of paper.
1–9
FO-5500U/C
6. Installing an option cassette (FO-45UC)
1 Remove the two screws on the rear side of the optional cassette,
and then remove the rear plate of the optional cassette.
2 Place the fax machine on top of the optional cassette. Connect the
connector on the optional cassette to the wire connector on the
bottom of the fax.
3 Replace the rear plate on the optional cassette, and secure it with
the two screws.
4 Secure the optional cassette to the fax machine with two screws
on the front and one screw on each side.
1 – 10
FO-5500U/C
[5] Quick reference guide
FUNCTION key menu
The following chart shows the layout of the functions and settings accessed by pressing the FUNCTION key. First press the FUNCTION key, the
appropriate numeric key as shown, and then "#" or " " until the desired item appears.
Instructions for making each setting appear in the display. If you have any difficulty, refer to the detailed instructions on the page shown below the
setting.
FUNCTION
1
Reception
Mode
4
3
2
Entry Mode
Optional Settings
Activity Report
Fax/Tel
Numbers for
Auto Dialing
Fine Resolution
Priority
Timer List
Telephone
Number List
Passcode Number
Relay Group List
Own Number and
Name Set
Passcode List
Option Setting
Program/Group
List
Batch
Transmission List
Department
Usage List
Date and Time
Set
7
6
Listing Mode
8
Print Hold
Mode
Program/Group
Mode
Retransmission
Times
Hold Data Print
Program Entry
Mode
Number of Rings to
Auto Answer Mode
Retransmission
Interval
Print Hold Code
Set
Auto Listing
Heater Mode
Print Hold Code
Clear
Transaction Report
Print Select
Junk Fax Check
Group Entry
Mode
Alarm Buzzer
Recall Times
Dial Mode
ID Number
Recall Wait Interval
Quick on Line
System Number
Security Selection
Store Junk Fax
Number
ECM
Multi TTI
Beep Length
Auto cover Sheet
Department
Code Mode
Confidential
Reception List
Anti Junk Fax
Number List
Tel. Billing Code
Memory Scanning
Copy Reduce
Department Code
Mode
Copy Cut-off
Distinctive Ringing
Receive Reduce
Verification Stamp
Image Memory
Print
Print Hold
PC-Interface Mode
Cassette Selection
Receive Unit
Cassette
Changeover
Note: Steps which are optional are enclosed in a dotted frame:
RESOLUTION
Transmitting documents
Normal Dialing (1)
Load
document
RESOLUTION
Lift handset
or
press SPEAKER
Dial (press
numeric keys)
START
Wait for
reception tone
Normal Dialing (2)
Lift handset
or
press SPEAKER
Hang up
Load
document
Dial (press
numeric keys)
RESOLUTION
START
Wait for
reception tone
Direct Keypad
Dialing
Hang up
START
Load
document
RESOLUTION
Dial (press
numeric keys)
Load
document
RESOLUTION
Press Rapid
key
Load
document
RESOLUTION
SPEED DIAL
Load
document
RESOLUTION
REDIAL
Rapid Key Dialing
Speed Dialing
Redialing
Enter Speed Dial number
(press numeric keys, -if less
than 3 digits, press START
to complete entry)
START
START
1 – 11
Wait for
reception tone
Serial Polling
Mode
9
Memory Polling
Mode
Memory Polling Set
Memory Polling
Clear
FO-5500U/C
MEMO
1 – 12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising