Worx Sonicrafter WX681 Operating instructions

Worx Sonicrafter WX681 Operating instructions
SAFETY AND OPERATING MANUAL
High frequency multi-function tool
WX670 WX671
SAFETY INSTRUCTIONS
WARNING: Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for
future reference.
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1. WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable liquids,
gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose control.
2. ELECTRICAL SAFETY
a) Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep cord
away from heat, oil, sharp edges or
moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3. PERSONAL SAFETY
a) Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the influence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may result in
serious personal injury.
b) Use personal protective equipment.
Always wear eye protection.
Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position
before connecting to power source
and/or battery pack, picking up or
carrying the tool. Carrying power
tools with your finger on the switch or
energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your
hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of
dust collection can reduce dust-related
hazards.
High frequency multi-function tool
WX670 WX671
4. POWER TOOL USE AND CARE
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool will
do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the
switch does not turn it on and off.
Any power tool that cannot be controlled
with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories,
or storing power tools. Such preventive
safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the
reach of children and do not allow
persons unfamiliar with the power
tool or these instructions to operate
the power tool. Power tools are
dangerous in the hands of untrained
users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind
and are easier to control.
g) Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions and
the work to be performed. Use of the
power tool for operations different from
those intended could result in a hazardous
situation.
5. BATTERY TOOL USE AND CARE
a) Recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one type of
battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with
specifically designated battery packs.
Use of any other battery packs may create
a risk of injury and fire.
c) When battery pack is not in use, keep
it away from other metal objects, like
paper clips, coins, keys, nails, screws
or other small metal objects, that can
make a connection from one terminal
to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid
may be ejected from the battery;
avoid contact. If contact accidentally
occurs, flush with water. If liquid
contacts eyes, additionally seek
medical help. Liquid ejected from the
battery may cause irritation or burns.
6. SERVICE
a) Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
ADDITIONAL SAFETY
POINTS FOR YOUR TOOL
1. Never use your multi-sander for wet
sanding with accessories, also for
sawing, scraping, cutting, polishing, and
separating.
2. Always wear eye protection.
3. Always wear ear protection during
extended periods of operation..
4. Always wear a dust mask if the operation
is dusty.
5. Always inspect and remove all nails and
screws etc before sanding.
6. Always check walls and ceilings to avoid
hidden power cables and pipes. A metal
detector can be obtained from any good
DIY store for this purpose.
7. If possible, use clamping devices or other
suitable means to secure the workpiece to
a firm surface.
High frequency multi-function tool
WX670 WX671
8. Use the original accessories and the tool
provided, no others.
9. Only use accessories in good condition.
Do not use torn or worn accessories.
10. Do not use a damaged plug and cable, if
damaged have them repaired. Always be
aware of the cord location.
11. Do not abuse the cord. Never use the cord
to carry the tools or pull the plug from
the outlet. Keep cord away from heat, oil,
sharp edges or moving parts. Replace
damaged cords immediately.
12. Do not restart the cutting operation in the
workpiece, Let the tool reach full speed
and carefully reenter the cut.
13. Unplug your tools before mounting or
replacing accessories.
14. Do not “jam” the cut-off saw blade or
apply excessive pressure, Do not attempt
to make an excessive depth of cut.
15. Keep your hands away from cutting area.
Do not reach under the material being cut.
16. Hold power tools by insulated gripping
surfaces when performing an operation
where the cutting tool may contact hidden
wiring or its own cord. Contact with a
”live” wire will make exposed metal parts
of the tool “live” and shock the operator.
17. The operating instructions and the
enclosed safety information should be
kept carefully for later use and enclosed
with the machine, should it be passed on
or sold.
•
•
Work in a well-ventilated area.
Work with approved safety equipment,
such as those dust masks that are
specially designed to filter microscopic
particles.
WARNING! Whilst working
with this power tool, hand/arm
vibrations occur. Adopt the correct
working practices in order to reduce the
exposure to vibration.
CAUTION: Do not let familiarity
with your sander make you
careless. Remember that a careless fraction
of a second is sufficient to cause severe
injury.
WARNING!
Some dust created by power sanding,
sawing, grinding, drilling and other
construction activities contains chemicals
known to cause cancer, birth defects or other
reproductive harm. Some examples of these
chemicals are:
1) Lead from lead-based paint.
2) Crystalline silica from bricks and cement
and other masonry products.
3) Arsenic and chromium from chemicallytreated lumber.
Your risk from these exposures varies,
depending upon how often you do this type
of work. To reduce your exposure to these
chemicals:
High frequency multi-function tool
WX670 WX671
SYMBOLS
To reduce the risk of injury, user
must read instruction manual
Warning
Wear eye protection
Double insulation
Wear ear protection
Wear dust mask
WEEE marking
High frequency multi-function tool
WX670 WX671
�
�
��
�
�
�
�
�
�
�
1.
VARIABLE SPEED CONTROL (WX671)
2.
VENTING SLOTS
3.
SEGMENT SAW BLADE*
4.
STANDARD STRAIGHT CUTTER*
5.
ALLEN KEY
6.
FLANGE
7.
BOLT
8.
SANDING PAPER*
9.
SANDING PAD*
10. ON/OFF SWITCH
*Not all the accessories illustrated or described are included in standard delivery.
High frequency multi-function tool
WX670 WX671
TECHNICAL DATA
WX670
Rated voltage
WX671
220-240 V~50/60 Hz
Rated power
Oscillations speed
250 W
20000 /min
Oscillations angle
11000-20000 /min
3.2°
Protection class
/II
Weight
1.3 Kg
NOISE INFORMATION
A weighted sound pressure
85 dB (A)
A weighted sound power
96 dB (A)
KPA&KWA
3.0 dB (A)
Wear ear protection when sound pressure is over
85dB(A)
VIBRATION INFORMATION
Vibration total values (triax vector sum) determined according to EN 60745:
Typical weighted vibration
Vibration emission value ah = 5.42 m/s2
Uncertainty K = 1.5 m/s²
WARNING: The vibration emission value during actual use of the power tool can differ
from the declared value depending on the ways in which the tool is used dependant on
the following examples and other variations on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained.
The use the correct accessory for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any anti vibration accessories are used.
And the tool is being used as intended by its design and these instructions.
This tool may cause hand-arm vibration syndrome if its use is not adequately
managed.
WARNING: To be accurate, an estimation of exposure level in the actual conditions of
use should also take account of all parts of the operating cycle such as the times when
the tool is switched off and when it is running idle but not actually doing the job. This may
High frequency multi-function tool
WX670 WX671
significantly reduce the exposure level over the total working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and keep well lubricated (where
appropriate)
If the tool is to be used regularly then invest in anti vibration accessories.
Avoid using tools in temperatures of 100C or less.
Plan your work schedule to spread any high vibration tool use across a number of days.
ACCESSORIES
Allen key
Segment saw blade
Standard straight cutter
Sanding pad
Sanding paper (80,120,180# Each 2) WX670
Sanding paper (80,120,180# Each 5) WX671
1
1
1
1
6
15
We recommend that you purchase your accessories from the same store that sold you the
tool. Use good quality accessories marked with a well-known brand name. Choose the type
according to the work you intend to undertake. Refer to the accessory packaging for further
details. Store personnel can assist you and offer advice.
High frequency multi-function tool
WX670 WX671
OPERATION INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
1. MOUNTING THE TOOL (See A1.A2)
CAUTION: For all work or when changing
application tools,always wear protective
gloves. Danger of injury from the sharp edges of the
application tools. Application tools can become very
hot while working. Danger of burns!
WARNING: Do not let the segment saw blade
(3) and the straight cutter (4) face backwards
like A2, that may hurt user’s hand.
Unscrew the bolt (7).
Clean the tool holder, the application tool and the bolt
(7).
Place the application tool exactly onto the hexshaped tool holder. Pay attention that the application
tool has a flush fit.
Tighten the bolt (7) using the supplied Allen key.
2. MOUNTING / CHANGING THE SANDING
SHEET (See B)
Align the sanding sheet and press it
onto the sanding plate by hand.
Firmly press the power tool with the sanding sheet
against a flat surface and briefly switch the power
tool on. This provides for good adhesion and
prevents premature wear.
If one point has become worn, pull off the sanding
sheet, turn it through 120° and place it on again.
A1
A2
3. OPERATING THE ON/OFF SWITCH
— Switching the power tool ON:
Slide switch (10) forwards (I).
— Switching the power tool OFF:
Slide switch (10) backwards (0).
4. USING THE VARIABLE SPEED CONTROL
(WX671)
Select oscillation frequency while the motor is
running.
The variable speed control (1) can be used to set
the optimum oscillating frequency according to the
accessories used and the respective application.
High oscillation frequency:
Sanding, sawing, rasping and polishing stone and
metal.
Low oscillation frequency:
Polishing varnishes.
B
High frequency multi-function tool
WX670 WX671
C
5. SECURING THE WORK PIECE
CAUTION:Before working your tool make sure
that no live cables will be damaged.
WARNING: Do not touch the gear box after
long working time, because it could be hot.
Sanding
Typical application: wood, metal; small areas,
especially corners, edges and places difficult to
access.
Select high oscillation frequency (WX671).
Sanding with a constant movement and light
pressure.
Pressing on heavily does not increase the removal
– the sanding sheet merely becomes worn faster.
Sawing with the segment saw blade
Typical application: wood, plastics, sheet metal.
Select high oscillation frequency (WX671).
The saw blade lasts longer if the wear is distributed
evenly. To ensure an even distribution, loosen the
saw blade, turn it round a little and then tighten again
firmly.
Sawing with the standard straight cutter (see
C)
WARNING: The sawing teeth are very
sharp. Do not touch during mounting and
application.
The workpiece must be inserted firmly or
clamped tightly before it is processed.
Typical application: wood, plaster board and soft
plastics. Not suitable for metal (e. g. nails) and stone.
When plunging and sawing with a slight pendulum
motion, make sure that sufficient chip removal is
provided for.
High frequency multi-function tool
WX670 WX671
WORKING HINTS FOR
YOUR TOOL
ENVIRONMENTAL
PROTECTION
If your power tool becomes too hot,
especially when used at low speed, set the
speed to maximum and run it with no load
for 2-3 minutes to cool the motor. Avoid
prolonged usage at very low speeds. Always
keep the blade sharp.
Always ensure the work-piece is firmly held
or clamped to prevent movement.
Any movement of the material may affect the
quality of the cutting or sanding finish.
Start your tool before working and turn it off
only after you stop working.
Do not start sanding without having the
sandpaper fitted.
Do not allow the sandpaper to wear away it
will damage the base-plate. The guarantee
does not cover base-plate wear and tear.
Use coarse grit paper to sand rough surfaces,
medium grit for smooth surfaces and
fine grit for the final surfaces. If necessary,
first make a test run on scrap material.
Excessive force will reduce the working
efficiency and cause motor overload.
Replacing the accessory regularly will
maintain optimum working efficiency.
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authorities or retailer
for recycling advice.
MAINTENANCE
Remove the plug from the socket before
carrying out any adjustment, servicing
or maintenance.
Your power tool requires no additional
lubrication or maintenance. There are no
user serviceable parts in your power tool.
Never use water or chemical cleaners to
clean your power tool. Wipe clean with a
dry cloth. Always store your power tool in a
dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust.
Occasionally you may see sparks through the
ventilation slots. This is normal and will not
damage your power tool.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid a hazard.
PLUG REPLACEMENT
(UK & IRELAND ONLY)
If you need to replace the fitted plug then
follow the instructions below.
IMPORTANT
The wires in the mains lead are colored in
accordance with the following code:
BLUE =NEUTRAL
Brown = Live
As the colors of the wires in the mains lead of
this appliance may not correspond with the
colored markings identifying the terminals
in your plug, proceed as follows. The wire
which is colored blue must be connected
to the terminal which is marked with N.
The wire which is colored brown must be
connected to the terminal which is marked
with L.
WARNING: Never connect live or neutral
wires to the earth terminal of the plug. Only
fit an approved 13ABS1363/A plug and the
correct rated fuse.
NOTE: If a moulded plug is fitted and has
to be removed take great care in disposing
of the plug and severed cable, it must be
destroyed to prevent engaging into a socket.
13 Amp fuse approved
to BS1362
Connect
Blue to N
(neutral)
Outer sleeve
firmly clamped
High frequency multi-function tool
Brown L (live)
Cable grip
WX670 WX671
DECLARATION OF
CONFORMITY
We,
Positec Power Tools YO51 9NR, UK
Declare that the product,
Description
WORX High frequency multi-function
tool
Type WX670 WX671
Complies with the following Directives,
EC Machinery Directive 98/37/EC
EC Low Voltage Directive 2006/95/EC
EC Electromagnetic Compatibility Directive
2004/108/EC
Standards conform to
EN 55014-1
EN 55014-2
EN 61000-3-2
EN 61000-3-3
EN 60745-1
EN 60745-2-4
2008/05/08
Jacky Zhou
POSITEC Quality Manager
High frequency multi-function tool
WX670 WX671
Positec Power Tools (Europe) Ltd,
Positec House, Becklands Close,
Bar Lane Industrial Estate,
Boroughbridge, North Yorkshire,
YO51 9NR, UK.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement