Blue Rhino | Endless Summer 62301 | Owner`s manual | Blue Rhino Endless Summer 62301 Owner`s manual

®
OWNER’S MANUAL
Outdoor Patio Heater
Model No. 200209
DANGER
CARBON MONOXIDE HAZARD
• This appliance can produce
carbon monoxide which has no
odor.
• Using it in an enclosed space
can kill you.
• Never use this appliance in
an enclosed space such as a
camper, tent, car or home.
WARNING
FOR YOUR SAFETY:
For Outdoor Use Only
(outside any enclosure)
WARNING
FOR YOUR SAFETY:
Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage.
Read the installation, operation, and
maintenance instructions thoroughly
before installing or servicing this
equipment.
Failure to follow these instructions could
result in fire or explosion, which could
cause property damage, personal injury, or
death.
Made from 70% Bagasse
(Environmentally Friendly Sugar
Cane Pulp By-product)
Table of Contents
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
Exploded View & Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installling LP Gas Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Insert LP Gas Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Secure LP Gas Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connect LP Gas Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Disconnect LP Gas Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Checking for Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Before Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
When heater is ON. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Re-Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Cleaning Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
The use and installation of this product must conform to local codes. In absence of local codes,
use the National Fuel Gas Code, ANSI Z223.1/NFPA 54, CAN/CGA-B149.1, Natural Gas and
Propane Installation Code.
California Proposition 65: Chemicals known to the State of California to cause cancer, birth
defects, or other reproductive harm are created by the combustion of propane.
Save these instructions for future reference. If you are assembling this unit for someone else,
give this manual to him or her to read and save for future reference.
Manufactured in China for:
Blue Rhino Global Sourcing, Inc.
Winston-Salem, NC 27105 USA
1.800.762.1142, www.bluerhino.com
© 2007 Blue Rhino Global Sourcing, Inc. All Rights Reserved
Endless Summer® is a Registered Trademark of Blue Rhino Global Sourcing, Inc. All Rights Reserved
200209-OM-215 E
®
Outdoor Patio Heater Model No. 200209
DANGERS and WARNINGS: FOR YOUR SAFETY
DANGER
If you smell gas 1. Shut off gas to appliance.
2. Extinguish any open flame.
3. If odor continues, immediately call your gas supplier or your fire
department.
WARNING
FOR YOUR SAFETY
1. Do not store spare LP cylinder within 10 feet (3.05 m) of this appliance.
2. Do not store or use gasoline or other flammable vapors and liquids
within 25 feet (7.62 m) of this or any other appliance.
3. An LP cylinder not connected for use shall not be stored in the vicinity
of this or any other appliance.
DANGER: Failure to follow the dangers, warning and cautions in this manual may result in serious bodily injury or death, or in a fire or an explosion
causing damage to property.
WARNING:
This heater is for outdoor use only, and shall not be used in a building,
garage, or any other enclosed area.
Always maintain at least 36” clearance (top), and 24” clearance (side)
from combustible materials.
This heater is for use with liquid propane (LP) gas only. The conversion
to or attempted use of natural gas in this LP gas heater is dangerous
and will void your warranty.
LP gas Characteristics:
a. LP gas is flammable and hazardous if handled improperly. Become
aware of the characteristics before using any LP gas product.
b. LP gas is explosive under pressure, heavier than air, and settles and
pools in low areas.
c. LP gas in its natural state has no odor. For your safety, an odorant is
added that smells like rotten cabbage.
d. Contact with LP gas can cause freeze burns to skin.
LP gas tank needed to operate. Only tanks marked “propane” may be
used.
The LP gas supply tank must be constructed and marked in accordance
with the Specifications for LP gas Cylinders of the U.S. Department of
Transportation (DOT) or the National Standard of Canada, CAN/CSAB339, Cylinders, Spheres and Tubes for the Transportation of Dangerous
Goods; and Commission.
LP gas tank must be arranged for vapor withdrawal.
The LP gas tank must have a listed overfilling prevention device (OPD).
Only use 20-pound cylinders equipped with a cylinder connection device
compatible with the connection for outdoor cooking appliances.
The LP gas tank must have a tank collar to protect the tank valve.
Never use an LP gas tank with a damaged body, valve, collar, or footing.
Dented or rusted LP gas tanks may be hazardous and should be
checked by your LP gas supplier prior to use.
The LP gas tank should not be dropped or handled roughly.
Tanks must be stored outdoors out of the reach of children and must
not be stored in a building, garage, or any other enclosed area. Your
tank must never be stored where temperatures can reach over 125°F.
Never keep a filled LP gas tank in a hot car or car trunk. Heat will cause
the gas pressure to increase, which may open the relief valve and allow
gas to escape.
Do not store a spare LP gas tank under or near this appliance.
Never fill the tank beyond 80 percent full.
Never attempt to attach this heater to the self-contained LP gas system
of a camper trailer, motor home, or house.
The use of alcohol, or prescription or non-prescription drugs may
impair the consumer’s ability to properly assemble or safely operate the
appliance.
Your heater has been checked at all factory connections for leaks.
Recheck all connections, as movement in shipping can loosen
connections.
Check for leaks even if your unit was assembled for you by someone
else.
Do not operate if gas leak is present. Gas leaks may cause a fire or
explosion.
You must follow all leak-checking procedures before operating. To
prevent fire or explosion hazard when testing for a leak:
a. Always perform leak test before lighting the heater and each time the
tank is connected for use.
b. No smoking. Do not use or permit sources of ignition in the area
while conducting a leak test.
c. Conduct the leak test outdoors in a well-ventilated area.
d. Do not use matches, lighters, or a flame to check for leaks.
e. Do not use heater until any and all leaks are corrected.
If you are unable to stop a leak, disconnect the LP gas supply. Call a
gas appliance serviceman or your local LP gas supplier.
Do not store or use gasoline or other flammable liquids or vapors within
25 feet (7.62 m) of this appliance.
Do not use in an explosive atmosphere. Keep heater area clear and free
from combustible materials, gasoline and other flammable vapors and
liquids.
Keep all combustible items and surfaces away from the heater at all
times. DO NOT use this heater or any gas product under any overhead or
near any unprotected combustible constructions.
Combustion of propane creates carbon monoxide, which, when used in
enclosed areas, can kill you.
It is essential to keep the heater’s valve compartment, burners, and
circulating air passages clean. Inspect heater before each use.
Installation and repair should be done by a qualified service person.
Do not alter heater in any manner.
Do not use the heater unless it is COMPLETELY assembled and all parts
are securely fastened and tightened.
This heater should be thoroughly inspected before each use. Clean and
inspect the hose before each use of the appliance. If there is evidence
of abrasion, wear, cuts, or leaks, the hose must be replaced prior to the
appliance being put into operation.
Use only the regulator and hose assembly provided. The replacement
regulator and hose assembly shall be that specified by the
manufacturer.
Inspect heater before each use. If a damaged part is detected, do not
operate until an original equipment replacement part has been properly
installed.
Use only Blue Rhino Global Sourcing, Inc. factory authorized parts. The
use of any part that is not factory authorized can be dangerous. This
will also void your warranty.
Dome and burner are extremely hot to the touch during operation. Never
touch the dome or burner while the heater is operating. Wait for unit to
cool down (approximately 45 minutes) after use.
During operation, do not touch burner assembly. The surface of heater’s
emitter can reach temperatures approaching 1600ºF.
Do not install or use in or on boats or recreational vehicles.
Do not use heater in winds that exceed 10 m.p.h..
Unit will operate at reduced efficiency below 40ºF (5ºC).
Do not leave a lit heater unattended, especially keep children and pets
away from heater at all times.
Always use extreme caution when near heater. Alert both children and
adults to the hazards of high temperatures, especially to avoid burns or
clothing catching fire.
Do not attempt to move heater when in use. Allow the heater to cool
before moving or storing.
Storage of heater indoors is permissible only if the tank is disconnected,
removed from the heater and properly stored outdoors.
Do not attempt to disconnect the gas regulator from the tank or any gas
fitting while the heater is in use.
Always place your heater on a hard, level surface.
Use extreme caution on wooden decks.
Move gas hoses as far away as possible from hot surfaces.
Keep all electrical cords away from a hot heater.
Do not use heater for indoor cooking or heating. TOXIC fumes can
accumulate and cause asphyxiation.
Keep sprinklers and other water sources away from burner and
controls.
Do not hang clothing or other flammable materials either on or near
heater.
Always allow heater to cool before attempting service.
Any guard or other protective device removed for servicing the heater
must be replaced prior to operating the heater.
Certain materials or items, when stored under heater, will be subjected
to radiant heat and could be seriously damaged.
After a period of storage and/or nonuse, check for leaks, burner
obstructions and inspect for any abrasion, wear, cuts to the hose.
If at any time you are unable to light burner and smell gas, wait 5
minutes to allow gas to dissipate before attempting to light heater.
Failure to not wait 5 minutes to allow the gas to clear if the heater does
not light, may result in an explosive flame-up.
Be careful when attempting to manually ignite this heater. Holding in
the control knob for more than 10 seconds before igniting the gas will
cause a ball of flame upon ignition.
Avoid inhaling fumes emitted from the heater’s first use. Smoke and
odor from the burning of oils used in manufacturing will appear. Both
smoke and odor will dissipate after approximately 30 minutes. The
heater should NOT produce thick black smoke.
If heater is not in use, the gas must be turned off at the supply tank.
Do not use this appliance without reading “Operating Instructions” in
this manual.
Deaths, serious injury or damage to property may occur if the above is
not followed exactly.
page no.
3
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
Parts List
Exploded View
1
Finial
56-01-103
2
Dome Cap
56-01-104
3
Dome Plate
56-01-105
4
Dome Panel (3)
56-01-106
5
Dome Rib (3)
56-01-109
6
Dome Pin* (3)
56-01-459
7
Bottom Plate
56-01-110
8
Emitter Top*
56-01-399
9
Emitter Screen*
56-01-118
10
Burner*
56-01-334
11
Pilot Heat Shield*
56-01-151
12
Pilot Assembly*
56-01-127
13
Burner Orifice*
56-01-131
14
Electronic Igniter*
56-01-142
15
Igniter Button*
56-01-188
16
Control Knob*
56-01-156
17
Access Panel*
56-01-140
18
Valve*
56-01-144
19
Valve Bracket*
56-01-463
20
Tip Switch*
56-01-019
21
Valve Housing*
56-01-144
22
Gas Line
56-01-190
23
Pole
56-01-158
24
Shroud
56-01-164
25
Platform
56-01-165
26
Gas Line Clip
56-01-213
27
Leg (3)
56-01-193
28
Tank Retention Chain
56-01-186
29
Regulator/Hose Assembly
56-01-192
30
Base
56-01-196
31
Weight Plate
56-01-470
32
Wheel Hole Plug (2)*
56-01-402
1
2
3
5
4
6
7
8
9
10
11
12
13
21
14
15
22
20
23
19
18
17
16
24
25
26
27
29
28
32
30
* Pre Assembled
31
Hardware
A
B
C
D
E
F
G
H
I
J
K
L
Screw
5/32” - 32 x 8 Stainless Steel Round Head
3 pcs
Screw
3/16” - 24 x 15 Black Zinc Plated Philips Head
1 pc
Screw
1/4” - 20 x 16 Stainless Steel Philips Head
4 pcs
Bolt
1/4” - 20 x 20 Nickel Plated Hex Head
12 pcs
Bolt
3/8” - 16 x 35 Stainless Steel Hex Head
1 pc
Bolt
3/8” - 16 x 95 Nickel Plated Hex Head
1 pc
Nut
1/4” - 20 Nickel Plated Hex
15 pcs
Nut
3/8” - 16 Stainless Steel Hex
1 pc
Nut
3/8” - 16 Nickel Plated Hex
1 pc
Lock Washer
ø6 Nickel Plated
12 pcs
Lock Washer
ø10 Nickel Plated
1 pc
AA Battery
AA Battery
1 pc
Tools Required for Assembly (Not Included)
7/16” Wrench
9/16” Wrench
3/4” Wrench
7/16” Socket and Socket Wrench
7/16"
#2 Phillips Head Screwdriver
®
Outdoor Patio Heater Model No. 200209
Assembly Instructions
1
DO NOT RETURN PRODUCT TO STORE.
For assistance call 1.800.762.1142 toll free. Please have your
owner’s manual and serial number available for reference.
2
Remove Base
Note: Retain these nuts as you will use them in another step.
For Easiest Assembly:
• To avoid losing any small components or hardware, assemble
your product on a hard level surface that does not have cracks
or openings.
• Clear an area large enough to layout all components and
hardware.
• When applicable, tighten all hardware connections by hand
first. Once the step is completed go back and fully tighten all
hardware.
• Follow all steps in order to properly assemble your product.
To complete assembly you will need:
• (1) Leak Detection Solution (Instructions on how to make
solution are included in step Operations Section)
• (1) Precision Filled LP Gas Grill Tank with Acme Type 1 external
threaded valve connection (4-5 gallon size)
Note: You must follow all steps to properly assemble heater.
Typical assembly: approximately 1 (one) hour.
G
3
4
Attach Legs
x3
Attach Weight Plate
F
D
J
x6
G
x6
I
x6
x1
x1
K
x1
page no.
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
5
Attach Platform
TIP: To tighten use a 7/16” wrench on Bolt and a 7/16” socket wrench on Nut.
D
J
7
x6
G
6
Insert Gas Line
x6
x6
Attach Shroud
8
Attach Engine Assembly
Note: One hole is at a different level than the rest. Make sure all holes line up
perfectly before
C
x4
5
®
Outdoor Patio Heater Model No. 200209
Assembly Instructions (continued)
9
11
Attach Engine Assembly/Post
Note: Make sure gas line comes out bottom of pole before securing engine to pole.
Note: Use the Allen Wrench to secure the post.
10
12
Attach Gas Line Clip
Side View
Attach Gas Line
Assemble Dome
Note: Each dome section has a pin mounted in the rolled bottom edge. If necessary
for proper alignment of dome sections, loosen each screw prior to assembly.
B
Gas Line Clip
Gas Line
Bottom View
A
B
x1
E
x3
H
x1
x1
page no.
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
13
G
15
14
Attach Dome Assembly
x3
Insert Battery
L
x1
Attach Control Knob
7
®
Outdoor Patio Heater Model No. 200209
Installing LP Gas Tank
To operate you will need (1) precision-filled standard grill LP gas
tank (20 lbs.) with external valve threads.
Operating Instructions
Checking for Leaks
Note: An empty standard grill LP gas tank weighs approximately
18 lbs. A precision-filled standard grill LP gas tank should weigh
no more than 38 lbs.
Burner Connections
Insert LP Gas Tank
If your unit was assembled for you, visually check the connection between the burner pipe and
orifice. Make sure the burner pipe fits over the orifice.
Place precision filled LP gas tank upright into hole in patio heater so it is arranged for vapor
withdrawal.
Make sure the regulator valve and hose connections are securely fastened to the burner and
the tank.
WARNING: Failure to inspect this connection or follow these
instructions could cause a fire or an explosion which can cause death,
serious bodily injury, or damage to property.
If the burner pipe does not rest flush to the orifice, please contact 1.800.762.1142 for
assistance.
Tank/Gas Line Connection
Make 2-3 oz. of leak solution by mixing one part liquid dishwashing soap with three parts
water.
Make sure control knobs are “OFF”.
Turn LP gas tank “ON” at valve.
Spoon leak check solution at all “X” locations
X
If any bubbles appear turn LP gas tank “OFF”, reconnect
and re-test. If you continue to see bubbles after several
attempts, disconnect LP gas source and contact
1.800.762.1142 for assistance.
If no bubbles appear after one minute turn tank “OFF”,
wipe away solution and proceed.
Secure LP Gas Tank
Secure tank in place by attaching loose end of tank restraint chain to hole in right leg.
LP Gas Line
Before Lighting
Heater should be thoroughly inspected before each use,
and by a qualified service person at least annually.
X
If relighting a hot heater, always wait at least 5 minutes.
Inspect the hose assembly for evidence of excessive
abrasion, cuts, or wear. Suspected areas should be
leak tested. If the hose leaks, it must be replaced prior
to operation. Only use the replacement hose assembly
specified by manufacturer.
X
X
X
X
LP Gas Tank Valve
Lighting
Note: this heater is equipped with a pilot light that allows for safer startups and shutdowns.
Pilot must be lit before main burner can be started.
1. Turn tank valve “OFF”.
2. Push control knob in and turn to “OFF”.
View Hole
3. Wait 5 minutes for any gas to clear.
4. Turn tank valve “ON”.
Connect LP Gas Tank
Before connecting, be sure that there is no debris caught
in the head of the LP gas tank, head of the regulator valve
or in the head of the burner and burner ports.
Connect gas line to tank by turning knob clockwise until it
stops.
Disconnect LP Gas Tank
Before disconnecting make sure the LP gas tank valve OFF.
Disconnect gas line to tank by turning knob
counterclockwise until it is loose.
5. Open viewing hole by sliding cover to
either side.
6. Push control knob in and rotate to pilot
position.
Note: for initial start or after any tank
change, hold control knob in for 2 minutes to
purge air from gas lines before proceeding.
7. Push igniter button once. Pilot light flame
will appear and be visible through viewing
hole.
8. Release control knob after 30 seconds.
Pilot light will remain lit. If not, return to
step 1.
9. Turn control knob to “HIGH”. Main burner
will light immediately. Flame is visible
through viewing hole. If not, return to
step 1.
10. If for some reason your ignitor fails
to deliver a spark, your heater can be
started by inserting a lit match through
the pilot view hole while pushing the
control knob in while in the pilot position.
Need a tank of gas? Try tank exchange service. It’s easy, fast, safe,
and available at tens of thousands of conveniently located retail outlets
nationwide. You can purchase a new full tank or exchange your empty for
a precision filled one.
WARNING: Be careful when
attempting to manually ignite
this heater. Holding in the
control know for more than 10
seconds before igniting the gas
will cause a ball of flame upon
ignition.
Control Knob
page no.
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
9
Cleaning and Care (continued)
Have a question or are having problems visit www.bluerhino.com or call 1.800.762.1142.
Cleaning Surfaces
Note: the burner may be noisy when initially turned on. To eliminate excessive noise from
the burner, turn the control knob to the pilot position. Then, turn the knob to the level of heat
desired.
1. Wipe surfaces clean with mild dishwashing detergent or baking soda.
2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush.
3. Rinse clean with water.
When heater is ON:
Emitter screen will become bright red due to intense heat. The color is more visible at night.
Note: While cleaning your unit, be sure to keep the area around the burner and pilot assembly
dry at all times. Do not submerge the control valve assembly. If the gas control is submerged
in water, do NOT use it. It must be replaced.
Burner will display tongues of blue and yellow flame. These flames should not be yellow or
produce thick black smoke, indicating an obstruction of airflow through the burners. The flame
should be blue with straight yellow tops.
Maintenance
If excessive yellow flame is detected, turn off heater and visit www.bluerhino.com or call
1.800.762.1142.
To enjoy years of outstanding performance from your heater, make sure you perform the
following maintenance activities on a regular basis:
1. Keep exterior surfaces clean.
Re-lighting
2. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean.
Signs of possible blockage include:
Note: For your safety, control knob cannot be turned
“OFF” without first depressing control knob in PILOT
position and then rotating it to “OFF”.
Gas odor with extreme yellow tipping of flame.
Heater does NOT reach the desired temperature.
1. Turn control knob to “OFF”.
Heater glow is excessively uneven.
2. Wait at least 5 minutes, to let gas dissipate, before
attempting to relight pilot.
Heater makes popping noises.
3. Repeat the “Lighting” steps.
Proper flame height.
Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than
normal. Frequently check for corroded areas and repair them promptly.
Shut Down
TIP: Use high-quality automobile wax to help maintain the appearance of your heater. Apply to
exterior surfaces from the pole down. Do not apply to emitter screen or domes.
1. Turn control knob clockwise to pilot. (Normally, burner will make a slight popping sound
when extinguished.) Burner will extinguish but pilot will remain “ON”.
Storage
2. To extinguish pilot, depress control knob and continue to turn it clockwise to “OFF”.
3. Turn tank valve clockwise to “OFF” and disconnect regulator when heater is not in use.
Between uses:
Note: After use, some discoloration of the emitter screen is normal.
1. Turn Control Knob OFF.
2. Disconnect LP source.
Cleaning and Care
3. Store heater upright in an area sheltered from direct contact with inclement weather (such
as rain, sleet, hail, snow, dust and debris).
CAUTION: All cleaning and maintenance should be done when patio
heater is cool and with the fuel supply disconnected.
4. If desired, cover heater to protect exterior surfaces and to help prevent build up in air
passages.
CAUTION: DO NOT clean any patio heater part in a self cleaning oven.
The extreme heat will damage the finish.
Note: Wait until heater is cool before covering.
Notices
1. Abrasive cleaners will damage this product.
2. Never use oven cleaner to clean any part of heater.
3. Do not clean any heater part in a self cleaning oven. The extreme heat will damage
the finish.
4. More frequent cleaning may be required as necessary. It is imperative that control
compartment, burners and circulating air passageways of the heater be kept clean.
5. Spiders and insects can create a dangerous condition that may damage heater or
make it unsafe. Keep burner area clean of all spiders, webs, or insects. Clean burner
holes by using a heavy-duty pipe cleaner. Compressed air may help clear away
smaller particles.
6. Inspect heater before each use.
7. Have heater inspected annually and repairs should be made by a qualified service
person.
8. Check heater immediately if any of the following conditions exist:
a. The smell of gas in conjunction with extreme yellow tipping of burner flames.
b. Heater does not reach proper temperature.
Note: At temperatures less than 40ºF, heat output will be reduced.
c. Heater’s glow is excessively uneven
d. Burner makes popping noises during use.
Note: A slight pop is normal when burner is extinguished.
9. Carbon deposits may create a fire hazard. Keep dome and emitter clean at all times.
10. Do not clean heater with combustible or corrosive cleaners. Use warm, soapy water.
11. Do not paint engine, engine access panel or dome.
12. This heater should be thoroughly cleaned on a regular basis.
13. After a period of storage and/or nonuse, check for leaks, burner obstructions and
inspect for any abrasion, wear, cuts to the hose.
During periods of extended inactivity or when transporting:
1. Turn Control Knob “OFF”.
2. Disconnect LP source and move to a secure, well-ventilated location outdoors.
3. Store heater upright in an area sheltered from direct contact with inclement weather (such
as rain, sleet, hail, snow, dust and debris).
4. If desired, cover heater to protect exterior surfaces and to help prevent build up in air
passages.
5. Never leave LP tank exposed to direct sunlight or excessive heat.
Note: Wait until heater is cool before covering.
®
Outdoor Patio Heater Model No. 200209
Product Registration
For faster warranty service, please register your product immediately at www.bluerhino.com or
call 1.800.762.1142.
Limited Warranty
Blue Rhino Global Sourcing, Inc (“Vendor”) warrants to the original retail purchaser of this
product, and to no other person, that if this product is assembled and operated in accordance
with the printed instructions accompanying it, then for a period of one (1) year from the date
of purchase, all parts in such product shall be free from defects in material and workmanship.
Vendor may require reasonable proof of your date of purchase. Therefore, you should retain
your sales slip or invoice. This Limited Warranty shall be limited to the repair or replacement of
parts, which prove defective under normal use and service and which Vendor shall determine
in its reasonable discretion upon examination to be defective. Before returning any parts, you
should contact Vendor’s Customer Service Department using the contact information listed
below. If Vendor confirms, after examination, a defect covered by this Limited Warranty in any
returned part, and if Vendor approves the claim, Vendor will replace such defective part without
charge. If you return defective parts, transportation charges must be prepaid by you. Vendor will
return replacement parts to the original retail purchaser, freight or postage prepaid.
This Limited Warranty does not cover any failures or operating difficulties due to accident,
abuse, misuse, alteration, misapplication, improper installation or improper maintenance or
service by you or any third party, or failure to perform normal and routine maintenance on
the product as set out in this owner’s manual. In addition, the Limited Warranty does not cover
damage to the finish, such as scratches, dents, discoloration, rust or other weather damage,
after purchase.
This Limited Warranty is in lieu of all other express warranties. Vendor disclaims all warranties
for products that are purchased from sellers other than authorized retailers or distributors,
including the warranty of merchantability or the warranty of fitness for a particular purpose.
VENDOR ALSO DISCLAIMS AND ANY ALL IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. VENDOR SHALL NO LIABILITY TO PURCHASER OR ANY THIRD PARTY FOR ANY
SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Vendor further
disclaims any implied or express warranty of, and assumes no responsibility for, defects in
workmanship caused by third parties.
This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other
rights depending upon where he or she lives. Some jurisdictions do not allow the exclusion or
limitation of special, incidental or consequential damages, or limitations on how long a warranty
lasts, so the above exclusion and limitations may not apply to everyone.
Vendor does not authorize any person or company to assume for it any other obligation or
liability in connection with the sale, installation, use, removal, return, or replacement of its
equipment, and no such representations are binding on Vendor.
Blue Rhino Global Sourcing, Inc
Winston-Salem, North Carolina 27105 USA
1.800.762.1142
page no.
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
Troubleshooting
If the problem is:
And this condition exists:
Then do this
Pilot won’t light
Tank valve is closed
Open valve
Blockage in orifice or pilot tube
Clean or replace orifice or pilot tube, visit www.bluerhino.com for
instructions.
Air in gas line
Open gas line and bleed it (pressing control knob in) for not more
than 1 - 2 minutes or until you smell gas
Low gas pressure with tank valve fully open
Turn tank valve “OFF” and replace tank
Igniter fails
Use match to light pilot; obtain new igniter and replace
Dirt built up around pilot
Clean dirt from around pilot
Connection between gas valve and pilot assembly is loose
Tighten connection and perform leak check
Thermocouple is not operating correctly
Replace thermocouple
Gas pressure is low
Turn tank valve “OFF” and replace tank
Blockage in orifice
Clear blockage
Control knob is not in “ON” position
Turn control knob to “ON”
Gas pressure is low
Turn tank valve “OFF” and replace tan
Outdoor temperature is less than 40ºF and tank is less than 1/4
full
Use a full tank
Supply hose is bent or kinked
Straighten hose
Control knob fully “ON”
Check burner and orifices for blockage
Gas pressure is low
Turn tank valvue “OFF” and replace tank
Note: Heater operates at reduced efficiency below 40ºF (5ºC).
Pilot won’t stay lit
Burner won’t light
Burner flame is low
Emitter glows uneven
Base is not on a level surface
Place heater on a level surface
Note: Bottom 1” of emitter normally does NOT glow.
Heater is level
Clean burner
Carbon build-up
Dirt or film on reflector and emitter
Clean reflector and emitter
Thick black smoke
Blockage in burner
Remove blockage and clean burner inside and outside
For more assistance please visit us online at www.bluerhino.com or call 1.800.762.1142 for immediate assistance.
Specifications
Certifications:
CSA International Requirement 5.90
Canadian National Standard CAN1-2.23-M82
Rating:
Maximum 40,000 BTU/hr. input
Heat Range:
Up to 20 foot diameter
Fuel:
Liquid Propane Gas (LP)
Tank Size:
Nominal 20 lb / 5 Gallon
Inlet gas supply pressure:
Maximum – 150 PSI
Minimum – 5 PSI
Manifold Pressure:
11.00 in. W.C.
Engine:
IPP E8
Safety Features:
100% Burner shut-off
Tilt Switch
Manufacturer:
Blue Rhino Global Sourcing, Inc
Made In:
China
Optional Accessories
Wheel Kit
For easier portability.
Patio Heater Cover
Helps protect your heater from insects and the elements.
Please call your local supplier for more information.
11
®
Outdoor Patio Heater Model No. 200209
Download PDF