Miele | G 7855 | Operating instructions | Miele G 7855 Operating instructions

Operating instructions
Commercial dishwasher
G 7855
To avoid the risk of accidents or
damage to the machine it is
essential to read these operating instructions
before it is installed, commissioned and used for the
first time.
G i
M.-Nr. 05 234 481
Contents
Description of the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Guide to the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Before using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Opening and closing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setting the water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Filling the salt reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Salt indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Loading the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Loading the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Adjusting the top basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Items not suitable for dishwashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Adding rinsing agent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Setting the dosage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Adding cleaning agent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Selecting a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Starting a programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Changing a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Selecting an additional function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Programme sequence indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Switching off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
To cancel a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Programming special functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Correcting minor faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Customer service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
2
Description of the machine
This Miele machine is a front-loading
commercial dishwasher, with very short
batch times. It is especially suitable for
use in cafes, fast food outlets,
restaurants, guest houses etc.
It operates on the freshwater system
and is equipped with a water softener
as standard.
3
Guide to the machine
a On/Off button (I-0)
b Door release button
j Optical interface
( for Service Technician use only)
d Delay start indicator light (see
Programming special functions)
k Add liquid cleaning agent indicator
light (only applies to machine fitted
with an optional external DOS
module)
e Drying indicator light
l Add rinsing agent indicator light
f Programme start indicator light
m Add salt indicator light
g Start button
n Water inlet / Drain indicator light
h Drying button
o Programme sequence indicators
i Button to change between the
current temperature and elapsed
time in the display
p Programme selector
c Display
4
Guide to the machine
a Connection for DOS module
(optional dispenser pump for liquid
cleaning agent) at the rear of the
machine
d Dispenser for powder cleaning agent
e Rinsing agent reservoir
(with dosage selector)
b Filter combination
c Salt reservoir
(for the water softener)
5
Warning and Safety instructions
This machine complies with all
relevant local and national safety
requirements. Incorrect use can lead
to personal injury and damage to
property.
Read the operating instructions
carefully before starting to use this
machine. This way you will avoid the
risk of accidents and damage to the
machine.
Keep these instructions in a safe
place for reference, and pass them
on to any future user.
Please pay attention to the following
notes to avoid injury and damage.
This machine should be
commissioned and then maintained
by a Miele authorised and trained service technician or other suitably qualified
and competent approved person.
Repairs and other work by unqualified
persons could be dangerous.
Do not install the machine in an
area where there is any danger of
explosion or of freezing conditions.
This machine is designed for
commercial use only, as described
in these Operating Instructions.
Alterations to the machine, or using it
for purposes other than those for which
it was designed, are unauthorised and
could cause harm. The manufacturer
cannot be held liable for damage
caused by improper or incorrect use of
the machine.
The electrical safety of this
machine can only be guaranteed if
connected to a correctly installed
earthing system on site. It is imperative
that this basic safety requirement is
tested regularly and, where there is any
doubt, the electrical wiring system on
site should be inspected by a qualified
electrician.
The manufacturer cannot be held liable
for damage or injury caused by the lack
of or inadequacy of an effective
earthing system (e.g. electric shock).
This equipment may only be
installed in mobile installations
such as ships, oil rigs etc. if a risk
assessment of the installation has been
carried out by a suitably qualified
engineer.
A damaged machine is dangerous.
Switch off at the mains immediately
and call the Miele Service Department
or an authorised and trained Miele Service Dealer or other suitably qualified
and competent approved person.
Correct use
6
Warning and Safety instructions
Personnel operating the machine
should be trained regularly.
Untrained personnel should not be
allowed access to the machine or its
controls.
This machine is not a toy! Do not
allow children to play in or around
it, or to operate it. There is a danger
they could injure themselves, or get into
the machine and lock themselves in.
Take great care when handling
liquid agents and additives. These
may contain irritant or corrosive
ingredients. Do not use organic
solvents as these could cause an
explosion.
Follow all relevant safety procedures
carefully. Wear protective gloves and
goggles. With all chemical agents, the
manufacturer’s safety conditions must
be observed.
Avoid inhalation of powder
cleaners. They can cause burning
in the mouth and throat if swallowed,
and can inhibit breathing.
The water in the machine must not
be used as drinking water.
Do not sit or lean on an open door.
The machine could tip up and be
damaged, or cause an injury.
Be careful when sorting items with
sharp pointed ends and
positioning them in the machine that
you do not hurt yourself or create a
danger for others. Sharp knives etc.
should be placed in the baskets with
the pointed end facing downwards.
When using this machine in the
higher temperature ranges be
especially careful not to scald or burn
yourself when opening the door.
Baskets and inserts must be allowed to
cool down before they are unloaded.
Any water remaining in containers
could still be very hot. Empty them into
the wash cabinet before taking them
out.
Do not touch the heating elements
if you open the door during or
directly after the end of a programme:
you could burn yourself. They remain
hot for some time after the end of the
programme.
Never clean the machine or near
vicinity with a water hose or a high
pressure hose.
Before any maintenance or repair
work is carried out, the machine
must be disconnected from the mains
supply by switching off at the mains
isolator or withdrawing the mains fuse.
The following points should be
observed to assist in maintaining
quality standards, to protect users,
and to avoid damage to the machine
and items being cleaned.
Only use Miele approved cleaning
agents in this machine. Use of
unsuitable cleaning agents could
adversely affect the components of the
machine as well as items being
cleaned.
Foam can have an adverse effect
on the cleaning process. Only use
low-foaming cleaning agents which
have been approved by Miele. Some
types of soiling can also cause foaming
to occur.
7
Warning and Safety instructions
Where a chemical additive is
recommended on technical
application grounds (e.g. a cleaning
agent), this does not imply that the
manufacturer of the machine accepts
liability for the effect of the chemical on
the items being cleaned.
Please be aware that changes in
formulation, storage conditions etc.
which may not be publicised by the
chemical manufacturer, can have a
negative effect on the cleaning result.
When using cleaning agents and
special application products, it is
essential that the manufacturer’s
instructions are followed. Only use such
products for the purpose and in the
situation specifed to avoid such
dangers as chemical reactions and
material damage.
The machine is designed for
operation with water and additive
cleaning agents only. Organic solvents
must not be used in this machine, as
there is the danger under certain
circumstances of fire or explosion.
(Although this is not the case with all
organic solvents, other problems could
arise with their use, for example
damage to rubber and synthetic
materials).
In critical applications where very
stringent requirements have to be
met, it is strongly recommended that all
the relevant factors for the process,
such as cleaning agents, water quality
etc., are discussed with the Miele
Application Technology specialists.
8
If cleaning and rinsing results are
subject to particularly stringent
requirements (e.g. chemical analysis,
specialised industrial processes etc.), a
regular quality control test must be
carried out by the user to ensure that
required standards of cleanliness are
being achieved.
The special inserts should only be
used for their specific application.
Empty any containers or utensils
before arranging them in the
machine.
Do not allow any remains of acids
or solvents, and in particular
hydrochloric acid or chloride solutions,
to get into the wash cabinet. Similarly
avoid any materials with a corrosive
effect.
The presence of solvents exceeding
trace levels should not be present in
soiling (especially those in hazard class
A1).
To avoid any corrosion damage,
ensure that solutions or steam
containing hydrochloric acid do not
come into contact with the steel outer
casing of the machine.
Please follow the advice on
installation in these instructions
and the separate Installation
Instructions.
Warning and Safety instructions
Using accessories
Only use genuine Miele
accessories with this machine.
Consult Miele on the type and
application of such equipment.
Disposal of your old machine
Before disposing of your old
machine first make it unusable.
Disconnect from the mains, cut off the
cable near the machine and any plug
from the cable.
For environmental and safety reasons
ensure the machine is completely
drained of any residual water and
cleaning agent. (Observe safety
regulations and wear safety goggles
and gloves).
Make the door lock inoperative, so that
children cannot accidentally shut
themselves in. Then make appropriate
arrangements for the safe disposal of
the machine.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
9
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
or machine
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Electrical and electronic appliances /
machines often contain materials
which, if handled or disposed of
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Please do
not therefore dispose of your old
machine or appliance with your
household waste.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Rather than just throwing these
materials away, please ensure that they
are recycled.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person. The plug must be
rendered useless and the cable cut off
directly behind it to prevent misuse.
See the "Warning and Safety" section of
this booklet for further details.
10
Before using for the first time
Load the machine carefully
Before using for the first time please
pay special attention to the following
points.
Detailed information on these points
can be found in the relevant sections of
these Operating Instructions.
Set the water softener unit
The water softener unit must be set for
the water hardness level in your area.
The salt reservoir also has to be filled,
first with water and then with
reactivation salt.
,Filling the salt reservoir with
cleaning agent by mistake will cause
serious damage to the water
softener. Please check every time
before refilling that the package
contains reactivation salt.
Arrange the load so that water will
come into contact with all surfaces.
Concealed surfaces will not be
cleaned.
The spray arms must not be blocked by
any items.
Add cleaning agent
Follow the cleaning agent
manufacturer’s recommendations on
dosage.
The amount required will depend on the
type of cleaning agent and the
programme chosen.
Make sure you read the notes on
dosing given in the programme chart.
Cleaning results may vary from brand
to brand. If you are not satisfied with
the results from one brand, try another
quality brand before contacting Miele
for advice.
Add rinsing agent
,Inadvertently filling the reservoir
for rinsing agent with cleaning agent
(including liquid cleaning agents
and washing up liquid) will cause
serious damage to the reservoir.
The filter combination at the base of
the wash cabinet and the spray arms
must be kept clean.
Regular checking and cleaning is
essential.
Only use designated cleaning agents
for special applications.
Do not use cleaning agents formulated
for use in domestic dishwashers.
11
Opening and closing the door
Open the door a
To close the door
^ Press the door button in as far as it
will go, and at the same time, grip the
handle and open the door.
^ Lift the door upwards and push until
it clicks shut. Do not press the door
release button whilst shutting the
door.
The door should only be opened during
operation for emergencies, e.g. if
articles are knocking together or if a
programme fault is indicated in the
display (see "Cancelling a
programme").
,Do not touch the heating
elements if you open the door during
or directly after the end of a
programme: you could burn
yourself. The elements remain hot for
some time after the end of the
programme.
12
Water softener
The water needs to be softened to
avoid calcium deposits building up on
utensils and in the machine itself.
To ensure a steady supply of soft water,
the water softener unit must always be:
For future servicing it is useful to make
a note of your water hardness level.
^ Enter your water hardness level here:
°d / mmol/l
1. correctly programmed and
2. the salt reservoir must be filled.
If the water hardness level is below 4
°d - German scale (0.7 mmol/l), the
reservoir does not need to be filled
with reactivation salt.
The machine is set at the factory for a
water hardness level of 19 °d (3.4
mmol/l).
If the water supply is harder or softer
than this (including below 4 °d or 0.7
mmol/l), the factory setting will need
to be changed following the
instructions in Setting the water
softener. See chart on the next page
for settings.
Your local water authority will advise
you on the water hardness in your area.
For fluctuating levels e.g. 8 - 17 °d (1.4
- 3.1 mmol/l) set the water softener to
the highest setting. In this example to
17 °d (3.1 mmol/l).
Important
The built-in water softener has settings
from 1 °d - 60 °d (0.2 - 10.8 mmol/l).
13
Water softener
Table of settings
°d
(German
scale)
mmol/l
°f
Setting
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
0.2
0.4
0.5
0.7
0.9
1.1
1.3
1.4
1.6
1.8
2.0
2.2
2.3
2.5
2.7
2.9
3.1
3.2
3.4
3.6
3.8
4.0
4.1
4.3
4.5
4.7
4.9
5.0
5.2
5.4
5.6
5.8
5.9
6.1
6.3
6.5
6.7
6.8
7.0
7.2
7.4
7.6
7.7
7.9
8.1
2
4
5
7
9
11
13
14
16
18
20
22
23
25
27
29
31
32
34
36
38
40
41
43
45
47
49
50
52
54
56
58
59
61
63
65
67
68
70
72
74
76
77
79
81
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19 *)
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36 **)
37
38
39
40
41
42
43
44
45
14
°d /
mmol/l
mmol/l
°f
Setting
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
8.3
8.5
8.6
8.8
9.0
9.2
9.4
9.5
9.7
9.9
10.1
10.3
10.4
10.6
10.8
83
85
86
88
90
92
94
95
97
99
101
103
104
106
108
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
*) factory setting
**) 1-36 only for U.K.
Machines without a water softener
are set to 0 at the factory. This
setting of 0 must not be changed on
these machines.
Water softener
Setting the water softener
^ Switch the machine off.
^ Turn the programme selector to the
STOP position f.
^ Press 4 and 6 at the same time,
hold them in and, whilst doing so,
switch the machine on with the I-0
button.
The current programme status "P..."
will show in the display.
The indicator light p / 6 will come
on.
^ Press 3 once. E01 for programming
level 1 will appear in the display.
^ Turn the programme selector six
switch positions clockwise (6 o’clock
position).
The number 19 will appear in the
display (the factory water hardness
setting in °d, equivalent to 3.4
mmol/l).
^ Press 4 as many times as is
necessary, or hold it in until the
required value (hardness level in °d)
appears in the display.
Once the number 60 (36 only for
U.K.) has been reached, the counter
will begin again at 0.
^ Press the 6 button. SP appears.
^ Press 6 again. The setting will now
be stored in the memory. The display
clears.
^ The machine is now ready for
operation.
15
Water softener
Filling the salt reservoir
Please only use special coarse grained
reactivation salt with granules of
approx. 1-4 mm. Do not use other types
of salt, e.g. table salt, agricultural or
gritting salt. These could contain
components which are insoluble in water which could result in damage to the
water softener. If in doubt consult your
Miele Professional Department.
Before filling the salt reservoir with
reactivation salt for the first time, fill it
with approx. 2.5 litres of water.
The salt reservoir holds approx. 2.5 kg
of salt.
,Inadvertently filling the salt
reservoir with cleaning agent will
damage the water softener.
Before filling the salt reservoir make
sure that you have picked up the
right packet of reactivation salt.
^ Remove the bottom basket from the
machine.
^ Unscrew the salt reservoir cap.
^ Place the funnel provided in place.
^ Fill carefully with salt. As it is filled,
displaced water will run out).
^ Wipe any residual salt off the screw
threads on the socket.
^ Screw the cap on firmly.
^ Immediately after this: Run the
PRE-RINSE programme D to remove
any traces of salt from the cabinet.
Important: If after starting the
PRE-RINSE programme D the machine
does not start for a few minutes this is
not a fault. The water softener is being
reactivated.
16
Water softener
Salt indicator
When the salt reservoir is empty the k
indicator light b comes on to remind
you to fill the reservoir.
Reactivation takes place automatically
during a programme.
The programme sequence indicator
light k a lights up whilst this is
happening.
17
Loading the machine
Loading the machine
Preparing the load
^ Empty all containers before loading
into the machine.
,Ensure that no acid or solvent
residues, especially hydrochloric
acid or chlorides, get into the wash
cabinet.
Please note
^ Load items so that water will come
into contact with all surfaces. This
ensures that they will be properly
cleaned.
^ Do not place items to be cleaned
inside other pieces where they may
be concealed.
^ Hollow vessels such as cups,
glasses, pots etc. should be inverted
and placed in the correct inserts. The
water must be able to access them
unhindered.
^ Deep-sided items should be placed
at an angle so that water can run off
them unhindered.
^ Tall, narrow, hollow items should be
placed in the centre of the baskets to
ensure better water coverage.
^ Small pieces should be placed on
the cup racks in the upper basket.
Do not obscure them by larger items
below. Cups should be on the lower
rack and bowls on the top rack so
that water reaches all items.
18
^ The water duct for the spray arm in
the middle of the upper basket must
not be obstructed.
^ The spray arms must not be blocked
by items which are too tall or which
hang down in their path. If necessary,
manually rotate the arms to test.
Use the upper basket for:
^ Small lightweight, delicate items such
as cups, saucers, glasses, dessert
bowls etc., as well as for lightweight
thermally stable plastic items.
Use the bottom basket for:
^ Larger and heavier items such as
plates, serving platters, saucepans,
bowls etc. Glasses may only be
cleaned in the bottom basket if it is
fitted with a special glassware insert
or if there is a special bottom basket.
Cutlery
^ Unsorted cutlery should be placed in
the cutlery holders with the handles
facing downwards.
However, to avoid the risk of injury,
sharp kinves etc. should be placed
with the pointed end facing
downwards.
Select baskets and inserts which are
appropriate for the application.
See examples on the following
pages.
Loading the machine
Loading examples:
Individual top and bottom baskets
O 881 Top basket
for 20 cups, 24 saucers or 12 dessert
plates.
O 889 Top basket carrier
to take various inserts, e.g. containers
for cutlery and glasses.
U 880 Bottom basket
with 2 x E 216 half inserts each for 15
plates Ø 240 mm and 2 x E 165 cutlery
baskets for mixed cutlery.
U 880 Bottom basket
with E 884 insert 1/1 for 20 large plates
or 10 trays.
19
Loading the machine
Glass set GG/F-GL
O 882 Top basket
for 27 glasses Ø 65 mm.
U 880 Bottom basket
with 2 x E 205 half inserts each for 14
glasses Ø 65 mm.
20
Loading the machine
Adjusting the top basket
The top basket can be adjusted above
and below the middle position by 2.5
cm. It is set in the middle position on
delivery.
Items not suitable for
dishwashers
^ Cutlery with wooden or horn handles.
^ Wooden or plastic cutting boards.
Depending on the position of the top
basket, plates of the following diameter
can be accommodated in the baskets:
^ Glued items, e.g. old knives with
handles which have been glued on.
Example: Top basket O 881
^ Copper or tin items.
Top basket
position
Top basket
plate Ø in
cm
Bottom
basket
plate Ø in
cm
Top
max. 16.5
24 *)
Middle
max. 19
24 *)
Bottom
max. 21.5
24 *)
*) in insert E 216. For plates up to
Ø 30 cm, use insert E 888.
To adjust the top basket:
^ Pull out the top basket until a
resistance is felt; lift from the runners
and remove.
^ Hand-made craft items.
^ Plastic items which are not heat
resistant.
Please note
^ Silver and aluminium items can suffer
some discolouration.
^ Colours painted over a glaze may
fade after a number of washes.
^ Clouding may occur on glasses after
frequent washing.
Our recommendations
^ Wash delicate glassware by hand.
^ When purchasing new glasses,
dishes and cutlery make sure they
are dishwasher safe.
^ Unscrew the knurled nuts (roller
bearings) on both sides of the basket
with a suitable spanner and
reposition as required.
21
Adding rinsing agent
Rinsing agent is necessary to ensure
water does not cling and leave marks
on items during the drying phase and
to help items dry faster after they have
been washed.
Rinsing agent is poured into the
storage reservoir and the amount set is
dispensed automatically in the final
rinse.
The rinsing agent reservoir holds
approx. 125 ml.
Except: Rinsing agent is not dispensed
in the final rinse in the BEER GLASS
programme. The final rinse in this
programme is carried out with cold water only.
,Inadvertently filling the rinsing
agent reservoir with powder or liquid
cleaning agent will always cause
serious to damage the reservoir.
Make sure you use a rinsing agent
which is suitable for use in this
machine.
Adding rinsing agent
If the H Add rinsing agent indicator
light on the control panel comes on, the
rinsing agent reservoir must be refilled.
^ Open the door fully.
^ Press the button in the direction of
the arrow until the flap springs open.
22
Adding rinsing agent
^ Add rinsing agent only until it is
visible on the surface of the filter in
the opening.
^ Close the flap firmly. The flap must
audibly engage, otherwise water
could get into the rinsing agent
reservoir during the programme.
^ Mop up any spilt rinsing agent. This
prevents over-foaming occuring
during the next programme.
The flap should always remain closed.
Only open it to add more rinsing agent.
^ Wait until the H indicator light on the
control panel lights up again before
adding any more rinsing agent.
23
Adding rinsing agent
Setting the dosage
The dosage adjuster in the opening has
settings from 1 to 6 (1-6 ml). It is set to
3 (3 ml) at the factory as the
recommended dosage for rinsing
agent.
^ Use a higher setting if there are
marks on the surface of utensils after
drying.
^ Use a lower setting if the surface
becomes cloudy and smeary.
24
Adding cleaning agent
,Only use cleaning agents
suitable for specialist machines. Do
not use detergents formulated for
domestic dishwashers.
Powder cleaning agent is dispensed
via the dispenser for powder cleaning
agents in the door or liquid cleaning
agent via the DOS module (available as
an optional extra - see "Note" on the
next page).
If liquid cleaning agent is not being
used, powder cleaning agent must be
placed in the cleaning agent dispenser
before every programme except with
PRE-RINSE D (see notes on detergent
dispensing in the programme chart).
^ Add powder cleaning agent to
compartment II.
Dosage: Approx. 3 g/l, or 20 g per
wash cycle.
Approx. 7 litres of water are used in the
main wash.
Follow cleaning agent manufacturer’s
instructions if they differ.
^ Close the dispenser lid.
Some types of soiling may require
different combinations of cleaning
agents and other additives. The Miele
Professional Department will be
pleased to advise you.
^ Press the opening catch on the
container forwards (see arrow). The
flap will spring open. (The flap is
always open at the end of a
programme).
25
Adding cleaning agent
Note
As a chargeable optional extra, this
machine can also be fitted with a DOS
Module G 60 dispenser pump for liquid
cleaning agent. This is connected
externally.
See Programming special functions for
venting the dispensing system and
setting the dosage.
The optional DOS Module is supplied
with its own installation and connection
instructions.
Maintenance of the dispensing
system
To ensure trouble-free operation,
regular maintenance should be carried
out at specified intervals by a Miele
approved service technician.
Every two years
Replace the dispensing hoses in the
DOS modules.
26
,Take great care when handling
liquid agents and additives. These
may contain irritant or corrosive
ingredients.
Please follow the manufacturer’s
safety instructions.
Wear protective gloves and goggles.
Programme selection
Choose your programme according to
the type of instruments or utensils being
cleaned, and the degree of soiling.
The different programmes and their
uses are described overleaf in the
Programme Chart.
27
Programme chart
Programme
When to use
Powder cleaning agent
(when not using liquid
cleaning agent)
Follow manufacturer’s
instructions
D
PRE-RINSE
To rinse heavily soiled items, (e.g. for removing
soiling or to prevent soiling drying on to dishes
when a complete programme does not yet need
to be run).
,
BEER
GLASSES
Special programme for beer glasses.
(Instead of being left to dry in the machine, beer
glasses are taken out and dried by hand).
20 g in the powder
dispenser
o
GLASSWARE
Special programme for glasses.
20 g in the powder
dispenser
s
SHORT
Quick programme for lightly soiled crockery.
20 g in the powder
dispenser
G
UNIVERSAL
For normally soiled loads.
20 g in the powder
dispenser
n
UNIVERSAL
PLUS
For normally soiled items with a higher wash
temperature for removing foods rich in starch
20 g in the powder
dispenser
F
INTENSIVE
For heavily soiled crockery. Most of the soiling is
removed in an intensive cold-water pre-rinse.
20 g in the powder
dispenser
6
DRAIN
For draining water out of the machine, e.g. when
a programme has been interrupted. Turn the
programme selector to the STOP position f first.
28
Programme sequence
1.
Economy
pre-wash
2.
Pre-wash
3.
Main wash
4.
Economy
interim
rinse
5.
Interim
rinse I
6.
Interim
rinse II 2)
7.
Final
rinse
8.
Drying
(Additional
prog.)
(X)
X
—/1’
(X)
X
X
50°C/1’
X
1)
X
50°C/1’
3)
X
(X)
1)
X
(X)
1)
X
55°C/2’
X
60°C/3’
X
(X)
X
X
65°C/3’
1)
(X)
X
60°C/1’
(X)
1)
X
(X)
1)
X
X
60°C/1’
1)
1)
X
(X)
1)
X
55°C/1’
X
X
50°C/1’
X
60°C/1’
(X)
1)
X
(X)
X
60°C/1’
(X)
1)
X = Sections included in a programme (with temperature/temperature holding time)
1)
To change a temperature or temperature holding time, see Programming special functions.
Important: We recommend programming a main wash temperature of 60°C for cleaning dirty
crockery.
2)
To select a second interim rinse see Programming special functions.
3)
With cold water and without rinsing agent.
29
Operation
Switching on
^ Close the door.
^ Open the stopcocks (if turned off) .
^ Press the I-0 button.
When the programme selector is at the
STOP position f a point lights up in the
display.
Starting a programme
^ Turn the programme selector
clockwise or anti-clockwise to the
required programme.
The temperature of the programme
selected is shown in the display,
except with PRE-RINSE D and
DRAIN 6.
The indicator light next to the START
button 6 flashes.
^ Select additional function DRYING
3 if required (see "Selecting an
additional function").
^ Press the START button 6. The
duration of the programme selected
will appear in the display, counting
upwards in minutes.
The indicator light next to the START
button lights up.
30
Once the programme has started, all
other programmes are blocked. If the
programme selector is then turned to
another programme, the values shown
in the display go out. The values can be
seen again if the programme selector is
turned back to the position of the
programme currently in operation.
^ Press the 4 button to alternate
between showing the current
temperature and the amount of time
elapsed in the display.
Note that during the heat-up stage in
"Main wash" and "Final rinse" the
required end temperature is shown in
the "time run" display.
Operation
Changing a programme
Programme end
Provided the START button has not yet
been pressed, a wrongly selected
programme may be changed as
described below (if it has been
pressed, see Cancelling a programme):
The programme has ended when no
more programme sequence indicator
lights are lit up and the "Start" indicator
light 6 has gone out. A 0 will appear in
the middle of the display.
The buzzer will sound at the same time
for a max. of 30 seconds (standard
setting). The buzzer can be changed
(see "Programming special functions").
^ Turn the programme selector to the
required programme.
^ Select additional function DRYING
3 again if required (see Selecting
an additional function).
^ Press the START button 6.
Use the 4 button to see the total
running time of a programme or the
actual temperature.
Selecting an additional function
Switching off
The following additional function can be
selected:
^ Press and release the I-0 button.
^ 3 DRYING
Drying may be selected as an
additional function as soon as the
programme has been selected
(except with PRE-RINSE D and
DRAIN 6). The drying phase
operates with pulsed heating for ten
minutes. The total running time of the
programme lengthens accordingly.
Programme sequence indicators
The indicator light for the active
programme stage lights up during the
programme.
k
Reactivation
I
Pre-wash
l
Main wash
m / H Interim rinse/Final rinse
c
Drying (additional function)
31
Operation
To cancel a programme
Once a programme is running it should
only be cancelled in extreme cases,
e.g. when articles in the machine rattle
or jostle against each other and have to
be rearranged.
^ Turn the programme selector to the
f position (the programme is
cancelled after approx. 2 secs.).
^ Open the door a
,Caution - Water and items in the
machine may be hot. Danger of
burning or scalding.
^ Arrange the load securely.
(Wear protective gloves where
necessary, and observe appropriate
health and safety regulations relating
to infectious diseases).
^ Replenish powder cleaning agent if
necessary.
^ Close the door.
^ Select the DRAIN programme 6 (water in the machine is pumped away).
^ Select the cleaning programme again
and start it as previously described.
32
Programming special functions
For future servicing work, please
document any alterations to the standard factory settings.
Enter any alterations in the relevant
Value set:_________ box.
.
1. Setting the cold water inlet from:
Nominal water intake to Nominal water intake + 1 l.
The amount of water taken into the
machine at each intake can be
increased by 1 litre to a maximum of
9.5 litres.
To do this:
^ Turn the programme selector to STOP
f.
^ Switch the machine off.
^ Press and hold 4 and 6 at the
same time, and whilst doing so
switch the machine on with the I-0
button.
The current programme status “P...”
appears in the display and the p / 6
indicator lights up.
^ Press 3 once. E01 for programming
level 1 will appear in the display.
^ Turn the programme selector to the
D position. A 10 or an 11 will appear
in the display.
10 = Nominal water intake
11 = Nominal water intake + 1 l
Value set:
2. Selecting a second interim rinse
Interim Rinse II can be programmed in
to improve interim rinsing in all
programmes (except D PRE-RINSE).
^ Turn the programme selector to STOP
f.
^ Switch the machine off.
^ Press and hold 4 and 6 at the
same time, and whilst doing so
switch the machine on with the I-0
button.
The current programme status “P...”
appears in the display and the p / 6
indicator lights up.
^ Press 3 once. E01 for programming
level 1 will appear in the display.
^ Turn the programme selector to o. A
30 or an 31 will appear in the display.
30 = without Interim rinse II.
31 = with Interim rinse II.
^ Press 4 to change from 30 to 31 or
vice versa.
^ Press 6. SP appears.
^ Press 6 again. The change has
been recorded.
Value set:
^ Press 4 to change from 10 to 11 or
vice versa.
^ Press 6. SP appears.
^ Press 6 again. The change has
been recorded.
33
Programming special functions
3. Delay start and setting the delay
start time
The start of a wash programme can be
delayed by up to 9 hours and 30
minutes in 30 minute stages.
Note:
Delay start should only be selected with
the Universal and Intensive
programmes. Because items in the
machine stand for a longer period
before being cleaned, residues can dry
on if the start time is delayed. Shorter
programmes may not be able to
remove dried on soiling adequately.
a) To activate Delay Start
^ Turn the programme selector to STOP
f.
^ Switch the machine off.
^ Press and hold 4 and 6 at the
same time, and whilst doing so
switch the machine on with the I-0
button.
The current programme status “P...”
appears in the display and the p / 6
indicator lights up.
^ Press 3 once. E01 for programming
level 1 will appear in the display.
^ Turn the programme selector to 6.
80 or 81 will appear in the display.
80 = No delay start
81 = Delay start active.
^ Press 4 to change from 80 to 81 or
vice versa.
^ Press 6. SP appears.
^ Press 6 again. The change has
been recorded.
34
Value set:
b) Setting the delay start period
The delay start period (from 30 minutes
to 9 hours and 30 minutes) has to be
set before a programme is started.
^ After selecting a programme (see
“Switching on”) Press the 4 button
or hold it in until the required value is
displayed. The “Delay Start” indicator
light comes on.
After the START button 6 has been
pressed the delay start period will
count down in the display until the
programme automatically starts.
Programming special functions
4. Venting and setting the dosage on
DOS modules G 60 and C 60
(optional extra)
^ Set the dosage selector on the DOS
module to position 10 (applies to
DOS Module C 60 only).
^ Turn the programme selector to STOP
f.
^ Switch the machine off.
^ Press and hold 4 and 6 at the
same time, and whilst doing so
switch the machine on with the I-0
button.
The current programme status “P...”
appears in the display and the p / 6
indicator lights up.
^ Press 3 twice, E02 for programming
level 2 will appear in the display.
Venting the dispensing system:
^ Turn the programme selector to the
D position. do1 appears in the
display.
^ Press 4 for 90 seconds.
The dispensing system will be vented
automatically.
If only venting is required:
Setting the dosage:
Set the dosage according to the
manufacturer’s recommendations.
The machine needs 7 litres of water in
the main wash stage of the programme.
Example:
A manufacturer recommends 4 ml
cleaning agent per litre of water:
7 l x 4 ml/l = 28 ml.
2 ml . 1 second dispensing time; i.e.
programming to 14 seconds.
^ Turn the programme selector to ,, the
dispensing time in seconds appears
in the display, e.g 10.
^ Press 4 repeatedly or hold it in, until
the number 14 appears in the display
(dispensing time 14 seconds . 28 ml
- see example - ).
The dispensing time/amount is set.
^ Having changed a value or all
values:
^ Press 6. SP appears.
^ Press 6 again. The change has
been recorded.
Value set:
^ Switch the machine off with the I-0
button.
If the dispensing system also needs to
be vented:
Immediately after this: start the
PRE-RINSE D programme, so that after
venting any agents in the wash cabinet
are diluted before being drained away.
^ Start the PRE-RINSE programmeD,
so that after venting any agents in the
wash cabinet are diluted before
being drained away.
35
Programming special functions
5. Altering the temperature and/or the
temperature holding time in the
“Main wash” and “Final rinse”
programme stages
Please make a note of any changes
to the temperature and / or the
temperature holding time in the
appropriate section of the
programme chart.
The programme chart shows the factory
settings for the Main wash temperature
together with temperature holding time
and the Final rinse temperature with its
temperature holding time.
The special functions can be used to
alter the temperatures of the main wash
and of the final rinse from 30 °C -70 °C
and the temperature holding time from
1-10 minutes.
Important: We recommend
programming a main wash temperature
of 60°C for cleaning dirty crockery.
The final rinse temperature cannot be
programmed or altered in the , BEER
GLASSES programme.
^ Turn the programme selector to the
STOP position f (the programming
level is displayed only in this switch
position).
^ Switch the machine off.
^ Press and hold 4 and 6 at the
same time, and whilst doing so
switch the machine on with the I-0
button.
The current programme status “P...”
appears in the display and the p / 6
indicator lights up.
36
^ "Main wash" temperature:
Press 3 three times, E03 for
programming level 3 will appear in
the display.
^ Turn the programme selector to the
programme which needs to be
changed. The actual value appears
in the display after °C.
^ Press 4 or hold it in, until the
required value appears in the display.
^ "Main wash" temperature holding
time:
Turn the programme selector to the
STOP position f
(the programming level is only
displayed in this switch position).
^ Press 3 again, E04 for
programming level 4 will appear in
the display. Then:
^ Turn the programme selector back to
the programme which needs to be
changed. The actual value appears
in the display after min.
^ Press 4 until the required value
appears in the display.
^ "Final rinse temperature:
Turn the programme selector to the
STOP position f
(the programming level is only
displayed in this switch position).
^ Press 3 again, E05 for
programming level 5 will appear in
the display. Then:
Programming special functions
^ Turn the programme selector back to
the programme which needs to be
changed. The actual value appears
in the display after °C.
^ Press 4 or hold it in, until the
required value appears in the display.
^ Final rinse temperature holding
time:
Turn the programme selector to the
STOP position f
(the programming level is only
displayed in this switch position).
^ Press 3 again, E06 for
programming level 6 will appear in
the display. Then:
^ Turn the programme selector back to
the programme which needs to be
changed. The actual value appears
in the display after min.
^ Press 4 until the required value
appears in the display.
^ Having changed a value or all
values:
^ Press 6. SP appears.
^ Press 6 again. The change has
been recorded.
37
Programming special functions
6. Audible tone (Buzzer)
This special function allows you to
programme a buzzer (lasting up to a
maximum of 30 seconds) for the
following functions:
– Programme end = Constant buzzer
– Fault warning = Buzzer at one
second intervals
^ Turn the programme selector to STOP
f.
^ Switch the machine off.
^ Press and hold 4 and 6 at the
same time, and whilst doing so
switch the machine on with the I-0
button.
The current programme status “P...”
appears in the display and the p / 6
indicator lights up.
^ Press 3 once. E01 for programming
level 1 will appear in the display.
^ Turn the programme selector nine
switch positions clockwise (9 o’clock
position).
A number from 90 to 93 will appear in
the display.
90 = buzzer switched off.
91 = buzzer at end of programme
(standard setting)
92 = fault indication
93 = buzzer for all functions (at end
of programme and for faults).
^ Press 4 until the required function is
displayed.
^ Press 6. SP appears.
38
^ Press 6 again. The change has
been recorded.
Value set:
Note:
The buzzer can be switched off early
by
– turning the programme selector to
the STOP position f,
– interrupting the power supply (e.g.
by opening and closing the door).
Programming special functions
7. Re-setting all parameter changes
back to the factory settings.
^ Turn the programme selector to STOP
f.
^ Switch the machine off.
^ Press and hold 4 and 6 at the
same time, and whilst doing so
switch the machine on with the I-0
button.
The current programme status “P...”
appears in the display and the p / 6
indicator lights up.
^ Press 3 seven times, E07 for
programming level 7 will appear in
the display.
^ Turn the programme selector to any
switch position (except STOP).
00 or PP will appear in the display.
00 = factory setting
(Electronics have not been
re-programmed).
PP = Electronics have been
re-programmed.
^ If PP is displayed press 4 to
change from PP to 00.
^ Press 6. SP appears.
^ Press 6 again. All values which had
been changed have now been now
reset to the factory settings.
If the hardness level setting in the water
softener had been changed this will
reset to the factory setting of 19 °d (3.4
mmol/l). This will need to be reset to
suit the hardness level in your area.
39
Cleaning and care
Cleaning the filters in the wash
cabinet
,The machine must not be used
without all the filters in place.
The filter combination in the base of
the wash cabinet should be
inspected regularly and cleaned if
necessary.
,Caution:
Watch out for glass splinters which
could cause injury.
Cleaning the coarse filter
^ To unscrew the micro-fine filter, take
hold of the two lugs and turn twice in
an anti-clockwise direction,
^ Press the two lugs together, remove
and clean the filter.
^ and remove, together with the flat
filter.
^ Put the clean filter back in position
and press it until it clicks into place.
^ Clean the filters.
Cleaning the flat and the micro-fine
filters
^ Remove the coarse filter.
40
^ The filter combination is then
replaced in the reverse order in
which it was removed.
Cleaning and care
Cleaning the spray arms
Waste particles can lodge in the spray
arm jets.
The spray arms should be inspected
and cleaned regularly (approx. every
6 months).
^ Use a sharp pointed object to push
particles into the spray arm jets and
rinse well under running water.
Remove the spray arms as follows:
^ Unscrew the upper spray arm.
^ Remove the middle spray arm (on
the top basket) by unscrewing the
toothed wheel mechanism.
Important:
The toothed wheel mechanism has a
left hand thread, and to unscrew it, it
must be turned to the right with the
spray arm.
Particles in the lower spray arm are
easier to rinse out if the cap is first
opened.
^ Open the cap in the direction of the
arrow. After cleaning close up the
cap again.
Important:
After replacing the spray arms check
that they move freely.
^ First remove the bottom basket and
then pull the lower spray arm off.
41
Cleaning and care
Cleaning the drain pump and
non-return valve
The drain pump is situated under the
non-return valve (see arrow).
If water has not been pumped away at
the end of a programme the drain
pump or the non-return valve might be
blocked. They are however, easy to
clean.
^ Take the filter combination out of the
wash cabinet.
^ Before replacing the non-return valve
check that the drain pump is free of
obstructions.
^ Carefully replace the non-return valve
and secure with the locking clamp.
^ Release the locking clamp.
^ Lift up the non-return valve and rinse
under running water.
42
Cleaning and care
Cleaning the filters in the water
inlet
^ Replace filters and the seal. Make
sure they are sitting correctly.
Filters are incorporated in the screw
connection of the water inlet hose to
protect the water inlet valve. If these
filters get dirty they need to be cleaned,
otherwise insufficient water flows into
the wash cabinet.
^ Reconnect the hose to the water inlet,
making sure that it goes back on
straight.
,The plastic housing of the water
connection contains an electrical
component. It must not be dipped in
water.
To clean the filters
^ Disconnect the machine from the
mains supply (switch off at the mains
and pull out the plug, switch off the
appropriate circuit in the fuse box or
withdraw the mains fuse).
^ Turn off the stopcock and unscrew
the water inlet hose.
^ Open the stopcock carefully.
If there is a leak, screw the
connections on more tightly.
Cleaning the control panel
^ This should only be cleaned with a
damp cloth or a suitable cleaner for
use on plastic materials, or with a
disinfectant tested and recognised
as suitable for this use.
,Do not use abrasive cleaners,
glass cleaners or all-purpose
cleaners.
Because of their chemical
composition they could cause
serious damage to plastic
components.
Cleaning the front of the
machine
^ Clean using a proprietary cleaning
agent designed for the type of front
the machine is fitted with.
,Do not use cleaning agents
containing ammonia or thinners.
^ Clean the large area filter (1) and fine
filter (2), and replace with new filters
if necessary.
43
Correcting minor faults
With the aid of the following explanatory
notes, minor faults can be corrected
without contacting the Miele Service
Dept.
The wash cycle finishes too early and
the p / 6 indicator light flashes
(fault code F A appears in the
display)
Any work on the electrical components
of the machine should only be carried
out by a suitably qualified and
competent person in accordance with
local and national safety regulations.
Unauthorised repairs could be
dangerous.
– The drain hose is kinked.
Faults / possible causes
The machine does not start
– The door is not properly closed.
– The machine is not switched on at
the mains.
– The fuse is defective / has blown.
A few minutes after switching on, the
p / 6 indicator light flashes (fault
code F..E appears in the display)
– The stopcocks are closed.
– The filters in the water inlet hose are
dirty.
– The water pressure is too low.
^ Turn the programme selector to the
STOP position f (the fault code
goes out).
^ Press I-0 to switch the machine off.
^ Open the stopcocks or clean the
filters (see "Cleaning and Care").
^ Switch the machine on again and
reselect the programme.
44
– The drain pump is blocked
^ Turn the programme selector to the
STOP position f (the fault code goes
out).
^ Straighten the hose and check/clean
the drain pump.
^ Pump away the water and start the
programme again (see additional
programme "DRAIN" and "Switching
on").
Correcting minor faults
Water in the wash cabinet is not
heated; the programme sequence
lasts too long
This machine has a resettable heater
limiter which will switch off the heaters if
they over-heat. This could be caused
for example, by large articles covering
the heating elements or if the filters in
the wash cabinet are blocked.
Customer service
Should you still have any difficulties or if
a fault code "F..." appears in the display
again, please contact your authorised
Service Dealer or the Miele Service
Department. See back cover for
addresses. Please quote the fault code
as well as the model type and number
of your machine.
^ Remove the cause of the fault.
^ Take off the service panel (see
"Electrical connection").
^ Press the reset button on the heater
limiter (yellow) located on the lefthand side of the plastic cover.
If this switch trips again contact the
Miele Service Department.
45
Installation
Please refer to the installation
diagram supplied with the machine.
^ Open the door.
,Furniture and fittings installed
near the machine must be of a
commercial standard able to
withstand the effects of steam and
condensation.
The machine must be installed correctly
and levelled.
Any unevenness in the floor level can
be compensated for and the height of
the machine raised or lowered by
adjusting the four screw feet.
The machine can be installed in the
following ways:
^ Free-standing.
^ Slot-in or at the end of a row:
The machine can be installed next to
other machines or furniture or in a
suitable niche. The niche must be at
least 60 cm wide and 60 cm deep.
^ Built-under:
The machine can be installed under a
continuous worktop or sink drainer.
The recess must be at least 60 cm
wide, 60 cm deep and 82 cm high.
If necessary, the machine lid can be
removed as follows:
46
^ Remove the fixing screws on the left
and right hand sides using a cross
slotted screwdriver.
^ Pull the machine lid approx. 5 mm
forwards, lift it upwards and remove
it.
Installation
Position and secure the machine
To ensure stability the machine must
first be aligned and then screwed to the
worktop.
^ Open the door. Secure the machine
to the front edge of the worktop using
screws through the holes on the left
and right hand sides of the front trim.
^ Do not use silicone sealant to seal
the gaps between the machine and
any neighbouring units as this would
hinder ventilation to the circulation
pump.
Depending on the requirements for
building under, the following kits can be
ordered from the Miele Spares Dept.:
Cover plate (protects the worktop)
The underside of the worktop is
protected against water damage by a
stainless steel plate.
Decor frame fitting kit
The machine front can be fitted with a
decor panel to match kitchen units.
The decor frame is supplied with fitting
instructions.
47
Electrical connection
,All electrical work must be
Removing the plinth panel and the
protective plastic cover:
carried out by a suitably qualified
and competent person in
accordance with local and national
safety regulations.
^ Connection should be made via a
suitable isolator, with an on-off switch
which should be easily accessible for
servicing work.
WARNING
THIS APPLIANCE MUST BE
EARTHED
^ For extra safety it is advisable to
install a residual current device with a
trip current of 30 mA (in accordance
with DIN VDE 0664).
^ The mains connection cable may
only be replaced by an original Miele
spare part or an apppropriate cable
with wire end ferrule.
^ For technical data see data plate or
wiring diagram supplied.
The machine must only be operated
with the voltage, frequency and fusing
shown on the data plate.
This machine can be converted in
accordance with the conversion
diagram and wiring diagram supplied.
The data plate (with test certification
VDE, DVGW etc.) and conversion key
are located on the rear of the machine
and also behind the plinth panel below
the protective plastic cover.
The wiring diagram is secured to the
inner side of the protective plastic
cover.
48
,Disconnect the machine from the
mains electricity supply.
^ Holding the plinth panel at both
sides, pull gently outwards from
beneath a and pull it off b.
^ To remove the protective plastic
cover loosen the 2 screws (left and
right) c.
To re-assemble:
^ Refit the protective plastic cover and
the plinth panel in the reverse order
to which they were removed.
See also the installation diagram
supplied.
Bonding connection
There is a screw connection point
marked with the earth symbol (8) at
the back of the machine, to which the
earth lead must be connected.
Plumbing
Connection to the water inlet
,Water in the machine must not
be used as drinking water.
^ The machine must be connected to
the water supply in accordance with
local and national water authority
regulations.
^ This machine is constructed to
comply with German water
regulations (DVGW), and may be
connected to a suitable supply
without an extra non-return valve if
national regulations permit.
In the UK this machine is listed as a
WRAS approved product in the Water
Fittings and Materials Directory of
products which comply with the Water Fittings Regulations. It is
approved for mains water connection
in fluid categories 4 and 5, when
installed using the double check
valves supplied.
^ The water pressure (flow rate) must
be a minimum of 0.5 bar (50 kPa).
If the water pressure (flow rate) is
below 2 bar (200 kPa) the fill time is
automatically extended.
The max. permitted static pressure is
10 bar (1000 kPa).
If the water pressure is not in the
range of 0.5 to 10 bar (50-1000 kPa)
the p / 6 indicator light may come
on and the fault code "F2E" show in
the display. Please contact the Miele
Service Department.
^ The machine is supplied as standard
for connection to a cold or a hot water supply up to a max. temperature
of 70 °C.
^ A stopcock with 3/4 inch male thread
must be provided on site. It should
be easily accessible so that the water
supply can be turned off when the
machine is not in use.
^ The DN 10 inlet hose is approx. 1.7 m
long terminating in a 3/4 inch female
thread. A 1.5 metre long flexible
metal extension hose, pressure
tested to 140 bar, is available as an
optional accessory if required. On no
account may the inlet filter be
removed.
^ A large surface area filter is enclosed
in the kit supplied with the machine
for installing between the stopcock
and the inlet hose
(see illustration in "Cleaning and Care
- Water inlet").
,The inlet hose must not be
shortened or damaged in any way
(see illustration).
See also the installation diagram
supplied.
49
Plumbing
Drainage
^ The drainage system is fitted with a
non-return valve which prevents dirty
water from flowing back into the
machine via the drain hose.
^ The machine should preferably be
connected to a separate drainage
system on-site.
If separate drainage is not available
contact your Miele application
specialist for professional advice.
The on-site drain connection point
should be sited between 0.3 m and 1
m above the lower edge of the
machine.
If it is lower than 0.3 m lay the hose in
a curve at a height of at least 0.3 m.
The drainage system must be able to
take a minimum drainage flow of 16
l/min.
^ The inlet hose is approx. 1.4 m long,
is flexible and has an internal
diameter of 22 mm. It must not be
shortened.
Hose clips are supplied for securing
it in position.
^ A longer drain hose (up to 4 m long)
is available to order from the Miele
Spare Parts Dept.
^ The drainage system must not
exceed 4 metres.
See also the installation diagram
supplied.
50
Technical data
Height:
85 (82) cm
Width:
60 cm
Depth:
60 cm
Voltage:
Rated load:
Fuse rating:
see data plate
see data plate
see data plate
Mains connection cable:
approx. 1.8 m
Water pressure (flow rate):
0.5 - 10 bar (50 -1000 kPa)
Cold or hot water connection:
up to max. 70 °C
Delivery head:
min. 0.3 m, max. 1 m
Drainage length:
max. 4 m
Inlet hose
approx. 1.7 m
Drain hose:
approx. 1.4 m
Noise level in dB (A):
Sound level LpA
Test marks:
Free standing: <70
Built under: <70
VDE, interference suppression, DVGW,
!
51
Alteration rights reserved / 3105
M.-Nr. 05 234 481 / 02
Download PDF

advertising