Dacor REMP3 Specifications

Dacor REMP3 Specifications
Installation Instructions
Downdraft Raised Vent
Models: ERV36-ER, ERV48-ER
These downdraft vents are designed for use with Dacor ® ER36D and ER48D
series ranges.
Part No. 103106 Rev. C
Tested in accordance with the latest edition of ANSI Z 21.1 standard for household gas
cooking appliances, ANSI/UL 858 household electrical ranges, CAN/CSA-C22.2 NO. 64 Standard for Household
Electric Cooking and Liquid Heating Appliances, and UL 507 electric fans .
All specifications subject to change without notice. Dacor assumes no liability for changes to specifications.
© 2007 Dacor, all rights reserved.
Table of Contents
Before You Begin............................................................... 1
Important Safety Instructions........................................... 1
Important Information About Safety Instructions............... 1
Safety Symbols and Labels.............................................. 1
General Safety Precautions.............................................. 2
Customer Service Information.......................................... 3
If You Need Help............................................................... 3
Appliance Data Plate........................................................ 3
Product Specifications...................................................... 3
Product Dimensions.......................................................... 3
Installation Specifications................................................. 4
Electrical Specifications.................................................... 4
Planning the Installation.................................................... 4
Planning the Duct Work.................................................... 6
Installation Instructions..................................................... 8
Installation Preparation..................................................... 8
Installation......................................................................... 8
Verifying Proper Operation.............................................. 12
Installation Checklist....................................................... 12
Before You Begin...
Important:
•
Installer: In the interest of safety and to minimize problems, read these installation instructions completely and carefully before you begin the installation process. Leave these installation instructions with the customer.
•
Customer: Keep these installation instructions for future reference and the local electrical inspector’s use.
Important Safety Instructions
Safety Symbols and Labels
Important Information About
Safety Instructions
•
•
DANGER
The Important Safety Instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or operating this or any other appliance.
Immediate hazards that WILL result in severe personal
injury or death.
Always contact the Dacor Customer Service Team
about problems and conditions that you don’t understand. See Customer Service Information.
Hazards or unsafe practices that COULD result in severe
personal injury or death.
warning
caution
Hazards or unsafe practices that COULD result in minor
personal injury or property damage.
DANGER
IMPORTANT: Do not store or use combustible,
flammable or explosive vapors and liquids (such as
gasoline) inside or in the vicinity of this or any other
appliance. Also keep items that could explode, such
as aerosol cans, away from the range. Do not store
flammable or explosive materials in adjacent cabinets or
areas.
READ AND SAVE THESE INSTRUCTIONS
1
Important Safety Instructions
General Safety Precautions
To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following:
Warning
1.
2.
3.
Do not install or operate this unit if it has been
damaged, dropped, has damaged electrical wiring
or is not working properly. If the product is damaged
when received, immediately contact the dealer or
builder.
Use this raised vent only for its intended purpose
as outlined in the use and care manual. Do not use
this unit to vent hazardous or explosive materials
or vapors. This appliance is not intended for
commercial use.
The customer should not install, repair or
replace any part of this unit unless specifically
recommended in the literature accompanying it. A
qualified service technician should perform all other
service. Contact the Dacor Customer Service Team
for examination, repair or adjustment.
warning
11. To reduce the risk of electric shock or fire connect
remote blowers with a total combined current draw
of eight (8) amps or less.
12. The installer must show the customer the location
of the electrical outlet so that the customer knows
where and how to disconnect power.
13. Read the use and care manual completely before
using this raised vent.
14. Do not tamper with the controls.
15. Never allow the filters or vent openings to become
blocked or clogged. Do not allow foreign objects,
such as cigarettes or napkins, to be sucked into the
vent holes.
4.
Keep all packaging materials away from children.
Plastic bags can cause suffocation.
16. Clean the filters and all grease-laden surfaces often
to prevent grease fires and maintain performance.
Clean this appliance only as specified in the use
and care manual.
5.
This raised vent must be installed and grounded by
a qualified installer according to these installation
instructions. All installation work and electrical
wiring must be performed in accordance with all
applicable codes and standards, including fire-rated
construction.
17. Do not leave children or pets alone or unattended in
the area around the range when it is in use. Never
allow children to sit or stand on an appliance. Do
not let children play with a range or the raised vent.
Do not store items of interest to children above or
around the range.
6.
Install or locate this appliance only in accordance
with these installation instructions and the Dacor
range installation instructions. Improper installation,
adjustment, alteration, service or maintenance can
cause serious personal injury or property damage.
18. Install this raised vent only with Dacor ER36D and
ER48D series ranges.
7.
Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE) and the local code
authorities.
8.
When cutting or drilling into the wall or ceiling,
do not damage electrical wiring and other hidden
utilities.
9.
Always vent ducted fans to the outdoors. Do not
vent exhaust air into spaces within walls or ceilings
or into attics, crawl spaces or garages.
10. Before installing or servicing the raised vent,
disconnect the power plug from the electrical outlet.
2
19. This appliance is equipped with a three-prong
grounding plug for your protection against possible
electric shock hazards. It must be plugged into
a dedicated, grounded electrical outlet. Where a
standard two-prong wall receptacle is encountered,
it is the personal responsibility and obligation of
the customer to have it replaced with a dedicated,
properly grounded three-prong wall receptacle. Do
not under any circumstances:
•
Cut or remove the
third (ground) prong
from the power cord.
•
Use an adapter plug.
•
Use an extension
cord.
•
Use a power cord that
is frayed or damaged.
•
Use of a ground fault
interrupter (GFI) is not
recommended.
Customer Service Information
If You Need Help...
Appliance Data Plate
If you have questions or problems with installation, contact
your Dacor dealer or the Dacor Customer Service Team.
When you call, have the model and serial number of the
appliance ready. The model and serial number are printed
on the appliance data label on the front of the unit.
The appliance data label also specifies the power supply
requirements.
Dacor Customer Service Team
Phone: Web site:
Monday - Friday 6:00 a.m. to 5:00 p.m. Pacific Time
Model Identification:
ERV36-ER = 36-Inch Raised Vent
ERV48-ER = 48-Inch Raised Vent
(800) 793-0093
www.Dacor.com
Product Specifications
Product Dimensions
Stiffener
across back
Model
Number
2 1/4"
(57 mm)
Top Cap
Width (A)
Chassis
Width (B)
ERV36-ER
36” (914 mm)
33 3/8” (848 mm)
ERV48-ER
48” (1219 mm)
43 3/8” (1102 mm)
Tolerances: +1/16”, -0, (1.6 mm,0) unless otherwise stated
1 15/16"
(49 mm)
2 13/16"
(71 mm)
“A”
Vent shown
in raised
10"
position (254 mm)
“B”
18 13/16”
(478 mm)
3 3/4"
(95 mm)
30 ¼"
30 ¼" (768 mm)
(768 mm)
to
37 ¼"
(946 mm)
Appliance
data label
6"
(152 mm)
Motor
Cover
13/16"
(21 mm)
28" 3 prong
grounded
power cord
Adjustable
Anchor Legs
3
Installation Specifications
warning
•
•
Observe all governing codes and ordinances during
planning and installation. Contact your local building
department for further information.
Planning the Installation
System Layout
•
The electric outlet for the raised vent should be
installed only by a licensed electrician.
Electrical Specifications
The raised vent is supplied with a 28” (711 mm) power
cord terminated by a three-prong plug. Plug it directly into a
dedicated, grounded, three prong, electrical outlet. Do not
use an extension cord.
The correct voltage, frequency and amperage must be supplied to the electrical outlet from a grounded, single phase
circuit that is protected by a properly sized circuit breaker
or time-delay fuse.
Electrical Supply Requirements
•
A 3 prong electrical outlet connected to a 120 Vac, 60
Hz, 15 Amp. grounded, dedicated circuit is required.
•
The customer must supply conduit with minimum
current carrying capacity of 8 Amps to supply power
to the remote blower from the raised vent. See
Planning the Duct Work for further details.
•
The above specifications are for reference only. If the
power supply requirements shown above do not agree
with those listed on the appliance data label, use the
required voltage, frequency and amperage ratings on
the appliance data label.
•
It is the owner’s responsibility to ensure that electrical
outlet is installed by a licensed electrician. The electrical installation must comply with the latest revision of
the National Electric Code ANSI/NFPA 70 (latest revision) and local codes and ordinances.
•
If the electrical service provided does not meet the
product specification, or does not conform to the NEC
or local standards, do not proceed with the installation.
Call a licensed electrician to correct the electrical service before proceeding.
•
Locate the electrical outlet in an accessible location,
so that the power plug can be disconnected for service
without removing the raised vent or the range from the
cabinet.
The vent system consists of the raised vent itself and a
remote blower. You must install a Dacor model REMP3
or REMP16 remote blower for the raised vent to operate properly. For directions on installing the remote
blower, see the REMP3/16 installation instructions.
warning
•
Failure to install a remote blower or proper duct
work may result in a back draft and/or the insufficient
venting of smoke and fumes.
•
To reduce the risk of personal injury caused by
reaching over a hot appliance, cabinet storage
space located directly above the range should be
avoided.
•
Do not store combustible materials or items adversely affected by heat in cabinet areas above the appliance.
•
Follow the instructions and diagrams for minimum
safe clearances and installation location. Failure to
do so may result in a fire or safety hazard.
•
Wire the remote blower to turn on when the raised vent
is turned on by running a piece of conduit parallel to
the duct work and connecting it to the raised vent on
one end and the remote blower on the other. There are
7/8” access holes in the bottom and side of the raised
vent for connecting the conduit.
Vent shown in
down position
Side
Bottom
Conduit Access Hole Locations
•
4
The raised vent exhaust may be configured to vent
through the back, the bottom or through one of the
sides. The maximum allowable duct run must be taken
into consideration when determining the layout. See
Planning the Duct Work for further details.
Installation Specifications
•
•
•
•
Install the raised vent and range so that they can be
removed if service is required.
Countertop Height:
The raised vent is equipped with adjustable anchor legs
to accommodate various cabinet heights. See Product
Dimensions.
Max: 37 ¼” (946 mm)
Plan the installation so that all minimum dimensions
are met or exceeded. All contact surfaces between the
raised vent and any cabinets or walls must be solid and
at right angles. Refer to the range installation instructions for the minimum dimensions specific to the particular range being installed.
Backsplash
Min: 30 ¼” (768 mm)
1/4" (6 mm)
Min. flat ledge
Vertical
non-combustible
surface rear wall
C
Allow room for the exhaust duct coming out of the unit.
See Planning the Duct Work for further details.
Model Number
ERV Cutout
Width (C)
Range Cutout
Width (D) Min.
ERV36-ER
33 1/2” (848 mm)
36 1/16” (916 mm)
ERV48-ER
43 1/2” (1102 mm) 48 1/16” (1221 mm)
2 13/16"
(71 mm)
10" (254 mm) Min.
*
* Depth dimensions are at the discretion of the customer.
For reference, depth of the ER36D/ER48D range is 28 ¼”
(718 mm) from the front panel, excluding trim and knobs.
to combustible side
walls above the range
(both sides)
D
Cabinet Cutout - Top View
REMP Series
Remote Blower
All tolerances: +1/16”, -0, (1.6 mm,0) unless otherwise stated
Outside Wall
Wall Board
Duct work between
ERV and remote
blower
REMP Series
Remote Blower
Backsplash
Cabinet Back
ERV
Wall Board
ERV
ER36D or
ER48D Range
ERV configured
for rear exhaust
ER36D or
ER48D Range
ERV configured for
bottom exhaust
Floor
Floor
Power conduit from ERV
to remote blower
Example of Layout with Rear Exhaust
(Side View)
Duct work between ERV
and remote blower
Example of Layout with Bottom Exhaust
(Side View)
5
Installation Specifications
Planning the Duct Work
warning
•
To reduce the risk of fire and to properly exhaust air,
be sure to duct air outside the house or building. Do
not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages.
•
Tape all duct joints securely to prevent combustion by-products, smoke or odors from entering the
home. Doing so will also improve system efficiency.
•
Do not exhaust more than one vent into a single
duct run.
•
For proper operation this unit must be installed with
a remote blower. Use only Dacor models REMP3 or
REMP16.
•
Use only duct work constructed of materials deemed
acceptable by state, municipal and local codes
•
DO NOT install an additional in-line or external blower to increase the length of the duct run. Even small
differences between blower air flow rates can greatly
reduce the air draw by the hood.
6 1/2"
(165 mm)
Side
Side
Exhaust Duct Exhaust Duct
Side Exhaust
Duct
3 1/4" x 10"
Rear Exhaust
Duct
Bottom
Exhaust Duct
3 1/4" x 10" Motor
Rear Exhaust Cover
Duct
Bottom
Exhaust Duct
•
When connecting the duct work to the back of the unit,
the customer must supply a 3 ¼” X 10” rectangular
transition to make the connection.
•
For side and bottom exhaust connections, use the supplied ATD2 transition to connect the duct work to the
unit. It transitions between the narrow exhaust outlet on
the unit and a 3 ¼” X 10” rectangular duct connection.
On bottom exhaust installations cut a hole in the floor
to allow the transition and/or duct work to pass through
the floor.
6
•
On side exhaust installations, allow five inches of space
on the side for the ADT2 exhaust transition plus additional space for the duct attached to it (X).
X
5”
ATD2
The ERV raised vent can be configured to exhaust
through the back, the bottom or either side.
25 15/16" (659 mm)
•
ADT2 Transition
•
All duct work materials (including screws and duct tape)
must be purchased separately by the customer.
•
When planning new duct work, always look for the
shortest, most direct route to the outside.
•
You can increase the duct size over the duct run if
desired. To prevent a back draft, never decrease the
duct size over the run.
•
Do not rely on duct tape alone to seal duct joints.
Fasten all connections with sheet metal screws and
tape all joints with certified silver tape or duct tape.
•
Use sheet metal screws as require to support the duct
weight.
•
To prevent back-drafts, a damper at the duct outlet may
also be required.
•
Make sure duct work does not interfere with floor joists
or wall studs.
•
With concrete slab construction, “box-in” the duct work
to prevent it from collapsing when the wet concrete is
poured. Also allow room for electrical conduit from the
remote blower.
•
Cross-drafts or air currents caused by adjacent open
windows or doors, heating/air conditioning outlets, ceiling fans and recessed ceiling lights reduce vent efficiency.
Installation Specifications
Duct Work Design Tips
•
Wherever possible, reduce the number of transitions
and turns to as few sharp angles as possible. Two
staggered 45° angles are better than one 90°. Keep
turns as far away from the hood exhaust as possible,
with as much space between each bend as possible.
•
For best performance, use round duct instead of rectangular, especially when elbows are required.
•
If multiple elbows are used, try to keep a minimum of
24” of straight duct between them. Avoid “S” or “back to
back” configurations of adjacent elbows.
•
In regions where the weather gets extremely cold,
thermal breaks, such as a short section of non-metallic
duct, should be used to avoid indoor heat loss. The
break should be located as close to the pass through
point to the outside as possible.
•
Do not use flexible metal duct.
Calculating the Maximum Duct Run Length
•
Do not use duct work that is smaller in cross-sectional
area than the required duct sizes in the table to the
right.
•
For best performance, keep the duct run as short
as possible and never exceed the maximums stated
below.
•
The maximum straight duct length for the raised vent
system depends on the model of remote blower used
with vent system and the number of elbows and transitions used. The equivalent number of feet for each
elbow and transition must be subtracted from the maximum straight length to compensate for wind resistance
To determine the maximum allowable length of the duct
work, subtract all of the equivalent lengths of the elbows
and transitions listed below from appropriate Maximum
Equivalent Straight Lengths.
For example, for a raised vent system using 10 inch
duct, a REMP3 remote blower and three (3) 90° elbows:
•
From the Maximum Equivalent Straight Lengths table,
the maximum length without transitions and elbows is
40 feet.
•
The total equivalent length of the three (3) 90° 10 inch
elbows is
3 X 5 feet = 15 feet.
•
The maximum amount of straight duct that can be used
with a REMP3 and the elbows is: 40 feet - 6 feet = 34
feet.
Duct Size
Used
Maximum Equivalent Straight Lengths of
Duct Work
Using Model
REMP3 Remote
Blower
Using Model
REMP16 Remote
Blower
8 Inch
50 feet (15.2 meters)
60 feet (18.3 meters)
10 Inch
40 feet (12.2 meters)
70 feet (21.3 meters)
3 ¼” X 10” 40 feet (12.2 meters)
60 feet (18.3 meters)
3 1/4" x 10"
90° Elbow
3 1/4" x 10"
45° Elbow
Transistion
3 1/4" to 8” Round
Transistion
3 1/4" to 10" Round
15 Feet
7 Feet
4 Feet
4 Feet
3 1/4" x 10"
90° Flat Elbow
45° Elbow
Round Duct
90° Elbow
Round Duct
90° Transistion
3 1/4" x 10" to
8" Round
20 Feet
8" Diameter - 3 Feet
10" Diameter - 2 Feet
8" Diameter - 7 Feet
10" Diameter - 5 Feet
25 Feet
Equivalent Lengths - Duct Elbows and Transitions
7
Installation Instructions
Installation Preparation
2. Cut and remove the foil material inside the knock-out
hole. If you fail to remove the foil, the vent will not work.
Verify Package Contents
3. If the unit will vent through the bottom or side:
•
•
Use and care manual
•
Anchoring legs
•
4 wood screws for anchor legs
•
3 wire nuts
•
ADT2 duct transition
•
2 sheet metal screws for ADT2 mounting
•
2 nuts and washers to secure anchor legs
•
Insulation foam
For side installations, attach the supplied ATD2
transition to the side of the unit that will exhaust the
air. Install an elbow to the transition with the output
pointing down.
ADT2 side
installation
Verify that the raised vent and blower being installed are a
matched pair before beginning the installation.
Installation
warning
•
If the electrical service (electrical outlet) does not
meet the Electrical Specifications on page 4, do
not proceed with the installation. Call a licensed
electrician and have an electrical outlet installed that
meets the specifications.
Install the vent only in a vertical orientation. Do not mount
the vent on a slant or angle.
ADT2 bottom
installation
Installing the Raised Vent
1. Remove the appropriate side, back or bottom exhaust
knockout, depending on the duct configuration, from
the raised vent assembly by cutting the metal cross
overs and removing the insert.
ADT2 Transition Installation
•
For bottom installations, attach the supplied ATD2
transition to the bottom of the unit. Cut a hole in the
cabinet floor to allow the exhaust transition and/or
the duct to pass through the floor.
Back of Unit
Side
Knock-out
Side
Knock-out
Top of vent resting
on countertop
Cut hole in floor to allow
duct to pass through on
bottom venting installations
Rear knock-out with
metal cross overs
shown
Bottom
Knock-out
Vent Knock-out Locations
8
Floor
Installation Instructions
4. If the unit will exhaust air from the back, attach a
3 1/4” X 10 duct to the vent hole created by removing
the knock-out on the back of the unit.
5. Loosely attach the anchoring legs to the studs on the
left and right sides of the raised vent using the provided
hex nuts and washers.
Installing the Remote Blower and Ducts
1. Install the remote blower according the remote blower
installation instructions.
2. Install the duct work between the remote blower inlet
and the exhaust of the raised vent according to the
Installation Specifications. Use sheet metal screws
and duct tape to connect all of the pieces. Support the
duct weight as necessary to ensure sealed joints.
Front of
Raised Vent
REMP Series
Remote Blower
Anchor Leg
Put nuts/
washers on
studs
Wall Board
6. Place the vent into the rear of the countertop cutout
with the electrical access panel toward the front.
Backsplash
Top of vent resting
on countertop
Anchor Leg
Electrical Access
Panel
ERV
ER36D or
ER48D Range
Duct work between
ERV and remote
blower
ERV configured
for rear exhaust
Floor
Floor
7. Adjust the anchoring leg height so that the end caps
are gently resting on the counter, then tighten the hex
nuts.
8. Secure the anchoring legs to the cabinet floor with the
screws provided.
Conduit that supplies power
from ERV to remote blower (see
Electrical Installation, page 10)
Example of Installation with Rear Exhaust
(Side View)
9
Installation Instructions
Electrical Installation
warning
ELECTRIC SHOCK HAZARD - Do not connect power to
the unit until installation is complete.
1. Run the conduit line used to supply power from the
raised vent to the remote blower parallel to the duct
work.
2. Make sure the raised vent power plug is disconnected
from the electrical outlet.
3. Remove the cover from the raised vent electrical
access panel.
4. Connect the conduit to the remote blower as shown in
the wiring diagrams on this page and the facing page.
5. Replace the electrical access panel.
Match wire colors to
terminals as shown
Wires to power plug
Pre-wired at factory
Do not modify
BLACK
Power
Input
Ground
Electrical Access
Panel
Blower
Output
WHITE
GREEN
ERV Raised Vent
Front View
Attach ground wire
as shown
To power conduit
Connect other end of
wires to remote blower
terminal block
ERV Electrical
Access Panel
10
Installation Instructions
Wires from power conduit.
Connect other end of wires to
“Blower Output” inside ERV
electrical access panel
Match wire colors to
terminals as shown
N1
L1
BLACK
WHITE
GREEN
Gnd
ERV
Outside Wall
Gnd
N1
L1
Remote Blower
Terminal Block
Remote Blower
Wiring
REMP Series
Remote Blower
ER36D or
ER48D Range
See ERV electrical
access panel on
facing page
Floor
Power conduit from ERV
to remote blower
Example of Installation with Bottom Exhaust
(Side View)
Range Installation
Install the range according to the range installation instructions.
Once the range is installed, make sure that the top cap on the raised vent intake does not
catch on the back edge of the range when the intake is lowered.
If interference does occur, adjust the position of the range by moving it against the front
edge of the countertop cutout.
Make sure the vent anchoring legs are properly secured to the cabinet base with the supplied wood screws. Failure to eliminate any interference may result in permanent damage
to the vent.
11
Installation Instructions
Verifying Proper Operation
warning
•
Read the raised vent use and care manual completely before operation.
•
Install all of the front filters prior to operating the
raised vent. Refer to the use and care manual for
filter installation instructions.
caution
To prevent damage to the raised vent power cord, route it
away from the surfaces of the range before connecting it.
1. Make sure the power switch on the top of the raised
vent is in the up position.
2. Plug the raised vent power plug into the electrical outlet.
3. Press the power switch once to raise the vent to its
operating position.
4. Once in the up position, turn the variable speed control switch in both directions to verify that the blower
is operating correctly. Turn the variable speed control
switch counter-clockwise to hi-speed and clockwise to
low speed.
5. Press the top cap up/down switch once to lower the
vent.
Installation Checklist
□□ Are the anchor legs extended down to make contact
with the floor and tightened into place? Are the anchor
legs fastened to the floor? Is the unit level?
□□ Is the duct work completely installed? Are all joints
attached with sheet metal screws and wrapped with
duct tape?
□□ Is the power input for the remote blower connected to
the raised vent electrical access panel?
□□ Are the vent filters installed according to these instructions?
□□ Is the power cord routed away from the hot surfaces of
the range.
□□ Is the unit connected to an electrical outlet that meets
the electrical specifications in these instructions?
□□ Has proper operation been verified?
□□ Have any problems been noted on the warranty card
or during the on-line activation? Has the warranty been
activated on-line or the warranty card been filled out
completely and mailed?
12
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement