ZALMAN AMD Athlon 64 Socket 754 CPU Specifications

ZALMAN AMD Athlon 64 Socket 754 CPU Specifications
(English version)
CNPS7700 LED
Intel
Dual Core Pentium / Pentium 4
Socket 775 CPU
Grip (S-Type)
Intel Pentium 4
Socket 478 CPU
Grip (L-Type)
Inner Hole
AMD Sempron/AMD64
(Athlon 64 X2/Opteron/Athlon 64)
Socket 754/939/940 CPU
Grip (L-Type)
Outer Hole
* Please read before installation.
http://www.zalman.co.kr
http://www.zalmanusa.com
1. Features
1) Pure copper and/or pure aluminum base materials ensure excellent heat dissipation.
2)Supports Intel Dual Core Pentium / Pentium 4 (Socket 775), Intel Pentium 4 (Socket 478), AMD Athlon
64 X2 Dual Core, Sempron / AMD64 (Socket 754/939/940) for broad compatibility.
3) The large 120mm fan inside the FHS maximizes cooling performance by providing sufficient airflow
even at low fan speed.
4) The large 120mm fan provides air flow over a large area, cooling not only the CPU, but the VGA card,
Northbridge, FET, and RAM as well.
5) The high intensity red LEDs will operate with sufficient brightness even in low operating voltage.
6) The adjustable fan speed controller (FAM MATE 2) enables control of noise and fan performance.
2. Specifications
1) Cooler (CNPS7700 LED)
Model
Spec.
CNPS7700-AlCu LED
Materials
CNPS7700-Cu LED
Pure copper and pure aluminum
Weight
600(1)
918(1)
Thermal Resistance
0.19 ~ 0.28 ℃/W
0.17 ~ 0.24 ℃/W
136 (L) X 136 (W) X 67 (H) mm
Dimensions
Dissipation Area
3,268 ㎠
Bearing Type
2 Ball-Bearing
Fan Speed
1,000 ~ 2,000rpm ± 10% 2)
Noise Level
22.7 ~ 37.1dBA ± 10% 3)
Input Voltage
5 ~ 12V
2) FAN MATE 2
- Output Voltage : 5V ~11V 2%
- Power Consumption : 6W or lower
(Note 1) The maximum weight for a cooler is specified as 450g for Intel Socket 775/478 and AMD Socket
754/939/940. Special care should be taken when moving a computer equipped with a cooler
which exceeds the relevant weight limit. Zalman is not responsible for any damage that occurs
when moving a computer.
(Note 2) The cooler fan operates at 2,300rpm if connected directly to the motherboard’s power connector
without the use of FAN MATE 2.
(Note 3) Noise measured 1m distance away from source.
3. Exploded View
Fan
Grip (S-Type)
Grip (L-Type)
Fan Support
Clip
Fan Fixing Screw
FHS
Fan Support Fixing Screw
※
The specifications of any product may change without prior notice to improve performance.
1
4. Patents
Korean Patent No. 389257
Korean Patent Design No. 327440-3
Parents pending in over 20 nations around the world, including the USA, EU, and Japan
Precautions
1) Keep the product away from children.
2) Check to see that all components are present, and check the condition of the product and its components before
installation. If there is any problem, contact the place of purchase for a replacement.
3) If excessive force is exerted on the fan, the fan may malfunction and result in damage to the product and/or the
computer.
4) Do not insert your finger into the fan while it is operating.
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due to external causes, including but not
limited to, improper use, problems with electrical power, accident, neglect, alteration, repair,
improper installation, or improper testing.
5. Components
1) Common Components
❶ FHS Assembly (CNPS7700 LED)
❷ Four (4) Grips (2 each for S-Type and L-Type)
❸ Four (4) Bolts (for installing the FHS)
❹ Thermal Grease
❺ Fan Speed Controller (FAN MATE 2)
❻ Double - sided Tape (for installing FAN MATE 2)
❼ Cable for FAN MATE 2
❽ User’s Manual (in English and Korean)
❶
❷
2) Components for Intel Dual Core Pentium/Intel
Pentium 4 (Socket 775)
❾ One (1) Clip Support for Socket 775
❿ One (1) Backplate for Socket 775
Four (4) Clip Support Fixing Bolts
❸
❻
❹
❼
❺
❽
❾
❿
3) Components for Intel Pentium 4 (Socket 478)
Two (2) Clip Supports for Socket 478
4) Components for AMD Sempron / AMD64 (Socket 754/939/940)
Two (2) Nipples
One (1) Backplate for AMD64
One (1) set of Washers
※
The specifications of any product may change without prior notice to improve performance.
2
6. Compatible CPUs
1) Intel Dual Core Pentium / Pentium 4 - Socket 775
All CPUs conforming to Socket 775 platform
Caution)
① No components higher than 39mm (possible examples :
PSU, graphics card, RAM etc.) should be present within
a 68mm radius from the center of the CPU.
② For more information, please visit Zalman’s website
(http://www.zalman.co.kr) and click on the links of
"CNPS7700 Compatible Socket 775 Motherboards List".
2) Intel Pentium 4 - Socket 478
All CPUs conforming to Socket 478 platform
Caution)
① No components higher than 39mm (possible examples : PSU, graphics card, RAM etc.) should be present
within a 68mm radius from the center of the CPU.
② For Socket 478, as shown in Figure 2, a motherboard that is not compliant with the "10.2mm Motherboard
component height restriction" standard, introduced by Intel, may create interference between components
and the grip of CNPS7700 LED. Please do not install the CNPS7700 LED if this interference is observed.
10.2mm Motherboard component height restriction
Grip
Motherboard
Component
4mm
Motherboard Component
Figure 1
Compatible
Grip
Figure 2
Not Compatible
③ For more information, please visit Zalman’s website (http://www.zalman.co.kr) and click on the links of
"Compatibility between CNPS7700 and Socket 478 Pentium 4 Motherboards".
3) AMD Sempron / AMD64 - Socket 754/939/940
All CPUs conforming to Socket 754/939/940 platform
Caution)
① No components higher than 39mm (possible examples :
PSU, graphics card, RAM etc.) should be present within a
68mm radius from the center of the CPU.
② For more information, please visit Zalman’s website
(http://www.zalman.co.kr) and refer to “CNPS7700
Compatible Socket 754/939/940 Motherboards List” link.
※
The specifications of any product may change without prior notice to improve performance.
3
7. Installation
Socket
※ CNPS7700 LED must be used with a specific grip for
each CPU socket. Refer to the table on the right
to choose the correct grip.
Grip
Hole
775
S - Type
Hole
478
L - Type
Inner Hole
754/939/940
L - Type
Outer Hole
1) Intel Dual Core Pentium/Intel Pentium 4 - Socket 775
① Installation of Clip Support for Socket 775
Align the clip support for socket 775 and the backplate for socket 775 with the mounting holes on the motherboard
and fasten them together using the clip support fixing bolts. The lever slot on the clip support should be properly
oriented on the hinged side of the socket lever when installing.
※ The backplate support is used for the convenience of installation. You can remove it if it is not deemed necessary.
Clip Support Fixing Bolt
Clip Support for Socket 775
Socket Lever Hinge
Lever Slot
Motherboard
Socket Lever
Backplate for Socket 775
Lever Slot
Backplate Support
CPU (IHS)
② Thermal Grease Application
Clear off particles and residue from the top of the
CPU then spread a generous amount of the included
thermal grease thoroughly on top of the CPU.
Thermal Grease
※ Unlike the flat-milled base of the FHS, the top surface of the LGA775 CPU may have minute dips and peaks
causing pockets of non-contact between the FHS and CPU. Please apply a generous amount of thermal grease
on the top of the CPU.
③ Installation of Grips and Bolts
Grip (S-Type)
Bolt
Interlock the S-type grips with the clip. Insert the two
bolts into the holes of the grips.
④ FHS Placement
Set the FHS at the center of the CPU. Screw the bolts
in slightly, then tighten each bolt a few turns at a time while
alternating between the two until the Grips are completely
pressed against the Clip Support.
Grip (S-Type)
Clip Support for
Socket 775
⑤ Connect Power (Use FAN MATE 2)
◆ Please refer to FAN MATE 2 Installation and Usage on page 7.
※
The specifications of any product may change without prior notice to improve performance.
4
2) Intel Pentium 4 - Socket 478
① Thermal Grease Application
CPU (IHS)
Clear off particles and residue from the top of the
CPU then spread a thin layer of the included thermal
grease thoroughly on top of the CPU.
Thermal Grease
② Installation of Clip Supports for Socket 478
Install the clip supports for socket 478 on both sides
of the retention guide as shown in the diagram.
Retention Guide
Clip Support for Socket 478
③ Installation of Grips and Bolts
Interlock the L-type grips with the clip. Insert the two bolts
into the inner holes of the grips.
Bolt
Grip (L-Type)
Inner Hole
④ FHS Placement
Set the FHS at the center of the CPU. Screw the bolts
in slightly, and then tighten each bolt a few turns at a
time while alternating between the two until the Grips
are completely pressed against the Clip Support.
Grip (L-Type)
Clip Support for
Socket 478
⑤ Connect Power (Use FAN MATE 2)
◆ Please refer to FAN MATE 2 Installation and Usage on page 7.
※
The specifications of any product may change without prior notice to improve performance.
5
3) AMD Sempron/AMD64 - Socket 754/939/940
① Nipple Installation
Place a small washer on the motherboard. Then, put a nipple over it and fasten the nipple until the
Backplate for AMD64 is firmly attached to the motherboard on the opposite side of the CPU.
* A Retention Guide is not necessary for installing CNPS7700 LED on Socket 754/939/940.
Nipple
Small Washer
Motherboard
Backplate for AMD64
② Thermal Grease Application
Clear off particles and residue from the top of the
CPU then spread a thin layer of the included thermal
grease thoroughly on top of the CPU.
CPU (Lid)
Thermal Grease
③ Installation of Grips and Bolts
Interlock the L-Type grips with the clip. Insert the two bolts
into the outer holes of the grips.
Bolt
Grip (L-Type)
Outer Hole
④ FHS Placement
Set the FHS at the center of the CPU. Screw the bolts
in slightly, and then tighten each bolt a few turns at a
time while alternating between the two until the Grips
are completely pressed against the Nipples.
Grip (L-Type)
Nipple
⑤ Connect Power (Use FAN MATE 2)
◆ Please refer to FAN MATE 2 Installation and Usage on page 7.
※
The specifications of any product may change without prior notice to improve performance.
6
※FAN MATE 2 Installation and Usage
1) Installing FAN MATE 2 on the Inside of the System
Fan Connector
(CNPS7700 LED)
2) Installing FAN MATE 2 on the Outside of the System
Double-sided Tape
FAN MATE 2
Motherboard
Connect the appropriate 3-pin connector on the
cable to the motherboard fan header and the
CNPS7700 LED’s fan connector.
6-Pin Connector
Pull the 6-pin connector out of the system through
the back and connect it to FAN MATE 2, which
should be installed on the case using the included
double-sided tape.
◆ Fan speed can be controlled with the use of FAN MATE2. Turning the speed control knob in the clockwise
direction will increase the fan speed, and turning the speed control knob in the counter-clockwise direction will
decrease the fan speed.
Note) FAN MATE 2 has been specifically designed for the fan of this product. Zalman Tech Co., Ltd. is not
responsible for any damage to systems or CPUs caused by using it with other types of fans.
8. Notes on Usage
1) Checking CPU Compatibility
Please refer to “Compatible CPUs” on page 3 to confirm that your CPU is compatible before using the CPU cooler.
2) Cautions During Booting
When booting the computer, it may automatically power down after an alarm sound by a system
monitoring program to indicate that the CPU fan is rotating slowly. If this happens, turn the speed
control knob fully clockwise to increase the fan speed. Then set ‘CPU Fan Detected’ to ‘Disabled’ in
BIOS settings, or set the slowest rotational speed of the CPU fan in the system monitoring program to
less than or equal to 900rpm.
Note) Some motherboards do not boot if the rotational speed of the CPU fan is below a certain
rpm. If the BIOS settings are updated, Silent Mode can be used. For more information on
updating your BIOS, please refer to your motherboard manufacturer's website. Disabling
CPU fan speed detection in BIOS settings does not affect computer performance.
3) Overclocking
The fan should be set to Normal Mode if Overclocking.
(Zalman Tech Co., Ltd. is not responsible for any damage resulting from CPU Overclocking.)
※
The specifications of any product may change without prior notice to improve performance.
7
9. Zalman Computer Noise Prevention System
The use of Zalman's Noiseless Power Supplies, Fanless Northbridge Coolers, Heatpipe HDD
Coolers, Case Fans, VGA Coolers and Multi-Fan Controllers will allow you to maintain stable
performance and a noiseless environment.
Noiseless Power Supply
Noiseless Case Fan
Fanless Northbridge Cooler
Heatpipe HDD Cooler
Ultra Quiet VGA Cooler
Multi - Fan Controller
10. TNN (Totally No Noise) Computer Enclosures
TNN 300
TNN 500AF
TNN Computer Enclosures are the world’s first environment-friendly noiseless computer enclosures
that operate without the use of a fans. TNN Computer Enclosures use the aluminum enclosure itself
as a heatsink. They are ideal for environments that require silence, as well as for home theatre
systems and multi-media systems.
11. Home Theatre PC Enclosures
The HD160 is designed for ultra quiet home theatre
PC operation, utilizing optimized ventilation and
anti-vibration reinforcements, making it ideal for
environments that require silence such as living
rooms, bedrooms, educational facilities, and offices.
HD160
※
For more information, please visit our website.
The specifications of any product may change without prior notice to improve performance.
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement