AEG | L 75670 FL | User manual | AEG L 75670 FL User manual

AEG L 75670 FL User manual
EN User manual
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
/
L 75270 FL
L 75470 FL
L 75670 FL
2
www.aeg.com
CONTENTS
SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PROGRAMMES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
BEFORE FIRST USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
USING THE APPLIANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SETTING AND STARTING A PROGRAMME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
HELPFUL HINTS AND TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CARE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
an
ua
FOR PERFECT RESULTS
ls
.e
u
/
1.
2.
3.
4.
5.
7.
8.
9.
10.
11.
12.
13.
14.
ev
ic
em
Thank you for choosing this AEG product. We have created it to give you impeccable
performance for many years, with innovative technologies that help make life simpler –
features you might not find on ordinary appliances. Please spend a few minutes reading to get
the very best from it.
Visit our website for:
.d
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com
w
w
Register your product for better service:
www.aeg.com/productregistration
w
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
We recommend the use of original spare parts.
When contacting Service, ensure that you have the following data available.
The information can be found on the rating plate. Model, PNC, Serial Number.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
ENGLISH
3
1. SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is
not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions
with the appliance for future reference.
1.1 Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability.
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
/
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door
when it is open.
• If the appliance has a child safety device, we recommend you activate it.
• Cleaning and user maintenance shall not be made by
children without supervision.
1.2 General Safety
• Before maintenance, deactivate the appliance and
disconnect the mains plug from the mains socket.
• Do not change the specification of this appliance.
• Obey the maximum load volume of 7 kg (refer to the
“Programme chart” chapter).
4
www.aeg.com
ls
an
ua
SAFETY INSTRUCTIONS
Electrical connection
2.1 Installation
w
w
.d
ev
ic
em
• Remove all the packaging and the
transit bolts.
• Keep the transit bolts. When you
move the appliance again you must
block the drum.
• Do not install or use a damaged appliance.
• Do not install or use the appliance
where the temperature is less than 0
°C or where it is exposed to the
weather.
• Obey the installation instruction supplied with the appliance.
• Make sure that the floor where you install the appliance is flat, stable, heat
resistant and clean.
• Do not install the appliance where the
appliance door can not be fully
opened.
• Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
• Make sure that there is air circulation
between the appliance and the floor.
• Adjust the feet to have the necessary
space between the appliance and the
carpet.
w
2.
.e
u
/
• If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar
(0,8 MPa)
• The ventilation openings in the base (if applicable)
must not be obstructed by a carpet.
• The appliance is to be connected to the water mains
using the new supplied hose-sets. Old hose sets must
not be reused.
WARNING!
Risk of fire and electrical shock.
• The appliance must be earthed.
• Make sure that the electrical information on the rating plate agrees with
the power supply. If not, contact an
electrician.
• Always use a correctly installed shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the appliance power supply
cable need to be replaced, this must
be carried out by our Service Centre.
• Connect the mains plug to the mains
socket only at the end of the installation. Make sure that there is access to
the mains plug after the installation.
• Do not pull the mains cable to disconnect the appliance. Always pull the
mains plug.
• Do not touch the mains cable or the
mains plug with wet hands.
• Only for UK and Ireland. The appliance has a 13 amp mains plug. If it is
necessary to change the fuse in the
ENGLISH
Water connection
2.3 Care and Cleaning
WARNING!
Risk of injury or damage to the
appliance.
• Before maintenance, deactivate the
appliance and disconnect the mains
plug from the mains socket.
• Do not use water spray and steam to
clean the appliance.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal objects.
an
ua
• Make sure not to cause damage to the
water hoses.
• The appliance is to be connected to
the water mains using the new supplied hose-sets. Old hose sets must
not be reused.
• Before you connect the appliance to
new pipes or pipes not used for a long
time, let the water flow until it is clean.
• The first time you use the appliance,
make sure that there is no leakage.
/
This appliance complies with the
E.E.C. Directives.
.e
u
•
• Do not touch the glass of the door
while a programme operates. The
glass can be hot.
• Make sure that you remove all metal
objects from the laundry.
• Do not put a container to collect possible water leakage under the appliance. Contact the Service to ensure
which accessories can be used.
ls
mains plug, use a 13 amp ASTA (BS
1362) fuse.
5
2.2 Use
ev
ic
em
WARNING!
Risk of injury, electrical shock,
fire, burns or damage to the appliance.
w
w
w
.d
• Use this appliance in a household environment.
• Do not change the specification of this
appliance.
• Obey the safety instructions on the
detergent packaging.
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
2.4 Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the
mains supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent
children and pets to get closed in the
appliance.
3. TECHNICAL INFORMATION
Dimensions
Width / Height / Depth
Total depth
Electrical connection:
Voltage
Overall power
Fuse
Frequency
605 / 850 / 605 mm
640 mm
230-240 V
2200 W
10 A
50 Hz
6
www.aeg.com
Level of protection against ingress of solid particles
and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture
Water supply pressure1)
IPX4
Minimum
0,5 bar (0,05 MPa)
Maximum
8 bar (0,8 MPa)
Cold water
Water supply 2)
Maximum load
Cotton
7 kg
Spin speed
Maximum
1400 rpm
2
3
8
9
ev
ic
em
1
an
ua
4. PRODUCT DESCRIPTION
ls
.e
u
/
1) The appliance works correctly if the water pressure is not less than 0.05 MPa (0.5 bar).
If you can not connect the water inlet hose to the cold water tap of the primary hydraulic
system, connect it to your domestic cold water storage system.
Make sure not to have more than a distance of 5.02 m (16.5 ft) between the appliance
inlet hose and the bottom of the water storage tank.
2) Connect the water inlet hose to a water tap with a 3/4'' thread.
10
5
w
w
w
.d
4
11
6
12
7
1 Worktop
12 Feet for the appliance level
2 Detergent dispenser
3 Control panel
4.1 Child safety device
4 Door handle
5 Rating plate
6 Drain pump
7 Feet for the appliance level
8 Water drain hose
9 Water inlet valve
10 Mains cable
11 Transit bolts
• When you activate this device, you
cannot close the door. This prevents
children or pets to be closed in the
drum. To activate the device, turn it
clockwise, until the groove is horizontal. To deactivate the device, turn it
counterclockwise, until the groove is
vertical.
ENGLISH
7
4.2 Accessories
1
1 Spanner
2
To remove the transit bolts.
2 Plastic caps
.e
u
/
3
ls
4
To close the holes on the rear side
of the cabinet after the removal of
the transit bolts.
3 Anti-flood inlet hose
To prevent possible leakage
4 Plastic hose guide
To connect the drain hose on the
edge of a sink.
If you install the appliance on a plinth,
secure the appliance in the fixing plates.
Follow the instructions supplied with the
kit.
an
ua
4.3 Fixing plate kit
(4055171146)
ev
ic
em
Available from your authorized dealer.
5. CONTROL PANEL
2
3
w
w
.d
1
Cottons
Economy
Super Eco
Cottons
+ Prewash
Extra Silent
Synthetics
w
20 Min. - 3 kg
Quick Intensive
Jeans
+ Prewash
Curtains
Easy Iron
Rinse
Delicates
Spin/Drain
Wool/Silk
On/Off
Temp.
10
Spin
Stains
Extra
Rinse
Time
Save
9
8
7
6
Delay
Start
5
Start/Pause
4
1 On/Off button (On/Off)
6 Time save button
2 Programme knob
3 Display
7 Extra rinse button
4 Start Pause button
9 Spin reduction button
10 Temperature button
5 Delay start button
8 Stain button
www.aeg.com
6.1 On Off button 1
Press this button to activate or deactivate the appliance. A tune sounds when
the appliance is activated.
The AUTO Stand-by function automatically deactivates the appliance to decrease the energy consumption when:
• You do not use the appliance for 5 minutes before you press button 4 .
– All settings are cancelled.
– Press button 1 to activate the appliance again.
– Set again the washing programme
and all possible options.
• After 5 minutes from the end of the
washing programme. Refer to 'At the
end of programme'.
6.2 Programme knob 2
Turn this knob to set a programme. The
related programme indicator comes on.
6.3 Display 3
B
C
D
an
ua
ls
.e
u
/
A
The display shows:
• The maximum temperature of the programme.
B
• The default spin speed of the programme.
• 'No Spin'1) and 'Rinse Hold' symbols.
C
• The display symbols.2)
Description
.d
Symbols
ev
ic
em
A
w
w
Washing phase
w
8
Rinse phases
Spin phase
Child lock
You cannot open the appliance door when the symbol is
on.
You can open the door only when the symbol goes off.
If the programme is completed but the symbol stays on:
• There is water in the drum.
• The 'Rinse Hold' function is on.
Delay start
ENGLISH
D
9
• The programme time
When the programme starts, the time decreases with steps of 1 minute.
• The delay start
When you press the delay start button, the display shows the delay
start time.
• Alarm codes
If the appliance has a malfunction, the display shows alarm codes. Refer to 'Troubleshooting' chapter.
• Err
The display shows this message for some seconds if:
– You set a function that is not applicable for the programme.
– You change the programme while it operates.
The indicator of the Start/Pause button 4 flashes.
When the programme is completed.
.e
u
/
•
6.4 Start/Pause button 4
an
ua
ls
1) Only available for Spin/Drain programme.
2) The symbols appear on the display when the related phase or function is set.
ev
ic
em
Press button 4 to start or interrupt a
programme.
6.5 Delay start button 5
w
w
.d
Press button 5 to delay the start of a
programme from 30 minutes to 20 hours.
6.6 Time save button 6
w
Press the button 6 to decrease the
programme duration.
• Press one time to set 'Shortened duration' for items with daily soil.
• Press two times to set 'Extra Quick' for
items with almost no soil.
Some programmes accept only
one of the two functions.
6.7 Extra rinse button 7
Press button 7 to add rinsing phases to
a programme.
Use this function for persons allergic to
detergents and in areas where the water
is soft.
6.8 Stain button 8
Press button 8 to add the stain phase
to a programme.
Use this function for laundry with hard
stains to remove.
When you set this function, put the stain
.
remover into compartment
This function increases the programme duration.
This function is not available with
a temperature lower than 40° C.
6.9 Spin button 9
Press this button to:
• Decrease the maximum speed of the
spin phase when you set a programme.
The display shows only the spin
speeds available with the set
programme.
• Deactivate the spin phase.
• Activate the 'Rinse Hold' function. Set
this function to prevent fabric creases.
The appliance does not drain the water when the programme is completed.
10 www.aeg.com
Spin phase is off.
'Rinse Hold' function is
on.
6.10 Temperature button 10
Press button 10 to change the default
temperature.
--
= cold water
• To activate the function, press button
10 and button 9 at the same time
until the display shows the symbol
.
• To deactivate the function, press button 10 and button 9 at the same
time until the symbol
goes off.
You can activate the function:
• Before you press the Start/Pause button 4 : the appliance cannot start.
• After you press the Start/Pause button
4 , all the buttons and the programme knob are deactivated.
6.11 Acoustic signals function
6.13 Permanent extra rinse
function
ls
.e
u
/
With this function you can keep the extra
rinse function permanently on when you
set a new programme.
• To activate the function press button
6 and button 5 at the same time
until the indicator of button 7 is on.
• To deactivate the function press button 6 and button 5 at the same
time until the indicator of button 7 is
off.
an
ua
You can hear the acoustic signals when:
• You activate the appliance.
• You deactivate the appliance.
• You press the buttons.
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals, press button 8 and button 7 at
the same time for 6 seconds.
ev
ic
em
If you deactivate the acoustic signals, they continue operate only
when you press the buttons and
when a malfunction occurs.
.d
6.12 Child lock function
w
w
w
This function prevents children to play
with the control panel.
7. PROGRAMMES
Programme
Temperature
Type of load
max. weight of
load
Cycle
description
Functions
Cottons
95° - Cold
White and coloured
cotton with normal
soil.
max. 7 kg
Wash
Rinses
Long spin
SPIN REDUCTION
RINSE HOLD
STAIN
EXTRA RINSE
TIME SAVE1)
Cottons + prewash
95° - Cold
White and coloured
cotton with heavy
soil.
max. 7 kg
Prewash
Wash
Rinses
Long spin
SPIN REDUCTION
RINSE HOLD
STAIN
EXTRA RINSE
TIME SAVE1)
ENGLISH
11
Type of load
max. weight of
load
Cycle
description
Functions
Extra Silent
95° - Cold
White and coloured
cotton with normal
soil.
max. 7 kg
Stop with water in
the drum
Rinses
Long spin
STAIN
EXTRA RINSE
TIME SAVE1)
Synthetics
60° - Cold
Synthetic or mixed
fabric items with
normal level of soil.
max. 3.5 kg
Wash
Rinses
Short spin
SPIN REDUCTION
RINSE HOLD
STAIN
EXTRA RINSE
TIME SAVE1)
Synthetics +
prewash
60° - Cold
Synthetic or mixed
fabric items with
heavy soil.
max. 3.5 kg
Prewash
Wash
Rinses
Short spin
SPIN REDUCTION
RINSE HOLD
STAIN
EXTRA RINSE
TIME SAVE1)
Easy Iron2)
60° - Cold
Synthetic fabric
items with normal
soil.
max. 3.5 kg
Wash
Rinses
Short spin
RINSE HOLD
EXTRA RINSE
TIME SAVE1)
Delicates
40° - Cold
Delicate fabrics as
acrylics, viscose,
polyester items with
normal soil.
max. 3 kg
Wash
Rinses
Short spin
SPIN REDUCTION
RINSE HOLD
STAIN
EXTRA RINSE
TIME SAVE1)
Wool / Silk
40° - Cold
Machine washable
wool. Hand washable wool and delicate fabrics with
«hand washing»
care symbol.
max. 2 kg
Wash
Rinses
Short spin
SPIN REDUCTION
RINSE HOLD
Spin / Drain3)
All fabrics
The maximum load
of the laundry is related to the type of
laundry.
Drainage of the
water
Spin phase at the
maximum speed.
SPIN REDUCTION
NO SPIN
Rinse
Hand washed items. Rinses
Long spin
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
/
Programme
Temperature
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
12 www.aeg.com
Type of load
max. weight of
load
Cycle
description
Functions
Curtains
40° - Cold
Set this programme
to wash curtains. It
adds automatically
the prewash phase
to clean the dust
from the curtains.
Do not put the detergent into the prewash compartment.
max. 2 kg
Prewash
Wash
Rinses
Short spin
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE4)
Jeans
60° - Cold
All items in jeans.
Jersey made items
with hi-tech materials.
max. 7 kg
Wash
Rinses
Short spin
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
TIME SAVE1)
Quick Intensive
60°-40°
Quick washing pro- Wash
gramme, to be used Rinses
for lightly soiled
Long spin
white/fast coloured
cottons and mixed
fabrics.
max. 5 kg
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
20 min. - 3 kg
40°-30°
Cotton and synthet- Wash
ic items with light
Rinses
soil or worn only
Short spin
one time.
SPIN REDUCTION
.d
Mixed fabrics (cotton and synthetic
items).
max. 3 kg
Wash
Rinses
Long spin
SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
White and fast coloured cotton with
normal soil.
max. 7 kg
Wash
Rinses
Long spin
SPIN REDUCTION
NO SPIN
RINSE HOLD
STAIN
EXTRA RINSE
w
w
w
Super Eco5)
Cold
ev
ic
em
an
ua
ls
.e
u
/
Programme
Temperature
Cotton
Economy6)
60° - 40°
1) if you press the button 6 two times (Super Quick function set), we recommend you to
decrease the quantity of the load. It is possible to keep the full load but the washing
results are not good.
2) The wash and spin phase is soft to prevent the creases of the laundry. The appliance
adds some rinses.
3) The default phase of the spin speed is related to cotton items. Set the spin speed. Make
sure that it agrees with the laundry.
4) Set this function to add rinses. With a low spin speed the appliance performs delicate
rinses and a short spin.
5) Set this programme to decrease the time and the consumption of energy and water.
6) Standard programmes for the Energy Label consumption values. According to
regulation 1061/2010, these programmes are respectively the «standard 60° C cotton
ENGLISH
13
programme» and the «standard 40° C cotton programme». They are the most efficient
programmes in terms of combined energy and water consumptions for washing normally
soiled cotton laundry.
Set this programme to have a good washing results and decrease the energy
consumption. The time of the washing programme is extended.
The washing temperature of the washing phase may differ from the temperature
declared for the selected programme.
7.1 Consumption values
.e
u
/
At programme start the display shows the duration programme for the maximum load capacity.
During the washing phase the programme duration is automatically calculated and can greatly be reduced if the laundry load is lower than the maximum load capacity (e.g. Cotton 60°C, maximum load capacity 7 kg, the programme duration exceeds 2 hours; real load 1 kg, the programme duration
don’t reach 1 hour).
When the appliance is calculating the real programme duration a dot blinks
in the display.
Water
consumption (litre)
Approximate
programm
e duration
(minutes)
Remaining
moisture
(%)1)
L
75270
FL
Remaining
moisture
(%)1)
L
75470
FL
Remaining
moisture
(%)1)
L
75670
FL
60
180
53
52
43
an
ua
Energy
consumption
(kWh)
ev
ic
em
Load
(kg)
7
0.10
Cottons 40
°C
7
0.90
60
160
53
52
43
3.5
0.70
50
100
35
35
35
Delicates 40
°C
3
0.50
65
80
35
35
35
Wool/Hand
wash 30 °C
2
0.40
55
60
30
30
30
w
w
w
Cottons 60
°C
.d
Programmes
ls
The data of this table are approximate. Different causes can change the data: the quantity and type of laundry, the water and ambient temperature.
Synthetics
40 °C
Standard cotton programmes
Standard 60
°C cotton
7
0.91
49
207
53
52
43
Standard 60
°C cotton
3.5
0.70
39
155
53
52
43
Standard 40
°C cotton
3.5
0.46
39
150
53
52
43
1) At the end of spin phase.
14 www.aeg.com
Off Mode (W)
Left-On Mode (W)
0.48
0.48
The information given in the charts above are in compliance with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC.
8. BEFORE FIRST USE
1.
To activate the drain system, put 2 litre of water in the main wash compartment of the detergent dispenser.
2. Put a small quantity of detergent in
the main wash compartment of the
Open the water tap.
Connect the mains plug to the mains
socket.
ev
ic
em
1.
2.
an
ua
9. USING THE APPLIANCE
ls
.e
u
/
detergent dispenser. Set and start a
programme for cotton at the highest
temperature without laundry. This
removes all possible dirt from the
drum and the tub.
3.
w
w
w
.d
Press button 1 to activate the appliance.
4. Put the laundry in the appliance.
5. Use the correct quantity of detergent and additives.
6. Set and start the correct programme
for the type of laundry and soil.
9.2 Filling the detergent and
additives
9.1 Loading the laundry
Open the appliance door.
Put the laundry in the drum, one
item at a time. Shake the items before you put them in the appliance.
Make sure not to put too much laundry in the drum.
3. Close the door.
1.
2.
Make sure that no laundry stays between
the seal and the door. There is a risk of
water leakage or damage to the laundry.
ENGLISH
15
The detergent compartment for the prewash phase and the
soak programme.
Add the detergent for prewash and soak before the start of the
programme.
ls
.e
u
/
The detergent compartment for the washing phase.
If you use a liquid detergent, put it immediately before you start
the programme.
an
ua
Liquid additives compartment (fabric conditioner, starch).
Put the product in the compartment before you start the programme.
ev
ic
em
This is the maximum level for the quantity of liquid additives.
The compartment for the stain remover.
Put the product in the compartment and set the stain function
before you start the programme.
w
w
.d
Flap for powder or liquid detergent
Turn it (up or down) in the correct position to use powder or liquid detergent.
w
Always obey the instructions that you find on the packaging of the detergent products.
Check the position of the flap
Pull out the detergent dispenser until it stops.
2. Press the lever down to remove the
dispenser.
1.
16 www.aeg.com
3.
To use powder detergent, turn the
flap up.
4.
To use liquid detergent, turn the
flap down.
6.
Measure out the detergent and the
fabric conditioner.
Carefully close the detergent dispenser. Make sure that the flap
does not cause a blockage when
you close the drawer.
ev
ic
em
5.
an
ua
ls
.e
u
/
With the flap in the position
DOWN:
– Do not use gelatinous or thick
liquid detergents.
– Do not put more liquid detergent than the limit showed in
the flap.
– Do not set the prewash phase.
– Do not set the delay start function.
9.3 Setting and starting a
programme
2.
Turn the programme knob. The related programme indicator comes on.
w
1.
w
w
.d
The appliance adjust automatically the cycle time to the
laundry you have put in the
drum to have perfect washing
results in the minimum necessary time. After approximately 15 minutes from the start of
the programme, the display
shows the new time value.
The indicator of button 4 flashes
with red colour.
3. The display shows the default temperature and spin speed. To change
the temperature and/or the spin
speed, press the related buttons.
4. Set the available functions. The indicator of the set function comes on or
the display shows the related symbol.
5.
Press button 4 to start the programme. The indicator of button 4
is on.
The drain pump can operate for
a short time when the appliance
fills water.
9.4 Interrupt a programme
1.
Press button 4 . The indicator
flashes.
2.
Press button 4 again. The washing
programme continues.
9.5 Cancel a programme
1.
Press button 1 to cancel the programme and to deactivate the appliance.
ENGLISH
2.
Press button 1 again to activate
the appliance. Now, you can set a
new washing programme.
The appliance does not drain the
water.
9.6 Change a function
17
minutes or hours. The related symbols comes on.
2.
Press button 4 , the appliance
starts the countdown of the delay
start.
When the countdown is completed,
the programme starts automatically.
Before you press button 4 to
start the appliance, you can cancel or change the set of the delay
start.
You cannot set the delay start
with the Steam programme.
You can change only some functions before they operate.
1.
Press button 4 . The indicator
flashes.
2. Change the function set.
.e
u
Press button 5 again and again until the display shows the number of
an
ua
ls
1.
/
9.7 Set the delay start
10. SETTING AND STARTING A PROGRAMME
ev
ic
em
10.1 Cancel the delay start
Press button 4 . The related indicator flashes.
2.
Press button 5 again and again until the display shows 0’.
3.
Press button 4 . The programme
starts.
w
w
.d
1.
w
10.2 Open the door
While a programme or the delay start
operates, the appliance door is locked.
To open the appliance door:
1.
Press button 4 . The door lock
symbol in the display goes off.
2. Open the appliance door.
3. Close the appliance door and press
button 4 . The programme or the
delay start continues.
If the temperature and level of
the water in the drum are too
high, the door lock symbol stays
on and you cannot open the
door. To open the door do the
steps that follow:
1. Deactivate the appliance.
2. Wait for some minutes.
3. Make sure that no water is in
the drum.
If you deactivate the appliance, it
is necessary to set the programme again.
10.3 At the end of the
programme
• The appliance stops automatically.
• The acoustic signals operate.
• In the display
comes on.
• The indicator of the Start/Pause button 4 goes off.
• The door lock symbol goes off.
• Press button 1 to deactivate the appliance. After five minutes from the
end of the programme, the energy
saving function automatically deactivates the appliance.
18 www.aeg.com
When you activate the appliance
again, the display show the end
of the last set programme. Turn
the programme knob to set a
new cycle.
• Remove the laundry from the appliance. Make sure that the drum is empty.
• Keep the door ajar, to prevent mildew
and odours.
• Close the water tap.
To drain the water:
If necessary, decrease the spin
speed.
1.
2.
Press the Start/Pause button 4 .
The appliance drain the water and
spin.
3. When the programme is completed
and the door lock symbol goes off,
you can open the door
4. Deactivate the appliance.
The appliance drain and spin automatically after approximately
18 hours.
11.1 The laundry load
w
w
.d
ev
ic
em
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are
on the laundry care labels.
• Do not wash together white and coloured items.
• Some coloured items can discolour
with the first wash. We recommend
that you wash them separately for the
first times.
• Button up pillowcases, close zippers,
hooks and poppers. Tie up belts.
• Empty the pockets and unfold the
items.
• Turn inside out multilayered fabrics,
wool and items with painted illustrations.
• Remove hard stains.
• Wash with a special detergent heavy
soil stains.
• Be careful with the curtains. Remove
the hooks or put the curtains in a
washing bag or pillowcase.
• Do not wash in the appliance :
– Laundry without hems or with cuts
– Underwired bras.
– Use a washing bag to wash small
items.
w
ls
an
ua
11. HELPFUL HINTS AND TIPS
.e
u
/
The washing programme is
completed, but there is water in the
drum:
– The drum turns regularly to prevent
the creases in the laundry.
– The door stays locked.
– You must drain the water to open the
door.
• A very small load can cause balance
problems with the spin phase. If this
occurs, adjust manually the items in
the tub and start the spin phase again.
11.2 Stubborn stains
For some stains, water and detergent is
not sufficient.
We recommend that you remove these
stains before you put the items in the
appliance.
Special stain removers are available. Use
the special stain remover that is applicable to the type of stain and fabric.
11.3 Detergents and additives
• Only use detergents and additives
specially made for washing machines.
• Do not mix different types of detergents.
• To help the environment, do not use
more than the correct quantity of detergent.
• Obey the instructions that you find on
the on packaging of these products.
• Use the correct products for the type
and colour of the fabric, the programme temperature and the level of
soil.
ENGLISH
• If you use liquid detergents, do not set
the prewash phase.
• If your appliance has not the detergent dispenser with the flap device,
add the liquid detergents with a dosing ball.
11.4 Water hardness
If the water hardness in your area is high
or moderate, we recommend that you
use a water softener for washing machines. In areas where the water hardness is soft it is not necessary to use a
water softener.
19
To know the water hardness in your area,
contact your local water authority.
Obey the instructions that you find on
the packaging of the products.
Equivalent scales measure the water
hardness:
• German degrees (°dH).
• French degrees (°TH).
• mmol/l (millimol for each litre - international unit for the hardness of water).
• Clarke degrees.
Water hardness table
Water hardness
Type
°dH
°T.H.
1
soft
0-7
0-15
2
medium
8-14
3
hard
15-21
4
very hard
> 21
.e
u
/
Level
Clarke
0-1.5
0-9
16-25
1.6-2.5
10-16
26-37
2.6-3.7
17-25
> 37
>3.7
>25
ev
ic
em
an
ua
ls
mmol/l
12. CARE AND CLEANING
w
w
.d
WARNING!
w
Disconnect the appliance from the mains
supply before you clean it.
12.1 Descaling
The water we use contains limescale. If it
becomes necessary, use a water softener
to remove limescales.
Use a special product made for washing
machines. Obey the instructions that you
find on the packaging of the manufacturer.
Do this separately from the laundry
wash.
12.2 External cleaning
Clean the appliance only with soap and
warm water. Fully dry all the surfaces.
CAUTION!
Do not use alcohol, solvents or
chemical products.
12.3 Maintenance wash
With the low temperature programmes it
is possible that some detergent stays in
the drum. Make regularly a maintenance
wash. To do this:
• Empty the laundry from the drum.
• Set the hottest cotton wash programme
• Use a correct quantity of powder detergent with biological properties.
After each wash, keep the door open for
a while to prevent mould and to let unpleasant smells go out.
20 www.aeg.com
12.4 Door seal
Regularly examine the seal and remove
all objects from the inner part.
12.5 Drum
.e
u
/
Regularly examine the drum to prevent
limescale and rust particles.
Only use special products to remove rust
particles from the drum.
To do this:
• Clean the drum with special product
for stainless steel.
• Start a short programme for cotton at
the maximum temperature with a
small quantity of detergent.
ls
12.6 Detergent dispenser
an
ua
To clean the dispenser:
1.
2.
Press the lever.
Pull the dispenser out.
3.
Remove the top part of the liquid
additive compartment.
Clean all the parts with water.
ev
ic
em
1
w
w
w
.d
2
4.
5.
6.
Clean the dispenser recess with a
brush.
Put back the dispenser in the recess.
ENGLISH
21
• The display shows an alarm code because of the problem with water drain.
12.7 Drain pump
Regularly examine the drain
pump and make sure that it is
clean.
WARNING!
1. Disconnect the mains plug
from the mains socket.
2. Do not remove the filter
while the appliance operates. Do not clean the drain
pump if the water in the appliance is hot. The water
must be cold before you
clean the drain pump.
Clean the pump if:
• The appliance does not drain the water.
• The drum cannot turn.
• The appliance makes an unusual noise
because of the blockage of the drain
pump.
Open the drain pump door.
2.
.e
u
/
1.
ls
To clean the drain pump:
3.
4.
Put a container below the recess of
the drain pump to collect the water
that flows out.
Press the two levers and pull forward the drainage duct to let the
water flow out.
w
w
w
.d
ev
ic
em
an
ua
Pull the flap out to remove it.
1
5.
6.
2
When the container is full of water,
put the drainage duct back again
and empty the container. Do steps 4
and 5 again and again until no more
water flows out from the drain
pump.
Pull back the drainage duct and turn
the filter to remove it.
22 www.aeg.com
7.
Remove fluff and objects from the
pump.
8.
Make sure that the impeller of the
pump can turn. If this does not occur, contact the service centre.
9.
Clean the filter under the water tap
and put it back in the pump into the
special guides.
10. Make sure that you tighten correctly
the filter to prevent leakages.
11. Put the flap back and close the drain
pump door.
an
ua
ls
.e
u
/
2
ev
ic
em
1
12.8 The inlet hose filter and
the valve filter
• The indicator of button 4 flashes and
the display shows the related alarm.
Refer to 'Troubleshooting'.
It could be necessary to clean the filters
when:
• The appliance does not fill with water.
• The appliance fills with the water for a
long time.
w
w
.d
WARNING!
Disconnect the mains plug from
the mains socket.
w
To clean the water inlet filters:
Close the water tap.
Remove the water inlet hose from
the water tap.
3. Clean the filter in the inlet hose with
a stiff brush.
1.
2.
ENGLISH
4.
5.
6.
Remove the inlet hose behind the
appliance.
Clean the filter in the valve with a
stiff brush or a towel.
Install again the inlet hose. Make
sure that the couplings are tight to
prevent leakages.
Open the water tap.
.e
u
/
7.
23
45°
0 °C, remove the remaining water from
the inlet hose and the drain pump.
1. Disconnect the mains plug from the
mains socket.
2. Close the water tap.
3. Remove the water inlet hose
4. Put the two ends of the inlet hose in
a container and let the water flow
out of the hose.
5. Empty the drain pump. Refer to the
emergency drain procedure
6. When the drain pump is empty, install the inlet hose again.
an
ua
12.9 Emergency drain
ls
20°
w
w
w
.d
ev
ic
em
Because of a malfunction, the appliance
cannot drain the water.
If this occurs, do steps (1) through (6) of
'To clean the drain pump'.
If necessary, clean the pump.
Put the drainage duct back and close the
drain pump flap.
When you drain the water with the emergency drain procedure, you must activate again the drain system:
1. Put 2 litres of water in the main wash
compartment of the detergent dispenser.
2. Start the programme to drain the
water.
12.10 Frost precautions
If the appliance is installed in an area
where the temperature can be less than
WARNING!
Make sure that the temperature
is more than 0 °C before you use
the appliance again.
The manufacturer is not responsible for damages caused by low
temperatures.
13. TROUBLESHOOTING
The start of the appliance does not occur or it stops during operation.
First try to find a solution to the problem
(refer to the table). If not, contact the
service centre.
With some problems, the acoustic
signals operate and the display shows
an alarm code:
•
- The appliance does not fill with
water.
24 www.aeg.com
•
•
- The appliance does not drain
the water.
•
- The anti-flood device is on.
WARNING!
Deactivate the appliance before
you do the checks.
- The appliance door is open or
not closed correctly.
Problem
Possible cause
Possible solution
The appliance
does not fill with
water.
The water tap is closed.
Open the water tap.
The water inlet hose is
damaged.
Make sure that the water inlet
hose has no damages.
The filters in the water
inlet hose is blocked .
Clean the filters. Refer to 'Care
and cleaning'.
Contact your local water authority.
an
ua
The water pressure is
too low.
Make sure that the connection
is correct.
ls
The connection of the
water inlet hose is not
correct.
.e
u
/
The water tap is blocked Clean the water tap.
or is furred with limescale.
ev
ic
em
The appliance
The water drain hose is
does not drain the damaged.
water.
The filter of the drain
pump is blocked.
Clean the filter of the drain
pump. Refer to 'Care and cleaning'.
The connection of the
water drain hose is not
correct.
Make sure that the connection
is correct.
A washing programme
without the drain phase
is set.
Set the drain programme.
The function Rinse &
Hold is on.
Set the drain programme.
.d
w
w
w
Make sure that the water drain
hose has no damages.
The appliance
door is open or
not closed correctly.
Close the door correctly.
The anti-flood device is on.
• Disconnect the appliance.
• Close the water tap.
• Contact the service centre.
The spin phase
does not operate.
The spin phase is off.
Set the spin programme.
ENGLISH
There is water on
the floor.
Clean the filter of the drain
pump. Refer to 'Care and cleaning'.
Balance problems with
the laundry load.
Adjust manually the items in the
tub and start the spin phase
again.
The mains plug is not
connected in the mains
socket.
Put in the mains plug.
Blow out fuse in the
household fuse box.
Replace the fuse.
You did not press button 4 .
Press button 4 .
The delay start is set.
To start immediately the programme, cancel the delay start.
The Child Lock function
is activated.
Deactivate the Child Lock function.
.e
u
/
Possible solution
The filter of the drain
pump is blocked.
ls
The programme
does not start.
Possible cause
an
ua
Problem
25
Leakages from the couplings of the water hoses.
Make sure that the couplings
are tight.
The water drain hose is
damaged.
Make sure that the water inlet
hose has no damages.
The washing programme is in operation.
Let the washing programme
end.
There is water in the
drum.
Set the drain or the spin programme.
w
w
w
.d
You cannot open
the appliance
door.
ev
ic
em
Leakages from the drain Make sure that the drain pump
pump.
filter is tight.
The appliance
makes an unusual
noise.
Incorrect level of the ap- Adjust the level of the applipliance.
ance. Refer to 'Installation'.
You did not remove the
packaging and/or the
transit bolts.
Remove the packaging and/or
the transit bolts. Refer to 'Installation'.
The load is very small.
Add more laundry in the drum.
The appliance fills The end of the drain
with water and
hose is too low.
drain immediately.
The washing results are not satisfactory.
Make sure that the drain hose is
in the correct position.
The detergent you used Increase the detergent quantity
was not sufficient or cor- or use a different one.
rect.
26 www.aeg.com
Possible cause
Possible solution
You did not remove the
stubborn stains before
you wash the laundry.
Use special products to remove
the stubborn stains.
Incorrect temperature
was set.
Make sure that you set the correct temperature.
Too much laundry load.
Decrease the laundry load.
After the check, activate the appliance.
The programme continues from the
point of interruption.
If the problem occurs again, contact the
service centre.
If the display shows other alarm codes,
contact the service centre.
.e
u
/
14. INSTALLATION
14.1 Unpacking
ls
Problem
Use the gloves. Remove the external
film. If necessary, use a cutter.
2.
3.
Remove the cardboard top.
Remove the polystyrene packaging
materials.
w
w
w
.d
ev
ic
em
an
ua
1.
ENGLISH
Remove the internal film.
5.
Open the door. Remove the polystyrene piece from the door seal
and all the items from the drum.
an
ua
ls
.e
u
/
4.
27
Put one of the polystyrene packaging elements on the floor behind
the appliance. Carefully put down
the appliance with the rear side on
it. Make sure not to damage the hoses.
7.
Remove the polystyrene protection
from the bottom.
Pull up the appliance in vertical position.
w
w
w
.d
ev
ic
em
6.
8.
1
2
28 www.aeg.com
9.
Remove the power supply cable and
the drain hose from the hose holders.
10. Remove the three bolts. Use the key
supplied with the appliance.
an
ua
ls
.e
u
/
11. Pull out the plastic spacers.
You can find these caps in the user
manual bag.
w
w
w
.d
ev
ic
em
12. Put the plastic caps in the holes.
WARNING!
Remove all the packaging and
the transit bolts before you install
the appliance.
We recommend that you keep
the packaging and the transit
bolts for when you move the appliance.
ENGLISH
29
14.2 Positioning and levelling
• Install the appliance on a flat hard
floor.
• Make sure that carpets do not stop
the air circulation below the appliance.
• Make sure that the appliance does not
touch the wall or other units
• Loosen or tighten the feet to adjust
the level. A correct adjustment of the
appliance level prevents the vibration,
noise and the movement of the appliance when in operation.
.e
u
/
x4
ev
ic
em
an
ua
ls
• The appliance must be level and stable.
.d
CAUTION!
Do not put cardboard, wood or
equivalent materials below the
appliance feet to adjust the level.
w
w
w
Make sure that there is sufficient
access after the installation for
possible repairs by a qualified
person.
Installation on suspended
flooring
Suspended wooden floors are particularly susceptible to vibration. To help prevent vibration we recommend you place
a waterproof wood panel, at least 15 mm
thick under the appliance, secured to at
least 2 floor beams with screws, the
wood panel must extend beyond the
front feet.
If possible install the appliance in one of
the corners of the room, where the floor
is more stable
30 www.aeg.com
14.3 The inlet hose
• Connect the hose to the appliance.
Turn the inlet hose only left or right.
Loose the ring nut to set it in the correct position.
45
.e
u
/
20
O
O
ls
• Connect the water inlet hose to the
cold water tap with 3/4 thread.
.d
ev
ic
em
an
ua
CAUTION!
Make sure that there are no leaks
from the couplings.
w
w
w
Do not use an extension hose if
the inlet hose is too short. Contact the service centre for the replacement of the inlet hose.
Water pressure
The appliance works correctly if the water pressure is not less than 0.05 MPa
(0.5 bar).
If you can not connect the water inlet
hose to the cold water tap of the primary
hydraulic system, connect it to your domestic cold water storage system.
Make sure not to have more than a distance of 5.02 m (16.5 ft) between the appliance inlet hose and the bottom of the
water storage tank.
ENGLISH
31
Water-stop device
The inlet hose has a water stop device.
This device prevents water leaks in the
hose because of its natural ageing. The
red sector in the window «A» shows this
fault .
If this occur, close the water tap and
contact the service centre to replace the
hose.
A
14.4 Water drainage
There are different procedures to connect the drain hose:
• On the edge of a sink.
• Make sure that the plastic guide cannot move when the appliance drains.
Attach the guide to the water tap or
the wall.
w
w
w
.d
ev
ic
em
an
ua
ls
.e
u
/
With the plastic hose guide.
• To a stand pipe with vent-hole.
Refer to the illustration. Directly into a
drain pipe at a height of not less than
60 cm (23.6”) and not more than 100
cm (39.3”). The end of the drain hose
must always be ventilated , i.e. the inner diameter of the drainpipe (min. 38
mm — min. 1.5”) must be larger than
the external diameter of the drain
hose.
32 www.aeg.com
• If the end of the drain hose is this (see
the drawing), you can push it directly
into the stand pipe.
Without the plastic hose guide.
an
ua
ls
.e
u
/
• To a sink spigot.
Refer to the illustration. Put the drain
hose in the spigot and tighten it with a
clip. Make sure that the drain hose
makes a loop to prevent that remaining particles go in the appliance from
the sink.
.d
ev
ic
em
• Directly to a built-in drain pipe in the
room wall and tighten it with a clip.
w
w
w
You can extend the drain hose to
maximum 400 cm. Contact the
service centre for the other drain
hose and the extension.
15. ENVIRONMENT CONCERNS
Recycle the materials with the
symbol . Put the packaging in
applicable containers to recycle it.
Help protect the environment and
human health and to recycle waste
of electrical and electronic
appliances. Do not dispose
appliances marked with the symbol
with the household waste. Return the
product to your local recycling
facility or contact your municipal
office.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising