Chrysler | MyGIG | Mygig Lockpick Air Instructions

Mygig Lockpick Air Instructions
VES A/V OUTPUT
INCLUDED
AUDIO
OUT
UNPLUG ORIGINAL RADIO
CONNECTORS THEN PLUG IN HERE
FACTORY CONNECTORS
AUDIO
OUT
INCLUDED
PLUG AND PLAY
NO OTHER CONNECTIONS ARE
NECESSARY
VIDEO
OUT
AFTERMARKET REAR CAM
POWER TO LOCKPICK RED W/BLACK WIRE
GROUND TO LOCKPICK BLACK WIRE
ADDITIONAL CAM POWER
USB PROGRAMMING
INPUT
USB FIRMWARE
UPDATE INPUT
REVERSE CAM POWER
OPTIONAL
CAMERA POWER
12V ACC OUTPUT
PLUG AND PLAY
HARNESS INPUT
12V CONSTANT
OPTIONAL CAMERA
POWER CONNECTIONS
WIFI ANTENNA
INPUT
AUX A/V INPUT
GROUND
A/V INPUTS
A/V OUTPUT
INCLUDED
2ND REAR CAM
A/V OUTPUT
FRONT CAM
AFTERMARKET 2nd REAR CAM
POWER TO LOCKPICK RED W/BLACK WIRE
GROUND TO LOCKPICK BLACK WIRE
LEFT CAM
REMOTE CONTROL RECEIVER
DIP SWITCH
OPTIONS
LEFT CAM
POWER TO LOCKPICK
ORANGE W/BLACK WIRE
RIGHT CAM
REMOTE
SENSOR INPUT
GROUND TO LOCKPICK BLACK WIRE
RIGHT CAM
POWER TO LOCKPICK ORANGE W/BLACK WIRE
GROUND TO LOCKPICK BLACK WIRE
TM
MYGIG LOCKPICK AIR
INSTALLATION OPTIONS
COPYRIGHT 2014 COASTAL ELECTRONIC TECHNOLOGIES, INC.
FRONT CAM
POWER TO LOCKPICK ORANGE W/BLACK WIRE
GROUND TO LOCKPICK BLACK WIRE
TM
MYGIG LOCKPICK AIR
STEERING WHEEL CONTROLS
SCROLL UP
MENU
CONTROLS ON BACK
OF STEERING WHEEL
VOLUME UP
TAP IN SAT TV MODE
TO TOGGLE WIFI
AIRPLAY MODES
SELECT
PRESS AND HOLD
TO ACTIVATE MENUS
VOLUME DOWN
MENU
SCROLL DOWN
COPYRIGHT COASTAL ELECTRONIC TECHNOLOGIES, INC. 2014
Coastal Electronic Technologies, Inc.
Chrysler/Dodge/Jeep
MYGIG LOCKPICK AIR
Installation and Operation Instructions
Thank you for your purchase of the Coastal Electronic Technologies, Inc. MYGIG LOCKPICK
AIR. The LOCKPICK AIR has many features and capabilities to unlock and allow full use of your
Chrysler/Dodge/Jeep MYGIG radio PLUS an enormous suite of multimedia functions including multicamera inputs A/V inputs, and built in WiFi capabilities for Connection and Streaming from Android
Smartphone and Tablets. Apple smartphones and tablets have some restrictions for video streaming, see
application notes at bottom of page.
This is only a partial list of included features:
• The ability to use your navigation system without restrictions including the ability to input
addresses, search points of interest, etc. while in motion.
• You can also enjoy full use and video viewing of your DVD player(s) and Rear Seat Entertainment
(VES) Aux input jacks (if equipped), while in motion if you desire.
• Automatic activation of the TV mode in your radio with custom “channels” to control and activate
Lockpick functions. (fully compatible with factory Sat TV rear entertainment systems without loss
of function}
• Automatically enables the camera function in your radio with connections for up to 5 cameras. (fully
compatible with vehicles already equipped with a factory rear camera)
• Automatic camera options for turn signal activation of side cameras, front camera while parking
and rear or 2nd rear camera while in reverse, plus manual activation of any camera at any time.
• Advanced touch screen and steering wheel button control of all functions
• Full function remote control for quick and easy operations
• WIFI connection for wireless Audio and Video Mirroring !!
• USB update ability built in to keep your Lockick current with changing software needs.
This manual will document in detail, the many functions of the LOCKPICK AIR and how to properly
set the programming switches to your desired operation. Installation diagrams are included to guide you in
various connection strategies. Please read this manual fully so that you can learn to take advantage of all of
the exciting features and capabilities of the MYGIG LOCKPICK AIR.
At this time, Coastal Electronic Technologies, Inc. would like to recommend that you have this
installation completed by a certified mechanic or someone familiar with automotive electronics. This
installation, while not time consuming, does require careful attention to detail and precise following
of installation instructions.
Coastal Electronic Technologies, Inc. accepts no responsibility due to the improper installation or
use of this product. Installation and / or use of this product implies and signifies user acceptance of
this term of use. Please adhere to all driving laws in your state.
Apple streaming note: Apple markets a device called Apple TV which permits wireless streaming video
from your smartphone to the Apple TV for viewing on your television set. Apple restricts some streaming so
that only Apple TV receivers can show video. The Lockpick Air will allow mirroring of your smartphone
including all phone displays such as map, internet, pictures, texts, games etc. Videos recorded on your
device will stream to the Lockpick however, videos downloaded on iTunes are blocked. Updated versions of
the Netflix App (5.0 and above) will not stream. If your device still has the older Netflix version (4.31 or
below) video streaming is still possible. YouTube video streaming is also restricted to Apple TV, but
YouTube Apps such as PlayTube restore this function seamlessly and are free to download on iTunes.
Android phones have no such restrictions and will connect and stream to the Lockpick Air all functions.
OK, let’s get started. On your LOCKPICK AIR control box are switch settings which allow you to program
your Lockpick for the vehicle and application where it will be installed. Default settings when shipped are 1,
2, down, 3, 4 and 5 up. These settings are for high speed radio and vehicle applications. If your system is
the low speed communication type, then adjust the switches as directed in the following diagram. Improper
switch settings will not damage anything however it could cause your radio to fail to turn on or conflict with
existing accessories.
COMMUNICATION
TYPE
**CHECK APPLICATION
GUIDE BELOW
Place switches 1 AND 2 UP if
your vehicle uses LOW SPEED
communications
Place switches 1 and 2 DOWN
if your vehicle uses HIGH
SPEED communications
(DEFAULT SETTING)
LOW SPEED APPLICATIONS
SWITCH 1,2 UP
2007 – 2013
CHRYSLER SEBRING
2007 – 2014
DODGE AVENGER
20082008-2010
CHRYSLER 300 AND 300C
20082008-10
DODGE DURANGO
20082008-12
CHRYSLER ASPEN
ASPEN
20082008-2010
DODGE CHARGER
20082008-12
DODGE DAKOTA
20082008-2010
JEEP GRAND CHEROKEE
20082008-2010
JEEP COMMANDER
20082008-2014
CHALLENGER
20092009-2014
PATRIOT/COMPASS
20112011-2012
CHRYSLER 200/CIRRUS
HIGH SPEED APPLICATIONS
SWITCH 1,2 DOWN
20082008-2014
CHRYSLER TOWN AND COUNTRY
20082008-2014
DODGE CARAVAN
2007 – 2012
DODGE NITRO
20082008-2014
JEEP LIBERTY
20072007-2014
JEEP WRANGLER
20092009-2010
JOURNEY
20092009-2012
DODGE RAM
20112011-2013
JEEP GRAND CHEROKEE
20102010-2012
CALIBER
20112011-2013
DURANGO
20082008-2013
ROUTAN
IDENTIFY YOUR VEHICLE FROM THE APPLICATION GUIDE ABOVE AND
PLACE SWITCH 1, 2 UP OR DOWN AS DIRECTED BEFORE PLUGGING IN THE LOCKPICK.
DO NOT CHANGE THE SPEED SETTINGS WHILE THE MODULE IS PLUGGED
INTO THE HARNESS AND VEHICLE.
The MYGIG LOCKPICK AIR is designed with a simple “T” harness connector, equipped with factory
male and female connectors for direct connection to your screen. Specific links with videos demonstrating
methods of gaining access to the rear of the standard MYGIG radio is available for viewing at various links
at: http://www.coastaletech.com/MYGIG.htm
Most installations are relatively simple with just a single panel surrounding the radio which must be pulled
free before exposing the radio. Remove 4 screws holding the radio to view the connectors on the rear of the
radio. Consult a professional installer if you require assistance plugging in your Lockpick.
1.
With access to the rear of the screen, unplug the matching GRAY connector and plug it into the
female connector of your LOCKPICK harness. Then plug the male connector of the LOCKPICK
harness into the earlier factory location. The connectors are keyed and cannot be plugged in to the wrong
location. Line up the connectors carefully and make sure that no pins are bent or misaligned before
pressing hard to make sure the connector is fully seated.
2.
Next, unplug the White connector from the rear of the radio and plug it into the female connector of
the Lockpick module. Then plug the male connector of the Lockpick harness into the earlier factory
location. Make sure the connector is fully lined up properly and fully seated. If your vehicle did not have
a connector in this location, make sure and plug the Lockpick white connector into the radio to insure
proper video operations.
PLUG GRAY CONNECTOR FROM
THE LOCKPICK AIR HARNESS INTO
LOCATION SHOWN
PLUG WHITE CONNECTOR FROM
THE LOCKPICK AIR HARNESS INTO
LOCATION SHOWN
3. The programming switch settings for your Lockpick were detailed earlier and should be configured
before plugging the controller into the harness. Check that switches 1 and 2 are configured properly
and plug the Lockpick module into the harness.
4. FACTORY REAR CAMERA NOTE: 2008-2009 (some 2010) vehicles with factory rear view
cameras are powered only while the vehicles is in Reverse. If you would like to enable full control and
viewing of your FACTORY REAR VIEW CAMERA while in DRIVE or other gears, the REVERSE
CAMERA POWER output wire on the Lockpick Air harness must be connected as the power source
for your camera. This 12V power output will turn on when the vehicle is placed in reverse and also
when selected by the user using the radio buttons.
If you choose not to connect the REVERSE CAMERA POWER wire provided by the Lockpick
harness to your factory rear camera, the rear camera view while backing up will continue working as
normal. However, because the rear camera will have no power in other gears, it cannot be activated
by the Lockpick and will display as a blank or flashing picture if activated manually while in Drive.
If your installation requires the use of the REVERSE CAMERA POWER Lockpick wire to
enable factory camera operation in all gears, it is simply a matter of running a wire to the factory
camera and connecting it in place of the original power wire. Remove any panels covering the rear
hatch in your vehicle. Then use a meter or indicator lamp to determine the reverse power connection
on the factory camera connector. Make sure you are measuring directly on the connector at the
camera location and not further back in a different location. This wire will switch to 12V while the
vehicle is in REVERSE and will be zero at other times. Cut this wire and connect the REVERSE
CAM 12V+ power connection from the Lockpick to the camera directly. Do not reconnect the
original camera power source wire or fail to cut the wire at the camera. Instead tape it up and
disregard it. The Lockpick will provide all necessary power and timing for the factory camera.
Failing to cut the wire or connecting the Lockpick power and factory power at the same time could
cause the reverse tail light to illuminate at improper times. Also, cutting the wire at a different
location other than directly on the camera connector could possibly interrupt power to other
functions such as the actual reverse taillights or rear obstacle detection systems.
5. If you do not currently have a rear view camera and want to add one to your vehicle, or if you wish
to install a second rear camera for trailer use, etc.,the Lockpick makes it easy. Connect your rear
cam video to the Lockpick module rear cam input on the Lockpick harness. If installing a 2nd rear
camera, connect the 2nd rear video to the 2nd Rear camera input labeled on the Lockpick module. The
REVERSE CAM 12V + power output provided on the Lockpick will be your source for rear and
second rear power. Also, a GROUND connection is provided on the Lockpick harness to make
powering your camera simple.
6. If you want to add a front camera or side cameras to your vehicle, the Lockpick is prewired and
programmed for exciting options. The Lockpick harness has a 12V power output labeled
ADDITIONAL CAM POWER 12V+ to automatically provide the power needs of your front and side
cameras or to provide power and control of an interior baby camera if desired. Connect the power
needs of your additional cameras to the camera power output and attach the GROUND connection of
your camera to the GROUND connection provided for you on the Lockpick harness. Connect the
video from your cameras to the video inputs labeled on your Lockpick module
7. Also present on your Lockpick harness is a 12V ACC output connection. This ACC output is created
by the Lockpick and can be used as a convenient 12V switched power source for many of your
accessories. It is rated for a constant 1.5 AMPs and will automatically turn on and off at the proper
times of your vehicle use. If your power needs are greater than 1.5 Amps, you may use the
CONSTANT 12V output conveniently provided by the Lockpick harness and switch it on and off
through a relay powered by the ACC power output of the Lockpick harness.
**NOTE: The connections for 12V Constant Battery power (YELLOW), ACC Ignition power (RED), GROUND
(BLACK), Reverse power(ORANGE W/STRIPE), Front/Baby cam power (RED W/STRIPE), are provided as a
BONUS in your wiring harness for you to use when connecting additional accessories such as a DVD player,
Game, Cameras, Radar detector, etc., without worry that they might drain your battery when the car is turned
off. The ACC wire can power up to 1.5 Amps constant. Higher loads should be connected with a relay.
** Do not attach the Constant or ACC wires directly to the vehicle wiring or ignition switch. The
Lockpick is plug and play for standard DVD/AUX/NAV/VIDEO/AUDIO/CAM unblocking and does
not require connections for power or ground. Connecting these Lockpick outputs to the vehicle wiring
can damage the unit and cause improper operations.
**
When the Lockpick Air is turned on for the first time, allow 30 seconds before operating the
various functions and TV mode. This allows the Lockpick to prepare the radio and screen views for
standard operations. After the first startup, the Lockpick will already have the TV mode active and
all touch screen options are ready for use. The Lockpick will automatically update the TV channels,
requiring only a couple of seconds, each time the TV mode is selected. During the time that
“Updating Channels” or “Initializing” is displayed on the TV mode screen, the touch screen options
are not available for selection.
LOCKPICK AIR OPERATIONS
The Lockpick Air automatically activates the TV mode and generates up to 9 pages of
touch screen options for simple user control. Touch the on-screen button to select the desired
function. **Mygig radio buttons and locations may vary with year and options present.
Select Radio/Media button
and then select the TV touch
screen tab
Select PAGE to advance
through Lockpick menus
Select LIST to display presets
on right of display as shown.
Displays information about
current selection or
instructions
Press VIEW VIDEO to see
WiFI, AUX, cameras, movies,
etc.
1.
2.
3.
**While “viewing video”, touch the
screen anywhere to overlay the
touch screen options again and
display the “HIDE VIDEO”
button. This returns you to the
standard radio view.
4.
Lockpick A/V Options Page 1
Select LOCKPICK tab to display software
revision. The unit is USB upgradable.
Select LPICK AIR to activate the WiFi
multimedia source. Press VIEW VIDEO to
see video on screen.
Select AUX A/V to activate the Lockpick
module RCA A/V inputs. Connect any
standard multimedia source. Press VIEW
VIDEO to see video on screen.
Reserved for future use.
Lockpick Camera Options Page 2
Select any of the camera inputs included on the
Lockpick AIR by pressing REAR CAM, FRONT
CAM, LEFT CAM, or RIGHT CAM.
Touch VIEW VIDEO to display the camera video.
**Bonus feature: Press power button
2x while in modes other than TV (ex.
AM, FM, SAT, etc.) to display
camera selected here. Press 2x again
to turn off camera.
Also, camera source selected here sets the default
for which camera will be displayed when activated
manually while in modes other than TV.
Automatic cameras will activate and
display while the radio is in any
mode (AM, FM, etc.)
**While any automatic camera is
showing, you can temporarily turn
it off and return to the standard
screen by pressing the power button
2x.
Lockpick Auto Cams Options Page 3
1. Touch any of the 3 options for automatic
control of connected cameras. Then touch
CHANGE OPT to turn ON or OFF the feature
selected.
2. Set AUTO REAR to ON, to automatically
activate rear cam while in reverse gear.
Default setting is ON. If no rear cam is
connected, change option to OFF to avoid
blank screen view while in reverse.
3. Set AUTO FRONT to ON, to turn on a
forward facing camera automatically while
driving less than 7 MPH to aid in parking.
Default setting is OFF.
4. Set AUTO TURNS to ON, to turn on left or
right cameras whenever the corresponding turn
signal is activated. Default setting is OFF.
Lockpick Options Page 4
1. Touch to arm 0 – 60 mph timer. Timer will
activate when vehicle is in motion and stop
automatically when 60 mph is reached.
Elapsed time will display on radio.
2. Touch to arm 0 – 10 second timer. Timer will
activate when vehicle is in motion and stop
automatically after 10 seconds. Maximum
speed reached will display on radio.
3. Touch to STOP either timer.
4. Touch to Reset time or speed to 0.
Status of selected options will display
in this location. Headrest selections are
independent of the source set for the
front screen (dual zone).
Lockpick Headrest Output Options Page 5
1. Touch to display the current source that is
configured to display on an external screen or
headrest.
2. Set to SCRN, to make the output the same as
what it being sent to the front screen.
3. Set to AIR, to send the audio and video from
the streaming WiFi source out to the second
screen.
4. Set to AUX, to send the audio and video from
any device connected to the Aux A/V inputs,
out to the second screen.
The LOCKPICK AIR includes camera
inputs which may be selected to show
exterior views on a separate screen.
They can also be used for viewing
interior areas as desired (ex. baby
monitor, lip reading of passengers,
The VES mode is available on the
media radio screen view (same HDD,
DVD,etc.) Within the VES mode are
factory options to send the factory
DVD audio and video to an additional
screen. A/V output cables are included
in your Lockpick radio harness near
the white connectors if you would like
to use this bonus feature.
Lockpick Headrest Output Options Page 6
1. Set to REAR to always send the rear camera
video to a second screen. Note: Factory rear
camera video cannot be output to a second
screen. Aftermarket rear cam will show if
selected.
2. Set to FRONT, to always send the front
camera video to a second screen
3. Set to LEFT to always send the left camera
video to a second screen
4. Set to RIGHT to always send the right camera
video to a second screen.
Lockpick Additional Options Page 7
1. Touch one of the 3 additional options. Then
touch CHANGE OPT to turn ON or OFF the
feature selected.
2. Set HR AUTOCAMS to ON, to allow rear
cam, front cam or turn signal cams to interrupt
headrest output video and show the camera
temporarily whenever an automatic camera is
activated (ex. Rear cam while in reverse, front
or turn cams when activated). Default is OFF.
3. Select to automatically provide override for
navigation address entry (if equipped) and for
automatic enabling of VIEW VIDEO button.
(default is ON) *See operation note below
4. Enables the rear seat entertainment mode
(VES) on vehicles not already factory
equipped. Default setting is OFF.
*If AUTO OVR is set to OFF, (manual mode), press Uconnect button 2x while in any mode
(DVD, VES, SAT TV, Nav input, etc.) as needed to temporarily turn override on and off.
Lockpick Additional Options Page 8
1. Touch any of the 3 options for automatic
control of connected cameras. Then touch
CHANGE OPT to turn ON or OFF the feature
selected.
2. Set to ON to enable an alternate rear camera to
display when the vehicle is placed in Reverse.
(useful when pulling trailers, etc.) Default is
OFF.
3. Select NAV if your Mygig radio is equipped
with Navigation features. (default is ON). If
your radio does not have navigation features,
turn this option OFF to provide proper
override functions.
4. Reserved for future updates.
Lockpick Factory TV Page 9
Some older model vehicles were equipped with
factory Sat TV. If your vehicle is already equipped
with factory satellite TV, the Lockpick will generate a
9th page of options which includes the original three
factory TV channels. The normal operation of these
factory channels are not affected by the installation of
the Lockpick.
The Lockpick will also fully enable the VIEW
VIDEO button for these factory channels.
ADDITIONAL MENU OPTIONS
The LOCKPICK AIR includes an additional set of comprehensive menus which are
accessible in any radio mode and activated by steering wheel or remote control
(included). This extended menu allows fast and convenient control of many Lockpick
functions and programming options.
Press and hold the Source button on the back of your steering wheel (see Lockpick
steering wheel diagram) or press the MENU button on your remote control.
The LOCKPICK AIR menu will open and display the current status of multiple
options as well as allow the user to change each selection with the remote control or
steering wheel buttons. The menu will display with an asterisk next to each item that is
activated. In this view, the LOCKPICK AIR video source is shown as selected and available
for viewing in the TV mode created by the LOCKPICK. If AUX A/V is selected, it will then
become the video source viewed when the radio is returned to the TV mode.
Selecting “CAMERAS” will display a selection of all camera video inputs and allow the user
the select which camera view they would like to view immediately on the radio screen.
Selecting “HR OPTIONS” (headrest) will allow the user to determine which video to send
to an additional screen or headrest multimedia system.
Scrolling further down the menu will reveal the “ADDITIONAL OPTIONS” selection as well
as Language Options (English or Spanish), and INFO for displaying current device
software, hardware and serial number.
The “ADDITIONAL OPTIONS” selection allows the user to determine the desired
operations of any connected camera as well as numerous additional LOCKPICK features.
Shown above, the “ADDITIONAL OPTIONS” menu allows the user to:
•
•
•
•
•
•
•
Select a rear camera to display automatically while the vehicle is in reverse
(default ON)
Set a second rear camera to be the one seen while the vehicle is reverse
Enable the front camera to activate automatically while the car is below 7 mph and
turn off when the vehicle accelerates past 7 mph
Enable side cameras to activate automatically when the corresponding turn signal
is used
Send the video from any camera which is automatically activated, to a separate
screen or headrest display
NAV RADIO should be selected if the radio connected to the LOCKPICK is
navigation equipped. This determines the type of OVERRIDE the LOCKPICK AIR will
use to allow navigation input while in motion
ADD VES will enable an additional mode (VES) to your radio if not already
equipped. Included in your harness are VES A/V outputs which could allow you to
send the Audio and Video from the MYGIG radio DVD player out to a separate
screen or headrests. DO not enable if already VES equipped or conflict will occur.
•
ADD TV is by default “ON” to add the SAT TV mode to your radio. In some areas of
the world (Europe), the MYGIG radio does not have the software included to be
able to use this feature. In these countries, the LOCKPICK allows the user to turn
off SAT TV and instead use a different method of multimedia operation. If your
radio cannot support SAT TV, turn off the ADD TV and insure that the vehicle is
already equipped with VES, or that the Lockpick ADD VES mode has been activated.
In this configuration, place the radio in the VES mode instead of SAT TV for
multimedia operations and use the remote control for LOCKPICK selections.
LOCKPICK AIR WIFI OPERATION
The LOCKPICK AIR includes WiFi capabilities which allow streaming wireless
operations from smart phones, tablets and more . Included in the Lockpick capabilities are
multiple modes of streaming airplay to allow different types of devices to send video and
audio to the Lockpick and Mygig radio. When the Lockpick Air mode is selected and the
VIEW VIDEO button is pressed, the Lockpick will display the current Airplay mode. If your
device requires a different Airplay mode for streaming, press the AIR MODE button on the
remote control or momentarily press the source button on the back of your steering
wheel. The Lockpick will toggle between the following three formats.
DLNA (iPhone, iPad)
MIRACAST (Android)
WIDI (Intel)
To begin pairing with the Lockpick, simply insure that the WiFi feature of your
device is enabled and if prompted, select Lockpick Air to connect.
Turn on the Mirror function on your Apple or Android device and full multimedia
operation is transferred to the Lockpick for viewing and listening. This can include music
with associated album art, map, navigation, text messaging, pictures, internet, games,
YouTube, Netflix (see Apple restrictions page 1), and more. Apple devices will stream
videos recorded from the device itself, but will not stream iTunes videos or DRM
copyrighted media. Android devices have no such restriction and will even stream movies
downloaded and saved on the device.
Make sure that your device is running the latest software available from the manufacturer
as earlier versions may not support streaming or mirroring.
Thank you for your trust in Coastal Electronic Technologies, Inc.
Installation Q & A:
1.
I installed the Lockpick and now my radio does not turn on.
Check all interface switches, especially 1 and 2 and correctly set them for the vehicle type (see application
chart). Check to make sure you have fully inserted the Gray and White connectors behind the radio
without bending pins.
2.
When I put the car in Reverse, the radio screen blanks out. I do not have a rear view camera.
The Lockpick automatically activates a rear view camera input for your radio. If you do not intend to
install a rear view camera or do not want it activated automatically, refer to the Lockpick options to
disable the AUTO REAR function.
3.
I installed the Lockpick and now my factory VES rear entertainment is intermitting.
The Lockpick is able to create a VES mode within your radio, to give an installer the ability to output the
audio and video of the factory radio DVD player if desired, to an additional screen. The default setting of
the Lockpick options is VES OFF. If you change the option and turn it ON when you already have a
factory VES system, the communication will conflict. Set the option to OFF to restore factory VES
operation.
4.
I turned on one of the Cameras, or Aux A/V functions created by the Lockpick and all I see is a flashing
picture or blank screen when I try to look at the video.
This means you don’t have anything connected or, do not have the device turned on to supply a video
input. The radio screen will be blank or flash when there is no video from your connected device. Common
solutions for camera pictures are normally resolved by rechecking the power connections and insuring that
all cameras are powered by the connections provided on the Lockpick harness. This includes the factory
rear view camera, if your vehicle requires a Lockpick connection to power it while in a gear other than
reverse. Also, check to make sure you have fully inserted the White connector on the Lockpick harness
and the video connections for your device are plugged in. Connectors not fully inserted may create
intermitting operations.
Lockpick Air Remote Control Operations
The Remote control for the Lockpick Air is battery powered (provided) and
communicates with infra-red light to the included pickup sensor. The sensor plugs
into the Lockpick module and should be placed in the vehicle at a location easily
targeted by the remote. The steering wheel functions can be used along with the
remote control functions at any time. The remote control can allow quicker access
to many of the features of the Lockpick Air without navigating the menu structure
needed by the steering wheel controls. Before using the remote for the first time,
be sure and pull the plastic tab from the battery compartment to engage battery
connections.
Activate Lockpick Menus, Air WIFI
functions, or Aux A/V inputs.
OFF turns off any audio or video
function
Quickly view any camera connected
Select BACK to move to last selected
menu or EXIT to turn off Menu.
Activate DVD Override ON or OFF in
vehicles equipped with a factory
DVD player
Controls all Lockpick menu scrolling
and selecting operations.
Activate Nav Override ON or Off
Automatically times out after 60
seconds.
Select Airplay mode. Toggle
between DLNA (Apple), Miracast
(Android), and WiDi, (Intel).
VID ON-OFF selects and displays
video only from AIR or AUX without
interrupting current radio sound.
Great for video only uses like
Internet or Map operations.
Quickly select output to be viewed
and heard on external screens
Program any connected camera to
automatically turn on and off
according to gear, speed, or turn
signal activation. Radio will display
and confirm selection on-screen.
Optional buttons
Lockpick Air USB Updates
The Lockpick Air includes the ability to be updated via a USB connection to a laptop
PC. If directed to update by one of our technicians, consult our website at
CoastalEtech.com/usbupdate.htm for specific downloads and instructions for your
Lockpick Air. It is not recommended to update the Lockpick without first consulting a
technician.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising