FIRST AID

FIRST AID
For Selective Weed Control in Turf Sites Including
Residential and Institutional Lawns, Athletic Fields,
Commercial Sod Farms, Golf Course Fairways and
Roughs.
EPA Reg. No 279-3295
FIRST AID
If inhaled
EPA Est. 279-IL-1
Active Ingredient:
By Wt.
Sulfentrazone* ....................................................39.6%
Other Ingredients: .............................................. 60.4%
100.0%
*N-[2,4-dichloro-5-[4-(difluoromethyl)-4,5-dihydro-3-methyl-5-oxo-1H-1,2,4-triazol-1-yl]phenyl]methanesulfonamide.
Contains 4.0 pounds of active ingredient per gallon.
U.S. Patent No. 4,818,275
KEEP OUT OF REACH OF CHILDREN
CAUTION
See other panels for additional precautionary information.
If on skin or
clothing
If in eyes
If swallowed
• Move person to fresh air.
• If person is not breathing, call 911 or an ambulance, then give artificial respiration, preferably by
mouth-to-mouth, if possible.
• Call a poison control center or doctor for further
treatment advice.
• Take off contaminated clothing.
• Rinse skin immediately with plenty of water for 1520 minutes.
• Call a poison control center or doctor for further
treatment advice.
• Hold eye open and rinse slowly and gently with
water for 15-20 minutes.
• Remove contact lenses, if present, after the first 5
minutes, then continue rinsing eye.
• Call a poison control center or doctor for treatment
advice.
• Call a poison control center or doctor immediately for treatment advice.
• Do not give any liquid to the person.
• Do not induce vomiting unless told to do so by the
poison control center or doctor.
• Do not give anything by mouth to an unconscious
person.
HOTLINE NUMBER
Have the product container or label with you when calling a poison
control center or doctor, or going for treatment. You may also contact 1-800-331-3148 for emergency medical treatment information.
For Information Regarding the Use of this Product Call 1-800321-1FMC (1362).
PRECAUTIONARY STATEMENTS
Hazards to Humans (and Domestic Animals)
FMC Corporation
Agricultural Products Group
1735 Market Street
Philadelphia PA 19103
Net Contents:
2-25-08-C
CAUTION
Causes moderate eye irritation. Harmful if inhaled, swallowed, or
absorbed through skin. Avoid breathing vapor or spray mist. Avoid contact with skin, eyes or clothing.
Personal Protective Equipment (PPE)
Applicators and other handlers must wear: long-sleeved shirt and long
pants, waterproof gloves, and shoes plus socks.
Discard clothing and other absorbent materials that have been
drenched or heavily contaminated with this product. Do not reuse them.
Follow manufacturerʼs instructions for cleaning/maintaining PPE. If no
such instructions for washables, use detergent and hot water. Keep and
wash PPE separately from other laundry.
User Safety Recommendations:
Users should:
• Remove clothing immediately if pesticide gets inside. Then wash
thoroughly and put on clean clothing.
Page 1
This pesticide is toxic to marine/estuarine invertebrates. Do not apply
directly to water, to areas where surface water is present or to intertidal
areas below the mean high water mark. Drift and runoff may be hazardous to terrestrial and aquatic plants in neighboring areas. Do not
contaminate water when disposing of equipment washwaters or rinsate.
Groundwater advisory: This chemical is known to leach through soil into
groundwater under certain conditions as a result of label use. Use of
this chemical in areas where soils are permeable, particularly where the
water table is shallow, may result in groundwater contamination. Do not
use on coarse soils classified as sand which have less than 1% organic matter.
Surface water advisory: Sulfentrazone can contaminate surface water
through spray drift. Under some conditions, sulfentrazone may also
have a high potential for runoff into surface water (primarily via dissolution in runoff water), for several to many months post-application. These
include poorly draining or wet soils with readily visible slopes toward
adjacent surface waters, frequently flooded areas, areas overlying
extremely shallow groundwater, areas with in-field canals or ditches that
drain to surface water, areas not separated from adjacent surface
waters with vegetated filter strips, and areas over-lying tile drainage
systems that drain to surface waters.
Environmental Hazards
It is a violation of Federal Law to use this product in a manner inconsistent with its labeling.
Do not apply this product through any type of irrigation system.
Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in
the area during application. For any requirements specific to your state
or tribe, consult the agency responsible for pesticide regulation.
DIRECTIONS FOR USE
Use this product only in accordance with its labeling and with the
Worker Protection Standard, 40 CFR part 170. This standard contains requirements for the protection of agricultural workers on
farms, forests, nurseries, and greenhouses, and handlers of agricultural pesticides. It contains requirements for training, decontamination, notification, and emergency assistance. It also contains
specific instructions and exceptions pertaining to the statements on
this label about personal protective equipment (PPE) and restricted-entry interval. These requirements only apply to uses of this
product that are covered by the Worker Protection Standard.
Do not enter or allow worker entry into treated areas during the
restricted entry interval (REI) of 12 hours.
PPE required for early entry to treated areas that is permitted under
the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, is:
Coveralls over long-sleeved shirt and long pants, chemical-resistant gloves made of any waterproof material, and shoes plus socks.
Agricultural Use Requirements
The requirements in this box apply to uses of this product that are
NOT within the scope of the Worker Protection Standard for agricultural pesticides (40 CFR Part 170). The WPS applies when this
product is used to produce agricultural plants on farms, forests,
nurseries, or greenhouses.
Re-entry Statement: Do not allow people (other than applicator) or
pets on treatment area during application. Do not enter treatment
area until spray has dried.
Non-Agricultural Use Requirements
Page 2
Do not contaminate water, food of feed by storage or disposal.
Pesticide Storage
Store product in original container only, away from other pesticides, fertilizer, food or feed. Store in a cool, dry place and avoid
excess heat.
In case of spill, avoid contact, isolate area and keep out animals
and unprotected persons. Confine spills. Call FMC: (800) 3313148.
To confine spill: If liquid, dike surrounding area or absorb with
sand, cat litter or commercial clay. If dry material, cover to prevent
dispersal. Place damaged package in a holding container. Identify
contents.
Pesticide Disposal
If these wastes cannot be disposed of by use according to label
instructions, contact your State Pesticide or Environmental Control
Agency or the Hazardous Waste representative at the nearest
EPA Regional office for guidance.
Container Disposal
Triple rinse (or equivalent). Then offer for recycling or reconditioning, or puncture and dispose of in a sanitary landfill, or incineration, or if allowed by state and local authorities, by burning. If
burned, stay out of smoke.
STORAGE AND DISPOSAL
GENERAL INFORMATION
Dismiss turf herbicide is a selective post emergence herbicide which
controls broadleaf weeds and sedges in established turf areas including, but not limited to, residential and institutional lawns, athletic fields,
commercial sod farms, golf course fairways and golf course roughs.
Dismiss turf herbicide is formulated as a flowable (suspension concentrate) containing 4 lbs of active ingredient per gallon. The mode of action
of Dismiss turf herbicide involves uptake by both weed roots and
shoots.
Turf Use Instructions
Mixing and Application Instructions
General handling instructions
This product may not be mixed or loaded within 50 feet of any wells
(including abandoned wells and drainage wells), sink holes, perennial or
intermittent streams and rivers, and natural or impounded lakes and
reservoirs. This setback does not apply to properly capped or plugged
abandoned wells and does not apply to impervious pad or properly
diked mixing/loading areas.
Operations that involve mixing, loading, rinsing or washing of this product into or from pesticide handling or application equipment or containers within 50 feet of any well, are prohibited unless conducted on an
impervious pad constructed to withstand the weight of the heaviest load
that may be positioned on or moved across the pad. Such a pad shall
be designed and maintained to contain any product spills or equipment
leaks, container or equipment rinse or wash water, and rainwater that
may fall on the pad. Surface water shall not be allowed to either flow
over or from the pad, which means the pad must be self contained. The
pad shall be sloped to facilitate material removal. An unroofed pad shall
be of sufficient capacity to contain at a minimum 110% of the capacity
of the largest pesticide container or application equipment on the pad.
A pad that is covered by a roof of sufficient size to completely exclude
precipitation from contact with the pad shall have a minimum containment capacity of 100% of the capacity of the largest pesticide container or application equipment on the pad. Containment capacities as
described above shall be maintained at all times. The above specific
minimum containment capacities do not apply to vehicles when delivering pesticide shipments to the mixing/loading site. States may have in
effect additional requirements regarding wellhead setbacks and operational containment.
Product must be used in a manner which will prevent back siphoning in
wells, spills or improper disposal of excess pesticide, spray mixtures or
rinsates.
SPRAY TANK PREPARATION
It is important that spray equipment is clean and free of existing pesticide deposits before using this product. Follow the spray tank clean out
procedures specified on the label of product previously applied before
adding Dismiss turf herbicide to the tank.
Dismiss turf herbicide is a suspension concentrate intended for dilution
with water. In certain applications, liquid fertilizer may replace water as
diluent.
MIXING WITH WATER
For best results, fill spray tank with one fourth of the volume of clean
water needed for the area to be treated. Start the agitation system and
add Dismiss turf herbicide to the tank. Make sure Dismiss turf herbicide
is thoroughly mixed before application or before adding another product
to the spray tank.
USE OF SURFACTANTS
Temporary discoloration of some turf types may result from use of surfactants or adjuvants with Dismiss Turf Herbicide. High temperatures
and high relative humidity may increase the risk of temporary discoloration. Use of surfactants is not recommended.
MIXING WITH LIQUID FERTILIZERS
Utilize local recommendations for sources and rates of fertilizer and
refer to mixing directions on the fertilizer labels (e.g. UAN or urea solutions). Determine the compatibility of this product with the desired fluid
fertilizer by mixing small proportional quantities in advance (See the
“TANK MIXTURES COMPATIBILITY” section below)
TANK MIXTURES COMPATIBILITY
Dismiss turf herbicide is believed to be compatible with most herbicides,
fungicides, insecticides, growth regulators, liquid fertilizers and spray
adjuvants commonly used in turf and ornamental plant management.
However, when preparing a new tank mix conduct an appropriate compatibility test by mixing proportional amounts of all spray ingredients in
a test vessel (jar) prior to tank mixing with other products. Shake the
mixture vigorously and allow it to stand for five to ten minutes. Rapid
precipitation of the ingredients and failure to re-suspend when shaken
indicates that the mixture is incompatible and should not be applied.
Provided the jar test indicates the mixture to be compatible, prepare the
tank mixture as follows: Fill the tank one fourth full with water. With the
agitator operating, add the recommended amounts of ingredients using
the following order: dry granules first, and liquid suspensions (flowables) second. As the agitation continues and the tank is filled with
water add EC products third followed by the addition of water soluble
products.
Read and observe mixing instructions of all tank mix partners. Also read
each productʼs label for Directions for Use, Precautionary Statements
and Restrictions and Limitations. The most restrictive labeling applies in
all tank mixtures. No label dosage rate should be exceeded. Tank mixture recommendations are for use only in states where the companion
products and application site are registered. In addition, certain states
or geographical regions may have established dosage rate limitations.
Consult your state Pesticide Control Agency for additional information
regarding the maximum use rates.
Use Dismiss turf herbicide spray mixture immediately after mixing. Do
not store the mixture.
Ground Equipment
Power sprayers: Uniform and accurate spray coverage requires proper
calibration and operation of spray equipment. The use of marker dyes
or foams can improve application accuracy. Boom sprayers equipped
with appropriate flat fan nozzles, tips and screens are ideal for broadcast applications. Power sprayers fitted with spray wand/gun may also
be used for broadcast application after careful calibration by the applicator. Power sprayers fitted with spray wand/gun are suitable for spot
treatments.
Hand operated sprayers: Backpack and compression sprayers are
appropriate for small turfgrass areas and spot treatments. Wands fitted
with a flat fan nozzle tip should be held stationary at the proper height
during application. A side to side or swinging arm motion can result in
uneven coverage.
Apply this product in a sufficient volume of carrier solution to provide a
uniform spray distribution. Spray volumes of 20 – 175 gallons per acre
(0.5 to 4.0 gal/1,000 sq ft) with spray pressures adjusted to 20 – 40 psi
are appropriate. Apply the higher spray volumes for dense weed populations.
Sprayer Equipment Clean-Out
After spraying Dismiss turf herbicide and before using sprayer
equipment for any other applications, the sprayer must be thoroughly cleaned using the following procedure:
1. Drain sprayer tank, hoses, and spray boom and thoroughly rinse the
inside of the sprayer tank with clean water to remove sediment and
residues. In addition, thoroughly flush sprayer hoses, boom, and nozzles with clean water.
2. Fill the tank 1/2 full with clean water, and add appropriate detergent
or ammonia (follow manufacturerʼs directions for use). Fill the tank to
capacity and operate the sprayer for 15 minutes to flush hoses, boom,
and nozzles.
3. Drain the sprayer system. Rinse the tank with clean water and flush
through the hoses, boom, and nozzles. Remove and clean spray tips
and screens separately.
4. Properly dispose of all cleaning solution and rinsate in accordance
with Federal, State and local regulations and guidelines.
Do not drain or flush equipment on or near desirable trees or plants. Do
not contaminate any body of water including irrigation water that may be
used on other plants.
Weed Control in Turfgrasses
Use Precautions for Turf Use
This product may be used on seeded, sodded or sprigged turgrasses
that are well established. First application of this product can be made
following the second mowing providing the turfgrass has developed into
a uniform stand with a good root system. Turfgrass injury could result
from application of this product on turfgrass that is not well established
Turfgrass Safety
or has been weakened by stresses such as unfavorable weather conditions, disease, chemical or mechanical influences.
When applied as directed under the conditions described, the following
established turfgrasses are tolerant to Dismiss turf herbicide at the recommended use rates in a range from 0.125 to 0.375 lb a.i./acre (4 to 12
fl. oz/acre or 0.092 to 0.275 fl. oz./1,000 sq. ft).
Table 1. Tolerant grasses.
Maximum Use Rate
Grass Type*
Single Application
Fluid ounces Fluid ounces
per
per
1000 ft2
acre
Cool Season Grasses
lb ai/A
Bentgrass, creeping (Agrostis sp.)
0.125 - 0.092 - 0.18
.25
4-8
0.25 - 0.18 - 0.275
0.375
8 - 12
Bluegrass, Kentucky (Poa pratensis)
Bluegrass, Rough2 (Poa trivialis)
Fescue, fine1 (Festuca rubra)
Fescue, tall1 (Festuca arundinacea)
Ryegrass, perennial (Lolium perenne)
0.125
0.092
4
Warm Season Grasses
Bahiagrass2 (Paspalum notatum)
Bermudagrass (Cynodon dactylon) & hybrids
Buffalograss (Buchloe dactyloides)
Carpetgrass (Axonopus affinis)
Centipedegrass (Eremochloa ophuiroides)
Kikuyugrass (Pennisetum clandestinum)
Seashore Paspalum (Paspalum vaginatum)
St.Augustinegrass (Stenotaphrum secundatum) 2
Zoysiagrass (Zoysia japonica)2
Use of this product on certain cultivars of Chewings Fescue, Fine Fescue or Tall
Fescue cultivars may result in undesirable injury.
2
Dismiss Turf Herbicide application may cause temporary discoloration to exposed
leaf surfaces on St. Augustinegrass and certain cultivars of zoysiagrass bahiagrass,.or rough bluegrass. Treated turfgrass will recover with new growth.
Discolored leaf tissue will be removed with mowing. To reduce potential for discoloration, do not apply Dismiss Turf Herbicide on turfgrass that is weakened by
weather, mechanical, chemical, disease or other related stress. Maintain proper
cultural practices such as adequate moisture and fertility levels to promote healthy
turf growth.
*Dismiss Turf Herbicide has demonstrated tolerance on both cool and warm season turfgrasses. However, not all varieties have been evaluated. Turfgrass managers desiring to treat newly released varieties should first apply Dismiss Turf
Herbicide to a small area prior to treatment of larger areas.
1
Application to reseeded, overseeded or sprigged areas:
Reseeding, overseeding or sprigging of treated areas within one (1)
month after application of this product could inhibit the establishment of
desirable turfgrasses. Overseeding of bermudagrass with perennial ryegrass at two (2) to four (4) weeks after an application can be done if
slight injury to perennial ryegrass can be tolerated.
Best results are obtained for reseeding or overseeding when mechanical or power seeding equipment (slit seeders) are used to give good
seed to soil contact and proper soil cultivation, irrigation and fertilization
practices are followed.
Sod Production:
This product may be applied to established sod. Allow sod to establish
a good root system, a uniform stand and to fill in the exposed edges. It
is recommended that sod be established for at least three (3) months
before an application of Dismiss turf herbicide.
Do not apply this product within three (3) months of harvest.
Other Use Precautions:
Do not apply to golf course putting greens or tees.
Do not use on turfgrasses other than those listed on this label.
Do not apply with surfactants unless previous experience has demonstrated combinations with surfactant to be physically compatible and
non-injurious to the grass type in question.
Do not graze or feed livestock forage cut from areas treated with
Dismiss turf herbicide.
Do not apply directly to landscape ornamentals or ornamental beds.
Temporary turfgrass discoloration has been observed when Primo has
been either tank-mixed or applied within 7 days of a Dismiss Turf
Herbicide application. It is recommended that Primo applications be
made 7 days prior to, or after Dismiss Turf Herbicide application to
reduce risk of turfgrass discoloration.
POSTEMERGENCE CONTROL OF ANNUAL AND PERENNIAL
SEDGES INCLUDING NUTSEDGES
Dismiss turf herbicide will control or suppress sedges (Table 2) when
applied at a rate of 4 to 12 fl oz/acre (0.092 to 0.275 fl. oz./1,000 sq. ft.).
Apply the highest rate consistent with the rate needed for turfgrass safety in Table 1. Rates lower than 12 fl oz/acre (0.275 fl. oz/1,000 sq. ft.)
will generally control sedges for at least 60 days.
Good spray coverage is needed for optimum control of sedges.
Temporary discoloration of some turfgrass species may result from use
of surfactant. Use of surfactants is not recommended.
Page 3
Table 2. Sedge species controlled or suppressed by Dismiss turf
herbicide
Common Name
Kyllinga, green
Kyllinga, false green
Nutsedge, purple1
Nutsedge, yellow
Sedge, cylindrical
Sedge, globe
Sedge, Surinam
Sedge, Texas
SCIENTIFIC NAMES
(Kyllinga brevifolia)
(Kyllinga gracillima)
(Cyperus rotundus)
(Cyperus esculentus)
(Cyperus retrorsus)
(Cyperus globulosus)
(Cyperus surinamensis)
(Cyperus polystachyos)
1
PURPLE NUTSEDGE; For optimum control of purple nutsedge, split applications
are recommended (Table 3). Apply 4-8 ounces per acre as an initial application followed by a second application when evidence of actively growing purple nutsedge
is visible. Do not exceed the maximum rate per acre based on turfgrass variety
listed in Table 1; Tolerant grasses.
Table 3
Grass Type
Cool Season Grasses
excluding Bentgrass
(see Table 1)
Split Application Rate Options
Option 1
Option 2
(fluid ounces/acre)
(fluid ounces/acre)
Warm Season Grasses
(see Table 1)
4 oz followed by
4 oz 35 DAIT
8 oz followed by
4 oz 35 DAIT
DAIT = Days After Initial Treatment
6 oz followed by
2 oz 35 DAIT
6 oz followed by
6 oz 35 DAIT
POSTEMERGENCE CONTROL OF GRASSY WEEDS
Dismiss Turf Herbicide will control or suppress specific annual Grasses
(Table 4) when applied at a rate of 4 to 12 fl oz/acre (0.092 to 0.275 fl.
oz./1,000 sq. ft.). Apply the highest rate consistent with the rate needed
for turfgrass tolerance in Table 1. Rates lower than 12 fl oz/acre (0.275
fl. oz/1,000 sq. ft.) will generally control grasses for at least 60 days.
Dismiss Turf Herbicide works best if applied when the annual grasses
are small (pre tiller stage) and actively growing.
Good spray coverage is needed for optimum control of grasses.
Temporary discoloration of some turfgrass species may result from use
of surfactant. Use of surfactants is not recommended.
Table 4
Common Name
Goosegrass
Scientific Name
Eleusine indica
BROADLEAVES
Bedstraw, catchweed
Beggarweed, Florida
Bittercress
Black medic
Buttercups
Carolina geranium
Carpetweed
Chickweed, common
Chickweed, mouseear
Cinquefoil
Clover
Copperleaf
Cudweed
Dandelion
Dock, Curly
Dollarweed
Eclipta
Evening primrose
Fiddleneck
Filaree
Galinsoga
Goldenrod
SCIENTIFIC NAMES
(Galium aparine)
(Desmodium tortuosum)
(Cardamine spp.)
(Medicago lupulina)
(Ranunculus spp.)
(Geranium carolinianum)
(Mollugo verticillata)
(Stellaria media)
(Cerastium vulgatum)
(Potentilla spp.)
(Trifolium spp.)
(Ascalypha spp.)
(Gnaphalium spp.)
(Taraxacum officinale)
(Rumex crispus)
(Hydrocotyl umbellata)
(Eclipta prostrata)
(Oenothera biennis)
(Amsinckia spp.)
(Erodium spp.)
(Galinsoga ciliate)
(Solidago spp.)
POSTEMERGENCE CONTROL OF ANNUAL, BIENNIAL & PERENNIAL BROADLEAF WEEDS
Dismiss turf herbicide will control or suppress the weeds listed in Table
3 when applied alone shortly after weeds have emerged. Apply Dismiss
turf herbicide at rates from 4 to 12 fl. oz/acre (0.092 to 0.275 fl. oz./1,000
sq. ft.). Do not exceed the application rate specified for the turfgrass
species in Table 1. To broaden the weed spectrum and increase effectiveness for certain weeds listed in Table 5, Dismiss turf herbicide may
be tank mixed with other EPA registered postemergence herbicides.
Read the label recommendations of the tank mix partner to determine
turfgrass species safety, use rate and application procedures. Follow all
label restrictions, use directions and precautionary statements before
using these tank mixtures. Read and follow the “TANK MIXTURES
COMPATIBILITY” section of this label for instructions on how to determine the compatibility of tank mixtures.
When used as directed Dismiss turf herbicide will control or suppress
the following weeds.
Table 5. Weeds controlled or suppressed by Dismiss turf herbicide
Page 4
Table 5. (Continued)
BROADLEAVES
Ground ivy
Groundsel, common
Henbit
Knawel
Knotweed, prostrate
Kochia
Lambsquarters, common
Lawn burweed (spurweed)
Lespedeza, common
Mallow, common
Parsley piert
Pigweed, Redroot
Pigweed, Smooth
Pigweed, Tumble
Pineapple weed
Plantain, buckhorn
Puncture weed
Purslane, common
Pusley, Florida
Redweed
Rocket, London
Shepherdʼs purse
Smartweed, Pennsylvania
Sorrel, Red
Speedwell
Spurge, (annuals)
Spurge, prostrate
Spurge, spotted
Star of Bethlehem
Velvetleaf
Violet, wild
Violet, Johnny-jump-up
Wild garlic
Wild onion
Woodsorrel, creeping
Woodsorrel, yellow
SCIENTIFIC NAMES
(Glechema hederacea)
(Senecio vulgaris)
(Lamium amplexicaule)
(Scleranthus annuus)
(Polygonum aviculare)
(Kochia scoparia)
(Chenopodium album)
(Soliva pterosperma)
(Lespedeza striata)
(Malva neglecta)
(Alchemilla arvensis)
(Amaranthus retroflexus)
(Amaranthus hybridus)
(Amaranthus albus)
(Matricaria matricarioides)
(Plantago lanceolata)
(Tribulus terrestris)
(Portulaca oleracea)
(Richardia scabra)
(Melochia corchorifolia)
(Sisymbrium irio)
(Capsella bursa-pastoris)
(Polygonum pensylvanicum)
(Rumex acetosella)
(Veronica spp.)
(Euphorbia spp.)
(Euphorbia humistrata)
(Euphorbia maculata)
(Ornithogalum umbellatum)
(Abutilon theophrasti)
(Viola pratincola)
(Viola rafeinesquii)
(Allium vineale)
(Allium canadense)
(Oxalis corniculata)
(Oxalis stricta)
Conditions of Sale and Limitation of Warranty and Liability:
NOTICE: Read the entire Directions for Use and Conditions of Sale
and Limitation of Warranty and Liability before buying or using this
product. If the terms are not acceptable, return the product at once,
unopened, and the purchase price will be refunded.
The Directions for Use of this product must be followed carefully. It is
impossible to eliminate all risks inherently associated with the use of
this product. Crop injury, ineffectiveness, or other unintended consequences may result because of such factors as manner of use or application, weather or crop conditions beyond the control or FMC or Seller.
All such risks shall be assumed by Buyer and User, and Buyer and
User agree to hold FMC and Seller harmless for any claims relating to
such factors.
Seller warrants that this product conforms to the chemical
description on the label and is reasonably fit for the purposes stated on the Directions for Use when used in accordance with the
directions under normal conditions of use. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, FMC MAKES NO WARRANTIES
OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR
PURPOSE, NOR ANY OTHER EXPRESS OR IMPLIED WARRANTIES WITH RESPECT TO THE SELECTION, PURCHASE, OR
USE OF THIS PRODUCT. Any warranties, express or implied, having been made are inapplicable if this product has been used contrary to label instructions, or under abnormal conditions, or under
conditions not reasonably foreseeable to (or beyond the control
of) seller or FMC, and buyer assumes the risk of any such use.
To the extent consistent with applicable law, FMC or seller shall not be
liable for any incidental, consequential or special damages resulting
from the use or handling of this product. TO THE EXTENT CONSISTENT WITH APPLICABLE LAW, THE EXCLUSIVE REMEDY OF THE
USER OR BUYER, AND THE EXCLUSIVE LIABILITY OF FMC AND
SELLER FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES (INCLUDING CLAIMS BASED ON BREACH OF WARRANTY,
CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT, SHALL BE THE RETURN OF THE PURCHASE PRICE OF THE
PRODUCT OR, AT THE ELECTION OF FMC OR SELLER, THE
REPLACEMENT OF THE PRODUCT.
This Conditions of Sale and Limitation of Warranty and Liability may not
be amended by any oral or written agreement.
FMC – Trademark of FMC Corporation
© FMC Corporation 2008
Page 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement