Technical Data Sheet – 8094R Permasolid® Air Dry Clear Coat 8094 GENERAL DESCRIPTION A VOC compliant, energy efficient, productive, air dry clear coat designed for single or multi panel repairs in air dry or force dry environments. This versatile clear delivers very good gloss and appearance over solvent borne and waterborne basecoats. 8094 uses the current Permasolid® Low VOC Hardener and reducer set, enabling customers to employ a common hardener and reducer set for mixing all of their Spies Hecker ® low VOC 2K urethane undercoats and clear coats. The products referenced herein may not be available for sale in your market. Please consult your distributor for product availability. MIXING COMPONENTS Permasolid® Air Dry Clear Coat 8094 PERMASOLID LOW VOC HARDENERS Permasolid® Low VOC Hardener 3192 Fast (18 - 24°C / 64 - 75 °F), Permasolid® Low VOC Hardener 3194 Medium (23 - 29°C / 73 - 84 °F), or Permasolid® Low VOC Hardener 3196 Slow (28 - 35°C / 82 - 95 °F) For optimum hardener selection, refer to TDS # 062. REDUCERS Permasolid® Low VOC Reducer 3394 Medium or Permasolid® Low VOC Reducer 3392 Express For optimum reducer selection, refer to TDS # 780.0. ADDITIVES Permasolid® Elastic Additive 9050 MIX RATIO Component 8094 3192 / 3194 / 3196 3394 / 3392 Volume 4 1 +20% ELASTIC CLEAR - PERMASOLID LOW VOC HARDENERS Component Volume 8094 4 9050 +10% 3192 / 3194 / 3196 1 3394 / 3392 +20% Page 1 of 4 Technical Data Sheet – 8094R APPLICATION VISCOSITY Approximately 15 - 16 seconds at 68°F/20°C, DIN 4 POT LIFE Approximately 1 hour at 68°F/20°C when ready to spray. SPECIAL TIPS 1. Permasolid® Low VOC Reducer 3394 Medium is suitable for all temperature ranges (18 - 35°C / 64 - 95 °F). 2. When using Permasolid® Low VOC Reducer 3392 Express, dry for assemble time is reduced to ~1 – 1.5 hours at 68F/ 20C. 3. Using fast hardener, Permasolid® Low VOC Hardener 3192 Fast, can speed up the dry time of the Permasolid® Air Dry Clear Coat 8094 significantly especially when Permasolid® Low VOC Reducer 3392 Express is also being used. Fast hardener should be used when spraying cut-ins and small parts or a single panel and/or in extreme cold conditions. 4. Medium hardener, Permasolid® Low VOC Hardener 3194 Medium, should be used when repairing bumpers and/or 2 to 3 exterior panels. 5. Slow hardener, Permasolid® Low VOC Hardener 3196 Slow, should be used when spraying large exterior panels, a complete repair, and/or in extreme hot conditions. APPLICATION SUBSTRATES Permacron® Base Coat Series 293/295 Permahyd® Hi-TEC 480 Fully cured OEM or existing topcoat (non-reversible) SPRAYGUN SETUP HVLP Approved Transfer Efficiency 1.3-1.4mm 1.2-1.3mm Please refer to gun manufacturer and local legislation for proper spray pressure recommendations. APPLICATION Apply 2 medium to full coats with no intermediate flash-off between coats RECOMMENDED FILM THICKNESS 2.0-2.5 mil dry film thickness DRY TIMES AIR DRYING Drying time at 68°F/20°C: Dust free: Dry for assembly: Dry through: 3394 Medium: 3392 Express: 3394 Medium: 3392 Express: 8 hours 15 to 20 minutes 5 minutes 2.5 to 3 hours 1 to 1.5 hours Page 2 of 4 Technical Data Sheet – 8094R LOW BAKE Flash-off time: Drying time at 110°F/43°C metal temp.: 0-5 minutes 3394 Medium: 10 minutes 3392 Express: 5 minutes PHYSICAL PROPERTIES Coating Category: Clear Coating Max. VOC (AP): 120 g/l; 1.0 lbs/gal Max. VOC (LE): 216 g/l; 1.8 lbs/gal Avg. Gallon Weight: 1089.6 g/l; 9.09 lbs/gal Avg. Weight % Volatiles: 58.6% Avg. Weight % Water: 0.0% Avg. Weight % Exempt Solvent: 48.2% Avg. Volume % Water: 0.0% Avg. Volume % Exempt Solvent: 47.4% Theoretical Coverage: 627 sq. ft. @ 1 mil Theoretical Coverage @ Recommended Film Build: 251 – 314 sq. ft. Coating Category: Elastic Clear Coating Max. VOC (AP): 132 g/l; 1.1 lbs/gal Max. VOC (LE): 240 g/l; 2.0 lbs/gal Avg. Gallon Weight: 1049.9 g/l; 8.76 lbs/gal Avg. Weight % Volatiles: 59.5% Avg. Weight % Water: 0.0% Avg. Weight % Exempt Solvent: 47.2% Avg. Volume % Water: 0.0% Avg. Volume % Exempt Solvent: 47.6% Theoretical Coverage: 597.6 sq. ft @ 1 mil Theoretical Coverage @ Recommended Film Build: 239 – 298 sq. ft. VOC REGULATED AREAS These directions refer to the use of products which may be restricted or require special mixing instructions in VOC regulated areas. Follow mixing usage and recommendations in the VOC Compliant Products Chart for your area. SAFETY AND HANDLING For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS precautions. If mixed with other components, mixture will have hazards of all components. Ready to use paint materials containing isocyanates can cause irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves. Page 3 of 4 Technical Data Sheet – 8094R Any analytical results set forth herein do not constitute a warranty of specific product features or of the product’s suitability for a specific purpose. All products are sold pursuant to our general conditions of sale. We hereby disclaim all warranties and representations, express or implied, with respect to this product, including any warranty of merchantability or fitness for a particular purpose. This product is protected by patent law, trademark law, copyright law, international treaties and/or other applicable law. All rights reserved. Unauthorized sale, manufacturing or use may result in civil and criminal penalties. Revised: January 2016 Page 4 of 4 ©2016 Axalta Coating Systems, LLC and all affiliates. All rights reserved.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021