Eureka | Euroair Detox | Instruction manual | Eureka Euroair Detox Instruction manual

Instruction Manual
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
Thank you for selecting our Euroair Energie – Photocatalytic Air Purifier.
Please read the instruction manual carefully and keep it for future reference.
Important Safeguards
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
Warning: If the supply cord is damaged, it must be replaced by the
manufacturer, service agent or similar qualified person in order to avoid
a hazard.
To reduce the risk of electric shock:
l
Use indoors only
l
Plug in the right power source described on the label
l
Keep the air purifier out of reach of children or invalids to prevent from
injury
l
Use of an extension cord is not recommended as it may cause a short
circuit or destroy the unit or may cause personal injury
l
Turn off all controls before unplugging. Always disconnect cord from
electrical outlet before servicing the air purifier
l
Do not unplug by pulling on cord. To unplug, grasp the plug, not the
cord
l
Never handle plug or air purifier with wet hands
l
Do not pull or carry by cord, use cord as a handle, close door on cord or
pull cord around sharp edges or corners. Keep cord away from heated
surfaces
l
Do not use with damaged cord or plug
l
Do not operate the air purifier near a shower, bathtub or in the place
where steam may be present. It may cause a short circuit or influence
the performance of cleaning
l
Do not immerse the air purifier in water or any other liquid. This should
destroy the unit
l
Do not operate the air purifier near a stove or heater
l
Do not operate the air purifier where flammable gases such as oxygen,
natural gas or propane may be present
l
Do not put any object into the cover openings
Save these instructions!
1
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
Air Purifier Description
Main Structure
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
Front view
Front cover
Pre-filter
Compound Filter (HEPA+Activated Carbon)
UV Tubes (×2)
Nano-photocatalytic Filter
Fan
Side Air Flow Inlet
Power Control
Air Flow Outlet
Function Buttons
Display
Remote Control Signal Receiver
Dust Sensor
Front Panel
Gas Sensor
Front Air Flow Inlet
2
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
Purifying Process and Main Features
l
Pre-filter
It filtrates larger particles to prolong the lifespan of the HEPA filter.
l
Compound Filter
It consists of two layers of filters, one is the true HEPA Filter and the other is the
Activated Carbon Filter. The former filtrates particulates as small as 0.3 micron,
like pollen, smoke, pet dander, mould, airborne dust, etc. The latter is designed to
treat odours.
l
UV Tubes
Their UVC germicidal irradiation can destroy airborne bacteria and viruses.
l
Nano-photocatalytic
Filter:
This filter decomposes thoroughly, the toxic gases and viruses from the air 300
times more effectively than standard carbon filters. It also has t h e a b i l i t y t o
regenerate and clean itself with minimal attention.
l
Anion
Generator
This feature aims to generate a great deal of negative ions to keep the air fresh
always.
l
Dust Sensor
& Gas Sensor
They detect air quality and show air quality level on display. In Auto Mode, the
unit automatically adjusts its fan speed accordingly, to deal with the
contaminant quickly.
l
Mounting
your Air Purifier
In order to get greater efficiency in cleaning, it is recommended to place the
purifier on the ground or on a holder about 50cm high and at convectionposition
against the air conditioner or other similar appliances.
3
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
Function Description
l
Standby
Under Standby Mode, no letters or icons will be shown on the display.
The Standby Indicator illuminates in red to show the apparatus has been
connected with power.
l
Purify Air
UV Tubes work with the Nano-photocatalytic Filter in this mode.
l
Refresh
Anions are generated under this mode.
l
Fan Speed
There are five different fan speeds. Turbo is the highest speed while Silent - the
lowest makes the unit work in whispering silence.
l
Air quality
indicator
There are four levels of air quality as indicated below:
Very good
Good
Ordinary
Poor
l
Auto
This mode automatically determines the working condition according to the air
quality detected by the Dust Sensor and Gas Sensor. Ion generator and UV
Tubes work together in this mode. Below is the relative fan speed for each level
of air quality.
Very good
Silent
Good
Middle
Ordinary
Poor
Strong
Turbo
l
Check
Filter
When the purifier has worked for 3000 hours cumulative, the maintenance
indicator illuminates to remind the user to change the Pre-filter and Activated
Carbon Filter. Meanwhile check the HEPA Filter with the colour shade on the
frame to see whether it is necessary to replace it.
4
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
After maintenance, press 'Fan Speed' and 'Refresh' buttons
simultaneously for 3 seconds to reset the counter. Please note that
whenever the 'Fan Speed' and 'Refresh' buttons are pressed
simultaneously, the counter will be reset.
If you do not reset the counter after checking the filter, or forget to
check the filter after 3000 hours, 'Check Filter' will blink after 3500 hours to
remind the you again.
l
UV Status
Indicator
When 'UV1' or 'UV2' icons illuminate, it means the relative UV tube is not
working and needs replacing.
How to Use
Buttons and Display
l
Buttons
ON / OFF, Speed, Timer, Purify Air, Refresh
l
LED Display
Remote Control
l
Buttons
Description
1. ON/OFF: Turns on or turns off the apparatus
2. Fan Speed: Adjusts the fan speed
3. Refresh: Starts or stops the working of the Ion Generator
4. Timer: Sets Automatic Off Time at 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10 / 11 / 12 hours
5. Auto: Starts or calls off the Auto Mode
6. Purify Air: Shifts to Photocatalytic Purification
l
Batteries
Assembly
1. Press the Interlock and remove the battery cabinet cover.
2. Correctly put in batteries according to the '+', '-' icons inside.
5
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
Operation Guide
l
ON/OFF
Connected with power, the unit beeps with all the display icons illuminating
together and enters Standby Mode after 1 second.
Press the ON / OFF button, the unit starts running at Strong speed. 'Refresh'
and 'Purify Air', do not function together until 3 minutes later when the unit shifts
to Auto Mode, under which the Ionizer and UV tubes work together.
Any time the unit gets restarted, it remembers its last working status.
l
Fan Speed
It controls Fan Speed and Auto Function.
Based on the initial Strong speed, the Fan Speed Cycles in the following order:
Strong ---Turbo --- Auto (according to air quality) ---Silent --- Middle
There are indicators in different colours for each Fan Speed. For Silent, it’s
green. For Middle it's blue. For Strong it's orange and for Turbo it's red.
l
Refresh
Press this button and the Ionizer starts generating Anions. Press this button
again and the Ionizer stops working.
l
Timer
Each press of this button increases 1 hour to the counter until it accumulates to
12 hours, after which point the counter will be called off. When this button is
kept pressed down, the programmed time increases rapidly.
l
Purify
Air
It controls photocatalytic purification.
Maintenance
Cover and Housing
l
Do remember to cut off the power supply before maintenance
l
Clean the unit only when necessary. If the unit is used in a dirty
environment, it
may need more frequent cleaning
l
Wipe the dirt with soft fibres
l
For obstinate dirt, only a neutral detergent is recommended
Caution: Never expose (the Housing) to hard and speculate objects to avoid
nicks. Carefully remove the front cover or the parts may get damaged.
Sensors
l
Clean out the dust blocking the sensors’ air inlet
l
Clean out the dust in an aperture or a limited space with the vacuum cleaner
l
Wipe the sensors’ lens with a cotton bar. Do remember never wipe the lens with
organic solvent for the lens is coated with protective membrane
6
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
Filters
The Filters should be cleaned or replaced regularly.
Pre-filter: It is as washable as normal fabric but DO NOT wring it. Let it dry flat. It
is recommended to wash this filter every 3 months and replace it after 1 year.
Compound Filter: It is recommended to clean the dust gathered on this filter with a
vacuum cleaner every 3 months. It needs to be replaced when the purification
efficiency is greatly reduced. Generally speaking, its lifespan is 1-12 years.
l
Disassembly
1. Front cover: Press the cover inwards at the top two corners to loosen the
interlock switch. Then, pull the whole cover upwards to take it off.
2. Pre-filter: Turn the locks in the arrows’ direction to release the Pre-filter.
3. Compound Filter: Hold the small ribbon and pull the filter out.
4. UV Tubes: Turn the lamp clockwise or anti-clockwise until the Tube is parallel to
the Aclinic openings. Take the Tube out from the tube-holder levelly.
1
2
3
4
l
Assembly
1. UV Tubes: Place the Tube into the tube-holder from the aclinic openings. Turn
the lamp clockwise or anti-clockwise to secure it.
2. Compound Filter: Put the filter in place from the bottom and then push it into the
cabinet. HEPA Filter should face outside.
3. Pre-filter: Place in the Pre-filter and turn the locks in the arrows’ direction to
secure it.
4. Front Cover: Secure the interlock at the bottom first and push the whole cover
inwards at the two top corners to secure it.
1
2
3
Please contact to the distributor or agent for purchasing filters.
7
4
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
Technical Specification
Rated Power
120 W
Input Voltage
220-240 V 50 / 60 Hz
Ionizer
> 3.0 million / cc
Max. Airflow
500 m3 / hour
Product Weight
8.5 kg
Dimensions (W x D x H in mm)
441 x 209 x 559
Advanced Features
HEPA FILTER - It removes dust up to 0.3 micron, smoke, harmful gases
and odour from the air with its powerful 7 - stage purification. It is very
effective and can trap RSPM and protect you from 99.97% air borne
particles.
LOW NOISE - It works at lower noise levels than other air purifiers, so
you can have a good night's sleep. In offices, it won't intrude on the work
environment.
5-SPEED - With the convenient 5-speed control - Turbo, Strong, Middle,
Silent, Auto – you can switch speeds depending on your room space and
pollution to ensure optimum freshness.
UV LAMP / HEPA REPLACEMENT INDICATOR - Keep your mind worryfree as it indicates when the UV lamp needs to be replaced.
TIMER - Automatic On / Off for 1 - 12 hours gives you the flexibility to
programme your Euroair Energie as per your requirements.
UV LAMPS - Double UV lamps for extra protection.
DUST, SMOKE AND GAS SENSORS - They detect the air quality and show
the air quality level on the display.In Auto Mode,the unit automatically
adjusts its fan speed accordingly,
to deal with the contaminant quickly.
8
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
LED DISPLAY - It displays information about air purity levels,dust levels,
usage hours,speed controls,etc.to help keep your Euroair Energie
functioning effectively always.
CONTROL - It comes with an easy-to-use Remote Control.
SAFETY - It cares for your safety enabling Automatic Power-Off when the
front cover is opened.
ANTI POLLEN - It filters out microscopic pollen particles that cause
severe allergies to ensure the air you breathe is safe.
NANO-PHOTOCATALYTIC FILTER - It decomposes toxic gases and
viruses from the air 300
times more effectively than standard carbon filters.
It
can regenerate and cleans itself with minimal attention.
-tive
-tive
-tive
-tive
-tive
-tive
-tive
-tive
ANION GENERATOR - It generates negative ions in large quantity to keep
the air fresh at all times,
so you feel energised always.
-tive
hours,
the
CHECK FILTER - When the purifier has worked for a total of 3000
maintenance indicator illuminates to remind you to change the Prefilter and
Activated Carbon filter,
and also check the HEPA Filter.
AIR-QUALITY INDICATOR - It indicates four levels of air quality - Very Good,
Good,
Ordinary,
Poor, for your convenience.
VARIABLE MOUNTING AND COVERAGE - Can be used as a table top, wall
mounted or as a self-standing model according to your convenience, providing
you an extensive coverage area of 1000 sq.ft.
9
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
Troubleshooting
Problem
Causes
Solution
The unit does not
work.
1. It is not firmly plugged
into the electrical
outlet.
2. Front cover is not
secure.
3. Remote control
batteries have run out.
1. Firmly plug it into the
electrical outlet.
2. Secure front cover.
3. Replace batteries.
No air blows out
Some object is blocking
the air inlet or air outlet.
Remove the object and
contact the distributor or
agent.
Expected cleaning
effect is not achieved.
1. The unit is placed in a
poorly-ventilated
environment or
blocked by other
objects.
2. Filters have gathered
too much dust and
smoke.
1. Remove the block.
2. Clean or change the
replaceable filters.
Air outlet smells
unpleasantly.
1. Too much odour is
generated together for
instance too many
people smoking.
2. Filters have absorbed
too much odour and
smoke.
1. Operate the apparatus
for a certain period.
2. Clean or change the
replaceable filters.
Air quality indicator
always shows poor air
quality all the time.
Lens inside the Sensors
is dirty.
Wipe the lens with a
cotton swab.
Caution: In the above-mentioned solutions do not work, please contact the
distributor or agent. Never arbitrarily disassemble, repair or restructure the apparatus
on your own.
10
EN
FEEL THE ENERGY.
FEEL THE FRESHNESS.
Download PDF

advertising