Z9PE-D16
Z9PE-D16/2L
Motherboard
Z9PE-D16 Series
E7223
Revised Edition V2
April 2012
Copyright © 2012 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means,
except documentation kept by the purchaser for backup purposes, without the express written permission
of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND
SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY
OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
ii
Contents
Notices......................................................................................................... vii
Federal Communications Commission Statement............................ vii
Canadian Department of Communications Statement...................... vii
REACH ........................................................................................... vii
Safety information..................................................................................... viii
Electrical safety................................................................................ viii
Operation safety............................................................................... viii
About this guide.......................................................................................... ix
How this guide is organized...............................................................ix
Where to find more information..........................................................ix
Conventions used in this guide...........................................................x
Typography.........................................................................................x
Z9PE-D16 Series specifications summary................................................ xi
Z9PE-D16 Series specifications summary............................................... xii
Chapter 1: Product introduction
1.1
Welcome!....................................................................................... 1-3
1.3
Serial number label....................................................................... 1-4
1.2
1.4
Package contents.......................................................................... 1-3
Special features............................................................................. 1-4
1.4.1
1.4.2
Chapter 2:
2.1
2.2
2.4
2.5
Innovative ASUS features................................................ 1-6
Hardware information
Before you proceed...................................................................... 2-3
Motherboard overview.................................................................. 2-4
2.2.1
Placement direction......................................................... 2-4
2.2.3
Motherboard layout.......................................................... 2-5
2.2.2
2.3
Product highlights............................................................ 1-4
2.2.4
Screw holes..................................................................... 2-4
Layout contents................................................................ 2-6
Central Processing Unit (CPU).................................................... 2-8
2.3.1
Installing the CPU............................................................ 2-8
2.4.1
Overview........................................................................ 2-13
System memory.......................................................................... 2-13
2.4.2
Memory Configurations.................................................. 2-13
Expansion slots........................................................................... 2-16
2.5.1
Installing an expansion card.......................................... 2-16
2.5.3
Interrupt assignments.................................................... 2-17
2.5.2
Configuring an expansion card...................................... 2-16
iii
Contents
2.5.4
PCI Express x16 slot (x16 link)...................................... 2-17
2.5.6
PIKE slots...................................................................... 2-17
2.5.5
2.5.7
2.6
2.7
2.5.8
PCI Express x16 slot (x8 link)........................................ 2-17
Installing an ASUS PIKE RAID card.............................. 2-19
Installing ASMB6 management board............................ 2-21
Jumpers....................................................................................... 2-22
Connectors.................................................................................. 2-26
2.7.1
2.7.2
Rear panel connectors................................................... 2-26
Internal connectors........................................................ 2-27
2.8 Internal LEDs...................................................................................... 2-37
Chapter 3:
3.1
3.2
Starting up for the first time......................................................... 3-3
Powering off the computer........................................................... 3-4
3.2.1
3.2.2
Chapter 4:
4.1
4.1.3
BUPDATER utility............................................................ 4-5
ASUS EZ Flash 2 Utility................................................... 4-4
BIOS setup program..................................................................... 4-7
4.2.1
BIOS menu screen........................................................... 4-8
4.2.3
Menu items...................................................................... 4-9
4.2.5
4.2.6
4.2.7
4.2.8
4.2.9
Menu bar.......................................................................... 4-8
Submenu items................................................................ 4-9
Navigation keys................................................................ 4-9
General help.................................................................... 4-9
Configuration fields.......................................................... 4-9
Pop-up window................................................................ 4-9
Scroll bar.......................................................................... 4-9
Main menu................................................................................... 4-10
4.3.1
4.3.2
System Date [Day xx/xx/xxxx]........................................ 4-10
System Time [xx:xx:xx].................................................. 4-10
Advanced menu.......................................................................... 4-11
4.4.1
CPU Configuration..........................................................4-11
4.4.3
Chipset Configuration.................................................... 4-16
4.4.2
iv
BIOS setup
ASUS CrashFree BIOS 3 utility....................................... 4-3
4.2.4
4.4
Using the dual function power switch............................... 3-4
4.1.1
4.2.2
4.3
Using the OS shut down function..................................... 3-4
Managing and updating your BIOS............................................. 4-3
4.1.2
4.2
Powering up
CPU Power Management Configuration........................ 4-14
Contents
4.4.4
PCH SATA Configuration............................................... 4-21
4.4.6
PCI Subsystem Settings................................................ 4-23
4.4.5
4.4.7
4.4.8
4.4.9
4.4.10
4.4.11
4.4.12
4.4.13
4.4.14
4.4.15
4.4.16
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.4.17
Onboard LAN Configuration........................................... 4-26
Intel TXT(LT-SX) Configuration...................................... 4-27
USB Configuration......................................................... 4-28
Trusted Computing......................................................... 4-29
ACPI Settings................................................................. 4-30
WHEA Configuration...................................................... 4-31
APM setting.................................................................... 4-31
Serial Port Console Redirection..................................... 4-32
ME Subsystem............................................................... 4-35
Legacy Devices Configuration....................................... 4-35
Runtime Error Logging................................................... 4-36
Server Mgmt menu...................................................................... 4-37
4.5.1
4.5.2
System Event Log.......................................................... 4-38
BMC network configuration............................................ 4-39
Event Logs menu........................................................................ 4-40
4.6.1
Change Smbios Event Log Settings.............................. 4-40
Boot menu................................................................................... 4-42
Monitor menu.............................................................................. 4-44
Security menu............................................................................. 4-45
Tool menu.................................................................................... 4-47
Exit menu..................................................................................... 4-47
Chapter 5:
5.1
PCH SCU Configuration................................................ 4-23
RAID configuration
Setting up RAID............................................................................. 5-3
5.1.1
RAID definitions............................................................... 5-3
5.1.3
Setting the RAID item in BIOS......................................... 5-4
5.1.2
5.1.4
Installing hard disk drives................................................. 5-4
RAID configuration utilities............................................... 5-4
5.2LSI Software RAID Configuration Utility .................................... 5-5
5.2.1
Creating a RAID set......................................................... 5-6
5.2.3
Initializing the virtual drives............................................ 5-13
5.2.2
5.2.4
5.2.5
5.2.6
Adding or viewing a RAID configuration........................ 5-12
Rebuilding failed drives.................................................. 5-17
Checking the drives for data consistency...................... 5-19
Deleting a RAID configuration........................................ 5-22
Contents
5.2.7
5.2.8
Selecting the boot drive from a RAID set....................... 5-23
Enabling WriteCache..................................................... 5-24
5.3Intel Rapid Storage Technology enterprise SCU/SATA Option
®
ROM Utility.................................................................................. 5-25
5.3.1
Creating a RAID set....................................................... 5-27
5.3.3
Deleting a RAID set....................................................... 5-30
5.3.2
5.3.4
5.3.5
5.3.6
5.3.7
Creating a Recovery set................................................ 5-28
Resetting disks to Non-RAID......................................... 5-31
Exiting the Intel® Rapid Storage Technology utility......... 5-32
Rebuilding the RAID...................................................... 5-32
Setting the Boot array in the BIOS Setup Utility............. 5-34
5.4Intel® Rapid Storage Technology enterprise Utility (Windows)5-35
5.4.1
Creating a RAID set....................................................... 5-36
5.4.3
Delete volume................................................................ 5-39
5.4.2
5.4.4
Chapter 6:
6.1
Change Volume Type..................................................... 5-38
Preferences.................................................................... 5-40
Driver installation
RAID driver installation................................................................ 6-3
6.1.1
6.1.2
Creating a RAID driver disk............................................. 6-3
Installing the RAID controller driver................................. 6-5
6.2Intel® chipset device software installation................................ 6-15
6.3Intel@ Network Connections Software installation.................. 6-17
6.4
VGA driver installation............................................................... 6-20
6.6
Microsoft .NET Framework 3.5 SP1........................................... 6-24
6.5Intel® C600 Series Chipset SCU SATA RAID Driver.................. 6-23
6.7Intel® Rapid Storage Technology enterprise 3.0 installation.. 6-25
6.8Intel® I350 Gigabit Adapters Driver installation........................ 6-28
6.9Management applications and utilities installation................. 6-32
6.9.1
Running the support DVD.............................................. 6-32
6.9.3
Utilities menu................................................................. 6-33
6.9.2
6.9.4
6.9.5
Appendix:
A.1
A.2
Drivers menu.................................................................. 6-32
Make disk menu............................................................. 6-33
Contact information........................................................ 6-33
Reference information
Z9PE-D16 block diagram..............................................................A-3
Z9PE-D16/2L block diagram.........................................................A-4
ASUS contact information........................................................................... 1
vi
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with manufacturer’s instructions, may
cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
•
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and Restriction
of Chemicals) regulatory framework, we publish the chemical substances in our
products at ASUS REACH website at http://csr.asus.com/english/REACH.htm.
vii
Safety information
Electrical safety
•
•
•
•
•
•
To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
When adding or removing devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are
connected. If possible, disconnect all power cables from the existing system
before you add a device.
Before connecting or removing signal cables from the motherboard, ensure
that all power cables are unplugged.
Seek professional assistance before using an adapter or extension cord.
These devices could interrupt the grounding circuit.
Make sure that your power supply is set to the correct voltage in your area.
If you are not sure about the voltage of the electrical outlet you are using,
contact your local power company.
If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safety
•
•
•
•
•
•
Before installing the motherboard and adding devices on it, carefully read all
the manuals that came with the package.
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Do not place the product in
any area where it may become wet.
Place the product on a stable surface.
If you encounter technical problems with the product, contact a qualified
service technician or your retailer.
DO NOT throw the motherboard in municipal waste. This product has been
designed to enable proper reuse of parts and recycling. This symbol of the
crossed out wheeled bin indicates that the product (electrical and electronic
equipment) should not be placed in municipal waste. Check local regulations for
disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste.
This symbol of the crossed out wheeled bin indicates that the battery should not
be placed in municipal waste.
viii
About this guide
This user guide contains the information you need when installing and configuring
the motherboard.
How this guide is organized
This user guide contains the following parts:
•
•
•
•
•
•
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new
technologies it supports.
Chapter 2: Hardware information
This chapter lists the hardware setup procedures that you have to perform
when installing system components. It includes description of the switches,
jumpers, and connectors on the motherboard.
Chapter 3: Powering up
This chapter describes the power up sequence and ways of shutting down
the system.
Chapter 4: BIOS setup
This chapter tells how to change system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter 5: RAID configuration
This chapter provides instructions for setting up, creating, and configuring
RAID sets using the available utilities.
Chapter 6: Driver installation
This chapter provides instructions for installing the necessary drivers for
different system components.
Appendix: Reference information
This appendix includes additional information that you may refer to when
configuring the motherboard.
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
2.
ASUS websites
The ASUS website provides updated information on ASUS hardware and
software products. Refer to the ASUS contact information.
Optional documentation
Your product package may include optional documentation, such as warranty
flyers, that may have been added by your dealer. These documents are not
part of the standard package.
ix
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following
symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself
when trying to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to help you complete a
task.
Typography
Bold text
Indicates a menu or an item to select.
Italics
Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greaterthan sign means that you must press the
enclosed key.
Example: <Enter> means that you must press
the Enter or Return key.
<Key1+Key2+Key3>
If you must press two or more keys
simultaneously, the key names are linked with
a plus sign (+).
Example: <Ctrl+Alt+Del>
Command
Means that you must type the command
exactly as shown, then supply the required
item or value enclosed in brackets.
Example: At the DOS prompt, type the
command line: format A:/S
Z9PE-D16 Series specifications summary
Model Name
Processor Support / System Bus
Z9PE-D16
Z9PE-D16/2L
2 x Socket LGA 2011
®
®
Intel Xeon processor E5-2600 product family
QPI 6.4/7.2/8.0 GT/s
Intel® C602-A
Core Logic
EEB, 12” x 13”
Form Factor
ASUS Features Fan Speed Control V
V
Rack Ready (Rack
and Pedestal dual
use)
V
ASWM Enterprise
16 (4 Channels per CPU, 8DIMM per CPU)
Memory
Total Slots
1.5V/ 1.35V
Voltage
Maximum up to 512GB
Capacity
DDR3 1066/1333/1600 RDIMM
Memory Type
DDR3 1066/1333 UDIMM (ECC/non-ECC)
DDR3 1066/1333 LRDIMM
2GB, 4GB, 8GB, 16GB* (RDIMM)
Memory Size
2GB, 4GB, 8GB* (UDIMM)
8GB, 16GB, 32GB* (LRDIMM)
6
Expansion Slots Total PCI/PCI-X/
PCI-E Slots
1 x PCI-E x16 (X8 Gen3 link, Auto switch to x8 link if PCIE
PCIE 1
2 is occupied, MIO supported, White, from CPU 1)
1 x PCI-E x16 (X16 Gen3 link, Auto switch to x8 link if
PCIE 2
PCIE 1 is occupied, White, from CPU 1)
1 x PCI-E x16 (X16 Gen3 link, Black, from CPU 2)
PCIE 3
1 x PCI-E x16 (X16 Gen3 link, White, from CPU 1)
PCIE 4
1 x PCI-E x16 (X16 Gen3 link, Black, from CPU 2)
PCIE 5
1 x PCI-E x16 (X8 Gen3 link, Black, from CPU 2)
PCIE 6
1 x PIKE Slot for Storage expansion (White, from CPU 1)
Additional Slot 1
Storage
SATA Controller
Intel® C602-A:
<AHCI>
2 SATA 6Gb/s ports; 4 SATA 3Gb/s ports
Intel® RSTe (for Windows only)
(Support software RAID 0, 1, 10 & 5)
LSI® MegaRAID (for Linux/Windows)
(Support software RAID 0, 1, 10)
SAS Controller
Networking
LAN
Graphic
VGA
<SCU>
4 SATA 3Gb/s ports
Intel® RSTe (for Windows only)
(Support software RAID 0, 1, 10 & 5 for all SATA ports)
Optional kits:
ASUS PIKE 2008 8-port SAS 6G RAID card
ASUS PIKE 2008/IMR 8-port SAS 6G RAID card
ASUS PIKE 2108 8-port SAS 6G HW RAID card
1 x Quad Port Intel®
1 x Dual Port Intel®
Ethernet Controller i350Ethernet Controller i350AM4 GbE LAN
AM2 GbE LAN
ASPEED® AST2300 + 16MB VRAM
(continued on the next page)
xi
Z9PE-D16 Series specifications summary
Onboard I/O
Connectors
TPM Header
PSU Connector
Management
Connector
USB Connectors
Rear I/O
Connectors
Monitoring
Environment
Fan Header
Chassis Intruder
Serial Port Header
External USB Port
VGA Port
RJ-45
PS/2 KB/Mouse
CPU Temperature
FAN RPM
1
24-pin SSI power connector + 2*8-pin SSI 12V power
connector
Onboard socket for management card
3 x USB pin header (up to 5 devices, one for internal Type
A USB connector)
8 x 4pin
1
2
2
1
4 + 1 Management Port
2 + 1 Management Port
2
V
V
Operation temperature: 10°C – 35°C
Non operation temperature: -40°C – 70°C
Non operation humidity: 20% – 90%
(Non condensing)
*Refer to ASUS Server AVL for latest update.
**Specifications are subject to change without notice.
xii
This chapter describes the motherboard
features and the new technologies it supports.
1
Product
introduction
Chapter summary
1
1.1
Welcome........................................................................................ 1-3
1.3
Serial number label....................................................................... 1-4
1.2
1.4
Package contents.......................................................................... 1-3
Special features............................................................................. 1-4
ASUS Z9PE-D16 Series
1.1
Welcome!
Thank you for buying an ASUS® Z9PE-D16 Series motherboard!
The motherboard delivers a host of new features and latest technologies, making it
another standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it, check the
items in your package with the list below.
1.2
Package contents
Check your motherboard package for the following items.
Z9PE-D16 Series
ASMB6-iKVM module
SATA DOM cable
Cables
SATA cable
Support CD
Application CD
ASWM Enterprise
SDVD
Packing Qty.
Standard Bulk Pack
1
--1
1
1
1
1
Motherboard User
Guide
1
1
ASMB6-iKVM User
Guide
1
1
1pc per carton
10pcs per carton
ASMB6-iKVM SDVD
Documentation
Standard Gift Box
Pack
1
1
10
1
If any of the above items is damaged or missing, contact your retailer.
Optional items
PIKE 2108
PIKE 2008/IMR
PIKE 2008
ASUS Z9PE-D16 Series
Description
LSI 8-port SAS2 6G RAID card
LSI 8-port SAS2 6G RAID card
LSI 8-port SAS2 6G RAID card
1-3
1.3
Serial number label
Before requesting support from the ASUS Technical Support team, you must take
note of the motherboard's serial number containing 12 characters xxS2xxxxxxxx
shown as the figure below. With the correct serial number of the product, ASUS
Technical Support team members can then offer a quicker and satisfying solution
to your problems.
Z9PE-D16
xxS2xxxxxxxx
1.4
Special features
1.4.1
Product highlights
Made
in
China
合格
Latest Processor Technology
The motherboard supports the latest Intel Xeon® processor E5-2600 product family
in LGA 2011 package with integrated memory controller to support 4 channel (8
DIMM prt CPU) DDR3 memory. Intel Xeon® processor E5-2600 product family
supports Intel QuickPath Interconnect (QPI) with a system bus of up to 8.0GT/s.
Optimized Intel® Turbo Boost Technology
Optimized Intel® Turbo Boost Technology opportunistically and automatically allows
the processor to run faster than the marked frequency if the processor is operating
below power, temperature and current limits.
Intel® Hyper Threading
The thread-level parallelism on each processor makes more efficient use of the
processor resources, higher processing throughout and improved performance on
today's multi-threaded software.
Intel® EM64T
The motherboard supports Intel® processors with the Intel® EM64T (Extended
Memory 64 Technology). The Intel® EM64T feature allows your computer to run on
64-bit operating systems and access larger amounts of system memory for faster
and more efficient computing.
1-4
Chapter 1: Product introduction
DDR3 memory support
The Z9PE-D16 supports DDR3 memory that features data transfer rates of
1600/1333/1066 MHz to meet the higher bandwidth requirements of server
and workstation applications. The 4-channel DDR3 architecture boosts system
performance, eliminating bottlenecks with peak bandwidth of up to 52GB/s. This
voltage reduction limits the power consumption and heat generation of DDR3
which makes it an ideal memory solution. Also, the motherboard can support LRDIMM (Load reduced DIMM) which uses a specially designed buffer to reduce the
data load to a single load and can increase overall server system memory capacity.
PCIe 3.0
The motherboard supports the latest PCIe 3.0 device, which doubles the delivered
bandwidth of PCIe 2.0. This enhances system performance while still providing
backward compatibility to PCIe 2.0.
Intel® I350 Gigabit LAN Solution
The motherboard comes with an integrated quad port Gigabit LAN controller
which provides a total solution for your networking needs. The onboard Intel® I350
Gigabit LAN controller can save platform power with EEE and DMA coordination
features and enhances management features with OS2BMC and MCTP support.
Enhanced Intel SpeedStep Technology (EIST)
The Enhanced Intel SpeedStep Technology (EIST) intelligently manages the
CPU resources by automatically adjusting the CPU voltage and core frequency
depending on the CPU loading and system speed or power requirement.
Serial ATA II technology
The motherboard supports the Serial ATA II 3 Gb/s technology through the Serial
ATA interface and Intel® C600 chipset. The Serial ATA II specification provides
twice the bandwidth of the current Serial ATA products with a host of new
features, including Native Command Queuing (NCQ), Power Management (PM)
Implementation Algorithm, and Hot Swap. Serial ATA allows thinner, more flexible
cables with lower pin count and reduced voltage requirements.
Serial ATA III technology
The motherboard supports the Serial ATA III technology through the Serial ATA
interface and Intel® C600 chipset, delivering up to 6Gb/s data transfer rates.
Additionally, get enhanced scalability, faster data retrieval, double the bandwidth of
current bus systems.
USB 2.0 technology
The motherboard implements the Universal Serial Bus (USB) 2.0 specification,
dramatically increasing the connection speed from the 12 Mbps bandwidth on USB
1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is backward compatible with USB 1.1.
ASUS Z9PE-D16 Series
1-5
Temperature, fan, and voltage monitoring
The CPU temperature is monitored to prevent overheating and damage. The
system fan rotations per minute (RPM) is monitored for timely failure detection.
The chip monitors the voltage levels to ensure stable supply of current for critical
components.
1.4.2
Innovative ASUS features
ASUS Fan Speed control technology
The ASUS Fan Speed control technology smartly adjusts the fan speeds according
to the system loading to ensure quiet, cool, and efficient operation.
PIKE (Proprietary I/O Kit Expansion)
PIKE is an on-demand upgrade kit for users. This ASUS unique feature enables
users to choose their preferred I/O solutions. ASUS provides multiple SAS
solutions for different segments and purposes and PIKE saves lots of validation
efforts and hardware cost for end users. Moreover, the special patent design offers
multiple I/O solutions without occupying the Slot 6 in 1U system.
1-6
Chapter 1: Product introduction
This chapter lists the hardware setup
procedures that you have to perform
when installing system components. It
includes description of the jumpers and
connectors on the motherboard.
Chapter 2:
2
Hardware
information
Chapter summary
2
2.1
Before you proceed...................................................................... 2-3
2.3
Central Processing Unit (CPU).................................................... 2-8
2.2
2.4
2.5
2.6
2.7
2.8 Motherboard overview.................................................................. 2-4
System memory.......................................................................... 2-13
Expansion slots........................................................................... 2-16
Jumpers....................................................................................... 2-22
Connectors.................................................................................. 2-26
Internal LEDs............................................................................... 2-37
ASUS Z9PE-D16 Series
2.1
Before you proceed
Take note of the following precautions before you install motherboard components or change
any motherboard settings.
•
Unplug the power cord from the wall socket before touching any
component.
•
Use a grounded wrist strap or touch a safely grounded object or a metal
object, such as the power supply case, before handling components to
avoid damaging them due to static electricity.
•
Hold components by the edges to avoid touching the ICs on them.
•
Whenever you uninstall any component, place it on a grounded antistatic
pad or in the bag that came with the component.
•
Before you install or remove any component, ensure that the power supply
is switched off or the power cord is detached from the power supply. Failure
to do so may cause severe damage to the motherboard, peripherals, and/or
components.
Standby Power LED (SB_PWR1)
The motherboard comes with a standby power LED. The green LED lights up to
indicate the system AC power cable plug or not. This is a reminder that you should
shut down the system and unplug the power cable before removing or plugging
in any motherboard component. The illustration below shows the location of the
onboard LED.
ASUS Z9PE-D16 Series
2-3
2.2
Motherboard overview
Before you install the motherboard, study the configuration of your chassis to
ensure that the motherboard fits into it.
To optimize the motherboard features, we highly recommend that you install it in an
SSI EEB 2011 1.0 compliant chassis.
Ensure to unplug the chassis power cord before installing or removing the
motherboard. Failure to do so can cause you physical injury and damage
motherboard components!
2.2.1
Placement direction
When installing the motherboard, ensure that you place it into the chassis in the
correct orientation. The edge with external ports goes to the rear part of the chassis
as indicated in the image below.
2.2.2
Screw holes
Place ten (10) screws into the holes indicated by circles to secure the motherboard
to the chassis.
DO NOT overtighten the screws! Doing so can damage the motherboard.
Place this side towards
the rear of the chassis
2-4
Chapter 2: Hardware information
2.2.3
Motherboard layout
Z9PE-D16
Z9PE-D16/2L
ASUS Z9PE-D16 Series
2-5
2.2.4
Layout contents
Slots/Soocket
Page
1.
CPU sockets
2-8
2.
DDR3 sockets
2-13
3.
PCI Express x8 / PCI Express x16 slots
2-16
Jumpers
2-6
Page
1.
Clear RTC RAM (CLRTC1)
2-22
2.
VGA controller setting (3-pin VGA_SW1)
2-23
3.
LAN controller setting (3-pin LAN_SW1)
2-23
4.
LSI MegaRAID or Intel RSTe selection jumper (3-pin RAID_SEL1)
2-24
5.
ME firmware force recovery setting (3-pin ME_RCVR1)
2-24
6.
DDR3 thermal event setting (3-pin DIMMTRIP1)
2-25
7.
PMBus 1.2 PSU select jumper (3-pin SMART_PSU1)
2-25
Rear panel connectors
Page
1.
PS/2 mouse port (green)
2-26
2.
DM_LAN 1 (RJ-45) port
2-26
3.
LAN 1 (RJ-45) port
2-26
4.
LAN 2 (RJ-45) port
2-26
5.
LAN 3 (RJ-45) port (Z9PE-D16 only)
2-26
6.
LAN 4 (RJ-45) port (Z9PE-D16 only)
2-26
7.
PS/2 keyboard port (purple)
2-26
8.
USB 2.0 ports 1 and 2
2-26
9.
Video Graphics Adapter port
2-26
Chapter 2: Hardware information
Internal connectors
Page
1.
Serial ATA 6.03/3.0 Gb/s connectors
(7-pin SATA6G_1-2 [Blue], 7-pin SATA 3G_[Black]))
2-27
2.
SATA connector - ISAS connectors
3.
Hard disk activity LED connector (4-pin HDLED1)
2-28
4.
SAS connector - PSAS connectors
5.
USB connectors
(10-1 pin USB34, USB56; A-Type USB10)
6.
CPU, front and rear fan connectors
(4-pin CPU_FAN1-2, FRNT FAN1-4, REAR FAN 1-2)
2-31
7.
Serial General Purpose Input/Output connectors
(8-1 pin PSGPIO 1/2, ISGPIO1/2, SGPIO1)
2-32
8.
Serial port connectors (10-1 pin COM1/COM2)
9.
TPM connector (20-1-pin TPM)
2-32
10.
EATX power connectors (24-pin EATXPWR1, 8-pin EATX12V1/EATXV2, PSUSMB1)
11.
System panel connector (20-1 pin PANEL1)
12.
Auxiliary panel connector (20-2 pin AUX_PANEL1)
2-29
2-29
2-30
2-33
2-34
2-35
2-36
Internal LEDs
Page
1.
DIMM warning LED (ERR_DIMMA1/2; ERR_DIMMB1/2;
ERR_DIMMC1/2; ERR_DIMMD1/2; ERR_DIMME1/2;
ERR_DIMMF1/2; ERR DIMMG1/2; ERR DIMMH1/2)
2-37
2.
BMC LED (BMC_LED1)
3.
CPU warning LED (ERR CPU1, ERR_CPU2)
2-38
4.
CATT LED
5.
Q-Code LEDs
ASUS Z9PE-D16 Series
2-38
2-39
2-39
2-7
2.3
Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA2011 socket designed for the
Intel® Xeon E5-2600 family processor.
2.3.1
•
Upon purchase of the motherboard, ensure that the PnP cap is on
the socket and the socket contacts are not bent. Contact your retailer
immediately if the PnP cap is missing, or if you see any damage to the PnP
cap/socket contacts/motherboard components. ASUS will shoulder the cost
of repair only if the damage is shipment/transit-related.
•
Keep the cap after installing the motherboard. ASUS will process Return
Merchandise Authorization (RMA) requests only if the motherboard comes
with the cap on the LGA2011 socket.
•
The product warranty does not cover damage to the socket contacts
resulting from incorrect CPU installation/removal, or misplacement/loss/
incorrect removal of the PnP cap.
Installing the CPU
To install a CPU:
1.
Locate the CPU socket on the motherboard.
Before installing the CPU, ensure that the socket box is facing toward you and
the load lever is on your left.
2-8
Chapter 2: Hardware information
2.
Press the left load lever with your
thumb (A), then move it to the left
(B) until it is released from the
retention tab.
To prevent damage to the socket
pins, do not remove the PnP cap
unless you are installing a CPU.
3.
Slightly lift the load lever in the
direction of the arrow.
4.
Press the right load lever with your
thumb (C), then move it to the right
(D) until it is released from the
retention tab. Lift the load lever in
the direction of the arrow (E).
A
B
Load lever
E
C
D
ASUS Z9PE-D16 Series
2-9
5.
Push the left load lever (F) to lift the
load plate (G).
F
G
6.
Position the CPU over the socket,
ensuring that the triangle mark is on
the top‑right corner of the socket.
Triangle
mark
The CPU fits in only one correct orientation. DO NOT force the CPU into the
socket to prevent bending the connectors on the socket and damaging the CPU!
7.
Remove the PnP cap (H) from the CPU socket and close the load plate (I).
I
H
2-10
Chapter 2: Hardware information
8.
Push down the right load lever (J),
ensuring that the edge of the load
plate is fixed by the lever (K).
K
J
9.
Insert the right load lever under the
retention tab.
10. Push down the left load lever (L),
and then insert the lever under the
retention tab (M).
ASUS Z9PE-D16 Series
L
M
2-11
11. Apply some Thermal Interface
Material to the exposed area of
the CPU that the heatsink will be
in contact with, ensuring that it is
spread in an even thin layer.
Some heatsinks come with preapplied thermal paste. If so, skip
this step.
The Thermal Interface Material is toxic and inedible. DO NOT eat it. If it
gets into your eyes or touches your skin, wash it off immediately, and seek
professional medical help.
12. Connect the CPU fan cable to the connector on the motherboard labeled
CPU_FAN1 / CPU_FAN2.
DO NOT forget to connect the CPU fan connector! Hardware monitoring errors
can occur if you fail to plug this connector.
2-12
Chapter 2: Hardware information
2.4
System memory
2.4.1
Overview
The motherboard comes with eight (per CPU) Double Data Rate 3 (DDR3) Dual
Inline Memory Modules (DIMM) sockets.
A DDR3 module has the same physical dimensions as a DDR2 DIMM but is
notched differently to prevent installation on a DDR2 DIMM socket. DDR3 modules
are developed for better performance with less power consumption.
The figure illustrates the location of the DDR3 DIMM sockets:
2.4.2
Memory Configurations
You may install 2GB, 4GB, 8GB, and 16GB RDIMMs or 2GB, 4GB and 8GB* with
ECC/Non-ECC UDIMMs or 8GB, 16GB and 32GB* LR-DIMMs into the DIMM sockets
using the memory configurations in this section.
1 CPU Configuration (must on CPU1)
DIMM_A2 DIMM_A1 DIMM_B2 DIMM_B1 DIMM_C2 DIMM_C1 DIMM_D2 DIMM_D1
X
1 DIMMs
X
X
2 DIMMs
X
X
X
X
4 DIMMs
X
X
X
X
X
X
X
X
8 DIMMs
•
*Refer to ASUS Server AVL for latest update.
•
Start installing the DIMMs from slot A1 and B1 (light blue).
•
Always install DIMMs with the same CAS latency. For optimum
compatibility, it is recommended that you obtain memory modules from the
same vendor.
ASUS Z9PE-D16 Series
2-13
2 CPU Configuration
DIMM_A2 DIMM_A1 DIMM_B2 DIMM_B1 DIMM_C2 DIMM_C1 DIMM_D2 DIMM_D1
X
1 DIMMs
X
2 DIMMs
X
X
4 DIMMs
X
X
X
X
8 DIMMs
X
X
X
X
X
X
12 DIMMs
X
X
X
X
X
X
X
X
16 DIMMs
2 CPU Configuration
DIMM_E2 DIMM_E1 DIMM_F2 DIMM_F1 DIMM_G2 DIMM_G1 DIMM_H2 DIMM_H1
1 DIMMs
X
2 DIMMs
X
X
4 DIMMs
X
X
X
X
8 DIMMs
X
X
X
X
X
X
12 DIMMs
X
X
X
X
X
X
X
X
16 DIMMs
2-14
Chapter 2: Hardware information
2.4.3
1.
2.
Installing a DIMM on a single clip DIMM socket
Unlock a DIMM socket by pressing
the retaining clip outward.
DIMM notch
Align a DIMM on the socket
such that the notch on the DIMM
matches the DIMM slot key on the
socket.
1
2
DIMM slot key
Unlocked retaining clip
A DIMM is keyed with a notch so that it fits in only one direction. DO NOT force
a DIMM into a socket in the wrong direction to avoid damaging the DIMM.
3.
Hold the DIMM by both of its ends,
then insert the DIMM vertically
into the socket. Apply force to both
ends of the DIMM simultaneously
until the retaining clip snaps back
into place, and the DIMM cannot
be pushed in any further to ensure
proper sitting of the DIMM.
3
Locked Retaining Clip
Always insert the DIMM into the socket VERTICALLY to prevent DIMM notch
damage.
•
To install two or more DIMMs, refer to the user guide bundled in the
motherboard package.
•
Refer to the user guide for qualified vendor lists of the memory modules.
Removing a DIMM from a single clip DIMM socket
1.
2.
Press the retaining clip outward to
unlock the DIMM.
Remove the DIMM from the socket.
2
1
Support the DIMM lightly with your fingers when pressing the retaining clips.
The DIMM might get damaged when it flips out with extra force.
ASUS Z9PE-D16 Series
2-15
2.5
Expansion slots
In the future, you may need to install expansion cards. The following subsections
describe the slots and the expansion cards that they support.
Ensure to unplug the power cord before adding or removing expansion cards.
Failure to do so may cause you physical injury and damage motherboard
components.
2.5.1
Installing an expansion card
To install an expansion card:
1.
2.
3.
4.
5.
6.
Before installing the expansion card, read the documentation that came with
it and make the necessary hardware settings for the card.
Remove the system unit cover (if your motherboard is already installed in a
chassis).
Remove the bracket opposite the slot that you intend to use. Keep the screw
for later use.
Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Secure the card to the chassis with the screw you removed earlier.
Replace the system cover.
2.5.2
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1.
2.
3.
Turn on the system and change the necessary BIOS settings, if any. See
Chapter 4 for information on BIOS setup.
Assign an IRQ to the card. Refer to the tables on the next page.
Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share
IRQ” or that the cards do not need IRQ assignments. Otherwise, conflicts will
arise between the two PCI groups, making the system unstable and the card
inoperable.
2-16
Chapter 2: Hardware information
2.5.3
Interrupt assignments
Standard Interrupt assignments
IRQ
Priority
Standard function
1
2
Keyboard Controller
0
2
3*
4*
5*
6
7*
8
9*
10*
11*
12*
13
14*
15*
1
-
11
12
13
14
15
3
4
5
6
7
8
9
10
System Timer
Programmable Interrupt
Communications Port (COM2)
Communications Port (COM1)
--
Floppy Disk Controller
--
System CMOS/Real Time Clock
ACPI Mode when used
IRQ Holder for PCI Steering
IRQ Holder for PCI Steering
PS/2 Compatible Mouse Port
Numeric Data Processor
Primary IDE Channel
Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2.5.4
PCI Express x16 slot (x16 link)
The onboard PCIE 3 and 5 provide one x16 Gen3 link to CPU2; The onboard PCIE
4 provide one x16 Gen3 link to CPU1; The onboard PCIE 2 provide one x16 Gen3
link to CPU1 (Auto switch to x8 link if PCIE 1 is occupied). These slots support
VGA cards and various server class high performance add-on cards.
2.5.5
PCI Express x16 slot (x8 link)
The onboard PCIE 6 provides one x8 link to CPU2; The onboard PCIE 1 slots
provide one x8 Gen3 link to CPU1 (MIO supported.). These slot supports VGA
Cards and various server class high performance add-on cards.
2.5.6
PIKE slots
The PIKE slot allows you to choose and change your preferred SAS solution easily.
Install an optional ASUS PIKE RAID card based on your needs.
ASUS Z9PE-D16 Series
2-17
PIKE slot (from CPU 1)
PCIE 6 (x8 Gen3 link, Balck, from CPU 2)
PCIE 5 (x16 Gen3 link, Balck, from CPU 2)
PCIE 4 (x16 Gen3 link, White, from CPU 1)
PCIE 3 (x16 Gen3 link, Balck, from CPU 2)
PCIE 2 (x16 Gen3 link, Auto switch to x8 link if PCIE 1 is
occupied, White, from CPU 1)
PCIE 1 (x8 link, Gen3 link, MIO supported, White, from CPU 1)
2-18
Chapter 2: Hardware information
2.5.7
Installing an ASUS PIKE RAID card
Follow the steps below to install an optional ASUS PIKE RAID card on your
motherboard.
1.
Locate the PIKE RAID card slot on the motherboard.
2.
Align the golden fingers of the PIKE RAID card with the PIKE RAID card slot.
ASUS Z9PE-D16 Series
2-19
3.
Insert the PIKE RAID card into the PIKE RAID card slot. Ensure that it is
completely seated on the PIKE RAID card slot.
For details about the installing the SAS HDD for PIKE, please refer to 2.7.2 PSAS
connectors.
2-20
Chapter 2: Hardware information
2.5.8
Installing ASMB6 management board
Follow the steps below to install an optional ASMB6 management board on your
motherboard.
1.
Locate the ASMB6 header on the
motherboard.
2.
Orient and press the ASMB6
management card in place.
ASUS Z9PE-D16 Series
2-21
2.6
1.
Jumpers
Clear RTC RAM (CLRTC1)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS.
You can clear the CMOS memory of date, time, and system setup parameters
by erasing the CMOS RTC RAM data. The onboard button cell battery
powers the RAM data in CMOS, which include system setup information such
as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 1–2 (default) to pins 2–3. Keep the cap
on pins 2–3 for about 5–10 seconds, then move the cap back to pins 1–
2.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS setup
to re-enter data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper
default position. Removing the cap will cause system boot failure!
If the steps above do not help, remove the onboard battery and move the
jumper again to clear the CMOS RTC RAM data. After the CMOS clearance,
reinstall the battery.
2-22
Chapter 2: Hardware information
2.
VGA controller setting (3-pin VGA_SW1)
This jumper allows you to enable or disable the onboard VGA controller. Set
to pins 1–2 to activate the VGA feature.
3.
LAN controller setting (3-pin LAN_SW1)
These jumpers allow you to enable or disable the onboard Intel® I350 Gigabit
LAN controllers. Set to pins 1-2 to activate the Gigabit LAN feature.
ASUS Z9PE-D16 Series
2-23
4.
5.
2-24
LSI MegaRAID or Intel RSTe selection jumper (3-pin RAID_SEL1)
This jumper allows you to select the PCH SATA RAID mode to use LSI
MegaRAID software or Intel® Rapid Storage Technology enterprise 3.0 RAID.
Place the jumper caps over pins 1–2 if you want to use the LSI MegaRAID
software RAID Utility (default); otherwise, place the jumper caps to pins 2–3
to use the Intel® Rapid Storage Technology Enterprise Option ROM Utility.
ME firmware force recovery setting (3-pin ME_RCVR1)
This jumper allows you to force Intel Management Engine (ME) boot from
recovery mode when ME become corrupted.
Chapter 2: Hardware information
6.
7.
DDR3 thermal event setting (3-pin DIMMTRIP1)
This jumper allows you to enable/disable DDR3 DIMM thermal sensing event
pin.
PMBus 1.2 PSU select jumper (3-pin SMART_PSU1)
This jumper allows you to select PSU PMBus version, Set to pins 1-2 for
PMBus, set to pins 2-3 for Others.
ASUS Z9PE-D16 Series
2-25
2.7
Connectors
2.7.1
Rear panel connectors
1
2
3
7
1.
2.
3.
4.
5.
6.
7.
8.
9.
2-26
8
4
5
6
9
PS/2 mouse port (green). This port is for a PS/2 mouse.
DM_LAN 1 (RJ-45) port. This port allows Gigabit connection to a Local Area
Network (LAN) through a network hub for dedicated BMC Mamagement
function. Refer to the table below for the DM_LAN1 and LAN port LED
indications.
LAN 1 (RJ-45) port. This port allows Gigabit connection to a Local Area
Network (LAN) through a network hub. Refer to the table below for the LAN
port LED indications.
LAN 2 (RJ-45) port. This port allows Gigabit connection to a Local Area
Network (LAN) through a network hub. Refer to the table below for the LAN
port LED indications.
LAN 3 (RJ-45) port (Z9PE-D16 only). This port allows Gigabit connection to
a Local Area Network (LAN) through a network hub. Refer to the table below
for the LAN port LED indications.
LAN 4 (RJ-45) port (Z9PE-D16 only). This port allows Gigabit connection to
a Local Area Network (LAN) through a network hub. Refer to the table below
for the LAN port LED indications.
PS/2 keyboard port (purple). This port is for a PS/2 keyboard.
USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports
are available for connecting USB 2.0 devices.
Video Graphics Adapter port. This port is for a VGA monitor or other VGAcompatible devices.
Chapter 2: Hardware information
DM_LAN1 port LED indications
Activity/Link LED
Speed LED
OFF
OFF
Status
Description
Orange
Linked
Blinking
No link
Data activity
ACT/LINK SPEED
LED
LED
Status
Description
Orange
100 Mbps connection
Green
10 Mbps connection
1 Gbps connection
DM LAN port
LAN port LED indications
Activity/Link LED
Speed LED
OFF
OFF
Status
Description
Green
Linked
Blinking
2.7.2
No link
Data activity
Status
Description
Orange
100 Mbps connection
Green
10 Mbps connection
1 Gbps connection
LAN port
Internal connectors
1.
Serial ATA 6.0/3.0 Gb/s connectors
(7-pin SATA6G_1-2 [Blue])
ACT/LINK SPEED
LED
LED
(�������������������������
7-pin SATA3G_������������
3-6 [black])
Supported by the Intel® 602 Chipset, these connectors are for the Serial ATA
signal cables for Serial ATA hard disk drives that allows up to 6Gb/s of data
transfer rate.
If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID 1,
RAID 10, or RAID 5 configuration.
ASUS Z9PE-D16 Series
2-27
2.
SATA connector -- ISAS connectors
Supported by the Intel® C602 PCH. ISAS 1-4 connectors can connect to serial
ATA 3Gb/s hard disk drives.
The actual data transfer rate depends on the speed of SATA hard disks installed.
2-28
Chapter 2: Hardware information
3.
4.
Hard disk activity LED connector (4-pin HDLED1)
This LED connector is for the storage add-on card cable connected to
the SATA or SAS add-on card. The read or write activities of any device
connected to the SATA or SAS add-on card causes the front panel LED to
light up.
SAS connector -- PSAS connectors
SAS connector - PSAS connectors are for the SAS signal cables for SAS
hard disk drives that allows up to 6Gb/s of data transfer rate.
If you installed SAS hard disk drives, you can create a RAID 0, RAID 1, RAID
10, or RAID 5 configuration.
The actual data transfer rate depends on the speed of SAS hard disks installed.
ASUS Z9PE-D16 Series
2-29
5.
2-30
USB connectors (10-1 pin USB34, USB56; A-Type USB10)
These connectors are for USB 2.0 ports. Connect the USB module cables to
connectors USB34 and USB56, then install the modules to a slot opening at
the back of the system chassis. These USB connectors comply with USB 2.0
specification that supports up to 480 Mbps connection speed.
Chapter 2: Hardware information
6.
CPU, front and rear fan connectors
(4-pin CPU_FAN1-2, FRNT_FAN1–4, REAR_FAN1-2)
The fan connectors support cooling fans. Connect the fan cables to the fan
connectors on the motherboard, ensuring that the black wire of each cable
matches the ground pin of the connector.
•
DO NOT forget to connect the fan cables to the fan connectors. Insufficient
air flow inside the system may damage the motherboard components.
•
These are not jumpers! DO NOT place jumper caps on the fan connectors!
•
All fans feature the ASUS Fan Speed Control technology.
ASUS Z9PE-D16 Series
2-31
7.
Serial General Purpose Input/Output connectors
(8-1 pin PSGPIO 1/2, ISGPIO1, SGPIO1)
The SGPIO 1 connectors are used for the Intel Rapid Storage Technology
Enterprise SGPIO interface that controls the LED pattern generation, device
information and general purpose data.
The PSGPIO 1/2 connectors are used for PIKE card.
8.
2-32
Serial port connectors (10-1 pin COM1/COM2)
These connectors are for the serial (COM) ports. Connect the serial port
module cable to one of these connectors, then install the module to a slot
opening at the back of the system chassis.
Chapter 2: Hardware information
9.
TPM connector (20-1 pin TPM)
This connector supports a Trusted Platform Module (TPM) system, which can
securely store keys, digital certificates, passwords, and data. A TPM system
also helps enhance network security, protects digital identities, and ensures
platform integrity.
ASUS Z9PE-D16 Series
2-33
10. EATX power connectors
(24-pin EATXPWR1, 8-pin EATX12V1/EATX12V2, PSUSMB1)
These connectors are for an EATX power supply plugs. The power supply
plugs are designed to fit these connectors in only one orientation. Find the
proper orientation and push down firmly until the connectors completely fit.
2-34
•
DO NOT forget to connect the 24+8+8-pin power plugs; otherwise, the
system will not boot up.
•
Use of a PSU with a higher power output is recommended when configuring
a system with more power-consuming devices. The system may become
unstable or may not boot up if the power is inadequate.
•
This motherboard supports EATX2.0 PSU or later version.
•
Ensure that your power supply unit (PSU) can provide at least the minimum
power required by your system.
Chapter 2: Hardware information
11. System panel connector (20-1 pin PANEL1)
This connector supports several chassis-mounted functions.
(1) System power LED (3-pin PLED)
This 3-pin connector is for the system power LED. Connect the chassis
power LED cable to this connector. The system power LED lights up
when you turn on the system power, and blinks when the system is in
sleep mode.
(2) Message LED (2-pin MLED)
This 2-pin connector is for the message LED cable that connects to
the front message LED. The message LED is controlled by Hardware
monitor to indicate an abnormal event occurance.
(3) System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning
speaker. The speaker allows you to hear system beeps and warnings.
(4) Hard disk drive activity LED (2-pin HDDLED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD
Activity LED cable to this connector. The HDD LED lights up or flashes
when data is read from or written to the HDD.
(5) Power button/soft-off button (2-pin PWRSW)
This connector is for the system power button. Pressing the power
button turns the system on or puts the system in sleep or soft-off mode
depending on the BIOS settings. Pressing the power switch for more
than four seconds while the system is ON turns the system OFF.
(6) Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system
reboot without turning off the system power.
ASUS Z9PE-D16 Series
2-35
12. Auxiliary panel connector (20-2 pin AUX_PANEL1)
This connector is for additional front panel features including front panel
SMB, locator LED and switch, chassis intrusion, and LAN LEDs.
(1) Front panel SMB (6-1 pin FPSMB)
These leads connect the front panel SMBus cable.
(2) LAN activity LED (2-pin LAN13_LED, LAN24_LED)
These leads are for Gigabit LAN activity LEDs on the front panel.
(3) Chassis intrusion (4-1 pin CHASSIS)
These leads are for the intrusion detection feature for chassis with
intrusion sensor or microswitch. When you remove any chassis
component, the sensor triggers and sends a high-level signal to these
leads to record a chassis intrusion event. The default setting is short
CASEOPEN and GND pin by jumper cap to disable the function.
(4) Locator LED (2-pin LOCATORLED1 and 2-pin LOCATORLED2)
These leads are for the locator LED1 and LED2 on the front panel.
Connect the Locator LED cables to these 2-pin connector. The LEDs will
light up when the Locator button is pressed.
(5) Locator Button/Swich (2-pin LOCATORBTN)
These leads are for the locator button on the front panel. This button
queries the state of the system locator.
2-36
Chapter 2: Hardware information
2.8 Internal LEDs
1. DIMM warning LED (ERR_DIMMA1/2; ERR_DIMMB1/2; ERR_DIMMC1/2;
ERR_DIMMD1/2; ERR_DIMME1/2; ERR_DIMMF1/2; ERR DIMMG1/2; ERR
DIMMH1/2)
The DIMM warning LEDs light up to indicate an impending failure of the corresponding
DIMMs.
The warning LEDs function only when you install the ASUS ASMB6.
ASUS Z9PE-D16 Series
2-37
2. BMC LED (BMC_LED1)
The green heartbeat LED blinks per second to indicate that the ASMB6 is working
normally.
•
The heartbeat LED functions only when you install the ASUS ASMB6
•
Everytime after the AC power is replugged, you have to wait for about
30 seconds for the system to power up.
3. CPU warning LED (ERR_CPU1, ERR_CPU2)
The CPU warning LEDs light up to indicate an impending failure of the corresponding
CPU.
The warning LEDs function only when you install the ASUS ASMB6.
2-38
Chapter 2: Hardware information
4. CATT LED
The CATT LED indicates that the system has experienced a fatal or catastrophic error
and cannot continue to operate.
5. Q-Code LEDs
The Q-Code LED provides you a 2-digit display that shows the system status. Refer
to the Q-Code table below for more details.
ASUS Z9PE-D16 Series
2-39
Q-Code table
Action
Normal boot
PHASE
Security Phase
POST CODE
01
TYPE
Progress
DESCRIPTION
First post code(POWER_ON_POST_CODE)
03
Progress
Set cache as ram for PEI phase(CACHE_ENABLED_POST_CODE)
02
06
PEI(Pre-EFI
initialization) phase
04
10
15
19
78~00
A1
A3
A7
A8
A9
AA
AB
AC
AD
AE
AF
2F
B0
B1
AF
B4
B2
B3
B5
B6
B7
B8
B9
BA
BB
BC
BF
5A
31
32
34
36
4F
Progress
Progress
Progress
Progress
Progress
Progress
Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
MRC Progress
Progress
Progress
Progress
Progress
Progress
Load BSP microcode(MICROCODE_POST_CODE)
CPU Early init.(CPU_EARLY_INIT_POST_CODE)
initializes South bridge for PEI preparation
PEI Core Entry
NB initialize before installed memory
SB initialize before installed memory
Wait BMC ready(duration: 120 seconds).
QPI initialization
QPI initialization
QPI initialization
QPI initialization
QPI initialization
QPI initialization
QPI initialization
QPI initialization
QPI initialization
QPI initialization
QPI initialization Complete
Memory Init.
Memory Init.
Memory Init.
RC Reset if require
Memory Init.
Memory Init.
Memory Init.
Memory Init.
Memory Init.
Memory Init.
Memory Init.
Memory Init.
Memory Init.
Memory Init.
Memory Init.
Memory Init. Done
Other config. After RC end
Memory already installed.
CPU Init.
CPU Init.
CPU Init.
DXE Initial Program Load(IPL)
(continued on the next page)
2-40
Chapter 2: Hardware information
Normal boot
DXE(Driver
60
Execution
61
Environment) phase
62
Progress
DXE Core Started
Progress
SB run-time init.
68
Progress
63
69
6A
70
71
72
78
79
BDS(Boot Device 90
Selection) phase
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
b2
b3
b4
b6
b7
A0
A1
A2
A3
A8
A9
AB
AD
AE
Operating system 17
phase
18
19
20
21
22
23
24
25
ASUS Z9PE-D16 Series
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
Progress
DXE NVRAM Init.
DXE CPU Init
NB Init.
NB Init.
NB Init.
SB Init.
SB Init.
SB Init.
ACPI Init.
CSM Init.
BDS started
Connect device event
PCI Bus Enumeration.
PCI Bus Enumeration.
PCI Bus Enumeration.
PCI Bus Enumeration.
PCI Bus Enumeration.
Console outout connect event
Console input connect event
AMI Super IO start
AMI USB Driver Init.
AMI USB Driver Init.
AMI USB Driver Init.
AMI USB Driver Init.
Legacy Option ROM Init.
Reset system
USB hotplug
NVRAM clean up
NVRAM configuration reset
IDE, AHCI Init.
IDE, AHCI Init.
IDE, AHCI Init.
IDE, AHCI Init.
BIOS Setup Utility password verify
BIOS Setup Utility start
BIOS Setup Utility input wait
Ready to boot event
Legacy boot event
ME event for Node Manager
ME event for Node Manager
ME event for Node Manager
ME event for Node Manager
ME event for Node Manager
ME event for Node Manager
ME event for Node Manager
ME event for Node Manager
ME event for Node Manager
2-41
2-42
Chapter 2: Hardware information
This chapter describes the power up
sequence, and ways of shutting down the
system.
Chapter 3:
3
Powering up
Chapter summary
3.1
3.2
3
Starting up for the first time......................................................... 3-3
Powering off the computer........................................................... 3-4
ASUS Z9PE-D16 Series
3.1
Starting up for the first time
1.
After making all the connections, replace the system case cover.
2.
Be sure that all switches are off.
3.
Connect the power cord to the power connector at the back of the system
chassis.
4.
Connect the power to a power outlet that is equipped with a surge protector.
5.
Turn on the devices in the following order:
b. External storage devices (starting with the last device on the chain)
6.
7.
a. Monitor
c. System power
After applying power, the system power LED on the system front panel case
lights up. For systems with ATX power supplies, the system LED lights up
when you press the ATX power button. If your monitor complies with “green”
standards or if it has a “power standby” feature, the monitor LED may light up
or switch between orange and green after the system LED turns on.
The system then runs the power-on self-test or POST. While the tests are
running, the BIOS beeps or additional messages appear on the screen. If you
do not see anything within 30 seconds from the time you turned on the power,
the system may have failed a power-on test. Check the jumper settings and
connections or call your retailer for assistance.
At power on, hold down the <Del> key to enter the BIOS Setup. Follow the
instructions in Chapter 4.
ASUS Z9PE-D16 Series
3-3
3.2
Powering off the computer
3.2.1
Using the OS shut down function
If you are using Windows® 2008 Server:
1. Click the Start button, move the cursor to the triangle on the right of Log off,
and then click Shut Down.
2. From the Shutdown Event Tracker, select the option that best describes
why you want to shut down the computer.
3.
Ensure that the Planned check box is checked.
4.
If necessary, key in comments.
5.
Click OK.
3.2.2
Using the dual function power switch
While the system is ON, pressing the power switch for less than four seconds puts
the system to sleep mode or to soft-off mode, depending on the BIOS setting.
3-4
Chapter 3: Powering up
This chapter tells you how to change the
system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS
parameters are also provided.
Chapter 4:
4
BIOS setup
Chapter summary
4
4.1
Managing and updating your BIOS............................................. 4-3
4.3
Main menu................................................................................... 4-10
4.2
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
BIOS setup program..................................................................... 4-7
Advanced menu.......................................................................... 4-11
Server Mgmt menu...................................................................... 4-37
Event Logs menu........................................................................ 4-40
Boot menu................................................................................... 4-42
Monitor menu.............................................................................. 4-44
Security menu............................................................................. 4-45
Tool menu.................................................................................... 4-47
Exit menu..................................................................................... 4-47
ASUS Z9PE-D16 Series
4.1
Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard Basic
Input/Output System (BIOS) setup:
1.
2.
3.
ASUS CrashFree BIOS 3 (Recovers the BIOS using a bootable USB flash
disk drive when the BIOS file fails or gets corrupted.)
ASUS EZ Flash 2 (Updates the BIOS using a USB flash disk.)
BUPDATER utility (Updates the BIOS in DOS mode using a bootable USB
flash disk drive.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable USB flash
disk drive in case you need to restore the BIOS in the future. Copy the original
motherboard BIOS using the BUPDATER utility.
4.1.1
ASUS CrashFree BIOS 3 utility
The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore
the BIOS file when it fails or gets corrupted during the updating process. You can
update a corrupted BIOS file using a USB flash drive that contains the updated
BIOS file.
Prepare a USB flash drive containing the updated motherboard BIOS before
using this utility.
Recovering the BIOS from a USB flash drive
To recover the BIOS from a USB flash drive:
1.
2.
Insert the USB flash drive with the original or updated BIOS file to one USB
port on the system.
The utility will automatically recover the BIOS. It resets the system when the
BIOS recovery is finished.
DO NOT shut down or reset the system while recovering the BIOS! Doing so
would cause system boot failure!
The recovered BIOS may not be the latest BIOS version for this motherboard.
Visit the ASUS website at www.asus.com to download the latest BIOS file.
ASUS Z9PE-D16 Series
4-3
4.1.2
ASUS EZ Flash 2 Utility
The ASUS EZ Flash 2 Utility feature allows you to update the BIOS without having
to use a DOS‑based utility.
Before you start using this utility, download the latest BIOS from the ASUS
website at www.asus.com.
To update the BIOS using EZ Flash 2 Utility
1.
2.
Insert the USB flash disk that contains the latest BIOS file into the USB port.
Enter the BIOS setup program. Go to the Tool menu then select ASUS EZ
Flash 2 Utility. Press <Enter>.
Exit
ASUSTek EZ Flash 2 Utility V01.04
Flash Info
MODEL: Z9PE-D16
VER: 0208
DATE: 10/18/2011
fs0:\
Drive
Folder Info
fs0:\
fs1:\
12/09/10
10:23p
4194304
Z9PE-D16.ROM
File Infor
MODEL:
VER:
DATE:
Help Info
[Enter] Select or Load
3.
4.
5.
6.
4-4
[Tab] Switch
[Up/Down/PageUp/PageDown/Home/End] Move
[Esc] Exit
[F2] Backup
Press <Tab> to switch to the Drive field.
Press the Up/Down arrow keys to find the USB flash disk that contains the
latest BIOS, then press <Enter>.
Press <Tab> to switch to the Folder Info field.
Press the Up/Down arrow keys to find the BIOS file, and then press <Enter>
to perform the BIOS update process. Reboot the system when the update
process is done.
Chapter 4: BIOS setup
•
This function can support devices such as a USB flash disk with FAT 32/16
format and single partition only.
•
DO NOT shut down or reset the system while updating the BIOS to prevent
system boot failure!
Ensure to load the BIOS default settings to ensure system compatibility and
stability. Press <F5> and select Yes to load the BIOS default settings.
4.1.3
BUPDATER utility
The succeeding BIOS screens are for reference only. The actual BIOS screen
displays may not be the same as shown.
The BUPDATER utility allows you to update the BIOS file in the DOS environment
using a bootable USB flash disk drive with the updated BIOS file.
Updating the BIOS file
To update the BIOS file using the BUPDATER utility:
1.
2.
3.
Visit the ASUS website at www.asus.com and download the latest BIOS file
for the motherboard. Save the BIOS file to a bootable USB flash disk drive.
Copy the BUPDATER utility (BUPDATER.exe) from the ASUS support
website at support.asus.com to the bootable USB flash disk drive you created
earlier.
Boot the system in DOS mode, then at the prompt, type:
BUPDATER /i[filename].ROM
where [filename] is the latest or the original BIOS file on the bootable USB
flash disk drive, then press <Enter>.
A:\>BUPDATER /i[file name].ROM
ASUS Z9PE-D16 Series
4-5
4.
The utility verifies the file, then starts updating the BIOS file.
ASUSTek BIOS Update for DOS V1.30 (11/08/04)
FLASH TYPE: MXIC 25L1605A
Current ROM
BOARD: Z9PE-D16
VER: 0203
DATE: 08/24/2011
Update ROM
BOARD: Z9PE-D16
VER: 0206
DATE: 09/30/2011
PATH: WARNING! Do not turn off power during flash BIOS
Note
Writing BIOS:
DO NOT shut down or reset the system while updating the BIOS to prevent
system boot failure!
5.
The utility returns to the DOS prompt after the BIOS update process is
completed. Reboot the system from the hard disk drive.
The BIOS update is finished! Please restart your system.
C:\>
4-6
Chapter 4: BIOS setup
4.2
BIOS setup program
This motherboard supports a programmable firmware chip that you can update
using the provided utility described in section 5.1 Managing and updating your
BIOS.
Use the BIOS Setup program when you are installing a motherboard, reconfiguring
your system, or prompted to “Run Setup.” This section explains how to configure
your system using this utility.
Even if you are not prompted to use the Setup program, you can change the
configuration of your computer in the future. For example, you can enable the
security password feature or change the power management settings. This
requires you to reconfigure your system using the BIOS Setup program so that the
computer can recognize these changes and record them in the CMOS RAM of the
firmware chip.
The firmware chip on the motherboard stores the Setup utility. When you start up
the computer, the system provides you with the opportunity to run this program.
Press <Del> during the Power-On Self-Test (POST) to enter the Setup utility;
otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing
<Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis. You can
also restart by turning the system off and then back on. Do this last option only if
the first two failed.
The Setup program is designed to make it as easy to use as possible. Being a
menu-driven program, it lets you scroll through the various sub-menus and make
your selections from the available options using the navigation keys.
•
The default BIOS settings for this motherboard apply for most conditions
to ensure optimum performance. If the system becomes unstable after
changing any BIOS settings, load the default settings to ensure system
compatibility and stability. Press <F5> and select Yes to load the BIOS
default settings.
•
The BIOS setup screens shown in this section are for reference purposes
only, and may not exactly match what you see on your screen.
•
Visit the ASUS website (www.asus.com) to download the latest BIOS file for
this motherboard.
ASUS Z9PE-D16 Series
4-7
4.2.1
BIOS menu screen
Menu items
Main
Menu bar
Configuration fields
General help
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Server Mgmt Event Logs Boot Monitor Security Tool Exit
BIOS Information
BIOS Vendor
Core Version
Compliancy
BIOS Version
Build Date
American Megatrends
4.6.4.1
UEFI 2.1; PI 0.9
0306 x64
01/16/2012
System Date
System Time
[Tue 01/17/2012]
[15:07:28]
Access Level
Administrator
Memory Information
Total Memory
2048 MB (DDR3)
Processor
CPU Speed
Count:
2600 MHz
1
Onboard
Onboard
Onboard
Onboard
LAN1
LAN2
LAN3
LAN4
MAC
MAC
MAC
MAC
00:E0:18:10:14:00
00:E0:18:10:14:01
00:E0:18:10:14:02
00:E0:18:10:14:03
Set the Date, Use Tab to
switch between Data elements.
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Navigation keys
4.2.2
Menu bar
The menu bar on top of the screen has the following main items:
Main
For changing the basic system configuration
Server Mgmt
For changing the Server Mgmt settings
Advanced
Event Logs
For changing the advanced system settings
For changing the event log settings
MonitorFor displaying the system temperature, power status, and
changing the fan settings
Security For changing the security settings
Tool
For configuring options for special functions
Boot
Exit
For changing the system boot configuration
For selecting the exit options
To select an item on the menu bar, press the right or left arrow key on the keyboard
until the desired item is highlighted.
4-8
Chapter 4: BIOS setup
4.2.3
Menu items
The highlighted item on the menu bar displays the specific items for that menu. For
example, selecting Main shows the Main menu items.
The other items (Event Logs, Advanced, Monitor, Boot, Tool, and Exit) on the menu
bar have their respective menu items.
4.2.4
Submenu items
A solid triangle before each item on any menu screen means that the item has a
submenu. To display the submenu, select the item then press <Enter>.
4.2.5
Navigation keys
At the bottom right corner of a menu screen are the navigation keys for the BIOS
setup program. Use the navigation keys to select items in the menu and change
the settings.
4.2.6
General help
At the top right corner of the menu screen is a brief description of the selected item.
4.2.7
Configuration fields
These fields show the values for the menu items. If an item is user-configurable,
you can change the value of the field opposite the item. You cannot select an item
that is not user-configurable.
A configurable field is enclosed in brackets, and is highlighted when selected. To
change the value of a field, select it and press <Enter> to display a list of options.
4.2.8
Pop-up window
Select a menu item and press <Enter> to display a pop-up window with the
configuration options for that item.
4.2.9
Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that
do not fit on the screen. Press the Up/Down arrow keys or <Page Up> /<Page
Down> keys to display the other items on the screen.
ASUS Z9PE-D16 Series
4-9
4.3
Main menu
When you enter the BIOS Setup program, the Main menu screen appears. The
Main menu provides you an overview of the basic system information, and allows
you to set the system date, time, language, and security settings.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Server Mgmt Event Logs Boot Monitor Security Tool Exit
BIOS Information
BIOS Vendor
Core Version
Compliancy
BIOS Version
Build Date
American Megatrends
4.6.4.1
UEFI 2.1; PI 0.9
0306 x64
01/16/2012
System Date
System Time
[Tue 01/17/2012]
[15:07:28]
Access Level
Administrator
Memory Information
Total Memory
2048 MB (DDR3)
Processor
CPU Speed
Count:
2600 MHz
1
Onboard
Onboard
Onboard
Onboard
LAN1
LAN2
LAN3
LAN4
MAC
MAC
MAC
MAC
00:E0:18:10:14:00
00:E0:18:10:14:01
00:E0:18:10:14:02
00:E0:18:10:14:03
Set the Date, Use Tab to
switch between Data elements.
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
4.3.1
System Date [Day xx/xx/xxxx]
4.3.2
System Time [xx:xx:xx]
Allows you to set the system date.
Allows you to set the system time.
4-10
Chapter 4: BIOS setup
4.4
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other
system devices.
Take caution when changing the settings of the Advanced menu items. Incorrect
field values can cause the system to malfunction.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Server Mgmt Event Logs Boot Monitor Security Tool Exit
CPU Configuration Parameters
CPU Configuration
CPU Power Management Configuration
Chipset Configuration
PCH SATA Configuration
PCH SCU Configuration
PCI Subsystem Setting
Onboard LAN Configuration
Intel TXT(LT-SX) Configuration
USB Configuration
Trusted Computing
ACPI Settings
WHEA Configuration
APM
Serial Port Console Redirection
ME Subsystem
Legacy Devices Configuration
Runtime Error Logging
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
4.4.1
CPU Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
CPU Confguration
Enter to view socket soecific
CPU Information.
Socket 1 CPU Information
Socket 2
Not Present
CPU Speed
64-bit
2600 MHz
Supported
Hyper Threading
Active Processor Core
Limit CPUID Maximum
Execute Diable Bit
Server Class
Hardware Prefetcher
Adjacent Cache Line Prefetch
DCU Streamer Prefetcher
DCU IP Prefetcher
Intel Virtualization Technologu
Local APIC Mode
[Enabled]
[All]
[Disabled]
[Enabled]
[Custom]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Auto]
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
ASUS Z9PE-D16 Series
4-11
Socket 1 CPU Information
Enter to view socket specific CPU Information.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Enter to view socket soecific
CPU Information.
Socket 1 CPU Information
Genuine Intel(R) CPU @ 2.60GHz
CPU Signature
Microcode Patch
Max CPU Speed
Min CPU Speed
Processor Cores
Intel HT Technology
Intel VT-X Technology
206d5
512
2600 MHz
1200 MHz
8
Supported
Supported
L1
L1
L2
L3
32 kB x8
32 kB x8
256 kB x8
20480 kB
Data Cache
Code Cache
Cache
Cache
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Hyper Threading [Enabled]
Allows you to enable or disable the �����
Intel® Hyper-Threading Technology function.
When disabled, only one thread per activated core is enabled.
Configuration options: [Disabled] [Enabled]
Active Processor Cores [All]
Configuration options: [All] [1] [2] [3] [4] [5] [6] [7]
Limit CPUID Maximum [Disabled]
Setting this item to [Enabled] allows legacy operating system to boot even without
support for CPUs with extended CPUID functions.
Configuration options: [Disabled] [Enabled]
Execute Disable Bit [Enabled]
XD can prevent certain classes of malicious buffer overflow attacks when combined
with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux
9.2, Redhat Enterprise 3 Update 3).
Configuration options: [Disabled] [Enabled]
Server Class [Custom]
Use Intel® recommended prefetch settings.
Configuration options: [Enterprise] [High Performance(HPC)] [Custom]
Hardware Prefetcher [Enabled]
This Item allows you to turn on/off the mid level cache(L2) streamer prefetcher.
Configuration options: [Disabled] [Enabled]
4-12
Chapter 4: BIOS setup
Adjacent Cache Line Prefetch [Enabled]
This Item allows you to turn on/off prefetching of adjacent cache lines.
Configuration options: [Disabled] [Enabled]
DCU Streamer Prefetcher [Enabled]
This Item allows you to enable or disable prefetcher of next L1 data line.
Configuration options: [Disabled] [Enabled]
DCU IP Prefetcher [Enabled]
This Item allows you to enable or disable prefetch of next L1 line based upon
sequential load history.
Configuration options: [Disabled] [Enabled]
Intel® Virtualization Technology [Enabled]
When this item is enabled, a VMM can utilize the additional hardware capabilities
provided by Vanderpool Technology.
Configuration options: [Disabled] [Enabled]
Local APIC Mode [Disabled]
Select Local APIC mode. If Auto, use x2APIC if required. Otherwise, use xAPIC
mode. xAPIC will disable CPUs with APIC IDs greater than 254. Some OS do not
support x2APIC mode.
Configuration options: [Disabled] [Enabled]
ASUS Z9PE-D16 Series
4-13
4.4.2
CPU Power Management Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
CPU Power Management Confguration
This item allows you to
enabled power management
features.
Power Technology [Custom]
EIST [Enabled]
Turbo Mode [Enabled]
P-STATE Coordination [HW_ALL]
CPU C3 Report [Disabled]
CPU C6 Report [Enabled]
CPU C7 Report [Disabled]
Package C State limit [C6]
Energy Performance [Balanced Performance]
Factory long duration power limit
115 Watts
Long duration power limit
0
Factory long duration maintained
1000 ms
→←: Select Screen
Long duration power limit
0
Recommended short duration power1 1.2 * Long Duration ↑↓: Select Item
Enter: Select Item
Short duration power limit
0
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Power Technology [Custom]
This item allows you to enable power management features.
Configuration options: [Disabled] [Energy Efficient] [Custom]
EIST [Enabled]
This item allows you to enable/disable Intel® SpeedStep.
Configuration options: [Disabled] [Enabled]
Turbo Mode [Enabled]
Configuration options: [Disabled] [Enabled]
P-STATE Coordination [HW_ALL]
This item allows you to change P-STATE Coordination type.
Configuration options: [HW_ALL] [SW_ALL] [SW_ANY]
CPU C3 Report [Disabled]
This item allows you to enable/disable CPU C3(ACPI C2) report.
Configuration options: [Disabled] [Enabled]
CPU C6 Report [Enabled]
This item allows you to enable/disable CPU C6(ACPI C3) report.
Configuration options: [Disabled] [Enabled]
4-14
Chapter 4: BIOS setup
CPU C7 Report [Disabled]
This item allows you to enable/disable CPU C7(ACPI C3) report.
Configuration options: [Disabled] [Enabled]
Package C State limit [C6]
This item allows you to set package C State limit.
Configuration options: [C0] [C2] [C6] [C7] [No Limit]
Energy Performance [Balanced Performance]
This item allows you to optimize between performance and power savings.
Windows 2008 and later operating systems override this value according to this
power plan.
Configuration options: [Performance] [Balanced Performance] [Balanced Energy]
[Energy Efficient]
Factory long duration power limit
Long duration power limit
0
115 Watts
Factory long duration maintained
Long duration power limit
0
1000 ms
Recommended short duration power limitation
1.2 * Long Duration
Allows you to set long duration power limit in watts. Use the number keys to set the
value.
Allows you to set time window which the long duration power is maintained. Use
the number keys to set the value.
Short duration power limit
0
Allows you to set short duration power limit in watts. Use the number keys to set
the value.
ASUS Z9PE-D16 Series
4-15
4.4.3
Chipset Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
QPI Configuration
Memory Configuration
CPU II0 Bridge Configuration
PCH Configuration
Intel(R) VT for Directed I/O Configuration
QPI Configuration Page
QPI Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Current QPI Link Speed
Current QPI Link Freq
Isoc
QPI Link Speed Mode
QPI Link Frequency Select
QPI Link0s
QPI Link0p
QPI Link1 Slow
Unknown
[Enabled]
[Fast]
[Auto]
[Disabled]
[Disabled]
[Enabled]
Enable/disable Isoc
Isoc [Enabled]
Configuration options: [Disabled] [Enabled]
QPI Link Speed Mode [Fast]
This item allows you to select the QPI link speed as either the fast mode or slow
mode.
Configuration options: [Slow] [Fast]
QPI Link Frequency Select [Auto]
This item allows for selecting the QPI link frequency
Configuration options: [Auto] [6.4 GT/s] [7.2 GT/s (Fast Mode Only)] [8.0 GT/s
(Fast Mode Only)]
QPI Link0s [Disabled]
Configuration options: [Disabled] [Enabled]
QPI Link0p [Disabled]
Configuration options: [Disabled] [Enabled]
QPI Link1 [Enabled]
Configuration options: [Disabled] [Enabled]
4-16
Chapter 4: BIOS setup
Memory Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Compatibility RID
[Enabled]
Memory Configuration
Total Memory
Current Memory Mode
Currently Memory Speed
Mirroring
Sparing
Memory Mode
DDR Speed
Channel Interleaving
Rank Interleaving
Patrol Scrub
Demand Scrub
Data Scrambling
Device Tagging
Thermal Throtting
�������������
OLTT Peak BW %
����
Enable High Temp
Allow 2x Refresh
Altitude
Memory HOT Sensor support
DIMM Information
2048 MB (DDR3)
Independent
1333 MHz
Supported
Not Possible
[Independent]
[Auto]
[Auto]
[Auto]
[Disabled]
[Enabled]
[Enabled]
[Disabled]
[CLTT]
��
50
[Disabled]
[Enabled]
[300 M]
[Enabled]
Support for compatibility
Revision ID(CRID)
Functionality mentioned in
Sandybridge bios spec.
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Compatibility RID [Enabled]
Support for compatibility revision ID (CRID) functionality mentioned in Sandybridge
BIOS spec. Configuration options: [Enabled] [Disabled]
Memory Mode [Independent]
Select the mode for memory initializaton.
Configuration options: [Independent] [Mirroring] [Lock Step] [Sparing]
DDR Speed [Auto]
Force DDR speed.
Configuration options: [Auto] [Force DDR3 800] [Force DDR3 1066] [Force DDR3
1333] [Force DDR3 1600] [Force DDR3 1866]
Channel Interleaving [Auto]
Select different channel interleaving setting.
Configuration options: [Auto] [1 Way] [2 Way] [3 Way] [4 Way]
Rank Interleaving [Auto]
Select different rank interleaving setting.
Configuration options: [Auto] [1 Way] [2 Way] [4 Way] [8 Way]
ASUS Z9PE-D16 Series
4-17
Patrol Scrub [Disabled]
Allows you to enable/disable Patrol Scrub.
Configuration options: [Disabled] [Enabled]
Demand Scrub [Enabled]
Allows you to enable/disable demand scrubing feature.
Configuration options: [Enabled] [Disabled]
Data Scrambling [Enabled]
Allows you to enable/disable data scrambling.
Configuration options: [Enabled] [Disabled]
Device Tagging [Disabled]
Allows you to enable/disable device tagging.
Configuration options: [Enabled] [Disabled]
Thermal Throtting [CLTT]
Configuration options: [Disabled] [OLTT] [CLTT]
Enable High Temp [Disabled]
Configuration options: [Disabled] [Enabled]
Allow 2x Refresh [Enabled]
Configuration options: [Disabled] [Enabled]
Altitude [300 M]
The system altitude above the sea level in meters.
Configuration options: [Auto] [300 M] [900 M] [1500 M] [3000 M]
Memory Hot sensor support [Enabled]
Configuration options: [Disabled] [Enabled]
4-18
Chapter 4: BIOS setup
DIMM Information
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
CPU1 DIMM Information
Node
Node
Node
Node
Node
Node
Node
Node
0
0
0
0
0
0
0
0
Ch0
Ch0
Ch1
Ch1
Ch2
Ch2
Ch3
Ch3
Dimm
Dimm
Dimm
Dimm
Dimm
Dimm
Dimm
Dimm
A1
A2
B1
B2
C1
C2
D1
D2
Present 2048 MB(DDR3)
Not Present
Not Present
Not Present
Not Present
Not Present
Not Present
Not Present
CPU2 DIMM Information
CPU IIO Bridge Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel(R) I/OAT
DCA Support
VGA Priority
TargetVGA
[Disabled]
[Enabled]
[Offboard]
VGA From CPU 0
Enables/Disables Intel(R)
I/O Acceleration Technology
(I/OAT).
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Intel(R) I/OAT [Disabled]
Allows you to enable or disable Intel® I/O accelaration technology.
Configuration options: [Disabled] [Enabled]
DCA Support [Enabled]
Allows you to enable or disable the direct cache access support.
Configuration options: [Disabled] [Enabled]]
VGA Priority [offboard]
Allows you to prioritize between onboard and 1st offboard video device found.
Configuration options: [Onboard] [Offboard]
ASUS Z9PE-D16 Series
4-19
PCH Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Name
Stepping
Support for PCH Compatibility
Patsburg
05 (C0 Stepping) Revision ID(CRID)
functionality.
SB Chipset Configuration
PCH Compatibility RID [Disabled]
Deep Sx SCU devices Onboard SATA RAID Oprom [Disabled]
[Enabled]
[Enabled]
Audio Configuration
Azalia HD Audio [Enabled]
High Precision Event Timer Configuration
High Precision Timer [Enabled]
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
PCH Compatibility RID [Disabled]
Support for PCH compatibility.
Configuration options: [Disabled] [Enabled]
Deep Sx [Disabled]
Configuration options: [Disabled] [Enabled in S5] [Enabled in S4 and S5]
Mobile platforms support deep S4/S5 in DC only and desktop platforms support
deep S4/S5 in AC only.
SCU devices [Enabled]
Allows you to enable or disable Patsburg SCU devices.
Configuration options: [Enabled] [Disabled]
Onboard SATA RAID Oprom [Enabled]
Allows you to enable/disable onboard SATA RAID option rom if Launch Storage
Oprom is enabled.
Configuration options: [Disabled] [Enabled]
Audio Configuration
Azalia HD Audio [Enabled]
Allows you to enable/disable Azalia HD Audio.
Configuration options: [Disabled] [Enabled]
4-20
Chapter 4: BIOS setup
High Precision Event Timer Configuration
High Precision Timer [Enabled]
Allows you to enable/disable High Precision Event Timer.
Configuration options: [Disabled] [Enabled]
Intel(R) VT for Directed I/O Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel(R) VT-d [Disabled]
Allows you to enable or
disable BIOS ACPI Auto
Configuration.
Intel(R) VT-d [Disabled]
Allows you to enable or disable Intel® VT-d.
Configuration options: [Enabled] [Disabled]
The following item appears only when you set Intel(R) VT-d to [Enabled].
Coherency Support [Disabled]
Allows you to enable/disable VT-d Engine Coherency support.
Configuration options: [Disabled] [Enabled]
ATS Support [Disabled]
Allows you to enable/disable VT-d Engine address translation services (ATS)
support. Configuration options: [Disabled] [Enabled]
4.4.4
PCH SATA Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
SATA
SATA
SATA
SATA
SATA
SATA
Port1
Port2
Port3
Port4
Port5
Port6
Not Present
ASUS DWR ATAPI
WDC WD800JD(80.0GB)
Not Present
Not Present
Not Present
SATA Mode SATA Controller 1
SATA Controller 2
S.M.A.R.T. Status Check [AHCI Mode]
[Enhanced]
[Enhanced]
[Enabled]
Port
Port
Port
Port
Port
Port
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
1
2
3
4
5
6
Staggered
Staggered
Staggered
Staggered
Staggered
Staggered
Spin-up
Spin-up
Spin-up
Spin-up
Spin-up
Spin-up
(1)IDE Mode. (2)AHCI Mode.
(3)RAID Mode.
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
ASUS Z9PE-D16 Series
4-21
SATA Mode [AHCI Mode]
Allows you to set the SATA configuration.
Configuration options: [Disabled] [IDE Mode] [AHCI Mode] [RAID Mode]
•
If you want to use the Serial ATA hard disk drives as Parallel ATA physical
storage devices, set this item to [IDE Mode].
•
If you want the Serial ATA hard disk drives to use the Advanced Host
Controller Interface (AHCI), keep the default setting [AHCI Mode]. The AHCI
allows the onboard storage driver to enable advanced Serial ATA features
that increases storage performance on random workloads by allowing the
drive to internally optimize the order of commands.
•
If you want to create RAID sets with LSI MegaRAID utility, or Intel® Rapid
Storage Technology Enterprise from the Serial ATA hard disk drives, set this
item to [RAID Mode].
SATA Controller 1 [Enhanced]
This item appears only when you set the SATA Mode item to [IDE Mode]. Set to
[Enhanced] to support two SATA 6.0 Gb/s and two SATA 3.0 Gb/s devices. Set to
[Compatible] when using Windows 98/NT/2000/MS-DOS. Up to four SATA devices
are supported under these operating systems.
Configuration options: [Disabled] [Enhanced] [Compatible]
SATA Controller 2 [Enhanced]
This item appears only when you set the SATA Mode item to [IDE Mode]. Set to
[Enhanced] to support two SATA 3.0 Gb/s devices.
Configuration options: [Disabled] [Enhanced]
S.M.A.R.T. Status Check [Enabled]
S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitor
system. When read/write of your hard disk errors occur, this feature allows the hard
disk to report warning messages during the POST.
Configuration options: [Enabled] [Disabled]
Staggered Spin-up [Disabled]
Staggered spin-up is a feature defined in the Serial ATA Specifications. It enables
an HBA to individually spin-up attached SATA devices to avoid maximum current
charged by applying all attached SATA devices at the same time.
Configuration options: [Disabled] [Enabled]
4-22
Chapter 4: BIOS setup
4.4.5
PCH SCU Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Device1
Device2
Device3
Device4
Device5
Device6
Device7
Device8
Sata only RAID5
Intel ISR10a
Intel ISR10a
Intel ISR10a
Intel ISR10a
Intel ISR10a
Intel ISR10a
Intel ISR10a
Intel ISR10a
[Disabled]
Patsburg B/D sku only
Sata only RAID5
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
4.4.6
PCI Subsystem Settings
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
PCI Bus Driver Version
PCI Option ROM Handling
PCI ROM Priority V 2.05.00
[EFI Compatible ROM]
In case of multiple Option
ROMs (Legacy and EFI
Compatible), specifies what
PCI option ROM to lanuch.
PCI 64bit Resources Handling
Above 4G Decoding [Disabled]
PCI Common Setting
PCI Latency Timer VGA Palette Snoop PERR# Generation SERR# Generation Load RT32 Image
[32 PCI Bus Clocks]
[Disabled]
[Disabled]
[Disabled]
[Enabled]
PCI Express Settings
PCIE Slot Option Rom Configuration
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
PCI ROM Priority [EFI Compatible ROM]
In case of multiple option roms (Legacy and EFI Compatible), specifies what PCI
option rom to launch.Configuration options: [Legacy ROM] [EFI Compatible ROM]
PCI Latency Timer [32 PCI Bus Clocks]
Value to be programmed into PCI latency timer register
Configuration options: [32 PCI Bus Clocks] [64 PCI Bus Clocks] [96 PCI Bus
Clocks] [128 PCI Bus Clocks] [160 PCI Bus Clocks] [192 PCI Bus Clocks] [224 PCI
Bus Clocks] [248 PCI Bus Clocks]
ASUS Z9PE-D16 Series
4-23
VGA Palette Snoop [Disabled]
Allows you to enable or disable VGA pallette registers snooping.
Configuration options: [Disabled] [Enabled]
PERR# Generation [Disabled]
Allows you to enable or disable PCI device to generate PERR#.
Configuration options: [Disabled] [Enabled]
SERR# Generation [Disabled]
Allows you to enable or disable PCI device to generate SERR#.
Configuration options: [Disabled] [Enabled]
Load RT32 Image [Enabled]
Allows you to enable or disable RT32 Image Loading.
Configuration options: [Disabled] [Enabled]
PCI Express Settings
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
PCI Express Link Register Settings
ASPM Support [Disabled]
WARNING: Enabling ASPM may cause
PCI-E device to fail
some
Allows you to enable or
disablePCI Express Device
Relaxed Ordering.
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
PCI Express Link Register Settings
ASPM Support [Disabled]
Allows you to set the ASPM level. Configuration options: [Disabled] [Auto] [Force
L0s]
[Force L0s] Force all links to L0s state.
[Auto]
BIOS auto configure.
[Disabled]
Disabled ASPM.
4-24
Chapter 4: BIOS setup
PCIE Slot Option Rom Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Legacy OpROM Support
Launch Storage 0pROM [Enabled]
PCIE1 Option Rom
PCIE2 Option Rom
PCIE3 Option Rom
PCIE4 Option Rom
PCIE5 Option Rom
PCIE6 Option Rom
PIKE Option Rom
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
Allows you to enable
or disable boot option
for legacy mass storage
device with option ROM.
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Launch Storage OpROM [Enabled]
Allows you to enable or disable boot option for legacy mass storage device with
option ROM.
Configuration options: [Disabled] [Enabled]
PCIE1 Option Rom [Enabled]
Configuration options: [Disabled] [Enabled]
PCIE2 Option Rom [Enabled]
Configuration options: [Disabled] [Enabled]
PCIE3 Option Rom [Enabled]
Configuration options: [Disabled] [Enabled]
PCIE4 Option Rom [Enabled]
Configuration options: [Disabled] [Enabled]
PCIE5 Option Rom [Enabled]
Configuration options: [Disabled] [Enabled]
PCIE6 Option Rom [Enabled]
Configuration options: [Disabled] [Enabled]
PIKE Option Rom [Enabled]
Configuration options: [Disabled] [Enabled]
ASUS Z9PE-D16 Series
4-25
4.4.7
Onboard LAN Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
PXE/iSCSI.
Onboard LAN Configuration
Intel LAN ROM Type Intel LAN1 Enable LAN1 Option ROM Support Intel LAN2 Enable LAN2 Option ROM Support Intel LAN3 Enable LAN3 Option ROM Support Intel LAN4 Enable LAN4 Option ROM Support [PXE]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Intel LAN ROM Type [PXE]
Configuration options: [PXE] [iSCSI]
The following item appears only when you set Intel LAN Support to [Enabled].
Intel LAN1 Enable [Enabled]
Allows you to enable or disable Intel® LAN1 function. Configuration options:
[Disabled] [Enabled]
LAN1 Option ROM Support [Enabled]
Configuration options: [Disabled] [Enabled]
Intel LAN2 Enable [Enabled]
Allows you to enable or disable Intel® LAN2 function. Configuration options:
[Disabled] [Enabled]
LAN2 Option ROM Support [Enabled]
Configuration options: [Disabled] [Enabled]
Intel LAN3 Enable [Enabled] (Z9PE-D16 only)
Allows you to enable or disable Intel® LAN3 function. Configuration options:
[Disabled] [Enabled]
LAN3 Option ROM Support [Enabled] (Z9PE-D16 only)
Configuration options: [Disabled] [Enabled]
4-26
Chapter 4: BIOS setup
Intel LAN4 Enable [Enabled] (Z9PE-D16
���������������
only)
Allows you to enable or disable Intel® LAN4 function. Configuration options:
[Disabled] [Enabled]
LAN4 Option ROM Support [Enabled] (Z9PE-D16 only)
Configuration options: [Disabled] [Enabled]
4.4.8
Intel TXT(LT-SX) Configuration
The Intel TXT(LT-SX) configuration automatically detects and displays the Intel®
TXT(LT-SX) hardware support.
®
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel TXT(LT-SX) Hardware Support
CPU: TXT Feature
Chipset: TXT Feature
Supported
Supported
Intel TXT(LT-SX) Configuration
TXT Support
Disabled
Intel TXT(LT-SX) Dependencies
The following must be supported and enabled.
VT-d Support
Disabled
VT Support
Enabled
TPM Support
Enabled
TPM State
Disabled
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.14.1219. Copyright (C) 2011 American Megatrends, Inc.
ASUS Z9PE-D16 Series
4-27
4.4.9
USB Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
USB Configuration
USB Devices:
3Drivers, 1Keyboard, 1 Mouse, 3 Hubs
Legacy USB Support EHCI Hand-off [Enabled]
[Disabled]
USB hardware delays and time-outs
USB transfer time-out Device reset time-out [20 sec]
[20 sec]
Enabled Legacy USB support.
Auto option disables legacy
support if no USB devices
are connected. DISABLE
option will keep USB devices
available only for EFI
applications.
USB Ports Configuration
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Legacy USB Support [Enabled]
Allows you to enable or disable Legacy USB device support.
Configuration options: [Enabled] [Disabled] [Auto]
EHCI Hand-off [Disabled]
This is a workaround for 0ses without EHCI. Ownership change should be claimed
by EHCI driver.
Configuration options: [Disabled] [Enabled]
USB hardware delays and time-outs
USB transfer time-out [20 sec]
The time-out value for control, bulk, and interrupt transfer.
Configuration options: [1 sec] [5 sec] [10 sec] [20 sec]
Device reset time-out [20 sec]
USB mass storage device start unit command time-out.
Configuration options: [10 sec] [20 sec] [30 sec] [40 sec]
4-28
Chapter 4: BIOS setup
USB Ports Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
EHCI Controller 1 EHCI Controller 2 [Enabled]
[Enabled]
Rear USB #1 Rear USB #2
Onboard USB #3 Onboard USB #4 Onboard USB #5
Onboard USB #6 Onboard USB #10
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
Enable/disable USB 2.0 (EHCI)
Support.
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
EHCI Controller 1/2 [Enabled]
Allows you to enable or disable USB (EHCI) Support.
Configuration options: [Disabled] [Enabled]
Rear USB #1 and #2 [Enabled]
Allows you to enable or disable rear USB #1 and #2.
Configuration options: [Disabled] [Enabled]
Onboard USB #3/#4/#5/#6/#10 [Enabled]
Allows you to enable or disable Onboard USB #3 / #4 / #5 / #6 / #10.
Configuration options: [Disabled] [Enabled]
4.4.10
Trusted Computing
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Configuration
TPM Support [Enabled]
Current Status Information
No Security Device Found
Allows you to enable or
disable BIOS support for
security device. O.S. will
not show Security Device.
TCG EFI protocol and INT1A
interface will not be
TPM Support [Enabled]
Allows you to enable or disable the TPM support.
Configuration options: [Disabled] [Enabled]
ASUS Z9PE-D16 Series
4-29
4.4.11
ACPI Settings
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
ACPI Settings
Enable ACPI Auto Configuration [Disabled]
Enabled Hibernation
ACPI Sleep State
Lock Legacy Resources
Allows you to enable or
disable BIOS ACPI Auto
Configuration.
[Enabled]
[S1 (CPU Stop Clock)]
[Disabled]
Enable ACPI Auto Configuration [Disabled]
Allows you to enable or disable BIOS ACPI Auto Configuration.
Configuration options: [Disabled] [Enabled]
The following item appears only when you set Enabled ACPI Auto
Configuration to [Disabled].
Enable Hibernation [Enabled]
Allows you to enable or disable system ability to Hibernate (OS/S4 sleep state).
This option may be not effective with some OS.
Configuration options: [Disabled] [Enabled]
ACPI Sleep State [S1 (CPU Stop Clock)]
Allows you to set the ACPI Sleep State.
Configuration options: [Suspend Disabled] [S1 (CPU Stop Clock)] [S3 (Suspend to
RAM)]
Lock Legacy Resources [Disabled]
Allows you to enable or disable Lock Legacy Resources.
Configuration options: [Disabled] [Enabled]
4-30
Chapter 4: BIOS setup
4.4.12
WHEA Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
WHEA Support
[Enabled]
Enable or disable Windows
Hardware Error Architecture.
WHEA Support [Enabled]
Allows you to enable or disable the Windows Hardware Error Architecture support.
Configuration options: [Disabled] [Enabled]
4.4.13
APM setting
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Restrore AC Power Loss
Power On By PCIE
Power On By RTC
[Last State]
[Disabled]
[Disabled]
Specify what state to go to
when power is re-applied after
a power failure (G3 state).
Restore AC Power Loss [Last State]
When set to [Power Off], the system goes into off state after an AC power loss.
When set to [Power On], the system will reboot after an AC power loss. When set
to [Last State], the system goes into either off or on state, whatever the system
state was before the AC power loss.
Configuration options: [Power Off] [Power On] [Last State]
Power On By PCIE [Disabled]
[Disabled]Disables the PCIE devices to generate a wake event.
[Enabled]Enables the PCIE devices to generate a wake event.
Power On By RTC [Disabled]
[Disabled]Disables RTC to generate a wake event.
[Enabled]When set to [Enabled], the items RTC Alarm Date (Days) and
Hour/Minute/Second will become user-configurable with set
values.
ASUS Z9PE-D16 Series
4-31
4.4.14
Serial Port Console Redirection
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
COM1
Console Redirection
Console Redirection Settings
[Disabled]
COM2
Console Redirection
Console Redirection Settings
[Enabled]
Serial Port for Out-of-Band Management/
Windows Emergency Management Services (EMS)
Console Redirection
[Disabled]
Console Redirection Settings
Consloe Redirection Enable
or Disable.
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
COM1
Console Redirection [Disabled]
Allows you to enable or disable the console redirection feature.
Configuration options: [Disabled] [Enabled]
The following item appears only when you set Console Redirection to
[Enabled].
Console Redirection Settings
This item becomes configurable only when you enable the Console Redirection
item. The settings specify how the host computer and the remote computer (which
the user is using) will exchange data. Both computers should have the same or
compatible settings.
Terminal Type [VT-UTF8]
Allows you to set the terminal type.
[VT100] ASCII char set.
[VT100+] Extends VT100 to support color, function keys, et.
[VT-UTF8]Uses UTF8 encoding to map Unicode chars onto 1 or more bytes
[ANSI] Extended ASCII char set
Bits per second [57600]
Selects serial port transmission speed. The speed must be matched on the
other side. Long or noisy lines may require lower speeds.
Configuration options: [9600] [19200] [38400] [57600] [115200]
4-32
Chapter 4: BIOS setup
Data Bits [8]
Configuration options: [7] [8]
Parity [None]
A parity bit can be sent with the data bits to detect some transmission errors.
[Mark] and [Space] parity do not allow for error detection.
[None] None
[Even]
parity bit is 0 if the num of 1’s in the data bits is even
[Odd]
parity bit is 0 if num of 1’s in the data bits is odd
[Mark]
parity bit is always 1
[Space] parity bit is always 0
Stop Bits [1]
Stop bits indicate the end of a serial data packet. (A start bit indicates the
beginning.) The standard setting is 1 stop bit. Communication with slow
devices may require more than 1 stop bit. Configuration options: [1] [2]
Flow Control [Hardware RTS/CTS]
Flow control can prevent data loss from buffer overflow. When sending data,
if the receiving buffers are full, a “stop” signal can be sent to stop the data
flow. Once the buffers are empty, a “start” signal can be sent to re-start the
flow. Hardware flow control uses two wires to send start/stop signals.
Configuration options: [None] [Hardware RTS/CTS]
Recorder Mode [Disabled]
With this mode enabled only text will be sent. This is to capture Terminal data.
Configuration options: [Disabled] [Enabled]
Recorder 100x31 [Disabled]
Allows you to enable or disable extend terminal resolution.
Configuration options: [Disabled] [Enabled]
Legacy OS Redirction Resolution [80x24]
Configures the number of rows and columns supported on legacy OS.
Configuration options: [80x24] [80x25]
COM2
Console Redirection [Enabled]
Allows you to enable or disable the console redirection feature.
Configuration options: [Disabled] [Enabled]
Console Redirection Settings
Please refer to the description of the Console Redirection Settings item under
COM1 for details.
ASUS Z9PE-D16 Series
4-33
Serial Port for Out-of-Band Management/
Windows Emergency Management Services (EMS)
Console Redirection [Disabled]
Allows you to enable or disable the console redirection feature.
Configuration options: [Disabled] [Enabled]
The following item appears only when you set Console Redirection to
[Enabled].
Console Redirection Settings
Out-of-Band Mgmt Port [COM1]
Microsoft Windows Emergency Management Services (EMS) allow for
remote management of a Windows Server OS through a serial port.
Configuration options: [COM1] [COM2]
Terminal Type [VT-UTF8]
Microsoft Windows Emergency Management Services (EMS) allow for
remote management of a Windows Server OS through a serial port.
Configuration options: [VT100] [VT100+] [VT-UTF8] [ANSI]
Bits per second [115200]
Microsoft Windows Emergency Management Services (EMS) allow for
remote management of a Windows Server OS through a serial port.
Configuration options: [9600] [19200] [57600] [115200]
Flow Control [None]
Microsoft Windows Emergency Management Services (EMS) allow for
remote management of a Windows Server OS through a serial port.
Configuration options: [VT100] [Hardware RTS/CTS] [Software Xon/Xoff]
4-34
Chapter 4: BIOS setup
4.4.15
ME Subsystem
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Intel ME Subsystem Configuration
ME BIOS Interface Version
1.2
ME Version
ME FW Status Value :
ME FW State
:
ME FW Operation State:
ME FW Error Code:
ME Ext FW Status value:
BIOS Booting Mode:
Cores Disabled:
ME FW SKU Information:
ME Subsystem Help.
2.1.5.64
0xf0345
SPS ME FW Active
M0 without UMA
No Error
0x39006301
Performance Optimized
0
SiEn NM
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
4.4.16
Legacy Devices Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Set Parameters of serial
Port 1(COM1).
Serial Port 1 Configuration
Serial Port 2 Configuration
Serial Port 1/2 Configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Enable or Disable Serial
Port(COM).
Serial Port Configuration
Serial Port
Device Settings
Device Mode
ASUS Z9PE-D16 Series
[Enabled]
I0=3F8h; IRQ=4
[Standard Serial Po...]
4-35
Serial Port [Enabled]
Allows you to enable or disable the serial port.
Configuration options: [Disabled] [Enabled]
Device Mode [Standard Serial Port Mode]
Allows you to change the serial port mode.
Configuration options: [Standard Serial Port Mode]
4.4.17
Runtime Error Logging
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced
Runtime Error Logging Support
[Disabled]
Runtime Error Logging Support [Disabled]
This item allows you to enable or disable Runtime Error Logging Support.
Configuration options: [Disabled] [Enabled]
The following item appears only when you set Runtime Error Logging Support
to [Enabled].
PCI Error Logging Support [Disabled]
Allows you to enable or disable PCI Error Logging.
Configuration options: [Disabled] [Enabled].
4-36
Chapter 4: BIOS setup
4.5
Server Mgmt menu
The Server Mgmt menu displays the server mgmt status, and allows you to change
the settings.
The Server Mgmt menu appears only when you install ASMB card on the
motherboard.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Server Mgmt Event Logs Boot Monitor Security Tool Exit
BMC Firmware:
O/S Watchdog Timer
O/S Wtd Timer Timeout
O/S Wtd Timer Policy
System Event Log
BMC network configuration
x.xx
[Disabled]
[10 minutes]
[Reset]
Wait for BMC response for
specified timeout In PILOTII,
BMC starts at the same time
when BIOS starts during AC
power ON. It takes arround
30 seconds to initialize
Host to BMC interfaces.
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
O/S Watchdog Timer [Disabled]
If enabled, starts a BIOS timer which can only be shut off by Intel Management
Software after the OS loads. Helps determine that the OS sucessfully loaded or
follows the O/S Boot Watchdog TImer Policy.
Configuration options: [Enabled] [Disabled]
The following two items allows you setting only when you set O/S Watchdog
Timer to [Enabled].
O/S Wtd Timer Timeout [10 minutes]
Allows you to configure the length of the O/S Boot Watchdog Timer. Not available if
O/S Boot Watchdog Timer is disabled.
Configuration options: [5 minutes] [10 minutes] [15 minutes] [20 minutes]
O/S Wtd Timer Policy [Reset]
Allows you to configure how the system should respond if the OS Boot Watchdog
Timer expires. Not available if O/S Boot Watchdog Timer is disabled.
Configuration options: [Do Nothing] [Reset] [Power Down]
ASUS Z9PE-D16 Series
4-37
4.5.1
System Event Log
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Server Mgmt
Enabling/Disabling Options
SEL Components
[Disabled]
Erasing Settings
Erase SEL
When SEL is Full
[No]
[Do Nothing]
Note: All values changed here do not take effect
until computer is restarted.
Change this to enable or
disable all features of
system Event Logging during
boot.
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
SEL Components [Disabled]
Allows you to enable or disable all features of system Event Logging during boot.
Configuration options: [Disabled] [Enabled]
•
The following items appears only when you set SEL Components to
[Enabled].
•
All values changed here do not take effect until computer is restarted.
Erase SEL [No]
Allows you to choose options for erasing SEL.
Configuration options: [No] [Yes, On next reset] [Yes, On every reset]
When SEL is Full [Do Nothing]
Allows you to choose options for reactions to a full SEL.
Configuration options: [Do Nothing] [Erase Immediately]
4-38
Chapter 4: BIOS setup
4.5.2
BMC network configuration
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Server Mgmt
BMC network configuration
DM_KAN1
DM_LAN1 IP Address in BMC:
DM_LAN1 Subnet Mask in BMC:
DM_LAN1 Gateway Address in BMC:
DM_LAN1 MAC Address in BMC:
DM_LAN1 Address Source in BMC:
Configuration Address source
192.168.001.001
255.255.255.000
000.000.000.000
00.CE.01.87.72.A0
Static Mode
[Previous State]
Lan1
Lan1
Lan1
Lan1
Lan1
Lan1
IP Address in BMC:
Subnet Mask in BMC:
Gateway Address in BMC:
MAC Address in BMC:
Address Source in BMC:
Configuration Address source
192.168.001.002
255.255.255.000
000.000.000.000
00.CE.01.87.72.A0
Static Mode
[Previous State]
Select to configure LAN
channel parameters
statically or dynamically(by
BIOS or BMC). Unspecified
option will not modify any
BMC network parameters
during BIOS phase
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Configuration Address source [Previous State]
Select to configure LAN channel parameters statically or dynamically(by BIOS
or BMC). Unspecified option will not modify any BMC network parameters during
BIOS phase.
Configuration options: [Previous State] [Static Mode] [DHCP Mode]
The following items appears only when you set Configuration Address source
to [Static Mode].
Station IP address [0.0.0.0]
Allows you to input Station IP address.
Subnet mask [0.0.0.0]
Allows you to input Subnet mask.
Gateway IP address [0.0.0.0]
Allows you to input Gateway IP address.
ASUS Z9PE-D16 Series
4-39
4.6
Event Logs menu
The Event Logs allows you to change or view the event log settings.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Server Mgmt Event Logs Boot Monitor Security Tool Exit
Press <Enter> to change
the Smbios Event Log
configuration.
Change Smbios Event Log Settings
View Smbios Event Log
View System Event Log
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
4.6.1
Change Smbios Event Log Settings
Press <Enter> to change the Smbios Event Log configuration.
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Event Logs
Enabling/Disabling Options
Smbios Event Log
[Enabled]
Erasing Settings
Erase Event Log
When Log is Full
[No]
[Do Nothing]
Smbios Event Log Standard Settings
Log System Boot Event
[Disabled]
MECI
1
METW
60
Custom Option
Log OEM Codes
[Enabled]
Convert OEM Codes
[Disabled]
Note: All values changed here do not take effect
until computer is restarted.
Change this to enable or
disable all features of
Smbios Event Logging during
boot.
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
All values changed here do not take effect until computer is restarted.
Enabling/Disabling Options
Smbios Event Log [Enabled]
Change this to enable or disable all features of Smbios Event Logging during
boot.Configuration options: [Disabled] [Enabled]
4-40
Chapter 4: BIOS setup
Erasing Settings
Erase Event Log [No]
Choose options for erasing Smbios Event Log. Erasing is done prior to any
logging activation during reset.
Configuration options: [No] [Yes, Next reset] [Yes, Every reset]
When Log is Full [Do Nothing]
Allows you to choose options for reactions to a full Smbios Event Log.
Configuration options: [Do Nothing] [Erase Immediately]
Smbios Event Log Standard Settings
Log System Boot Event [Disabled]
Allows you to choose options to enable/disable logging of System boot event.
Configuration options: [Enabled] [Disabled]
MECI [1]
Mutiple Event Count Increment (MECI). The number of occurrences of a
duplicate event that must pass before the multiplt-event counter associated
with the log entry is updated, specified as a numeric value in the range 1 to
255.
METW [60]
Mutiple Event Time Windows (METW). The number of minutes which must
pass between duplicate log entries which utilize a multiple-event counter. The
value ranges from 0 to 99 minutes.
Custom Option
Log OEM Codes [Enabled]
Enable or disable the logging of EFI Status Codes as OEM Codes (if not
already converted to legacy).
Configuration options: [Disabled] [Enabled]
Convert OEM Codes [Disabled]
Enable or disable the converting of EFI Status Codes to Standard Smbios
Types (Not all may be translated).
Configuration options: [Disabled] [Enabled]
View Smbios Event Log
Press <Enter> to view all smbios event logs.
View System Event Log
Press <Enter> to view all system event logs.
ASUS Z9PE-D16 Series
4-41
4.7
Boot menu
The Boot menu items allow you to change the system boot options.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Server Mgmt Event Logs Boot Monitor Security Tool Exit
Boot Configuration
Setup Prompt Timeout
Bootup NumLock State
1
[On]
Full Screen Logo
[Enabled]
CSM16 Module Version
07.67
GateA20 Active
Option ROM Messages
Interrupt 19 Capture
Boot Device Seeking
UEFI Boot
[Upon Request]
[Force BIOS]
[Enabled]
[Endless PXE]
[Disabled]
Boot
Boot
Boot
Boot
Boot
[SATA P2: ASUS
...]
[SATA P3: WDC WD80...]
[AMI Virtual Floppy...]
[IBA GE Slot 0700 v...]
Option
Option
Option
Option
Option
Priorities
#1
#2
#3
#4
Number of seconds to wait for
setup activation key.
65535(0xFFFF) means indefinite
waiting.
CD/DVD ROM Drive BBS Priorities
Hard Drive BBS Priorities
Floppy Drive BBS Priorities
Network Device BBS Priorities
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Setup Prompt Timeout [xx]
Use the <+> and <-> keys to adjust the number of seconds to wait for setup
activation key.
Bootup NumLock State [On]
Allows you to select the power-on state for the NumLock.
Configuration options: [Off] [On]
Full Screen Logo [Enabled]
Allows you to enable or disable the full screen logo display feature.
Configuration options: [Disabled] [Enabled]
Set this item to [Enabled] to use the ASUS MyLogo2™ feature.
GateA20 Active [Upon Request]
[Upon Request] GA20 can be disabled using BIOS services.
[Always] Do not allow disable GA20; this option useful when any RT code is
executed above 1MB.
Option ROM Messages [Force BIOS]
Allows you to set the display mode for Options ROM.
Configuration options: [Force BIOS] [Keep Current]
4-42
Chapter 4: BIOS setup
Interrupt 19 Capture [Enabled]
Allows Option ROMs to trap interrupt 19.
Configuration options: [Disabled] [Enabled]
Boot Device Seeking [Endless PXE]
[Endless PXE] Continuous seek remote boot image until boot image found or user
abort (press Ctrl+Alt+Del).
[Normal]
Seek remote boot image once then stop.
UEFI Boot [Disabled]
Allows you to enable or disable UEFI Boot.
Configuration options: [Disabled] [Enabled]
Boot Option Priorities
These items specify the boot device priority sequence from the available devices.
The number of device items that appears on the screen depends on the number of
devices installed in the system.
•
To select the boot device during system startup, press <F8> when ASUS
Logo appears.
•
To access Windows OS in Safe Mode, please press <F8> after POST.
Set the booting order of network devices.
Boot Option #1/#2/#3/#4 [SATA P2: ASUS ...]
Configuration options: [SATA P2: ASUS ...] [SATA P3: WDC WD80...]
[AMI Virtual Floppy...] [IBA GE Slot 0700 v...]
CD/DVD ROM Drive BBS Priorities
Hard Drive BBS Priorities
Floppy Drive BBS Priorities
Network Device BBS Priorities
These items appear only when you connect SATA ODD or hard drive to the
SATA ports and allow you to set the booting order of the SATA devices.
ASUS Z9PE-D16 Series
4-43
4.8
Monitor menu
The Monitor menu displays the system temperature/power status, and allows you
to change the fan settings.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Server Mgmt Event Logs Boot Monitor Security Tool Exit
CPU1 Temperature
CPU2 Temperature
TR1 Temperature
TR2 Temperature
CPU FAN1 Speed
CPU FAN2 Speed
FRNT FAN1 Speed
FRNT FAN2 Speed
FRNT FAN3 Speed
FRNT FAN4 Speed
REAR FAN1 Speed
REAR FAN2 Speed
+VTT_CPU
VCORE1
VCORE2
+VDDQ_AB_CPU1
+VDDQ_CD_CPU1
+VDDQ_EF_CPU2
+VDDQ_GH_CPU2
+5VSB
+5V
+12V
+3.3V
VBAT
+3.3VSB
54.0ºC/129.2ºF
N/A
35.0ºC/95.0ºF
40.0ºC/104.0ºF
5378 RPM
N/A
N/A
N/A
N/A
N/A
N/A
N/A
+1.026 V
+0.996 V
+0.996 V
+1.510 V
+1.526 V
N/A
N/A
+4.996 V
+4.996 V
+11.592 V
+3.276 V
+3.168 V
+3.234 V
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Scroll down to display the following items:
FAN Speed Control
[Generic Node]
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
CPU 1/2; TR1 1/2 Temperature �������������
[xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the CPU and
motherboard component temperatures.
CPU FAN1/2 Speed; FRNT FAN1–4 Speed; REAR FAN1/2 Speed
[xxxx RPM] or [N/A]
The onboard hardware monitor automatically detects and displays the speed of
CPU fans, front fans, and rear fan in rotations per minute (RPM). If the fan is not
connected to the motherboard, the field shows N/A.
4-44
Chapter 4: BIOS setup
+VTT_CPU Voltage, VCORE1/2 Voltage, +VDDQ_AB_CPU1
Voltage, +VDDQ_CD_CPU1 Voltage, +VDDQ_EF_CPU2 Voltage,
+VDDQ_GH_CPU2 Voltage, +5VSB Voltage, +5V Voltage, +12V
Voltage, +3.3V Voltage, VBAT Voltage, +3.3VSB Voltage
The onboard hardware monitor automatically detects the voltage output through
the onboard voltage regulators.
FAN Speed Control [Generic Mode]
Allows you to configure the ASUS Smart Fan feature that smartly adjusts the fan
speeds for more efficient system operation.
Configuration options: [Generic Mode] [High Speed Mode] [Full Speed Mode]
4.9
Security menu
The Security menu items allow you to change the system security settings.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Server Mgmt Event Logs Boot Monitor Security Tool Exit
Password Description
If ONLY the Administrator's password is set,
then this only limits access to Setup and is
only asked for when entering Setup
If ONLY the User's password is set, then this
is a power on password and must be entered to
boot or enter Setup. In Setup the User will
have Administrator rights
The password length must br in the following range:
Minimum length 3
Maximum length 20
Set Setup Administrator
Password
Administrator Password
User Password
•
If you have forgotten your BIOS password, erase the CMOS Real Time
Clock (RTC) RAM to clear the BIOS password. See section 2.6 Jumpers
for information on how to erase the RTC RAM.
•
The Administrator or User Password items on top of the screen show
the default Not Installed. After you set a password, these items show
Installed.
ASUS Z9PE-D16 Series
4-45
Administrator Password
If you have set an administrator password, we recommend that you enter the
administrator password for accessing the system. Otherwise, you might be able to
see or change only selected fields in the BIOS setup program.
To set an administrator password:
1.
2.
3.
Select the Administrator Password item and press <Enter>.
From the Create New Password box, key in a password, then press
<Enter>.
Confirm the password when prompted.
To change an administrator password:
1.
2.
3.
4.
Select the Administrator Password item and press <Enter>.
From the Enter Current Password box, key in the current password, then
press <Enter>.
From the Create New Password box, key in a new password, then press
<Enter>.
Confirm the password when prompted.
To clear the administrator password, follow the same steps as in changing an
administrator password, but press <Enter> when prompted to create/confirm the
password. After you clear the password, the Administrator Password item on top
of the screen shows Not Installed.
User Password
If you have set a user password, you must enter the user password for accessing
the system. The User Password item on top of the screen shows the default Not
Installed. After you set a password, this item shows Installed.
To set a user password:
1.
2.
3.
Select the User Password item and press <Enter>.
From the Create New Password box, key in a password, then press
<Enter>.
Confirm the password when prompted.
To change a user password:
1.
2.
3.
4.
4-46
Select the User Password item and press <Enter>.
From the Enter Current Password box, key in the current password, then
press <Enter>.
From the Create New Password box, key in a new password, then press
<Enter>.
Confirm the password when prompted.
Chapter 4: BIOS setup
To clear the user password, follow the same steps as in changing a user password,
but press <Enter> when prompted to create/confirm the password. After you clear
the password, the User Password item on top of the screen shows Not Installed.
4.10 Tool menu
The Tool menu items allow you to configure options for special functions. Select an
item then press <Enter> to display the submenu.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Server Mgmt Event Logs Boot Monitor Security Tool Exit
ASUS EZ Flash 2 Utility
Be used to update BIOS
ASUS EZ Flash 2 Utility
Allows you to run ASUS EZ Flash BIOS ROM Utility when you press <Enter>.
Check section 5.1.2 ASUS EZ Flash 2 Utility for details.
4.11 Exit menu
The Exit menu items allow you to save or discard your changes to the BIOS items.
Main
Aptio Setup Utility - Copyright (C) 2011 American Megatrends, Inc.
Advanced Server Mgmt Event Logs Boot Monitor Security Tool Exit
Discard Changes & Exit
Save Changes & Reset
Discard Changes & Reset
Exit system setup without
saving any changes.
Restore Defaults
Boot Override
SATA P2: ASUS
DRW-2014L1T
AMI Virtual CDROM 1.00
SATA P3: WDC WD800JD-00LSA0
AMI Virtual Floppy0 1.00
IBA GE Slot 0700 v1376
IBA GE Slot 0701 v1376
IBA GE Slot 0702 v1376
IBA GE Slot 0703 v1376
Launch EFI Shell from filesystem device
→←: Select Screen
↑↓: Select Item
Enter: Select Item
+/-: Change Opt.
F1: General Help
F2: Previous Values
F5: Optimized Defaults
F10: Save & Exit
ESC: Exit
Version 2.15.1219. Copyright (C) 2011 American Megatrends, Inc.
Pressing <Esc> does not immediately exit this menu. Select one of the options
from this menu or <F10> from the legend bar to exit.
ASUS Z9PE-D16 Series
4-47
Boot Override
These items displays the available devices. The device items that appears on the
screen depends on the number of devices installed in the system. Click an item to
start booting from the selected device.
Launch EFI Shell from filesystem device
Attempts to launch EFI Shell application (shellx64.efi) from one of the available
filesystem devices.
Discard Changes & Exit
This option allows you to exit the Setup program without saving your changes. When
you select this option or if you press <Esc>, a confirmation window appears. Select
Yes to discard changes and exit.
Save Changes & Reset
Once you are finished making your selections, choose this option from the Exit menu to
ensure the values you selected are saved. When you select this option or if you press
<F10>, a confirmation window appears. Select Yes to save changes and exit.
Discard Changes & Reset
This option allows you to reset the Setup program without saving your changes.
When you select this option, a confirmation window appears. Select Yes to discard
changes and reset.
Restore Defaults
This option allows you to restore/load defaults values for all the setup options. When
you select this option, a confirmation window appears. Select Yes to load optimized
defaults.
4-48
Chapter 4: BIOS setup
This chapter provides instructions for
setting up, creating, and configuring RAID
sets using the available utilities.
5
RAID
configuration
Chapter summary
5
5.1
Setting up RAID............................................................................. 5-3
5.3
Intel® Rapid Storage Technology enterprise SCU /SATA Option
ROM Utility................................................................................... 5-25
5.2
5.4
LSI Software RAID Configuration Utility..................................... 5-5
Intel® Rapid Storage Technology enterprise Utility(Windows).... 5-35
ASUS Z9PE-D16 Series
5.1
Setting up RAID
The motherboard supports the following SATA RAID solutions:
•
•
LSI MegaRAID software RAID Configuration Utility with RAID 0, RAID 1,
and RAID 10 support (for both Linux and Windows OS).
Intel Rapid Storage Technology enterprise SCU / SATA Option ROM Utility
with RAID 0, RAID 1, RAID 10, and RAID 5 support (for Windows OS only).
5.1.1
RAID definitions
RAID 0 (Data striping) optimizes two identical hard disk drives to read and write
data in parallel, interleaved stacks. Two hard disks perform the same work as a
single drive but at a sustained data transfer rate, double that of a single disk alone,
thus improving data access and storage. Use of two new identical hard disk drives
is required for this setup.
RAID 1 (Data mirroring) copies and maintains an identical image of data from one
drive to a second drive. If one drive fails, the disk array management software
directs all applications to the surviving drive as it contains a complete copy of
the data in the other drive. This RAID configuration provides data protection and
increases fault tolerance to the entire system. Use two new drives or use an
existing drive and a new drive for this setup. The new drive must be of the same
size or larger than the existing drive.
RAID 1E (Enhanced RAID 1) has a striped layout with each stripe unit having a
secondary (or alternate) copy stored on a different disk. You can use three or more
hard disk drives for this configuration.
RAID 10 is data striping and data mirroring combined without parity (redundancy
data) having to be calculated and written. With the RAID 10 configuration you get
all the benefits of both RAID 0 and RAID 1 configurations. Use four new hard disk
drives or use an existing drive and three new drives for this setup.
RAID 5 stripes both data and parity information across three or more hard disk
drives. Among the advantages of RAID 5 configuration include better HDD
performance, fault tolerance, and higher storage capacity. The RAID 5 configuration
is best suited for transaction processing, relational database applications,
enterprise resource planning, and other business systems. Use a minimum of three
identical hard disk drives for this setup.
•
If you want to boot the system from a hard disk drive included in a created
RAID set, copy first the RAID driver from the support DVD to a floppy disk
before you install an operating system to the selected hard disk drive.
•
Please refer to chapter 2 for how to select the RAID configuration utility.
Move the jumper to choose between LSI MegaRAID and Intel® Rapid RAID.
ASUS Z9PE-D16 Series
5-3
5.1.2
Installing hard disk drives
The motherboard supports Serial ATA for RAID set configuration. For optimal
performance, install identical drives of the same model and capacity when creating
a disk array.
To install the SATA hard disks for RAID configuration:
1.
2.
3.
Install the SATA hard disks into the drive bays following the instructions in the
system user guide.
Connect a SATA signal cable to the signal connector at the back of each drive
and to the SATA connector on the motherboard.
Connect a SATA power cable to the power connector on each drive.
5.1.3
Setting the RAID item in BIOS
You must set the RAID item in the BIOS Setup before you can create a RAID set
from SATA hard disk drives attached to the SATA connectors supported by
Intel® C602 chipset. To do this:
1.
Enter the BIOS Setup during POST.
3.
Set SATA Mode to [RAID Mode]
2.
4.
Go to the Advanced Menu > PCH SATA Configuration, then press <Enter>.
Press <F10> to save your changes and exit the BIOS Setup.
Refer to Chapter 4 for details on entering and navigating through the BIOS
Setup.
5.1.4
RAID configuration utilities
Depending on the RAID connectors that you use, you can create a RAID set using
the utilities embedded in each RAID controller. For example, use the LSI Logic
Embedded SATA RAID Setup Utility or the Intel® Rapid Storage Technology if
you installed Serial ATA hard disk drives on the Serial ATA connectors supported by
the Intel® C602 chipset.
Refer to the succeeding section for details on how to use the RAID configuration
utility.
5-4
Chapter 5: RAID configuration
5.2LSI Software RAID Configuration Utility
The LSI MegaRAID software RAID configuration utility allows you to create RAID 0,
RAID 1, or RAID 10 set(s) from SATA hard disk drives connected to the SATA
connectors supported by the motherboard southbridge chip.
To enter the LSI MegaRAID software RAID configuration utility:
1.
2.
Turn on the system after installing all the SATA hard disk drives.
During POST, the LSI MegaRAID software RAID configuration utility
automatically detects the installed SATA hard disk drives and displays any
existing RAID set(s). Press <Ctrl> + <M> to enter the utility.
LSI MegaRAID Software RAID BIOS Version A.10 09231523R
LSI SATA RAID Found at PCI Bus No:00 Dev No:1F
Device present at Port 0
ST3160812AS
152114MB
Device present at Port 1
ST3160812AS
152114MB
Device present at Port 2
ST3160812AS
152114MB
Device present at Port 3
ST3160812AS
152114MB
Press Ctrl-M or Enter to run LSI Software RAID Setup Utility.
3.
•
The LSI MegaRAID software RAID configuration utility automatically
configures to RAID 1 when the SATA to RAID Mode is enabled.
•
The RAID setup screens shown in this section are for reference only and
may not exactly match the items on your screen due to the controller
version difference.
•
When you create RAID sets with the LSI MegaRAID software RAID
configuration utility, the boot priority of the SATA optical drive has to be
manually adjusted. Otherwise, the system will not boot from the connected
SATA ODD.
The utility main window appears. Use the arrow keys to select an option from
the Management Menu and then press <Enter>. Refer to the Management
Menu descriptions on the next page.
At the bottom of the screen is the legend box. The keys on the legend box
allow you to navigate through the setup menu options or execute commands.
The keys on the legend box vary according to the menu level.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Configure VD(s)
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
ASUS Z9PE-D16 Series
5-5
Menu
Description
Configure
Allows you to create RAID 0, RAID 1 or RAID 10 set using the Easy
Configuration or the New Configuration command. This menu also
allows you to view, add, or clear RAID configurations or select the
boot drive
Initialize
Allows you to initialize the virtual drives of a created RAID set
Objects
Allows you to initialize virtual drives or change the virtual drive
parameters
Rebuild
Allows you to rebuild failed drives
Check Consistency Allows you to check the data consistency of the virtual drives of a
created RAID set
5.2.1
Creating a RAID set
The LSI Software RAID Configuration Utility allows you to create a RAID 0, RAID
1, or RAID 10 set using two types of configurations: Easy and New.
In Easy Configuration, the virtual drive parameters are set automatically.
In New Configuration, you manually set the virtual drive parameters.
Using Easy Configuration
To create a RAID set using the Easy Configuration option:
1.
From the Management Menu, select Configure > Easy Configuration, and
then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
Defines Physical Arrays. An Array Will Automatically Become A VD
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
5-6
Chapter 5: RAID configuration
2.
The ARRAY SELECTION MENU displays the available drives connected to
the SATA ports. Use the up/down arrow keys to select the drives you want to
include in the RAID set, and then press <Space>. When selected, the drive
indicator changes from READY to ONLIN A[X]-[Y], where X is the array
number, and Y is the drive number.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Easy Configuration - ARRAY SELECTION MENU
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
PORT #
0 ONLIN A00-00
1 ONLIN A00-01
2 READY
3 READY
Port # 2 DISK
74.74GB
HDS728080PLA380
05.01C05
SPACE-Sel,ENTER-EndArray,F10-Configure,F2-Drive Info,F3-Virtual Drives,F4-HSP
3.
4.
•
The information of the selected hard disk drive displays at the bottom of the
screen.
•
You need at least two identical hard disk drives when creating a RAID 1 set.
•
You need at least four identical hard disk drives when creating a RAID 10
set.
Select all the drives required for the RAID set, and then press <F10> to
configure array setting.
Press <Space> to select the configurable array.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Easy Configuration - ARRAY SELECTION MENU
Select Configurable Array(s)
PORT #
A-0
0 DNLIN A00-00
SPAN-1
1 DNLIN A00-01
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Configure Esc-Quit
ASUS Z9PE-D16 Series
5-7
5.
Press <F10> again, the virtual drive information appears including a Virtual
Drive menu that allows you to change the virtual drive parameters.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Virtual
VersionDrive(s)
A.10.09231523R
Configured
LD
RAID
Size
#Stripes
StripSzMENU Status
Easy Configuration
- ARRAY SELECTION
Management
0 Menu 1
148.580GB PORT
2 #
Configure
0 DNLIN A00-00
Initialize
Objects
1 DNLIN A00-01
Rebuild
Check Consistency
Virtual Drive 0
RAID = 1
Units= MB
Size = 152146MB
DWC = Off
RA = On
Accept
SPAN = NO
64 KB
ONLINE
Choose RAID Level For This VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
6.
7.
Select RAID from the Virtual Drive sub-menu, and then press <Enter>.
Select the RAID level from the menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Virtual
VersionDrive(s)
A.10.09231523R
Configured
LD
RAID
Size
#Stripes
StripSzMENU Status
Easy Configuration
- ARRAY SELECTION
Management
0 Menu 1
148.580GB PORT
2 #
64 KB
Configure
0 DNLIN A00-00
Initialize
Objects
1 DNLIN A00-01
Rebuild
Check Consistency
Virtual Drive 0
RAID Level
RAID = 1
RAID 0
Units= MB
RAID 1
Size = 152146MB
DWC = Off
RA = On
Accept
SPAN = NO
ONLINE
Choose RAID Level For This VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
5-8
Chapter 5: RAID configuration
8.
9.
Select Units from the Virtual Drive sub-menu, and then press <Enter>.
Select the units for virtual drive size from the menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Virtual
VersionDrive(s)
A.10.09231523R
Configured
LD
RAID
Size
#Stripes
StripSzMENU Status
Easy Configuration
- ARRAY SELECTION
Management
0 Menu 1
148.580GB PORT
2 #
64 KB
ONLINE
Configure
0 DNLIN A00-00
Initialize
Objects
1 DNLIN A00-01
Rebuild
Select Units For VD Size
Check Consistency
MB
Virtual Drive 0
GB
RAID = 1
TB
Units= MB
Size = 152146MB
DWC = Off
RA = On
Accept
SPAN = NO
Select Units For VD Size
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
10. When creating a RAID 1 or a RAID 10 set, select DWC from the Virtual
Drive menu, and then press <Enter>.
When creating a RAID 0 set, proceed to step 12.
11. Select On to enable the Disk Write Cache setting, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOSVirtual
VersionDrive(s)
A.10.09231523R
Configured
LD
RAID
Size
#Stripes
StripSzMENU Status
Easy Configuration
- ARRAY SELECTION
Management
0 Menu 1
148.580GB PORT
2 #
64 KB
Configure
0 DNLIN A00-00
Initialize
Objects
1 DNLIN A00-01Change DWC
Rebuild
Off
Check Consistency
On
Virtual Drive 0
RAID = 1
Units= MB
Size = 152146MB
DWC = Off
RA = On
Accept
SPAN = NO
ONLINE
Disk Write Cache Setting Of VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
Enabling DWC can improve the performance, but with the risk of data loss.
ASUS Z9PE-D16 Series
5-9
12. When finished setting the selected virtual drive configuration, select Accept
from the menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Virtual
VersionDrive(s)
A.10.09231523R
Configured
LD
RAID
Size
#Stripes
StripSzMENU Status
Easy Configuration
- ARRAY SELECTION
Management
0 Menu 1
148.580GB PORT
2 #
Configure
0 DNLIN A00-00
Initialize
Objects
1 DNLIN A00-01
Rebuild
Check Consistency
Virtual Drive 0
RAID = 1
Units= MB
Size = 152146MB
DWC = Off
RA = On
Accept
SPAN = NO
64 KB
ONLINE
Accept This VD Configuration And Go To Next VD
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Configure Esc-Quit
13. Follow step 2 to 12 to configure additional virtual drives.
14. Press <Esc> to finish RAID configuration. When prompted to save
configuration, select Yes from the menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Configuration Menu
Save Configuration?
Easy Configuration
Yes
New Configuration
Management Menu
No
View/Add Configuration
Configure
Clear Configuration
Initialize
Virtual Drive(s) Configured
Boot Drive
Objects
LD Select
RAID
Size
#Stripes
StripSz Status
Rebuild
Check Consistency
0
1
148.580GB
2
64 KB
ONLINE
Select Yes Or No
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
5-10
Chapter 5: RAID configuration
Using New Configuration
When a RAID set already exists, using the New Configuration command
erases the existing RAID configuration data. If you do not want to delete the
existing RAID set, use the View/Add Configuration command to view or create
another RAID configuration.
To create a RAID set using the New Configuration option
1.
From the Management Menu, select Configure > New Configuration, and
then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
Clear Existing Configuration And Start A New Configuration
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
2.
Follow step 2 to 9 of the previous section: Using Easy Configuration.
4.
Key-in the desired virtual drive size, and then press <Enter>.
3.
Select Size from the Virtual Drive menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Virtual
VersionDrive(s)
A.10.09231523R
Configured
LD
RAID
Size
#Stripes
StripSzMENU Status
Easy Configuration
- ARRAY SELECTION
Management
0 Menu 1
148.580GB PORT
2 #
Configure
0 DNLIN A00-00
Initialize
Objects
1 DNLIN A00-01
Rebuild
Check Consistency
Enter VD Size: 152146_
Virtual Drive 0
RAID = 1
Units= MB
Size = 152146MB
DWC = Off
RA = On
Accept
SPAN = NO
64 KB
ONLINE
Enter VD Size:
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
5.
Follow step 10 to 14 of the previous section: Using Easy Configuration to
create the RAID set.
ASUS Z9PE-D16 Series
5-11
5.2.2
Adding or viewing a RAID configuration
You can add a new RAID configuration or view an existing configuration using the
View/Add Configuration command.
Adding a new RAID configuration
To add a new RAID configuration:
1.
From the Management Menu, select Configure > View/Add Configuration,
and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
View/Add to The Existing Configuration
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
The ARRAY SELECTION MENU displays the available drives connected to
the SATA ports. Select the drive(s) you want to include in the RAID set, then
press <Space>. When selected, the drive indicator changes from READY to
ONLIN A[X]-[Y], where X is the array number, and Y is the drive number.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
View/Add Configuration - ARRAY SELECTION MENU
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Port # 2 DISK
PORT #
0 ONLIN A00-00
1 ONLIN A00-01
2 READY
3 READY
77247MB
HDS728080PLA380
PF20A60A
SPACE-Sel,ENTER-EndArray,F10-Configure,F2-Drive Info,F3-Virtual Drives,F4-HSP
The information of the selected hard disk drive displays at the bottom of the
screen.
3.
5-12
Follow step 3 to 12 of section 5.2.1 Creating a RAID set: Using Easy
Configuration to add a new RAID set.
Chapter 5: RAID configuration
5.2.3
Initializing the virtual drives
After creating the RAID set(s), you must initialize the virtual drives. You may
initialize the virtual drives of a RAID set(s) using the Initialize or Objects command
on the Management Menu.
Using the Initialize command
To initialize the virtual drive using the Initialize command
1.
From the Management Menu, select Initialize, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Initialize VD(s)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
The screen displays the available RAID set(s) and prompts you to select the
virtual drive to initialize. Use the arrow keys to select the virtual drive from the
Virtual Drive selection, and then press <Space>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
RAID
0
1
Virtual Drive(s) Configured
Size
#Stripes
StripSz
148.580GB
2
64 KB
Status
ONLINE
Virtual Drives
Virtual Drive 0
Select VD
SPACE-(De)Select, F10-Initialize
ASUS Z9PE-D16 Series
5-13
3.
Press <F10> to start initialization. When prompted, select Yes from the
Initialize? dialog box, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
RAID
0
1
Virtual Drive(s) Configured
Size
#Stripes
StripSz
148.580GB
2
Status
64 KB
ONLINE
Initialize?
Yes
No
Virtual Drives
Virtual Drive 0
Init Will Destroy Data On Selected VD(s)
SPACE-(De)Select, F10-Initialize
Initializing a virtual drive erases all data on the drive.
4.
A progress bar appears on screen. If desired, press <Esc> to abort
initialization. When initialization is completed, press <Esc>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Virtual Drive(s) Configured
Management Menu
LD
RAID
Size
#Stripes
StripSz
Configure
0 Init10Of VD
154494MB
4
64 KB
Is In Process
Initialize
Objects
VD 0 Initialization Complete. Press Esc..
Rebuild
Check Consistency
Status
ONLINE
¦ 100% Completed
Virtual Drives
Virtual Drive 0
SPACE-(De)Select, F10-Initialize
5-14
Chapter 5: RAID configuration
Using the Objects command
To initialize the virtual drives using the Objects command
1.
From the Management Menu, select Objects > Virtual Drive, and then
press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Objects
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Rebuild
Check Consistency
Change VD Parameters
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
Select the virtual drive to initialize from the Virtual Drives sub‑menu, and
then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Vitual Drive(1)
Virtual Drive 0
Objects
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Rebuild
Check Consistency
Select VD
Press ENTER To Select A VD, <Del> To Delete A VD
ASUS Z9PE-D16 Series
5-15
3.
Select Initialize from the pop-up menu, and then press <Enter> to start
initialization.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Vitual Drive(1)
Virtual Drive 0
Objects
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Vitual Drive(0)
Rebuild
Initialze
Check Consistency
Check Consistency
View/Update Parameters
Initilize VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
4.
When prompted, press the <Space> to select Yes from the Initialize? dialog
box, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Vitual Drive(1)
Virtual Drive 0
Objects
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Vitual Drive(0)
Rebuild
Initialze
Check Consistency
Initialize?
Check Consistency
Yes
View/Update Parameters
No
Init Will Destroy Data On Selected VD(s)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
5.
5-16
A progress bar appears on screen. If desired, press <Esc> to abort
initialization. When initialization is completed, press <Esc>.
Chapter 5: RAID configuration
5.2.4
Rebuilding failed drives
You can manually rebuild failed hard disk drives using the Rebuild command in the
Management Menu.
To rebuild a failed hard disk drive
1.
From the Management Menu, select Rebuild, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Rebuild PD(s)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
The PHYSICAL DRIVES SELECTION MENU displays the available drives
connected to the SATA ports. Select the drive you want to rebuild, and then
press <Space>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
REBUILD - PHYSICAL DRIVES SELECTION MENU
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Port # 1 DISK
PORT #
0 ONLIN A00-00
1 FAIL A00-01
77247MB
HDS728080PLA380
PF20A60A
SPACE-(De)Select,F10-Start Rebuild,F2-Drive Information,F3-View Virtual Drives
ASUS Z9PE-D16 Series
5-17
3.
After selecting the drive to rebuild, press <F10>. When prompted, press <Y>
to rebuild the drive.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
REBUILD - PHYSICAL DRIVES SELECTION MENU
Management Menu
PORT #
Configure
0 ONLIN A00-00
Initialize
Objects
1 RBLD A00-01
Rebuild
Check Consistency
Rebuilding
Of Drive Will Take A Few Minutes. Start Rebuilding Drive (Y/N)?
Port # 1 DISK
77247MB
HDS728080PLA380
PF20A60A
SPACE-(De)Select,F10-Start Rebuild,F2-Drive Information,F3-View Virtual Drives
4.
5-18
When rebuild is complete, press any key to continue.
Chapter 5: RAID configuration
5.2.5
Checking the drives for data consistency
You can check and verify the accuracy of data redundancy in the selected virtual
drive. The utility can automatically detect and/or detect and correct any differences
in data redundancy depending on the selected option in the Objects > Adapter
menu.
The Check Consistency command is available only for virtual drives included
in a RAID 1 or RAID 10 set.
Using the Check Consistency Command
To check data consistency using the Check Consistency command
1.
From the Management Menu, select Check Consistency, and then press
<Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
CC Of VD(s)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
The screen displays the available RAID set(s) and prompts you to select
the virtual drive to check. Press <Space> to select the virtual drive from the
Virtual Drive sub-menu, and then press <F10>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
RAID
0
1
Virtual Drive(s) Configured
Size
#Stripes
StripSz
148.580GB
2
64 KB
Status
ONLINE
Virtual Drives
Virtual Drive 0
Select VD
SPACE-(De)Select,
ASUS Z9PE-D16 Series
F10-Check Consistency
5-19
3.
When prompted, use the arrow keys to select Yes from the Consistency
Check? dialog box, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
0
Virtual Drive(s) Configured
RAID
Size
#Stripes
StripSz
10 154494MB
4
64 KB
Yes
No
Status
ONLINE
Consistency Check?
Virtual Drives
Virtual Drive 0
Select VD
SPACE-(De)Select,
F10-Check Consistency
A progress bar appears on screen.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Virtual Drive(s) Configured
Management Menu
LD
RAID
Size
#Stripes
StripSz
Configure
0
10
154494MB
64 KB
CC Under
Process 4
Initialize
Objects
VD 0 Consistency Check. Press Esc to Abort.
Rebuild
Check Consistency
Status
ONLINE
¦ 85 % Completed
Virtual Drives
Virtual Drive 0
The Data On The Drives Is Inconsistency. Repair Done!
SPACE-(De)Select,
4.
5-20
F10-Check Consistency
While checking the disk consistency, press <Esc> to display the following
options.
• Stop
- Stops the consistency check. The utility stores the
percentage of disk checked, and when you restart checking,
it continues from the last percentage completed rather than
from zero percent.
• Continue- Continues the consistency check.
• Abort
5.
When checking is complete, press any key to continue.
- Aborts the consistency check. When you restart checking, it
continues from zero percent.
Chapter 5: RAID configuration
Using the Objects command
To check data consistency using the Objects command
1.
2.
3.
4.
5.
From the Management Menu, select Objects, and then select Virtual Drive
from the sub-menu.
Use the arrow keys to select the virtual drive you want to check, and then
press <Enter>.
Select Check Consistency from the pop-up menu, and then press <Enter>.
When prompted, use the arrow keys to select Yes from the dialog box to
check the drive.
When checking is complete, press any key to continue.
ASUS Z9PE-D16 Series
5-21
5.2.6
Deleting a RAID configuration
To delete a RAID configuration
1.
From the Management Menu, select Configure > Clear Configuration, and
then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
Clear Existing Configuration
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
When prompted, use the arrow keys to select Yes from the Clear
Configuration? dialog box, and then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
Clear Configuration?
View/Add Configuration
Configure
Yes
Clear Configuration
Initialize
No
Select Boot Drive
Objects
Rebuild
Check Consistency
Clear Existing Configuration
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
3.
5-22
The utility clears all the current array(s).
Press any key to continue.
Chapter 5: RAID configuration
5.2.7
Selecting the boot drive from a RAID set
You must have created a new RAID configuration before you can select the
boot drive from a RAID set. See section 5.2.1 Creating a RAID set: Using New
Configuration for details.
To select the boot drive from a RAID set
1.
From the Management Menu, select Configure > Select Boot Drive, and
then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
Select A Boot VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
When prompted, use the arrow keys to select the bootable virtual drive from
the list, then press <Enter>.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Bootable VDs(1):Current Boot VD(0)
Configuration
BootMenu
Drive 0
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
Select A Boot VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
3.
The virtual drive is selected as boot drive. Press any key to continue.
ASUS Z9PE-D16 Series
5-23
5.2.8
Enabling WriteCache
You may manually enable the RAID controller’s WriteCache option after creating a
RAID set to improve the data transmission performance.
When you enable WriteCache, you may lose data when a power interruption occurs
while transmitting or exchanging data among the drives.
The WriteCache function is recommended for RAID 1 and RAID 10 sets.
To enable WriteCache
1.
2.
From the Management Menu, select Objects > Adapter, select an existing
adapter, and then press <Enter> to display the adapter properties.
Select Disk WC, and then press <Enter> to turn on the option.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Adapter 0
Rebuild Rate = 30
ObjectsChk Const Rate = 30
Management Menu
Adapter
FGI Rate
= 30
Configure
Virtual Drive BGI Rate
= 30
Initialize
Physical DriveDisk WC
= Off
Objects
Read Ahead
= On
Rebuild
Bios State
= Enable
Check Consistency
Cont On Error = Yes
Fast Init
= Enable
Auto Rebuild = On
Auto Resume
= Enable
Disk Coercion = 1GB
Factory Default
Disk Write Cache - Off(Write Through) or On(Write Back)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
3.
4.
From the Management Menu, select Objects > Virtual Drive, select an
existing adapter and press <Enter>. Select View/Update Parameters and
press <Enter> to display the adapter properties.
Select Disk WC, and then press <Enter> to turn on the option.
LSI Software RAID Configuration Utility Ver C.05 Sep 17, 2010
BIOS Version A.10.09231523R
Virtual Drive
RAID
= 0
Objects
Size
= 148.580GB
Management Menu
Adapter
Stripe Size = 64KB
Configure
Virtual Drive
#Stripes
= 2
Initialize
Physical Drive
State
= OPTIMAL
Objects
Spans
= 1
Rebuild
Disk WC
= On
Check Consistency
Read Ahead
= On
Disk Write Cache Setting of VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
5.
5-24
When finished, press any key to continue.
Chapter 5: RAID configuration
5.3Intel® Rapid Storage Technology
enterprise SCU/SATA Option ROM
Utility
The Intel® Rapid Storage Technology enterprise SCU / SATA Option ROM utility
allows you to create RAID 0, RAID 1, RAID 10 (RAID 1+0), and RAID 5 set(s)
from Serial ATA hard disk drives that are connected to the Serial ATA connectors
supported by the Southbridge.
You can create RAID mode by use of onboard AHCI SATA ports.
To use onboard SATA ports:
1. Install all the Serial ATA hard disk drives.
2. Turning on the system. During POST, press,Del. to enter BIOS. Go to
Advanced Menu > PCH SATA Configuration > SATA Mode, then press
<Enter>.
3. Set SATA Mode to RAID Mode and save, then reboot system.
4. During POST, press <Ctrl+I> to display the utility main menu.
To use SCU SATA ports:
1.
Install all the hard disk drives.
3.
Confirm all the SATA hard disk drives you installed are correctly displayed,
then reboot system.
2.
4.
Turn on the system.
During POST, press <Ctrl+I> to display the utility main menu.
ASUS Z9PE-D16 Series
5-25
To enter the Intel® Rapid Storage Technology enterprise SCU option ROM utility:
1.
Install all the Serial ATA hard disk drives.
3.
During POST, press <Ctrl+I> to display the utility main menu.
2.
Turn on the system.
Intel(R) Rapid Storage Technology enterprise - SCU Option ROM - 3.0.0.1104
Copyright(C) 2003-11 Intel Corporation. All Rights Reserved.
[ MAIN MENU ]
1. Create RAID Volume
2. Delete RAID Volume
3. Reset Disks to Non-RAID
4. Exit
[ DISK/VOLUME INFORMATION ]
RAID Volumes:
None defined.
Physical Disks:
ID
Drive Model
0
ST3300656SS
1
ST3300656SS
2
ST3300656SS
3
ST3300656SS
[↑↓]-Select
Serial #
HWAS0000991753TR
37VN00009846RAJ1
397600009846UEDY
GWC50000991756G6
[ESC]-Exit
Size Type/Status(Vol ID)
279.3GB
Non-RAID Disk
279.3GB
Non-RAID Disk
279.3GB
Non-RAID Disk
279.3GB
Non-RAID Disk
[ENTER]-Select Menu
The navigation keys at the bottom of the screen allow you to move through
the menus and select the menu options.
The RAID BIOS setup screThe RAID BIOS setup screens shown in this section
are for reference only and may not exactly match the items on your screen.
The utility supports maximum four hard disk drives for RAID configuration.
5-26
Chapter 5: RAID configuration
5.3.1
Creating a RAID set
To create a RAID set
1.
From the utility main menu, select 1. Create RAID Volume and press
<Enter>. The following screen appears.
Intel(R) Rapid Storage Technology enterprise - SCU Option ROM - 3.0.0.1104
Copyright(C) 2003-11 Intel Corporation. All Rights Reserved.
[ CREATE VOLUME MENU ]
Name:
RAID Level:
Disks:
Strip Size:
Capacity:
Volume0
RAID0(Stripe)
Select Disks
128KB
0.0
GB
Create Volume
[ HELP ]
Enter a unique volume name that has no special characters and is
16 characters or less.
[↑↓]Change
2.
3.
4.
[TAB]-Next
[ESC]-Previous Menu
[ENTER]-Select
Enter a name for the RAID set and press <Enter>.
When the RAID Level item is selected, press the up/down arrow key to select
a RAID level to create, and then press <Enter>.
When the Disks item is selected, press <Enter> to select the hard disk drives
you want to include in the RAID set. The SELECT DISKS screen appears.
[ SELECT DISKS ]
Port
0
1
2
3
Drive Model
ST3300656SS
ST3300656SS
ST3300656SS
ST3300656SS
Serial #
HWAS0000991753TR
37VN00009846RAJ1
397600009846UEDY
GWC50000991756G6
Size
279.3GB
279.3GB
279.3GB
279.3GB
Status
Non-RAID
Non-RAID
Non-RAID
Non-RAID
Disk
Disk
Disk
Disk
Select 2 to 6 disks to use in creating the volume.
[↑↓]-Prev/Next [SPACE]-SelectDisk [ENTER]-Done
5.
Use the up/down arrow key to select a drive, and then press <Space>
to select. A small triangle marks the selected drive. Press <Enter> after
completing your selection.
ASUS Z9PE-D16 Series
5-27
6.
Use the up/down arrow keys to select the stripe size for the RAID array (for
RAID 0, 10 and 5 only), and then press <Enter>. The available stripe size
values range from 4 KB to 128 KB. The following are typical values:
RAID 0: 128KB
RAID 10: 64KB
RAID 5: 64KB
We recommend a lower stripe size for server systems, and a higher stripe size
for multimedia computer systems used mainly for audio and video editing.
7.
8.
When the Capacity item is selected, enter the RAID volume capacity that you
want and press <Enter>. The default value indicates the maximum allowed
capacity.
When the Create Volume item is selected, press <Enter>. The following
warning message appears.
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
9.
Press <Y> to create the RAID volume and return to the main menu, or <N> to
go back to the CREATE VOLUME menu.
5.3.2
Creating a Recovery set
To create a recovery set:
1.
From the utility main menu, select 1. Create RAID Volume and press
<Enter>. The following screen appears.
Intel(R) Rapid Storage Technology enterprise - SCU Option ROM - 3.0.0.1104
Copyright(C) 2003-11 Intel Corporation. All Rights Reserved.
[ CREATE VOLUME MENU ]
Name:
RAID Level:
Disks:
Strip Size:
Capacity:
Sync:
Volume0
RAID0(Stripe)
Select Disks
128KB
0.0
GB
N/A
Create Volume
[ HELP ]
Enter a unique volume name that has no special characters and is
16 characters or less.
[↑↓]Change
5-28
[TAB]-Next
[ESC]-Previous Menu
[ENTER]-Select
Chapter 5: RAID configuration
2.
3.
4.
Enter a name for the recovery set and press <Enter>.
When the RAID Level item is selected, press the up/down arrow keys to
select Recovery, and then press <Enter>.
When the Disks item is selected, press <Enter> to select the hard disk drives
you want to include in the recovery set. The SELECT DISKS screen appears.
[ SELECT DISKS ]
Port
0
1
2
3
Drive Model
ST3300656SS
ST3300656SS
ST3300656SS
ST3300656SS
Serial #
HWAS0000991753TR
37VN00009846RAJ1
397600009846UEDY
GWC50000991756G6
Size
279.3GB
279.3GB
279.3GB
279.3GB
Status
Non-RAID
Non-RAID
Non-RAID
Non-RAID
Disk
Disk
Disk
Disk
Select 1 Master and 1 Recovery disk to create volume.
[[↑↓]-Prev/Next [TAB]-(M)aster [SPACE]-(R)ecovery [ENTER]-Done
5.
6.
7.
Use the up/down arrow keys to select a drive, press <TAB> to select a Master
disk, and then press <SPACE> to select a Recovery disk. A small triangle
marks the selected drive. Press <Enter> after completing your selection.
When the Sync item is selected, use the up/down arrow keys to select a sync
option that you want and press <Enter>.
When the Create Volume item is selected, press <Enter>. The following
warning message appears.
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
8.
Press <Y> to create the recovery set and return to the main menu, or <N> to
go back to the CREATE VOLUME menu.
If a recovery set is created, you cannot add more RAID sets even when you
have more non-RAID disks installed in your system.
ASUS Z9PE-D16 Series
5-29
5.3.3
Deleting a RAID set
Take caution when deleting a RAID set. You will lose all data on the hard disk
drives when you delete a RAID set.
To delete a RAID set:
1.
From the utility main menu, select 2. Delete RAID Volume and press
<Enter>. The following screen appears.
Intel(R) Rapid Storage Technology enterprise - SCU Option ROM - 3.0.0.1104
Copyright(C) 2003-11 Intel Corporation. All Rights Reserved.
[ DELETE VOLUME MENU ]
Name
Volume0
Level
RAID0(Stripe)
Drives
2
Capacity
298.0GB
Status
Normal
Bootable
Yes
[ HELP ]
Deleting a volume will reset the disks to non-RAID.
WARNING: ALL DISK DATA WILL BE DELETED.
(This does not apply to Recovery volumes)
[↑↓]-Select
2.
[ESC]-Previous Menu
[DEL]-Delete Volume
Use the up/down arrow keys to select the RAID set you want to delete, and
then press <Del>. The following warning message appears.
[ DELETE VOLUME VERIFICATION ]
ALL DATA IN THE VOLUME WILL BE LOST!
(This does not apply to Recovery volumes)
Are you sure you want to delete volume “Volume0”? (Y/N):
3.
5-30
Press <Y> to delete the RAID set and return to the utility main menu, or press
<N> to return to the DELETE VOLUME menu.
Chapter 5: RAID configuration
5.3.4
Resetting disks to Non-RAID
Take caution before you reset a RAID volume hard disk drive to non-RAID.
Resetting a RAID volume hard disk drive deletes all internal RAID structure on
the drive.
To reset a RAID set hard disk drive:
1.
From the utility main menu, select 3. Reset Disks to Non-RAID and press
<Enter>. The following screen appears.
[ RESET RAID DATA ]
Resetting RAID disk will remove its RAID structures
and revert it to a non-RAID disk.
WARNING: Resetting a disk causes all data on the disk to be lost.
(This does not apply to Recovery volumes)
Port Drive Model
0
ST3300656SS
1
ST3300656SS
Serial #
HWAS0000991753TR
37VN00009846RAJ1
Size
279.3GB
279.3GB
Status
Member Disk
Member Disk
Select the disks that should be reset.
[↑↓]-Previous/Next
2.
3.
4.
[SPACE]-Selects [ENTER]-Selection Complete
Use the up/down arrow keys to select the RAID set drive(s) you want to reset,
and then press <Space> to select.
Press <Enter> to reset the RAID set drive(s). A confirmation message
appears.
Press <Y> to reset the drive(s) or press <N> to return to the utility main
menu.
ASUS Z9PE-D16 Series
5-31
5.3.5
Exiting the Intel® Rapid Storage Technology utility
To exit the utility:
1.
From the utility main menu, select 4. Exit, and then press <Enter>. The
following warning message appears.
[ CONFIRM EXIT ]
Are you sure you want to exit? (Y/N):
2.
Press <Y> to exit or press <N> to return to the utility main menu.
5.3.6
Rebuilding the RAID
This option is only for the RAID 1 set.
Rebuilding the RAID with other non-RAID disk
If any of the SATA hard disk drives included in the RAID 1 array failed, the system
displays the status of the RAID volume as “Degraded” during POST. You can
rebuild the RAID array with other installed non-RAID disks.
To rebuild the RAID with other non-RAID disk:
1.
2.
At the prompt, press <Ctrl> + <I> to enter the Intel Rapid Storage Technology
option ROM utility.
If there is a non-RAID SATA Hard Disk available, the utility will prompt to
rebuild the RAID. Press <Enter>, and then use up/down arrow keys to select
the destination disk or press <ESC> to exit.
[ DEGRADED VOLUME DETECTED ]
"Degraded" volume and disk available for rebuilding detected. Selecting
a disk initiates a rebuild. Rebuild completes in the operating system.
Select the port of destination disk for rebuilding (ESC to exit):
Port Drive Model
Serial #
Size
X
XXXXXXXXXXX
XXXXXXXX
XX.XGB
[↑↓]-Previous/Next
[ENTER]-Select
[ESC]-Exit
Select a destination disk with the same size as the original hard disk.
5-32
Chapter 5: RAID configuration
3.
The utility immediately starts rebuilding after the disk is selected. The status
of the degraded RAID volume is changed to “Rebuild”.
Intel(R) Rapid Storage Technology enterprise - SCU Option ROM - 3.0.0.1104
Copyright(C) 2003-11 Intel Corporation. All Rights Reserved.
[ MAIN MENU ]
1. Create RAID Volume
2. Delete RAID Volume
3. Reset Disks to Non-RAID
4. Exit
[ DISK/VOLUME INFORMATION ]
RAID Volumes:
ID
Name
0
Volume0
Physical Devices:
Port Drive Model
1
ST3160812AS
2
ST3160812AS
5.
6.
7.
Strip
N/A
Serial #
9LS0F4HL
3LS0JYL8
Size
149.0GB
Size
149.0GB
149.0GB
* = Data is Encrypted
Status
Bootable
Rebuild
Yes
Type/Status(Vol ID)
Member Disk(0)
Member Disk(0)
Volumes with “Rebuild” status will be rebuilt within the operating system.
[↑↓]-Select
4.
Level
RAID1(Mirror)
[ESC]-Exit
[ENTER]-Select Menu
Exit Intel Rapid Storage Technology and reboot the system.
Under Microsoft® Windows OS, select Start > Programs > Intel Rapid
Storage > Intel Rapid Storage Console or click the Intel Rapid Storage
Technology tray icon to load the Intel Rapid Storage Manager utility.
From the View menu, select Advanced Mode to display the details of the
Intel Rapid Storage Console.
From the Volumes view option, select RAID volume to view the rebuilding
status. When finished, the status is changed to “Normal”.
Rebuilding the RAID with a new hard disk
If any of the SATA hard disk drives included in the RAID array failed, the system
displays the status of the RAID volume as “Degraded” during POST. You may
replace the disk drive and rebuild the RAID array.
To rebuild the RAID with a new hard disk:
1.
Remove the failed SATA hard disk and install a new SATA hard disk of the
same specification into the same SATA Port.
Select a destination disk with the same size as the original hard disk.
2.
Reboot the system and then follow the steps in section Rebuilding the RAID
with other non-RAID disk.
ASUS Z9PE-D16 Series
5-33
5.3.7
Setting the Boot array in the BIOS Setup Utility
You can set the boot priority sequence in the BIOS for your RAID arrays when
creating multi-RAID using the Intel® Rapid Storage Technology.
To set the boot array in the BIOS:
Set at least one of the arrays bootable to boot from the hard disk.
1.
2.
3.
4.
5.
5-34
Reboot the system and press <Del> to enter the BIOS setup utility during
POST.
Go to the Boot menu and select the boot option priority.
Use up/down arrow keys to select the boot priority and press <Enter>. See
section 4.7 Boot menu for details.
From the Exit menu, select Save Changes & Exit, then press <Enter>.
When the confirmation window appears, select Yes, then press <Enter>.
Chapter 5: RAID configuration
5.4Intel® Rapid Storage Technology
enterprise Utility (Windows)
The Intel® Rapid Storage Technology enterprise utility allows you to create RAID 0,
RAID 1, RAID 10 (RAID 1+0), and RAID 5 set(s) from Serial ATA hard disk drives
that are connected to the Serial ATA connectors supported by the Southbridge.
To enter the Intel® Rapid Storage Technology enterprise SCU option ROM utility
under Windows operating system:
1.
2.
Turn on the system to windows desktop.
Click the Intel® Rapid Storage Technology enterprise icon to display the
main menu.
Your storage system is configured for data protection, increased performance and
optimal data storage capacity. You can further optimize your storage system by
creating additional volumes.
You can click Rescan to re-scan any attached hard disks.
ASUS Z9PE-D16 Series
5-35
5.4.1
Creating a RAID set
To create a RAID set
1.
From the utility main menu, select Create Volume and select volume type.
3.
Enter a name for the RAID set, then select the array disks.
5.
Then click Next.
2.
4.
5-36
Then click Next.
Select Volume Size tab, you can drag the bar to decide the volume size.
•
If you hard disk with existing data and you don’t want to keep data from one
of the selected disks, choose NO in next column (If displayed).
•
If you want to Enable volume write-back cache or Initialize volume, you
can click Advanced tab to slelect.
Chapter 5: RAID configuration
6.
Confirm volume creation, than click Create Volume to continue.
This process could take a while depending on the number and size of the disks.
You can contuine using other applications during this time.
When display Volume Ceation Complete message, you can click OK to finish.
You still need to partition your new volume using Windows Disk Management
before adding any data.
When you are finished, you will see the following screen in Volumes field and you
can change related items in the Volume Properties field.
ASUS Z9PE-D16 Series
5-37
5.4.2
Change Volume Type
When you are finished to create a RAID set, you can view or change related items
in the Volume Properties field.
According to the following steps to change the type in Volume Properties:
1.
Click the SAS array items you want to change in Volumes field.
3.
You can change the Name, Select the new volume type, and Select
additional disks to include in the new volume if needed.
2
4.
From the Volume Properties field, select Type:RAID 1 Change type.
Then select the Data stripe size for the RAID array (for RAID 0, 10 and 5
only), and then click OK. The available stripe size values range from 4 KB to
128 KB. The following are typical values:
RAID 0: 128KB
RAID 10: 64KB
RAID 5: 64KB
We recommend a lower stripe size for server systems, and a higher stripe size
for multimedia computer systems used mainly for audio and video editing.
5-38
Chapter 5: RAID configuration
5.4.3
Delete volume
Take caution when deleting a volume. You will lose all data on the hard disk
drives.Back up data before continuing.
To delete a volume:
1.
From the utility main menu, select the volume (exp. Volume_0000) in
Volumes field you want to delete.
2.
Then select Delete volume in Volume Properties field. The following screen
appears.
3.
Click Yes to delete the volume and return to the utility main menu, or click No
to return to the main menu.
ASUS Z9PE-D16 Series
5-39
5.4.4
Preferences
System Preferences
Allow you set to show the notification area icon and show system information, warning, or
errors here.
E-Mail Preferences
Allow you set to sent e-mail of the following events:
Storage system information
Storage system warnings
Storage system errors
5-40
Chapter 5: RAID configuration
This chapter provides the instructions
for installing the necessary drivers for
different system components.
Chapter 6:
6
Driver
installation
Chapter summary
6.1
6
RAID driver installation................................................................ 6-3
6.2Intel® chipset device software installation................................ 6-15
6.3Intel@ Network Connections Software installation.................. 6-17
6.4
VGA driver installation............................................................... 6-20
6.6
Microsoft .NET Framework 3.5 SP1........................................... 6-24
6.5Intel® C600 Series Chipset SCU SATA RAID Driver.................. 6-23
6.7Intel® Rapid Storage Technology enterprise 3.0 installation.. 6-25
6.8Intel® I350 Gigabit Adapters Driver installation........................ 6-28
6.9Management applications and utilities installation................. 6-32
ASUS Z9PE-D16 Series
6.1
RAID driver installation
After creating the RAID sets for your server system, you are now ready to install
an operating system to the independent hard disk drive or bootable array. This part
provides the instructions on how to install the RAID controller drivers during OS
installation.
6.1.1
Creating a RAID driver disk
The system does not include a floppy drive. You have to use a USB floppy drive
when creating a SATA RAID driver disk.
If you have created RAID sets with the LSI Software RAID configuration utility,
the boot priority of the SATA optical disk drive has to be manually adjusted.
Otherwise, the system will not boot from the connected SATA ODD.
A floppy disk with the RAID driver is required when installing Windows® XP / Server
2003 or Linux operating system on a hard disk drive that is included in a RAID set.
You can create a RAID driver disk in DOS (using the Makedisk application in the
support DVD).
To create a RAID driver disk in DOS environment
1.
Place the motherboard support DVD in the optical drive.
3.
Select the optical drive as the first boot priority to boot from the support DVD.
Save your changes, and then exit the BIOS Setup.
2.
4.
Restart the computer, and then enter the BIOS Setup.
Restart the computer. The Makedisk menu appears.
Create Driver Diskette Menu
C60x INTEL RAID Driver
Write DMI
FreeDOS command prompt
5.
Use the arrow keys to select the type of RAID driver disk you want to create
and press <Enter> to enter the sub-menu.
C60x INTEL RAID Driver
Windows
Windows
Windows
Windows
Back
Exit
32
64
32
64
ASUS Z9PE-D16 Series
C600
bit
bit
bit
bit
INTEL RAID Driver
(AHCI / AHCI RAID)
(AHCI / AHCI RAID)
(SCU RAID)
(SCU RAID)
6-3
LSI 2008 SAS2 Driver
LSI 2008 SAS2 Driver
Windows XP 32 bit
Windows XP 64 bit
Windows Server 2003 32 bit
Windows Server 2003 64 bit
Windows Vista 32 bit
Windows Vista 64 bit
Windows Server 2008 32 bit
Windows Server 2008 64 bit
Windows 7 32 bit
Windows 7 64 bit
Windows Server 2008 R2 64 bit
RHEL 4 UP7 32 bit
RHEL 4 UP7 64 bit
RHEL 4 UP8 32 bit
RHEL 4 UP8 64 bit
Back
Exit
6.
7.
8.
Locate the RAID driver and place a blank, high-density floppy disk to the
floppy disk drive.
Press <Enter>.
Follow screen instructions to create the driver disk.
To create a RAID driver disk in Windows® environment
1. Start Windows®.
2. Place the motherboard support DVD into the optical drive.
3. Go to the Make disk menu, and then select the type of RAID driver disk you
want to create.
4. Insert a floppy disk into the USB floppy disk drive.
5. Follow succeeding screen instructions to complete the process.
Write-protect the floppy disk to avoid computer virus infection.
To create a RAID driver disk in Red Hat® Enterprise Linux server environment
1.
2.
Insert a blank formatted high-density floppy disk to the USB floppy disk drive.
Type dd if=XXX.img of=/dev/fd0 to decompress the file into the floppy
disk from the following path in the support DVD:
For LSI MegaRAID Driver
\Drivers\C60x LSI RAID\Driver\makedisk\Linux
3. Eject the floppy disk.
6-4
Chapter 6: Driver installation
6.1.2
Installing the RAID controller driver
During Windows® Server 2008 OS installation
To install the RAID controller driver when installing Windows® Server 2008 OS
1.
2.
3.
Boot the computer using the Windows® Server 2008 OS installation disc.
Follow the screen instructions to start installing Windows Server 2008.
When prompted to choose a type of installation, click Custom (advanced).
Click Load Driver.
ASUS Z9PE-D16 Series
6-5
4.
A message appears, reminding you to insert the installation media containing
the driver of the RAID controller driver. If you have only one optical drive
installed in your system, eject the Windows OS installation disc and replace
with the motherboard Support DVD into the optical drive. Click Browse to
continue.
5.
Locate the driver in the corresponding folder of the Support DVD, and then
click OK to continue.
6.
6-6
Select the RAID controller driver you need from the list and click Next.
7.
When the system finishes loading the RAID driver, replace the motherboard
Support DVD with the Windows Server installation disc. Select the drive to
install Windows and click Next.
8.
Setup then proceeds with the OS installation. Follow screen instructions to
continue.
Chapter 6: Driver installation
Red Hat® Enterprise Linux OS 5.6
To install the LSI MegaRAID controller driver when installing��������
Red Hat® Enterprise
OS:
1.
2.
Boot the system from the Red Hat® OS installation CD.
At the boot:, type linux dd noprobe=ata1 noprobe=ata2..., then
press <Enter>.
The number of ata varies with the hard disk drive number you have when
building a RAID set. For example, if you want to build a RAID set with 6 hard
disk drives, type command line: linux dd noprobe=ata1 noprobe=ata2
noprobe=ata3 noprobe=ata4 noprobe=ata5 noprobe=ata6.
- To install or upgrade in graphical mode, press the <ENTER> key.
- To install or upgrade in text mode, type: linux text <ENTER>.
- Use the function keys listed below for more information.
[F1-Main] [F2-Options] [F3-General] [F4-Kernel] [F5-Rescue]
boot: linux dd noprobe=ata1 noprobe=ata2
3.
Select Yes using the <Tab> key when asked if you have the driver disk, then
press <Enter>.
Main Menu
Do you have a driver disk?
Yes
4.
No
Insert the Red Hat® Enterprise RAID driver disk to the USB floppy disk drive,
select OK, then press <Enter>.
Insert Driver Disk
Insert your driver disk into /dev/fd0
and press “OK” to continue.
OK
Back
The drivers for the RAID card are installed to the system.
ASUS Z9PE-D16 Series
6-7
5.
When asked if you will load additional RAID controller drivers, select No, then
press <Enter>.
More Driver Disks?
Do you wish to load any more
driver disks?
Yes
6.
6-8
No
Follow the onscreen instructions to finish the OS installation.
7.
When the installation is completed, DO NOT click Reboot. Press <Ctrl>
+ <Alt> + <F2> to switch to the command-line interface from graphic user
interface.
8.
Type the following commands when using a Legacy floppy.
mkdir /mnt/driver
mount /dev/fd0 /mnt/driver
cd /mnt/driver
sh replace_ahci.sh
reboot
Chapter 6: Driver installation
Red Hat® Enterprise Linux OS 6.1
To install the LSI MegaRAID controller driver when installing��������
Red Hat® Enterprise
OS:
1.
Boot the system from the Red Hat® OS installation CD.
3.
While booting from DVD, press <ESC> to give the third party driver.
Enter the following command at the boot: Linux dd blacklist=isci
blacklist=ahci nodmraid, then press <ENTER>.
2.
Press <Tab> to edit options.
ASUS Z9PE-D16 Series
6-9
4.
Select Yes using the <Tab> key when asked if you have the driver disk, then
press <Enter>.
Main Menu
Do you have a driver disk?
Yes
No
5 . You have multiple devices which could serve as source for a driver disk.
Choose one you like to use and select OK, then press <Enter>.
Driver Disk Sou8rce
You have multiple devices which could
serve as source for a driver disk.
Which would you like to use?
sdc
sdd
sdb
sr0
OK
6-10
Cancel
Chapter 6: Driver installation
6.
Insert the Red Hat® Enterprise RAID driver disk to the USB floppy disk drive,
select OK, then press <Enter>.
Insert Driver Disk
Insert your driver disk into /dev/sdb
and press “OK” to continue.
OK
Back
The drivers for the RAID card are installed to the system.
7.
When asked if you will load additional RAID controller drivers, select No, then
press <Enter>.
More Driver Disks?
Do you wish to load any more
driver disks?
Yes
8.
No
Follow the onscreen instructions to finish the OS installation.
ASUS Z9PE-D16 Series
6-11
Preparing the Linux Driver
Ensure that there is another computer with a Linux-based OS to create the RAID driver. When
creating the RAID driver, you may refer to the examples below which uses a 64bit SUSE
Linux system to create a 64bit RAID driver for SUSE11 sp1.
1. Copy the image file into the Linux system.
Example: megasr-15.00.0120.2012-1-sles11-ga-x86_64.img
2.
3.
Mount the image file into the image folder using this command format:
mount -oloop [image file name] image
Example: mount -oloop megasr-15-15.00.0120.2012-1-sles11ga-x86__64.img image
4.
Copy the contents of the image directory, labeled as 01, into a FAT32 USB
drive.
5.
Rename the 01 folder to CD Image.
6-12
Create a folder.
Example: image
Chapter 6: Driver installation
Installing SUSE 11 Linux OS
To install the LSI MegaRAID controller driver when installing SUSE Linux Enterprise
Server OS:
1.
Boot the system from the SUSE OS installation CD.
3.
Press <F6>, then select Yes from the menu. Press <Enter>.
2.
Use the arrow keys to select Installation from the Boot Options menu.
ASUS Z9PE-D16 Series
6-13
4.
Use the USB drive to provide the third-party driver during the OS installation.
Type the command brokenmodules=ahci in Boot Options field, and press
<Enter>.
5.
When below screen appears, select the USB floppy disk drive (sda) as the
driver update medium. Select OK, then press <Enter>.
Please choose the Driver Update medium.
sda: USB Floppy
other device
OK
6.
6-14
Back
Select Back and follow the onscreen instructions to finish the installation.
Chapter 6: Driver installation
6.2Intel® chipset device software
installation
This section provides the instructions on how to install the Intel® chipset device
software on the system.
You need to manually install the Intel® chipset device software on a Windows
operating system.
To install the Intel® chipset device software:
1.
2.
Restart the computer, and then log on with Administrator privileges.
Insert the motherboard/system support DVD to the optical drive. The support
DVD automatically displays the Drivers menu if Autorun is enabled in your
computer.
If Autorun is NOT enabled in your computer, browse the contents of the support
DVD to locate the file ASSETUP.EXE from the BIN folder. Double-click the
ASSETUP.EXE to run the support DVD.
3.
Click the item Intel Chipset Device Software from the menu.
4.
The Intel(R) Chipset Device Software window appears. Click Next to start
installation.
ASUS Z9PE-D16 Series
6-15
6-16
5.
Select Yes to accept the terms of the License Agreement and continue the
process.
6.
Read the Readme File Information and press Next to continue the
installation.
7.
Toggle Yes, I want to restart the computer npw and click Finish to
complete the setup process.
Chapter 6: Driver installation
6.3Intel@ Network Connections Software
installation
This section provides the instructions on how to install the Intel® Network
Connections Software on the system.
You need to manually install the Intel® Network Connections Software on a
Windows® operating system. To install the Intel® Network Connections Software:
1.
2.
Restart the computer, and then log on with Administrator privileges.
Insert the motherboard/system support DVD to the optical drive. The support
DVD automatically displays the Drivers menu if Autorun is enabled in your
computer.
•
Windows® automatically detects the LAN controllers and displays a New
Hardware Found window. Click Cancel to close this window.
•
If Autorun is NOT enabled in your computer, browse the contents of the
support DVD to locate the file ASSETUP.EXE from the BIN folder. Doubleclick the ASSETUP.EXE to run the DVD.
3.
Click the Intel® Network Connections Software to begin installation.
4.
Click Install Drivers and Software option to begin installation.
ASUS Z9PE-D16 Series
6-17
6-18
5.
Click Next when the Intel(R) Network Connections–InstallShield Wizard
window appears.
6.
Toggle I accept the terms in the license agreement and click Next to
continue.
7.
Click the Intel(R) PROSet for Windows Device Manager box, and then click
Next to start the installation.
Chapter 6: Driver installation
8.
Follow the screen instructions to complete installation.
9.
When finished, press Finish to continue.
ASUS Z9PE-D16 Series
6-19
6.4
VGA driver installation
This section provides the instructions on how to install the ASPEED Video
Graphics Adapter (VGA) driver.
You need to manually install the ASPEED VGA driver on a Windows® operating
system.
To install the ASPEED VGA driver:
1.
2.
Restart the computer, and then log on with Administrator privileges.
Insert the motherboard/system support DVD to the optical drive. The support
DVD automatically displays the Drivers menu if Autorun is enabled in your
computer.
If Autorun is NOT enabled in your computer, browse the contents of the support
DVD to locate the file ASSETUP.EXE from the BIN folder. Double-click the
ASSETUP.EXE to run the support DVD.
6-20
3.
Click the ASPEED AST2300 Display Driver to begin installation.
4.
When the ASPEED Graphics installation wizard appears, click Next to start
the installation.
Chapter 6: Driver installation
5.
Toggle I accept the terms in the license agreement and click Next to
continue.
6.
Enter the user information and click Next to continue.
7.
Select a setup type and click Next to continue.
ASUS Z9PE-D16 Series
6-21
6-22
8.
Click Install to start driver installation.
9.
When the installation completes, click Finish to restart your computer before
using the program.
Chapter 6: Driver installation
6.5Intel® C600 Series Chipset SCU SATA
RAID Driver
This section provides the instructions on how to install the Intel® C600 Series
Chipset Driver on the system.
You need to manually install the Intel® C600 Series Chipset SCU SATA RAID Driver
on a Windows operating system.
To install the drivers:
1.
2.
Restart the computer, and then log on with Administrator privileges.
Insert the motherboard/system support DVD to the optical drive. The support
DVD automatically displays the Drivers menu if Autorun is enabled in your
computer.
If Autorun is NOT enabled in your computer, browse the contents of the support
DVD to locate the file ASSETUP.EXE from the BIN folder. Double-click the
ASSETUP.EXE to run the support DVD.
3.
Click the item Intel® C600 Series Chipset SCU SATA RAID Driver from the
menu, and then follow the onscreen instructions to complete the installation.
ASUS Z9PE-D16 Series
6-23
6.6
Microsoft .NET Framework 3.5 SP1
This section provides the instructions on how to install the Microsoft .NET
Framework 3.5 SP1 software on the system.
You need to manually install the Intel® Microsoft .NET Framework 3.5 SP1 software
on a Windows operating system.
To install the drivers:
1.
2.
Restart the computer, and then log on with Administrator privileges.
Insert the motherboard/system support DVD to the optical drive. The support
DVD automatically displays the Drivers menu if Autorun is enabled in your
computer.
If Autorun is NOT enabled in your computer, browse the contents of the support
DVD to locate the file ASSETUP.EXE from the BIN folder. Double-click the
ASSETUP.EXE to run the support DVD.
3.
6-24
Click the item Microsoft .NET Framework 3.5 SP1 software from the menu,
and then follow the onscreen instructions to complete the installation.
Chapter 6: Driver installation
6.7Intel® Rapid Storage Technology
enterprise 3.0 installation
This section provides the instructions on how to install the Intel® Rapid Storage
Technology enterprise 3.0 on the system.
You need to manually install the Intel® Rapid Storage Technology enterprise 3.0
utility on a Windows® operating system.
To install the Intel® Rapid Storage Technology enterprise 3.0 utility:
1.
2.
Restart the computer, and then log on with Administrator privileges.
Insert the motherboard/system support DVD to the optical drive. The support
DVD automatically displays the Drivers menu if Autorun is enabled in your
computer.
If Autorun is NOT enabled in your computer, browse the contents of the support
DVD to locate the file ASSETUP.EXE from the BIN folder. Double-click the
ASSETUP.EXE to run the support DVD.
3.
Click the Intel® Rapid Storage Technology enterprise 3.0 to begin
installation.
4.
When the Welcome to the Setup Program appears, click Next to start the
installation.
ASUS Z9PE-D16 Series
6-25
6-26
5.
Read the Warning message and click Next to continue.
6.
Read the License Agreement and click Yes to continue.
7.
Read the Readme File Information and click Next to continue.
Chapter 6: Driver installation
8.
After completing the installation, click Next to complete the setup process.
9.
Select Yes, I want to restart my computer now and click Finish to restart
your computer before using the program.
ASUS Z9PE-D16 Series
6-27
6.8Intel® I350 Gigabit Adapters Driver
installation
This section provides the instructions on how to install Intel® I350 Gigabit Adapters
Driver.
To install the Intel® I350 Gigabit Adapters Driver on a Windows® OS:
1.
2.
Restart the computer, and then log on with Administrator privileges.
Insert the motherboard/system support DVD to the optical drive. The DVD
automatically displays the Drivers menu if Autorun is enabled in your
computer.
If Autorun is NOT enabled in your computer, browse the contents of the support
DVD to locate the file AUTORUN.EXE and double-click the AUTORUN.EXE
and follow step 4 to run the installation.
3.
6-28
Click Intel® I350-AM4 Gigabit Adapters Driver.
Chapter 6: Driver installation
4.
When the Intel® PRO Network Connections – InstallShield Wizard window
appears, click Next to start the installation.
5.
Click I accept the terms in the license agreement and then click Next to
continue.
ASUS Z9PE-D16 Series
6-29
6-30
6.
Select the programs you want to install and click Next to continue.
7.
Click Install to start the installation.
Chapter 6: Driver installation
8.
The programs you select are being installed.
9.
Click Finish to finish the installation.
ASUS Z9PE-D16 Series
6-31
6.9Management applications and utilities
installation
The support DVD that came with the motherboard package contains the drivers,
management applications, and utilities that you can install to avail all motherboard
features.
The contents of the support DVD are subject to change at any time without
notice. Visit the ASUS website (www.asus.com) for updates.
6.9.1
Running the support DVD
Place the support DVD to the optical drive. The DVD automatically displays the
Drivers menu if Autorun is enabled in your computer.
If Autorun is NOT enabled in your computer, browse the contents of the support
DVD to locate the file ASSETUP.EXE from the BIN folder. Double-click the
ASSETUP.EXE to run the support DVD.
6.9.2
Drivers menu
The Drivers menu shows the available device drivers if the system detects installed
devices. Install the necessary drivers to activate the devices.
The screen display and driver options vary under different operating system
versions.
6-32
Chapter 6: Driver installation
6.9.3
Utilities menu
The Utilities menu displays the
software applications and utilities
that the motherboard supports.
Click an item to install.
6.9.4
Make disk menu
The Make disk menu contains
items to create the Intel RAID
driver disks.
6.9.5
Contact information
Click the Contact tab to display
the ASUS contact information.
You can also find this information
on the inside front cover of this
user guide.
ASUS Z9PE-D16 Series
6-33
6-34
Chapter 6: Driver installation
This appendix includes additional
information that you may refer to when
configuring the motherboard.
Appendix:
A
Reference information
Appendix summary
A.1
A.2
A
Z9PE-D16 block diagram..............................................................A-3
Z9PE-D16/2L block diagram.........................................................A-4
ASUS Z9PE-D16
A.1
Z9PE-D16 block diagram
ASUS Z9PE-D16
A-3
A.2
A-4
Z9PE-D16/2L block diagram
Appendix A: Reference information
ASUS contact information
ASUSTeK COMPUTER INC. (Taiwan)
Address
Telephone Fax E-mail
Web site
Technical Support
Telephone Online Support
15 Li-Te Road, Peitou, Taipei, Taiwan 11259
+886-2-2894-3447
+886-2-2890-7798
info@asus.com.tw
http://www.asus.com.tw
+886-2-2894-3447 (0800-093-456)
http://support.asus.com/techserv/techserv.aspx
ASUSTeK COMPUTER INC. (China)
Address
Telephone Fax Web site
Technical Support
Telephone Online Support
No.508, Chundong Road, Xinzhuang Industrial Zone,
Minhang District, Shanghai, China.
+86-21-5442-1616
+86-21-5442-0099
http://www.asus.com.cn
+86-21-3407-4610 (800-820-6655)
http://support.asus.com/techserv/techserv.aspx
ASUS COMPUTER INTERNATIONAL (America)
Address 800 Corporate Way, Fremont, CA 94539, USA
Fax +1-510-608-4555
Web site http://usa.asus.com
Technical Support
Support fax +1-812-284-0883
General support +1-812-282-2787
Online support http://support.asus.com/techserv/techserv.aspx
ASUS COMPUTER GmbH (Germany and Austria)
Address
Fax
Web site
Online contact
Harkort Str. 21-23, D-40880 Ratingen, Germany
+49-2102-959911
http://www.asus.de
http://www.asus.de/sales
Technical Support
Telephone +49-1805-010923*
Support Fax +49-2102-959911
Online support http://support.asus.com/techserv/techserv.aspx
* EUR 0.14/minute from a German fixed landline; EUR 0.42/minute from a mobile phone.
(510)739-3777/(510)608-4555
800 Corporate Way, Fremont, CA 94539.
Asus Computer International
Date :
Signature :
Representative Person’s Name :
Oct. 28, 2011
Steve Chang / President
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Supplementary Information:
FCC Part 15, Subpart E, Intentional Radiators
FCC Part 15, Subpart C, Intentional Radiators
FCC Part 15, Subpart B, Unintentional Radiators
Model Number : Z9PE-D16
Conforms to the following specifications:
Product Name : Mother board
hereby declares that the product
Phone/Fax No:
Address:
Responsible Party Name:
Per FCC Part 2 Section 2. 1077(a)
DECLARATION OF CONFORMITY
Ver. 110101
Manufacturer:
ASUS COMPUTER GmbH
HARKORT STR. 21-23, 40880 RATINGEN
GERMANY
Authorized representative in Europe:
Address, City:
Country:
Model name :
EN 60065:2002+A1:2006+A11:2008
EN 301 489-1 V1.8.1(2008-04)
EN 301 489-3 V1.4.1(2002-08)
EN 301 489-4 V1.3.1(2002-08)
EN 301 489-7 V1.3.1(2005-11)
EN 301 489-9 V1.4.1(2007-11)
EN 301 489-17 V2.1.1(2009-05)
EN 301 489-24 V1.4.1(2007-09)
EN 302 326-2 V1.2.2(2007-06)
EN 302 326-3 V1.3.1(2007-09)
EN 301 357-2 V1.3.1(2006-05)
EN 302 623 V1.1.1(2009-01)
EN 55024:1998+A1:2001+A2:2003
EN 61000-3-3:2008
EN 55020:2007
Signature : __________
Position : CEO
Name :
Jerry Shen
(EC conformity marking)
EN 62301:2005
Regulation (EC) No. 278/2009
Declaration Date: Oct. 28, 2011
Year to begin affixing CE marking:2011
CE marking
EN 62301:2005
Regulation (EC) No. 642/2009
EN 62301:2005
Regulation (EC) No. 1275/2008
2009/125/EC-ErP Directive
EN 60950-1:2006+A11:2009
EN 60950-1:2006
2006/95/EC-LVD Directive
EN 300 328 V1.7.1(2006-05)
EN 300 440-1 V1.4.1(2008-05)
EN 300 440-2 V1.2.1(2008-03)
EN 301 511 V9.0.2(2003-03)
EN 301 908-1 V3.2.1(2007-05)
EN 301 908-2 V3.2.1(2007-05)
EN 301 893 V1.4.1(2005-03)
EN 302 544-2 V1.1.1(2009-01)
EN 50360:2001
EN 50371:2002
EN 50385:2002
1999/5/EC-R &TTE Directive
EN 55022:2006+A1:2007
EN 61000-3-2:2006
EN 55013:2001+A1:2003+A2:2006
conform with the essential requirements of the following directives:
2004/108/EC-EMC Directive
Mother board
Z9PE-D16
Product name :
Ver. 110101
TAIWAN
Country:
declare the following apparatus:
No. 150, LI-TE RD., PEITOU, TAIPEI 112, TAIWAN R.O.C.
Address, City:
ASUSTek COMPUTER INC.
EC Declaration of Conformity
We, the undersigned,
(510)739-3777/(510)608-4555
800 Corporate Way, Fremont, CA 94539.
Asus Computer International
Date :
Signature :
Representative Person’s Name :
Mar. 08, 2012
Steve Chang / President
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Supplementary Information:
FCC Part 15, Subpart E, Intentional Radiators
FCC Part 15, Subpart C, Intentional Radiators
FCC Part 15, Subpart B, Unintentional Radiators
Model Number : Z9PE-D16/2L
Conforms to the following specifications:
Product Name : Mother board
hereby declares that the product
Phone/Fax No:
Address:
Responsible Party Name:
Per FCC Part 2 Section 2. 1077(a)
DECLARATION OF CONFORMITY
Ver. 110101
Manufacturer:
ASUS COMPUTER GmbH
HARKORT STR. 21-23, 40880 RATINGEN
GERMANY
Authorized representative in Europe:
Address, City:
Country:
Model name :
Declaration Date: Mar. 08, 2012
Year to begin affixing CE marking:2012
CE marking
EN 62301:2005
Regulation (EC) No. 642/2009
EN 62301:2005
Regulation (EC) No. 1275/2008
Signature : __________
Position : CEO
Name :
Jerry Shen
(EC conformity marking)
EN 62301:2005
Regulation (EC) No. 278/2009
EN 60065:2002 / A12:2011
2009/125/EC-ErP Directive
EN 60065:2002+A1:2006+A11:2008
EN 60950-1 / A12:2011
EN 301 489-1 V1.8.1(2008-04)
EN 301 489-3 V1.4.1(2002-08)
EN 301 489-4 V1.3.1(2002-08)
EN 301 489-7 V1.3.1(2005-11)
EN 301 489-9 V1.4.1(2007-11)
EN 301 489-17 V2.1.1(2009-05)
EN 301 489-24 V1.4.1(2007-09)
EN 302 326-2 V1.2.2(2007-06)
EN 302 326-3 V1.3.1(2007-09)
EN 301 357-2 V1.3.1(2006-05)
EN 302 623 V1.1.1(2009-01)
EN 55024:1998+A1:2001+A2:2003
EN 61000-3-3:2008
EN 55020:2007
EN 60950-1 / A11:2009
2006/95/EC-LVD Directive
EN 300 328 V1.7.1(2006-10)
EN 300 440-1 V1.4.1(2008-05)
EN 300 440-2 V1.2.1(2008-03)
EN 301 511 V9.0.2(2003-03)
EN 301 908-1 V3.2.1(2007-05)
EN 301 908-2 V3.2.1(2007-05)
EN 301 893 V1.4.1(2005-03)
EN 302 544-2 V1.1.1(2009-01)
EN 50360:2001
EN 50371:2002
EN 50385:2002
1999/5/EC-R &TTE Directive
EN 55022:2006+A1:2007
EN 61000-3-2:2006
EN 55013:2001+A1:2003+A2:2006
conform with the essential requirements of the following directives:
2004/108/EC-EMC Directive
Mother board
Z9PE-D16/2L
Product name :
Ver. 111121
TAIWAN
Country:
declare the following apparatus:
No. 150, LI-TE RD., PEITOU, TAIPEI 112, TAIWAN R.O.C.
Address, City:
ASUSTek COMPUTER INC.
EC Declaration of Conformity
We, the undersigned,
Download PDF

advertising