Sharp 14A2-RU Operating instructions

Sharp 14A2-RU Operating instructions
SFC22-A/
SFC 14-A
Bedienungsanleitung
Operating instructions
Mode d’emploi
Istruzioni d’uso
Manual de instrucciones
Manual de instruções
Gebruiksaanwijzing
Οδηγιες χρησεως
Használati utasítás
Instrukcja obsługi
Инструкция по зксплуатации
Návod k obsluze
Návod na obsluhu
Upute za uporabu
Navodila za uporabo
Ръководство за обслужване
Instrucţiuni de utilizare
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
de
en
fr
it
es
pt
nl
el
hu
pl
ru
cs
sk
hr
sl
bg
ro
1
ꛈ
ꛉ
ꛋ ꛌ
SFC 14-A
ꛊ
ꛎ
ꛍ
ꛑ
ꛏ
ꛐ
ꛏ
ꛐ
ꛈ
SFC 22-A
ꛉ
ꛋ ꛌ
ꛊ
ꛎ
ꛍ
ꛑ
ꛐ
ꛏ
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
ꛐ
ꛏ
2
3
4
5
6
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
7
8
9
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
ORIGINAL OPERATING INSTRUCTIONS
SFC 22-A/SFC 14­A cordless
drill / driver
It is essential that the operating instructions are read before the
en power tool is operated for the first time.
Always keep these operating instructions together with the power
tool.
Ensure that the operating instructions are with the power tool when
it is given to other persons.
Contents
1
General information
3
Insert tools, accessories
2
4
5
6
7
8
9
10
11
12
. . . . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . . . . . .
16
17
. . . . . . . . . . . . . . . . .
18
Safety instructions . . . . . . . . . . . . . . . . . . . . .
20
Technical data . . . . . . . . . . . . . . . . . . . . . . . .
Before use . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
24
25
Care and maintenance . . . . . . . . . . . . . . . . . . .
26
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .
Manufacturer’s warranty - tools . . . . . . . . . . . . .
EC declaration of conformity (original) . . . . . . . .
27
29
29
1 These numbers refer to the corresponding illustrations. The
illustrations can be found on the fold-out cover pages. Keep these
pages open while studying the operating instructions.
In these operating instructions, the designation “power tool”
always refers to the SFC 22-A or SFC 14-A cordless combination
drill, with battery fitted.
Parts, operating controls and indicators 1
@
;
=
%
&
(
)
+
Keyless chuck
Torque and drilling mode setting ring
Control switch (with electronic speed control)
Forward / reverse switch
2-speed gear selector switch
Lamp
Grip
Release buttons with additional function (charge status
display activation)
§ Charge status and fault display (Li-ion battery)
/ Belt hook (optional)
1 General information
1.1 Safety notices and their meaning
DANGER
Draws attention to imminent danger that will lead to serious bodily
injury or fatality.
WARNING
Draws attention to a potentially dangerous situation that could
lead to serious personal injury or fatality.
CAUTION
Draws attention to a potentially dangerous situation that could
lead to slight personal injury or damage to the equipment or other
property.
NOTE
Draws attention to an instruction or other useful information.
16
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
1.2 Explanation of the pictograms and other information
Warning signs
General warning
en
Warning:
electricity
Warning: caustic
substances
Wear a hard hat
Wear ear
protection
Wear protective
gloves
Read the
operating
instructions
before use
Volts
Direct current
Rated speed
under no load
Revolutions per
minute
Drilling without
hammering
Return waste
material for
recycling.
Obligation signs
Wear eye
protection
Wear breathing
protection
Symbols
Location of identification data on the power tool
The type designation can be found on the type identification
plate at the base of the power tool and the serial number on the
side of the casing. Make a note of this data in your operating
instructions and always refer to it when making an enquiry to your
Hilti representative or service department.
Type:
Generation: 01
Serial no.:
2 Description
2.1 Use of the product as directed
The SFC 22­A or SFC 14­A is a hand-held, battery powered
combination drill for screwing and unscrewing screws and for
drilling in steel, wood and plastic.
Working on materials hazardous to the health (e.g. asbestos) is
not permissible.
Do not use the battery as a power source for other unspecified
appliances.
Modification of the power tool or tampering with its parts is not
permissible.
To avoid the risk of injury, use only genuine Hilti accessories and
insert tools.
Observe the information printed in the operating instructions
concerning operation, care and maintenance.
The power tool is designed for professional use and may be
operated, serviced and maintained only by trained, authorized
personnel. This personnel must be informed of any special
hazards that may be encountered. The power tool and its
ancillary equipment may present hazards when used incorrectly
by untrained personnel or when used not as directed.
17
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
The working environment may be as follows: construction site,
workshop, renovation, conversion or new construction.
2.2 Chuck
Keyless chuck
en 2.3 Switches
Control switch with electronic speed control
2-speed gear selector switch
Forward / reverse selector switch with safety lock
Torque and drilling mode setting ring
2.4 Grips
Vibration-absorbing grip
2.5 Lubrication
Grease lubrication
2.6 The items supplied include (toolbox versions):
1 Power tool
1 Operating instructions
1 Hilti toolbox
2.7 The items supplied include (cardboard box versions):
1 Power tool
1 Operating instructions
2.8 Additional items required for operating the tool
B 22/1.6 Li­Ion, B 22/2.6 Li­Ion, B 22⁄3.3 Li­Ion, B 14/1.6 Li­Ion
or B 14/3.3 Li­Ion battery with C4⁄36­90, C4⁄36­350, C 4/36,
C 4/36­ACS or C 4/36­ACS TPS charger.
2.9 Li-ion battery charge status and overheating indicator
LEDs light constantly
LEDs blink
Charge status C
LED 1, 2, 3, 4
-
C ≧ 75 %
LED 1, 2, 3
-
50 % ≦ C < 75 %
LED 1, 2
-
25 % ≦ C < 50 %
LED 1
-
10 % ≦ C < 25 %
-
LED 1
C < 10 %
-
LED 1
Battery overheated
2.10 Overload and overheating protection
The power tool is equipped with an electronic protection system
to prevent overloading and overheating. The power tool switches
itself off automatically in the event of overloading and overheating.
After releasing the control switch, the power tool may not restart
immediately when the switch is pressed again (while the power
tool is cooling down).
3 Insert tools, accessories
Designation
Short designation
Charger for Li-ion batteries
C 4/36
Charger for Li-ion batteries
C 4/36­ACS
Charger for Li-ion batteries
C 4/36-ACS TPS
Charger for Li-ion batteries
C 4/36­90
Charger for Li-ion batteries
C 4/36­350
Battery
B 22/1.6 Li­Ion
Battery
B 22/2.6 Li­Ion
Battery
B 22/3.3 Li­Ion
Battery
B 14/1.6 Li­Ion
Bit holder
S-BH 50
18
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
Designation
Short designation
Battery
B 14/3.3 Li­Ion
Belt hook (optional)
Designation
Description
en
Keyless chuck clamping range ∅ 1.5…13 mm
Drilling diameter range in wood ∅ 1.5…20 mm
(soft)
Drilling diameter range in wood ∅ 1.5…12 mm
(hard)
Drilling diameter range in metal ∅ 1.5…10 mm
Wood screws (max. length 80
mm)
Driving screws in plastic anchors (max. length 120 mm)
∅ 3…6 mm
∅ Max. 8 mm
4 Technical data
Right of technical changes reserved.
Power tool
SFC 14­A
SFC 22­A
Rated voltage (DC
voltage)
14.4 V
21.6 V
Weight in accordance with EPTA
procedure 01/2003
1.5 kg
1.7 kg
Dimensions (L x
W x H with B
14/1.6 or B 22/1.6)
192 mm x 80 mm x
225 mm
202 mm x 92 mm x
234 mm
1st gear speed
(with B 14/3.3 or
B 22/2.6)
0…500/min
0…600/min
2nd gear speed
(with B 14/3.3 or B
22/2.6)
0…1,700/min
0…1,800/min
Torque with tool
set to drilling symbol (soft/flexible
joint)
Max. 24 Nm
Max. 28 Nm
Torque range (15
settings)
1.5…10 Nm
1.5…10 Nm
NOTE
The vibration emission level given in this information sheet has
been measured in accordance with a standardized test given in EN
60745 and may be used to compare one tool with another. It may
be used for a preliminary assessment of exposure. The declared
vibration emission level represents the main applications of the
tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission
may differ. This may significantly increase the exposure level over
the total working period. An estimation of the level of exposure
to vibration should also take into account the times when the tool
is switched off or when it is running but not actually doing the
job. This may significantly reduce the exposure level over the total
working period. Identify additional safety measures to protect the
operator from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organization of work
patterns.
Noise and vibration information (measured in accordance
with EN 60745):
Typical A-weighted sound
power level for the SFC 22-A
80 dB (A)
Typical A-weighted emission
sound pressure level for the
SFC 22-A.
69 dB (A)
Typical A-weighted sound
power level for the SFC 14-A
80 dB (A)
19
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
Typical A-weighted emission
sound pressure level for the
SFC 14-A.
69 dB (A)
Uncertainty for the given sound 3 dB (A)
level
en Triaxial vibration values (vibration vector sum)
measured in accordance with
EN 60745­2­2
For the SFC 22­A: Screwdriving 1 m/s²
without impact action, ah
For the SFC 14­A: Screwdriving 1 m/s²
without impact action, ah
Uncertainty (K)
1.5 m/s²
Triaxial vibration values (vibration vector sum)
measured in accordance with
EN 60745­2­1
For the SFC 14­A: Drilling in
metal, ah,D
2.0 m/s²
For the SFC 22­A: Drilling in
metal, ah,D
2.0 m/s²
Uncertainty (K) for triaxial vibra- 1.5 m/s²
tion measurements
Battery
B 14/1.6 Li­Ion
B 14/3.3 Li­Ion
Rated voltage
14.4 V
14.4 V
Capacity
1.6 Ah
3.3 Ah
Energy content
23.04 Wh
47.52 Wh
Weight
0.36 kg
0.60 kg
Temperature monitoring
Yes
Yes
Type of cell
Li-ion
Li-ion
No. of cells
4
8
B 22/1.6
Li­Ion
B 22/2.6
Li­Ion
B 22/3.3
Li­Ion
Capacity
1.6 Ah
2.6 Ah
3.3 Ah
Energy content
34.56 Wh
56.16 Wh
71.28 Wh
Weight
0.48 kg
0.78 kg
0.78 kg
Temperature
monitoring
Yes
Yes
Yes
Type of cell
Li-ion
Li-ion
Li-ion
No. of cells
6
12
12
Battery
Rated voltage
21.6 V
21.6 V
21.6 V
5 Safety instructions
NOTE
The safety rules in section 5.1 contain all general safety rules for
power tools which, in accordance with the applicable standards,
must be listed in the operating instructions. Accordingly, some of
the rules listed may not be relevant to this tool.
5.1 General power tool safety warnings
a)
WARNING
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury. Save all warnings and
instructions for future reference. The term “power tool” in
the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.
5.1.1 Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or
fumes.
20
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
5.1.2 Electrical safety
a) Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching en
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use
of an RCD reduces the risk of electric shock.
5.1.3 Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating
power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off‐position before connecting to power source and/or
battery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and
properly used. Use of dust collection can reduce dust-related
hazards.
5.1.4 Power tool use and care
a) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the
battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
21
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed. Use
of the power tool for operations different from those intended
en
could result in a hazardous situation.
f)
5.1.5 Battery tool use and care
a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack
may create a risk of fire when used with another battery pack.
b) Use power tools only with specifically designated battery
packs. Use of any other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.
5.1.6 Service
a) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.
5.2 Drill safety warnings
a) Wear ear protectors when impact drilling. Exposure to noise
can cause hearing loss.
b) Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
c) Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
5.3 Additional safety precautions
5.3.1 Personal safety
a) Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give
the operator an electric shock.
b) Always hold the power tool securely with both hands on
the grips provided. Keep the grips dry, clean and free from
oil and grease.
c) Improve the blood circulation in your fingers by relaxing
your hands and exercising your fingers during breaks
between working.
d) Avoid touching rotating parts. Switch the power tool
on only after bringing it into position at the workpiece.
Touching rotating parts, especially rotating insert tools, may
lead to injury.
e) Activate the safety lock (forward / reverse switch in the
middle position) before storing or transporting the power
tool.
f) The power tool is not intended for use by children, by debilitated persons or those who have received no instruction
or training.
g) Children must be instructed not to play with the power tool.
h) Dust from material such as paint containing lead, some wood
species, minerals and metal may be harmful. Contact with
or inhalation of the dust may cause allergic reactions and/or
respiratory diseases to the operator or bystanders. Certain
kinds of dust are classified as carcinogenic such as oak and
beech dust especially in conjunction with additives for wood
conditioning (chromate, wood preservative). Material containing asbestos must only be treated by specialists. Where the
use of a dust extraction device is possible it shall be used.
22
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
To achieve a high level of dust collection, use a suitable
vacuum cleaner of the type recommended by Hilti for wood
dust and/or mineral dust together with this tool. Ensure
that the workplace is well ventilated. The use of a dust
mask of filter class P2 is recommended. Follow national
requirements for the materials you want to work with.
5.3.2 Power tool use and care
a) Secure the workpiece. Use clamps or a vice to secure the
workpiece. The workpiece is thus held more securely than by
hand and both hands remain free to operate the power tool.
b) Check that the insert tools used are compatible with the
chuck system and that they are secured in the chuck
correctly.
c) Large and heavy insert tools must only be operated in first
gear. There is otherwise a risk that the tool will be damaged
when it is switched off or, under unfavorable conditions, the
chuck might be detached.
5.3.3 Cordless tool use and care
a) Ensure the switch is in the off position before inserting
battery pack. Inserting the battery pack into power tools that
have the switch on invites accidents.
b) Do not expose batteries to high temperatures or fire. This
presents a risk of explosion.
c) Do not disassemble, squash or incinerate batteries and do
not subject them to temperatures over 80°C. A risk of fire,
explosion or injury through contact with caustic substances
may otherwise result.
d) Avoid ingress of dampness.Dampness may cause a short
circuit resulting in a risk of burning injury or fire.
e) Do not use batteries other than those approved for use
with the applicable power tool or appliance. Use of other
batteries or use of the battery for purposes for which it is not
intended presents a risk of fire and explosion.
f) Observe the special instructions applicable to the transport, storage and use of Li-ion batteries.
g) Remove the battery before storing or transporting the
power tool.
h) Avoid short-circuiting the battery. Check that the terminals
on the battery and in the power tool are free from foreign
objects before inserting the battery in the power tool. Short
circuiting the battery terminals presents a risk of fire, explosion
and chemical burns.
i) Do not charge or continue to use damaged batteries (e.g.
batteries with cracks, broken parts, bent or pushed-in
and/or pulled-out contacts).
j) If the battery gets too hot to touch, this may indicate that it
is faulty. Place the tool in a location where it can be kept
under observation, well away from flammable materials,
and allow it to cool down. Contact Hilti Service after the
battery has been allowed to cool.
5.3.4 Electrical safety
Before beginning work, check the working area (e.g. using a
metal detector) to ensure that no concealed electric cables or
gas and water pipes are present. External metal parts of the
power tool may become live, for example, when an electric cable
is damaged accidentally. This presents a serious risk of electric
shock.
5.3.5 Work area safety
a) Ensure that the workplace is well lit.
b) Ensure that the workplace is well ventilated. Exposure to
dust at a poorly ventilated workplace may result in damage to
the health.
23
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
en
5.3.6 Personal protective equipment
en
The user and any other persons in the vicinity must wear
suitable eye protection, a hard hat, ear protection, protective
gloves and breathing protection while the tool is in use.
6 Before use
6.1 Battery use and care
NOTE
Battery performance drops at low temperatures. Use a battery
only when it has been fully charged. This ensures that maximum
battery capacity is available. Change to the second battery as
soon as a drop in performance is noticed. Recharge the battery
immediately so that it is ready for reuse.
Store the battery in a cool, dry place. Never store the battery
where it is exposed to direct sunlight or sources of heat, e.g. on
heaters / radiators or behind a motor vehicle windscreen. Batteries
that have reached the end of their life must be disposed of safely
and correctly to avoid environmental pollution.
6.2 Charging the battery
DANGER
Use only the Hilti batteries and Hilti chargers listed under
“Accessories”.
6.2.1 Charging a new battery for the first time
Charge the battery fully before using it for the first time.
6.2.2 Charging a previously used battery
Ensure that the outer surfaces of the battery are clean and dry
before inserting it in the corresponding charger.
Read the operating instructions for the charger for further information about the charging procedure.
Li-ion batteries are ready for use at any time, even when only partly
charged. Charging progress is indicated by the LED display (see
charger operating instructions).
6.3 Fitting the battery
CAUTION
Before fitting the battery, check that the power tool is switched
off and that the safety lock is engaged (forward/reverse switch
in the middle position). Use only the Hilti batteries approved
for use with this power tool.
CAUTION
Check that the terminals on the battery and in the power tool
are free from foreign objects before inserting the battery in
the power tool.
1. Push the battery into the power tool from the rear as far as it
will go and until it is heard to engage with a double click.
2. CAUTION A falling battery may present a risk of injury to
yourself or others.
Check that the battery is seated securely in the power tool.
24
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
6.4 Removing the battery 2
1. Press one or both release buttons.
2. Pull the battery out of the power tool toward the rear.
6.5 Transport and storage of battery packs
Pull the battery pack out of the locked position (working position) en
and move it into the first click-stop position (transport position).
If you disconnect a battery pack from the power tool for transport
or storage, make sure that the contacts of the battery pack are
not short-circuited. Remove loose metal parts such as screws,
nails, clamps, loose screw bits, wires or metal swarf from the case,
toolbox or transport container, or prevent these parts from coming
into contact with the battery packs.
Observe national and international transport regulations when
shipping battery packs (transportation by road, rail, sea or air).
6.6 Belt hook 3
CAUTION
Check that the belt hook is fitted securely before beginning
work.
The belt hook allows the power tool to be attached to a belt worn
by the operator. The belt hook can also be fitted to the other side
of the power tool for use by left-handed persons.
1. Pull the battery out of the tool.
2. Fit the mounting plate into the guides provided.
3. Secure the belt hook with the two screws.
7 Operation
CAUTION
The tool may get hot during use. Wear protective gloves.
CAUTION
When drilling and screwdriving, the grip of the tool may be
deflected laterally (the tool tends to pivot about its own axis).
CAUTION
To avoid injuries caused by the insert tool, wear protective
gloves when changing insert tools.
7.1 Setting forward or reverse rotation 4
NOTE
The forward / reverse switch is used to select the direction of
rotation of the drive spindle. An interlock prevents switching
while the motor is running. The control switch is locked when the
forward / reverse switch is in the middle position. Push the forward
/ reverse switch to the right (power tool held in working direction)
to select forward rotation. Push the forward / reverse switch to the
left (power tool held in working direction) to select reverse rotation.
7.2 Speed selection using the 2-speed gear switch 5
WARNING
Large and heavy insert tools must only be operated in first
gear. There is otherwise a risk that the tool will be damaged when
it is switched off or, under unfavorable conditions, the chuck might
be detached.
NOTE
The mechanical 2-speed gear switch can be used to select the
speed range required. Speed with fully-charged battery: SFC
14­A: 1st gear: 0­500 /min., 2nd gear: 0­1700 /min. SFC 22­A: 1st
gear: 0­600 /min., 2nd gear: 0­1800 /min.
7.3 Switching on / off
Speed of rotation can be controlled smoothly up to maximum
speed by pressing the control switch slowly.
7.4 Fitting the drill bit
1. Set the forward / reverse switch to the middle position or
remove the battery from the power tool.
25
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
2. Check that the connection end of the drill bit is clean. Clean
the connection end if necessary.
3. Insert the drill bit in the keyless chuck and then turn the chuck
firmly by hand until several clicks are heard.
4. Check that the drill bit is held securely.
en 7.5 Removing the drill bit
1. Set the forward / reverse switch to the middle position or
remove the battery from the power tool.
2. Open the keyless chuck.
3. Pull the insert tool out of the chuck.
7.6 Drilling
CAUTION
Use clamps or a vice to secure the workpiece. The workpiece
is thus held more securely than by hand and both hands remain
free to operate the power tool.
1. Turn the torque and operating mode setting ring to the drilling
symbol.
2. Move the forward / reverse switch to the “Forward” position.
7.7 Screwdriving
7.7.1 Fitting the bit holder / bit
1. Set the forward / reverse switch to the middle position or
remove the battery from the power tool.
2. Open the quick-release chuck.
3. Insert the bit adapter in the keyless chuck and then turn the
chuck firmly by hand until tight.
4. Check that the bit adapter is held securely (check by pulling).
5. Fit the bit in the bit holder.
7.7.2 Screwdriving
1. Select the torque function on the setting ring for torque and
drilling.
2. Set the forward / reverse switch to the desired direction of
rotation.
7.7.3 Removing the bit / bit holder
1. Set the forward / reverse switch to the middle position or
remove the battery from the power tool.
2. Remove the bit from the bit holder.
3. Open the keyless chuck.
4. Remove the bit adapter.
7.8 Reading the charge status LED display on Li­ion batteries 6
NOTE
The charge status can not be indicated while the power tool is
in operation. LED 1 blinks when the battery is fully discharged
or when it is too hot (temperature above 80°C). The battery must
then be inserted in the charger.
The Li-ion battery features a charge status LED display. The
charge status is indicated by the LEDs on the battery during
charging (please refer to the operating instructions for the charger).
When the battery is not in use, pressing one of the battery release
buttons or inserting the battery into the power tool causes the
battery charge status to be displayed by the four LEDs for three
seconds.
8 Care and maintenance
CAUTION
Before beginning cleaning, remove the battery from the power
tool in order to prevent unintentional starting.
8.1 Care of insert tools
Clean off dirt and dust deposits adhering to the insert tools and
protect them from corrosion by wiping the insert tools from time
to time with an oil-soaked rag.
26
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
8.2 Care of the power tool
CAUTION
Keep the power tool, especially its grip surfaces, clean and
free from oil and grease. Do not use cleaning agents which
contain silicone.
The outer casing of the power tool is made from impact-resistant en
plastic. Sections of the grip are made from a synthetic rubber
material.
Never operate the power tool when the ventilation slots are
blocked. Clean the ventilation slots carefully using a dry brush.
Do not permit foreign objects to enter the interior of the power
tool. Clean the outside of the power tool at regular intervals with a
slightly damp cloth. Do not use a spray, steam pressure cleaning
equipment or running water for cleaning. This may negatively
affect the electrical safety of the power tool.
8.3 Care of the Li-ion battery
Avoid entrance of moisture.
Charge the battery fully before using it for the first time.
In order to achieve maximum battery life, stop discharging the
battery as soon as a significant drop in performance is noticed.
NOTE
If use of the power tool continues, battery discharge is stopped
automatically (indicated by LED 1 blinking) before the battery cells
suffer damage.
Charge the battery with the Hilti charger approved for use with
Li-ion batteries.
NOTE
– A conditioning charge (as is required with NiCd or NiMH
batteries) is not necessary.
– Interruption of the charging procedure has no negative effect
on battery life.
– Charging can be started at any time with no negative effect
on battery life. There is no memory effect (as with NiCd or
NiMH batteries).
– For best results, batteries should be stored fully charged in a
cool dry place. Avoid charging the battery in places subject
to high ambient temperatures (e.g. at a window) as this has
an adverse effect on battery life and increases the rate of
self-discharge.
– If the battery no longer reaches full charge, it may have lost
capacity due to aging or overstressing. It is possible to
continue working with a battery in this condition but it should
be replaced in good time.
8.4 Maintenance
WARNING
Repairs to the electrical section of the power tool may be
carried out only by trained electrical specialists.
Check all external parts of the power tool for damage at regular
intervals and check that all controls operate faultlessly. Do not
operate the power tool if parts are damaged or when the controls
do not function faultlessly. If necessary, the power tool should be
repaired by Hilti Service.
8.5 Checking the power tool after care and maintenance
After carrying out care and maintenance work on the power tool,
check that all protective and safety devices are fitted and that they
function faultlessly.
9 Troubleshooting
Fault
Possible cause
Remedy
The power tool
doesn’t run.
The battery is discharged or fitted incorrectly.
The battery must be
heard to engage with
a double click or,
respectively, needs
to be charged.
Electrical fault.
Remove the battery
from the power tool
and contact Hilti Service.
27
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
Fault
Possible cause
Remedy
The power tool
The battery is disdoesn’t run and 1 charged.
LED blinks.
Change the battery
and recharge the
discharged battery.
The on / off switch
can’t be pressed,
i.e. the switch is
locked.
Push the forward /
reverse switch to the
left or right.
en
The battery is too hot Bring the battery to
or too cold.
the recommended
working temperature.
The forward / reverse switch is in
the middle position
(transport lock engaged).
The battery runs Battery condition is
down more
not optimal.
quickly than usual.
The battery does- The retaining lugs on
n’t engage with
the battery are dirty.
an audible double
click.
LED 1 blinks.
The battery is discharged.
The tool is
overloaded
(application limits
exceeded).
Have battery condition diagnosed by
Hilti Service or replace with a new battery.
Clean the retaining
lugs and check that
the battery engages
securely. Contact Hilti
Service if the problem
persists.
Charge the battery.
Use the right power
tool for the job (don’t
use a low-powered
tool for heavy work).
10 Disposal
CAUTION
Improper disposal of the equipment may have serious consequences: the burning of plastic components generates toxic
fumes which may present a health hazard. Batteries may explode if damaged or exposed to very high temperatures, causing
poisoning, burns, acid burns or environmental pollution. Careless
disposal may permit unauthorized and improper use of the equipment. This may result in serious personal injury, injury to third
parties and pollution of the environment.
CAUTION
Dispose of defective batteries without delay. Keep them out of
reach of children. Do not attempt to open or dismantle batteries
and do not dispose of them by incineration.
CAUTION
Dispose of the batteries in accordance with national regulations or
return them to Hilti.
Most of the materials from which Hilti power tools or appliances
are manufactured can be recycled. The materials must be correctly
separated before they can be recycled. In many countries, Hilti
has already made arrangements for taking back your old power
tools or appliances for recycling. Please ask your Hilti customer
service department or Hilti representative for further information.
28
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
For EC countries only
Disposal of electric tools together with household
waste is not permissible.
In observance of the European Directive on waste
electrical and electronic equipment and its implementation in accordance with national law, electrical
appliances that have reached the end of their life must en
be collected separately and returned to an environmentally compatible recycling facility.
11 Manufacturer’s warranty - tools
Hilti warrants that the tool supplied is free of defects in material
and workmanship. This warranty is valid so long as the tool is
operated and handled correctly, cleaned and serviced properly
and in accordance with the Hilti Operating Instructions, and the
technical system is maintained. This means that only original Hilti
consumables, components and spare parts may be used in the
tool.
This warranty provides the free-of-charge repair or replacement
of defective parts only over the entire lifespan of the tool. Parts
requiring repair or replacement as a result of normal wear and tear
are not covered by this warranty.
Additional claims are excluded, unless stringent national rules
prohibit such exclusion. In particular, Hilti is not obligated for
direct, indirect, incidental or consequential damages, losses
or expenses in connection with, or by reason of, the use of,
or inability to use the tool for any purpose. Implied warranties
of merchantability or fitness for a particular purpose are
specifically excluded.
For repair or replacement, send the tool or related parts immediately upon discovery of the defect to the address of the local Hilti
marketing organization provided.
This constitutes Hilti’s entire obligation with regard to warranty
and supersedes all prior or contemporaneous comments and oral
or written agreements concerning warranties.
12 EC declaration of conformity (original)
Designation:
Cordless drill / driver
Type:
SFC 22-A/SFC 14­A
Generation:
01
Year of design:
2010
We declare, on our sole responsibility, that this product complies
with the following directives and standards: 2006/42/EC,
2004/108/EC,
2006/66/EC,
2011/65/EU,
EN
60745­1,
EN 60745­2­1, EN 60745­2­2, EN ISO 12100.
Hilti Corporation, Feldkircherstrasse 100, FL­9494 Schaan
Paolo Luccini
Head of BA Quality and Process Management
Business Area Electric Tools & Accessories
01/2012
Jan Doongaji
Executive Vice President
Business Unit Power Tools & Accessories
01/2012
Technical documentation filed at:
Hilti Entwicklungsgesellschaft mbH
Zulassung Elektrowerkzeuge
Hiltistrasse 6
86916 Kaufering
Deutschland
29
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
Hilti Corporation
Printed: 05.09.2013 | Doc-Nr: PUB / 5071565 / 000 / 01
440881 / A3
440881
Hilti = registered trademark of Hilti Corp., Schaan
W 3911 I 0713 I 00-Pos. 1 I 1
Printed in China © 2013
Right of technical and programme changes reserved S. E. & O.
*440881*
LI-9494 Schaan
Tel.: +423 / 234 21 11
Fax: +423 / 234 29 65
www.hilti.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement