Yale Smart Living Keyless Fitting Instructions

Yale Smart Living Keyless Fitting Instructions
smart
Living
20mm Hole
Keyless Connected Smart
Lock Installation Guide
Keyless Connected
Contents Include
Installation Guide
Fit Yale digital lock using hand Philips screw driver to avoid cross threading fixing screws.
If using a cordless, please ensure it is set to low speed & torque.
• Screws
• Batteries
• Self adhesive
pad
Front Body
Battery Pack
Handing Plate
Please read the intructions before fitting and using the
Keyless Connected lock.
The functions and design of this product can be changed
without prior notice for performance and quality improvements.
Y3 Chrome
Nightlatch
Box(Option)
PLEASE READ THE INSTRUCTION BEFORE USING YALE KEYLESS CONNECTED LOCK.
The functions and design of this product can be changed
without prior notice for performance and quality improvement.
The smarter way to protect your home•
ISL-1290-01
Disassemble Lockset
Before getting started
Did you purchase the Yale Digital Lock including a Y3 Nightlatch?
Please disassemble your existing Nightlatch case and
mounting plate.
YES , I have bought the complete package to install them onto my door.
➞ Please start from installation step
ON THE RIGHT PAGE
* The nightlatch & plates above are generic images.
If you are retrofitting Yale digital lock,
your product may be different.
NO , I am going to keep using the existing Nightlatch on my door with the Yale digital product.
➞ There are many types of Nightlatches, so please start from installation step
BELOW, and
follow the check points for correct installation.
Check Point!!!
Please use the key of your existing Nightlatch and check the below
Ⓒ 90° deg
in either
direction
Ⓓ 90° deg in
either
direction
Ⓐ Keep your door open
Ⓑ Insert the key in the outside cylinder key hole
Ⓒ Turn the key 90° in either direction counter clockwise(to the left) and
check the latch fully retracts
Ⓓ Turn the key 90° in either direction clockwise(to the right) and check the latch fully retracts
Ⓑ KEY
Door Preparation
Use template
provided
Can you open with your key in both directions? Please go to step
Can you open with your key only in the
left direction? Not in the right direction?
Can you open with your key only in the
right direction? Not in the left direction?
➞ Your Nightlatch needs an additional plate.
➞ Your Nightlatch needs an additional plate.
PLEA SE G O TO STEP
PLEA SE G O TO STEP
Please attach the additional handing plate tightly onto the
cylinder fixing surface.
The plate must be alighed with the shape.
Make sure the 'LEFT TURN' is shown as the image below
if your latch is opened only to the LEFT direction by the key.
Self adhesive pad
20mm Hole
72.5mm
Please attach the additional handing plate tightly onto the
cylinder fixing surface.
The plate must be alighed with the shape.
Make sure the 'RIGHT TURN' is shown as the image below
if your latch is opened only to the RIGHT direction by the key.
Self adhesive pad
60mm
32mm Hole
Door Template
Cut Connecting Bar
Inside
ø20mm
Outside
*
18mm
Cut with pliers to ensure a clean cut.
Place the electronic keypad in the hole on the outside of the door.
Measure the connecting bar with the provided template, then mark at 18mm and cut. If
neccessary, use a hacksaw to shorten the flat connecting bar so it projects 18mm beyond the
surface of the door.
* If you are retrofitting with your existing Nightlatch, please place your existing cylinder onto the
door side and mark and cut the connecting bar at the same length with your cylinder.
(Please refer to the ‘*’ marked image above)
ø32mm
Warning: The projection of the connecting bar is important to ensure the lock works correctly.
If you are fitting with Y3 Nightlatch, it should not be shorter than 18mm.
If you are retroffiting, please make sure you do not cut the tail bar shorter than the existing tail bar.
Mount External Keypad and Mounting Plate
Use the template provided to
choose correct screw length
according to your door thickness.
Fix with the cylinder retaining screws first that you chose.
Make sure the front keypad is aligned before fixing the
screws tightly. Now fix the mounting plate onto the door.
Secure Lock Case
Door Thickness
Fit first
Staple Fitting
Secure Battery Pack
Feed the cable through the slot and then, being careful
not to overlap it, zig-zag any excess cable
behind the battery pack.
Connect the cable
to the battery pack
Insert Batteries and Close the Cover
①
Make sure battery back
is square with the door
Screw into boss
Fix screw to completely
secure battery pack.
Check Points after Installation
Place Lock Case and Chisel
* If you have used a handing plate on STEP 1-(L) or 1-(R),
please turn the follower to the end position according to
your direction before fixing the lock case.
Ⓐ Make sure to leave the door open when registering your PIN because you may accidentally lock
the door while trying to register or change your PIN code.
Ⓑ Touch the keypad with your palm to wake up the keypad.
Ⓒ Enter a PIN code 123456 and enter * button or touch the keypad with your palm to open the door.
*
Ⓓ Turn the knob handle several times to retract the latch bolt.
Ⓔ The knob handle will not retract the latch bolt after few seconds.
PLEASE NOTE: Remember to change your master code after installation.
Chisel required
if you have difficulty locating the bar into the slot in
the lock case, enter the master code 123456
followed by * to unlock the lock, this will engage the
bar and make it easier to locate.
To avoid any possibility of being locked out, do not close the door
until a PIN code has been successfully registered to allow access back in.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement