IC693MDL733

IC693MDL733
This Datasheet is for the
IC693MDL733
12/24 Volt DC Negative Logic 0.5 Amp Output - 8 Point
http://www.cimtecautomation.com/parts/p-14666-ic693mdl733.aspx
Provides the wiring diagrams and installation guidelines for this GE Series 90-30
module.
For further information, please contact Qualitrol Technical Support at
1-800-784-9385
[email protected]
7
12/24 Volt DC Negative Logic 0.5 Amp Output - 8 Point
IC693MDL733
The 12/24 volt DC Negative Logic 0.5 Amp Output module for the Series 90-30 Programmable
Logic Controller provides 8 output points in one group with a common power output terminal.
This output module is designed to have negative logic characteristics in that it sinks current
from the loads to the user common or negative power bus. The output device is connected
between the positive power bus and the module output. The output characteristics are
compatible with a wide range of user-supplied load devices, such as: motor starters, solenoids,
and indicators. Power to operate the field devices must be supplied by the user.
LED indicators which provide the ON/OFF status of each point are located at the top of the
module. This LED block has two horizontal rows with eight green LEDs in each row; the top
row labeled A1 through 8 (points 1 through 8) is used by this module. An insert goes between
the inside and outside surface of the hinged door. The surface towards the inside of the module
(when the hinged door is closed) has circuit wiring information, and circuit identification
information can be recorded on the outside surface. The outside left edge of the insert is
color-coded blue to indicate a low-voltage module. There are no fuses on this module.
This module can be installed in any I/O slot of a 5 or 10-slot baseplate in a Series 90-30 PLC
system.
Table 7-10. Specifications for IC693MDL733
Rated Voltage
Output Voltage Range
12/24 volts DC
12 to 24 volts DC (+20%, –15%)
Outputs per Module
Isolation
8 (one group)
1500 volts between field side and logic side
Output Current
0.5 amps maximum per point
2 amps maximum per common
Output Characteristics
Output Voltage Drop
Off-state Leakage
On Response Time
Off Response Time
0.5 volts maximum
1 mA maximum
2 ms maximum
2 ms maximum
Power Consumption
50 mA (all outputs on) from 5 volt bus on backplane
Refer to Appendix B for product standards and general specifications.
7-20
Series 90-30 PLC I/O Module Specifications – July 2000
GFK-0898F
Discrete Output Modules
7
IC693MDL733 Output Module Field Wiring Information
The following figure provides wiring information for connecting user supplied load devices
and power source to the 8 point 12/24 volt DC negative logic 0.5 amp output module.
a45118
MODULE CIRCUITRY
TERMINALS
FIELD WIRING
1
2
A1
4
A3
6
A5
8
A7
3
A2
5
A4
7
1 µf
A6
9
A8
+
10
OTHER
CIRCUITS
NC
11
12
13
NC
NC
14
15
NC
NC
16
17
NC
NC
18
19
NC
NC
20
NC
Figure 7-18. IC693MDL733 Output Module Field Wiring
a45051
2.0
TOTAL 1.5
MODULE
LOAD
CURRENT 1.0
(AMPS)
0.5
10°C
20°C
30°C
40°C
50°C
60°C
AMBIENT TEMPERATURE (°C)
Figure 7-19. Load Current vs. Temperature for IC693MDL733
GFK-0898F
Chapter 7 – Discrete Output Modules
7-21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement