instaLL guiDe
FLC-IDS(RS)-BZ3-EN
Document numbeR
12390
Revision Date
20131002
FiRmwaRe
FLC-IDS(RS)-BZ3
haRDwaRe
FLRSBZ3
accessoRies
PROGRAMMING CABLE FLPROG (REQUIRED)
FLRF1/2 (OPTIONAL)
CARLINK ASCL2 (OPTIONAL)
notice
The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.
Automotive Data Solutions Inc. © 2013
beFoRe instaLLation
1- Connect module to computer
2- Login to Weblink account
3- Flash firmware to module (module is not preloaded with firmware)
4- Use accessories accordingly (accessories are sold separately) www.flashlogic.com
VEHICLE LIST - 1 OF 1
FEATURES
Page 2 oF 25
DOC.: #12390
• 20131002
NOTES
I This fi rmware covers Automatic Transmission
(AT) vehicles only.
II All the covered Push To Start (PTS) vehicles are equipped with a keyless authorization system called "Keyless Go".
C Class Sedan PTS AT
C Class Sedan STD key AT
C Class Coupe PTS AT
C Class Coupe STD key AT
CLS Class PTS AT
CLS Class STD key AT
E Class Sedan/Wagon PTS AT
E Class Sedan/Wagon STD key AT
E Class Sedan Diesel PTS AT
E Class Sedan Diesel STD key AT
E Class Coupe/Cabriolet PTS AT
E Class Coupe/Cabriolet STD key AT
GLK Class PTS AT
GLK Class PTS AT
GLK Class STD key AT
GLK Class STD key AT
GLK Class Diesel PTS AT
GLK Class Diesel PTS AT
GLK Class Diesel STD key AT
GLK Class Diesel STD key AT
SLK Class PTS AT
SLK Class STD key AT
* If equipped with a factory hood switch.
Automotive Data Solutions Inc. © 2013
08-13 2 • • • • • • • • •
08-13 1 • • • • • • • • •
12-13 2 • • • • • • • • •
12-13 1 • • • • • • • • •
12-13 4 • • • • • • • • •
12-13 3 • • • • • • • • •
10-13 4 • • • • • • • • •
10-13 3 • • • • • • • • •
10-13 4 • • • • • • • • •
10-13 3 • • • • • • • • •
10-13 2 • • • • • • • • •
10-13 1 • • • • • • • • •
08-12 2 • • • • • • • •
13 4 • • • • • • • •
08-12 1 • • • • • • • •
13 3 • • • • • • • •
08-12 2 • • • • • • • •
13 4 • • • • • • • •
08-12 1 • • • • • • • •
13 3 • • • • • • • •
12-13 2 • • • • • • • • •
12-13 1 • • • • • • • • •
• • • • • • •
• • • • • • •
• • • • • • •
• • • • • • •
• • • • • • •
• • • • • • •
• • • • • • •
• • •
• • •
• • •
• • •
• • •
• • •
• • •
• • • • • • • • • •
• • • • • • • • • • •
• • • • • • • • • • •
• • • • • • • • • •
• • • • • • •
• • • • • • • •
• • • • • • • •
• • • • • • • •
• • • • • • • •
•
•
•
•
•
•
•
•
•
• • •
• • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • • • • • • •
• • • • • • •
• • • • • • •
• • •
• • •
FLC-IDS(RS)-BZ3-EN www.flashlogic.com
BOX CONTENTS - 1 OF 1
BOX CONTENTS
MODULE
PROGRAMMING
BUTTON
A
B
C
D
LED 1
N
M
LED 2
H
G
J
I
L
K
EXPANSION PACK
E
F
XP LED 1 XP LED 2
O
Q
P
ACCESSORIES (SOLD SEPARATELY)
PROGRAMMING CABLE (REQUIRED)
T-HARNESS 1
2 PIN BLACK CONNECTOR
EXTRA CONNECTOR HOUSING
H-HARNESS 1
ADS-TOOLS-MB01 OR
MERCEDEZ BENZ P/N 639 589 01 07 00
10 PIN WHITE CONNECTOR
12 PIN BLACK CONNECTOR
AFTERMARKET HOOD SWITCH AND CABLE
Page 3 oF 25
DOC.: #12390
• 20131002
STICKER 1
STICKER 2
RF KIT (OPTIONAL)
COMPATIBLE MODELS ONLY
TELEMATICS DEVICE (OPTIONAL)
COMPATIBLE MODELS ONLY
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN www.flashlogic.com
imPoRtant technicaL note - 1 OF 1
instaLL viDeo gaLLeRY avaiLabLe onLine
Before installing this product, consult our Install Video Gallery and watch:
•
Vehicle Disassembly Procedure videos
•
Module Connection Procedures videos
•
Module Programming Procedures videos
Simply visit our forum and register at http://www.12voltdata.com/forum/viewtopic.php?f=340&t=9683&sid=a61772b486e4584ad6f058b171ffa425
Page 4 oF 25
DOC.: #12390
• 20131002
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN www.flashlogic.com
inteRioR view
COMPONENT LOCATOR - 1 OF 1
Page 5 oF 25
DOC.: #12390
• 20131002
DRiveR siDe view
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN
PassengeR siDe view
A
www.flashlogic.com
MODULE INSTALLATION PROCEDURE - 1 OF 1
01
02
OFF ACC
START the vehicle. Verify all vehicle functionalities. If the vehicle displays error messages or any malfunction: stop the installation and service the vehicle.
ENGINE
START
STOP
OFF ACC ON START
Turn OFF the vehicle.
03
04
05
06
START
STOP
F
Verify all keyfob functionalities (Door Lock,
Door Unlock, Trunk Release and RFID access if equipped).
07
08
OFF ACC START
WARNING: Any vehicle harness that is disconnected during installation, must be re-connected before performing any system tests. Failure to comply will result in vehicle displaying error messages. An OEM scantool will be required to clear the error messages.
START the vehicle. Verify all vehicle functionalities.
START
STOP
09
WARNING: If the vehicle displays error messages or any malfunction, stop the installation, verify every connection and if the problem persists, call technical support.
Insert the expansion pack in the module.
Connect the module to the computer with the programming cable (F port). Flash the module with the latest fi rmware then fl ash the expansion pack.
Connect and secure every connector to the vehicle, as shown in STEP 1 of the WIRING
DIAGRAM.
10
OFF ACC ON START
Turn OFF the vehicle.
ENGINE
STOP
11
Connect the C connector to the module, as shown in STEP 2 of the WIRING DIAGRAM.
C
12
Connect every other connector to the module, as shown in STEP 3 of the WIRING DIAGRAM.
13
14
15
16
17
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN
Page 6 oF 25
DOC.: #12390
• 20131002
F
I
RF
If required, connect a compatible RF Kit, as shown in STEP 4 of the WIRING DIAGRAM.
If required, connect a compatible Telematics
Device, as shown in STEP 4 of the WIRING
DIAGRAM.
If the vehicle is not equipped with a factory hood switch, install an aftermarket hood switch as shown in STEP 4 of the WIRING
DIAGRAM.
Put sticker 1 on a clean and visible surface in the engine bay and put sticker 2 under the dashboard near the OBDII connector.
Module installation procedure completed.
www.flashlogic.com
MODULE
N
M
C
D
O
A
B
P
J
I
L
K
H
G
Q
WARNING
1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4
2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1
E
F
STEP 2:
CONNECT THE FOLLOWING TO THE MODULE
C
RELAY
BLACK 20 PIN
D
STEP 3:
CONNECT THE FOLLOWING TO THE MODULE
BLUE 06 PIN
P
BLUE 10 PIN
BLACK 2 PIN (NC)
STEP 4
CONNECT IF REQUIRED
H
07 GRAY/WHITE - HOOD STATUS (-) INPUT
08 GRAY/BLACK (NC)
F
I
BLACK 4 PIN - RF CABLE
BLUE 4 PIN - TELEMATIC CABLE
Automotive Data Solutions Inc. © 2013
TYPE 1 - WIRING DIAGRAM - 1 OF 1
STEP 1:
CONNECT THE FOLLOWING TO THE VEHICLE
START THE VEHICLE WITH THE OEM KEYFOB
TO TEST THE CONNECTIONS
A1
A2
A1 CONNECTOR - WHITE
A2 HARNESS
Page 7 oF 25
DOC.: #12390
• 20131002
IGNITION SWITCH
IF NOT EQUIPPED
WITH AN OEM HOOD SWITCH,
INSTALL AN AFTERMARKET HOOD SWITCH
FLC-IDS(RS)-BZ3-EN
AFTERMARKET HOOD SWITCH (-)
RF KIT
TELEMATIC
www.flashlogic.com
TYPE 2 - WIRE CHART - 1 OF 1
C Class Sedan PTS AT
C Class Coupe PTS AT
E Class Coupe/Cabriolet PTS AT
GLK Class PTS AT
GLK Class Diesel PTS AT
SLK Class PTS AT
08-13
12-13
10-13
08-12
08-12
12-13
WIRE DESCRIPTION
CanH
CanL
CanH
CanL
CanH
CanL
CanH
CanL
CanH
CanL
CanH
CanL
~
~
~
~
~
~
~
~
~
~
~
~
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
WIRE COL
01 Brown/Red
02 Brown
01 Brown/Red
02 Brown
01 Brown/Red
02 Brown
01 Brown/Red
02 Brown
01 Brown/Red
02 Brown
01 Brown/Red
02 Brown
MODULE LOC
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
Page 8 oF 25
DOC.: #12390
• 20131002
A
A
A
A
A
A
A
A
A
A
A
A
COMPONENT LOC
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN www.flashlogic.com
TYPE 2 - WIRING DIAGRAM - 1 OF 2
STEP 1:
CONNECT THE FOLLOWING TO THE VEHICLE
START THE VEHICLE WITH THE OEM KEYFOB
TO TEST THE CONNECTIONS
A1
A2
A1 CONNECTOR - WHITE
A2 HARNESS
Page 9 oF 25
DOC.: #12390
• 20131002
IGNITION SWITCH MODULE
N
M
C
D
O
A
B
P
J
I
L
K
H
G
Q
WARNING
1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4
2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1
E
F
STEP 2:
CONNECT THE FOLLOWING TO THE MODULE
C
RELAY
BLACK 20 PIN
D
STEP 3:
CONNECT THE FOLLOWING TO THE MODULE
BLUE 06 PIN
P
BLUE 10 PIN
J1
H
07 GRAY/WHITE - HOOD STATUS (-) INPUT
08 GRAY/BLACK (NC)
F
I
BLACK 4 PIN - RF CABLE
BLUE 4 PIN - TELEMATIC CABLE
Automotive Data Solutions Inc. © 2013
STEP 4
CONNECT IF REQUIRED
01 PINK/RED - CANH
02 PINK/BLACK - CANL
IF NOT EQUIPPED
WITH AN OEM HOOD SWITCH,
INSTALL AN AFTERMARKET HOOD SWITCH
FLC-IDS(RS)-BZ3-EN
C1
CAN CONNECTORS
CAN JUNCTION CONNECTOR
REFER TO WIRE CHART
REFER TO COMPONENT LOCATOR
SEE MODULE PROGRAMMING PROCEDURE - PTS
TO IDENTIFY THE REQUIRED CAN CONNECTOR.
ONCE IDENTIFIED, DISCONNECT IT FROM THE CAN
JUNCTION CONNECTOR AND CONNECT IT TO C1.
01 CANH
02 CANL
IF THE REQUIRED CAN CONNECTOR DOES NOT FIT IN C1:
SEE NEXT PAGE FOR INSTRUCTIONS
AFTERMARKET HOOD SWITCH (-)
RF KIT
TELEMATIC
www.flashlogic.com
TYPE 2 - WIRING DIAGRAM - 2 OF 2
INSTRUCTIONS TO CHANGE THE HOUSING OF CAN WIRES
(ONLY IF THE CAN CONNECTOR DOES NOT FIT IN C1)
Page 10 oF 25
DOC.: #12390
• 20131002
1
RELEASE RETAINING CLIP OF CAN CONNECTOR.
2
RELEASE LOCKING MECHANISM.
REMOVE CAN WIRES FROM HOUSING.
3
INSERT EMPTY HOUSING IN CAN JUNCTION CONNECTOR
(TO AVOID LOSING IT).
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN
02 - CANL
01 - CANH
4
INSERT CAN WIRES IN PROVIDED HOUSING.
CONNECT IT WITH C1 HARNESS,
AS SHOWN IN WIRING DIAGRAM.
www.flashlogic.com
MODULE
N
M
C
D
O
A
B
P
J
I
L
K
H
G
Q
WARNING
1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4
2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1
E
F
STEP 2:
CONNECT THE FOLLOWING TO THE MODULE
C
RELAY
BLACK 20 PIN
D
STEP 3:
CONNECT THE FOLLOWING TO THE MODULE
BLUE 06 PIN
P
BLUE 10 PIN
BLACK 2 PIN (NC)
STEP 4
CONNECT IF REQUIRED
H
07 GRAY/WHITE - HOOD STATUS (-) INPUT
08 GRAY/BLACK (NC)
F
I
BLACK 4 PIN - RF CABLE
BLUE 4 PIN - TELEMATIC CABLE
Automotive Data Solutions Inc. © 2013
TYPE 3 - WIRING DIAGRAM - 1 OF 1
STEP 1:
CONNECT THE FOLLOWING TO THE VEHICLE
START THE VEHICLE WITH THE OEM KEYFOB
TO TEST THE CONNECTIONS
J1
B2
B2 HARNESS
B1
B1 CONNECTOR
A1
A1 CONNECTOR
A2
A2 HARNESS
Page 11 oF 25
DOC.: #12390
• 20131002
IGNITION SWITCH
IF NOT EQUIPPED
WITH AN OEM HOOD SWITCH,
INSTALL AN AFTERMARKET HOOD SWITCH
FLC-IDS(RS)-BZ3-EN
AFTERMARKET HOOD SWITCH (-)
RF KIT
TELEMATIC
www.flashlogic.com
TYPE 4 - WIRE CHART - 1 OF 1
CLS Class PTS AT
E Class Sedan/Wagon PTS AT
E Class Sedan Diesel PTS AT
GLK Class PTS AT
GLK Class Diesel PTS AT
12-13
10-13
10-13
13
13
WIRE DESCRIPTION
CanH
CanL
CanH
CanL
CanH
CanL
CanH
CanL
CanH
CanL
~
~
~
~
~
~
~
~
~
~
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
02 pin
WIRE COL
01 Brown/Red
02 Brown
01 Brown/Red
02 Brown
01 Brown/Red
02 Brown
01 Brown/Red
02 Brown
01 Brown/Red
02 Brown
MODULE LOC
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
(DATA) Front door jamb, passenger side
Page 12 oF 25
DOC.: #12390
• 20131002
A
A
A
A
A
A
A
A
A
A
COMPONENT LOC
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN www.flashlogic.com
MODULE
N
M
C
D
O
A
B
P
J
I
L
K
H
G
Q
WARNING
1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4
2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1
E
F
STEP 2:
CONNECT THE FOLLOWING TO THE MODULE
C
RELAY
BLACK 20 PIN
D
STEP 3:
CONNECT THE FOLLOWING TO THE MODULE
BLUE 06 PIN
P
BLUE 10 PIN
J2
H
07 GRAY/WHITE - HOOD STATUS (-) INPUT
08 GRAY/BLACK (NC)
F
I
BLACK 4 PIN - RF CABLE
BLUE 4 PIN - TELEMATIC CABLE
Automotive Data Solutions Inc. © 2013
STEP 4
CONNECT IF REQUIRED
TYPE 4 - WIRING DIAGRAM - 1 OF 2
STEP 1:
CONNECT THE FOLLOWING TO THE VEHICLE
START THE VEHICLE WITH THE OEM KEYFOB
TO TEST THE CONNECTIONS
J1
01 PINK/RED - CANH
02 PINK/BLACK - CANL
Page 13 oF 25
DOC.: #12390
• 20131002
C1
IGNITION SWITCH
B2
B2 HARNESS
B1
B1 CONNECTOR
A1
A1 CONNECTOR
A2
CAN CONNECTORS
A2 HARNESS
CAN JUNCTION CONNECTOR
REFER TO WIRE CHART
REFER TO COMPONENT LOCATOR
SEE MODULE PROGRAMMING PROCEDURE - PTS
TO IDENTIFY THE REQUIRED CAN CONNECTOR.
ONCE IDENTIFIED, DISCONNECT IT FROM THE CAN
JUNCTION CONNECTOR AND CONNECT IT TO C1.
01 CANH
02 CANL
IF THE REQUIRED CAN CONNECTOR DOES NOT FIT IN C1:
SEE NEXT PAGE FOR INSTRUCTIONS
IF NOT EQUIPPED
WITH AN OEM HOOD SWITCH,
INSTALL AN AFTERMARKET HOOD SWITCH
FLC-IDS(RS)-BZ3-EN
AFTERMARKET HOOD SWITCH (-)
RF KIT
TELEMATIC
www.flashlogic.com
TYPE 4 - WIRING DIAGRAM - 2 OF 2
INSTRUCTIONS TO CHANGE THE HOUSING OF CAN WIRES
(ONLY IF THE CAN CONNECTOR DOES NOT FIT IN C1)
Page 14 oF 25
DOC.: #12390
• 20131002
1
RELEASE RETAINING CLIP OF CAN CONNECTOR.
2
RELEASE LOCKING MECHANISM.
REMOVE CAN WIRES FROM HOUSING.
3
INSERT EMPTY HOUSING IN CAN JUNCTION CONNECTOR
(TO AVOID LOSING IT).
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN
02 - CANL
01 - CANH
4
INSERT CAN WIRES IN PROVIDED HOUSING.
CONNECT IT WITH C1 HARNESS,
AS SHOWN IN WIRING DIAGRAM.
www.flashlogic.com
01
OFF
ACC ON
START
LED 1 is solid RED. Insert key into ignition.
02
OFF
ACC ON
START
Turn key to ON position.
03
Wait, LED 1 will turn solid GREEN then will turn OFF.
MODULE PROGRAMMING PROCEDURE - STD KEY - 1 OF 1
06
OFF
ACC ON
START
Turn key to OFF position. Remove key from ignition.
07
Module Programming Procedure completed.
>>
WARNING: If LED 1 fl ashes RED/GREEN, turn ignition to OFF position. The vehicle is PTS.
Follow appropriate PTS sections.
04
OFF
ACC ON
START
START vehicle for 15 seconds. LED 1 will turn solid RED.
05
Wait, LED 1 will turn solid GREEN then will turn OFF.
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN
Page 15 oF 25
DOC.: #12390
• 20131002 www.flashlogic.com
MODULE PROGRAMMING PROCEDURE - PTS - 1 OF 1
>>
>>
One of the connectors of the CAN junction connector controls the keyless authorization system (Keyless Go). The following procedure will allow the module to identify the required
CAN connector.
Have the CAN junction connector accessible.
Identify every CAN connector whose CanH and CanL wires match the colors listed in the
WIRE CHART.
01
STOP ACC ON START
LED 1 is solid RED. Push start button to ON position.
ENGINE
START
STOP
02
Wait, LED 1 will fl ash RED/GREEN.
>>
04
If the parking lights do NOT fl ash, the required connector is NOT found. Reconnect it to the
CAN junction connector and repeat step 4 with another connector.
Wait, LED 1 will turn solid GREEN then will turn OFF.
05
STOP ACC ON START
START vehicle for 15 seconds. LED 1 will turn solid RED.
ENGINE
START
STOP
06
Wait, LED 1 will turn solid GREEN then will turn OFF.
03
>>
Disconnect the fi rst connector of the CAN junction connector whose CanH and CanL wires match the colors listed in the WIRE
CHART. Wait 5 seconds.
If the parking lights fl ash, the required connector is found. Connect it to the C1 connector as shown in the WIRING DIAGRAM and go to step 5.
Automotive Data Solutions Inc. © 2013
07
STOP ACC ON START
Push start button to OFF position.
ENGINE
START
STOP
08
Module Programming Procedure completed.
FLC-IDS(RS)-BZ3-EN
Page 16 oF 25
DOC.: #12390
• 20131002 www.flashlogic.com
11
12
10
13
14
15
16
17
18
08
09
07
01
02
03
04
05
06
instaLLation checKList - 1 OF 2
Page 17 oF 25
DOC.: #12390
• 20131002
checKList
WARNING: Vehicle engine will start many times. Test in a well ventillated area.
Open driver door window for easy vehicle access.
Enter vehicle. Start the vehicle and let it run for 15 seconds.
Stop the vehicle and exit vehicle.
Close all vehicle doors, hood and trunk.
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to step 7.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat step 6 and call technical support if the problem persists.
Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to step 8.
NO: Repeat step 7. If the problem persists, unlock the door using the OEM keyfob, enter vehicle and press brake pedal to shut down the vehicle and call technical support.
Unlock and open driver door.
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 3: Does the vehicle remote start?
YES: The module does NOT detect the door signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support.
NO: Go to step 10.
Open hood.
Question 4: Is the orange warning sticker "Sticker 1" placed under the hood?
YES: Leave hood open and go to step 11.
NO: Put the mandatory orange warning sticker "Sticker 1", leave hood open and go to step 11.
Close all doors.
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 5: Does the vehicle remote start?
YES: Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Go to question 6.
NO: Go to step 13.
Question 6: Is the vehicle equipped with a factory hood switch? (Inside hood latch)
YES: The module does NOT detect the hood signal from the vehicle communication network. Call technical support.
NO: Install the mandatory hood switch included in the kit. Repeat installation checklist.
Close hood.
Enter vehicle. Do NOT press brake pedal.
Close all doors.
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Wait for the vehicle to start.
Press brake pedal.
Question 7: Does the vehicle shut down?
YES: Go to step 19.
NO: The module does NOT detect the brake pedal signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support.
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN www.flashlogic.com
instaLLation checKList - 2 OF 2
25
24
26
27
23
19
20
21
22
checKList
Exit vehicle.
Close all doors.
Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Wait for the vehicle to start.
Question 8: Is the vehicle equipped with a keyless authorization system (Keyless Go) ?
YES: Touch the exterior driver door handle to unlock door using the keyless authorization system (Keyless Go). Within 45 seconds, go to step 23.
NO: Press UNLOCK button once [1x] on the OEM keyfob. Within 45 seconds, go to step 23.
Open driver door.
Question 9: Does the vehicle shut down?
YES: The module does NOT detect the unlock signal from the vehicle communication network. Call technical support.
NO: Go to step 24.
Enter vehicle.
Question 10: Is the vehicle equipped with a keyless authorization system (Keyless Go) ?
YES: Push vehicle start button once [1x]. Go to step 25.
NO: Insert key into ignition and turn key to ON position. Go to step 25.
Press and release brake pedal.
Question 11: Does the vehicle shut down?
YES: Repeat this procedure from step 3. If the problem persists, call technical support.
NO: Go to step 26.
Shut down the vehicle.
Installation checklist completed.
Page 18 oF 25
DOC.: #12390
• 20131002
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN www.flashlogic.com
>>
01
NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming.
>>
Time restriction. Complete next step within 7 seconds.
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1
To exit valet mode: repeat steps 1 to 4 then
START vehicle for 15 seconds.
02
OFF ACC
ENGINE
START
STOP
Cycle ignition ON fi ve times [5x OFF/ON] rapidly. Parking Light will fl ash once [1x].
03
Wait, Parking Light will fl ash once [1x] to indicate that the valet mode is ON or twice [2x] to indicate that the valet mode is OFF.
04
OFF ACC ON START
Turn ignition to OFF position.
START
STOP
05
Valet Mode Programming Procedure completed.
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN
Page 19 oF 25
DOC.: #12390
• 20131002 www.flashlogic.com
aFteRmaRKet Remote PRogRamming: notes
I All aftermarket remotes must be programmed to the
RF-Kit.
Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.
aFteRmaRKet Remote PRogRamming - 1 OF 1
Page 20 oF 25
DOC.: #12390
• 20131002
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN www.flashlogic.com
>>
>>
>>
It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the
Module Navigation will drain vehicle battery.
To exit the Module Navigation at any time:
Follow STEP 13.
Module must be programmed to the vehicle.
04
05
Use the Module Navigation Chart on the next page.
06
01
OFF ACC ON START
Set ignition to OFF position.
ENGINE
STOP
02
TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid
GREEN.
07
08
03
[X]
IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will fl ash GREEN an equal amount of times continuously.
Automotive Data Solutions Inc. © 2013
09
MODULE NAVIGATION PROCEDURE - 1 OF 1
TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid
RED.
10
[Y]
IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will fl ash RED an equal amount of times continuously.
TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid
GREEN.
11
12
[Z]
LED 1 will flash GREEN as many times as the current (or default) setting number, continuously.
13
[Z]
IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will fl ash GREEN an equal amount of times continuously.
To return to the MENUS: exit the Module
Navigation and redo the Module Navigation
Procedure.
14
>>
FLC-IDS(RS)-BZ3-EN
Page 21 oF 25
DOC.: #12390
• 20131002
To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED.
[Y]
LED 1 will fl ash RED as many times as the current option number continuously.
Configure every other setting and proceed to step 13.
MANDATORY: EXIT MODULE NAVIGATION.
Press and hold programming button for 7 seconds. LED 1 will fl ash RED rapidly. Release programming button. LED 1 will turn OFF.
Module navigation completed.
Failure to exit the Module Navigation will drain vehicle battery.
www.flashlogic.com
moDuLe navigation chaRt - 1 OF 1
Page 22 oF 25
DOC.: #12390
• 20131002
moDuLe navigation chaRt: notes
I Default settings are listed in bold.
II Make sure the option is covered on the vehicle before attempting to change the setting.
*Vehicle will shutdown when a door is opened.
Automotive Data Solutions Inc. © 2013
01 CONFIGURATION
02-07 Technical Support only
FLC-IDS(RS)-BZ3-EN
01
02
03
04
05
06
07
08
09
DISARM/UNLOCK BEFORE START
RELOCK AFTER START
RELOCK AFTER SHUTDOWN
FORCE UNLOCK ALL ON FIRST PRESS
TAKEOVER
SECURE TAKEOVER DELAY
FACTORY KEYLESS RS SEQUENCE
MODULE RUN TIME
WAIT TO START DELAY
10-15 N/A
01 N/A
01
02
03
04
01
02
03
04
02
01
02
03
04
01
02
01
02
01
02
01
02
01
05
06
07
08
01
02
03
04
05
06
07
08
01
01
25 MIN
30 MIN
35 MIN
15 min
02 sec
05 SEC
08 SEC
10 SEC
15 SEC
20 SEC
25 SEC
30 SEC
N/A
N/A
oFF
ON
oFF
ON
oFF
ON
oFF
ON
enabLe
DISABLE*
45 sec
90 SEC
03 MIN
04 MIN
DISABLE
N/A
LOCK + UNLOCK + LOCK
LocK + LocK + LocK
03 MIN
05 MIN
10 MIN
15 MIN www.flashlogic.com
Remote staRteR eRRoR coDes - 1 OF 1
Remote staRteR eRRoR coDes: notes
I WARNING: The following applies only when the parking lights are connected and supported by the system.
II After a remote starter failure, the parking lights will fl ash
[X] number times to indicate an error code. See table.
09
10
11
12
13
14
15
16
03
04
05
06
07
08
[X] numbeR oF PaRKing Light FLashes
Foot brake is ON.
Hood is open.
Engine tach signal is lost.
System is in Valet Mode.
Vehicle is moving (VSS).
Glow plug timeout error.
RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.
N/A
N/A
N/A
N/A
N/A
N/A
CAN communication failure during RS sequence.
Page 23 oF 25
DOC.: #12390
• 20131002
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN www.flashlogic.com
moDuLe Diagnostics - 1 OF 1 test moDuLe
I DURING PROGRAMMING
II DURING REMOTE START
III WITH IGNITION OFF
Flashing RED
Solid RED
Flashing GREEN
Solid GREEN then OFF
OFF
Flashing RED
Solid RED
Flashing GREEN
Solid GREEN then OFF
OFF
Flashing RED
Solid RED
Flashing GREEN
Solid GREEN then OFF
OFF
Missing/wrong information from fi rmware or vehicle.
Module waiting for more vehicle information.
Additional steps required to complete module programming.
Module correctly programmed.
No activity or module already programmed.
Module incorrectly programmed.
Module incorrectly programmed.
Module correctly programmed and operational.
Reset in progress.
Invalid ground when running status from remote starter.
Module incorrectly programmed or connected.
Module not programmed. Waiting for more vehicle information.
False ground when running status from remote starter.
Reset in progress.
Module at rest and ready for a remote start sequence.
Page 24 oF 25
DOC.: #12390
• 20131002
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN www.flashlogic.com
01
02
03
04
Disconnect all connectors from module except the BLACK 20-PIN connector.
07
MODULE RESET PROCEDURE - 1 OF 1
Reconnect all connectors.
Disconnect the BLACK 20-PIN connector.
08
Repeat programming procedure.
PRESS AND HOLD programming button while connecting the BLACK 20-PIN connector.
Wait, LED 1 will flash RED. RELEASE programming button.
LED 1 will turn RED for 2 seconds.
>>
Failure to follow procedure may result with a
DTC or a CHECK ENGINE error message.
05
06
Module RESET completed.
Automotive Data Solutions Inc. © 2013 FLC-IDS(RS)-BZ3-EN
Page 25 oF 25
DOC.: #12390
• 20131002 www.flashlogic.com
![Idatastart BZ3 AKX-IDS(RS)-BZ3-[ADS-BZ3] Install Guide](http://s1.manualzz.com/store/data/006726659_1-2c2a4d0d1982ac0b51a6575d461be7c8-150x150.png)