OWNER MANUAL

PLEASE SAVE THIS MANUAL

FOR FUTURE REFERENCE

TM

FOOT-SPA

Chair 9700

Chair 9600

TM TM TM

Cleanjet , La Lili ,Gulfstream Plastic are trademarks of Gulfstream Plastic Ltd. Patent

©

2008 All rights reserved.

Design and Specifications are subject to change without notice

Table of Contents

Owner Manual

Safety and Precautions

Identifying Parts

Foot-spa Clearance

INSTALLATIONS

Attaching Seat

Jet Assembly

Plumbing Connections

Operations and Use

Cleaning & Maintenance

Warranty & Service

1

2-3

4

5

6-7

8

9-11

12

13

SAFETY & PRECAUTION

Thank you for purchasing the La Lili spa from Gulfstream Plastics Ltd. Please carefully read instructions before installing the spa. Carefully follow the instructions, your spa will give you years of beauty and service.

1

This product is to be connected to a branch circuit outlet protected by a Class A GROUND FAULT CIRCUIT

INTERRUPTER (GFCI), and the GFCI shall be tested regularly for continued protection and correct operation. If a Class A GFCI protected outlet is not available, DO NOT USE THIS PRODUCT! Please contact a licensed electrician for installation of a Class A GFCI according to local electric codes, or equivalent.

!

Warning

THIS PRODUCT IS FOR IN DOOR USE ONLY

DISCONNECT POWER SUPPLY CORD BEFORE SERVICING AND CLEANING

Foot-spa must be installed by a licensed plumber and electrician in accordance with local codes.

Plumbing and Electrical Installation instructions must be adhered to in order for the warranty to be in effect and to insure the utmost in safety. Chair and spa have a maximum seating capacity of 350 pounds.

BASIC PRECAUTIONS SHOULD ALWAYS BE OBSERVED, INCLUDING THE FOLLOWING:

1. Read and follow all instructions

2. DANGER. To reduce the risk of injury, do not permit children to use this unit unless they are supervised at all

times

3. Use this unit only for its intended use as described in this manual. Do not use attachments that are not

Recommended by the manufacturer.

4. Never drop or insert any object into any opening.

5. Do not block jets during whirlpool operation.

6. The unit must be connected to an electrical supply circuit that is protected by a ground fault circuit interrupter.

7. The clean jet motor is magnetically driven and is insulated twice. Therefore it does not require to be bonded.

Save these instructions

!

Warning

1. Excessive water temperature is dangerous and should be checked BEFORE use.

2. Maximum temperature of the water should never exceed 100 degrees F.

3. Always enter and exit the Foot Spa slowly and carefully.

4. NEVER bring and / or operate any electrical devices into or near the Foot Spa.

2

IDENTIFY YOUR FOOT-SPA

Front

11

6

Back

4

5

3

10

2

1

1. Tub & Glass Insert

2. Adjustable Footrest

3. Seat Cushion

4. Flip-out Manicure Tray

5. Back Cushion & Massage

6. Headrest Pillow

7. Wooden Armrest

8. Hand Spray

9. Front Control Panel

10. Drain

11. Jet 2X

12. Drain Control

13. Water Control

14. Jet Control

9

Control Panel

12

13

14

7

8

IDENTIFY YOUR FOOT-SPA

2

Reclining

SEAT OPERATION

1

Armrest can be raised up/down

3

3

Sliding

SPA DIMENSION

43’’

15’’

32

’’

2

7’’

FOOT-SPA CLEARANCE

Wall

WALL CLEARANCE

4

16’’

TYPICAL FOOT-SPAS

Center

Foot-spa #1

16’’

60’’

28’’

Center

16’’

Foot-spa #2

Clearance

60’’

INSTALLATIONS

Attaching The Seat to The Base

Attach trays or remote stand to armrest with screws provided

5

Align the seat with the pre-drilled holes on the base then tightly secure with the nuts and bolts provided.

6

INSTALLATIONS

Cleanjet Components

Jet Cover

Jet Motor & Housing

Cleanjet SL Components

Suction Control Screen

(Optional)

Jet Cover Inner Cover

Jet Motor & Housing

2

1

7

INSTALLATIONS

Cleanjet Cover Removal and Installation

Cleanjet

1

2

The Open

Align fingers to the open, turn counter-clockwise and pull in the arrow direction to remove jet cover

Align jet cover on the jet housing then turn clockwise to install jet cover

Cleanjet-SL

(Refer to CleanJet-SL Assembly for more details)

Gently pull out the jet cover in the arrow direction to remove then carefully remove the suction control screen, the jet inner cover

Align and snap the jet inner cover, the suction control screen on the jet cover. Then snap on the jet cover in th arrow direction to the housing to close

INSTALLATIONS

Plumbing Connections

Gravity Drain

8

Power Drain

Drain Pump

Hot & Cold ½” Fitting

½”

’ Fitting

Not provided

P-Trap

1. Discharge pump may be connected to an existing sink drain or floor drain. It can also pump up to 7 ft high, but this

will increase the length of the drain time. The drain connection is at the rear of the unit by a ½” fitting.

2. Gravity drain uses a standard gravity drain. A floor drain is recommended. Connection via a P-Trap is supplied.

3. Hot and cold water supply connections are located at the rear of the unit (½” fittings).

Please be advised that the hot and cold water supply lines are not fitted with optional back flow Preventers unless

ordered at initial sale.

4. Have a qualified licensed electrician to install the wiring according to local codes.

The Cleanjets are 1/10 hp, 120V, 1.2 AMP 60OHZ. A 15 amp GFI protected circuit must be used to supply power to

the unit. The roller back massage chair uses a 115V supply.

5. Spa base should be anchored securely to the floor. The base may be anchored through

the opening in the back of the base wherever access is convenient for the installer.

FAILURE TO ANCHOR THE BASE MAY RESULT IN PERSONAL INJURY OR DAMAGE TO THE UNIT.

DAMAGE AS A RESULT WILL VOID THE WARRANTY.

9

OPERATIONS & USE

Control Panel

Drain Control

Jet On/Off

1. To fill water:

The foot-spa is provided with a single hot and cold mixing valve located on the front of your spa.

This is a pressure balance valve that requires you to lift the handle to start the water flow and to adjust to the

temperature that is desired. The clean jet motor must be completely submerged in water.

CAUTION: DO NOT USE FOAMING, SUDSING OR MINERAL OIL BASED ADDITIVES IN THE WATER.

2. To start whirlpool:

Press the button that is situated next to the water fill lever. This will start your Clean Jet motor. You may stop

the whirlpool function at any time by pressing the button again.

3. The foot-spa is equipped with a hand held sprayer. To activate the hand shower, pull the hand shower

from the receptacle and depress the thumb control on the sprayer handle. This will turn on the water. When you

release pressure on the thumb control this will turn the water off.

4. To drain whirlpool tub:

The spa is equipped with a built in optional discharge pump. Open the drain plug

by turning the control knob with which is situated at the far right of the spa base. Press discharge pump timer button

situated far left on front of base (pump will run for approx. 2 min.) Average time for drain 1 minute.

5. 9600 & 9700 chairs Shiatsu Roller back massage is equipped with a state of-the-art massage system. The

massage system is easy to use; the remote has a one touch power that starts select your own massage. You can

also adjust the front to rear position of the chair and the reclining back. By using the remote your client can adjust the

back to the most comfortable position.

BASIC PRECAUTIONS SHOULD ALWAYS BE OBSERVED, INCLUDING THE FOLLOWING:

1. Read and follow all instructions

2. DANGER. To reduce the risk of injury, do not permit children to use this unit unless they are supervised at all

times

3. Use this unit only for its intended use as described in this manual. Do not use attachments that are not

Recommended by the manufacturer.

4. Never drop or insert any object into any opening.

5. Do not block jets during whirlpool operation.

6. The unit must be connected to an electrical supply circuit that is protected by a ground fault circuit interrupter.

7. The clean jet motor is magnetically driven and is insulated twice. Therefore it does not require to be bonded.

Save these instructions

OPERATIONS & USE

9700 Shiatsu Remote Control

Please refer to instruction manual for operations

LCD

Auto

Neck

Shoulder

Knocking

Speed

Upper

Adjustment

Recline

Seat

Backward

Timing

Power

Back Waist

Kneading

Air On/Off

Intensity

Pause

Kneading

Knocking

Width

Lower

Adjustment

Incline

Seat

Forward

10

OPERATIONS & USE

9500/9600 Shiatsu Remote Control

Please refer to instruction manual for operations

LCD

Power

Timing

TT960

Upper

Body

Knead Flap

Knead

Flap

Neck

Shoulder

Press Manual Knock

Back

Waist

Back

Stretching

Speed

Width

Seat

On/Off

Mode

Intensity

Seat

Forward

Seat

Backward

Seat

Incline

Seat

Recline

11

12

CLEANING & MAINTENANCE

Please refer the diagrams to remove jet covers for cleaning

Gulfstream Plastics Ltd. highly recommends the following cleaning regimen. You should always contact your local governing agency for their specific cleaning and disinfecting requirements and regulations for pedicure spas. For your clients safety, always use the regulations as a minimum standard for cleaning and disinfecting. Combining your states standards with the regimen listed below will provide your clients with a safe and healthy pedicure spa environment experience.

Routine maintenance:

Powdered cleansers or abrasives are NOT RECOMMENDED. A clean towel or sponge, are all that are usually needed. A soft bristled brush may be used when excessive residue is present. Use a mild soap and water solution to clean the upholstery, but do not over wet. Wipe dry with a clean towel. No internal maintenance of the spa components is necessary. Remove clean jet caps and spray with disinfectant after each use. For extra protection, our recommendation is that the system be flushed daily or weekly depending on use. To flush the clean jet system fill spa with hot water to just above the jets. Add disinfectant. Run whirlpool for 15 minutes, drain and then wipe dry with clean soft cloth.

NOTE:

Cleaning or sanitizing is NOT disinfecting. According to the Centers for Disease Control and Prevention (CDC), and the US Environmental Protection Agency (EPA), disinfecting occurs only when there is a reduction of pathogenic microbes at 99.999%. Sanitizing is only a reduction of 99.9%. Cleaning of whirlpool pedicure spas requires surfactant and chelating detergents that are low-foaming and have the ability to remove body oils, organic oil additives, mineral oil, skin cells, nail clippings etc that can accumulate both in the basin and the jets which may become a fertile area for micro organisms to grow.

The use of oil based products can build up in the whirlpool system causing clogging in the jets. Adherence to the above cleaning will minimize build up. Gulfstream Plastics Ltd does not recommend the use of mineral oil based products.

TESTING/FLUSHING FOOT SPA

After foot spa has been installed, fill tub with water just above the jets. Carefully check for leaks at drain and over flow. After checking underside for leaks turn on system by pushing whirlpool button and watch for leaks as water circulates. Let tub run full cycle. Open drain plug for water discharge.

13

WARRANTY & SERVICE

Gulfstream warrants to the original purchaser that the new pedicure spa will be free from defect during the Standard Warranty Period

(listed below). The shipping date and the uniquely-coded Serial Number on the back of each spa chair will justify the start of the warranty period for the product. The warranty is null and void if the pedicure spa is taken from its initial place of installation, or it is not installed in accordance with federal, state or local codes and ordinances. Also, this warranty does no apply if the pedicure spa has been subject to misapplication, improper installation or maintenance, negligence, improper cleaning or other circumstances beyond

Gulfstream's control.

Warranty

1. Limited Three(3) Years warranty on Spa Shell.

2. Limited One(1) Year warranty on the Whirlpool Pump.

3. Limited One(1) Year warranty on the Clean Jet.

4. Limited One(1) Year warranty on the Glass Bowl.

5. Limited One(1) Year Parts-Only warranty which covers the Hydraulic System, Discharge Pump, Massage System and All

Electrical Components.

6. Gulfstream will pay shipping charges on all replacement parts during the first 90 days of the stated Warranty Period. After 90

days the consumer is responsible for all labor and shipping costs incurred.

Exclusions

1. Damage to pump parts and/or motor parts due to obstruction in plumbing lines etc.

2. Staining, fading or discoloration of plastic surfaces due to exposure and/or the use of harmful cleaning agents or

Chemicals.

3. Staining, fading or discoloration caused by improper or poor water additives not related to the maintenance of

Proper water are not covered by this warranty.

4. Staining, fading or discoloration of the seat, armrests or footrests.

5. Freight damage, misuse, neglect, accident, natural disaster and abuse.

6. Unauthorized repairs.

Service

1. The Dealer shall forward all warranty-related matters to our Customer Service Department.

2. Serial Numbers and Original Invoice must accompany all warranty claims.

3. Customers are responsible for shipping defective parts back to Gulfstream. These parts must be packaged

correctly in order to protect against any further damage.

4. All parts are to be shipped by UPS Ground Service average 2-5 days.

5. All defective parts must be shipped back to Gulfstream within 30 days of receiving the new replacement parts or

warranty will be void.

6. Any warranty claim that cannot be determined over the phone, the customer must send photos and original

invoice directly to Gulfstream before any repairs can be performed.

7. Any service performed on the product without Gulfstreams authorization will also void the Warranty.

8. Each service call from the customer will be assigned a Claim Number. The Claim Number will stay open until the

problem is resolved.

No dealer or other person has any authority to bind Gulfstream Plastics Ltd. to changes or additions to this warranty or its products.

Accordingly, Gulfstream Plastics Ltd. is not responsible for such warranties or representations.