Panorama Datascope Quick Reference Guide ®

Panorama Datascope Quick  Reference  Guide ®
Q u i c k R e fe re n ce G u i d e
Datascope
Datascope
® T E L E PAC K– 6 0 8® S p O 2 M O D U L E
PanoramaPanorama
Panorama_Telepk QRG_0003_rB.indd 1
3/18/10 3:13:37 PM
Note: The Panorama Telepack SpO2 Quick Reference
Guide is not intended as a replacement to the
Operating Instructions. Prior to operating equipment,
the user must be familiar with the Operating
Instructions Manual contents. This document is a
guideline only to be used as an aid to comprehensive
Inservice Training.
Note: The Panorama Telepack SpO2 module can be
used with the Panorama Telepack-608 device and/or
the Panorama Telepack-2.4 GHz device.
Panorama® is a registered trademark of Mindray DS USA, Inc.
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 2
3/18/10 3:13:37 PM
Table of Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Print
Real-Time Waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Patient
Removing
Demographics
Cleaning Plug
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . from SpO2 Module. . . . . . . . . . . . . . 2
1
Transfer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enabling the SpO2 module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1
Standby
Installing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . the SpO2 patient cable and sensor. . . . . . . . . . . . . . 5
2
Discharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Displaying the SpO2 waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2
Retrieve
Discharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printing Real
Time SpO2 Waveform. . . . . . . . . . . . . . . . . . . . . . . 9
3
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Patient Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Patient
ViewingAlarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
and Printing Trends. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
To
Mute and
Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Viewing
Printing Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Latched
DisablingAlarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
the SpO2 Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Viewing
Trends. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaningand
the Printing
SpO2 Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Viewing
andAsked
Printing
Events. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Frequently
Questions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Viewing and Printing Disclosure. . . . . . . . . . . . . . . . . . . . . . . . . 18
Viewing and Printing ST Data. . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Paging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 3
3/18/10 3:13:37 PM
Panorama_Telepk QRG_0003_rB.indd 4
3/18/10 3:13:37 PM
Panorama®
Telepack-608 SpO2 Quick Reference Guide
Overview
The Panorama Telepack with the SpO2 Module
measures functional oxygen saturation of the arterial
hemoglobin (% SpO2) and pulse rate (BPM) for the
adult patient. The following information is available
at the Panorama Central Station, ViewStation, and/or
Interactive Workstation:
1. SpO2 Waveform
2. SpO2 numeric data
3. Numeric Pulse Rate
Removing Cleaning Plug from SpO2 Module:
To remove cleaning plug, pull the tip of the top arm from
the recess in the inside of SpO2 module and pull up.
Reminder: Place cleaning plug back into SpO2 module
when module is not in use.
Enabling the SpO2 module:
To activate the SpO2 module on the Panorama Telepack,
a.Remove the flexible cover on bottom of the
Panorama Telepack
b.Remove cleaning plug from SpO2 module
c.Place flexible cover on bottom of SpO2 module
d.Turn Panorama Telepack OFF by rotating battery
door counterclockwise
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 5
1
3/18/10 3:13:37 PM
Panorama®
Telepack-608 SpO2 Quick Reference Guide
e.Align SpO2 module with Panorama Telepack and
slide SpO2 module onto telemetry pack until an
audible “click” is heard
f.Ensure ECG lead wires set is connected to
Panorama Telepack
g.Turn Panorama Telepack on by rotating battery
door clockwise
Installing the SpO2 patient cable and sensor:
To connect the SpO2 patient cable and sensor to the
SpO2 Module,
a.Connect SpO2 patient cable on the bottom of the
SpO2 module
b.Press to secure the SpO2 patient cable into the
channels on the back of the SpO2 module
c.Attach disposable SpO2 sensor to patient cable
(if applicable)
Displaying the SpO2 waveform:
To display the Panorama Telepack SpO2 waveform
on the main display of the Panorama Central Station,
ViewStation, or Interactive Workstation,
a.Select PATIENT SETUP menu button
b.Select patient tile by touching the digital data area
or the waveform area of the tile
c.Select DISPLAY tab
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 6
2
3/18/10 3:13:37 PM
Panorama®
Telepack-608 SpO2 Quick Reference Guide
d.Select waveform 2
e.Choose Pleth waveform from the waveform list box
f.Choose SELECT to confirm
Printing Real Time SpO2 Waveform:
To select and print an All Strips Report at the
Panorama Central Station, ViewStation, and/or
Interactive Workstation containing the SpO2 waveform,
a.Select PATIENT SETUP menu button
b.Select patient tile by touching the digital data area
or the waveform area of the tile
c.Select PRINT SETUP tab
d.Select Pleth waveforms for printing
• A ✓ in the waveform box indicates the waveform
is configured to print
e. Select REC adjacent to the patient tile
Patient Alarms:
The Patient Alarms tabs at the Panorama Central Station
and Interactive Workstation* allow the user to configure
alarm limits and responses of the Panorama Central
Station when an alarm violation occurs.
To adjust the patient’s SpO2 alarm limits at Panorama
Central Station or Interactive Workstation*,
a.Select PATIENT ALARMS menu button
* Optional
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 7
3
3/18/10 3:13:37 PM
Panorama®
Telepack-608 SpO2 Quick Reference Guide
b.Select patient tile by touching the digital data
area or the waveform area of the tile
c.Select ALARM LIMITS tab
d.Select the SpO2 Parameter using the ➞ or ➞
buttons
e.Select the High or Low SpO2 alarm limit button
on the slider
f.Use the up and down arrows or drop and drag
the scroll box in the slider control to change the
limit to the desired value
To adjust a patient’s SpO2 alarm responses on the
Panorama Central Station from the Panorama Central
Station and/or Interactive Workstation*,
a.Select PATIENT ALARMS menu button
b.Select patient tile by touching the digital data
area or the waveform area of the tile
c.Select ALARM RESPONSES tab
d.Select and highlight the SpO2 parameter
e.Select
• Priority - Adjusts the importance of the alarm.
The lower the priority the higher the severity.
• Print On Alarm - Determines if an automatic
Print on Alarm Report is produced upon the
alarm condition.
* Optional
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 8
4
3/18/10 3:13:37 PM
Panorama®
Telepack-608 SpO2 Quick Reference Guide
• Save To Event - Determines if the alarm event
is saved in the Events tab to be retrieved at a
later time.
• Page On Alarm* - Determines if the alarm event
sends a page request to the assigned pager(s).
Viewing and Printing Trends:
The List Trends Tab at the Panorama Central Station,
ViewStation, and Interactive Workstation allows viewing
and printing of all available vital sign information in list
and graphic formats.
To view and print List Trends at Panorama Central
Station, ViewStation, and/or Interactive Workstation,
a.Select VIEW adjacent to the patient tile
b.Select TRENDS tab to view the trend list
c.Select PRINT menu button
• PRINT CURRENT to print one page of
trended information
• PRINT _ HOUR to print a configured
interval of trended information
Viewing and Printing Events:
The Events Tab at the Panorama Central Station,
ViewStation, and Interactive Workstation stores configured
physiologic and technical events on a patient.
* Optional
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 9
5
3/18/10 3:13:37 PM
Panorama®
Telepack-608 SpO2 Quick Reference Guide
To view Events at the Panorama Central Station,
Viewstation, and/or Interactive Workstation,
a. Select VIEW adjacent to the patient tile
b. Select EVENTS tab to view the Event List
To view and print an SpO2 event in the Event List at
the Panorama Central Station, Viewstation, and/or
Interactive Workstation,
a. Select VIEW adjacent to the patient tile
b. Select EVENTS tab to view the event list screen
c. Select and highlight the SpO2 event
d. Select VIEW WAVEFORM sidebar button
e. Select PRINT to print the 20 second stored event
Note: The waveforms printed are determined by the
patient’s PRINT SETUP Tab.
Disabling the SpO2 Module:
To remove SpO2 module from Panorama Telepack,
a.Turn Panorama Telepack OFF by rotating the
battery door counterclockwise
b.Press the blue button on the right side of
the module until an audible “click” is heard
(Disengaging the module)
c.Remove the Panorama Telepack from the SpO2
module
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 10
6
3/18/10 3:13:37 PM
Panorama®
Telepack-608 SpO2 Quick Reference Guide
d.Replace flexible cover (from bottom of SpO2
module) over connection site on bottom of
Panorama Telepack
e.Turn Panorama Telepack on by rotating the battery
door clockwise to continue ECG monitoring
f.Replace cleaning plug over connection site on
inside of SpO2 module
Cleaning the SpO2 Module:
To clean the SpO2 module:
a.Place cleaning plug on the connector located in the
inside of the SpO2 module
b.Press down on the cleaning plug while angling the
top of arm of the plug into the circular recess
c.Refer to Panorama Central Station Operator manual
for approved cleaning solutions
Frequently Asked Questions
The SpO2 module appears connected but the SpO2
digital data is not being displayed. What could be the
issue?
a.SpO2 module attached with the Panorama
Telepack on
• Turn off the Panorama Telepack, attach the
SpO2 module, and turn on to “initialize” the
SpO2 module
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 11
7
3/18/10 3:13:37 PM
Panorama®
Telepack-608 SpO2 Quick Reference Guide
b.ECG lead wires disconnected
• Attach ECG lead wires sets to Panorama Telepack
c.SpO2 module not completely connected
• Turn off the Panorama Telepack by rotating
battery door counterclockwise
• Disable the SpO2 module by pressing the
release button
• Align SpO2 module with Panorama Telepack
and slide module onto telemetry pack until an
audible “click” is heard
• Ensure ECG lead wires set is connected to
Panorama telepack
• Turn Panorama Telepack on by rotating battery
door clockwise
d.SpO2 patient cable and sensor connection issue
• Verify connection on bottom of SpO2 module
• Verify connection of sensor with SpO2 patient
cable (disposable probe)
• Verify SpO2 sensor is attached
• Ensure red light is illuminated on sensor
i.Replace patient cable and/or sensor if not
illuminated
ii.Replace batteries in Panorama Telepack
e.Display Tab is not configured to display SpO2
• Select PATIENT SETUP menu button
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 12
8
3/18/10 3:13:37 PM
Panorama®
Telepack-608 SpO2 Quick Reference Guide
• Select patient tile by touching the digital
data area or the waveform area of the tile
• Select DISPLAY Tab
• Verify SpO2 is assigned in digital data tile
i.If unassigned select digital data tile and
select SpO2 from the parameter list box
• Choose SELECT to confirm
The batteries on the Panorama Telepack need to be
replaced. Does the SpO2 module need to be removed
prior to battery replacement?
No. The “Communication Lost” message will be displayed
on the Panorama Central Station during the battery
exchange and the SpO2 digital/waveform monitoring will
resume once the new batteries are inserted turning the
Panorama Telepack back on.
The SpO2 module needs to be moved to another
Panorama Telepack to be used. Can it be disconnected
while the Panorama Telepack is on?
It is highly recommended the Panorama Telepack be
turned off prior to disengaging the SpO2 module to
prevent any potential problems. If the SpO2 module
is removed while the Panorama Telepack is still on a
“SpO2 Communication Error” message is displayed on
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 13
9
3/18/10 3:13:37 PM
Panorama®
Telepack-608 SpO2 Quick Reference Guide
the patient tile at the Panorama Central Station and the
SpO2 tile is removed.
The heart rate color in the patient tile has changed while
the SpO2 module is being used. What is the reason?
A patient’s heart rate is obtained (sourced) from the ECG or
the SpO2 when using a Panorama Telepack. If an ECG lead
off condition occurs a “Lead OFF” message is displayed
in the patient tile on the Panorama Central Station. If the
heart rate is unobtainable from the ECG, the heart rate is
automatically obtained from the SpO2. The heart rate color
will change to the SAME color as the SpO2 parameter to
indicate this shift in the heart rate source.
Note: The arrhythmia package is temporarily disabled
while the heart rate is being obtained from the SpO2
parameter.
Are there any other reminders or special considerations
for the Panorama Telepack SpO2 module?
a.Remove the SpO2 module prior to defibrillating a
patient
b.Remove the SpO2 module prior to entering the MRI
environment
c.Insert SpO2 module cleaning plug prior to cleaning
the SpO2 module to maintain its water resistance
rating
P/N: 0077-00-0003-01 Rev B
Panorama_Telepk QRG_0003_rB.indd 14
10
3/18/10 3:13:37 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement