Audi | A4 - GUIDE 2008 | Owner`s manual | Audi A4 - GUIDE 2008 Owner`s manual

uli 2007 9:16 09
Audi A4
Audi A4
englisch 9.07
Owner's Manual
uli 2007 9:16 09
© 2007 AUDI AG
AUDI AG works continuously to develop and further improve all
models. You will appreciate that we must therefore reserve the right
to alter any part of the vehicle and its equipment or technical specifications at any time. No legal commitment can therefore be
implied by the information, illustrations or descriptions in this
Manual.
No part of this Owner's M
translated without the wr
under the laws of copyrig
Subject to alteration and
Date of publication: 27.06
For the sake of th
This paper was bleached
document_0900452a81b1b9de.book Seite 1 Donnerstag, 26. Juli 2007 9:16 09
Foreword
Thank you for choosing the Audi A4.
The new Audi A4 combines the latest technology with numerous features for your comfort and
convenience. To help you get the best out of these features in everyday use, we recommend that
you read this Manual carefully so you can quickly become familiar with your vehicle in detail.
As well as information on how to use the controls and equipment, the Owner's Manual contains
important notes on care and maintenance. These are relevant to your safety and will help preserve
your car's value. The Manual also offers useful driving tips and advice, together with some suggestions on how to drive your car with minimum impact on the environment.
In addition to this Owner's Manual, the Service Wallet also includes the Service Schedule for your
vehicle. This booklet contains important information on Audi service requirements and lists the
vehicle's fuel consumption figures. The Service Wallet also includes operating manuals for
optional on-board systems such as the radio, navigation and telephone. We recommend that you
keep the Service Wallet in the car at all times.
Should you have any further questions regarding your car or if you suspect that your owner's literature is not complete, please contact your Audi dealer or importer. They are always glad to answer
your queries and note any suggestions you may have.
We wish you safe and enjoyable motoring with your Audi A4.
AUDI AG
document_0900452a81b1b9de.book Seite 2 Donnerstag, 26. Juli 2007 9:16 09
2
Contents
Contents
Notes on this Owner's
Manual . . . . . . . . . . . . . . . . . . . . . .
Controls
5
.....................
7
Controls and displays . . . . . . . . . .
9
9
Overview
......................
Instruments and
warning/indicator lamps . . . . . . .
Instruments . . . . . . . . . . . . . . . . . . . .
Fuel gauge . . . . . . . . . . . . . . . . . . . . .
Warning and indicator lamps . . . . .
Driver information system . . . . . .
Introduction . . . . . . . . . . . . . . . . . . .
On-board computer . . . . . . . . . . . .
Speed warning function . . . . . . . .
Auto-check control . . . . . . . . . . . . .
Tyre pressure monitoring system
.
.
.
.
.
Doors and windows . . . . . . . . . . . .
Central locking system
Boot lid . . . . . . . . . . . . .
Child-proof catches . .
Electric windows . . . .
Sun roof . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Lights and vision . . . . . . . . . . . . . . .
Lights . . . . . . . . . . . . . . . . . . . . . . . . .
Interior lights . . . . . . . . . . . . . . . . . . .
11
11
14
15
21
21
25
28
30
39
42
42
51
53
53
55
57
57
63
Clear vision . . . . . . .
Windscreen wipers
Rear-view mirrors .
Digital compass . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
64
65
68
71
Seats and storage . . . . . . . . . . . . .
73
73
74
75
77
78
79
83
84
85
86
Manual adjustment of front seats
Electric adjustment of front seats
Seat memory . . . . . . . . . . . . . . . . . .
Head restraints . . . . . . . . . . . . . . . .
Front armrest . . . . . . . . . . . . . . . . . .
Luggage compartment . . . . . . . . .
Roof carrier . . . . . . . . . . . . . . . . . . . .
Roof load . . . . . . . . . . . . . . . . . . . . .
Cup holders . . . . . . . . . . . . . . . . . . .
Ashtrays . . . . . . . . . . . . . . . . . . . . . .
Cigarette lighter and electrical
sockets . . . . . . . . . . . . . . . . . . . . . . .
On-board 230 Volt Euro socket . . .
Storage compartments . . . . . . . . .
Heating and cooling . . . . . . . . . . .
Deluxe automatic air conditioner .
Deluxe automatic air conditioner basic settings . . . . . . . . . . . . . . . . . .
Deluxe automatic air conditioner
plus . . . . . . . . . . . . . . . . . . . . . . . . . .
Deluxe automatic air conditioner
plus - basic settings . . . . . . . . . . . .
Auxiliary heating and auxiliary
ventilation . . . . . . . . . . . . . . . . . . . . .
Seat heating . . . . . . . . . . . . . . . . . . .
Driving . . . . . . . . . . . . . . . . . . . . . . . . .
Steering . . . . . . . . . . . . . . . . . . . . . . .
Ignition lock . . . . . . . . . . . . . . . . . . .
Starting and stopping the engine
with the advanced key . . . . . . . . . .
87
89
90
93
93
100
101
109
110
114
116
116
116
118
Electro-mechanical parking brake
Cruise control system . . . . . . . . . . .
121
125
adaptive cruise control (ACC) . .
128
128
134
140
142
Speed and distance control system
Driver messages . . . . . . . . . . . . . . .
System limitations . . . . . . . . . . . . . .
Audi braking guard . . . . . . . . . . . . .
Audi lane assist . . . . . . . . . . . . . . . .
Audi lane assist . . . . . . . . . . . . . . . .
Audi side assist . . . . . . . . . . . . . . . .
Lane change assist feature . . . . . .
Notes . . . . . . . . . . . . . . . . . . . . . . . . .
Audi drive select . . . . . . . . . . . . . . .
145
145
149
149
156
.....
159
159
Automatic gearbox . . . . . . . . . . . . .
162
multitronic®, tiptronic (6-speed
gearbox) . . . . . . . . . . . . . . . . . . . . . . .
162
Adjusting the vehicle set-up
Parking aid . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
169
169
169
170
171
...
...
...
177
177
178
HomeLink . . . . . . . . . . . . . . . . . . . . . .
179
179
General notes . . . . . . . . . . . . . . .
Audi parking system . . . . . . . . .
Audi parking system plus . . . . .
Audi parking system advanced
Switching display and acoustic
signals on and off . . . . . . . . . . .
Towing bracket . . . . . . . . . . . . . .
Error messages . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
Universal transmitter . . . . . . . . . . . .
document_0900452a81b1b9de.book Seite 3 Donnerstag, 26. Juli 2007 9:16 09
Contents
Safety
.......................
185
Driving tips
................
221
General maintenance
Safe driving . . . . . . . . . . . . . . . . . . . .
186
186
188
191
192
Intelligent technology . . . . . . . . . .
222
Care of vehicle and cleaning . . . 244
.
.
.
.
Seat belts . . . . . . . . . . . . . . . . . . . . . .
194
Why is it so important to use seat
belts? . . . . . . . . . . . . . . . . . . . . . . . . .
Forces acting in a collision . . . . . .
How to wear seat belts properly .
Belt tensioners . . . . . . . . . . . . . . . . .
Electronic stabilisation program
(ESP) . . . . . . . . . . . . . . . . . . . . . . . .
Brakes . . . . . . . . . . . . . . . . . . . . . . .
Power steering (servotronic) . . .
Four-wheel drive (quattro®) . . . .
Power management . . . . . . . . . .
222
224
225
226
226
194
195
197
199
General notes . . . . . . . . . . . . .
Correct sitting positions . . .
Pedal area . . . . . . . . . . . . . . . .
Stowing luggage safely . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Airbag system . . . . . . . . . . . . . . . . .
Description of airbag system . . . .
Front airbags . . . . . . . . . . . . . . . . . .
Side airbags . . . . . . . . . . . . . . . . . . .
Head-protection airbags
(sideguard) . . . . . . . . . . . . . . . . . . . .
Deactivating the front passenger's
airbag via the key-operated switch
201
201
203
205
207
210
Points to remember if children are
travelling in the car . . . . . . . . . . . . .
Child safety seats . . . . . . . . . . . . . .
Fitting child safety seats . . . . . . . .
210
213
216
Safety
.
.
.
.
.
Your vehicle and the
environment . . . . . . . . . . . . . . . . . . .
...
...
229
229
229
...
...
229
231
Towing a trailer . . . . . . . . . . . . . . . .
232
Driving the vehicle with a trailer or
caravan . . . . . . . . . . . . . . . . . . . . . . .
Removable towing bracket . . . . . .
232
235
Running in . . . . . . . . . . . . . . . . . .
Emission control systems . . . .
How to improve economy and
minimise pollution . . . . . . . . . . .
Environmental compatibility . .
General notes . . . . . . . . . . . . . . . . . .
Care of exterior . . . . . . . . . . . . . . . . .
Care of interior . . . . . . . . . . . . . . . . .
243
244
244
247
Fuel and filling the tank . . . . . . . . 251
Petrol . . . . . . . . . . . . . . . . . . . . . . . . . .
Diesel . . . . . . . . . . . . . . . . . . . . . . . . .
Filling the tank . . . . . . . . . . . . . . . . . .
Checking and topping up fluids
Bonnet . . . . . . . . . . . . . . . . . .
Engine compartment layout
Engine oil . . . . . . . . . . . . . . . .
Cooling system . . . . . . . . . . .
Brake fluid . . . . . . . . . . . . . . .
Battery . . . . . . . . . . . . . . . . . .
Windscreen washer . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
251
251
252
254
254
256
257
260
262
263
267
Wheels and tyres . . . . . . . . . . . . . . . 268
Wheels . . . . . . . . . . . . . . . . . . . . . . . .
Run flat tyres . . . . . . . . . . . . . . . . . . .
208
Child safety . . . . . . . . . . . . . . . . . . . .
Controls
.
.
.
.
.
...
3
268
274
Accessories and modifications
to the vehicle . . . . . . . . . . . . . . . . . . . 277
Accessories and replacement
parts . . . . . . . . . . . . . . . . . . . . . . . . . .
Modifications . . . . . . . . . . . . . . . . . .
Radio transmitters and business
equipment . . . . . . . . . . . . . . . . . . . . .
Driving tips
General maintenance
Self-help
277
277
278
Technical data
document_0900452a81b1b9de.book Seite 4 Donnerstag, 26. Juli 2007 9:16 09
4
Contents
Self-help
.....................
281
Self-help . . . . . . . . . . . . . . . . . . . . . . . . 282
Warning triangle . . . . . . . . . . . . . . .
First-aid kit . . . . . . . . . . . . . . . . . . . .
Fire extinguisher . . . . . . . . . . . . . . .
Tools and Tyre Mobility System . .
Compact temporary spare wheel*
Tyre repairs . . . . . . . . . . . . . . . . . . .
Changing a wheel . . . . . . . . . . . . .
Jump-starting . . . . . . . . . . . . . . . . .
Tow-starting and towing away . .
.
.
.
.
.
.
.
.
282
282
283
283
284
285
288
293
295
Technical data
............
319
General notes . . . . . . . . . . . . . . . . . .
320
320
320
321
321
Explanation of technical data
Dimensions . . . . . . . . . . . . . . . .
Capacities . . . . . . . . . . . . . . . . .
Vehicle identification data . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Performance, weights and
dimensions . . . . . . . . . . . . . . . . . . . .
Petrol engines . . . . . . . . . . . . . . . . .
Diesel engines . . . . . . . . . . . . . . . . .
323
323
325
Fuses and bulbs . . . . . . . . . . . . . . . . 300
Fuses . . . . . . . . . . . . . . . . . . . . . . . . .
Bulbs . . . . . . . . . . . . . . . . . . . . . . . . .
Changing bulbs for headlights . .
Changing bulb for front fog lights
Changing bulbs for rear lights in
side panel . . . . . . . . . . . . . . . . . . . . .
Changing bulbs in boot lid . . . . . .
Number plate light . . . . . . . . . . . . .
.
.
.
300
304
306
310
.
.
.
311
314
315
Index
........................
329
document_0900452a81b1b9de.book Seite 5 Donnerstag, 26. Juli 2007 9:16 09
Notes on this Owner's Manual
5
Notes on this Owner's Manual
This Owner's Manual contains important information, tips, suggestions and warnings.
Please ensure that this Owner's Manual is always kept in the vehicle.
It should always be available to anyone else driving the vehicle, i.e.
anyone renting, borrowing or buying the vehicle from you.
This manual describes the equipment available for the vehicle at the
time of going to print. Some of the equipment described here will
not be available until a later date, or may only be available in certain
markets.
Some sections of this Owner's Manual do not apply to all vehicles.
If this is the case, a text at the start of the section indicates which
vehicles it applies to, e.g. “Applies to vehicles: with auxiliary heater”.
This optional equipment is also marked with an asterisk “*”.
Illustrations are intended as a general guide, and may vary from the
equipment fitted in your vehicle in some details.
At the beginning of this Owner's Manual, you will find a table of
contents showing all the items described in this manual in the order
in which they appear. An alphabetical index is included at the end
of the Owner's Manual.
WARNING
Texts with this symbol contain safety information. They warn you
of serious dangers, possibly involving accident or injury.
Caution
Texts with this symbol draw your attention to a possible risk of
damage to your vehicle.
For the sake of the environment
Texts with this symbol refer to points relevant to the protection of
the environment.
Note
Texts with this symbol contain additional information of a more
general nature.
All references to positions such as “left”, “right”, “front” or “rear”
are given as seen facing in the direction of travel.
*
optional equipment
 The section is continued on the following page.
 Denotes the end of a section.
®
Registered trademarks are marked ®. However, the absence of
this symbol does not constitute a waiver of the rights
concerning any proprietary name.
⇒
Refers to a “WARNING” within the same section. If the
WARNING symbol is followed by a page number the warning text
referred to is included in a different section.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 6 Donnerstag, 26. Juli 2007 9:16 09
6
document_0900452a81b1b9de.book Seite 7 Donnerstag, 26. Juli 2007 9:16 09
Controls
7
document_0900452a81b1b9de.book Seite 8 Donnerstag, 26. Juli 2007 9:16 09
8
Controls and displays
Fig. 1 Some of the items of equipment listed in this section are only fitted on certain models or are optional extras.
document_0900452a81b1b9de.book Seite 9 Donnerstag, 26. Juli 2007 9:16 09
Controls and displays
9
Controls and displays
− Radio
Overview
1
A
2
A
3
A
4
A
5
A
6
A
7
A
8
A
9
A
10
A
− CD changer
Door handle
Seat memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric adjuster for exterior mirrors . . . . . . . . . . . . . . .
Central locking switch . . . . . . . . . . . . . . . . . . . . . . . . . . .
Button for side assist . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control lever for:
− Turn signals and main beam headlights . . . . . . . . .
18 Depending on equipment fitted:
A
75
70
49
149
57
59
− Radio display
− MMI display 1)
Hazard warning lights
Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front passenger's airbag . . . . . . . . . . . . . . . . . . . . . . . . .
Switches for the following (as applicable):
− Audi parking system . . . . . . . . . . . . . . . . . . . . . . . . . .
90
203
62
− Electronic Stabilisation Program (ESP) . . . . . . . . . . .
222
− lane assist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headlight range control . . . . . . . . . . . . . . . . . . . . . . . . .
Steering wheel with:
− Horn
145
61
− Electric sun blind . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
− Control for Audi drive select . . . . . . . . . . . . . . . . . . . .
Air conditioner, depending on equipment fitted:
− Deluxe automatic air conditioner . . . . . . . . . . . . . . . .
159
− Driver's airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
203
− Deluxe automatic air conditioner plus . . . . . . . . . . .
Ashtray with cigarette lighter . . . . . . . . . . . . . . . . . . . . .
Depending on gearbox fitted, gear lever or selector
lever for:
− multitronic® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
101
86, 87
A
20
A
21
A
22
A
19
23
A
− Controls for audio, TV*, telephone and speech
dialogue system*
24
A
25
A
170
93
11
A
12
A
13
A
14
A
− Paddle levers for tiptronic gearshift . . . . . . . . . . . . .
SET button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument cluster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset button for trip recorder . . . . . . . . . . . . . . . . . . . .
Control lever for:
− Windscreen wipers and washer . . . . . . . . . . . . . . . . .
167
12
11
14
65
− Switch for Audi parking system . . . . . . . . . . . . . . . . .
170
15
A
16
A
− On-board computer . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air outlets with thumbwheel . . . . . . . . . . . . . . . . . . . . .
− For deluxe automatic air conditioner . . . . . . . . . . . .
25
116
107
99
− Switch for Electronic Stabilisation Program (ESP
OFF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
222
− For deluxe automatic air conditioner plus . . . . . . . .
Depending on equipment fitted:
107
17
A
Controls
Safety
Driving tips
26
A
1)
162
− Manual gearbox
Depending on equipment fitted:
− MMI control console or
Depending on the equipment fitted in your vehicle the display screen is either two-coloured or multi-coloured. As the two displays are more or less
identical this Owner's Manual uses the multi-coloured displays for illustration purposes.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 10 Donnerstag, 26. Juli 2007 9:16 09
10
Controls and displays
− Switch for electric sun blind . . . . . . . . . . . . . . . . . . .
27
A
28
A
29
A
30
A
31
A
32
A
33
A
•
− Control for Audi drive select . . . . . . . . . . . . . . . . . . .
Start/stop button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electro-mechanical parking brake . . . . . . . . . . . . . . . .
Adjustable steering column (hidden behind steering
wheel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Depending on equipment fitted:
− Cruise control system . . . . . . . . . . . . . . . . . . . . . . . .
− adaptive cruise control
Bonnet lock release . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch for releasing the boot lid . . . . . . . . . . . . . . . . . .
Electric windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
159
118
121
116
125
254
51
53
Note
Please refer to the separate operating manual for instructions on
using the Multi Media Interface (MMI).
•
The arrangement of switches and controls on right-hand drive
models* may be slightly different from the layout shown in the illustration ⇒ page 8, fig. 1. However, the symbols used to identify the
controls are the same.
document_0900452a81b1b9de.book Seite 11 Donnerstag, 26. Juli 2007 9:16 09
Instruments and warning/indicator lamps
11
Instruments and warning/indicator lamps
7 Speedometer
A
8 Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A
Instruments
14
Instrument cluster overview
The instrument cluster is the driver's information centre.
•
Note
The needles in the instrument cluster will sweep across the dials
when you switch on the ignition.
•
The instrument lighting (illumination of dials and needles) is
switched on when the ignition is on and the vehicle's lights are off.
The instrument lighting is dimmed automatically as the daylight
starts to fade. This function is intended to remind the driver to
switch on the dipped-beam headlights in good time when light
conditions become poor.
Coolant temperature gauge
1 ⇒ fig. 2 only works when the
The coolant temperature gauge A
ignition is switched on. In order to avoid possible damage to the
engine, please read the following notes for the different temperature ranges.
Engine cold
Fig. 2 Overview of instrument cluster
1
A
2
A
3
A
4
A
5
A
6
A
Coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . .
Rev counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning and indicator lamps . . . . . . . . . . . . . . . . . . . . .
SET button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display
− Driver information system . . . . . . . . . . . . . . . . . . . . .
11
12
15
12
− Date and time display . . . . . . . . . . . . . . . . . . . . . . . . .
13
− Mileage recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset button for trip recorder . . . . . . . . . . . . . . . . . . . .
14
14
Controls
Safety
21
Driving tips
If the needle is still in the lower range of the dial, this indicates that
the engine has not yet reached operating temperature. Avoid high
engine speeds, full acceleration and heavy engine loads.
Normal temperature
In normal operation the needle will settle somewhere in the centre
of the dial once the engine has reached operating temperature. The
needle may also go further up when the engine is working hard at
high outside temperatures. This is no cause for concern provided
the warning symbol  in the display does not start flashing.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 12 Donnerstag, 26. Juli 2007 9:16 09
12
Instruments and warning/indicator lamps
Warning symbol in instrument cluster

If the symbol  lights up in the display, this means that either the
coolant temperature is too high or the coolant level is too low
⇒ page 33.
If the needle is at the top end of the dial, this means the coolant
temperature is too high. Stop the vehicle, switch off the engine and
wait for it to cool down. If the warning lamp starts flashing again
after just a short distance, contact a qualified workshop.
WARNING
•
Before opening the bonnet and checking the coolant level,
please observe the warning information on ⇒ page 255, “Working
on components in the engine compartment”.
•
Never open the bonnet if you can see or hear steam or coolant
escaping from the engine compartment; there is a risk of being
scalded. Wait until you can no longer see or hear escaping steam
or coolant.
Rev counter
The rev counter indicates the number of engine revolutions per minute.
You should select a lower gear if the engine speed drops below
1500 rpm. The start of the red zone on the dial indicates the
maximum engine speed which may be used briefly when the engine
is warm and after it has been run in properly. However, it is advisable
to change up a gear or move the selector lever to “D” (or lift your
foot off the accelerator) before the needle reaches the red zone.
Caution
2 ⇒ page 11, fig. 2 to go into
Never allow the rev counter needle A
the red zone on the dial for more than a very brief period: there is a
risk of damaging the engine. The start of the red zone on the dial is
different for some engine versions.
For the sake of the environment
•
Caution
Additional lights and other accessories in front of the air inlet
reduce the cooling effect of the radiator. At high outside temperatures and high engine loads, there is a risk of the engine overheating.
•
The front spoiler also ensures proper distribution of the cooling
air when the vehicle is moving. If the spoiler is damaged this can
reduce the cooling effect, which could cause the engine to overheat.
You should obtain professional assistance.
Changing up a gear early will help you to save fuel and minimise
engine noise.
SET button
This button has a number of different functions.
Fig. 3 Instrument
cluster: SET button
document_0900452a81b1b9de.book Seite 13 Donnerstag, 26. Juli 2007 9:16 09
Instruments and warning/indicator lamps
13
Time and date display
The SET button has the following functions:
Activating clock, date, temperature and mileage
recorder displays
The display will appear for about 30 seconds if you press the SET
button ⇒ page 12, fig. 3 when the ignition is switched off.
Starting check procedure (auto-check control)
The auto-check control checks important components and vehicle
systems. These background checks are run constantly, as long as
the ignition is switched on ⇒ page 30.
You can start the “check procedure” manually by pressing the SET
button with the ignition switched on. This function check can be
started at road speeds up to 5 km/h.
Calling up driver messages again
A red or yellow symbol appearing in the instrument cluster display
is normally accompanied by a corresponding message. The
message will disappear from the display after about 5 seconds. If
required, you can call up the message again by briefly pressing the
SET button.
Setting speed warning
You can press the SET button briefly to set speed limit warning 1
while the vehicle is moving ⇒ page 29. If you press and hold the
SET button, this will cancel the speed warning.
Fig. 4 Instrument
cluster: Time and date
display
Quartz clock
The date, time and display format can be changed using the sound
system or MMI* control console. Please refer to the sound system
or MMI* Operating Manual for more details.
Radio-controlled clock*
When the clock is in “radio-control” mode the signal reception
symbol (a radio tower with radio waves) appears in the display
⇒ fig. 4. It is then not possible to change the minutes or the date
manually.
•
Note
The digital clock and mileage recorder displays are switched on
for about 30 seconds when the driver's door is opened.
•
When the ignition is switched off, the clock and date display can
be switched on for about 30 seconds by pressing the SET button
⇒ page 12, fig. 3 ⇒ page 12.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 14 Donnerstag, 26. Juli 2007 9:16 09
14
Instruments and warning/indicator lamps
Mileage recorder
The instrument shows how far you have travelled.
The trip recorder can be reset to zero by pressing the reset button
0.0 ⇒ fig. 6.
Fault display
If there is a fault in the instruments, the letters dEF appear permanently in the trip recorder display. Please have the fault rectified as
soon as possible.
Immobiliser
When the ignition is switched on, the security programming of the
ignition key is verified electronically.
Fig. 5 Instrument
cluster: Mileage
recorder
If an uncoded key is used, SAFE will appear continuously in the
mileage recorder display. The vehicle cannot then be driven
⇒ page 43.
•
Note
The date, time and recorded mileage will continue to be
displayed for about 30 seconds after you switch off the ignition.
•
The digital clock and mileage recorder displays are switched on
for about 30 seconds when the driver's door is opened.
•
Fig. 6 Instrument
cluster: Reset button
When the ignition is switched off, the mileage recorder can be
switched on for about 30 seconds by pressing the SET button
⇒ page 12, fig. 3 ⇒ page 12.
The mileage is stated in kilometres (“km”) or “miles”.
You can switch the display from kilometres to miles and vice versa
via the sound system or MMI* using the CAR button on the control
console.
Odometer / trip recorder
The odometer records the vehicle's total mileage.
The trip recorder shows the distance that has been travelled since it
was last reset. It is used to measure individual journeys. The last
digit of the trip recorder indicates distances of 100 metres or tenths
of a mile.
Fuel gauge
The gauge only works when the ignition is switched on.
When the needle reaches the reserve zone, the symbol  ⇒ page 37
lights up in the instrument cluster display together with the
message Please refuel. At this point there are still about 8 litres of
fuel left in the tank. This is your reminder to fill up soon.
The tank capacity of your vehicle is given in the Technical data
section.
document_0900452a81b1b9de.book Seite 15 Donnerstag, 26. Juli 2007 9:16 09
Instruments and warning/indicator lamps
Caution
Never run the tank completely dry. The irregular supply of fuel can
cause misfiring, which would allow unburnt fuel to enter the
exhaust system. This can lead to overheating and damage to the
catalytic converter.
Warning and indicator lamps
Overview
The warning and indicator lamps indicate a number of
different functions and possible faults.
Fig. 7 Instrument cluster with warning and indicator lamps
Controls
Safety
Driving tips


Dynamic steering
⇒ page 16
Engine management (alternative
to )
⇒ page 16













(alternative to )
⇒ page 16
15
Electronic stabilisation program (ESP) ⇒ page 17
Airbag system
⇒ page 17
Tyre pressure monitoring
⇒ page 17
Left turn signals
⇒ page 18
Trailer turn signals*
⇒ page 18
Seat belt warning lamp
⇒ page 18
Emission control system
⇒ page 18
lane assist (active)
⇒ page 18
lane assist (inactive)
⇒ page 18
Main beam headlights
⇒ page 18
Right turn signals
⇒ page 18
Cruise control system*
⇒ page 19
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 16 Donnerstag, 26. Juli 2007 9:16 09
16
Instruments and warning/indicator lamps
⇒ page 19


Anti-lock brake system (ABS)
Electro-mechanical parking
brake/Audi hold assist*
⇒ page 20

Fault in brake system
⇒ page 20
Additional warning and indicator lamps are displayed on vehicles
equipped with the adaptive cruise control* ⇒ page 134.
•
Note
If the warning lamp  flashes, this indicates that the dynamic
steering is being initialised. The message “Dynamic steering: Initialising” ⇒ page 36 will appear in the driver information system
display.
•
The stabilisation functions of the dynamic steering ⇒ page 222
are not available in the event of a system malfunction.
Applies to vehicles: with petrol engine
Engine management
Note
A number of functions are monitored by the auto-check control
⇒ page 21. If a malfunction should occur, this will be shown by the
display in the instrument cluster either with a red symbol (priority 1
– serious malfunction) or a yellow symbol (priority 2 – other
malfunction or item requiring attention).
Applies to vehicles: with Audi drive select
Dynamic steering

If the warning lamp  lights up when you switch on the ignition and
goes out when the engine has started, the dynamic steering is activated.
If the warning lamp  stays on after the engine has started, this
indicates a malfunction in the system. You can continue driving
carefully at reduced speed to the next qualified workshop, however
the steering may feel heavier and its response may be more sensitive than usual. In addition, it is possible that the steering wheel will
be off centre when driving in a straight line.
WARNING
Have the system malfunction in the dynamic steering repaired by
a qualified workshop as soon as possible – risk of accident.

This warning lamp monitors the engine management
system on petrol engines.
The  warning lamp (Electronic Power Control) lights up when the
ignition is switched on to show that the lamp is working properly.
Note
If the warning lamp lights up while the vehicle is moving, this indicates a fault in the engine management system. The engine should
be serviced by a qualified workshop without delay.
Applies to vehicles: with diesel engine
Glow plug system

The indicator lamp lights up to show that the glow plugs
are preheating.
Your vehicle is equipped with an automatic glow plug system.
The indicator lamp  lights up while the glow plugs are preheating.
If the engine fails to start immediately, the glow plugs have not
finished preheating. In this case, keep the clutch pedal depressed
(or keep your foot on the brake if your vehicle has an automatic
gearbox) until the engine starts.
document_0900452a81b1b9de.book Seite 17 Donnerstag, 26. Juli 2007 9:16 09
Instruments and warning/indicator lamps
•
switching the ignition off and then on again. If the warning lamp
goes out, this means the system is fully functional.
Note
If the glow plug indicator lamp should start flashing while the
vehicle is moving, this indicates a fault in the engine management
system. The engine should be serviced without delay.
For further information on the ESP ⇒ page 222.
If the indicator lamp fails to light up when the ignition is
switched on, this can mean that the glow plug system is defective.
The engine should be serviced.
Airbag system
•
Electronic stabilisation program (ESP)

This warning lamp monitors the electronic stabilisation
program.
The warning lamp  has the following functions:
•
It flashes when the ESP or traction control system (ASR) intervenes while the vehicle is in motion.
•
The warning lamp will light up continuously if the ESP or the
traction control system (ASR) has been switched off using the ESP
OFF button ⇒ page 222.
•
It lights up when the ignition is switched on and should go out
again after about 2 seconds. This signals that the lamp is working
properly.
•
•
17
It will light up continuously if there is a malfunction in the ESP.
It will also come on if a fault should occur in the ABS because the
ESP operates in conjunction with the ABS.
If the battery has been disconnected, if the battery voltage is very
low, or if the engine has been started from an outside power source,
the ESP system will perform an initialisation of the various on-board
sensors while you drive the first few metres. The warning lamp will
light up during this period. It will go out when the initialisation has
been completed.

This warning lamp monitors the airbag and seat belt
tensioner system.
The warning lamp  should light up for a few seconds when the
ignition is switched on.
If the warning lamp does not go out, or if it lights up, flashes or
flickers when the vehicle is moving, this indicates a malfunction in
the system. This is also the case if the warning lamp does not light
up when the ignition is switched on.
WARNING
If a malfunction should occur, have the system checked immediately by a qualified workshop. If this is neglected, there is a risk
that the airbag system and/or belt tensioners may not be activated in an accident.
Tyre pressure monitoring

The tyre pressure should be corrected as soon as possible
if it is too low.
If the  symbol flashes for about a minute and then remains lit after
you switch on the ignition, there is a fault in the system. Please
contact the nearest qualified workshop as soon as possible.
For more detailed information on the tyre pressure monitoring
system, please refer to ⇒ page 39.
If the warning lamp lights up and stays on after the engine is
started, this may mean that the control system has temporarily
switched off the ESP. In this case the ESP can be reactivated by
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 18 Donnerstag, 26. Juli 2007 9:16 09
18
Instruments and warning/indicator lamps
Turn signals

Emission control system

Depending on which turn signal is operated, either the left  or
right  indicator lamp flashes. Both indicator lamps will flash when
the hazard warning lights are switched on.
If the warning lamp lights up continuously you should take your
vehicle to a qualified workshop as soon as possible in order to have
the fault rectified.
If one turn signal should fail, the indicator lamp will start flashing
twice as fast.
If the warning lamp flashes drive on at reduced speed and seek
professional help in order to avoid damage to the catalytic
converter.
This does not apply when towing a caravan or trailer. The indicator
lamp will stop flashing if one of the turn signals on the vehicle or the
caravan/trailer should fail. For further information on the turn
signals ⇒ page 62.
For further information on the catalytic converter ⇒ page 229.
Applies to vehicles: with lane assist
lane assist (active)

Applies to vehicles: with towing bracket
Trailer turn signals

The indicator lamp flashes when the turn signals are
operated while towing a caravan or trailer.
The indicator lamp  flashes when the turn signals are operated,
provided a caravan or trailer is correctly attached and connected to
the vehicle.
The indicator lamp will not flash if one of the turn signals on the
trailer fails.
Seat belt warning lamp

The warning lamp acts as a reminder to fasten the seat
belts.
The indicator lamp confirms that the system is fully functional. You
will be warned if you are about to cross the lane markings detected
by the system.
For more information on the lane assist system, please see
⇒ page 145.
lane assist (inactive)

The warning lamp indicates that the system is switched on.
However, you will not be warned if you cross the lane markings.
For more information on the lane assist system, please see
⇒ page 145.

After switching on the ignition, the warning lamp  will remain lit
until the driver and front passenger (if applicable) have fastened
their seat belts. When the vehicle has gathered speed you will also
hear a warning chime.
Main beam headlights
For further information on the seat belts ⇒ page 194.
For further information on the main beam headlights ⇒ page 62.
The indicator lamp  lights up when the main beams are on or
when the headlight flasher is operated.
document_0900452a81b1b9de.book Seite 19 Donnerstag, 26. Juli 2007 9:16 09
Instruments and warning/indicator lamps
Fault on the electronic differential lock (EDL)
Applies to vehicles: with cruise control system
Cruise control

The indicator lamp  in the instrument cluster lights up when the
cruise control system is operating.
Anti-lock brake system (ABS)
WARNING
The warning lamp  lights up for a few seconds when the ignition
is switched on and while the engine is being started. The lamp goes
out again once the system has run through an automatic test
sequence.
There is a fault in the ABS if:
• the warning lamp  does not light up when the ignition is
switched on,
the warning lamp does not go out again after a few seconds,
the warning lamp lights up when the vehicle is moving.
The vehicle can still be braked in the normal way (except that the
ABS control function is out of action). Please take the vehicle to a
qualified workshop as soon as possible. For further information on
the ABS ⇒ page 222.
If a fault occurs in the ABS, the ESP warning lamp will also light up.
Fault in the main brake system
If the ABS warning lamp  lights up together with the brake
warning lamp  ⇒ page 32, this indicates a fault in the ABS function, and possibly a malfunction in the main brake system as well
⇒
.
If there is a malfunction in the brake system the symbol  will light
up in the instrument cluster. Please refer to ⇒ page 32.
Controls
Safety
The EDL works in conjunction with the ABS. If a malfunction should
occur in the EDL, this is indicated by the ABS warning lamp .
Please take the vehicle to a qualified workshop as soon as possible.
For further information on the EDL ⇒ page 222.

The warning lamp monitors the ABS and the electronic
differential lock (EDL).
•
•
19
Driving tips
•
Before opening the bonnet and checking the brake fluid level,
observe the warning information on ⇒ page 255, “Working on
components in the engine compartment”.
•
If the brake warning lamp  should light up together with the
ABS warning lamp , stop the vehicle immediately and check the
brake fluid level in the reservoir. If the fluid level has dropped
below the "MIN" mark you must not drive on - otherwise there may
be an increased accident risk. You should obtain professional
assistance.
•
If the brake fluid level is OK, the fault in the brake system may
have been caused by a failure of the ABS control function. As a
result the rear wheels can lock relatively easily when braking. This
could cause the tail of the vehicle to skid sideways. Drive carefully
to the nearest qualified workshop and have the fault rectified.
Applies to vehicles: with Audi hold assist
Audi hold assist

This warning lamp monitors the Audi hold assist function.
Audi hold assist helps the driver to keep the vehicle stationary while
the engine is running, for instance on steep gradients, at traffic
lights or in stop-and-go traffic. When the Audi hold assist function
is on, you don't have to keep your foot on the brake to prevent the
vehicle from accidentally rolling away. Once it detects that the
vehicle is stopped, Audi hold assist keeps the vehicle stationary. The
green symbol  in the instrument cluster indicates that the function is activated. You can now take your foot off the brake pedal.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 20 Donnerstag, 26. Juli 2007 9:16 09
20
Instruments and warning/indicator lamps
When the vehicle has been stationary for an extended period, Audi
hold assist will automatically apply the parking brake. In this case,
the green symbol  will change to red .
Electro-mechanical parking brake
If a failure should occur in the ABS, the ABS warning lamp  will
light up together with the brake warning lamp  ⇒
.

This warning lamp monitors the electro-mechanical
parking brake.
The warning lamp  lights up when the parking brake is applied
with the ignition on. After the ignition has been switched off the
lamp will stay on for about 30 seconds. The warning lamp will light
up for about 30 seconds if the parking brake is applied with the ignition switched off.
The warning lamp should go out when the parking brake is released.
If the warning lamp flashes continuously after the parking brake has
been applied, the brake may not be strong enough to hold the
vehicle on a slope. This may be due to the brakes overheating.
Please note the following points:
•
If the gradient is too steep to park the vehicle safely, the display
will show the message Caution: Vehicle parked too steep.
•
In the event of a fault in the parking brake system the symbol 
will also appear in the instrument cluster display together with the
message Parking brake! You should have the fault corrected by a
qualified workshop without delay.
Brake system
same time. You can press the SET button to obtain a message
explaining the fault ⇒ page 32.

The warning lamp flashes if the brake fluid level is too low
or if there is a fault in the ABS system or the parking
brake.
If the warning lamp  flashes, there is a fault in the brake system.
The symbol  in the instrument cluster display will flash at the
WARNING
•
Before opening the bonnet and checking the brake fluid level,
observe the warning information on ⇒ page 255, “Working on
components in the engine compartment”.
•
If the brake warning lamp does not go out, or if it lights up
when driving, the brake fluid level in the reservoir is too low – this
may cause an increased accident risk. Stop the vehicle and do not
drive on. You should obtain professional assistance.
•
If the brake warning lamp lights up together with the ABS
warning lamp, this can mean that the control function of the ABS
is out of action. As a result the rear wheels can lock relatively
easily when braking. This could cause the tail of the vehicle to skid
sideways. Drive carefully to the nearest qualified workshop and
have the fault rectified.
document_0900452a81b1b9de.book Seite 21 Donnerstag, 26. Juli 2007 9:16 09
Driver information system
21
Driver information system
Introduction
General notes
The driver information system in the instrument cluster
shows you the status of various on-board systems at a
glance.
Fig. 8 Dashboard:
Display in instrument
cluster (automatic
gearbox)
The display for the driver information system is in the centre of the
instrument cluster.
The system runs a check on certain components and functions
when the ignition is switched on and while the vehicle is moving. It
gives an audible warning if a fault should occur or if servicing is
required, and a red or yellow warning symbol (in some cases with a
corresponding driver message) appears in the dashboard display.
CD and radio display
⇒ page 22
Outside temperature
⇒ page 22
Gear-change indicator
⇒ page 22
Digital speedometer*
⇒ page 23
Door catches/boot lid warning
⇒ page 24
Service interval display
⇒ page 24
Auto-check control*
⇒ page 30
Driver messages
⇒ page 30
Speed warning
⇒ page 28
On-board computer*
⇒ page 25
Selector lever positions for automatic gearbox*
⇒ page 163
Note
If a fault should occur, the display will show a red or yellow warning
symbol. A red warning symbol indicates a serious malfunction
⇒ page 31. A yellow warning symbol indicates a less serious
malfunction, or other item requiring attention ⇒ page 35.
The system will also display information for the radio and CD player
and (if fitted) the route guidance directions from the navigation
system*. For further information on these systems, please refer to
the sound system or MMI* Operating Manual.
On some models the display of information shown in the instrument cluster differs from the illustrations used here.
The driver information system includes the following functions:
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 22 Donnerstag, 26. Juli 2007 9:16 09
22
Driver information system
CD and radio display
At temperatures below +5°C a snowflake symbol appears next to the
temperature display. This is to warn the driver to take extra care
when there is a risk of ice on the road.
When the vehicle is stationary or travelling at very low speeds, the
temperature displayed may be slightly higher than the actual
outside temperature as a result of the heat radiated from the
engine.
Fig. 9 Display: Radio
information
If no priority 1 or 2 faults have been detected by the auto-check
control, the name or frequency of the current radio station and the
selected waveband will appear the upper part of the display.
When a CD is playing, the display will show the current title. If the
vehicle is equipped with a CD changer* the display will also show
the number of the CD being played (CD1 to CD6).
The temperature units can be set to °F or °C on the sound system or
MMI* system. The outside temperature is automatically displayed in
the units you have selected. Please refer to the sound system or
MMI* Operating Manual for further details.
WARNING
Do not rely on the outside temperature display as an ice warning.
Please bear in mind that there may be patches of ice on the roads
even at outside temperatures around +5°C.
Applies to vehicles: with manual gearbox and gear-change indicator
Gear-change indicator
Outside temperature display
The outside temperature is shown when the display is
activated.
This additional indicator function can help to save fuel.
Fig. 11 Display: Gearchange indicator
Fig. 10 Display:
Outside temperature
document_0900452a81b1b9de.book Seite 23 Donnerstag, 26. Juli 2007 9:16 09
Driver information system
23
certain situations, only the driver can choose the correct gear (for
instance when overtaking, driving up a steep gradient or towing a
trailer).
•
The gear-change indicator in the instrument cluster ⇒ page 22,
fig. 11 goes out when you press the clutch pedal.
Fig. 12 Display:
Switching the gear
change indicator on
and off
Applies to vehicles: with on-board computer
Digital speedometer
You can activate and deactivate the gear-change indicator
on the sound system or MMI*.
Switching the gear-change indicator on and off
– Select: Function selector button CAR > Instrument
cluster > Suggested gear ⇒ fig. 12.
To familiarise yourself with the gear-change indicator, we recommend driving in the normal way to start with. A gear change will be
recommended if the gear you are in is not the most economical
choice. The gear you are currently in and the recommended gear
will be displayed ⇒ page 22, fig. 11.
Fig. 13 Display: Digital
speedometer
The display shows the current speed. The speed is displayed in
increments of 1 km/h.
•
Shifting up a gear: The suggested gear appears to the right of the
current gear when a higher gear is recommended.
•
Shifting down a gear: The suggested gear appears to the left of
the current gear when a lower gear is recommended.
Gears may ocassionally be skipped (3 > 5). If no gear-change is
recommended, you are already in the most economical gear.
•
Note
The gear-change indicator is intended to help save fuel. It is not
intended to recommend the right gear for all driving situations. In
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 24 Donnerstag, 26. Juli 2007 9:16 09
24
Driver information system
Door catches / boot lid warning
Service interval display
The pictogram shows whether the doors and the boot lid,
etc. are properly closed when driving off.
The service interval display detects when the next service
is due for your vehicle.
Fig. 14 Display: Door
catches/boot lid
warning
Fig. 15 Instrument
cluster display: Service
interval display
The door catches/boot lid warning symbol lights up if one or more
of the doors, or the bonnet or boot lid are not properly closed when
the ignition is on. The symbol also indicates which of these is not
properly closed ⇒ fig. 14.
The warning symbol disappears when all the doors, the bonnet and
the boot lid are completely closed, and the driver information functions selected will then be displayed again.
Fig. 16 Display:
Service interval display
You can see whether an oil change or service inspection is due in
the Car menu on the sound system or MMI display. There are two
display levels:
•
Service reminder: When the next service date is approaching,
Service in----- km--- days ⇒ fig. 15 will be shown in the instrument
cluster display each time you switch on the ignition. The number of
days and kilometres act independently of each other. Service due!
will appear in the display when the number of days reaches zero,
even if you have not yet driven the estimated number of kilometres
remaining. Similarly, Service due! will appear in the display when
document_0900452a81b1b9de.book Seite 25 Donnerstag, 26. Juli 2007 9:16 09
Driver information system
the number of kilometres reaches zero, even if the estimated period
has not yet expired. The remaining distance and time are updated
and displayed briefly each time you switch on the ignition.
•
Service due: When a service is due, Service due! will appear in
the display as soon as you switch on the ignition. The display reverts
back to the standard display after a short time. In addition, a tone
will sound.
Displaying distance and time to next service
In the Car menu, you can look up the distance and time remaining
until the next oil change and next service inspection. To do this,
select function selector button CAR > Service interval display
⇒ page 24, fig. 16.
•
25
Note
Do not reset the display between oil changes - otherwise the
display will be incorrect.
•
The information in the service interval display remains intact if
the battery is disconnected.
•
The distance to the next service cannot be called up if the system
has detected a Priority 1 fault (red symbol).
•
If the service was not performed by a qualified workshop, the oil
change interval display can only be set to “fixed service intervals” of
15,000 km. If you wish to continue with the “LongLife” service, you
will need to have the oil change interval display reset by a qualified
workshop.
The display may not be complete on new vehicles within the first
500 km.
On-board computer
Resetting the service interval display
Your Audi dealer resets the display after each service. You can only
reset the oil change display yourself. To do this, select function
selector button CAR > Service interval display > Reset oil change
interval. The next oil change will be indicated as being due
15,000 km or one year (fixed service interval) after the oil change
interval is reset.
Applies to vehicles: with on-board computer
Introduction
The on-board computer provides you with useful information during a journey, including average and current fuel
consumption, average speed, fuel range and driving time.
Caution
The system cannot calculate the figures for the service indicator if
the battery is disconnected from the vehicle, so no service reminder
can be displayed during this time. Please remember that keeping to
the correct service intervals is most important for the service life
and residual value of the vehicle (and especially for the life of the
engine). The period between two services must never be longer
than the time specified in the Service Schedule, even if you only
cover a low mileage during this time.
Controls
Safety
Driving tips
Fig. 17 On-board
computer: Fuel range
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 26 Donnerstag, 26. Juli 2007 9:16 09
26
Driver information system
Average speed
This mode shows the average speed driven since the memory was
last cancelled (in km/h).
Driving time
This display shows the period of time which has elapsed since the
memory was last cancelled.
Fig. 18 On-board
computer: Average fuel
consumption
The following items of information are processed by the on-board
computer and can be shown one after the other on the display in the
instrument cluster.
Fuel range
The estimated fuel range is displayed in km. It shows how far the
vehicle can be driven with the amount of fuel left in the tank,
assuming the same style of driving. The fuel range is displayed in
increments of 10 km.
The fuel range is calculated on the basis of the fuel consumption
over the last 30 kilometres. The fuel range will increase accordingly
if you drive in a more economical manner.
Average fuel consumption
This mode displays the average fuel consumption since the memory
was last cancelled in litres/100 km. If required, you can use this
display to adjust your driving style to achieve the desired fuel
consumption.
Distance covered
This display shows the distance you have covered since the memory
was last cancelled.
•
Note
The displays for fuel consumption (average and current
consumption), fuel range and speed are shown in metric units. You
can change the measurement units via the sound system or MMI*.
•
The information in the memory is cancelled if the battery is
disconnected.
Applies to vehicles: with on-board computer
Memory
The on-board computer has two automatic journey
memories.
Current fuel consumption
The display shows the current fuel consumption in litres/100 km. If
required, you can use this display to adjust your driving style to
achieve the desired fuel consumption.
The computer calculates the fuel consumption every 30 metres. The
display switches to l/h (litres per hour) when the vehicle is
stationary.
Fig. 19 On-board
computer: Memory 1
document_0900452a81b1b9de.book Seite 27 Donnerstag, 26. Juli 2007 9:16 09
Driver information system
B ⇒ fig. 20 to switch back and forward
Press RESET button A
between the functions of on-board computers 1 and 2.
The number in the display ⇒ page 26, fig. 19 indicates which of the
two memories is currently in use. The figure 1 means that the
display is showing the information in the single journey memory
(on-board computer 1). The figure 2 means that the display is
showing the information in the total journey memory (on-board
computer 2).
27
Applies to vehicles: with on-board computer
Controls
The on-board computer is controlled by means of two
switches on the windscreen wiper lever.
Single journey memory (on-board computer 1)
The single journey memory processes the information on a journey
from the time the ignition is switched on until it is switched off. If
the journey is resumed within two hours after the ignition is
switched off, the new figures are automatically included in the
calculation. The memory is automatically deleted when you resume
driving, if the journey is interrupted for more than two hours.
Total journey memory (on-board computer 2)
Unlike the single journey memory, the total journey memory is not
erased automatically. In this way, you can determine the period for
which you wish the on-board computer to supply figures.
Fig. 20 Windscreen
wiper lever: On-board
computer controls
– Press the top or bottom of the function selector switch
A ⇒ fig. 20. This displays the on-board computer readA
outs one after the other.
The on-board computer can only be operated while the ignition is
switched on. When the ignition is switched on, the display shows
the function that was last selected.
As well as the figures from the on-board computer (computer 1 or
2), the display can also show information from other systems. Press
B briefly to switch back and forward between
the Reset button A
these displays.
Resetting figures to zero
To cancel one of the computer readings individually, select the
B for at least one
required function and press the RESET button A
second. The following values can be reset to zero individually using
the Reset button:
•
•
Controls
Safety
Driving tips
Average fuel consumption
Average speed
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 28 Donnerstag, 26. Juli 2007 9:16 09
28
Driver information system
•
•
Driving time
and can be switched back on at any time so that they again appear
in the display.
Distance covered
You can also cancel all the values in the single journey memory or
the total journey memory at the same time ⇒ page 28.
Speed warning function
Applies to vehicles: with speed warning function
Note
The information in the memory is cancelled if the battery is
disconnected.
Introduction
The speed warning function can help you keep below a
pre-set maximum speed.
Applies to vehicles: with on-board computer
Basic settings for the on-board computer
The basic settings for the on-board computer can be
adjusted via the sound system or MMI*.
The speed warning function will warn you if the vehicle exceeds the
pre-set maximum speed. The system gives an audible warning
signal if the set speed is exceeded by about 3 km/h. A warning
symbol will also appear in the display . On some models the symbol
may look slightly different.
The speed warning function has two different warning speeds,
which operate independently and serve slightly different purposes:
Speed limit warning 1

With speed limit warning 1, the maximum speed can be changed
while driving. The speed limit that has been set remains stored until
the ignition is switched off, or until it is changed or cleared.
Fig. 21 MMI display:
On-board computer
The speed limit warning symbol  for speed limit warning 1 will
appear in the display if you exceed the pre-set speed. It goes out
again if the speed is reduced below the set speed limit.
– Select: Function selector button CAR > Instrument
cluster > On-board computer 1 or On-board computer 2.
The symbol also goes out if the speed is increased to more than
about 40 km/h above the set speed for at least 10 seconds. This
cancels the speed limit that was originally set.
You can zero all the values in the single journey memory or the total
journey memory at the same time by selecting the Reset menu item.
Setting speed limit warning 1 ⇒ page 29.
You can also define which items of information you wish to have
displayed by the on-board computer. If one of these items is
switched off, it will not appear in the display. However, the corresponding figures will still be registered by the on-board computer
You are recommended to store this speed limit warning if you
always wish to be reminded of a particular speed limit. This could
be when driving in countries with general speed limits, or if you
Speed limit warning 2

document_0900452a81b1b9de.book Seite 29 Donnerstag, 26. Juli 2007 9:16 09
Driver information system
need to keep below a particular speed when winter tyres are fitted,
etc.
The speed limit warning symbol  for speed warning 2 will appear
in the display if you exceed the pre-set speed. Unlike speed limit
warning 1, the warning symbol only goes out once the road speed
has dropped below the stored value again.
Setting speed limit warning 2 ⇒ page 29.
Note
Please bear in mind that, even with the speed warning function, it is
still important to keep a check on the car's speed with the speedometer and to observe the statutory speed limits.
29
Clearing speed limit
– Drive the vehicle at a minimum of 5 km/h.
– Press the SET button for at least 2 seconds.
The speed warning symbol  lights up briefly in the display to
confirm that the selected speed has been stored. The speed limit
that has been set remains stored until another speed is set with a
brief push of the button, or until the memory is cleared with a long
push of the button.
When the speed limit has been cleared, the display will show a
crossed-out warning symbol .
Applies to vehicles: with speed warning function
Setting speed limit warning 2
Applies to vehicles: with speed warning function
Setting speed limit warning 1
You can use the SET button to set, alter or cancel speed
limit warning 1.
You can use the sound system or MMI* to set, alter or
cancel speed limit warning 2.
Fig. 23 Display:
Setting speed limit
warning 2
Fig. 22 Detail of the
instrument cluster:
SET button
Selecting speed limit
– Select: Function selector button CAR > Instrument
cluster > Speed warning.
– Drive at the desired maximum speed.
•
– Press the SET button in the instrument cluster ⇒ fig. 22
for one second.
Controls
Safety
Driving tips
Speed warning on/off - to activate or deactivate the speed
warning function ⇒ fig. 23.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 30 Donnerstag, 26. Juli 2007 9:16 09
30
Driver information system
•
Speed warning - to set the speed above which a warning signal
will sound.
Speed limit warning 2 can be adjusted in increments of 10 km/h
between 30 and 240 km/h.
Auto-check control
If one or more faults are detected, the driver information message
(as above) will disappear about 15 seconds after the engine has
been started and the appropriate fault symbol(s) will appear in the
display. The warning display will be accompanied by the corresponding warning chime.
Applies to vehicles: with speed warning function
Driver messages
Introduction
The auto-check control checks important components and vehicle
systems. These background checks are run constantly, as long as
the ignition is switched on.
Additional messages to assist the driver are displayed
together with the warning symbols in the instrument
cluster.
A message is displayed in the instrument cluster if a fault should
occur or if any maintenance or repairs are urgently required. This is
accompanied by an audible warning signal. Depending on the
priority of the fault, a red or yellow warning symbol lights up in the
display.
The red symbols indicate a serious malfunction, whereas the yellow
ones represent other malfunctions or items requiring attention.
Additional messages to assist the driver may be shown with the red
or yellow symbols.
Automatic gearbox* function test
The auto-check control automatically checks the vehicle systems
when the ignition is switched on. If the selector lever is in position
P or N, the following instruction will appear:
When stationary apply footbrake while selecting gear
When a gear (R, D etc.) is selected, this message disappears and the
auto-check control function is displayed.
The driver message will disappear 30 seconds after switching on
the ignition or earlier, if there are other driver messages or malfunctions.
Fig. 24 Instrument
cluster: SET button
For example, the following driver message will appear if the selector
lever for the automatic gearbox* is not in position P when you
switch off the engine:
Shift to P, otherwise vehicle can roll away. Doors do not lock if
lever is not in P.
The ignition key can only be withdrawn when the selector lever is in
this position. Similar messages will be displayed if other functions
of this kind cannot be carried out.
Driver messages and red symbols
If a red warning symbol appears in the display, it will automatically
be accompanied by the corresponding driver message.
document_0900452a81b1b9de.book Seite 31 Donnerstag, 26. Juli 2007 9:16 09
Driver information system
For example, in the event of an oil pressure malfunction the oil pressure symbol  will appear in the display. In addition, the following
message will appear:
Switch off engine and check oil level
The message will disappear from the display after about 5 seconds.
If required, the message can be called up again by briefly pressing
the SET button ⇒ page 30, fig. 24.
Driver messages and yellow symbols
If a yellow warning symbol appears in the display, it will automatically be accompanied by the corresponding driver message.
For example, if the symbol  appears (windscreen washer fluid
low), the display will also show the message:
31
– Switch off the engine.
– Check the function displayed. Obtain professional assistance if necessary.
The red symbols indicate a Priority 1 fault (serious malfunction).
Should a Priority 1 fault occur, a red warning symbol will appear at
the top of the display ⇒ fig. 25. The symbol is accompanied by a
driver message giving you more information about the fault. This
symbol is accompanied by three warning chimes. The symbol will
keep flashing until the fault is corrected.
If several Priority 1 faults are detected at the same time, the symbols
are displayed one after the other for about 2 seconds at a time.
This message will disappear after about 5 seconds, but you can call
it up again at any time by pressing the SET button ⇒ page 30.
Please top up washer fluid
The message will disappear after a few seconds. If required, the
message can be called up again by briefly pressing the SET
button.
Red symbols
A red symbol warns of a serious malfunction.
Fig. 25 Display:
Symbol for serious
malfunction


Alternator fault
⇒ page 32
Fault in brake system/parking
brake
⇒ page 32

Coolant level too low / coolant
temperature too high
⇒ page 33
Engine oil pressure too low
⇒ page 33
Add engine oil immediately
⇒ page 34
Fault in the steering system
⇒ page 34
Ignition lock defective
⇒ page 34
Tyre pressure monitoring
⇒ page 39





– Stop the vehicle.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 32 Donnerstag, 26. Juli 2007 9:16 09
32
Driver information system
Alternator fault

Warning! Fault in ABS brake system. Contact
workshop
If the symbol  flashes in the instrument cluster display, there is an
alternator fault or a fault in the vehicle's electrical system. In addition, a message will appear. This message will disappear after about
5 seconds, but you can call it up again at any time by pressing the
SET button.
You should normally be able to drive to the next available qualified
workshop. However, you should avoid using electrical equipment
that is not absolutely necessary because this will drain the battery.
Caution
If the coolant warning lamp  in the instrument display lights up
as well as the alternator warning lamp while driving ⇒ page 33, stop
the vehicle immediately and switch off the engine. In this case the
coolant pump is no longer being driven, and there is a risk of engine
damage.
Fault in the brake system

A fault in the brake system should be corrected as soon as
possible.
If the symbol  flashes in the display, there is a fault in the
brake system. The symbol is accompanied by a driver
message giving you more information about the fault. This
message will disappear after about 5 seconds, but you can
call it up again at any time by pressing the SET button:
Stop vehicle and check brake fluid level
– Stop the vehicle.
– Check the brake fluid level ⇒ page 262.
– Obtain professional assistance if necessary.
– Drive carefully to the nearest qualified workshop and
have the fault rectified ⇒
.
Parking brake ! Please contact workshop
– If the symbol appears after you switch on the ignition
when the vehicle is stationary, please check whether you
can release the parking brake. If this is possible, you
should drive without delay to the nearest qualified workshop and have the fault rectified. If the parking brake
cannot be released you should obtain professional
assistance.
– If this symbol should appear while driving, there may be
a malfunction in the drive-away assist or the emergency
brake functions. You may not be able to apply the parking
brake. It is also possible that you cannot release the
parking brake after it has been applied. Drive the vehicle
to a qualified workshop and have the fault repaired.
If the ABS fails, the ABS warning lamp  will light up together with
the brake warning symbol  ⇒
.
WARNING
•
Before opening the bonnet and checking the brake fluid level,
observe the warning information on ⇒ page 255, “Working on
components in the engine compartment”.
•
If the brake fluid level in the reservoir is too low, this could
result in an accident. Do not drive on. You should obtain professional assistance.
•
If the brake warning lamp lights up together with the ABS
warning lamp, this can mean that the control function of the ABS
is out of action. As a result the rear wheels can lock relatively
document_0900452a81b1b9de.book Seite 33 Donnerstag, 26. Juli 2007 9:16 09
Driver information system
33
If the alternator warning lamp lights up as well ⇒ page 32, it is
possible that the drive belt has broken.
WARNING (continued)
easily when braking. This could cause the tail of the vehicle to skid
sideways. Drive carefully to the nearest qualified workshop and
have the fault rectified.
Note
The warning lamp  in the instrument cluster will start flashing as
well if there is a fault in the brake system.
Fault in the cooling system

Faults in the cooling system must be rectified immediately.
If the  symbol flashes in the display, this means that
either the coolant temperature is too high or the coolant
level is too low. The symbol is accompanied by a driver
message giving you more information about the fault. This
message will disappear after about 5 seconds, but you can
call it up again at any time by pressing the SET button:
Switch off engine, check coolant level
WARNING
•
If your vehicle should break down for technical reasons, stop it
at a safe distance away from moving traffic, switch off the engine
and turn on the hazard warning lights ⇒ page 61, “Hazard
warning lights ”.
•
Never open the bonnet if you can see or hear steam or coolant
escaping from the engine compartment; there is a risk of being
scalded. Wait until you can no longer see or hear escaping steam
or coolant.
•
The engine compartment of any motor vehicle is a dangerous
place. Before carrying out any work in the engine compartment,
switch off the engine and allow it to cool down. Please observe the
important safety warnings ⇒ page 255, “Working on components
in the engine compartment”.
Caution
Do not drive on if the symbol  has come on to indicate a fault in
the cooling system, otherwise there is a risk of damaging the
engine.
– Stop the vehicle.

– Switch off the engine.
Engine oil pressure too low
– Check the coolant level ⇒ page 261.
If the engine oil pressure is too low the fault must be rectified immediately.
– Add more coolant if necessary ⇒ page 261.
– Wait for the symbol to go out before driving on.
– Obtain professional assistance if necessary.
If the  symbol flashes in the display, the oil pressure is
too low. The symbol is accompanied by a driver message
giving you more information about the fault. This message
If the coolant level is correct, the overheating may be caused by a
malfunction of the radiator fan.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 34 Donnerstag, 26. Juli 2007 9:16 09
34
Driver information system
will disappear after about 5 seconds, but you can call it up
again at any time by pressing the SET button:
Switch off engine and check oil level
– Stop the vehicle.
– Switch off the engine.
– Check the engine oil level ⇒ page 258.
– Obtain professional assistance if necessary.
If the engine oil level is too low
If the engine oil level is too low, add more oil ⇒ page 259.

The steering wheel cannot be unlocked if there is a fault
in the electronic steering lock.
If the symbol  flashes in the display, there is a malfunction in the electronic steering lock. The symbol is accompanied by a driver message giving you more information
about the fault. This message will disappear after about
5 seconds, but you can call it up again at any time by
pressing the SET button:
Do not drive vehicle. Steering defective
– You should obtain professional assistance.
If the engine oil level is correct
If the  symbol flashes and the engine oil level is correct, obtain
professional assistance. Do not drive on. Do not continue to run the
engine, not even at idle speed.
Note
The oil pressure warning lamp  is not an indicator for the oil
level. The oil level should therefore be checked regularly.
Add engine oil immediately
Fault in the steering system

– Do not have the vehicle towed away.
WARNING
The vehicle must not be towed if there is a fault in the electronic
steering lock: the steering will be locked and the vehicle cannot be
steered. Towing a vehicle with locked steering can cause an accident.
Note
On some models the symbol may look slightly different.
 WARNING! Please add oil immediately
If the  symbol lights up, you must add oil immediately
⇒ page 259.
Ignition lock defective

A fault in the ignition lock must be rectified immediately.
If the symbol  flashes in the display, there is a malfunction in the electronic ignition lock. The symbol is accompanied by a driver message giving you more information
about the fault. This message will disappear after about
document_0900452a81b1b9de.book Seite 35 Donnerstag, 26. Juli 2007 9:16 09
Driver information system
5 seconds, but you can call it up again at any time by
pressing the SET button:
Ignition lock defective. Contact workshop!
– Do not switch off the engine.
– Drive the vehicle without delay to a qualified workshop
and have the fault repaired.
The ignition cannot be switched off if there is a fault in the electronic ignition lock. For this reason, you should drive the vehicle
without delay to a qualified workshop and have the cause of the
fault repaired.
If the vehicle is equipped with the advanced key* feature, you
should not switch off the engine with the Stop/Start button because
it cannot be started again after the ignition has been switched off.
Note
On some models the symbol may look slightly different.
Yellow symbols
A yellow symbol indicates a malfunction or other item
requiring attention.
Fig. 26 Display: Yellow
warning symbol
Controls
Safety
Driving tips
35
Yellow symbols indicate a Priority 2 fault.
Yellow symbols are accompanied by one warning chime. The
symbol is accompanied by a driver message giving you more information about the fault. This message will disappear after about
5 seconds, but you can call it up again at any time by pressing the
SET button.
The function indicated should be checked as soon as possible. The
yellow symbol will only go out when the fault has been rectified.
If several Priority 2 faults are detected at the same time, the symbols
are displayed one after the other for about 2 seconds at a time.

Dynamic steering
⇒ page 36 and
⇒ page 159



Brake pads worn
⇒ page 37
Battery power*
⇒ page 38
Bulb monitor*
Bulb failure*
⇒ page 37

Check engine oil level
⇒ page 38 or
⇒ page 38




Engine oil sensor defective
⇒ page 38
Fuel level low
⇒ page 37
Washer fluid level low*
⇒ page 37
advanced key*
Key not in vehicle
⇒ page 36

Light sensor/rain sensor defec- ⇒ page 37
tive

Diesel particulate filter*
obstructed
General maintenance
⇒ page 38
Self-help
Technical data
document_0900452a81b1b9de.book Seite 36 Donnerstag, 26. Juli 2007 9:16 09
36
Driver information system

Dynamic headlight range control* defective
⇒ page 39


Battery in remote control key
⇒ page 44
Electro-mechanical
parking brake
⇒ page 123




adaptive light* defective
⇒ page 39
Ignition lock defective
⇒ page 39
Windscreen wiper defective
⇒ page 39
Suspension control
⇒ page 39
TPMS
Tyre pressure monitoring system
⇒ page 39
than usual. In addition, it is possible that the steering wheel will be
off centre when driving in a straight line.
Dynamic steering: initialising
If this message appears and the warning lamp  flashes in the
instrument cluster, this indicates that the dynamic steering is being
initialised. The steering wheel will move slightly after the engine is
started. The dynamic steering may be initialised if the steering
wheel was moved while the vehicle was stopped. The warning lamp
will go out when the initialisation has been completed.
WARNING
Have the system malfunction in the dynamic steering repaired by
a qualified workshop as soon as possible – risk of accident.
Note
The stabilisation functions of the dynamic steering ⇒ page 222 are
not available in the event of a system malfunction.
Note
On some models the speed limit warning 1  and speed limit
warning 2  will also be displayed as yellow symbols. These always
appear as a small symbol at the top of the display ⇒ page 28.
Applies to vehicles: with advanced key
Key not in vehicle

 Key not in vehicle
Applies to vehicles: with Audi drive select
Dynamic steering

 Dynamic steering: system fault
This message and the  symbol will appear if a fault develops in the
system while the vehicle is moving. You can continue driving carefully at reduced speed to the next qualified workshop, however the
steering may feel heavier and its response may be more sensitive
This message will appear together with the symbol  if the remote
control key is removed from the vehicle while the engine is running.
This is to remind you not to continue driving without the key (for
example if you change drivers).
If the remote control key is not in the vehicle you will not be able to
switch on the ignition or restart the engine after it has been
switched off. You will also not be able to lock the vehicle from the
outside.
document_0900452a81b1b9de.book Seite 37 Donnerstag, 26. Juli 2007 9:16 09
Driver information system
Light sensor / rain sensor defective

WARNING
 Automatic headlights / automatic wipers defective
If the  symbol appears, this means that the light sensor / rain
•
sensor is not functioning.For safety reasons, the dipped beam headlights will then be switched on permanently when the light switch
is set to the AUTO position. However, you can still switch the lights
on and off in the normal way with the light switch. If the rain sensor
is defective, the functions operated via the windscreen wiper lever
will still be available. You should have the light sensor / rain sensor
checked by a qualified workshop as soon as possible.
Incorrect handling of the high-voltage element of xenon gasdischarge bulbs* can have potentially fatal consequences.
Brake pads worn

•
Note
Have the components repaired or replaced by a qualified
workshop.
Washer fluid level low
safety's sake the rear pads as well) inspected by a qualified
workshop.

 Please top up washer fluid
If the  symbol lights up, top up the fluid for the windscreen
washer and headlight washer system* ⇒ page 267.
Fuel level low
Applies to vehicles: with bulb monitor


The bulb monitor checks whether the lights on the vehicle
are working.
The bulb monitor checks whether the lights on the vehicle are
working. If it detects a defective bulb on the vehicle it will show a
yellow warning symbol together with a message indicating which
light is not working.
Bulb failure
Bulbs are sensitive to pressure. The glass can break when you
touch the bulb, causing injury.
Applies to vehicles: with washer fluid warning system
 Brake pads!
If the  symbol lights up, have the front brake pads (and, for
Bulb monitor
37

 Please refuel
When this symbol  comes on for the first time, there are about
8 litres of fuel left in the tank. You should fill up as soon as possible
⇒ page 252.
If this warning symbol lights up although the fuel tank is sufficiently
filled, there is a malfunction in the fuel tank system. The display will
also show the driver message Tank system malfunction ! Contact
workshop. Please contact a qualified workshop.
If the symbol  lights up, this means that one of the turn signals
(front or rear), headlights, brake lights, rear lights, fog lights or the
rear fog light is not working.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 38 Donnerstag, 26. Juli 2007 9:16 09
38
Driver information system
If the  symbol lights up in conjunction with this driver message,
please check the engine oil level as soon as possible ⇒ page 258.
Top up the oil at the next opportunity ⇒ page 259.
Applies to vehicles: with battery power warning system
Battery power

If battery power drops to a level at which you may encounter problems when starting the engine, the display will show the symbol 
and the driver message Low battery charge: Battery will be charged
while driving.
Please bear in mind that the starting ability of the engine may be
impaired while this message is shown.
Message comes on and goes out again
If the message appears in the display after the ignition is switched
on or while driving, and goes out again after a period of time, the
battery has been charged up again sufficiently while the vehicle was
being driven.

 Oil level ! Sensor defective
If the  symbol lights up, take the vehicle to a qualified workshop
and have the oil level sensor checked. Until then it is advisable to
check the oil level every time you fill up with fuel ⇒ page 258.
Applies to vehicles: with diesel engine and diesel particulate filter
Diesel particulate filter obstructed

 Particle filter. See Owner's Manual
Message comes on and does not go out
If the message appears in the display after the ignition is switched
on or while driving, and does not go out again, the battery is not
being maintained at the proper power level. Starting reliability may
be impaired. You should have the battery checked by a qualified
workshop as soon as possible.
Engine oil level (without dipstick)
Engine oil sensor defective

 Add oil, max. 1L. You may continue driving.
If the  symbol lights up in conjunction with this driver message,
add not more than 1 litre of oil at the next opportunity
⇒ page 259.
When the symbol  lights up you can assist the self-cleaning function of the filter by driving accordingly. You should drive at a speed
of at least 60 km/h (engine speed about 2,000 rpm) for about
15 minutes in 4th or 5th gear, or with the selector lever in position S
on vehicles with automatic gearbox*. As a result of the increase in
temperature the soot in the filter will be burned off. The symbol will
disappear once the cleaning process has been completed successfully.
If the symbol  does not go out, please contact a qualified workshop and have the fault rectified.
For further information on the diesel particulate filter ⇒ page 229.
WARNING
Check engine oil level (with dipstick)
 Please check oil level

It is essential that you adjust your speed to suit the weather, road,
terrain and traffic conditions. The recommended driving speed
must never lead to the driver disregarding the traffic regulations.
document_0900452a81b1b9de.book Seite 39 Donnerstag, 26. Juli 2007 9:16 09
Driver information system
Windscreen wipers defective
Applies to vehicles: with dynamic headlight range control
Headlight range control defective

 Headlight range control defective
This symbol  indicates a malfunction in the dynamic headlight
range control. Take the vehicle to a qualified workshop to have the
dynamic headlight range control function repaired.
39

 Windscreen wipers defective
This symbol  indicates a malfunction in the electronics for the
windscreen wipers. Take the vehicle to a qualified workshop to have
the windscreen wiper system repaired.
Tyre pressure monitoring system
Applies to vehicles: with adaptive light
adaptive light defective

Applies to vehicles: with tyre pressure monitoring
 adaptive light defective
This symbol  indicates that the adaptive light is defective. Take
the vehicle to a qualified workshop to have the headlights and/or
the control unit for the adaptive light repaired.
Ignition lock defective
Tyre pressure monitoring display appears
The tyre pressure monitoring display in the instrument
cluster informs the driver if the tyre pressure is too low or
a system malfunction has occurred.

 Ignition lock defective
If the symbol  lights up in the display, there is a malfunction in
the electronic ignition lock. Take the vehicle to a qualified workshop
to have the problem remedied.
Fig. 27 Display:
Warning message with
symbol and text
Applies to vehicles: with Audi drive select
Suspension control

This warning lamp monitors the damping effect of the
shock absorbers.
 Suspension: system fault
If the  symbol lights up in the display, there is a malfunction in the
vehicle suspension. Take the vehicle to a qualified workshop to have
the problem remedied.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 40 Donnerstag, 26. Juli 2007 9:16 09
40
Driver information system
TPMS (Tyre Pressure Monitoring System) Tyre pressure ! System
malfunction ⇒ page 40, fig. 28 will also be displayed in the instrument cluster. Please contact the nearest qualified workshop as soon
as possible.
WARNING
Fig. 28 Display:
System fault ("Systemstörung")
The tyre pressure monitoring system makes use of the ABS sensors
to compare the rolling circumference and the vibration of the
wheels. The display in the instrument cluster alerts the driver if
changes are detected on one or more wheels. If only one tyre is
affected, the display will indicate its position ⇒ fig. 27.
Each time you change a tyre or the tyre pressures on your vehicle,
you must store the new tyre pressures via the sound system or
MMI* ⇒ page 41.
The rolling circumference and vibration can change if:
•
•
•
The tyre pressure is too low
The tyre has suffered structural damage
The air pressure in one or more tyres was changed and the new
tyre pressures were not stored ⇒ page 41, “Storing the tyre pressures”
•
The wheels were changed and the new tyre pressures were not
stored ⇒ page 41, “Storing the tyre pressures”
•
There is a greater load on the wheels of one axle (e.g. if you are
carrying more passengers or luggage)
•
The road surface under the left wheels is different to the road
surface under the right wheels for a long period
Warning lamp
 / TPMS Tyre pressure ! System malfunction
If the warning lamp  flashes for about a minute and then remains
lit after you switch on the ignition, there is a fault in the system.
•
If the tyre pressure warning lamp appears in the instrument
cluster display, slow down immediately and avoid any severe
braking or steering manoeuvres. As soon as you can do so safely,
stop and check the tyres and the tyre pressures.
•
It is the driver's responsibility to ensure that the tyre pressures
are correct. For this reason you must check the tyre pressures
regularly.
•
Under certain conditions (e.g. driving at high speeds, on ice and
snow or on poor road surfaces) the tyre pressure warning lamp
may not light up immediately or not at all.
•
Please ask your Audi dealer or qualified workshop whether run
flat tyres can be used on your vehicle. Unauthorised use of these
tyres can invalidate the vehicle's type approval for use on public
roads. Furthermore, this could cause damage to your vehicle and
possibly also result in an accident.
document_0900452a81b1b9de.book Seite 41 Donnerstag, 26. Juli 2007 9:16 09
Driver information system
41
Applies to vehicles: with tyre pressure monitoring
Storing the tyre pressures
When you change a tyre or the tyre pressure on your
vehicle, you must store the new tyre pressure via the
sound system or MMI*.
Fig. 29 Display:
Storing tyre pressures
– Switch on the ignition.
– Select: Function selector button CAR > Tyre pressure
monitoring > Store tyre pressures.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 42 Donnerstag, 26. Juli 2007 9:16 09
42
Doors and windows
Doors and windows
Central locking system
handles on the inside are deactivated. This makes it more difficult
to break into the vehicle.
Description
Anti-theft alarm system*
The vehicle can be locked and unlocked via the central locking
system. You can use any of the following:
•
•
•
•
Remote control key ⇒ page 47
Door handles in conjunction with advanced key* ⇒ page 47
Lock on driver's door ⇒ page 48
Interior central locking switch ⇒ page 49
Unlocking one side of the vehicle only
When you lock the vehicle, the central locking system will lock the
doors and the boot lid. When you unlock the vehicle, the central
locking system will unlock either the driver's door only, or all the
locks on the vehicle, depending on the setting you have selected on
the sound system or MMI* ⇒ page 50.
If the anti-theft alarm system senses interference with the vehicle it
triggers an audible and visible alarm.
The anti-theft alarm system switches on automatically when the
vehicle is locked. It switches off automatically if you unlock the
vehicle using the remote control.
If you unlock the vehicle by inserting the key in the driver's door, the
ignition must be switched on within 15 seconds, otherwise the
alarm will be triggered. On some export versions, the alarm is triggered immediately when you open a door.
To deactivate the alarm, press the unlock button on the remote
control key or switch on the ignition. The alarm will also switch itself
off when it comes to the end of its cycle.
Switch off the interior monitor and tow-away protection if you wish
to prevent the alarm from being triggered accidentally ⇒ page 50.
Automatic locking function (Auto Lock)
The Auto Lock function locks the doors and the boot lid when the
vehicle exceeds a speed of about 15 km/h.
The vehicle is unlocked again when the ignition key is removed.
Alternatively, the vehicle can also be unlocked via the central
locking switch or by pulling one of the inside door handles. The Auto
Lock function can be switched on and off on the sound system or
MMI* ⇒ page 50.
Turn signals
The turn signals will flash twice when the vehicle is unlocked and
once when the vehicle is locked. If the turn signals do not flash, one
of the doors, the bonnet or the boot lid is still open.
Accidental lock-out
The central locking system prevents you from being locked out of
the vehicle in the following situations:
In the event of an accident in which the airbags inflate, the doors
will be automatically unlocked to facilitate access and assistance.
•
Deadlock mechanism
•
The central locking system is combined with a deadlock mechanism. Once the vehicle has been locked from the outside, the door
When the driver's door is open, it cannot be locked together with
the other doors by pressing the central locking switch and then
closing the door ⇒ page 49.
On vehicles with advanced key*, the boot lid will be released
again automatically if the remote control key that was last in use is
left inside the boot when the boot lid is closed ⇒ page 51.
document_0900452a81b1b9de.book Seite 43 Donnerstag, 26. Juli 2007 9:16 09
Doors and windows
To prevent yourself from being locked out, do not lock the vehicle
with the remote control key before closing the doors or boot lid. If
you accidentally press the locking button on your remote control
key when any of the doors (except for the driver's door) are open,
then put the key down inside the car and forget to take it with you
when you close the doors, you can still open the doors for about one
minute before the vehicle is locked.
43
Set of keys
WARNING
Do not leave anyone (especially children) in the car if it is locked
from the outside and the deadlock mechanism is activated: the
doors and windows cannot then be opened from the inside.
Locked doors could delay assistance in an emergency, potentially
putting lives at risk.
•
Note
Fig. 30 Keys supplied
with the vehicle
A Remote control key
A
The remote control key will lock and unlock the car and start the
engine.
B Spare key
A
Never leave any valuable items in the vehicle unattended. Even a
locked vehicle is not a safe.
•
If the diode on the driver's window sill lights up for about
30 seconds when the vehicle is locked, the central locking system or
anti-theft alarm* is not working properly. Please have the malfunction repaired by an Audi dealer or qualified workshop.
•
The interior monitor of the anti-theft alarm* system will only
function as intended if the windows and the tilting panorama roof*
are closed.
The spare key is intended for temporary use only and should be
used only in an emergency. Keep it in a safe place and do not carry
it on the keyring.
Replacing a key
If you should lose a key, please contact an Audi dealer. Have the
remote control coding for that key deactivated. For this purpose you
should bring all available keys with you. It is also important to notify
your insurance company if a key has been lost.
Electronic immobiliser
The immobiliser is designed to prevent unauthorised persons from
driving the vehicle. If an uncoded key is used, SAFE will appear in
the mileage recorder display.
It may not be possible to start the engine with the key if there is
another ignition key from a different make of vehicle on the same
key ring.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 44 Donnerstag, 26. Juli 2007 9:16 09
44
Doors and windows
Data stored on remote control key
Data related to the service and maintenance of the vehicle are
stored continuously on your remote control key. Your Audi dealer
can read out the data and will then be able to tell you what service
work is required. This also applies to vehicles with advanced key.
Note
The function of the remote control key may be impaired by interference from other nearby radio signals (for example from a mobile
telephone or TV transmitter) if these are in the same frequency
range.
Personal convenience settings
If two people use the same car regularly, it is a good idea for each
person to have his or her “own” remote control key. When you
switch off the ignition or lock the vehicle, your personal settings for
the following convenience features are stored and assigned to the
remote control key:
•
•
•
•
•
•
•
Indicator lamp on remote control key
The indicator lamp on the remote control key lights up
when you press the buttons.
Air conditioner
Central locking system
Windows
parking system*
adaptive cruise control*
Audi drive select*
Seat memory*
The stored settings are then recalled automatically the next time the
vehicle is unlocked, the doors are opened or the ignition is switched
on.
WARNING
•
Always take the key with you when leaving the vehicle - even if
you only intend to be gone for a short time. This is especially
important if children are left in the car. They might otherwise be
able to start the engine or use power-operated equipment such as
the electric windows - this could lead to injuries.
• Wait for the vehicle to come to a standstill before removing the
ignition key from the lock. Otherwise the steering lock could
engage suddenly, causing an accident.
Fig. 31 Indicator lamp
on remote control key
The indicator lamp should light up once briefly when you press one
of the buttons briefly. The indicator lamp should flash when you
press and hold one of the buttons (convenience open/close).
If the indicator lamp does not light up, this means the battery is
exhausted and must be replaced ⇒ page 45. The instrument cluster
display also shows the symbol  and the following message if the
battery is exhausted:
Please change key battery
document_0900452a81b1b9de.book Seite 45 Donnerstag, 26. Juli 2007 9:16 09
Doors and windows
Replacing the battery for the remote control
key
45
– Insert the emergency key.
For the sake of the environment
Used batteries must be disposed of appropriately and must not be
discarded with ordinary household waste.
Note
The new battery must be of the same type as the original one
(CR 2032).
Fig. 32 Remote control
key: Removing the
emergency key
Removing the emergency key
Fig. 33 Remote control
key: Removing the
battery carrier
A ⇒ fig. 32.
A
B out of the remote control key.
Pull the emergency key A
A ⇒ fig. 33 on the battery carrier
Press the release catch A
Fig. 34 Remote control
key: Removing the
emergency key
– Press the release button
– Press the release button
–
–
–
and at the same time pull the battery carrier out of the
remote control key in the direction of the arrow.
– Insert the new CR 2032 battery with the “+” symbol
facing downwards.
– Slide the battery carrier carefully into the remote control
key.
Controls
Safety
Driving tips
A ⇒ fig. 34.
A
B out of the remote control key.
Pull the emergency key A
You can use the emergency key to ...
•
activate and deactivate* the front passenger's airbag
⇒ page 208.
•
•
•
lock and unlock* the glove box ⇒ page 90.
lock and unlock the lockable rear seat.
manually lock and unlock the vehicle if this is not possible using
the remote control key ⇒ page 48.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 46 Donnerstag, 26. Juli 2007 9:16 09
46
Doors and windows
Emergency release for ignition key
Starting the vehicle with the spare key
In the event of a malfunction in the vehicle's electrical
system, it may no longer be possible to remove the ignition key.
Fig. 36 Glove box:
Adapter for spare key
Fig. 35 Ignition lock
with key
If you are not able to remove the ignition key because the
vehicle battery has discharged (for example), remove the
key as follows:
A ⇒ fig. 35 using a ball-point
– Press the release catch A
B out
pen or a similar object and pull the emergency key A
of the remote control key.
– Use the emergency key to lock the vehicle ⇒ page 48.
– Have the vehicle's electrical system checked by a qualified workshop.
Fig. 37 Inserting the
spare key into the
adapter
– Take the adapter for the spare key out of the glove box
⇒ fig. 36.
– Slide the spare key ⇒ fig. 37 all the way into the adapter.
Make sure that the Audi rings are facing upwards.
– Press the spare key in the adapter downwards until you
hear it engage.
– Insert the adapter, spare key first, into the ignition lock.
You should now be able to start the engine in the usual
way.
document_0900452a81b1b9de.book Seite 47 Donnerstag, 26. Juli 2007 9:16 09
Doors and windows
Locking and unlocking the vehicle with the
remote control key
47
WARNING (continued)
doors and windows cannot then be opened from the inside.
Locked doors could delay assistance in an emergency, potentially
putting lives at risk.
Note
Do not use the remote control key when the vehicle is out of sight.
Applies to vehicles: with advanced key
Fig. 38 Remote control
key: Control buttons
– Press the  button to unlock the vehicle ⇒ fig. 38.
– Press the  button to lock the vehicle ⇒
.
Locking and unlocking the vehicle with the
advanced key
The doors and the boot lid can be locked and unlocked
without handling the remote control key.
– Press the  button briefly to unlock the boot lid.
– Press the  button for at least one second to open the
boot lid.
The vehicle will be locked again automatically if you do not open
one of the doors, the boot lid or the bonnet within 60 seconds after
unlocking the car. This function prevents the vehicle from remaining
unlocked if the unlocking button is pressed by mistake.
Fig. 39 Audi advanced
key: Unlocking one of
the doors
The system will either unlock all the doors or certain doors only,
depending on the settings you have chosen on the sound system or
MMI* ⇒ page 50.
Unlocking the vehicle
On vehicles with the advanced key* the selector lever must be in P,
otherwise it will not be possible to lock the vehicle.
– Take hold of the door handle. The door will be unlocked
automatically.
– Pull the door handle to open the door.
WARNING
Do not leave anyone (especially children) in the car if it is locked
from the outside and the deadlock mechanism is activated: the
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 48 Donnerstag, 26. Juli 2007 9:16 09
48
Doors and windows
Locking the vehicle
– Move the selector lever to position P (automatic
gearbox), otherwise it will not be possible to lock the
vehicle.
– Touch the sensor on the door handle once to lock the
vehicle ⇒
.
– Touch the sensor a second time within 2 seconds to lock
the vehicle without activating the deadlock mechanism.
The vehicle can be locked and unlocked from any of the doors. The
driver's door will always be unlocked as well when the passenger's
door is unlocked. The remote control key has to be within a range of
about 1.5 metres of the relevant door or the boot lid. It does not
matter where you carry the key, for instance whether it is in your
jacket pocket or in a briefcase.
The unlocking function may be affected if the sensor area on the
door handle is touched while the vehicle is being unlocked.
The locking function may be affected if you grasp the door handle
while the vehicle is being locked.
Note
Please note the following points if the vehicle is left parked for long
periods:
•
To save electrical power, the proximity sensors are switched off
after a few days. You will then need to pull the door handle once to
unlock the vehicle, and a second time to open it.
•
To prevent the battery from becoming discharged and thus
maintain the vehicle's starting ability for as long as possible, the
power management system will gradually switch off convenience
functions that are not required. In this case you may not be able to
unlock the vehicle with this convenience function.
Locking and unlocking the vehicle using the
key
If the central locking system should fail to work, you can
still lock and unlock the driver's door by turning the emergency key or spare key in the lock.
Once the doors have been locked, they cannot be opened again
immediately. This will enable you to check that the doors are properly closed.
The system will either unlock all the doors or one door only,
depending on the settings you have chosen on the sound system or
MMI* ⇒ page 50.
Fig. 40 Lock on
driver's door
WARNING
Do not leave anyone (especially children) in the car if it is locked
from the outside and the deadlock mechanism is activated: the
doors and windows cannot then be opened from the inside.
Locked doors could delay assistance in an emergency, potentially
putting lives at risk.
Unlocking
– Turn the key to position
vehicle.
A ⇒ fig. 40 to unlock the
A
document_0900452a81b1b9de.book Seite 49 Donnerstag, 26. Juli 2007 9:16 09
Doors and windows
49
Central locking switch
Locking
– Move the selector lever to position P (automatic
gearbox).
B ⇒
– Turn the key once to position A
to lock the vehicle.
B a second time within
– If you turn the key to position A
2 seconds, this will lock the vehicle without activating
the deadlock mechanism.
In order to switch off the anti-theft alarm*, you must switch on the
ignition within 15 seconds after opening the driver's door. Otherwise the alarm will be triggered.
If the central locking system should fail to work at any time, the
passenger's door can be locked manually ⇒ page 51.
WARNING
Do not leave anyone (especially children) in the car if it is locked
from the outside and the deadlock mechanism is activated: the
doors and windows cannot then be opened from the inside.
Locked doors could delay assistance in an emergency, potentially
putting lives at risk.
Fig. 41 Driver's door:
Central locking switch
– Press the  button to unlock the vehicle ⇒ fig. 41.
– Press the  button to lock the vehicle ⇒
.
Please note the following when you use the central locking switch
to lock your vehicle:
•
The doors and the boot lid cannot be opened from the outside
(for safety reasons, when stopped at traffic lights, etc.).
•
The LED in the central locking switch lights up when both of the
doors and the boot lid are closed and locked.
•
•
You can open the doors individually from the inside by pulling
the inside door handle.
Note
The central locking switch and the release button for the boot lid
 will function after the ignition is switched on.
•
If the vehicle is locked with the key when the central locking
system is operational, it is only possible to unlock all the doors and
the boot lid centrally with the key within the next 45 seconds. After
this period, the key will only unlock the driver's door.
•
In the event of an accident in which the airbags inflate, doors
locked from the inside will be automatically unlocked to facilitate
access and assistance.
WARNING
•
The central locking switch is still operative when the ignition is
switched off and will automatically lock the entire vehicle when
pressed.
•
The central locking switch inside the vehicle is not operative if
you lock the vehicle from the outside.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 50 Donnerstag, 26. Juli 2007 9:16 09
50
Doors and windows
You can still unlock all doors and the luggage compartment. To do
so, press the unlock button twice on the remote control key.
WARNING (continued)
•
Locked doors could delay assistance in an emergency, potentially putting lives at risk. Do not leave anyone (especially children)
in the vehicle.
Note
The doors and the boot lid are locked automatically when the
vehicle reaches a speed of about 15 km/h (Auto Lock) ⇒ page 42.
You can unlock the vehicle again via the central locking switch.
Setting the central locking system
You can use the sound system or MMI* to select which
doors are unlocked by the central locking system.
Fig. 42 Display:
Central locking menu
– Select: Function selector button CAR > Central locking
> Unlocking single door.
In the Unlocking single door menu you can specify which doors you
wish to have unlocked when you unlock the vehicle using the
remote control key or the advanced key*. If you switch the
Unlocking single door function on, only the driver's door will be
unlocked when you press the unlocking button on the remote
control key once.
When you lock the vehicle, the central locking system will automatically lock all the doors and the boot lid together.
If you select “Locking boot lid/tailgate” on, you can no longer open
the luggage compartment using the handle on the boot lid
⇒ page 52, fig. 46. In this case, you can open the boot lid using the
 button on the remote control key ⇒ page 47, fig. 38 or the unlock
switch on the driver's door ⇒ page 51, fig. 45.
If you select “Retract mirrors” on, the exterior mirrors will be
retracted automatically ⇒ page 70 when you press the lock button
 on the remote control key.
Applies to vehicles: with anti-theft alarm system
Deactivating the interior monitor and towaway protection
Fig. 43 Front end of
the driver's door:
Switches for interior
monitor and tow-away
protection
When the vehicle is locked, the alarm will be triggered if
movements are detected in the interior (e.g. by animals) or
if the vehicle's inclination is changed (e.g. during transport).
You can prevent the alarm from being triggered accidentally
by switching off the interior monitor and/or tow-away
protection.
document_0900452a81b1b9de.book Seite 51 Donnerstag, 26. Juli 2007 9:16 09
Doors and windows
Deactivating interior monitor
– Press switch A ⇒ page 50, fig. 43. The diode in the
switch will light up.
A mechanical locking device (only visible when the doors
are open) is provided on the front passenger's door and the
rear doors.
Deactivating tow-away protection
– Take the emergency key out of the remote control key
⇒ page 45.
A
– Press switch
B . The diode in the switch will light up.
A
The interior monitor and tow-away protection will be switched on
again automatically the next time the vehicle is locked.
WARNING
Do not leave anyone (especially children) in the car if it is locked
from the outside and the deadlock mechanism is activated: the
doors and windows cannot then be opened from the inside.
Locked doors could delay assistance in an emergency, potentially
putting lives at risk.
Locking the doors manually if the central
locking fails to work
51
– Pull the cap out of the opening ⇒ fig. 44.
– Insert the key in the slot inside and turn it as far as the
stop to the right (if the door is on the right side) or to the
left (if the door is on the left side).
Once the door has been closed it can no longer be opened from the
outside. The door can be opened from the inside by pulling the door
handle. If the child-proof catch is engaged on one of the rear doors,
the door can be opened by pulling the inside door handle once and
then opening the door from the outside.
Boot lid
Opening and closing the boot lid
If the central locking system should fail to work at any
time, each door will have to be locked separately.
Fig. 45 Driver's door:
Unlocking the boot lid
Fig. 44 Door: Locking
the door manually
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 52 Donnerstag, 26. Juli 2007 9:16 09
52
Doors and windows
Note
When the vehicle is locked, you can unlock the boot lid separately
by pressing the  button on the remote control key. The boot lid
will lock automatically when you close it again.
Manual release of the boot lid
Fig. 46 Release catch
on the boot lid
The boot lid can be released manually from the inside.
Opening boot lid
– Press the  button on the remote control key for at least
one second, or
– Pull the unlock switch  on the driver's door ⇒ page 51,
fig. 45, or
– Press the release catch on the boot lid ⇒ fig. 46.
– The boot lid is unlocked and opens automatically.
– Push the boot lid up slightly to secure it in the open position.
Closing boot lid
– Pull down the boot lid by the handle on the inside and let
it drop into the latch ⇒
.
WARNING
•
After closing the boot lid, always check that the catch has
engaged properly. The boot lid could otherwise open suddenly
when the vehicle is moving - this could result in an accident.
•
The boot lid must always be completely closed when the
vehicle is moving, otherwise toxic exhaust fumes can be drawn
into the interior.
Fig. 47 Luggage
compartment: Access
to manual release
– Prise off the cover (using the emergency key) ⇒ fig. 47.
– Press the sliding lever in the direction of the arrow to
unlock the boot lid.
document_0900452a81b1b9de.book Seite 53 Donnerstag, 26. Juli 2007 9:16 09
Doors and windows
Child-proof catches
Electric windows
Child-proof catches on the rear doors
Controls
The child-proof catches prevent the rear doors being
opened from the inside.
The driver can operate all the electric windows.
53
Fig. 49 Detail of the
driver's door: Controls
Fig. 48 Child-proof
catches on the rear
doors
All electric windows have two-stage switches:
The rear doors are equipped with child-proof catches. The
child-proof catches are only visible with the doors open.
Take the emergency key out of the remote control key
⇒ page 45.
Engaging the child-proof catch
– Turn the key in the direction of the arrow ⇒ fig. 48.
Opening the windows
– Press the switch as far as the first stop and hold it until
the window has moved to the desired position.
– Press the switch briefly to the second stop: the window
will automatically open all the way.
Closing the windows
Disengaging the child-proof catch
– Turn the key in the opposite direction of the arrow.
– Pull the switch as far as the first stop and hold it until the
window has moved to the desired position.
When the child-proof catch is engaged, the inside door handle will
not function, and the door can only be opened from the outside.
– Pull the switch briefly to the second stop: the window will
automatically close all the way.
Switches for electric windows
A Driver's door
A
B Front passenger's door
A
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 54 Donnerstag, 26. Juli 2007 9:16 09
54
Doors and windows
C Rear door (left-side)*
A
D Rear door (right-side)*
A
S Safety switch
A
Child safety switch
S ⇒ page 53, fig. 49 is pressed in, the
When the safety switch A
symbol  in the switch lights up. The window switches in the rear
doors are deactivated.
Convenience open/close function
The convenience open/close function allows you to open
and close the windows and the sun roof* with the remote
control key.
You can select which windows are opened in the settings on
the sound system or MMI* ⇒ page 55.
Convenience open function
WARNING
•
Always take the key with you when leaving the vehicle - even if
you only intend to be gone for a short time. This is especially
important if children are left in the car. They might otherwise be
able to start the engine or use power-operated equipment such as
the electric windows - this could lead to injuries. The window
switches are only deactivated when the driver's door or the front
passenger's door is opened.
•
Always be careful when closing the windows. Careless use of
the electric windows can cause severe injuries.
•
When locking the vehicle from the outside, make sure that
nobody is inside the vehicle, as the windows cannot be opened
from the inside in an emergency.
– Press and hold the unlocking button  on the remote
control key until the windows have reached the desired
position and the sun roof* is open.
Convenience close function
– Press and hold the locking button  on the remote
control key until the windows and the sun roof* are
closed ⇒
.
Convenience close function with advanced key*
– Touch and keep your hand in contact with the locking
sensor on the door handle until the windows and the sun
roof* are closed.
Note
The windows can be operated for about ten minutes after the ignition has been switched off. The window switches are only deactivated when the driver's door or the front passenger's door is
opened.
WARNING
•
Take care when closing the windows and the sun roof*. Careless or uncontrolled use can cause injuries.
•
For safety reasons, you should only use the remote control
open and close functions within about 2 metres of the vehicle. To
avoid injuries, always keep an eye on the windows when pressing
the button to close them. The windows and sun roof stop moving
as soon as the button is released.
document_0900452a81b1b9de.book Seite 55 Donnerstag, 26. Juli 2007 9:16 09
Doors and windows
Settings for convenience open function
Sun roof
The driver can use the sound system or MMI* to select
which windows are opened.
Controls
Fig. 51 Detail of headliner: Rotary control for
sun roof
Fig. 50 Display:
Convenience open
menu
– Select: Function selector button CAR > Windows >
Convenience open.
If you wish to use the convenience open function for the windows
and the sun roof*, select on for the functions Front doors, Rear
doors and Sun roof*.
Tilting open
– You can tilt the sun roof open or closed only when the
0 position ⇒ fig. 51.
switch is in the A
– Press the switch briefly to tilt open the sun roof.
– Pull the switch briefly to close the sun roof again ⇒
The one-touch open and close function must be reactivated if the battery has been disconnected.
– Pull and hold the electric window switch until the
window is fully closed.
– Release the switch and then pull it again for at least one
second.
Sliding open
– To slide the sun roof open to the position for low wind
1 (until you feel a
noise, turn the switch to position A
resistance).
– To slide the sun roof fully open, turn the switch past the
2 and hold the switch.
point of resistance to position A
– To close the sun roof, turn the switch to position
⇒
.
Safety
.
– To set an intermediate position, press or pull the switch
until the sun roof has reached the desired position.
What to do after a malfunction
Controls
55
Driving tips
General maintenance
Self-help
0
A
Technical data
document_0900452a81b1b9de.book Seite 56 Donnerstag, 26. Juli 2007 9:16 09
56
Doors and windows
– You can set the roof to an intermediate position by
turning the switch to the desired position.
Closing the sun roof manually
The sun roof can be operated for about ten minutes after the ignition has been switched off. The switch is deactivated immediately
when one of the front doors is opened.
Sliding sun blind with glass sun roof*
The sliding sun blind can be opened and closed manually in any
position. The sun blind opens automatically when you slide open
the sun roof. When the sun roof is raised to the tilt position, the rear
end of the sun blind is raised together with the sun roof.
Fig. 52 Detail of headliner: Unscrewing the
light housing
WARNING
Take care when closing the sun roof. Careless or uncontrolled use
of the sun roof can cause injuries. For this reason, always take out
the ignition key when leaving the vehicle.
Caution
Fig. 53 Detail of headliner: Crank for manual
operation
You should always close the sun roof when leaving the car. Sudden
rain could seriously damage your car's interior equipment, especially the on-board electronic systems.
•
Note
Should you not be able to close the tilted sun roof, pull and hold
the switch until the sun roof is closed.
•
Details on the convenience open/close function ⇒ page 54.
– Open the compartment for (sun)glasses. The screw
⇒ fig. 52 will then be visible.
– Remove the screw and detach the light unit.
– Insert the crank all the way into the hexagonal socket
⇒ fig. 53 and turn. The sun roof will now close.
Note
To make it easier to turn the crank, you can make use of the screwdriver handle (tool kit).
document_0900452a81b1b9de.book Seite 57 Donnerstag, 26. Juli 2007 9:16 09
Lights and vision
57
Lights and vision
Lights
Automatic headlight control (AUTO)*
Switching lights on and off
When the switch is set to AUTO, the headlights switch on automatically according to the ambient light conditions, for instance in a
tunnel, at sunset, or in the rain or snow. The  symbol lights up
when the dipped headlights are on. The headlights are switched on,
regardless of the light conditions, when you switch on the fog
lights.

The headlights are switched off automatically when you switch off
the ignition.
On vehicles with a rain sensor, the headlights switch on automatically after several windscreen wiper cycles. The instrument lighting
does not switch on, however.
Fig. 54 Dashboard:
Light switch
Switching on automatic headlights* (AUTO)
– Turn the light switch to AUTO ⇒ fig. 54.
Switching on the side lights
– Turn the light switch to position .
Malfunction of light sensor
Switching on dipped headlights
If a malfunction should occur in the light sensor, the instrument
cluster will show the message:
– Turn the light switch to position .
 Automatic headlights / automatic wipers defective
Switching off the lights
– Turn the light switch to position O.
The dipped beam headlights will only work with the ignition on.
The symbol  next to the light switch will light up when the side
lights or headlights are on.
Controls
While using the automatic headlights you can activate the main
beam headlights as normal if this function has been activated in the
MMI. However, if you switch on the main beam headlights while
using the AUTO function and then do not switch back to the dipped
headlights setting, only the dipped headlights will come on the next
time you switch on the AUTO function. To be able to use the main
beam headlights again you must first pull the main beam lever back
to the "off" position and then push it forward to "on".
Safety
Driving tips
For safety reasons, the dipped beam headlights will then be
switched on permanently when the light switch is set to the AUTO
position. However, you can still switch the lights on and off in the
normal way with the light switch. You should have the light sensor
checked by a qualified workshop as soon as possible.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 58 Donnerstag, 26. Juli 2007 9:16 09
58
Lights and vision
1 ⇒ fig. 55 to switch on the front fog lights
– Press button A
.
WARNING
The automatic headlights are only intended to assist the driver.
The driver must always ensure that the headlights are used when
required, and may have to switch them on manually when the light
conditions or visibility are poor. For example, the light sensors are
not able to detect fog. Therefore, you should always switch on the
headlights  in these conditions and when driving after dark.
•
– Press button
2 to switch on the rear fog lights .
A
Front fog lights
The side lights or headlights must be switched on. The green diode
at the edge of the switch lights up when the front fog lights are
switched on.
When the headlights are set to AUTO, the dipped headlights are
switched on automatically when you switch on the front fog lights.
Note
The light sensor for automatic headlight control is located in the
mounting for the interior mirror. Do not affix any stickers on this
section of the windscreen to avoid malfunctioning of the sensor.
•
Some of the settings for the exterior lighting can be adjusted
⇒ page 59.
•
If the lights are left on after the key has been taken out of the
ignition lock, a buzzer sounds when the driver's door is opened.
•
The use of the lighting described here is subject to the relevant
statutory requirements.
•
The coming home/leaving home function is active only when the
light switch is set to AUTO.
Rear fog lights
The headlights or side lights and the front fog lights must be
switched on.
The yellow diode at the edge of the switch lights up when the rear
fog lights are switched on.
If you are towing a trailer or caravan equipped with a rear fog light
on a vehicle with a factory-fitted towing bracket, only the rear fog
light on the trailer or caravan will light up.
Caution
To avoid dazzling the traffic behind you, the rear fog light should
only be used in accordance with statutory regulations.
Fog lights
Fig. 55 Switch for
front fog lights
document_0900452a81b1b9de.book Seite 59 Donnerstag, 26. Juli 2007 9:16 09
Lights and vision
Exterior lighting settings
59
Daytime running lights*
You can change the settings for these functions on the
sound system or MMI*.
The daytime running lights are switched on and off together with
the ignition.
On vehicles for some markets the daytime running lights cannot be
switched off if the vehicle has halogen headlights.
Headlamp converter* for driving abroad
The asymmetric low beams of the headlights are designed to light
up the near side of the road more intensely. If you drive a right-hand
drive vehicle in a left-hand drive country, or vice versa, you will
dazzle oncoming traffic.
Fig. 56 Display: Exterior lighting
Important: .
Vehicles with xenon headlights*: The headlamp converter should be
switched on to avoid dazzling oncoming traffic.
Vehicles with halogen headlights: Opaque stickers should be
applied to certain parts of the headlight lenses. For further information, please consult an Audi dealer or other qualified workshop.
– Select: Function selector button CAR > Exterior lighting.
coming home
Instrument lighting
The coming home function lights up the area round the vehicle after
dark when the ignition has been switched off and the driver's door
opened. This function can be set to operate for a time interval
between 0 (off) and 60 seconds. The coming home function is operational when the light switch is set to AUTO.
The background lighting of the instruments, the centre
console and the display can be adjusted as required.
leaving home
The leaving home function lights up the area round the vehicle after
dark when the vehicle is unlocked. The function can be switched on
or off as required. The leaving home function is operational when
the light switch is set to AUTO.
Fig. 57 Instrument
lighting
Automatic headlights*
The sensitivity of the light sensor (i.e. how soon the lights are
switched on) can be adjusted.
Controls
Safety
Driving tips
– Briefly press the knob to release it.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 60 Donnerstag, 26. Juli 2007 9:16 09
60
Lights and vision
– Turn the button clockwise +” to increase the brightness
of the instrument lighting in dark conditions.
Applies to vehicles: with headlight range control
– Turn the button anti-clockwise -” to reduce the brightness of the instrument lighting in dark conditions.
When the dipped beam headlights are switched on, the
range of the headlights can be adjusted to suit the load
being carried.
– Press the knob in again to prevent the setting from being
changed unintentionally.
Headlight range control

The instrument lighting (dials and needles), the centre console illumination and the illumination of the displays are regulated by a
light sensor incorporated in the instrument cluster. In bright conditions any changes made to the brightness of the instrument lighting
have no effect.
Fig. 58 Headlight
range control
Note
The instrument lighting (illumination of dials and needles) is
switched on when the ignition is on and the vehicle's lights are off.
The instrument lighting is dimmed automatically as the daylight
starts to fade; it is switched off completely when the light conditions become very poor. This function is intended to remind the
driver to switch on the dipped-beam headlights in good time when
light conditions become poor.
– Turn the thumbwheel  ⇒ fig. 58 to the appropriate
setting.
Adjustment settings
The settings correspond roughly to the following load conditions:
O Two front occupants, luggage compartment empty
A
I
All seats occupied, luggage compartment empty
A
II All seats occupied, luggage compartment loaded
A
III Driver only, luggage compartment loaded
A
Caution
Always adjust the headlights to avoid dazzling oncoming traffic.
Make sure you lower the headlights when the vehicle is carrying a
heavy load.
document_0900452a81b1b9de.book Seite 61 Donnerstag, 26. Juli 2007 9:16 09
Lights and vision
61
Applies to vehicles: with xenon headlight bulbs
Note
Dynamic headlight range control
Headlights with xenon gas-discharge bulbs automatically adapt to
suit the load being carried when the engine is switched on. The
headlights are also automatically adjusted when the vehicle is in
motion (e.g. when accelerating and braking).
The system is active at speeds from approximately 10 km/h to
110 km/h.
Hazard warning lights

The hazard warning lights are used to make other road
users aware of your vehicle in hazardous situations.
Applies to vehicles: with adaptive light
adaptive light
This feature provides better illumination when you drive
through a corner.
Fig. 60 Switch for
hazard warning lights
Fig. 59 adaptive light
when driving
The adaptive light gives better illumination of the bend and the side
of the road when driving through a corner ⇒ fig. 59. The adaptive
light is controlled automatically, depending on the speed of the
vehicle and the steering wheel angle.
The headlights are regulated automatically when you drive through
a corner, depending on how far you turn the steering wheel. To
avoid having a dark spot in front of the vehicle the two headlights
are directed at different angles.
– Press the switch  to switch the hazard warning lights
on or off ⇒ fig. 60.
All four turn signals flash simultaneously when the hazard warning
lights are switched on. The two turn signal indicator lamps   and
the indicator lamp in the switch  will flash at the same time. The
hazard warning lights also work when the ignition is switched off.
The hazard warning lights come on automatically in the event of an
accident in which an airbag is triggered or in the case of an emergency stop (full brake application).
Note
You should switch on the hazard warning lights to warn other road
users, for instance:
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 62 Donnerstag, 26. Juli 2007 9:16 09
62
Lights and vision
•
•
•

When reaching the tail end of a traffic jam
Main beam headlights
If your vehicle breaks down or there is an emergency
– Press the lever forward to switch on the main beams.
If your vehicle is being towed away, or if you are towing another
vehicle.
– Pull the lever back towards you to switch the main beam
headlights off again.

Turn signal and main beam lever
Headlight flasher
The turn signal and main beam lever also operates the
parking lights and the headlight flasher.
– Pull the lever towards the steering wheel to operate the
flasher.
Parking lights

– Switch off the ignition.
– Move the lever up or down to turn on the right or lefthand parking lights respectively.
Notes on these functions
Fig. 61 Turn signal and
main beam headlight
lever
The turn signal and main beam headlight lever has the
following functions:
Turn signals

•
The turn signals only work when the ignition is switched on. The
corresponding indicator lamp  or  flashes in the instrument
cluster.
•
The turn signals are cancelled automatically when the steering
wheel is returned to the straight-ahead position.
•
The main beam headlights can only be switched on if the dipped
beam headlights are already on. The main beam headlight indicator
lamp  then comes on in the instrument cluster.
– Move the lever all the way up to indicate right, or all the
way down to indicate left ⇒ fig. 61.
•
– Move the lever briefly up or down just as far as the point
of resistance and then release it: the turn signals will
flash three times.
•
– Move the lever up or down just as far as the point of
resistance and hold it there: the turn signals flash for as
long as you hold the lever.
The headlight flasher comes on for as long as you pull the lever –
even if no other lights are switched on. The main beam headlight
indicator lamp  then comes on in the instrument cluster.
When the parking lights are switched on, the headlight and the
rear light on one side of the car light up with reduced intensity. The
parking lights will only work with the ignition off. A warning buzzer
will sound for as long as the driver's door is open.
document_0900452a81b1b9de.book Seite 63 Donnerstag, 26. Juli 2007 9:16 09
Lights and vision
Front reading lights
Caution
Do not use the main beam headlights or the headlight flasher if this
would dazzle oncoming traffic.
Interior lights
Front interior lights
The front interior lighting also incorporates the reading
lights for the driver and passenger.
63

B ⇒ fig. 62 to switch the left
– Press one of the switches A
or right reading light on and off.
If you switch on the courtesy lighting, the interior lights come on
automatically when the vehicle is unlocked or the doors are opened.
The light also comes on when the key is pulled out of the ignition. It
goes out approximately 30 seconds after the doors are closed. The
interior light is switched off immediately when the vehicle is locked
or when the ignition is switched on.
If a door is left open, the light is switched off after about 10 minutes
to prevent the battery from running flat.
The brightness of the light is automatically adjusted by a dimmer
when it is switched on.
Rear interior lights
Reading lights are also provided for rear passengers.
Fig. 62 Headliner:
Front interior
lighting/reading lights
A ⇒ fig. 62 for the interior light has the
The rocker switch A
following functions:
Courtesy light position
– Move switch
A to the centre position.
A
Fig. 63 Headliner: Rear
reading lights
Interior light switched on
– Move switch
The reading lights are switched on and off with the switches .
A to position I.
A
Interior light switched off
– Move switch
Controls
A to position O.
A
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 64 Donnerstag, 26. Juli 2007 9:16 09
64
Lights and vision
Clear vision
Applies to vehicles: with sun blinds
Sun visors
Sun blinds are provided for the rear window and the rear
side windows.
Sun blinds
The sun visors can improve visibility and contribute to
safety.
Fig. 65 Switch for sun
blind (vehicles with
MMI)
Fig. 64 Passenger's
side: Sun visor
The sun visors for the driver and the front passenger can be pulled
out of their mountings in the centre of the vehicle and turned
1 . Once the sun visor has been turned
towards the doors ⇒ fig. 64 A
towards the door you can pull it towards the rear as desired.
Make-up mirrors
There are covers on the make-up mirrors in the sun visors. The light
for the mirror (located in the headlining) comes on automatically
2 is slid open. The light switches itself off
when the mirror cover A
when the cover is closed and when the sun visor is pushed back
up.
Fig. 66 Switch for sun
blind
Sun blinds (rear side windows)
– Pull out the blind and hook it into the retainers at the top
of the door frame.
Sun blind (rear window)
– Press the switch  ⇒ fig. 65 or ⇒ fig. 66 to extend or
retract the sun blind for the rear window.
document_0900452a81b1b9de.book Seite 65 Donnerstag, 26. Juli 2007 9:16 09
Lights and vision
– To retract the sun blind automatically when reversing,
select: Function selector button CAR > Windows >
Automatic rear blind > on.
Windscreen wipers
If you switch the Automatic rear blind function on in the sound
system or MMI*, the raised sun blind will be retracted automatically
when reverse gear is engaged ⇒ page 55. In this way, the rear blind
will not obstruct your vision when reversing. The rear blind returns
to its raised position when reverse gear is disengaged and the
vehicle is driven forwards at a speed above about 15 km/h. The
current setting is automatically stored and assigned to the remote
control key.
The windscreen wiper lever controls the windscreen
wipers and the automatic wash and wipe.
Windscreen wipers

If the rear blind was rolled in automatically when reversing and then
the ignition was switched off and on again, the blind will not roll
back out again when you select a forward gear and the speed
exceeds 15 km/h. You will then have to press the button  on the
centre console to extend the blind again.
The sun blind for the rear window switches off automatically when
it reaches the end position. It can be made to move in the other
direction before it reaches its end position by briefly pressing the
switch a second time. If the ignition is turned off while the blind is
still moving, it continues until it reaches the end position before
switching off.
•
65
Fig. 67 Windscreen
wiper lever
The windscreen wiper lever has the following settings:
Brief wipe
– Move the lever down to position
screen a brief wipe.
1 to give the windA
 (activating rain sensor)
2 .
– Move the lever up to the stop A
Intermittent wipe
Note
An overload cut-out may be activated if the sun blind is operated
repeatedly. There will then be a short delay before the blind can be
operated again.
•
As the material of the sun blind is less flexible at low temperatures the electric actuator is switched off when the temperature in
the car is below -5°C. The blind can only be operated when the
temperature in the car's interior rises above this level.
A to the left or right to set the sensi– Move the control A
tivity of the rain sensor.
Slow wiper speed
– Move the lever up to the stop
3 .
A
Fast wiper speed
– Move the lever up to the stop
Controls
Safety
Driving tips
General maintenance
4 .
A
Self-help
Technical data
document_0900452a81b1b9de.book Seite 66 Donnerstag, 26. Juli 2007 9:16 09
66
Lights and vision
A
To reduce the sensitivity level of the rain sensor move control A
⇒ page 65, fig. 67 to the left. To increase the sensitivity level of the
rain sensor move the control to the right.
Automatic wash and wipe
– Pull the lever to position
A.
5
– Release the lever again. The washer will stop and the
wipers will keep running for approximately 4 seconds.
The number of wipe cycles varies according to the length
of time the lever is pulled.
If you have selected a high sensitivity level for the rain sensor the
windscreen wipers will react sooner to any moisture on the windscreen. The wiper intervals in the intermittent wipe setting are also
varied automatically according to the road speed (in addition to the
sensitivity setting).
Switching off the wipers
– Move the lever to the "off" position
0 .
A
General notes
The washers and wipers will only work when the ignition is switched
on.
If you stop briefly, e.g. at traffic lights, the wiper speed will automatically be reduced by one level.
The windscreen washer jets are heated when the ignition is
switched on if the outside temperature is low.
Dribble wipe
About 5 seconds after the wash and wipe cycle has finished, the
windscreen wiper system automatically gives the screen one extra
wipe to remove any dribbles of water.
If you want to deactivate the dribble wipe function while driving,
5 again within 10 seconds.
pull the lever to position A
The dribble wipe function will be re-activated the next time the ignition is switched off and on.
Rain sensor*
The rain sensor will only function in the intermittent wipe position.
The intermittent wipe function is activated automatically when it
starts to rain.
Before you reach a road speed of 6 km/h you will have to activate the
rain sensor manually by switching it off and back on again.
WARNING
•
Poor visibility can cause accidents. Always ensure that the
wiper blades are in good condition ⇒ page 68, “Changing wiper
blades”.
•
The rain sensor is only intended to assist the driver. The driver
is still obliged to manually operate the windscreen wipers as
required depending on visibility.
•
Do not use water-repellent coatings on the windscreen. In bad
visibility conditions such as light rain, low sun or when driving at
night these coatings can cause increased dazzle, which is a
serious safety hazard. Such coatings can also cause the wiper
blades to judder.
•
Caution
In icy conditions, always check that the wiper blades are not
frozen to the glass before using the wiper for the first time. If you
switch on the wipers when the wiper blades are frozen to the glass,
this could damage both the wiper blades and the wiper motor.
•
Make sure you switch off the windscreen wiper system (lever in
position "0") before you use an automatic car wash. This will avoid
inadvertent triggering of the wipers and possible damage to the
wiper system.
document_0900452a81b1b9de.book Seite 67 Donnerstag, 26. Juli 2007 9:16 09
Lights and vision
•
67
Service position
Note
Check that the washer fluid reservoir is full before starting a long
journey. Filling the reservoir ⇒ page 267.
Use the service position to change the wiper blades.
•
Worn or dirty wiper blades can cause smearing on the glass
which can also impair the effectiveness of the rain sensor. Please
check the wiper blades regularly.
Applies to vehicles: with headlight washers
Headlight washer system
Fig. 68 Display: Windscreen wipers
The headlight washer system only operates when the lights
are switched on.
5
– Move the automatic wash and wipe lever to position A
⇒ page 65, fig. 67.
The headlight washer system is always activated the first time you
operate the automatic wash and wipe. Subsequently, it is only activated about every five wash and wipe cycles. The headlights are
always washed if you hold the lever for longer than about
2 seconds.
Fig. 69 Service position
The headlight washer jets come out of the bumper automatically
(under water pressure).
Clean off stubborn dirt (insects, etc.) from the lenses at regular
intervals, for instance when stopping for fuel.
You can set the wipers to the service position on the sound
system or MMI*.
To ensure that the system works properly in winter, keep the nozzle
holders free of snow and remove any ice with a de-icer spray.
– If the wiper blades are not frozen to the windscreen,
0
move the windscreen wiper lever to the "off" position A
⇒ page 65, fig. 67.
– Select: Function selector button CAR > Windscreen
wipers > Service position ⇒ fig. 68.
•
on - the wiper blades can only be replaced when the wiper arms
are in the service position ⇒ fig. 69. If you only work on the wipers
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 68 Donnerstag, 26. Juli 2007 9:16 09
68
Lights and vision
when they are in the service position you will also avoid damaging
the paintwork on the bonnet.
•
off - the windscreen wipers will be moved back to their original
position.
– Lift the wiper arm away from the glass.
1 on the wiper blade ⇒ fig. 70.
– Press the release button A
Hold the wiper blade firmly and press it forwards slightly
2 .
A
– Slide the wiper blade upwards
Caution
Never move the vehicle with the front wiper arms in a raised position as they are automatically moved back to their normal park position above a speed of 6 km/h. The paintwork on the bonnet may be
damaged as a result.
3 .
A
Fitting the wiper blade
– Fit the new wiper blade into the mounting on the wiper
4 . You should hear it engage in the wiper arm.
arm A
– Fold the wiper arm back down onto the glass.
•
Note
You can also use the service position, for example, if you want to
fix a cover over the windscreen in the winter to keep it clear of ice.
•
The service position is automatically set to off when you operate
the windscreen wiper lever or the road speed exceeds 6 km/h.
WARNING
•
To prevent smearing on the glass, the wiper blades should be
cleaned regularly using a window cleaner solution. If the wiper
blades are very dirty (insects etc.), they should be cleaned using a
sponge or cloth – bad visibility can cause accidents.
•
Changing wiper blades
Good wiper blades are essential for clear vision.
For safety, the wiper blades should be changed once or twice a
year.
Caution
The windscreen wipers must be in the service position ⇒ page 67
when replacing the blades! Otherwise the wiper motor or the paintwork on the bonnet may be damaged.
Rear-view mirrors
Fig. 70 Removing the
wiper blades
Manual anti-dazzle adjustment
Taking off the wiper blade
Normal setting
– Set the wipers to the service position ⇒ page 67.
– Push the lever at the bottom of the mirror away from you.
document_0900452a81b1b9de.book Seite 69 Donnerstag, 26. Juli 2007 9:16 09
Lights and vision
Anti-dazzle setting
– Pull the lever at the bottom of the mirror towards you.
•
•
69
when the interior lighting is switched on
when reverse gear is engaged
WARNING
Applies to vehicles: with automatic anti-dazzle adjustment for interior mirror
Automatic anti-dazzle adjustment
The automatic anti-dazzle function can be switched on
and off as desired.
Electrolyte fluid can leak from a broken mirror. This fluid can cause
irritation to the skin, eyes, and respiratory organs. Wash thoroughly with clean water should you come into contact with this
fluid. Seek medical assistance if needed.
Caution
Electrolyte fluid leaking from a broken mirror can cause damage to
plastic surfaces. Use a sponge or similar to remove the fluid as soon
as possible.
Fig. 71 Anti-dazzle
interior mirror: On/off
button with indicator
lamp
Switching off anti-dazzle function
– Press button
out.
A ⇒ fig. 71 - the indicator lamp A
B will go
A
Note
If you switch off the anti-dazzle function for the interior mirror,
this will also deactivate the anti-dazzle function for the exterior
mirrors.
•
The automatic anti-dazzle function will only work properly if the
sun blind* for the rear window is not in use and there are no other
objects preventing light from reaching the interior mirror.
•
Do not attach any stickers to the windscreen in front of the
sensors, as these could lead to malfunctioning of the mirror.
Switching on anti-dazzle function
– Press button
•
A - the indicator lamp A
B will light up.
A
Anti-dazzle function
The anti-dazzle function is activated every time the ignition is
switched on. The green indicator lamp lights up in the mirror
housing.
When the anti-dazzle function is activated the interior mirror will
darken automatically according to the amount of light it receives
(for example from the headlights of a vehicle behind). The mirror
will not darken automatically:
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 70 Donnerstag, 26. Juli 2007 9:16 09
70
Lights and vision
Exterior mirrors
Memory for exterior mirrors*
The exterior mirrors are adjusted electrically.
On vehicles with memory function for the driver's seat, the setting
of the exterior mirrors is automatically stored together with the seat
position ⇒ page 75.
Tilting function for exterior mirror on passenger side*
(only if equipped with memory for exterior mirrors)
When reverse gear is engaged, the mirror surface tilts slightly
downwards, provided the mirror control is switched to the exterior
R ⇒ fig. 72). This
mirror on the passenger's side (knob in position A
provides a better view of the kerb when parking.
Fig. 72 Detail of the
armrest: Adjuster knob
Adjusting exterior mirrors
L (left exterior mirror)
– Turn the adjuster knob to position A
R (right exterior mirror) ⇒ fig. 72.
or position A
– Move the knob as required to adjust the exterior mirror
for a good rearward view.
Heated mirrors
– Turn the knob to position
A .
A
Retracting both exterior mirrors*
– Turn the knob to position
B .
A
The mirrors are heated depending on the outside temperature until
the ignition is switched off, even if the knob is no longer in position
A .
A
It may be advisable to retract* the exterior mirrors to protect them
when parking or when driving through tight spaces.
The mirror returns to its original position when reverse gear is
disengaged and the vehicle is driven forwards at a speed above
about 15 km/h. The mirror will also return to its original position
when the adjuster knob is turned to the position for the driver's
L or when the ignition is switched off.
exterior mirror A
If the position of the mirror surface is changed while the mirror is
tilted, this new position is automatically stored and assigned to the
remote control key when you disengage reverse gear.
•
Caution
Convex or wide-angle* exterior mirrors give a larger field of
vision. However, they also make objects appear further away than
they actually are. For this reason, you should not rely on these
mirrors for judging the distance of vehicles behind.
•
If one of the mirror housings is knocked out of position (e.g.
when parking), the mirrors must first be fully retracted with the electric control. Do not readjust the mirror housing by hand, as this will
interfere with the mirror adjuster function.
Note
If the electrical adjustment should ever fail to operate, the mirrors
can be adjusted by hand by lightly pressing the edge of the mirror
glass.
document_0900452a81b1b9de.book Seite 71 Donnerstag, 26. Juli 2007 9:16 09
Lights and vision
Applies to vehicles: with automatic anti-dazzle adjustment for exterior mirrors
Automatic anti-dazzle adjustment for exterior
mirrors
71
Digital compass
Applies to vehicles: with digital compass
Activating and deactivating the compass
The exterior mirrors darken together with the automatically
adjusting interior mirror. When the ignition is on, the mirrors will
darken automatically according to the amount of light received (for
example from the headlights of a vehicle behind).
The compass direction will appear in the mirror.
When the interior lights are switched on, or when reverse gear is
engaged, the mirrors revert to their original (i.e. not darkened)
condition.
WARNING
Electrolyte fluid can leak from a broken mirror. This fluid can cause
irritation to the skin, eyes, and respiratory organs. Wash thoroughly with clean water should you come into contact with this
fluid. Seek medical assistance if needed.
Caution
Electrolyte fluid leaking from a broken mirror can cause damage to
the paintwork or plastic surfaces. Use a sponge or similar to remove
the fluid as soon as possible.
•
Fig. 73 Interior mirror:
activated digital
compass
– To switch the compass on and off, press and hold
A until the compass display in the mirror
button A
⇒ fig. 73 appears or disappears.
The digital compass only works when the ignition is on. The points
of the compass are displayed as follows: N (North), NE (North East),
E (East), SE (South East), S (South), SW (South West), W (West), NW
(North West).
Note
If you switch off the anti-dazzle function for the interior mirror,
this will also deactivate the anti-dazzle function for the exterior
mirrors.
•
The automatic anti-dazzle function will only work properly if the
sun blind* for the rear window is not in use and there are no other
objects preventing light from reaching the interior mirror.
Controls
Safety
Driving tips
Note
To avoid inaccurate compass readings, do not hold any remote
controls or other electrical devices or metal objects near the interior
mirror.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 72 Donnerstag, 26. Juli 2007 9:16 09
72
Lights and vision
Applies to vehicles: with digital compass
Applies to vehicles: with digital compass
Setting the correct compass calibration zone
Calibrating compass
The correct compass calibration zone must first be set
before the compass can give an accurate reading.
The compass must be re-calibrated if the display is incorrect or inaccurate.
A until the letter C appears in the
– Press and hold button A
interior mirror.
– Drive in a circle at a speed of about 10 km/h until a point
of the compass is displayed in the interior mirror.
WARNING
Calibrate your compass at a location where there is no traffic so
that you do not endanger yourself or other road users (accident
risk).
Fig. 74 Map of compass calibration zones
A ⇒ page 71, fig. 73 until the
– Press and hold button A
currently set zone number is displayed on the interior
mirror.
A repeatedly until the correct zone number
– Press button A
appears. The adjustment mode will be ended automatically after a few seconds.
document_0900452a81b1b9de.book Seite 73 Donnerstag, 26. Juli 2007 9:16 09
Seats and storage
73
Seats and storage
Manual adjustment of front seats
Applies to vehicles: with manual seat adjustment
Applies to vehicles: with manual seat adjustment
It is possible to adjust the position and shape of the seat
manually so that you can travel in a safe and comfortable
sitting position.
Seat adjuster controls
There are several seat adjustment functions for your
comfort and convenience
Seat adjustment
Before adjusting your seat, please read and observe the
warnings ⇒
.
Moving seat backwards or forwards
1 ⇒ fig. 75 and move the seat to the
– Lift the lever A
desired position.
Fig. 75 Adjuster
controls on driver's
seat
Some of the controls shown are only fitted on certain models or are
optional extras.
Extending or shortening the thigh support*
2 below the seat cushion. The front seat
– Lift the control A
cushion will spring forward.
– Slide the seat cushion back to the normal position after
each use.
Adjuster controls
1
A
2
A
3
A
4
A
5
A
6
A
1 and move the seat further until
– Then release the lever A
the catch engages.
Moves seat backwards or forwards
Thigh support*
Adjusts angle of seat cushion*
Adjusts lumbar support*
Adjusts seat height
Adjusts backrest angle
Adjusting angle of seat cushion*
3 ⇒ fig. 75 up or down repeatedly (i.e.
– Pull the lever A
pump the lever).
Adjusting contour of lumbar support*
4 to
– Press the front or rear part of the adjuster switch A
increase or decrease the curvature of the lumbar support
as required.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 74 Donnerstag, 26. Juli 2007 9:16 09
74
Seats and storage
Adjusting height of lumbar support*
Electric adjustment of front seats
4 to
– Press the top or bottom part of the adjuster switch A
move the lumbar support upwards or downwards as
required.
Seat adjuster controls
Raising or lowering the seat
The arrangement of the switches corresponds with the
design of the seats.
5 ⇒ page 73, fig. 75 up or down repeat– Pull the lever A
edly (i.e. pump the lever).
Adjusting backrest angle
– Lean forwards to take your weight off the backrest.
6 ⇒ page 73, fig. 75 to set the
– Turn the adjuster wheel A
angle of the backrest as required.
Fig. 76 Front seat:
Adjuster controls
WARNING
•
Never adjust the driver's seat when the vehicle is moving - this
could lead to an accident.
•
Be careful when adjusting the seat height. Careless or uncontrolled use of the seat adjustment can cause injuries.
•
Do not drive with the backrests of the front seats reclined too
far as otherwise the seat belt and airbag could fail to restrain the
wearer properly in an accident, possibly leading to injury.
The adjustment switches for the seat and backrest correspond with
the design of the seat. The seats can be adjusted simply by pressing
the corresponding switch in the required direction.
Adjuster controls
A
A
B
A
C
A
D
A
Lumbar support
Seat adjuster
Backrest adjuster
Thigh support*
Seat adjustment
You can use the electrical adjustment to set the position,
angle and shape of the seat so that you can travel in a
safe and comfortable sitting position.
Before adjusting your seat, please read and observe the
warnings ⇒
.
document_0900452a81b1b9de.book Seite 75 Donnerstag, 26. Juli 2007 9:16 09
Seats and storage
Adjusting contour of lumbar support
WARNING
A to increase or
– Press the front or rear of switch A
decrease the curvature of the lumbar support as
required.
•
Adjusting height of lumbar support
The electrical seat adjustment also works when the ignition is
off and when the key is not in the ignition. To avoid accidental injuries, never leave children unattended in the vehicle.
A to move the
– Press the top or bottom of adjuster switch A
lumbar support upwards or downwards as required.
B ⇒ page 74, fig. 76 forwards or backA
Adjusting seat height
– Press switch
•
•
Be careful when adjusting the seat height. Careless or uncontrolled use of the height adjustment can cause injuries.
Do not drive with the backrests of the front seats reclined too
far as otherwise the seat belt and airbag could fail to restrain the
wearer properly in an accident, possibly leading to injury.
Seat memory
B up or down.
A
Memory for driver's seat
Raising/lowering seat at front
– Press the front of switch
Never adjust the driver's seat when the vehicle is moving - this
could lead to an accident.
•
Moving seat backwards or forwards
– Press switch
wards.
75
You can use the recall buttons in the driver's door to store
and recall the seat adjustments for two drivers.
B up or down.
A
Raising/lowering seat at rear
B up or down.
– Press the rear of switch A
Adjusting backrest angle
– Press switch
C forwards or backwards.
A
Extending or shortening the thigh support*
D below the seat cushion. The front seat
– Lift the control A
cushion will spring forward.
– Slide the seat cushion back to the normal position after
each use.
Controls
Safety
Driving tips
Fig. 77 Driver's door:
Seat memory
As well as the driver's seat position, the seat memory will store and
recall the exterior mirror settings (if the vehicle is equipped accordingly):
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 76 Donnerstag, 26. Juli 2007 9:16 09
76
Seats and storage
Storing and recalling settings
You can store and recall the settings for two different drivers using
the recall buttons 1 and 2 ⇒ page 75, fig. 77 ⇒ page 76.
In addition, the current settings are automatically stored when you
lock the vehicle and assigned to the remote control key that is being
used. When you unlock the vehicle, the system automatically recalls
the settings stored on that remote control key.
Switching seat memory on and off
The seat memory will be out of action if the OFF switch has been
pressed and the diode in the switch is lit. In this case, the setting
cannot be stored.
The stored settings will all remain in the memory. However, the seat
can now only be adjusted using the conventional electrical
adjustment.
Applies to vehicles: with seat memory
Storing and recalling settings
– If the driver's door is closed, press and hold down the
desired recall button until the programmed settings are
reached.
A tone will sound and the diode in the SET button ⇒ page 75,
fig. 77 will light up to confirm that the settings have been stored.
When you lock the vehicle the current settings are automatically
stored and assigned to the remote control key. However, the
settings assigned to the remote control key will not overwrite the
settings stored on recall buttons 1 and 2. The settings stored on the
recall buttons can be called up at any time. When you unlock the
vehicle, the settings assigned to the remote control key are recalled
automatically.
If your vehicle is also driven by other persons using your remote
control key, it is advisable to store your personal settings on one of
the recall buttons. You can then recall your own settings at any time
simply by pressing the corresponding recall button. When you lock
the vehicle these settings are then stored automatically and
assigned once again to the remote control key.
Storing settings
– Adjust the driver's seat as required.
– Adjust both exterior mirrors.
– Press the SET button. The diode in the switch will light
up to indicate that it is ready to store the settings. Now
press the desired recall button for at least a second.
– Release the button. The setting is now stored on the
selected recall button.
Recalling settings
– If the driver's door is open, press the desired recall
button briefly.
WARNING
•
For safety reasons, never recall seat settings when the vehicle
is moving - this could lead to an accident.
•
In an emergency the recall function can be stopped at any time
by pressing the ON/OFF switch, or by briefly pressing any of the
recall buttons.
document_0900452a81b1b9de.book Seite 77 Donnerstag, 26. Juli 2007 9:16 09
Seats and storage
Applies to vehicles: with seat memory
Activating memory for remote control key
The relevant function must be activated on the sound
system or MMI* so that the settings stored in the memory
can be recalled using the remote control key.
77
Head restraints
Adjusting the front head restraints
In combination with properly worn seat belts, the head
restraints offer effective protection. However, they must
always be properly adjusted to suit the height of the occupant.
Fig. 78 Display:
Driver's seat
Fig. 79 Front seat:
Adjusting head
restraint
– Select: Function selector button CAR > Seat adjustment
> Driver's seat > Remote control key > on.
Raising head restraint
– Take hold of the sides of the head restraint with both
hands.
– Push the head restraint upwards.
Lowering head restraint
– Take hold of the sides of the head restraint.
– Press button
downwards.
A ⇒ fig. 79 and push the head restraint
A
For best protection, the top of the head restraint should be at least
at eye level, or higher.
The height of the head restraints is adjustable. They should be set
to suit the height of the occupant. In combination with the seat
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 78 Donnerstag, 26. Juli 2007 9:16 09
78
Seats and storage
belts, the head restraints offer effective protection, provided they
are properly adjusted.
Adjusting the rear head restraints
Applies to vehicles: with front armrest
Front armrest
The armrest can be adjusted to several positions and
moved back and forwards.
Fig. 81 Armrest
between driver's seat
and front passenger's
seat
Fig. 80 Rear seats:
Head restraint
Raising head restraint
Adjusting armrest
– Take hold of the sides of the head restraint with both
hands.
– To adjust the position of the armrest, pull the armrest all
the way down.
– Push the head restraint upwards as far as it will go.
– Then lift the armrest gradually until it engages in the
desired position.
Lowering head restraint
– Take hold of the sides of the head restraint.
Moving armrest
A ⇒ fig. 80 and push the head restraint
– Press the button A
downwards.
– You can move the armrest backwards or forwards
⇒ fig. 81.
For best protection, the top of the head restraint should be at least
at eye level, or higher.
When the rear seats are not occupied the head restraints should be
moved to the lowest position so that they do not obstruct the
driver's field of vision.
Please note that the armrest can restrict the driver's movements
when it is lowered. The armrest should therefore be moved back
before driving in city traffic.
There is a storage compartment underneath the armrest.
document_0900452a81b1b9de.book Seite 79 Donnerstag, 26. Juli 2007 9:16 09
Seats and storage
Luggage compartment
79
WARNING (continued)
Loading the luggage compartment
•
Loads in the luggage compartment should be safely
secured.
•
Always store objects in the luggage compartment and secure
with suitable straps. This is especially important for heavy
objects.
When you transport heavy objects, always keep in mind that a
change of the centre of gravity can also cause changes in vehicle
handling.
•
Please observe the important safety warnings ⇒ page 186,
“Safe driving”.
Note
Fig. 82 Heavy items
should be placed as far
forwards as possible.
Adjust the tyre pressure to match the vehicle loading - the correct
pressures are specified on the sticker on the end face of the driver's
door.
To maintain safe handling on the road, please observe the
following points:
Applies to vehicles: with fastening rings
– Distribute the weight as evenly as possible.
There are four fastening rings in the luggage compartment which can be used to secure loads.
– Position heavy items as far forward as possible ⇒ fig. 82.
Fastening rings
– Secure the load with the luggage net* or with non-elastic
straps secured to the fastening rings* ⇒ page 79.
WARNING
•
Unsecured objects in the luggage compartment can suddenly
shift and cause changes in the handling of the vehicle.
•
Fig. 83 Location of
fastening rings in
luggage compartment
In an accident or a sudden manoeuvre, loose objects in the
passenger compartment can be flung forward and possibly injure
vehicle occupants.
– Use the fastening rings to secure the load ⇒ fig. 83
-arrows-.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 80 Donnerstag, 26. Juli 2007 9:16 09
80
Seats and storage
– Please refer to the safety notes ⇒ page 193.
Retaining net
Applies to vehicles: with stretch net
– Secure the hooks of the retaining net to the fastening
rings at the bottom of the tail panel ⇒ fig. 85.
Stretch net / retaining net
The stretch net / retaining net can be used to secure light
items in the luggage compartment.
– Pull down the retaining hooks at the top of the luggage
compartment. Pull up the net and attach the loops of the
net to the retaining hooks.
You can also use the retaining hooks ⇒ fig. 85 to secure light items
of luggage, such as shopping bags, etc.
The hooks will fold up again by themselves when not in use.
WARNING
The retaining net should only be used to hold objects weighing up
to 5 kg. Heavier objects cannot be safely secured (injury risk).
Fig. 84 Stretch net laid
out
Side storage compartment
The DVD player for the navigation system* is located in
the left side compartment in the luggage compartment.
Fig. 85 Stretch net
attached in position as
retaining net
Stretch net
– First secure the front hooks in the fastening rings
⇒ fig. 84.
– Then secure the rear hooks in the fastening rings.
Fig. 86 Luggage
compartment: Side
trim with closed
storage compartment
document_0900452a81b1b9de.book Seite 81 Donnerstag, 26. Juli 2007 9:16 09
Seats and storage
Fig. 87 Luggage
compartment: DVD
player for navigation
system
– To open the storage compartment, pull the handle
⇒ page 80, fig. 86.
DVD player for navigation system*
The DVD player for the navigation system is located in this storage
compartment ⇒ fig. 87 in the luggage compartment. For more
information, please refer to the Infotainment/MMI Operating
Manual.
Extending the luggage compartment
The two sections of the backrest can be folded forwards
either together or separately to increase the capacity of
the luggage compartment.
81
Fig. 89 Locking the
backrest
Folding down backrest
– Press the release lever
cated (arrow).
A ⇒ fig. 88 in the direction indiA
– Fold down the backrest.
Returning backrest to an upright position
– Push the backrest up until it engages securely ⇒
. The
B should no longer be visible
red marking on the tab A
when the backrest is properly secured.
When the backrest is properly engaged in its upright position, it can
be locked and unlocked with the key ⇒ fig. 89. This prevents unauthorised access to the luggage compartment from inside the
vehicle.
WARNING
•
Make sure that the rear backrest is securely locked in position
so that the seat belt can provide proper protection on the centre
rear seat.
•
Fig. 88 Backrest
release lever
Controls
Safety
Driving tips
The rear backrest must always be securely latched so that
objects stored in the luggage compartment will not fly forward
during sudden braking.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 82 Donnerstag, 26. Juli 2007 9:16 09
82
Seats and storage
Applies to vehicles: with load-through hatch
Caution
When returning the backrest to an upright position, make sure that
the seat belts for the outer rear seats are in their guides so that they
cannot be caught up and damaged in the catches for the backrest.
Storage shelf
Load-through hatch with transport bag
You can use the load-through hatch and the removable
ski bag to transport skis or other extra-long objects safely
inside the vehicle without soiling or damaging the upholstery.
The storage shelf behind the rear backrest should only be
used to store light articles of clothing.
WARNING
Do not store any heavy or hard objects on the storage shelf. They
could cause injury if the brakes are applied suddenly.
Fig. 90 Rear seat:
Cover of load-through
hatch
Caution
Please note that hard objects could chafe against the wires of the
heating element in the rear window and cause damage.
Note
Make sure that the slots between the rear window and the storage
shelf are kept clear to ensure unimpaired ventilation.
Fig. 91 Securing the
ski bag with the centre
seat belt buckle on the
rear seat
Loading
– In the passenger compartment, pull down the centre rear
armrest.
– You will then see the inside cover of the load-through
hatch - pull the release catch downwards ⇒ fig. 90
-arrow- to fold the hatch down.
document_0900452a81b1b9de.book Seite 83 Donnerstag, 26. Juli 2007 9:16 09
Seats and storage
– Open the boot lid.
Roof carrier
– Open out the ski bag and fill it with the items you wish to
transport.
Applies to vehicles: with roof carrier: Under development at the time of print
– Push the ski bag from the luggage compartment into the
passenger compartment through the opening in the
backrest ⇒
.
Description
Additional loads can be transported using the roof carrier.
Note the following points if you intend to carry loads on the roof:
•
Securing
A ⇒ page 82, fig. 91 of the ski
– Insert the fastening belt A
B .
bag into the centre seat belt buckle A
– Pull the free end of belt
83
The rain channels are moulded into the roof as part of the aerodynamic roof design. It is therefore not possible to mount conventional roof luggage racks. We recommend using the carrier units
from the range of Audi Genuine accessories.
•
These carrier units form the basic elements of a complete roof
carrier system. Special fixtures must then be added in order to
safely transport luggage, bicycles, skis, surf boards or boats on the
roof. All the elements of this system are available from Audi dealers.
C to tighten.
A
Storage
– Pull the ski bag towards the rear through the opening in
the backrest.
– Close the cover of the load-through hatch in the
passenger compartment.
– Fold up the ski bag.
Caution
Any damage to the vehicle caused by the use of other types of roof
rack or incorrect installation will not be covered by the factory
warranty. The roof carrier system must therefore be installed exactly
according to the instructions provided.
WARNING
The ski bag must be secured in place with the fastening belt after
it has been loaded.
Note
Allow the ski bag to dry before folding it up.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 84 Donnerstag, 26. Juli 2007 9:16 09
84
Seats and storage
Attachment points
Roof load
The roof carrier must be attached at the marked points
only.
Loads carried on the roof must be securely attached. The
car's handling is affected when transporting loads.
The maximum permissible roof load for your vehicle is 90 kg. The
load limit applies to the combined weight of the carrier system and
the load itself.
It will not be possible to carry the full maximum load if the roof
carrier you are using is rated for a load which is less than this figure.
Do not exceed the maximum weight limit for the roof carrier, which
is listed in the fitting instructions.
Fig. 92 Attachment
points for carrier units
Mounting
The feet of the roof carrier must always be attached at the position
where the holes in the roof frame are located ⇒ fig. 92. The holes
are only visible when the doors are open. When using roof carriers
with pins, make sure that the pins are securely fixed in the holes
when mounting the carrier units.
WARNING
After driving a few kilometres, check that the roof carrier is
securely attached.
Note
Each roof carrier has a marking to indicate whether it is to be fitted
at the front or rear of the vehicle.
WARNING
•
To prevent accidents, loads carried on the roof must be
securely attached.
•
Do not exceed the maximum roof load for the vehicle, the
maximum axle loads or the maximum gross vehicle weight, as this
could cause an accident.
•
When transporting heavy or bulky loads on the roof, bear in
mind that the car's handling is affected by the extra weight on the
roof and a possible susceptibility to cross winds. Adjust your
speed and driving style accordingly to avoid accidents.
For the sake of the environment
The increased air resistance when the roof carrier is fitted means
that the vehicle uses more fuel. For this reason you should always
take off the roof carrier when it is not in use.
document_0900452a81b1b9de.book Seite 85 Donnerstag, 26. Juli 2007 9:16 09
Seats and storage
Cup holders
85
– Position the cup in the holder and let go of the arm. The
arm will move back automatically to secure the cup.
Closing cup holder
– Press the middle piece between the two arms and push
the cup holder back into the shaft as far as it will go.
The retainer arm should be positioned against the drinks container
so that it is held securely.
Fig. 93 Centre console:
Front cup holder
One or two drink containers can be held in the centre armrest.
WARNING
•
Do not put any hot drinks in the cup holders while the vehicle
is moving. You could be scalded if the hot liquid is spilt.
•
Do not use hard china cups or glasses. These could cause injury
in the event of an accident.
Caution
Fig. 94 Cup holder in
rear armrest
You should avoid putting open drinks containers in the cup holders.
The drinks could otherwise spill over and cause damage to e.g. the
electrical equipment or the seat covers.
Front cup holder
– Two drinks can be placed in this cup holder ⇒ fig. 93.
Opening rear cup holder
A ⇒ fig. 94.
– Press the symbol  A
Placing drinks in rear cup holder
– To adjust the arm of the cup holder
direction indicated by the arrow.
Controls
Safety
B , move it in the
A
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 86 Donnerstag, 26. Juli 2007 9:16 09
86
Seats and storage
Ashtrays
Rear ashtray
Front ashtray
Fig. 96 Rear centre
console: Ashtray
Fig. 95 Centre console:
Ashtray open
Opening ashtray
– Pull the front lip of the ashtray
tion of the arrow.
Opening ashtray
– Slide the cover open.
B ⇒ fig. 96 in the direcA
Removing ashtray
Closing ashtray
– Press down the retainer
– Lightly press the cover to make the ashtray close automatically.
Inserting ashtray
A and take out the ashtray.
A
– Place the ashtray in the holder.
Removing ashtray
– Slide the switch
ashtray.
A ⇒ fig. 95 to the right to release the
A
– Take out the ashtray
B ⇒ fig. 95.
A
Inserting ashtray
– Insert the ashtray and press it into its mountings.
WARNING
Never put waste paper in the ashtray, as this could cause a fire.
WARNING
Never put waste paper in the ashtray, as this could cause a fire.
document_0900452a81b1b9de.book Seite 87 Donnerstag, 26. Juli 2007 9:16 09
Seats and storage
Cigarette lighter and electrical
sockets
87
The cigarette lighter employs a standard 12 Volt socket which can
also be used as a power source for electrical appliances. The appliances connected to the socket must not exceed a power rating of
100 W.
Cigarette lighter
The cigarette lighter only works when the ignition is on.
WARNING
•
Take care when using the cigarette lighter. Carelessness or
negligence when using the cigarette lighter can cause burns.
•
Fig. 97 Front ashtray
(open)
The electrical sockets and any appliances connected to them
will operate only when the ignition is switched on. Improper use
of the electrical sockets or the appliances connected to them can
cause injuries or fire. To avoid the risk of injury, never leave children unsupervised in the vehicle with the key.
Using cigarette lighter
– Open the cover of the front ashtray.
•
– Press in the cigarette lighter knob.
•
Caution
Always use the correct type of plugs to avoid damaging the
sockets.
The cigarette lighter socket should only be used for a short
period of time as a power source for electrical equipment. Please
use the electrical sockets* ⇒ page 88 in the vehicle when
connecting equipment for longer periods.
– Wait for the lighter to spring out.
– Pull out the cigarette lighter immediately.
– Use the glowing heater element of the cigarette lighter to
light your cigarette.
– Put the cigarette lighter back in its socket.
Note
Using electrical appliances with the engine switched off will drain
the battery.
Operating electrical socket
– Take out the cigarette lighter.
– Insert the plug of the electrical appliance into the cigarette lighter socket.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 88 Donnerstag, 26. Juli 2007 9:16 09
88
Seats and storage
– Insert the plug of the electrical appliance into the socket.
Applies to vehicles: with 12 Volt sockets
12 Volt sockets
Electrical equipment can be connected to both 12 Volt
sockets.
Electrical equipment can be connected to the 12 Volt socket. The
appliances connected to the socket must not exceed a power rating
of 150 W.
WARNING
Fig. 98 Detail of the
side trim in the
luggage compartment:
12 Volt socket
The electrical sockets and any appliances connected to them will
operate only when the ignition is switched on. Improper use of the
electrical sockets or the appliances connected to them can cause
injuries or fire. To avoid the risk of injury, never leave children
unsupervised in the vehicle with the key.
•
Caution
To avoid damage to the vehicle's electrical system, never
connect equipment that generates electrical current, such as a solar
panel or battery charger, to the 12 Volt sockets or cigarette lighter in
order to charge the vehicle's battery.
•
Use only equipment which has been tested for electromagnetic
compatibility in compliance with EC Directive 2004/104/EC.
Fig. 99 Electrical
socket in the centre
console
Electrical socket in luggage compartment and
front centre console
– Open the cover cap concealing the socket ⇒ fig. 98.
– Insert the plug of the electrical appliance into the socket.
Electrical socket in rear centre console
– Fold up the lid ⇒ page 89, fig. 100 to access the socket.
Note
Using electrical appliances with the engine switched off will drain
the battery.
document_0900452a81b1b9de.book Seite 89 Donnerstag, 26. Juli 2007 9:16 09
Seats and storage
89
If you connect more than one appliance, the total power rating of all
appliances must not exceed 150 W. If necessary, check the type
plates on the connected appliances for details of the power ratings.
Applies to vehicles: with 230 Volt Euro socket
On-board 230 Volt Euro socket
Electrical equipment can be connected to the 230 Volt
Euro socket in the rear centre console.
Connected appliances must be in perfect condition and free of
defects.
WARNING
•
Heavy appliances or plugs (such as power supply units) can
damage the mounting of the 230 Volt Euro socket if they are
suspended directly from the socket – Risk of injury!
•
Fig. 100 Rear centre
console: 230 Volt Euro
socket
The 230 Volt Euro socket can only be used when the ignition
is on ⇒
.
Make sure that all connected appliances are securely stowed
when driving to prevent them from being catapulted through the
car under braking or in an accident – Danger to life!
•
Never spill liquid over the socket – Danger to life! If the socket
does get wet, ensure that it is absolutely dry before using it again.
•
Improper use of the electrical socket or appliances connected
to it can cause injuries or fire – Risk of injury!
– Fold up the lid to access the socket.
•
– Plug the Euro connector into the socket. This will automatically release the child safety device.
•
LED in electrical socket
•
Never leave children unattended in the vehicle while the engine
is running – Risk of injury!
Steady green light:
The socket is ready for use.
Flashing red light:
The socket has tripped out due
to a power surge, overheating or
similar
Electrical equipment with a Euro plug connector can be connected
to the 230 Volt Euro socket. The appliances connected to the
230 Volt Euro socket must not exceed a power rating of 150 W
(300 W peak power).
Safety
When using adapters or extension cables, please remember
that the child safety device on the 230 Volt Euro socket is deactivated and the socket is live – Risk of injury!
•
Do not insert conductive materials, such as knitting needles,
into the contacts of the 230 Volt Euro socket – Danger to life!
•
Switch off the connected electrical appliances if the inverter
trips out due to overheating – Risk of injury!
Appliances suitable for connection
Controls
Connected appliances behave differently than when they are
connected to the public electricity grid. As a result, the connected
appliances may become hot during operation – Risk of injury!
Driving tips
•
Caution
Please observe the operating instructions for the connected
appliances.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 90 Donnerstag, 26. Juli 2007 9:16 09
90
Seats and storage
•
If the power drawn by the connected appliances is above 150 W,
the inverter in the socket will get warm. The inverter will trip out if
the temperature exceeds a certain limit. The inverter can trip out on
hot days even when an appliance with a suitable power rating is
used. The inverter will switch on again automatically after it has
cooled down. Appliances which are already connected and
switched on will be activated again automatically ⇒
.
Storage compartments
•
Do not connect lamps which contain a neon tube. For technical
reasons, this may damage the lamp.
Glove box
⇒ page 90
•
Compartment for (sun)glasses in headliner
⇒ page 91
Do not connect 115 Volt appliances to the 230 Volt Euro socket.
This may cause irreparable damage to the appliance. Check the type
plate on the appliance if you are unsure of the voltage rating.
•
With some power supplies (e.g. on laptop computers), the integrated surge suppressor prevents the equipment from being
switched on because the starting current is too high. If this
happens, please disconnect the power supply unit from the load
and wait for about 10 seconds before re-connecting.
•
Overview
There are several storage compartments at various points
in the vehicle.
Storage compartments in the front seats ⇒ page 91
Coat hooks
⇒ page 91
First-aid kit
⇒ page 282
Side storage compartment in luggage
compartment
⇒ page 80
Warning triangle
⇒ page 282
Note
Unshielded equipment can cause interference on the radio, TV
and vehicle's electrical system.
•
The Euro socket has an integrated child safety device. There is no
power at the socket until the Euro connector is fully inserted.
Glove box
The glove box is equipped with a lock* and a light.
•
Some appliances may not function normally due to the lower
power rating (wattage).
•
The socket can be operated with 115 Volt power supplies, as is
the case in certain countries. In this case, a different type of inverter
must be installed in the vehicle. Retrofit kits are available from your
Audi dealer. Do not connect 115 Volt appliances to the 230 Volt Euro
socket.
•
Interference can occur on the radio's AM waveband if electrical
appliances are used near the rear window aerial.
Fig. 101 Glove box
document_0900452a81b1b9de.book Seite 91 Donnerstag, 26. Juli 2007 9:16 09
Seats and storage
Opening glove box
– Pull the catch on the lid in the direction indicated (arrow)
⇒ page 90, fig. 101 and open the lid.
Closing glove box
91
WARNING
Always keep the compartment cover closed while the vehicle is in
motion to reduce the risk of injury during a sudden braking
manoeuvre or in the event of an accident.
– Close the lid and push it in until it engages.
Coat hooks
The glove box lid has separate holders for a pen and a note pad.
On the right-hand side of the glove box there is a holder with a key
shell. In order to start the engine with the spare key, it has to be
clipped into this shell.
The coat hooks are located on the rear side of the B-pillars
(in the rear passenger compartment).
WARNING
•
WARNING
To avoid the risk of injuries, always keep the glove box lid closed
when driving.
Compartment for (sun)glasses in headliner
Please make sure that any items of clothing hanging from the
coat hooks do not obstruct your view to the rear.
•
Only use the coat hooks for light items of clothing and make
sure that there are no heavy or sharp objects in the pockets.
•
Do not use clothes hangers to hang up the clothing, as this
could interfere with the function of the head-protection
airbags*.
Applies to vehicles: with storage compartments in the front seats
Storage compartments in front seats
There is a fold-out drawer in the front part of each front
seat.
Fig. 102 Compartment
for (sun)glasses in
headliner
– To open the cover, lightly press the panel ⇒ fig. 102
(arrow). The cover will then open by itself.
Opening
– Pull the handle to open the compartment.
Closing
– Close the lid and push it in until it engages.
– To close the cover, push it upwards until it engages.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 92 Donnerstag, 26. Juli 2007 9:16 09
92
Seats and storage
Note
The storage compartment will hold a maximum weight of 1 kg.
document_0900452a81b1b9de.book Seite 93 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
93
Heating and cooling
Deluxe automatic air conditioner
Applies to vehicles: with deluxe automatic air conditioner
The compressor also switches off if the coolant temperature is
excessively high, to ensure adequate engine cooling under extreme
loads.
Description
Pollution filter
The air conditioner can be used to set a comfortable interior temperature in the vehicle.
The pollution filter (a particle filter) serves as a barrier against impurities in the outside air, including dust and pollen, and odours. The
air is also filtered when the air recirculation mode is activated.
The air conditioner provides heating and ventilation and also cools
and dehumidifies the air inside the vehicle.
For the air conditioner to work with maximum efficiency, the pollution filter element must be replaced at the intervals specified in the
Service Schedule.
The air conditioner is fully automatic and will maintain the desired
temperature at a constant level. To achieve this, the temperature of
the air supplied to the interior, the blower speed (volume of air
delivery) and the air distribution are regulated automatically. The
system also allows for the effect of strong sunlight, so there is no
need for manual adjustment. For these reasons it is advisable to use
the automatic mode for the comfort of all the passengers in virtually
all conditions throughout the year ⇒ page 95.
Please note:
Key-coded settings
The currently selected air conditioner settings are automatically
stored and assigned to the remote control key.
Power management
The humidity of the air is automatically reduced when the system
cools the interior of the vehicle. This helps to prevent condensation
on the windows.
If the humidity and temperature outside the vehicle are high,
condensation can drip off the evaporator in the air cooling system
and form a pool underneath the vehicle. This is normal and does not
indicate a leak.
If the outside temperature is low, the blower normally only switches
to a higher speed once the coolant has warmed up sufficiently (this
does not apply to the defrost setting).
In order to achieve maximum engine power, the air conditioner
compressor is temporarily switched off when pulling away from a
standstill with full throttle.
Controls
If the vehicle is driven in areas with a high level of air pollution and
the filter is no longer fully effective, it may be necessary to change
the filter element more frequently.
Safety
Driving tips
To prevent the battery from becoming discharged and to maintain
the necessary power level, the system will temporarily shut off the
electrical components that are using a lot of power, or reduce the
current they are consuming ⇒ page 226. Heating systems in particular use a large amount of electrical power. If you notice, for
instance, that the rear window heater is not working, it may have
been temporarily switched off by the power management function,
or regulated to a lower heat output. These systems will be available
again as soon as sufficient electrical power is available.
WARNING
For safety reasons it is important that all the windows are kept
free of ice, snow and condensation. These can cause poor visibility
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 94 Donnerstag, 26. Juli 2007 9:16 09
94
Heating and cooling
Applies to vehicles: with deluxe automatic air conditioner
WARNING (continued)
and lead to an accident. Please familiarise yourself with the operating controls for the air conditioner, including the demist/defrost
functions for the windows.
•
Controls
The controls for the air conditioner at a glance.
Caution
If you suspect that the air conditioner is damaged, switch it off
to prevent further damage and have the system checked by a qualified workshop.
•
Repairs to the Audi air conditioner require specialist knowledge
and special tools. For this reason, please contact a qualified workshop if the system is not working properly.
•
Note
Keep the air intake slots in front of the windscreen clear of snow,
ice and leaves to ensure unimpaired heating and cooling, and to
prevent the windows misting over.
•
The air from the outlets flows through the passenger compartment and out through the slots at the rear of the vehicle. Do not
cover these slots with clothing or other objects.
•
The air conditioner operates most effectively with the windows
and the tilting panorama roof* closed. However, if the vehicle has
heated up after standing in the sun for some time, the air inside can
be cooled more quickly by opening the windows for a short time.
Fig. 103 Controls for deluxe automatic air conditioner
The functions can be set by turning the rotary control and are
switched on and off by briefly pressing the buttons. The LEDs in the
buttons light up when the function is switched on.
Button(s)
Function
Page
OFF
Switching on and off
⇒ page 95
AUTO
Automatic mode
⇒ page 95
Rotary controla)
Temperature selection
⇒ page 96

Blower
⇒ page 96

Air recirculation mode
⇒ page 97
document_0900452a81b1b9de.book Seite 95 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
Applies to vehicles: with deluxe automatic air conditioner
Button(s)
Function
Page

Air distribution
⇒ page 97

Defrosting windows
⇒ page 98

Heated rear window
⇒ page 98
AC
Switching air cooling
on/off
⇒ page 98

Seat heating
⇒ page 114
a)
95
Automatic mode AUTO
The standard operating mode for all seasons.
Switching on automatic mode
– Select a temperature between +16 °C (60 °F) and +28 °C
(84 °F).
– Press the AUTO button.
The rotary control is also used to adjust the blower speed, air distribution
and seat heating.
Note
The grille on the control console ⇒ page 94, fig. 103 must be kept
free. Please ensure that it is not covered by stickers or similar. Measuring sensors are located behind it.
Applies to vehicles: with deluxe automatic air conditioner
Switching on and off
Switching on air conditioner
The automatic mode maintains a constant temperature inside the
vehicle and dehumidifies the air. Air temperature, air delivery and
air distribution are regulated automatically to reach the desired
interior temperature as quickly as possible, and then to maintain
this temperature. The system automatically compensates for any
variations in the outside temperature and for the effect of direct
sunlight.
The automatic temperature regulation only operates at temperature
settings between +16 °C and +28 °C. If a temperature below +16 °C
is selected, LO appears on the display. If a temperature above +28 °C
is selected, the display will show HI. In the two extreme settings the
air conditioner operates continuously with maximum cooling or
heating output, and the temperature is not regulated
automatically.
– Press the OFF button briefly, or
– Press the AUTO button.
Switching off air conditioner
– Press the OFF button to switch off the air conditioner
and cut off the supply of fresh air from outside the
vehicle.
The air conditioner will switch on again if one of the control buttons
is pressed.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 96 Donnerstag, 26. Juli 2007 9:16 09
96
Heating and cooling
Applies to vehicles: with deluxe automatic air conditioner
Applies to vehicles: with deluxe automatic air conditioner
Temperature selection
Blower

The automatically selected blower speed can be reduced
or increased manually if required.
Fig. 104 Rotary control
for temperature selection
Fig. 106 Blower
button and rotary
control
Fig. 105 Display:
Temperature setting
Fig. 107 Display:
Blower setting
– Turn the rotary control anti-clockwise to reduce the
temperature or clockwise to increase the temperature
⇒ fig. 104.
– Press the button for the blower  .
The temperature setting will be shown on the screen ⇒ fig. 105 for
a few seconds if the sound system or MMI* is switched on.
– Turn the rotary control to set the blower to the desired
speed (and regulate the volume of air delivery).
We recommend keeping the blower running at a low setting when
driving slowly.
To prevent fumes or unpleasant smells from entering the vehicle,
switch to the air recirculation mode by pressing the  button.
document_0900452a81b1b9de.book Seite 97 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
The blower speed will be shown on the screen ⇒ page 96, fig. 107
for a few seconds if the sound system or MMI* is switched on.
•
97
WARNING (continued)
entering the vehicle, so the windows can mist over if the air
cooling is switched off. Bad visibility can cause an accident.
Note
The blower speed may change automatically. This ensures that
the selected temperature is reached as quickly as possible.
•
The blower speed cannot be regulated separately for the driver
and front passenger sides of the vehicle.
Applies to vehicles: with deluxe automatic air conditioner
Air distribution

The automatically programmed air distribution can be
altered manually if required.
Applies to vehicles: with deluxe automatic air conditioner
Air recirculation mode 
The air recirculation setting prevents fumes etc. from
entering the interior.
Switching on the air recirculation mode
– Press the  button ⇒
.
Fig. 108 Air distribution button and rotary
control
Switching off the air recirculation mode
– Press the  button again, or
– Press the AUTO button, or
– Press the  button.
In this setting, the air is drawn from the interior of the vehicle,
filtered and continuously recirculated. We recommend using the air
recirculation mode in the following circumstances:
When driving through a tunnel or in queues of traffic, to prevent
fumes entering the interior of the vehicle.
– Press the button for Distribution .
WARNING
For reasons of safety you should not leave the air recirculation
switched on for too long. This mode prevents fresh air from
Controls
Fig. 109 Display: Air
distribution
Safety
Driving tips
– Turn the rotary control to the desired setting.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 98 Donnerstag, 26. Juli 2007 9:16 09
98
Heating and cooling
You can use the air distribution setting to select the air outlets you
wish to activate. In setting  all the air is directed to the windows,
in setting  the air is directed to the driver (or passenger), and in
setting  to the footwells. In addition to this there are several other
possible combinations, allowing you to adjust the air distribution to
suit individual requirements.
Switch to AUTO for automatic control of the air distribution.
The air distribution setting will be shown on the screen ⇒ page 97,
fig. 109 for a few seconds if the sound system or MMI* is switched
on.
Applies to vehicles: with deluxe automatic air conditioner
Defrosting 
The windscreen and side windows are defrosted or
demisted as quickly as possible.
– To switch on, press the  button.
– To switch off, press the  button again, or press the
AUTO button.
The rear window heating only works when the engine is running. An
indicator lamp in the button lights up when the rear window heater
is switched on.
Depending on the outside temperature, the rear window heating
switches off automatically after about 10 to 20 minutes.
The rear window heating can be switched on permanently by
pressing the  button for longer than two seconds. It will then
remain on until the ignition is switched off. When the rear window
heating is switched on, this setting will remain activated for 15
minutes after switching off the ignition.
If the engine is started again during this period of 15 minutes, the
rear window heating will be switched on for about 10 to 20 minutes,
depending on the exterior temperature. This means you do not have
to manually switch on the rear window heating again if the vehicle
has only been parked for a short time.
For the sake of the environment
Switch off the heated rear window manually as soon as the rear
window is clear. By saving electrical power you can also save fuel.
The temperature is regulated automatically. The air output is
increased to maximum and most of the air comes out of the outlets
below the windscreen.
Applies to vehicles: with deluxe automatic air conditioner
The air recirculation mode is switched off when the  button is
pressed.
Deactivating the AC mode
Applies to vehicles: with deluxe automatic air conditioner
Activating the AC mode
Heated rear window 
– Press the AC button again.
The rear window heating helps to demist the rear window.
– Press the  button to switch the rear window heating on
and off.
AC mode AC
– Press the AC button.
In the AC mode, the air cooling system is switched on and the
heating and ventilation are regulated automatically.
document_0900452a81b1b9de.book Seite 99 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
Note
If the LED in the AC button should continue to light up when the AC
mode has been switched off (i.e. the air conditioner has been
switched off) this is due to a defect in one of the air conditioner
components. If a malfunction should occur, please contact a qualified workshop.
Applies to vehicles: with deluxe automatic air conditioner
99
– The direction of air delivery from these outlets can be
adjusted horizontally and vertically using the adjuster in
the centre of each outlet grille.
The flow of air from the outlets is controlled either automatically or
manually, depending on the operating mode selected. All the
outlets can provide air which is either heated, unheated, or cooled.
Note
Air outlets
The air distribution setting directs the air to the outlets
you select.
When the air conditioner is operating in the cooling mode, the air is
2 and A
3 . To ensure an adequate cooling
directed mainly to outlets A
effect, you should not close these outlets completely.
Applies to vehicles: with deluxe automatic air conditioner
Air outlets for rear passengers
The air outlets for the rear cabin are located in the centre
console.
– The outlets can be opened and closed by turning the
thumbwheels.
– The direction of air delivery from these outlets can be
adjusted horizontally and vertically using the adjuster in
the centre of each outlet grille.
The flow of air from the outlets is controlled either automatically or
manually, depending on the operating mode selected. All the
outlets can provide air which is either heated, unheated, or cooled.
The heater outlets for the rear footwells are located under the front
seats.
Fig. 110 Dashboard: Location of air outlets
Air outlets
2 and A
3
A
– The outlets can be opened and closed by turning the
thumbwheels next to them.
Controls
Safety
Driving tips
Note
When the air conditioner is operating in the cooling mode the air is
directed mainly to the outlets in the centre console. To ensure an
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 100 Donnerstag, 26. Juli 2007 9:16 09
100
Heating and cooling
adequate cooling effect, you should not close these outlets
completely.
Deluxe automatic air conditioner basic settings
Applies to vehicles: with deluxe automatic air conditioner
Applies to vehicles: with deluxe automatic air conditioner
Economical operation of the air conditioner
General notes
Economical operation of the air conditioner will help to
save fuel.
The basic settings for the air conditioner can be adjusted
via the sound system or MMI*.
When the air conditioner is operating in the cooling mode it
reduces engine power and increases fuel consumption. To
ensure that the cooling mode is activated only when really
necessary, please note the following points:
– Switch off the cooling mode by pressing the AC button
(LED off) if you wish to save fuel.
– You should also switch off the cooling mode by pressing
the AC button (LED off) if you open the windows or the
tilting panorama roof* while driving.
– If the vehicle has heated up after standing in the sun,
open the windows and doors for a short time to cool the
vehicle.
For the sake of the environment
By saving fuel you also reduce the amount of pollutants emitted
from your vehicle.
Fig. 111 Display:
Setup AC
– Select: Function selector button CAR > control button
AC.
The following functions are available:
•
•
•
•
•
•
•
•
Auxiliary heating* ⇒ page 110
Auxiliary ventilation* ⇒ page 110
Running time* ⇒ page 112
Timer status* ⇒ page 111
Timer 1* ⇒ page 111
Timer 2* ⇒ page 111
Timer 3* ⇒ page 111
Supplementary heater* ⇒ page 101
document_0900452a81b1b9de.book Seite 101 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
If the humidity and temperature outside the vehicle are high,
condensation can drip off the evaporator in the air cooling system
and form a pool underneath the vehicle. This is normal and does not
indicate a leak.
Applies to vehicles: with diesel engine
Supplementary heater
– Set the Supplementary heater to auto or off.
Models with a diesel engine are equipped with a supplementary
heater to help warm up the interior more quickly. At outside temperatures below about +5 °C the supplementary heater is switched on
(and off) automatically when the engine is running, depending on
the coolant temperature, the temperature in the vehicle interior and
the temperature the heater is set to.
Deluxe automatic air conditioner plus
Description
The air conditioner is designed to keep the passenger
compartment at the temperature you find most comfortable at all times of the year.
The air conditioner provides heating and ventilation and also cools
and dehumidifies the air inside the vehicle.
The air conditioner is fully automatic, and will maintain the desired
temperature at a constant level. To achieve this, the temperature of
the air supplied to the interior, the blower speed (volume of air
delivery) and the air distribution are regulated automatically. The
system also allows for the effect of strong sunlight, so there is no
need for manual adjustment. For these reasons it is advisable to use
the automatic mode for the comfort of all the passengers in virtually
all conditions throughout the year ⇒ page 103.
Please note:
The humidity of the air is automatically reduced when the system
cools the interior of the vehicle. This helps to prevent condensation
on the windows.
Safety
If the outside temperature is low, the blower normally only switches
to a higher speed once the coolant has warmed up sufficiently (this
does not apply to the defrost setting).
In order to achieve maximum engine power, the air conditioner
compressor is temporarily switched off when pulling away from a
standstill with full throttle.
The compressor also switches off if the coolant temperature is
excessively high, to ensure adequate engine cooling under extreme
loads.
Pollution filter
Applies to vehicles: with deluxe automatic air conditioner plus
Controls
101
Driving tips
The pollution filter (a combined particle filter and activated charcoal
filter) serves as a barrier against impurities in the outside air,
including dust and pollen, and against unpleasant smells. The air is
also filtered when the air recirculation mode is activated.
For the air conditioner to work with maximum efficiency, the pollution filter element must be replaced at the intervals specified in the
Service Schedule.
If the vehicle is driven in areas with a high level of air pollution and
the filter is no longer fully effective, it may be necessary to change
the filter element more frequently.
Key-coded settings
The currently selected air conditioner settings are automatically
stored and assigned to the remote control key.
Power management
To prevent the battery from becoming discharged and to maintain
the necessary power level, the system will temporarily shut off the
electrical components that are using a lot of power, or reduce the
current they are consuming ⇒ page 226. Heating systems in particular use a large amount of electrical power. If you notice, for
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 102 Donnerstag, 26. Juli 2007 9:16 09
102
Heating and cooling
instance, that the rear window heater is not working, it may have
been temporarily switched off by the power management function,
or regulated to a lower heat output. These systems will be available
again as soon as sufficient electrical power is available.
Applies to vehicles: with deluxe automatic air conditioner plus
Controls
The controls for the air conditioner at a glance.
WARNING
For safety reasons it is important that all the windows are kept
free of ice, snow and condensation. These can cause poor visibility
and lead to an accident. Please familiarise yourself with the operating controls for the air conditioner, including the demist/defrost
functions for the windows.
•
Caution
If you suspect that the air conditioner is damaged, switch it off
to prevent further damage and have the system checked by a qualified workshop.
•
Repairs to the air conditioning system require specialist knowledge and special tools. For this reason, please contact a qualified
workshop if the system is not working properly.
Fig. 112 Air conditioner controls
•
Note
Keep the air intake slots in front of the windscreen clear of snow,
ice and leaves to ensure unimpaired heating and cooling, and to
prevent the windows misting over.
•
The air from the outlets flows through the passenger compartment and out through the slots at the rear of the vehicle. Do not
cover these slots with clothing or other objects.
•
The air conditioner operates most effectively with the windows
and the tilting panorama roof* closed. However, if the vehicle has
heated up after standing in the sun for some time, the air inside can
be cooled more quickly by opening the windows for a short time.
The left-hand display shows the temperature selected for the lefthand side, the right-hand display the temperature for the right-hand
side.
The functions can be switched on and off by turning the controls or
briefly pressing the buttons. The LEDs in the buttons light up when
the function is switched on.
document_0900452a81b1b9de.book Seite 103 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
103
Applies to vehicles: with deluxe automatic air conditioner plus
Button(s)
Function
Page
OFF
Switching on and off
⇒ page 103
AUTO
Automatic mode - drivers
side/
front passengers side
⇒ page 103
Temperature selection drivers side
Temperature selection front passengers side
⇒ page 104
Switching off air conditioner

Blower - driver's side/
front passenger's side
⇒ page 104
– Press the OFF button for at least 2 seconds to switch off
the air conditioner and cut off the supply of fresh air from
outside the vehicle. The display will show “OFF”.
 b)
Air recirculation mode
⇒ page 105
Air distribution - drivers
side/
front passengers side
⇒ page 106
Temperature control 1a)
Temperature control 2a)

Switching on and off
Switching on air conditioner
– Press the AUTO button.

Defrosting windows
⇒ page 106

Heated rear window
⇒ page 106
AC
Switching air cooling
on/off
⇒ page 107
 / 
Seat heating / seat ventila⇒ page 114
tion
a)
b)
•
The rotary control is also used to adjust the blower speed, air distribution
and seat heating.
The symbol differs slightly on some models.
Note
The air conditioner will switch on again if you operate the temperature control.
Note
You can press the OFF button when the ignition is switched off to
activate the "residual heat" function. The system will then heat the
interior using the remaining heat in the engine coolant.
Applies to vehicles: with deluxe automatic air conditioner plus
Automatic mode AUTO
The standard operating mode for all seasons.
Switching on automatic mode
– Select a temperature between +16 °C (60 °F) and +28 °C
(84 °F).
– Press the AUTO button.
The grille on the control console ⇒ page 102, fig. 112 must be
kept free. Please ensure that it is not covered by stickers or similar.
Measuring sensors are located behind it.
Controls
– Press the OFF button briefly, or
Safety
Driving tips
The automatic mode maintains a constant temperature inside the
vehicle and dehumidifies the air. Air temperature, air delivery and
air distribution are regulated automatically to reach the desired
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 104 Donnerstag, 26. Juli 2007 9:16 09
104
Heating and cooling
interior temperature as quickly as possible, and then to maintain
this temperature. The system automatically compensates for any
variations in the outside temperature and for the effect of direct
sunlight.
The automatic temperature regulation only operates at temperature
settings between +16 °C and +28 °C. If a temperature below +16 °C
is selected, LO appears on the display. If a temperature above +28 °C
is selected, the display will show HI. In the two extreme settings the
air conditioner operates continuously with maximum cooling or
heating output, and the temperature is not regulated
automatically.
Applies to vehicles: with deluxe automatic air conditioner plus
Temperature selection
Separate temperatures can be selected for the driver's
and front passenger's sides.
Fig. 114 Display:
Temperature setting
– Turn the rotary control anti-clockwise to reduce the
temperature or clockwise to increase the temperature
⇒ fig. 113.
The temperature setting will be shown on the display of the air
conditioner console. The temperature setting will be shown on the
screen ⇒ fig. 114 for a few seconds if the sound system or MMI* is
switched on.
Applies to vehicles: with deluxe automatic air conditioner plus
Blower 
The automatically selected blower speed can be reduced
or increased manually if required.
Fig. 113 Rotary control
for temperature selection
Fig. 115 Blower
button and rotary
control
document_0900452a81b1b9de.book Seite 105 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
105
Applies to vehicles: with deluxe automatic air conditioner plus
Air recirculation mode 
The air recirculation setting prevents fumes etc. from
entering the interior.
Switching on the air recirculation mode
– Press the  button ⇒
Fig. 116 Display:
Blower setting
.
Switching off the air recirculation mode
– Press the  button again, or
– Press the button for the blower  .
– Turn the rotary control to set the blower to the desired
speed (and regulate the volume of air delivery).
– Press the AUTO button, or
– Press the  button.
The air conditioning system automatically regulates the blower
speed according to the interior temperature. However, you can also
adjust the blower speed manually.
In this setting, the air is drawn from the interior of the vehicle,
filtered and continuously recirculated. We recommend using the air
recirculation mode in the following circumstances:
The blower speed will be shown on the screen ⇒ fig. 116 for a few
seconds if the sound system or MMI* is switched on.
When driving through a tunnel or in queues of traffic, to prevent
fumes entering the interior of the vehicle.
•
WARNING
Note
The blower speed may change automatically. This ensures that
the selected temperature is reached as quickly as possible.
•
The blower speed cannot be regulated separately for the driver
and front passenger sides of the vehicle.
Controls
Safety
Driving tips
For reasons of safety you should not leave the air recirculation
switched on for too long. This mode prevents fresh air from
entering the vehicle, so the windows can mist over if the air
cooling is switched off. Bad visibility can cause an accident.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 106 Donnerstag, 26. Juli 2007 9:16 09
106
Heating and cooling
Switch to AUTO for automatic control of the air distribution.
Applies to vehicles: with deluxe automatic air conditioner plus
Air distribution

The automatically programmed air distribution can be
altered manually if required.
The air distribution setting will be shown on the MMI display
⇒ fig. 118 for a few seconds if the MMI is switched on.
Applies to vehicles: with deluxe automatic air conditioner plus
Defrosting 
The windscreen and side windows are defrosted or
demisted as quickly as possible.
– To switch on, press the  button.
Fig. 117 Air distribution button and rotary
control
– To switch off, press the  button again, or press the
AUTO button.
The temperature is regulated automatically. The air output is
increased to maximum and most of the air comes out of the outlets
below the windscreen.
The air recirculation mode is switched off when the  button is
pressed.
Applies to vehicles: with deluxe automatic air conditioner plus
Heated rear window 
Fig. 118 Display: Air
distribution
– Press the button for Distribution .
– Turn the rotary control to the desired setting.
You can use the air distribution setting to select the air outlets you
wish to activate. In setting  all the air is directed to the windows,
in setting  the air is directed to the driver (or passenger), and in
setting  to the footwells. In addition to this there are several other
possible combinations, allowing you to adjust the air distribution to
suit individual requirements.
The rear window heating helps to demist the rear window.
– Press the  button to switch the rear window heating on
and off.
The rear window heating only works when the engine is running. An
indicator lamp in the button lights up when the rear window heater
is switched on.
Depending on the outside temperature, the rear window heating
switches off automatically after about 10 to 20 minutes.
The rear window heating can be switched on permanently by
pressing the  button for longer than two seconds. It will then
document_0900452a81b1b9de.book Seite 107 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
remain on until the ignition is switched off. When the rear window
heating is switched on, this setting will remain activated for 15
minutes after switching off the ignition.
If the engine is started again during this period of 15 minutes, the
rear window heating will be switched on for about 10 to 20 minutes,
depending on the exterior temperature. This means you do not have
to manually switch on the rear window heating again if the vehicle
has only been parked for a short time.
107
Applies to vehicles: with deluxe automatic air conditioner plus
Air outlets
The air distribution setting directs the air to the outlets
you select.
For the sake of the environment
Switch off the heated rear window manually as soon as the rear
window is clear. By saving electrical power you can also save fuel.
Applies to vehicles: with deluxe automatic air conditioner plus
AC mode AC
Deactivating the AC mode
– Press the AC button.
Activating the AC mode
Fig. 119 Dashboard: Location of air outlets
– Press the AC button again.
In the AC mode, the air cooling system is switched on and the
heating and ventilation are regulated automatically.
Note
If the LED in the AC button should continue to light up when the AC
mode has been switched off (i.e. the air conditioner has been
switched off) this is due to a defect in one of the air conditioner
components. If a malfunction should occur, please contact a qualified workshop.
Controls
Safety
Driving tips
Air outlets
2 and A
3
A
– The outlets can be opened and closed by turning the
thumbwheels next to them.
– The direction of air delivery from these outlets can be
adjusted horizontally and vertically using the adjuster in
the centre of each outlet grille.
The flow of air from the outlets is controlled either automatically or
1 to
manually, depending on the operating mode selected. Outlets A
4 can provide air which is either heated, unheated, or cooled.
A
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 108 Donnerstag, 26. Juli 2007 9:16 09
108
Heating and cooling
Applies to vehicles: with deluxe automatic air conditioner plus
Note
When the air conditioner is operating in the cooling mode, the air is
2 and A
3 . To ensure an adequate cooling
directed mainly to outlets A
effect, you should not close these outlets completely.
Applies to vehicles: with deluxe automatic air conditioner plus
Air outlets for rear passengers
The air outlets for the rear cabin are located in the centre
console.
– The outlets can be opened and closed by turning the
thumbwheels.
– The direction of air delivery from these outlets can be
adjusted horizontally and vertically using the adjuster in
the centre of each outlet grille.
The flow of air from the outlets is controlled either automatically or
manually, depending on the operating mode selected. All the
outlets can provide air which is either heated, unheated, or cooled.
The heater outlets for the rear footwells are located under the front
seats.
Note
When the air conditioner is operating in the cooling mode the air is
directed mainly to the outlets in the centre console. To ensure an
adequate cooling effect, you should not close these outlets
completely.
Economical operation of the air conditioner
Economical operation of the air conditioner will help to
save fuel.
When the air conditioner is operating in the cooling mode it
reduces engine power and increases fuel consumption. To
ensure that the cooling mode is activated only when really
necessary, please note the following points:
– Switch off the cooling mode by pressing the AC button
(LED off) if you wish to save fuel.
– You should also switch off the cooling mode by pressing
the AC button (LED off) if you open the windows or the
tilting panorama roof* while driving.
– If the vehicle has heated up after standing in the sun,
open the windows and doors for a short time to cool the
vehicle.
For the sake of the environment
By saving fuel you also reduce the amount of pollutants emitted
from your vehicle.
document_0900452a81b1b9de.book Seite 109 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
Deluxe automatic air conditioner plus
- basic settings
109
Applies to vehicles: with deluxe automatic air conditioner plus
Automatic recirculation
If the outside air is polluted, an air purity sensor in the
vehicle will automatically switch on the air recirculation.
Applies to vehicles: with deluxe automatic air conditioner plus
General notes
The basic settings for the air conditioner can be adjusted
via the sound system or MMI*.
To prevent fumes, etc. in the outside air from entering the interior,
we recommend that the automatic air recirculation should be
switched on at all times.
If the air purity sensor in the air conditioner system detects a certain
concentration of fumes in the outside air, the control unit will either
pass the incoming air through the pollution filter or automatically
switch on the air recirculation. If there is a high concentration of
pollution in the outside air, the air conditioner automatically
switches to air recirculation and cuts off the supply of air from the
outside. As soon as the level of pollution decreases, air is fed into
the vehicle from the outside again.
Fig. 120 Display:
Setup AC
– Select: Function selector button CAR > control button
AC.
The following functions are available:
•
•
•
•
•
•
•
•
•
•
Automatic air recirculation ⇒ page 109
If the windows mist up when the automatic air recirculation is on,
press the  button immediately.
The automatic air recirculation can switch itself off in certain conditions. If the outside temperature is less than about +10 °C, the automatic air recirculation will only operate for 30 seconds. If the air
conditioner is switched to the ECON mode, or if the outside temperature is less than about -1 °C, the automatic air recirculation will
only operate for 15 seconds.
Synchronisation ⇒ page 109
Auxiliary heating* ⇒ page 110
Applies to vehicles: with deluxe automatic air conditioner plus
Auxiliary ventilation* ⇒ page 110
Synchronisation
Running time* ⇒ page 112
The air conditioner settings can be synchronised for all
passengers.
Timer status* ⇒ page 111
Timer 1* ⇒ page 111
When the synchronisation function is switched on, all subsequent
air conditioner settings made on the driver's side (except for the
seat heating*) are also applied to the front passenger's side.
Timer 2* ⇒ page 111
Timer 3* ⇒ page 111
Supplementary heater* ⇒ page 110
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 110 Donnerstag, 26. Juli 2007 9:16 09
110
Heating and cooling
The synchronisation is cancelled as soon as any adjustments are
made on the front passenger's side.
The auxiliary ventilation  also operates independently of the
engine. This feature can be used to cool the interior with the blower
when the vehicle is left parked in the sun.
Applies to vehicles: with diesel engine
The system will automatically activate either the auxiliary heating or
the auxiliary ventilation mode, depending on the actual temperature measured inside the car and the temperature you have set with
the air conditioner controls. It is possible to alter the temperature
setting while the auxiliary heating/ventilation is running.
Supplementary heater
– Set the Supplementary heater to auto or off.
Models with a diesel engine are equipped with a supplementary
heater to help warm up the interior more quickly. At outside temperatures below about +5 °C the supplementary heater is switched on
(and off) automatically when the engine is running, depending on
the coolant temperature, the temperature in the vehicle interior and
the temperature the heater is set to.
Auxiliary heating and auxiliary
ventilation
Applies to vehicles: with auxiliary heating - under development at the time of printing
Description
The auxiliary heating and ventilation systems heat and
cool the interior independently of the engine.
The auxiliary heating  works in conjunction with the air conditioner system, but does not rely on heat from the engine. Instead of
this, the system burns fuel. The system's main function is to warm
up the interior of the vehicle and to defrost the windows in cold
weather.
The auxiliary heating system can be used both when the vehicle is
stationary and when driving (to provide extra heat while the engine
is warming up).
Switching on and off
There are two different ways of switching on the auxiliary
heating/ventilation system.
•
Immediate start: You can switch the auxiliary heating/ventilation
on and off at any time via the sound system or MMI ⇒ page 111. You
can also switch the system on and off using the remote control
⇒ page 113.
•
Switching on via timer: You can programme various start times
using the timers ⇒ page 111. However you must first activate the
timer before the auxiliary heating/ventilation system will switch on
automatically.
The auxiliary heating/ventilation will switch itself off at the end of
the programmed running time. The running time can be set to 15,
30, 45 or 60 minutes ⇒ page 112.
WARNING
•
The auxiliary heating must not be allowed to run when the
vehicle is in a confined space because it can give off toxic fumes.
•
To avoid any possible fire risk, never have the auxiliary heating
switched on when refuelling the vehicle.
•
Because of the high temperatures which occur when the auxiliary heating is running, make sure when parking the car that the
exhaust outlet under the car is not obstructed in any way and that
the exhaust gases do not come into contact with flammable materials (fire risk).
document_0900452a81b1b9de.book Seite 111 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
•
Note
It is advisable to open the air outlets when using the auxiliary
heating/ventilation.
111
When the auxiliary heating/ventilation is running, you can press the
OFF button on the air conditioner console to switch off the blower
only. Pressing the OFF button a second time will switch on the
blower again.
•
The auxiliary heating/ventilation will not switch on if the fuel in
the tank has reached the reserve zone.
•
The auxiliary heating/ventilation will not switch on if the battery
charge level is low.
• The symbols  (auxiliary ventilation) or  (auxiliary heating)
flash in the instrument cluster next to the clock display when the
auxiliary heating/ventilation is switched on. Both symbols light
continuously when the timer is activated.
•
At low outside temperatures some visible water vapour may
form in the engine compartment. This is a normal phenomenon,
and no reason for concern.
Note
The symbols  (auxiliary ventilation) or  (auxiliary heating) flash in
the instrument cluster next to the clock display when the auxiliary
heating/ventilation is switched on.
Applies to vehicles: with auxiliary heating - under development at the time of printing
Setting and activating the timers
You can make the desired settings for the auxiliary
heating/ventilation on the sound system or MMI*.
Applies to vehicles: with auxiliary heating - under development at the time of printing
Switching on/off immediately
You can switch the auxiliary heating/ventilation on and
off immediately via the sound system or MMI*.
Fig. 122 Display: Timer
Fig. 121 Display:
Setup AC
– Select: Function selector button CAR > control button
AC > Aux. heating or Aux. ventilation.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 112 Donnerstag, 26. Juli 2007 9:16 09
112
Heating and cooling
Applies to vehicles: with auxiliary heating - under development at the time of printing
Setting the running time
You can set the running time on the sound system or
MMI*.
Fig. 123 Display: Timer
status
Setting the timers
– Select: Function selector button CAR > control button
AC > e.g. Timer 1 ⇒ page 111, fig. 122.
Fig. 124 Display:
Running time
Activating a timer
– Select: Function selector button CAR > control button
AC > Timer status ⇒ fig. 123.
– Select: Function selector button CAR > control button
AC > Running time.
Three timers are available for the auxiliary heating/ventilation. You
can set a starting time and running time for each of the timers.
The running time for the auxiliary heating/ventilation can be set to
a time between 15 and 60 minutes. The auxiliary heating/ventilation
will switch itself off at the end of the programmed running time.
When the time set on one of the timers elapses, the date automatically changes to the next day and the Timer status is reset to off. You
have to activate one of the timers (e.g. T1 on) before it will switch on
the auxiliary heating/ventilation at the time you have set. This
prevents the auxiliary heating/ventilation from switching on when
you are not using your vehicle.
Note
Before activating the timer, make sure that the correct time and date
settings have been entered. If the time and/or date are not correct,
the auxiliary heating will come on late or not at all. Please refer to
the MMI Operating Instructions for information on how to set the
date and time.
document_0900452a81b1b9de.book Seite 113 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
Applies to vehicles: with auxiliary heating - under development at the time of printing
Remote control
The auxiliary heating and auxiliary ventilation can also be
switched on or off with the remote control.
113
Changing the battery
– Push back and remove the battery cover on the remote
control ⇒ fig. 126.
– Change the battery. The diagram in the battery compartment shows how the battery should be fitted. The new
battery must be of the same type as the original one.
– Re-fit the battery cover.
When it is switched on, the auxiliary heating or auxiliary ventilation
starts immediately and remains on for the period set in the menu.
The maximum running time is 60 minutes.
Fig. 125 Remote
control for auxiliary
heating
If you want to switch the system on again after the end of the
1 .
programmed running time, press the  button A
Transmitter indicator lamp
3 will flash accordingly to show
The transmitter indicator lamp A
whether the command you sent via the remote control was
successful.
Fig. 126 Remote
control: Changing
battery
Switching on
1 for about 2 seconds to activate the
– Press the  button A
auxiliary heating/ventilation ⇒ fig. 125.
Switching off
2 for about 2 seconds to switch
– Press the OFF button A
off the auxiliary heating/ventilation.
Controls
Safety
Driving tips
1 the
When you switch the system on by pressing the  button A
indicator lamp will flash green for about 30 seconds to confirm that
the heating/ventilation has been switched on. When you switch the
2 the indicator lamp will
system off by pressing the OFF button A
flash red to confirm that the heating/ventilation has been switched
off.
If the remote control is outside the transmitting range the indicator
lamp will flash red slowly. If there is a fault in the system (e.g. fuel
level is down to reserve), the indicator lamp will flash red rapidly. In
both cases the command will not be executed.
When the battery of the remote control is almost completely flat, the
transmitter indicator lamp will not light up and no commands will
be executed.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 114 Donnerstag, 26. Juli 2007 9:16 09
114
Heating and cooling
Transmitting range
The range of the remote control transmitter is about 600 metres.
However, this can be greatly reduced by obstacles (buildings, etc.)
between the remote control transmitter and the vehicle. Hold the
4 upright when using the remote control.
aerial A
You should not normally use the remote control at a distance of less
than 3 metres from the vehicle. If you are closer than this, or if you
use the remote control inside the vehicle, this can cause signal overload.
Fig. 128 Display: Seat
heating/ventilation
Seat heating
For the sake of the environment
Please dispose of old batteries in the proper manner so that they do
not harm the environment.
– Press the control button for Seat heat.  ⇒ fig. 127.
Seat heating
Seat heating/ventilation*
– Turn the rotary control to the desired setting.
– Press the control button for Seat AC  ⇒ fig. 128.
Applies to vehicles: with front seat heating/ventilation
– To adjust the seat ventilation, turn the rotary control anticlockwise to the desired setting.
Seat heating / ventilation
The seat cushions and backrests of the front seats can be
heated and ventilated* electrically.
– To adjust the seat heating, turn the rotary control clockwise to the desired setting.
In setting 0, the seat ventilation and seat heating are switched off.
Caution
To avoid damaging the heating elements of the seat heating, please
do not kneel on the seat or apply sharp pressure at a single point.
Fig. 127 Display: Seat
heating
document_0900452a81b1b9de.book Seite 115 Donnerstag, 26. Juli 2007 9:16 09
Heating and cooling
115
Applies to vehicles: with seat heating for rear seats
Seat heating for rear seats
The seat cushions and backrests of the two outer rear
seats can be heated electrically.
– Turn the left thumbwheel (on the centre console) to
switch on and regulate the heating for the left rear seat.
– Turn the right thumbwheel (on the centre console) to
switch on and regulate the heating for the right rear seat.
The heating is switched off when the thumbwheel is set to 0.
Possible settings range from 1 to 6.
The heating for the rear seats only operates when a sensor registers
the weight of the occupant in the seat. If nobody is travelling on the
rear seats, please switch off the rear seat heating to avoid activating
it unintentionally.
Caution
To avoid damaging the heating elements of the seat heating, please
do not kneel on the seat or apply sharp pressure at a single point.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 116 Donnerstag, 26. Juli 2007 9:16 09
116
Driving
Driving
Steering
Ignition lock
Applies to vehicles: with manually adjustable steering column
Starting the engine with the key
Adjusting the steering wheel position
The height and reach of the steering wheel can be
adjusted as required to suit the driver.
You can use the ignition key to switch on the ignition and
start the engine.
Fig. 130 Ignition key
Fig. 129 Lever beneath
steering column
– Pull the lever ⇒ fig. 129 -arrow- ⇒
– Insert the key into the ignition lock.
up.
– Move the steering wheel to the desired position.
– Manual gearbox: Press the clutch pedal all the way down
and move the gear lever into neutral.
– Then push the lever towards the steering column until
the catch engages.
– Automatic gearbox: Press the brake pedal and move the
selector lever to position P or N.
– Press in the key ⇒ fig. 130 to start the engine.
WARNING
•
Never adjust the position of the steering wheel when the
vehicle is moving - this could cause an accident.
•
For safety reasons, the lever must be pushed securely against
the steering column to prevent the steering wheel from accidentally changing position while driving (accident risk).
– Diesel engines can take a few seconds longer than usual
to start on cold days. Please keep your foot on the clutch
or brake pedal until the engine starts. The glow plug indicator lamp  lights up in the instrument cluster while
the glow plugs are preheating.
document_0900452a81b1b9de.book Seite 117 Donnerstag, 26. Juli 2007 9:16 09
Driving
If you press in the key without pressing the clutch or brake pedal,
the ignition will be switched on or off. The steering lock is released
when the ignition is switched on. Diesel engines continue to be
automatically preheated.
The key can be removed only when the ignition is off. The key has to
be pressed in briefly to switch off the ignition. On vehicles with an
automatic gearbox, the selector lever has to be in position P.
Electrical components with a high power consumption are switched
off temporarily while you start the engine.
When starting from cold the engine may be a little noisy for the first
few seconds until oil pressure has built up in the hydraulic tappets.
This is quite normal and no cause for concern.
If the engine fails to start immediately, the starter will be switched
off automatically after a few seconds. Try to start the engine again.
Driver message in the instrument cluster display
Press brake pedal to start engine
This message appears on vehicles with an automatic gearbox if you
try to start the engine without first pressing the brake pedal.
117
position P you will not be able to lock the vehicle using the exterior
locking switch on the door handle or the remote control key.
Steering lock
The steering is locked when the key is not in the ignition. The
steering lock acts as a theft deterrent.
WARNING
•
Always take the key with you when you leave the vehicle.
Otherwise the engine can be started or power-operated equipment such as the electric windows can be used. This could result
in serious injury.
•
Never leave children or disabled people alone in the car. The
doors could be locked with the remote control key and the occupants could become trapped in the vehicle. The vehicle occupants
could be exposed to extremely high or low temperatures,
depending on the time of year.
•
Never remove the key from the ignition while the vehicle is
moving. The steering lock could engage suddenly, and you would
not be able to steer the car.
Press clutch pedal to start engine
This message appears on vehicles with a manual gearbox if you try
to start the engine without first pressing the clutch pedal.
Engage N or P to start engine
This message will appear if you try to start the engine when the
selector lever of the automatic gearbox is not in P or N.
Shift to P, otherwise vehicle can roll away. Doors do not lock if lever
is not in P. or Please move selector lever to position P. Vehicle
cannot be locked.
For safety reasons, this message will appear and a warning buzzer
will sound if the selector lever of the automatic gearbox is not in
position P after you switch off the ignition. Put the selector lever in
position P; otherwise the vehicle can roll away. If the lever is not in
Controls
Safety
Driving tips
•
Caution
If a malfunction occurs in the electronic ignition lock, a flashing
symbol and the message Ignition lock defective will appear in the
instrument cluster display.
•
Avoid high engine speeds, full throttle and extreme load conditions until the engine has reached its normal operating temperature, otherwise this can damage the engine.
For the sake of the environment
Do not warm up the engine by running it with the car stationary. You
should drive off immediately whenever possible. This will help avoid
unnecessary exhaust emissions.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 118 Donnerstag, 26. Juli 2007 9:16 09
118
Driving
•
Note
If the key should become stuck in the ignition lock, remove the
top part of the key and use it to lock the vehicle.
•
If you open the driver's door while the ignition is switched on, a
warning buzzer will sound, and the message Ignition is on will
appear in the display. In this case, please switch off the ignition.
Switching off the engine
– Stop the vehicle.
– Automatic gearbox: Move the selector lever to position P
or N.
– Press in the ignition key to switch off the engine.
you should leave the engine idling for about 2 minutes before
switching it off.
Note
After the engine is stopped the radiator fan may run on for up to
10 minutes, even if the ignition is switched off. The fan may also
start running again after some time if the coolant temperature rises
due to a build-up of heat, or if the engine is hot and the engine
compartment is heated up further by direct sunlight.
Starting and stopping the engine
with the advanced key
Applies to vehicles: with advanced key
Emergency Off function
Starting the engine with the Start/Stop
button
If necessary in an emergency, the engine can be switched off while
the vehicle is still moving. The engine will be switched off if you
press and hold the ignition key.
You can use the Start/Stop button to switch on the ignition and start the engine.
WARNING
•
•
Never switch off the engine until the vehicle is stationary.
The brake servo and the power steering system work only
when the engine is running. You need more strength to steer and
brake the vehicle when the engine is switched off. This would
mean a greater risk of accidents and serious injury, because you
cannot steer and brake in the normal manner.
Caution
If the engine has been working hard for a long time, there is a risk
of heat building up in the engine compartment after the engine has
been switched off; this could cause engine damage. For this reason,
Fig. 131 Audi
advanced key: START
ENGINE STOP button
– Manual gearbox: Press the clutch pedal all the way down
and move the gear lever into neutral.
document_0900452a81b1b9de.book Seite 119 Donnerstag, 26. Juli 2007 9:16 09
Driving
– Automatic gearbox: Press the brake pedal and move the
selector lever to position P or N ⇒
.
– Press the Start/Stop button ⇒ page 118, fig. 131 to start
the engine.
– Diesel engines can take a few seconds longer than usual
to start on cold days. Please keep your foot on the clutch
or brake pedal until the engine starts. The glow plug indicator lamp  lights up in the instrument cluster while
the glow plugs are preheating.
If you press the Start/Stop button without pressing the clutch or
brake pedal, the ignition will be switched on (and will be switched
off if you press the button again). Diesel engines are preheated
when the ignition is switched on.
If the engine fails to start straight-away, switch off the starter after
about 10 seconds and try again after about half a minute.
When starting from cold the engine may be a little noisy for the first
few seconds until oil pressure has built up in the hydraulic tappets.
This is quite normal and no cause for concern.
Driver message in the instrument cluster display
No key identified
This message appears when you press the Start/Stop button if there
is no remote control key inside the vehicle or if the system cannot
detect or identify the key. This can happen, for example, if the radio
signal from the key is obstructed by a metal briefcase or similar.
Electronic equipment, such as mobile phones, can also interfere
with the radio signal from the key.
119
Press clutch pedal to start engine
This message appears on manual vehicles if you press the
Start/Stop button to start the engine without first pressing the
clutch pedal. The engine will only start if you press the clutch pedal.
Engage N or P to start engine
This message will appear if you try to start the engine when the
selector lever of the automatic gearbox is not in P or N. The engine
can only be started if the selector lever is in one of these positions.
Key not in vehicle
This message will appear together with the symbol  if the remote
control key is removed from the vehicle while the engine is running.
This is to remind you not to continue driving without the key (for
example if you change drivers).
If the remote control key is not in the vehicle you will not be able to
switch on the ignition or restart the engine after it has been
switched off. Without the key, you will also not be able to lock the
vehicle from the outside.
Shift to P, otherwise vehicle can roll away. Doors do not lock if lever
is not in P. or Please move selector lever to position P. Vehicle
cannot be locked.
For safety reasons, this message will appear and a warning buzzer
will sound if the selector lever of the automatic gearbox is not in
position P when you switch off the ignition with the Start/Stop
button. Put the selector lever in position P; otherwise the vehicle
can roll away. If the lever is not in position P you will not be able to
lock the vehicle using the exterior locking switch on the door handle
or the remote control key.
Advanced key defective! Use ignition lock
Press brake pedal to start engine
This message appears on automatic vehicles if you press the
Start/Stop button to start the engine without first pressing the
brake pedal. The engine will only start if you press the brake pedal.
Controls
Safety
Driving tips
This message appears if the vehicle has to be started with the ignition key instead of the Start/Stop button.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 120 Donnerstag, 26. Juli 2007 9:16 09
120
Driving
Steering lock
The steering is locked if the key is not in the ignition and the driver
door has been opened. The steering lock acts as a theft deterrent.
Switching off the engine with the Start/Stop
button
– Stop the vehicle.
WARNING
Never run the engine in confined spaces. The exhaust gases are
toxic.
•
•
Emergency Off function
Should it be necessary in an emergency, the engine can be switched
off when the selector lever is in position R, D or S. To switch off the
engine (max. speed 10 km/h) press and hold the Start/Stop button
and keep your foot on the brake.
WARNING
Caution
Avoid high engine speeds, full throttle and extreme load conditions until the engine has reached its normal operating temperature, otherwise this can damage the engine.
•
•
– Press the Start/Stop button ⇒ page 118, fig. 131.
Never switch off the engine until the vehicle is stationary.
The brake servo and the power steering system work only
when the engine is running. You need more strength to steer and
brake the vehicle when the engine is switched off. This would
mean a greater risk of accidents and serious injury, because you
cannot steer and brake in the normal manner.
•
– Automatic gearbox: Move the selector lever to position P
or N.
The engine cannot be started by push-starting or towing.
If the engine has been working hard for a long time, there is a risk
of heat building up in the engine compartment after the engine has
been switched off; this could cause engine damage. For this reason,
you should leave the engine idling for about 2 minutes before
switching it off.
Note
If you open the driver's door while the ignition is switched on, a
warning buzzer will sound, and the message Ignition is on will
appear in the display. In this case, please switch off the ignition.
•
•
Never switch off the engine until the vehicle is stationary.
The brake servo and the power steering system work only
when the engine is running. You need more strength to steer and
brake the vehicle when the engine is switched off. This would
mean a greater risk of accidents and serious injury, because you
cannot steer and brake in the normal manner.
Caution
If the engine has been working hard for a long time, there is a risk
of heat building up in the engine compartment after the engine has
been switched off; this could cause engine damage. For this reason,
you should leave the engine idling for about 2 minutes before
switching it off.
Note
After the engine is stopped the radiator fan may run on for up to
10 minutes, even if the ignition is switched off. The fan may also
document_0900452a81b1b9de.book Seite 121 Donnerstag, 26. Juli 2007 9:16 09
Driving
start running again after some time if the coolant temperature rises
due to a build-up of heat, or if the engine is hot and the engine
compartment is heated up further by direct sunlight.
Electro-mechanical parking brake
Operation
The electro-mechanical parking brake replaces the handbrake.
121
When driving away
•
The parking brake auto release function releases the parking
brake automatically when you wish to start moving ⇒ page 122,
“Driving away from a standstill”.
•
When driving away on a gradient, the parking brake auto release
function prevents the vehicle from rolling back unintentionally. The
braking force of the parking brake is only released when there is
enough power at the wheels to make the vehicle move in the desired
direction.
Emergency braking function
An emergency braking function enables you to stop the vehicle even
if the conventional foot brake should fail to work ⇒ page 123,
“Emergency braking function”.
Warning and indicator lamps
•
The warning lamps  in the instrument cluster and in the switch
light up when the parking brake is applied with the ignition
switched on.
Fig. 132 Centre
console: Parking brake
A ⇒ fig. 132 to apply the parking brake. The
– Pull switch A
indicator lamp in the switch will light up.
– Depress the brake or accelerator pedal and press the
switch at the same time to release the parking brake. The
indicator lamp in the switch will go out.
Your vehicle is equipped with an electro-mechanical parking brake.
The parking brake replaces the conventional handbrake, and is
mainly intended to prevent the vehicle from rolling away accidentally.
However, the electro-mechanical parking brake also offers a number
of convenience and safety features in addition to the functions of a
normal handbrake.
Controls
Safety
Driving tips
•
The warning lamps  in the instrument cluster and switch light
up for approximately 20 seconds when the parking brake is applied
with the ignition switched off.
WARNING
Never press the accelerator pedal or release the clutch inadvertently if a gear is engaged or if the selector lever is not in position
P or N (on automatic vehicles) while the vehicle is stationary with
the engine running. The vehicle could otherwise start moving
immediately and possibly cause an accident.
Caution
If the symbol  flashes in the centre display, or if the warning lamp
 flashes in the instrument cluster, there is a fault in the brake
system. You can press the SET button to obtain a message
explaining the fault. If the message Parking brake! appears, there is
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 122 Donnerstag, 26. Juli 2007 9:16 09
122
Driving
a fault in the parking brake. Have the fault repaired by a qualified
workshop without delay ⇒ page 32.
WARNING
•
•
Note
The parking brake can be applied at any time - even when the
ignition is switched off. However, the ignition must be switched on
before the parking brake can be released.
•
Any slight noise which may be heard when the parking brake is
applied or released is quite normal and no cause for concern.
•
The parking brake runs an automatic test cycle at regular intervals when the vehicle is parked. This may also cause a slight noise,
which is normal.
Always take the key with you when leaving the vehicle – even
if you only intend to be gone for a short time. This is especially
important if children are left in the car. They might otherwise be
able to start the engine, release the parking brake or use poweroperated equipment such as the electric windows - this could lead
to injuries.
•
Do not leave anyone (especially children) in the vehicle when it
is locked. Locked doors could delay assistance in an emergency,
potentially putting lives at risk.
Driving away from a standstill
Parking
Please note the following points to ensure there is no risk
of the car rolling away accidentally after it is parked.
The parking brake auto release function releases the
parking brake automatically when you wish to start
moving.
Applying the parking brake when stopping
Parking the car
– Use the foot brake to stop the vehicle.
– Pull the switch to apply the parking brake.
– Pull the switch to apply the parking brake.
Releasing the parking brake when driving away
– Automatic gearbox: Move the selector lever to P.
– Drive off in the normal way: the parking brake will be
released automatically and the vehicle will start moving.
– Switch off the engine ⇒
.
– Manual gearbox: Engage the first gear.
When parking on slopes
– Turn the steering wheel so that the vehicle would roll into
the kerb if it did start to move accidentally.
On vehicles with automatic gearbox, you can apply the parking
brake when stopping at traffic lights, etc. Then you do not have to
hold the car with the footbrake, as the parking brake will stop it
creeping forward while a gear is engaged in the automatic transmission. When you drive off in the normal way, the parking brake will be
released automatically and the vehicle will start moving.
Driving away on a slope
When driving away on a gradient, the parking brake auto release
function prevents the vehicle from rolling back unintentionally. The
document_0900452a81b1b9de.book Seite 123 Donnerstag, 26. Juli 2007 9:16 09
Driving
braking force of the parking brake is only released when there is
enough power at the wheels to make the vehicle move in the desired
direction.
Note
For safety reasons the parking brake will only release automatically
if the driver's seat belt is engaged in its buckle.
123
If you pull out and hold the parking brake switch at a road speed
above about 8 km/h, this will initiate an emergency brake application. The brakes are then applied hydraulically at all four wheels.
The effect is the same as an emergency stop (full brake application)
⇒
To prevent the emergency braking function from being used accidentally, a warning buzzer sounds when the switch is operated. The
brakes are released immediately when you release the switch or
press down the accelerator.
Driving away when towing a trailer
Please note the following points to prevent the vehicle
from rolling back unintentionally on a gradient.
– Pull and hold the parking brake switch and press the
accelerator. The parking brake will remain engaged and
prevent any tendency to roll back down the slope.
– You can release the parking brake switch as soon as the
engine is delivering enough power to the wheels.
Depending on the weight of the vehicle and trailer and the steepness of the slope, there may be a tendency to roll back downhill
when driving away from a standstill. You can prevent this by pulling
out the parking brake switch as you press the accelerator (in the
same way as with a conventional handbrake).
WARNING
You should only use the emergency braking function in a real
emergency, for example if the brake system should fail or if the
brake pedal is obstructed. If you use the emergency braking function by activating the parking brake switch, the effect is similar to
a full brake application (emergency stop). Please remember that
the ESP (with its combined ABS, EDL and traction control functions) is still subject to certain physical limits. In a corner or in bad
road or weather conditions an emergency stop can cause the
vehicle to skid or lose steering control.
Driver messages in the instrument cluster
display
Caution: Vehicle parked too steep
Emergency braking function
This feature enables you to stop the vehicle if the main
brake system should fail or if the pedal is obstructed.
This message can appear when you apply the parking brake if the
car is parked on a gradient steeper than about 30%.
In this case the parking brake may not be strong enough to prevent
the vehicle from rolling back accidentally.
– Pull out and hold the parking brake switch to stop the
vehicle with the parking brake in an emergency.
Please release parking brake
– The brakes will be released immediately if you release the
switch or press down the accelerator.
However, please remember that, for safety reasons, the parking
brake will only release automatically if the driver's seat belt is
buckled.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 124 Donnerstag, 26. Juli 2007 9:16 09
124
Driving
Press brake pedal to release parking brake
This message may appear when you press the switch to release the
parking brake. The parking brake can only be released, if you
depress the brake pedal and simultaneously press the switch or if
you use the parking brake auto release function ⇒ page 122.
When the Audi hold assist function is on, the vehicle is automatically prevented from rolling away and you no longer
have to keep your foot on the brake pedal.
Conditions for switching on Audi hold assist
 Parking brake malfunction !
– The driver's door must be closed.
This message will appear together with the yellow symbol  if a
malfunction should occur in the parking brake.
– The driver's seat belt must be buckled.
– The engine must be running.
Fault in parking brake auto release
This driver message will appear in the event of a malfunction of the
parking brake auto release. The automatic release of the parking
brake when moving off from a standstill is not functioning correctly.
The parking brake must be released manually by pressing the
switch. Have the fault rectified by a qualified workshop.
Switching on Audi hold assist
B ⇒ fig. 133 in the centre console to switch
– Press button A
on the Audi hold assist function. The indicator lamp in
the switch will light up.
Switching off Audi hold assist
Applies to vehicles: with Audi hold assist
Audi hold assist
Audi hold assist helps the driver when the vehicle is
stationary and automatically prevents the vehicle from
rolling away when driving off.
Fig. 133 Detail of the
centre console: Button
for Audi hold assist
B ⇒ fig. 133 to switch off the Audi hold
– Press button A
assist function. The indicator lamp in the switch will go
out.
B while the vehicle is being held by
– If you press button A
the Audi hold assist function, the electro-mechanical
parking brake  will automatically take over. The
parking brake will not take over if the foot brake is
applied simultaneously.
– Audi hold assist is switched off automatically if you open
the driver's door, unbuckle the seat belt or switch off the
engine. If this happens when the green symbol  is
displayed in the instrument cluster, the parking brake
will be applied automatically to ensure that the vehicle is
parked safely.
Audi hold assist helps the driver to keep the vehicle stationary while
the engine is running, for instance on steep gradients, at traffic
document_0900452a81b1b9de.book Seite 125 Donnerstag, 26. Juli 2007 9:16 09
Driving
lights or in stop-and-go traffic. When the Audi hold assist function
is on, you don't have to keep your foot on the brake to prevent the
vehicle from accidentally rolling away. Once it detects that the
vehicle is stopped, Audi hold assist keeps the vehicle stationary. The
green symbol  in the instrument cluster indicates that the function is activated. You can now take your foot off the brake pedal.
As soon as you drive off in the normal way, the parking brake will
automatically be released and the vehicle will start moving.
If the conditions for Audi hold assist change and the function is
switched off as a result, the parking brake will be applied automatically to ensure that the vehicle is parked safely. The diode in the
button will go out when the Audi hold assist function is switched
off.
•
125
Note
Audi hold assist can be switched on only when the driver's door
is closed, the driver's seat belt is buckled and the engine is running.
•
Audi hold assist prevents automatic vehicles from creeping
forwards when the brake pedal is released with the car in gear.
•
When the vehicle has been stationary for an extended period,
Audi hold assist will automatically apply the parking brake. In this
case, the green symbol  in the instrument cluster display will
change to red .
Cruise control system
Applies to vehicles: with cruise control system
WARNING
Switching on
The intelligent technology in Audi hold assist cannot defy the laws
of physics. Do not let the extra convenience provided by Audi hold
assist tempt you into taking a safety risk.
The cruise control system allows you to drive at a
constant speed of 30 km/h or higher.
•
Audi hold assist cannot keep the vehicle stationary in all conditions on a gradient (e.g. if the road is slippery or icy).
•
Audi hold assist must be switched on again each time the
engine is started – Risk of accident!
•
Never get out of the vehicle when the engine is running and
Audi hold assist is switched on – Risk of accident!
•
Always ensure that the vehicle is stopped properly and safely
to avoid injury to yourself and others.
Fig. 134 Control lever
and pushbutton
Caution
Switch off the Audi hold assist function before driving the vehicle
into a car wash.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 126 Donnerstag, 26. Juli 2007 9:16 09
126
Driving
WARNING (continued)
•
When you take a turn-off, drive along a motorway exit lane or
pass through roadwork sections, please temporarily switch off the
cruise control system.
•
Please make sure you do not unintentionally rest your foot on
the accelerator - this will override the cruise control system which,
as a result, will not brake the vehicle.
Fig. 135 Display:
Selected speed
A to position
– Pull the lever A
switch on the system.
1 ⇒ page 125, fig. 134 to
A
– Drive at the speed you wish to set the system to.
– Press the button marked
B to store the speed.
A
The display will indicate the stored speed, and the green symbol 
will appear ⇒ fig. 135. The display can vary according to the display
status. In addition, the indicator lamp  in the instrument cluster
will light up.
A constant speed is maintained by adjusting the engine power or
braking the vehicle accordingly.
WARNING
•
Always direct your full attention to the road, even when you are
using the cruise control system. It is always the driver who is
responsible for determining the speed and for keeping a safe
distance to the other vehicles on the road.
•
For safety reasons, the cruise control system must not be used
in city traffic, stop-and-go traffic, roads with a lot of bends or in
difficult driving conditions (such as ice, fog, loose grit or gravel,
heavy rain, aquaplaning) - this could cause an accident!
•
Note
Vehicles with manual gearbox: The set speed cannot be reached
if the currently selected gear is too high or too low. Change down to
a lower gear if the engine is no longer running smoothly or change
up a gear to avoid overrevving the engine.
•
The brake lights come on when the system brakes the vehicle.
Applies to vehicles: with cruise control system
Adjusting the speed
A up towards A
+ or down towards A
– Push the lever A
⇒ page 125, fig. 134 in order to increase or reduce the
cruising speed setting.
– Release the lever to store the current cruising speed.
You can alter the set speed in steps of 1 km/h by briefly pressing the
lever upwards or downwards. When you press and hold the lever,
the speed is changed in steps of 10 km/h.
You can still use the accelerator pedal to increase speed in the
normal way, for example to overtake another vehicle. Once you
release the accelerator, the system will revert to the speed you
stored initially.
However, if the vehicle exceeds the programmed speed by more
than 10 km/h for more than 5 minutes, the cruise control system will
document_0900452a81b1b9de.book Seite 127 Donnerstag, 26. Juli 2007 9:16 09
Driving
be deactivated temporarily. The green symbol in the display will
change to white but the stored speed will be retained.
– Drive more than 10 km/h faster than the stored speed
over a period of more than 5 minutes.
Applies to vehicles: with cruise control system
Switching off completely
Pre-selecting a speed
– Press the lever
You can pre-select a desired speed while the vehicle is
stationary.
– Switch off the ignition.
– Switch on the ignition.
A to position 1 ⇒ page 125, fig. 134.
A
+ or down towards A
- in
Push the lever up towards A
– Pull the lever
–
order to increase or reduce the cruising speed setting.
– Release the lever to store the cruising speed setting
displayed.
127
A to position A
2 (click stop engaged), or
A
The speed setting will remain stored after the system is temporarily
deactivated. To resume the programmed cruising speed, release the
1 .
clutch or brake pedal and pull the lever to position A
The stored speed will be deleted once the ignition is switched off.
WARNING
Do not resume the programmed cruising speed if this is too high
for the traffic conditions - this can cause accidents.
This function allows you to enter the desired cruise control setting
speed ahead of time, for example before joining a motorway. Once
you are on the motorway, you can activate the cruise control system
1 .
by pulling the lever to position A
Applies to vehicles: with cruise control system
Switching off the cruise control system
Switching off temporarily
– Press the brake pedal, or
– Manual gearbox: Press the clutch pedal for a relatively
long period, or
A to position A
2 (click stop not engaged)
– Push lever A
⇒ page 125, fig. 134, or
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 128 Donnerstag, 26. Juli 2007 9:16 09
128
adaptive cruise control (ACC)
adaptive cruise control (ACC)
Speed and distance control system
Driver messages
Applies to vehicles: with adaptive cruise control
When the system is being used, important information is displayed
in the speedometer and on the instrument cluster display screen
⇒ page 134, “Driver messages”.
Description
The adaptive cruise control is a combined speed and
distance control system to assist the driver.
Please note the following points:
The adaptive cruise control has certain limits determined by the
system itself. This means that the driver may in some situations
have to intervene and control the speed and distance to the vehicle
in front himself ⇒ page 138, “Driver intervention prompt” and
⇒ page 140, “System limitations”.
WARNING
Fig. 136 Trim grille
(front right): Position of
radar sensor
Adaptive cruise control allows you to maintain any desired constant
speed between 30 and 200 km/h. In addition, the system controls
the distance maintained to the vehicle in front (subject to certain
limitations as described below).
The system can be used to greatest effect on long motorway journeys or on other main roads with long straight sections.
How is the system operated?
The adaptive cruise control system is operated via a control lever on
the steering wheel ⇒ page 131, “Setting the speed” and
⇒ page 133, “Setting the distance”.
Please always direct your full attention to the road, even when you
are using adaptive cruise control. It is always the driver who is
responsible for determining the speed and for keeping a safe
distance to the other vehicles on the road.
•
For safety reasons, the adaptive cruise control must not be
used in city traffic, stop-go traffic, roads with a lot of bends or in
difficult driving conditions (such as ice, fog, loose grit or gravel,
heavy rain, aquaplaning) - this could cause an accident!
•
When you take a turn-off, drive along a motorway exit lane or
pass through roadwork sections, please temporarily switch off the
adaptive cruise control in order to avoid the vehicle accelerating to
the selected speed.
•
The adaptive cruise control can only control the distance to
vehicles in front. As a rule, it cannot recognize vehicles travelling
in other lanes. For this reason, please temporarily switch off the
system if you are travelling in the inside lane and vehicles in the
overtaking lane are travelling at a slower speed than you are.
Otherwise, you would overtake these vehicles on the inside.
document_0900452a81b1b9de.book Seite 129 Donnerstag, 26. Juli 2007 9:16 09
adaptive cruise control (ACC)
129
Applies to vehicles: with adaptive cruise control and manual gearbox
WARNING (continued)
Vehicles with manual gearbox
•
Adaptive cruise control will not react when approaching a
stationary obstacle, e.g. the end of a traffic jam or a broken-down
vehicle, or if a vehicle should come towards you in the same lane.
•
Please make sure you do not unintentionally rest your foot on
the accelerator - this will override the adaptive cruise control
system which, as a result, will not automatically brake the vehicle.
•
Note
For safety reasons, the speed setting will be deleted when the
ignition is switched off.
•
Switching on the adaptive cruise control automatically activates
the Electronic Stabilisation Program (ESP) and the traction control
system (ASR). These two systems cannot be deactivated while the
adaptive cruise control is switched on.
•
Damage caused by impacts (e.g. if the vehicle is damaged when
parking) can affect the radar sensor settings. This can cause the
system to malfunction or switch off completely.
The driver of a vehicle with a manual gearbox of course
has to change gears as appropriate, even when the adaptive cruise control is activated.
The adaptive cruise control is available from the second to the sixth
gear (when driven in normal engine speed range).
When the adaptive cruise control is activated, the driver must press
the clutch pedal as normal in order to change gear. When changing
gear or pressing the clutch pedal (for up to 20 seconds), the adaptive cruise control will remain activated.
When changing gear, the driver does not have to accelerate after
engaging a gear as the engine torque will be coordinated by the
adaptive cruise control.
The following situations may lead to an automatic deactivation of
the adaptive cruise control:
•
pressing the clutch pedal too long (longer than approx.
20 seconds)
•
•
•
•
The radar sensor is heated. However, in winter conditions, you
should make sure that the radar sensor is free of ice and snow
before you set off. If necessary, carefully clean the cover of the radar
sensor and the surrounding area ⇒ page 128, fig. 136.
To make sure that the radar sensor is fully operative, do not
attach any objects (e.g. stickers, add-on parts or other accessories)
to the area surrounding the radar sensor. Do not paint the area
surrounding the radar sensor.
Controls
Safety
Driving tips
incorrect changing of gears and/or use of the clutch pedal
Note
The adaptive cruise control cannot be activated while changing
gears.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 130 Donnerstag, 26. Juli 2007 9:16 09
130
adaptive cruise control (ACC)
How does the distance control work?
If the vehicle in front accelerates, the adaptive cruise control will
also accelerate, up to the target speed you have specified.
Vehicles in front are detected by a radar sensor.
Driver intervention prompt
Applies to vehicles: with adaptive cruise control
In some situations, it is necessary for the driver to brake the vehicle
with the foot brake in order to keep a safe distance to the vehicle in
front or to avoid a collision. In this case, a warning message will
appear in the display and you will also hear a warning tone
⇒ page 138.
When overtaking
Fig. 137 Area covered
by radar sensor
When you move into the overtaking lane and no vehicle is detected
in front, the adaptive cruise control will accelerate up to the target
speed and then maintain it.
Overriding
The adaptive cruise control uses a radar sensor ⇒ fig. 137 which is
integrated in the front of the vehicle and is subject to certain system
limitations ⇒ page 140. Stationary objects are disregarded. The
system requires reflecting surfaces in order to be able to measure
the distance. If the ACC is unable to measure the distance it will not
respond.
No vehicle in front
When there is no vehicle in front, the adaptive cruise control works
like a speed control system. It maintains a constant target speed
specified by the driver.
Vehicle in front
If you catch up with a vehicle driving in front, the adaptive cruise
control will reduce the speed accordingly (within the limits set by
the system ⇒ page 138, “Driver intervention prompt” and
⇒ page 140, “System limitations”) and adapt it to the speed of the
vehicle in front. Then the system will try to adjust the distance to the
car in front according to the settings selected. During the adjustment process the system may temporarily not be able to adhere to
the distance you had specified ⇒
in “Description” on page 128.
You can still use the accelerator pedal at any time to increase speed
in the normal way. The previously programmed speed will be
resumed when the accelerator pedal is released.
•
Note
Please note that acceleration will vary depending on the preset
programme. If you have, for example, selected “Distance 1” and the
driving programme “dynamic”, acceleration will be more "sporty".
However, if you have set the system to “Distance 4” and driving
programme “comfort”, acceleration will be more gradual. For a
detailed description please refer to ⇒ page 133, “Setting the
distance”.
•
No vehicle in front, Vehicle in front and a Driver intervention
prompt will be indicated by an indicator lamp ⇒ page 134, “Indicator lamp and display in the speedometer”.
document_0900452a81b1b9de.book Seite 131 Donnerstag, 26. Juli 2007 9:16 09
adaptive cruise control (ACC)
131
– Drive at the desired speed. The speed must be in the
range between 30 and 200 km/h.
Applies to vehicles: with adaptive cruise control
Switching the system on and off
– Press the SET button -arrow- ⇒ fig. 139 to confirm the
target speed you wish to store.
When the SET button is released, the current speed is stored in the
memory and the vehicle will then maintain this speed.
Fig. 138 Control lever
for: Switching the
system on and off
– Pull the control lever to position
on the system.
1 ⇒ fig. 138 to switch
A
2 (click stop engaged)
– Press the control lever to position A
to switch the system off.
One or two red diodes will light up in the speedometer dial
⇒ page 134 to mark the speed which is currently stored in the
system. At the same time, the speed will briefly be displayed in the
system status indicator ⇒ page 136.
Note
For safety reasons, the speed setting will be deleted when the ignition is switched off.
Applies to vehicles: with adaptive cruise control
Setting a new speed
Applies to vehicles: with adaptive cruise control
The speed can be altered without touching the accelerator or the brake.
Setting the speed
Fig. 140 Control lever
for: Setting a new
speed
Fig. 139 Control lever
for: Setting speed
Important: The system must be switched on.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 132 Donnerstag, 26. Juli 2007 9:16 09
132
adaptive cruise control (ACC)
Setting a higher speed
Applies to vehicles: with adaptive cruise control
– Briefly move the control lever up towards A ⇒ fig. 140.
The speed will be incremented by one graduation on the
scale in the speedometer.
+
+ and hold it in this
– Press the control lever up towards A
position. The speed setting is indicated by the diodes in
the speedometer; the speed will be increased accordingly.
Switching off the system (with speed
memory function) and reactivating it
In some situations it makes sense to switch off the
system.
Setting a lower speed
- . The
– Briefly move the control lever down towards A
speed will be reduced by one graduation on the scale in
the speedometer.
- and hold it in
– Press the control lever down towards A
this position. The speed setting is indicated by the
diodes in the speedometer; the speed will be reduced
accordingly.
After releasing the control lever, the system will adapt your speed to
the setting you have selected.
Following any changes, the new stored speed will be displayed
briefly in the system status indicator ⇒ page 136.
Fig. 141 Control lever
for: Switching off the
system (with speed
memory function) and
reactivating it
Switching off the system (with speed memory
function)
– Press the brake pedal, or
2 ⇒ fig. 141.
– Press the control lever in direction A
Reactivating the system
1 .
– Release the brake pedal and pull the lever in direction A
Note
You can still use the accelerator pedal at any time to increase speed
in the normal way. The previously programmed speed will be
resumed when the accelerator pedal is released. You can set a new
speed at any time by pressing the SET button ⇒ page 131,
fig. 139.
WARNING
It is dangerous to resume a set speed which is too high for the
current road, traffic or weather conditions - risk of accident.
Note
When switching off the system (with speed memory function) the
speed stored at this point remains in the memory.
document_0900452a81b1b9de.book Seite 133 Donnerstag, 26. Juli 2007 9:16 09
adaptive cruise control (ACC)
•
Applies to vehicles: with adaptive cruise control
Setting the distance
A distance of 36 metres at a speed of 130 km/h
Distance 2
The distance can be set in 4 different stages.

This setting is suitable for relaxed “moving with the flow” in a line
of traffic. The time interval is 1.3 seconds. This is equivalent to (for
instance):
•
•
A distance of 18 metres at a speed of 50 km/h
A distance of 47 metres at a speed of 130 km/h
Distance 3
Fig. 142 Control lever
for: Setting the
distance
– Briefly press the sliding switch ⇒ fig. 142 once towards
+ or A
- . The display in the instrument cluster will briefly
A
show the current distance setting.
+ or A
- to
– Press the sliding switch again towards A
increase or reduce the distance by one level at a time.
Choosing the distance
The adaptive cruise control system determines the distance to the
vehicle in front by time intervals. It defines a time-based distance to
the vehicle in front which is kept at a constant level. This converts
to a distance which depends on the speed - the higher the speed,
the higher the safety distance in metres ⇒
.
The actual distance maintained by the adaptive cruise control can
be longer or shorter, depending on the traffic situation and the
driving style of the driver in front.

This (recommended) setting is suitable for relaxed “moving with the
flow” in a line of traffic. The time interval is 1.8 seconds. This is
equivalent to (for instance):
•
•
A distance of 25 metres at a speed of 50 km/h
A distance of 65 metres at a speed of 130 km/h
Distance 4

This setting is suitable for single-carriageway roads. The time
interval is 2.3 seconds. This is equivalent to (for instance):
•
•
A distance of 32 metres at a speed of 50 km/h
A distance of 83 metres at a speed of 130 km/h
You can control the acceleration and braking response of your
vehicle in adaptive cruise control mode by adjusting the settings on
the sound system or MMI* ⇒ page 139. Depending on the driving
program and distance selected, acceleration and braking response
will range from dynamic (1) to relaxed (5).
dynamic
standard
comfort
Distance 1
1
2
3
Distance 2
2
3
4
This setting is suitable for brisk driving in a line of traffic. The time
interval is 1 second. This is equivalent to (for instance):
Distance 3
2
3
4
•
Distance 4
3
4
5
Distance 1

A distance of 14 metres at a speed of 50 km/h
Controls
Safety
133
Driving tips
Driving program
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 134 Donnerstag, 26. Juli 2007 9:16 09
134
adaptive cruise control (ACC)
A Indicator lamp and speedometer display
A
WARNING
When setting the distance, the driver is responsible for adhering
to the laws and regulations which apply in the country he is travelling in.
A of the display shows important information regarding
Section A
the use of the adaptive cruise control system. The target speed you
have set is marked by diodes in the speedometer.
The indicator lamp shows whether the system has detected a
vehicle in front.
Driver messages
B Instrument cluster display
A
Applies to vehicles: with adaptive cruise control
You can call up the display for the adaptive cruise control by repeatedly pressing the RESET button on the windscreen wiper lever. For
more details refer to ⇒ page 27.
Messages in the instrument cluster
The instrument cluster displays various driver messages.
C System status indicator
A
C of the display is not shown permaThe information in section A
nently. It only appears if you, for example, set or change the speed
setting, change the time interval, when messages are displayed, or
if the adaptive cruise control is switched off for safety reasons.
Applies to vehicles: with adaptive cruise control
Indicator lamp and display in the
speedometer
Fig. 143 Overview of instrument cluster
A Indicator lamp and speedometer display
A
B Instrument cluster display
A
C System status indicator
A
Fig. 144 Instrument
cluster: Indicator lamp
document_0900452a81b1b9de.book Seite 135 Donnerstag, 26. Juli 2007 9:16 09
adaptive cruise control (ACC)
Target speed
Applies to vehicles: with adaptive cruise control
The target speed set by the driver is indicated by a red diode in the
speedometer.
Instrument cluster display
135
If the speed setting is between two graduations on the speedometer dial, the two closest diodes will both light up ⇒ fig. 143.
It is only possible to set target speeds ranging from 30 to 200 km/h.
This speed range is illuminated slightly by the diodes on the speedometer dial.
Indicator lamp (symbol)
A No vehicle in front: The green indicator lamp A
A ⇒ page 134,
• A
fig. 144 shows that the adaptive cruise control system is in cruise
mode and that there is no vehicle in front. It maintains the stored
target speed.
B Vehicle in front: The green indicator lamp A
B shows that the
• A
system has detected a vehicle in front. The speed is adapted to the
vehicle in front. The adaptive cruise control system accelerates and
brakes the vehicle automatically.
C Driver intervention prompt: When the red indicator lamp
• A
C , this is a warning for the driver to intervene. The driver
flashes A
has to brake the vehicle with the foot brake. This warning lamp will
always appear when the adaptive cruise control system alone is not
able to brake the vehicle sufficiently to maintain a safe distance to
a vehicle in front. An audible alarm (warning tone) will also sound
when the lamp starts to flash. For further information on the driver
intervention prompt ⇒ page 138.
•
Note
If you exceed the target speed by using the accelerator, the
driver intervention prompt will not be accompanied by a warning
tone. The indicator lamp shown in the speedometer will also switch
off if the target speed is exceeded.
•
You can change the volume of the warning tone on the sound
system or MMI* ⇒ page 139, “Setting the warning tone volume and
driving program”.
Controls
Safety
Driving tips
Fig. 145 Instrument
cluster: Display
Repeatedly press the RESET button on the windscreen wiper lever
to select whether you wish to display information regarding the onboard computer, the navigation system* or the adaptive cruise
control in this section of the display screen.
A Vehicle image
A
B Distance
A
C System status
A
A Vehicle image
A
The vehicle image will show you whether the system has detected a
vehicle in front.
•
•
•
Vehicle outlined: No vehicle in front
Vehicle in white: A vehicle in front has been detected
Vehicle in red: Driver intervention prompt
B Distance
A
The arrows and scale indicate the distance to the vehicle in front.
•
No vehicle in front: If there is no vehicle in front, no arrows will
be shown.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 136 Donnerstag, 26. Juli 2007 9:16 09
136
adaptive cruise control (ACC)
•
Vehicle in front: If a vehicle is detected in front, the arrows will be
on the scale. The green area of the scale represents the distance
setting. If you approach the vehicle in front slowly, the arrows will
move from the grey area into the green area of the scale.
Applies to vehicles: with adaptive cruise control
•
The text messages and symbols in this section of the
display are not shown permanently.
Driver intervention prompt: If you approach the vehicle in front
quickly, the arrows act as a warning. When the actual distance is
shorter (or is likely to become shorter) than the distance selected,
the arrows move into the red area of the scale. In certain situations,
you may need to intervene as the driver ⇒ page 138, “Driver intervention prompt”.
System status indicator in the instrument
cluster display
C Status
A
•
ACC OFF (in white letters): The adaptive cruise control is
switched off.
•
Fig. 146 Instrument
cluster: Further information
ACC AVAILABLE (in white letters): The system is switched on but
the control has not yet been activated.
•
OVERRIDE (in white letters): You have exceeded the target speed
by accelerating.
Time intervals (e.g.
DISTANCE! (in red letters): The distance to the vehicle in front is
not sufficient and you have to brake the vehicle with the foot brake.
The various symbols for the time intervals -arrow- ⇒ fig. 146 appear
when you change the settings.
DISTANCE 1 to DISTANCE 4 (in green letters): Shows the time
interval you have selected. The adaptive cruise control is in cruise
mode.

•
•
•
DISTANCE 1 - dyn., DISTANCE 1 - comf. etc. (in green letters): If
the settings are adjusted on the sound system or MMI* such that
the “standard” driving program is replaced by “comfort” or
“dynamic”, the message above will indicate the setting.
)
The symbol  indicates that the warning tone has been switched
off.
...
The text message ... (three white dots) appears if a setting made
with the control lever cannot be implemented. There can be several
reasons for this:
•
You have pulled the control lever towards you to resume the
programmed cruising speed, without a target speed having been
set.
•
The control lever has been pushed up / down to increase / reduce
the speed, without a target speed having been set.
document_0900452a81b1b9de.book Seite 137 Donnerstag, 26. Juli 2007 9:16 09
adaptive cruise control (ACC)
•
The control lever has been pushed up / down to increase / reduce
the speed, but the resulting speed would be outside the range of 30
to 200 km/h.
ACC deactivation
The message ACC deactivation sometimes appears on vehicles with
a manual gearbox. If you press the clutch pedal for longer than
about 20 seconds, the adaptive cruise control will be automatically
deactivated and a warning tone will sound.
ACC not available
ESP activation
The text message ESP activation appears if the Electronic Stabilisation Programme (ESP) has intervened. In this case, the adaptive
cruise control will automatically be switched off. This is indicated by
a warning tone.
Speed (in km/h)
The target speed (in km/h) will appear in the display whenever it is
stored or changed ⇒ page 131, “Setting the speed” and
⇒ page 131, “Setting a new speed”.
The text message ACC not available will appear if, for example, the
brakes are overheated. The adaptive cruise control will then temporarily not be available. This is indicated by a warning tone.
Speed range
ACC not available!
To set a target speed, the speed of the vehicle must be at least
30 km/h. The cruise control system switches off if the speed falls
below 20 km/h.
The text message ACC not available! appears if a malfunction
should occur. The adaptive cruise control will then be switched off.
This is indicated by a warning tone. Have the system checked by a
qualified workshop.
ACC sensor blocked!
The text message ACC sensor blocked! appears if the ACC system
can no longer detect objects reliably. The adaptive cruise control
will then be switched off. This is indicated by a warning tone.
The ACC sensor is obstructed by dirt or foreign objects (e.g. leaves
or snow). Clean the sensor to restore the function ⇒ page 128,
fig. 136.
Engine speed !
On vehicles with manual gearbox, the text message Engine speed !
will appear if the driver does not change gear in time when the
adaptive cruise control accelerates or brakes the vehicle. The adaptive cruise control will automatically be deactivated if the engine
speed is not maintained within the permissible range. This is indicated by a warning tone.
Controls
Safety
Driving tips
137
The text message speed range appears if the current speed is too
low to set or to maintain the target speed.
If the speed exceeds 200 km/h (OVERRIDE), the system will remain
active and will reduce the speed to 200 km/h once the driver stops
accelerating.
ACC functionality limited
The text message ACC functionality limited appears if the ACC
system does not detect any objects for an extended period. The
distance to vehicles in front is not being controlled while the
message is displayed. The ACC system is not deactivated, and so
extra care should be taken! The text message ACC functionality
limited can appear for the following reasons:
•
The ACC sensor is dirty. The ACC system is not responding or is
not responding correctly to the vehicles in front!
•
You may be driving on a country road with no traffic and no clear
roadside demarcation (e.g. safety barriers, traffic signs, trees). As
soon as the system detects a vehicle, distance control is resumed
and the text message disappears.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 138 Donnerstag, 26. Juli 2007 9:16 09
138
adaptive cruise control (ACC)
The ACC sensor is located inside the trim grille (front right)
⇒ page 128, fig. 136. If the sensor is no longer functioning due to
dirt or obstruction in this area, it should be cleaned.
Parking brake !
Applies to vehicles: with adaptive cruise control
Driver intervention prompt
The driver intervention prompt is a warning for the driver
to reduce speed manually.
The text message Parking brake ! appears if the parking brake is
operated. The adaptive cruise control will then be switched off. This
is indicated by a warning tone.
Gear lever position !
On vehicles with manual gearbox the text message Gear lever
position ! appears when no valid forward gear is selected, i.e.
reverse gear or 1st gear is engaged or the gear lever is in the neutral
position. Adaptive cruise control is not available when the lever is in
these positions.
Shift lever position!
On vehicles with automatic gearbox the text message Shift lever
position ! appears if the shift lever is moved to position N. Adaptive
cruise control is not available when the lever is in this position.
Fig. 147 Instrument cluster: Driver intervention prompt
In some situations the adaptive cruise control system alone is not
able to brake the vehicle sufficiently to maintain a safe distance to
the vehicle in front. The adaptive cruise control system will then call
on you as the driver to take control of the situation yourself.
The Driver intervention prompt provides both a visual and an
acoustic warning.
•
A red vehicle symbol will appear in the instrument cluster
display ⇒ fig. 147.
•
•
The system status indicator will show DISTANCE!.
The red warning lamp will start to flash.
document_0900452a81b1b9de.book Seite 139 Donnerstag, 26. Juli 2007 9:16 09
adaptive cruise control (ACC)
•
An acoustic warning will also sound (unless it has been deactivated in the sound system or MMI* settings).
•
Note
Pressing the brake pedal will switch off the adaptive cruise
control system. The speed set at that point will, however, remain
stored until the adaptive cruise control is activated again.
139
Applies to vehicles: with adaptive cruise control
Setting the warning tone volume and driving
program
You can change the adaptive cruise control settings on
the sound system or MMI* to suit your individual driving
style.
•
To resume the programmed cruising speed, release the brake
pedal and pull the control lever towards you ⇒ page 132,
“Switching off the system (with speed memory function) and reactivating it”.
•
If you exceed the target speed by pressing the accelerator, the
driver intervention prompt will not be accompanied by a warning
tone. The indicator lamp shown in the display will also switch off
when the target speed is exceeded.
•
If the adaptive cruise control triggers a braking operation the
hydraulic brake system is under pressure. This is why brake pedal
travel will be shorter and the pedal will feel “harder”.
Fig. 148 Display: adaptive cruise control
– Select: Function selector button CAR > adaptive cruise
control.
Setting the volume of the warning tone
If the adaptive cruise control system switches off (e.g. when the ESP
intervenes) or a driver intervention prompt appears, a warning tone
will sound.
You can set the volume of the warning tone to low, medium, or high.
The new volume will sound briefly after making any adjustment. If
you do not want a tone to sound, select off.
Adjusting the basic settings
You can set the distance (time interval) you want the adaptive cruise
control system to keep to the vehicle in front by selecting distance
1, distance 2, distance 3 or distance 4.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 140 Donnerstag, 26. Juli 2007 9:16 09
140
adaptive cruise control (ACC)
Setting the driving program
In the Driving program menu you can select either dynamic,
standard or comfort according to your personal preferences.
•
Note
We recommend you to leave the warning tone switched on. Even
when the warning tone is switched off, not every warning tone will
be deactivated.
•
When you pass the key on to somebody else please remember to
make the other driver aware of the ACC settings.
•
We recommend a minimum distance setting of DISTANCE 3
(factory default setting).
•
When the ignition is switched off, the distance setting reverts to
the factory default DISTANCE 3. A qualified workshop can cancel
this function. In this case a default distance setting defined on the
sound system or MMI* is applied each time the engine is started.
•
•
•
When other vehicles change lanes ⇒ page 141.
When other vehicles are not clearly discernible ⇒ page 141
When vehicles are stationary ⇒ page 142.
WARNING
The radar sensor's "field of vision" can be impaired by rain, snow
or a lot of water on the road. This results in vehicles in front not
being properly recognised or, in some circumstances, not being
detected at all. If necessary, take action yourself!
Applies to vehicles: with adaptive cruise control
When driving through bends
System limitations
Applies to vehicles: with adaptive cruise control
General notes
The following situations could impair the function of the
radar sensor.
Fig. 149 Driving into a
bend
The adaptive cruise control is subject to given physical limits and
also has certain limits determined by the system itself. Under
certain circumstances the driver may feel that the ACC system is
responding unexpectedly or belatedly. For this reason, please
always give your full attention to road traffic and if necessary take
action yourself:
•
•
When driving through bends ⇒ page 140.
When vehicles in front are not in line with your vehicle
⇒ page 141.
Fig. 150 Driving out of
a bend
document_0900452a81b1b9de.book Seite 141 Donnerstag, 26. Juli 2007 9:16 09
adaptive cruise control (ACC)
Driving into a bend
Applies to vehicles: with adaptive cruise control
When you are driving into a bend, the ACC system may react to a
vehicle travelling in the other lane and therefore brake the vehicle
⇒ page 140, fig. 149. You can override the braking effect by pressing
the accelerator.
Other vehicles changing lanes
141
Driving out of a bend
When you are driving out of a long bend, the ACC system may - in
the course of its calculation of the lane ahead - react to a vehicle
travelling in the other lane and therefore brake the vehicle
⇒ page 140, fig. 150. You can override the braking effect by pressing
the accelerator.
Fig. 152 A vehicle is
changing lanes
Applies to vehicles: with adaptive cruise control
Vehicles which are very close to you when they move onto your lane
cannot be detected by the radar sensor until they move into its
range.
Vehicles in front travelling out of line
Applies to vehicles: with adaptive cruise control
Not clearly discernible vehicles
Fig. 151 The vehicle in
front is outside the
range of the radar
sensor
Vehicles in front which are not in line with your vehicle cannot be
detected by the ACC system until they are within the range of the
sensor.
Fig. 153 Motorcycle in
front
Vehicles that are not clearly discernible, e.g. a motorcycle travelling
in front of you and vehicles with a large amount of ground clearance
or protruding freight, are often identified late or may not be
detected at all.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 142 Donnerstag, 26. Juli 2007 9:16 09
142
adaptive cruise control (ACC)
Audi braking guard
Applies to vehicles: with adaptive cruise control
Stationary vehicles
Applies to vehicles: with adaptive cruise control
Description
Audi braking guard warns you in case of an impending
collision with a vehicle in front.
Fig. 154 Vehicle
turning off and vehicle
stationary
Fig. 156 Instrument
cluster: Display
Fig. 155 Vehicle
changing lane and
vehicle stationary
If a vehicle detected by the ACC system turns off or changes lane
and another stationary vehicle is located in front of that vehicle, the
ACC system will not react to the stationary vehicle ⇒ fig. 154 and
⇒ fig. 155.
Audi braking guard is active at speeds above approximately 30 km/h
and operates within the system limitations ⇒ page 140 even when
the adaptive cruise control is deactivated.
The radar sensor is fitted at the front of the vehicle ⇒ page 130,
fig. 137. The system requires reflecting surfaces in order to be able
to measure the distance. If the ACC is unable to measure the
distance it will not respond.
Once the system has measured the distance, it can assess a
dangerous situation where a vehicle in front brakes suddenly or you
are driving fast and approach a vehicle travelling at a much slower
speed. The system warns you as soon as it anticipates that a potential collision with the vehicle in front can only be avoided by hard
braking or by taking evasive action.
The system has a preset response time so that it can warn you in
time. In certain situations, the system response time will be reduced
dynamically, e.g. when you are accelerating onto a motorway.
Braking, lateral acceleration and steering angle are other factors
document_0900452a81b1b9de.book Seite 143 Donnerstag, 26. Juli 2007 9:16 09
adaptive cruise control (ACC)
which can shorten the system response time. The warning will be
deactivated if you press the accelerator pedal right down in order to
overtake.
WARNING (continued)
for determining your speed and for keeping a safe distance to the
other vehicles on the road.
The system draws the driver's attention to two different hazardous
situations:
•
Distance !
•
A distance warning will be given if you travel too close to the vehicle
in front for longer than 5 seconds. For example, if the distance is
less than 9 m at 80 km/h, a message will appear in the instrument
cluster display ⇒ page 142, fig. 156.
If the vehicle in front were to brake hard, a collision would no longer
be avoidable, even if you reacted immediately. In this case, you
should leave more room between your car and the vehicle in front.
Speed
If the vehicle in front of you is travelling in the same lane at a much
slower speed or if it brakes hard, the Audi braking guard will calculate the time at which a collision can be avoided only by emergency
braking or evasive action. When the system warns you, it is possible
to avoid a potential collision with the vehicle in front by braking or
changing lane. There are two warning levels:
•
Early warning: A message will appear in the instrument cluster
display and you will also hear a warning tone.
Always maintain the statutory minimum safety distance to the
vehicle in front (risk of accident).
Due to the system limitations, the Audi braking guard will not
react in certain situations, for example when approaching a
stationary obstacle (such as the end of a traffic jam or a brokendown vehicle).
•
Please note that the Audi braking guard is subject to limitations in tight bends on account of the radar sensor's field of vision.
This means that obstacles may not be detected in certain situations.
•
The radar sensor's "field of vision" can be impaired by rain,
snow or a lot of water on the road. This results in vehicles not
being reliably recognised or, in some circumstances, not being
detected at all. Always keep the road ahead within your field of
vision.
•
Reflecting objects, such as crash barriers or the entrance to a
tunnel, could impair the function of the radar sensor.
Applies to vehicles: with adaptive cruise control
•
Status messages in the instrument cluster
display
If you brake hard, the brake assist system ⇒ page 222 helps you to
achieve the optimum braking effect.
braking guard brake jolt
Acute warning: The second (acute) warning will be triggered if
you do not react to the advance warning. There will automatically be
a short dab of the brakes to remind you to concentrate on the traffic.
This driver message appears when the brakes are dabbed due to an
acute warning.
braking guard off
WARNING
Please always direct your full attention to the road, even when the
Audi braking guard is activated. It is always you who is responsible
Controls
143
Safety
Driving tips
This driver message appears when the system is switched off in the
MMI. The message also appears briefly after you begin driving if the
system is switched off.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 144 Donnerstag, 26. Juli 2007 9:16 09
144
adaptive cruise control (ACC)
The message will also appear if the system is unavailable due to an
error or if you switch the ESP off ⇒ page 222. In this state, the
system no longer warns you about an impending collision.
Applies to vehicles: with adaptive cruise control
Settings for Audi braking guard
The system and warning settings can be adjusted via the
sound system or MMI*.
Fig. 157 Display: Audi
braking guard
– Select: Function selector button CAR > Audi braking
guard.
•
System - The Audi braking guard system can be switched on and
off.
•
Early warning - The acoustic signals and display messages can
be switched on and off.
Note
The settings are stored on the remote control key in use. When you
pass the key on to somebody else please remember to make the
other driver aware of the Audi braking guard settings ⇒ page 43.
document_0900452a81b1b9de.book Seite 145 Donnerstag, 26. Juli 2007 9:16 09
Audi lane assist
145
Audi lane assist
Audi lane assist
WARNING (continued)
adverse light. This can result in the system not detecting the lane
markings correctly.
Applies to vehicles: with lane assist
Description
The lane assist system assists the driver in keeping the
vehicle in the right lane.
Applies to vehicles: with lane assist
Switching on and off
The system uses a camera to detect the markings of the lane you are
driving in. If the vehicle approaches one of the detected lane markings, the steering wheel vibrates to warn the driver that the vehicle
might be about to cross one of the markings. The lane assist system
is functional when it has detected lane markings on both sides of
the lane you are driving in. The green lamp  in the instrument
cluster indicates that the function is activated and fully functional.
If you operate the turn signal before crossing one of the lane markings (while the lane assist system is functional), the system will
detect that the lane change is intended and will not warn the driver.
Fig. 158 Turn signal
lever: Pushbutton for
Audi lane assist
As the system is designed for driving on motorways and other major
roads, it is only active above a speed of about 65 km/h.
WARNING
•
The lane assist system does not keep the vehicle in its lane. It
merely warns the driver when the vehicle is in danger of crossing
the markings of the lane. As the driver you are always responsible
for staying in your own lane.
Fig. 159 Windscreen:
Camera window for
Audi lane assist
•
The camera cannot detect all lane markings. Therefore it is
possible that variations in the road surface or objects might be
detected as lane markings, which can lead to false warnings, or
warnings not being given.
•
The camera's view might be obstructed, for example by vehicles travelling in front, rain, snow, a lot of water on the road or
Controls
Safety
Driving tips
– Press the button ⇒ fig. 158 -arrow- to switch the system
on and off. The indicator lamp  in the instrument
cluster will light up or go out.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 146 Donnerstag, 26. Juli 2007 9:16 09
146
Audi lane assist
Indicator lamp in instrument cluster
Applies to vehicles: with lane assist and on-board computer
 Active: The green indicator lamp confirms that the system is fully
Instrument cluster display
functional. You will be warned if you are about to cross the lane
markings detected by the system.
 Inactive: The yellow warning lamp indicates that the system is
switched on. However, you will not be warned if you cross the lane
markings. This can have the following causes:
•
•
There is only one or no lane marking.
The system cannot detect the lane markings (e.g. due to snow,
dirt, wet conditions or adverse light).
Fig. 160 Instrument
cluster: lane assist
switched on and in
warning mode
•
There are more than two lane markings in the lane you are
driving in (e.g. in roadwork sections).
•
The vehicle's speed is below 65 km/h, the speed at which the lane
assist system is activated.
•
•
•
The lane is narrower than 2.5 m or wider than 5 m.
The bend is too tight.
Note
Make sure that the camera window ⇒ page 145, fig. 159 is not
covered with stickers or similar objects.
Fig. 161 Instrument
cluster: lane assist
switched on but not
ready for warning
•
Always keep the camera window clean. Usually it should suffice
to operate the windscreen wipers.
You can call up the display for the lane assist by repeatedly pressing
the RESET button on the windscreen wiper lever. For more details
refer to ⇒ page 27.
When the lane assist is switched on, two lines indicate the lane
demarcations on the left and right of your vehicle.
Version
•
•
A : Monochrome display
A
Solid red lines: The lane assist is switched on and ready to warn.
One red line flashing (left or right): The lane assist warns you
before you cross the lane demarcation ⇒ fig. 160, A
document_0900452a81b1b9de.book Seite 147 Donnerstag, 26. Juli 2007 9:16 09
Audi lane assist
•
Unfilled lines: The lane assist is switched on but not ready for
A
warning ⇒ page 146, fig. 161, A
Version
•
147
The system should be checked by an Audi dealership or other qualified workshop.
B : High-resolution display
A
Solid white lines: The lane assist is switched on and ready to
warn.
Applies to vehicles: with lane assist
•
Setting the warning time and steering
vibration
•
You can change the lane assist settings on the sound
system or MMI* to suit your individual preferences.
Solid red line (left or right): The lane assist warns you before you
cross the lane demarcation ⇒ page 146, fig. 160.
Unfilled lines: The lane assist is switched on but not ready for
warning ⇒ page 146, fig. 161.
Messages in the instrument cluster display
Should the lane assist be deactivated automatically, the indicator
lamp in the instrument cluster will go out and one of the following
messages will appear in the instrument cluster display:
Audi lane assist not available: currently no sensor vision
This message is displayed when the camera is no longer functional
after the system has continuously failed to detect the lane markings. This can have the following causes:
Fig. 162 Display:
Setting time of
warning and steering
vibration
•
The outside of the camera window ⇒ page 145, fig. 159 is dirty
or frosted. Please remove dirt or ice from this area of the windscreen.
•
The inside of the camera window is misted up. In this case,
please wait for the camera window to demist before switching on
the lane assist system again.
•
Due to the conditions (e.g. snow-covered road) the system has
not been able to detect the lane markings for a long period. Do not
switch the lane assist system on again before the lane markings are
discernible.
Audi lane assist currently not available
A temporary error is preventing the lane assist system from fully
functioning. Try switching on the lane assist system again later.
Audi lane assist: system fault
Controls
Safety
Driving tips
– Select: Function selector button CAR > Audi lane assist.
Setting time of warning
early: In this setting, the driver will be warned before a wheel
crosses a lane marking. The warning depends on the angle with
which the vehicle is approaching the lane marking. The larger the
angle with which you are driving towards the marking, the earlier
you will receive the warning, i.e. the distance between the vehicle
and the marking might still be still relatively long. If you are driving
toward the marking at a very narrow angle, you will receive the
warning later, i.e. shortly before one of the wheels touches the
marking.
adaptive: In this setting, the time of warning is adapted to the road
layout and the vehicle's speed. The warning will be received later
when you are driving through a bend, and earlier when you are
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 148 Donnerstag, 26. Juli 2007 9:16 09
148
Audi lane assist
driving on a straight section. On narrow roads, the system will give
off warnings later than on wide roads.
late: In this setting, the driver will be warned when a wheel crosses
a lane marking.
Setting steering wheel vibration
You can set the steering vibration to low, medium or strong. The
steering wheel will vibrate so that you can check your selection.
•
Note
The lane assist is not active while you are changing the setting;
the brief vibration of the steering wheel is only intended to help you
make the desired setting.
•
Your personal settings are stored automatically and assigned to
the remote control key which is being used.
document_0900452a81b1b9de.book Seite 149 Donnerstag, 26. Juli 2007 9:16 09
Audi side assist
149
Audi side assist
Lane change assist feature
Warning lamps are incorporated in the two exterior mirrors
⇒ fig. 164. The warning lamp on the left-hand mirror assists the
driver when changing lane towards the left and the warning lamp
on the right-hand mirror assists the driver when changing lane
towards the right.
Applies to vehicles: with side assist
Description
The side assist function assists the driver when changing
lanes.
Fig. 163 Rear bumper:
Position of radar
sensors (not externally
visible)
When one of these lamps lights up, this is to inform you that the
side assist has detected a vehicle on that side and calculates that a
lane change would be critical. This is the first stage of the warning,
referred to as the information mode ⇒ page 151. This stage of the
warning is designed to be visible only when you look in the exterior
mirror.
If you operate the turn signal when the side assist has registered
what it judges to be a critical vehicle, the lamp on the exterior mirror
will then flash several times with greater intensity. This is the
warning mode ⇒ page 151.
Applies to vehicles: with side assist
Switching on and off
Fig. 164 Warning lamp
on exterior mirror
(driver's side)
Fig. 165 Driver's door:
Button for side assist
The side assist function employs radar sensors ⇒ fig. 163 to assist
the driver in monitoring following traffic and the blind spots on both
sides of the car ⇒ page 151, fig. 166.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 150 Donnerstag, 26. Juli 2007 9:16 09
150
Audi side assist
Switching on
– Press the button ⇒ page 149, fig. 165. The red indicator
lamp in the button will light up.
•
Switching off
•
– Press the button again. The indicator lamp in the button
will go out.
The system is designed to provide assistance on motorways and
other out-of-town roads, so it only operates at speeds above about
60 km/h.
WARNING
•
Please note that the sensors are not always able to detect all
vehicles which may represent a potential hazard (accident risk).
•
Please note that the side assist is not able to give adequate
warning of vehicles approaching very fast from behind, or vehicles
that you are overtaking rapidly.
•
The radar sensor's "field of vision" can be impaired by rain,
snow or a lot of water on the road. This results in vehicles not
being reliably recognised or, in some circumstances, not being
detected at all by the side assist. Always give your full attention to
the position of your vehicle on the road and other nearby traffic.
•
The side assist only gives a warning of approaching vehicles
and vehicles in the blind spots when road speed is above 60 km/h.
•
Please note that the side assist does not operate in tight bends
(with a radius of less than 200 metres).
•
The side assist feature is not a substitute for the full concentration of the driver. The driver is always responsible for the safety of
lane changes and other manoeuvres. Always give your full attention to the position of your vehicle on the road and other nearby
traffic.
Caution
To avoid impairing the function of the side assist, do not attach
any objects (e.g. stickers or bicycle carriers) in such a way that they
might interfere with the radar sensors in the rear bumper.
Make sure that the warning lamps on the exterior mirrors are not
obscured by stickers or other objects.
•
Note
To ensure that the side assist function works properly, do not
allow snow and ice to accumulate on the rear bumper near the radar
sensors. Please observe the additional notes on ⇒ page 157.
•
The side assist function will be switched off automatically when
the electrical connector for the trailer socket is plugged in on vehicles with a factory-fitted towing bracket.
•
The side assist should be switched off manually when towing a
trailer if the vehicle is equipped with a towing bracket which was not
factory-fitted.
•
The side assist system will switch off automatically if it detects
an obstruction that impairs the function of the radar sensors.
•
The warning lamps on the exterior mirrors may not be properly
visible if tinted foil is affixed to the side windows on the driver's or
passenger's side.
document_0900452a81b1b9de.book Seite 151 Donnerstag, 26. Juli 2007 9:16 09
Audi side assist
151
on the relevant exterior mirror will light up whenever the side assist
calculates that the distance and the speed differential of
approaching vehicles would be critical in the event of a lane change.
Applies to vehicles: with side assist
Area covered by the radar sensors
The warning lamp may light up when you are being overtaken and
when you are overtaking another vehicle.
If you are overtaking slowly, with a speed differential of less than
15 km/h, the warning lamp will light up as soon as the other vehicle
enters your blind spot and is detected by the sensors. If you are
overtaking with a speed differential which is greater than this the
lamp will not give a warning.
Fig. 166 Schematic
diagram: Area covered
by the radar sensors
The area covered by the radar sensors ⇒ fig. 166 consists of:
•
The rearward approach zone (light green area: up to about 50
1 and
metres) A
•
Blind spots (dark green area)
2 .
A
The radar sensors monitor the lanes immediately to the left and
right of your vehicle. Other lanes are not covered by the sensors.
Note
Information mode and warning mode
The side assist has two modes of operation
•
•
The information mode and
The warning mode
The side assist will respond in the appropriate mode, depending on
whether or not you operate the turn signal to indicate an intended
lane change.
Information mode
The side assist system is programmed for lanes of a fixed width, and
is not able to measure differing lane widths. It monitors a zone
equivalent to one normal lane width on either side. If the lanes are
narrower than this, or if vehicles are not travelling in the centre of
the lanes, the system may register vehicles that are not in fact travelling in an adjacent lane ⇒ page 156.
Applies to vehicles: with side assist
How the system works
When other vehicles are detected, the side assist system registers
their distance and how fast they are approaching. The warning lamp
Controls
Applies to vehicles: with side assist
Safety
Driving tips
As long as you do not operate the turn signal, the side assist will
merely inform you of the presence of vehicles that it has detected
and judges to be critical in the event of a lane change. The warning
lamp on the relevant exterior mirror will light up with low intensity
whenever the side assist calculates that the distance and the speed
differential of an approaching vehicle are critical.
The intensity of the warning lamp in this information mode is deliberately kept relatively low, so that it does not distract you while you
are looking at the road in front and do not intend to change to a
different lane. The information mode is clearly visible when you look
in the exterior mirror.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 152 Donnerstag, 26. Juli 2007 9:16 09
152
Audi side assist
Warning mode
1 Warning lamp on exterior mirror does not light up
A
If you operate the turn signal when the side assist has detected a
vehicle on that side that it judges to be critical in the event of a lane
change, the warning lamp on the relevant exterior mirror will flash
brightly several times. This is the warning mode: if the lamp flashes
brightly it warns you that you should check the situation again in the
mirror and by looking back over your shoulder ⇒
in “Safety
notes” on page 157.
The sensors have not detected any vehicles. The warning lamp on
the exterior mirror does not light up ⇒
in “Safety notes” on
page 157.
Note
2 Warning lamp lights up in information mode
A
The sensors have detected a rapidly approaching vehicle - in this
example in the left-hand lane. Because of its approach speed, this
vehicle is already judged to be critical in the event of a lane change
even though it is still some distance away. The warning lamp on the
exterior mirror lights up in the information mode ⇒ page 151.
You can adjust the brightness of the warning lamps on the exterior
mirrors via the MMI ⇒ page 155.
3 Warning lamp flashes in warning mode
A
Applies to vehicles: with side assist
2 , the warning lamp on
If you operate the turn signal in situation A
the exterior mirror will flash briefly several times. This calls your
attention to the presence of a vehicle which you may have overlooked.
Situation with vehicle approaching rapidly
from behind
•
Note
The faster a vehicle approaches, the earlier the warning will
appear on the exterior mirror. In all cases, the side assist will give a
warning for the vehicles it has detected at the latest when they enter
the “blind spot”.
•
If a vehicle is approaching at high speed it is possible that a lane
change may be critical, even though no warning is given.
Fig. 167 side assist: Vehicles approaching rapidly from behind
document_0900452a81b1b9de.book Seite 153 Donnerstag, 26. Juli 2007 9:16 09
Audi side assist
Applies to vehicles: with side assist
Situation with vehicle approaching slowly
from behind
153
In all cases, the side assist will light up to indicate the vehicles it has
detected at the latest when they enter the “blind spot”.
3 Warning lamp flashes in warning mode
A
2 , the warning lamp on
If you operate the turn signal in situation A
the exterior mirror will flash briefly several times. This calls your
attention to the presence of a vehicle which you may have overlooked.
•
Note
The faster a vehicle approaches, the earlier the warning will
appear on the exterior mirror. The side assist will give a warning for
the approaching vehicles it has detected at the latest when they
enter the “blind spot”.
•
If a vehicle is approaching at high speed it is possible that a lane
change may be critical, even though no warning is given.
Fig. 168 side assist: Vehicles approaching slowly from behind and vehicles in
the blind spot
1 Warning lamp on exterior mirror does not light up
A
The sensors have detected a slowly approaching vehicle - in this
example in the left-hand lane. Because it is relatively far away and
only approaching slowly, no warning will appear on the exterior
mirror ⇒
in “Safety notes” on page 157.
2 Warning lamp lights up in information mode
A
The slowly approaching vehicle is now closer. The warning lamp on
the exterior mirror lights up in the information mode.
The warning lamp on the exterior mirror will only light up if the side
assist calculates that the distance and the speed differential of
approaching vehicles would be critical in the event of a lane change.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 154 Donnerstag, 26. Juli 2007 9:16 09
154
Audi side assist
Applies to vehicles: with side assist
Situation when you are slowly overtaking
other vehicles
attention to the presence of a vehicle which you may have
overlooked.
Applies to vehicles: with side assist
Situation when you are rapidly overtaking
other vehicles
Fig. 169 side assist: Other vehicles being overtaken slowly
1 Warning lamp on exterior mirror does not light up
A
The vehicle you are overtaking has not yet been detected by the side
assist. The warning lamp on the exterior mirror does not light up
⇒
in “Safety notes” on page 157.
2 Warning lamp lights up in information mode
A
The vehicle you are passing slowly (with a speed differential less
than 15 km/h) is detected by the side assist. The warning lamp on
the exterior mirror lights up in the information mode.
3 Warning lamp flashes in warning mode
A
2 , the warning lamp on
If you operate the turn signal in situation A
the exterior mirror will flash briefly several times. This calls your
Fig. 170 side assist: Other vehicles being overtaken rapidly
1 Warning lamp on exterior mirror does not light up
A
The vehicle you are overtaking has not yet been detected by the side
assist. The warning lamp on the exterior mirror does not light up
⇒
in “Safety notes” on page 157.
2 Warning lamp on exterior mirror does not light up
A
The vehicle you are passing rapidly (with a speed differential greater
than 15 km/h) is detected by the side assist but is not judged to be
critical in the event of a lane change since it is dropping back
document_0900452a81b1b9de.book Seite 155 Donnerstag, 26. Juli 2007 9:16 09
Audi side assist
quickly. The warning lamp on the exterior mirror does not light up
⇒
in “Safety notes” on page 157.
tion mode. The intensity of the lamp in the warning mode is linked
to the intensity in the information mode.
3 Warning lamp on exterior mirror does not light up
A
The brightness of the lamp in the information mode should be set
so that you can see the lamp when you glance at the exterior mirror,
but are not aware of it when looking forwards through the windscreen.
2 , the warning lamp on
If you operate the turn signal in situation A
the exterior mirror will still not give any warning ⇒
in “Safety
notes” on page 157.
Applies to vehicles: with side assist
Adjusting brightness of warning lamp on
exterior mirror
You can adjust the brightness of the warning lamp on the
sound system or MMI*.
155
If you are in very dark or very light surroundings when you adjust the
brightness of the warning lamp, the automatic brightness control
may already have reached the lowest or the brightest setting. Under
these circumstances the brightness of the warning lamp on the
exterior mirror may not change visibly when you alter the basic
brightness level.
If you adjust the basic brightness level while the vehicle is in in very
dark or very light surroundings, the change in the setting may only
become visible in surroundings of more moderate brightness.
•
Note
The side assist is not active while you are changing the brightness setting; the brief flash of the warning lamp is only intended to
help you make the desired setting.
Fig. 171 Display:
Adjusting brightness
of warning lamp
– Select: Function selector button CAR > Audi side assist
> Warning lamp: brightness.
The brightness of the warning lamp in both the information and
warning modes is regulated automatically according to the ambient
light level. You can also adjust the basic brightness level of the
warning lamp yourself via the function Warning lamp: brightness.
•
Your personal settings are stored automatically and assigned to
the remote control key which is being used.
Applies to vehicles: with side assist
General notes
The side assist system has inherent limitations in some situations.
For this reason, please take particular care:
•
•
When driving through bends ⇒ page 156
On roads with varying lane widths ⇒ page 156.
The new brightness level will be displayed briefly while you are
making the adjustment. The brightness level that is shown at this
point is the intensity of the lamp when it comes on in the informa-
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 156 Donnerstag, 26. Juli 2007 9:16 09
156
Audi side assist
whether you are driving directly in the centre of your lane or further
to one side.
Applies to vehicles: with side assist
When driving through bends
The side assist cannot detect vehicles in tight bends (with a radius
of less than 200 metres).
When driving through a bend, the side assist may react to a vehicle
that is two lanes away and activate the warning lamp in the exterior
mirror.
Applies to vehicles: with side assist
If the lane widths are reduced, the sensors may also detect vehicles
in additional lanes, especially if you are driving further to one side
of your lane ⇒ fig. 173. In such situations the system may react to
vehicles travelling two lanes away, so that the side assist activates
the information or the warning mode.
Similarly, if the lanes are very wide, it is possible that the system
may not detect vehicles in the adjacent lane because they are
outside the area covered by the sensors.
Lane widths
Notes
Applies to vehicles: with side assist
Messages in the instrument cluster display
Should the side assist be deactivated automatically, the indicator
lamp in the button will go out and a message will appear in the
instrument cluster display:
Fig. 172 Lanes of
normal width are
covered by the sensors
Audi side assist not available: sensors blocked
The sensors, which are not externally visible, are incorporated on
either side of the rear bumper ⇒ page 149, fig. 163. To ensure the
proper function of the side assist system, do not attach any objects
(such as stickers or bicycle carriers, etc.) to the rear bumper in such
a way that they might obstruct these sensors. Should the function
of the system be impaired, the instrument cluster display will show
this message. Please check whether anything is obstructing the
sensors and remove the obstruction if necessary.
Fig. 173 Narrow lanes:
side assist may react
to vehicles travelling
two lanes away
The side assist system is designed to cover adjacent lanes of normal
width on both sides of your vehicle (left and right), regardless of
Audi side assist currently not available
The side assist is temporarily inoperative and cannot be switched
on (for instance if the battery is not sufficiently charged).
document_0900452a81b1b9de.book Seite 157 Donnerstag, 26. Juli 2007 9:16 09
Audi side assist
Audi side assist: system fault
157
WARNING (continued)
The system should be checked by an Audi dealership or other qualified workshop.
Audi side assist not available when towing
On vehicles with a factory-fitted towing bracket the side assist function will be switched off automatically when the electrical connector
for the trailer is plugged in, and this message will appear in the
instrument cluster display. The side assist function may not be
switched off automatically if the towing bracket is not of the factoryfitted type.
•
The radar sensor's "field of vision" can be impaired by rain,
snow or a lot of water on the road. This results in vehicles not
being reliably recognised or, in some circumstances, not being
detected at all by the side assist. Always give your full attention to
the position of your vehicle on the road and other nearby traffic.
•
The side assist only gives a warning of approaching vehicles
and vehicles in the blind spots when road speed is above 60 km/h.
•
Please note that the side assist does not operate in tight bends
(with a radius of less than 200 metres).
•
Applies to vehicles: with side assist
Safety notes
The function of the side assist can be restricted when driving in
tight bends or over crests and in bad weather conditions.
It is possible that the radar sensors may register objects such as
high or offset roadside barriers as well as other vehicles.
The side assist system is programmed for lanes of a fixed width, and
is not able to measure differing lane widths. It monitors a zone
equivalent to one normal lane width on either side. If the lanes are
narrower than this, or if vehicles are not travelling in the centre of
the lanes, the system may give a warning for vehicles which it
judges to be critical, even though they are not in fact travelling in an
adjacent lane.
The side assist feature is not a substitute for the full concentration of the driver. The driver is always responsible for the safety of
lane changes and other manoeuvres. Always give your full attention to the position of your vehicle on the road and other nearby
traffic.
Caution
To avoid impairing the function of the side assist, do not attach any
objects (e.g. stickers or bicycle carriers) in such a way that they
might interfere with the radar sensors in the rear bumper.
Note
For reasons of safety, the side assist system must be checked by a
qualified workshop if the positions of the radar sensors have been
affected by a rear-end collision, etc.
WARNING
Applies to vehicles: with side assist
•
Please note that the sensors are not always able to detect all
vehicles which may represent a potential hazard (accident risk).
Conformity certification
Please note that the side assist is not able to give adequate
warning of vehicles approaching very fast from behind, or vehicles
that you are overtaking rapidly.
The side assist employs radar sensors operating in one of two
frequency bands at 24 GHz. Please note that in some countries only
one of these two frequency bands is permitted. Accordingly, the
frequency band permitted in the country where the vehicle is being
•
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 158 Donnerstag, 26. Juli 2007 9:16 09
158
Audi side assist
operated must be set by a qualified workshop, or if necessary the
side assist must be deactivated.
The manufacturer certifies that, when used in the authorised
manner, the side assist conforms with the requirements of §3 and
the other relevant provisions of the “1999/5/EC Guideline issued by
the European Parliament and the European Council”.
The side assist is certified for use in the following countries:
Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia,
Finland, GB/Northern Ireland, Germany, Greece, Hungary, Iceland,
Ireland, Italy, (San Marino, Vatican City), Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain (Andorra, Balearic Islands, Canary Islands), Sweden,
Switzerland.
document_0900452a81b1b9de.book Seite 159 Donnerstag, 26. Juli 2007 9:16 09
Audi drive select
159
Audi drive select
Adjusting the vehicle set-up
Applies to vehicles: with Audi drive select
Introduction
Audi drive select allows you to use different set-ups on your vehicle.
Using the three modes COMFORT, AUTO and DYNAMIC, you can
change the set-up at the press of a button for a more comfortoriented or dynamic drive.
On vehicles with MMI*, you also have the INDIVIDUAL* mode, which
allows you to adapt the vehicle set-up individually to your personal
driving style. For example, you might choose to combine a more
dynamic engine set-up with a lighter steering response.
to be reduced at higher speeds in order to improve the handling of
the vehicle. The steering is more direct at lower speeds to minimise
the amount of steering effort required by the driver, e.g. when
manoevring in tight spaces. The dynamic steering* also provides a
more agile steering response at low and medium speeds. You can
adjust the basic characteristics of the steering in the Audi drive
select menu.
The suspension control* uses sensors to collect information on
steering movements, braking and acceleration input by the driver,
road surface quality, road speed and vehicle loading. Using this
information, the suspension can be adapted almost instantaneously to changing driving conditions. With Audi drive select, the
driver can choose between dynamic and comfort-oriented suspension set-ups (DYNAMIC and COMFORT modes), or opt for a more
balanced set-up (AUTO mode).
The following table provides an overview of the characteristics in
each driving mode.
Applies to vehicles: with Audi drive select
Description
The possible vehicle set-up in each mode depends on which equipment is installed on your vehicle. The engine and the servotronic
power steering are basic parts of your vehicle which are always
included in the set-up. In addition, you can change the characteristics of the automatic gearbox*, dynamic steering* and suspension
control*.
Systems
COMFORT
AUTO
DYNAMIC
Balanced
Balanced
Dynamic
Steering
Comfortable
Balanced
Dynamic
Engine or
engine/gearbox*
Dynamic steering*
The response of the engine and automatic gearbox* to accelerator
pedal movements will be more spontaneous or balanced,
depending on which mode you select.
Comfortable
(indirect)
Balanced
(direct)
Dynamic
(direct)
Suspension control*
Comfortable
Balanced
Dynamic
The servotronic power steering ⇒ page 225 will also respond to
different drive set-ups.
If your vehicle is equipped with dynamic steering*, the servotronic
power steering settings are adjusted in the Dynamic steering*
menu.
The dynamic steering* alters the steering ratio depending on the
road speed to optimise the amount of steering effort required by the
driver at any given time. This enables the sensitivity of the steering
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 160 Donnerstag, 26. Juli 2007 9:16 09
160
Audi drive select
•
Note
You can select the sport program for gear changes on vehicles
with an automatic gearbox* by activating the DYNAMIC mode. There
is no S position on the selector lever.
•
You may hear a noise on vehicles with dynamic steering* when
you start or stop the engine. This is no cause for concern.
Applies to vehicles: with Audi drive select
Selecting the driving mode
You can choose between COMFORT, AUTO, DYNAMIC and
INDIVIDUAL*.
The control is next to the selector gate ⇒ fig. 174 on vehicles with sound system, or in the centre console ⇒ fig. 175
on vehicles with MMI*.
– Switch on the ignition.
– Press the left or right arrow button until the desired
mode lights up in red.
You can change the driving mode while the vehicle is stationary or
moving. If traffic conditions permit, take your foot off the accelerator briefly after you change the mode so that the new mode is also
activated for the engine.
COMFORT
The COMFORT mode alters the vehicle set-up for a more comfortable ride. The response of the engine and automatic gearbox* to
accelerator pedal movements is balanced. The steering is light and
indirect* and the suspension control* is set to soft. This setting is
suitable for driving long distances on motorways for example.
AUTO
Fig. 174 Selector gate:
Control for Audi drive
select
The overall impression in AUTO mode is of a comfortable but
dynamic ride. This setting is suitable for everyday use.
DYNAMIC
DYNAMIC gives the vehicle a tighter set-up. The engine reacts spontaneously to accelerator pedal movements and the steering is
dynamic and direct*. The suspension control* is stiffer and the
automatic gearbox* changes gear at higher engine speeds. This
setting is ideal for performance driving.
INDIVIDUAL*
Fig. 175 Centre
console: Control for
Audi drive select
You can configure this mode on the MMI according to your personal
preferences.
document_0900452a81b1b9de.book Seite 161 Donnerstag, 26. Juli 2007 9:16 09
Audi drive select
WARNING
161
Note
Always keep an eye on the traffic when using the Audi drive select
controls - Risk of accident!
Your settings in INDIVIDUAL* mode are stored automatically and
assigned to the remote control key currently in use.
Note
If you remove the ignition key, the AUTO mode will be selected automatically the next time you switch on the ignition.
Applies to vehicles: with MMI and Audi drive select
Settings for INDIVIDUAL driving mode
You can configure your own personal vehicle set-up on
the MMI*.
Fig. 176 MMI display:
Changing the set-up
individually
– Select: Function selector button CAR > Audi drive select
individual.
To drive with the new vehicle set-up, remember to press the INDIVIDUAL* button ⇒ page 160.
The system settings available on the MMI* depend on which equipment is installed on your vehicle.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 162 Donnerstag, 26. Juli 2007 9:16 09
162
Automatic gearbox
Automatic gearbox
multitronic®, tiptronic (6-speed
gearbox)
Applies to vehicles: with multitronic® or tiptronic
General notes on using multitronic®
The gears are changed automatically.
Applies to vehicles: with multitronic® or tiptronic
Introduction
Applies to vehicles with multitronic® gearbox
The vehicle is equipped with an electronically controlled continuously variable transmission (multitronic®). Unlike conventional
automatics, the gear ratios are not shifted in fixed steps but continuously variable. This gives smoother transmission and makes for
better fuel economy.
The gearbox selects the gear ratio and shifts up or down automatically according to the gear change programmes stored in the
control unit ⇒ page 166.
If desired, you can also select the gears manually (tiptronic mode)
⇒ page 166.
Please note that on vehicles with a multitronic® gearbox, torque is
transmitted via a multi-plate clutch, and not via a torque converter
as on conventional automatics. This means that the car will not
“creep” as much as conventional automatics when the engine is
idling if you stop temporarily with the selector lever in position D, S
or R.
Fig. 177 Detail of the
centre console:
Selector lever with
interlock button
Driving away from a standstill
– Press and hold the brake pedal.
– Press and hold the interlock button (the button in the
selector lever handle), move the selector lever to the
desired position, for instance D, and release the interlock
button.
– Wait for the gearbox to engage the gear (a slight movement can be felt).
Applies to vehicles with tiptronic gearbox
– Release the brake and press the accelerator ⇒
The vehicle is equipped with an electronically controlled 6-speed
automatic gearbox. The gearbox changes up and down automatically.
Stopping briefly
If desired, you can also select the gears manually (tiptronic mode)
⇒ page 166.
.
– Apply the foot brake to hold the vehicle when stationary
(for instance at traffic lights).
document_0900452a81b1b9de.book Seite 163 Donnerstag, 26. Juli 2007 9:16 09
Automatic gearbox
– To prevent the vehicle from rolling away, apply the
parking brake before moving off on steep gradients
⇒
.
– As soon as you accelerate as normal, the parking brake
will automatically be released and the vehicle will start
moving.
Parking the car
– Press and hold the brake pedal ⇒
.
– Apply the parking brake.
– Press and hold the interlock button, move the selector
lever to P and release the interlock button.
The engine can only be started when the selector lever is at P or N.
163
WARNING (continued)
this reason, to avoid risking an accident, apply the footbrake firmly
when stopping to prevent the vehicle rolling away.
•
Never move the selector lever to R or P when driving, as this
could cause an accident.
•
Vehicles with multitronic® gearbox: Please note that some
power will still be transmitted when you stop temporarily with the
selector lever in position D, S or R. For this reason, to avoid risking
an accident, apply the footbrake firmly when stopping to prevent
the vehicle rolling away.
Applies to vehicles: with multitronic® or tiptronic
Selector lever positions
This section covers all the selector lever positions.
On level ground it is sufficient to move the selector lever to P. On a
gradient the parking brake should be applied first and the selector
lever should be moved to P. This reduces the load on the locking
mechanism and makes it easier to move the selector lever out of
position P.
Vehicles with multitronic® gearbox: Your vehicle is equipped with
the hill hold assist function which makes it easier to drive away on
a slope. The system is activated when you press and hold the brake
pedal for a few seconds. When you release the brake pedal the
braking force will be maintained for a moment in order to prevent
the vehicle rolling back when you drive away.
Fig. 178 Display:
Selector lever positions
The current selector lever position is shown in the instrument
cluster display.
WARNING
•
Do not press the accelerator while selecting a gear with the
vehicle stationary and the engine running, as this could cause an
accident.
P - Parking lock
Please note that some power will still be transmitted when you
stop temporarily with the selector lever in position D, S or R. For
The interlock button (the button in the selector lever handle) must
be pressed in and the brake pedal must be depressed before
•
Controls
Safety
Driving tips
This locks the driving wheels mechanically. The parking lock must
only be engaged when the vehicle is stationary ⇒
.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 164 Donnerstag, 26. Juli 2007 9:16 09
164
Automatic gearbox
moving the selector lever either in or out of position P. The lever can
only be moved out of position P when the ignition is on.
WARNING
R - Reverse gear
•
When reverse gear is engaged the gearbox automatically selects the
lowest gear ratio.
•
Reverse gear must only be engaged when the vehicle is stationary
and the engine is idling ⇒
.
To move the selector lever to position R, press in the interlock
button and at the same time press the brake pedal. Depending on
the model, one or two reversing lights will come on in selector lever
position R (when ignition is switched on).
N - Neutral
In this position the gearbox is in neutral ⇒
.
D - Drive (forwards)
In this position the gearbox automatically selects the best gear
ratio. This depends on the engine load, the road speed and the
dynamic gear control program (DCP).
Press the brake pedal when moving the selector lever from N to D if
the vehicle is stationary or at speeds below 5 km/h ⇒
.
In some situations (such as on mountain roads or when towing a
trailer or caravan) it can be advantageous to switch temporarily to
tiptronic mode ⇒ page 166, so that the gear ratios can be selected
manually to suit the driving conditions.
S - Sport position
Select this position if you wish to take full advantage of the car's
performance. This setting makes use of the engine's maximum
power output. When accelerating the gear shifts will be noticeable.
Press the brake pedal when moving the selector lever from N to S if
the vehicle is stationary or at speeds below 5 km/h ⇒
.
Never move the selector lever to R or P when driving, as this
could cause an accident.
In selector position D or S the vehicle must always be held with
the foot brake when the engine is running. This is because an automatic gearbox still transmits power even at idling speed, and the
vehicle tends to “creep”. The throttle must on no account be
opened inadvertently (for instance by hand from the engine
compartment) when a gear is engaged with the vehicle stationary.
The vehicle could otherwise start moving immediately (in some
cases even if the parking brake is engaged) and possibly cause an
accident.
•
To avoid accidents, apply the parking brake and put the
selector lever in position P before opening the bonnet and working
on the vehicle with the engine running. Please observe the important safety warnings ⇒ page 255, “Working on components in the
engine compartment”.
Note
You can select the sport program for gear changes on vehicles with
Audi drive select* by activating the DYNAMIC mode. There is no S
position on the selector lever.
•
•
Applies to vehicles with tiptronic gearbox:
If the lever is moved accidentally to N when driving, release the
accelerator and let the engine speed drop to idling before selecting
D or S again.
•
For the sake of fuel economy (and the environment), the gearbox
ratios on some models are designed so that maximum speed is only
obtained when the selector lever is at position S.
document_0900452a81b1b9de.book Seite 165 Donnerstag, 26. Juli 2007 9:16 09
Automatic gearbox
Applies to vehicles: with multitronic® or tiptronic
Selector lever lock
The selector lever lock prevents gears from being
engaged inadvertently, so that the vehicle is not set in
motion unintentionally.
165
makes it possible, for instance, to “rock” the vehicle backwards and
forwards if it is stuck in snow or mud. The selector lever lock
engages automatically if the brake pedal is not depressed and the
lever is in position N for more than about a second.
Interlock button
The interlock button on the selector lever handle prevents the driver
from inadvertently engaging particular gears. Press the button in to
disengage the selector lever lock. The illustration shows the selector
lever positions in which the button has to be pressed, highlighted in
colour ⇒ fig. 179.
Safety interlock for ignition key
Fig. 179 Selector lever
lock functions
The key can only be withdrawn with the ignition switched off and
the selector lever in position P. When the ignition key is removed,
the selector lever is locked in position P.
Applies to vehicles: with multitronic® or tiptronic
The selector lever lock is released as follows:
Kick-down feature
– Switch on the ignition.
– Press the brake pedal and at the same time press in the
interlock button.
Automatic selector lever lock
The selector lever is locked in the P and N positions when the ignition is on. The brake pedal must be depressed before the lever can
be moved out of either of these positions. The following message
appears in the instrument display as a reminder for the driver when
the selector lever is in position P or N:
WHEN STATIONARY APPLY FOOTBRAKE WHILE SELECTING GEAR.
The selector lever lock only works if the vehicle is stationary or
driving at speeds up to 5 km/h. At higher speeds the selector lever
lock in the N position is disengaged automatically.
The kick-down feature is designed to give maximum
acceleration.
Applies to vehicles with multitronic® gearbox
When the accelerator pedal is pressed right down past the point of
resistance at full throttle, the gearbox will select a lower gear ratio,
depending on road speed and engine speed. While you keep the
accelerator depressed the engine speed is automatically controlled
to give your vehicle maximum acceleration.
Applies to vehicles with tiptronic gearbox
When the accelerator pedal is pressed right down past the point of
resistance at full throttle, the gearbox will shift down to a lower
gear, depending on road speed and engine speed. The upshift to the
next higher gear is delayed until the engine reaches maximum rpm.
The selector lever lock is not engaged if the selector lever is moved
quickly through position N (e.g. when shifting from R to D). This
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 166 Donnerstag, 26. Juli 2007 9:16 09
166
Automatic gearbox
WARNING
Please note that if the road surface is slippery or wet, the kickdown feature could cause the driving wheels to spin, which could
result in skidding.
Vehicles with tiptronic gearbox: The gearbox adapts the gearshifts
for uphill and downhill gradients. This prevents the gearbox from
shifting up and down unnecessarily on uphill gradients.
Applies to vehicles: with multitronic® or tiptronic
Manual gear selection (tiptronic mode)
Applies to vehicles: with multitronic® or tiptronic
Dynamic gear control program (DCP)
With the manual shift programme (tiptronic) the driver
can manually select pre-programmed gears.
The automatic gearbox is controlled electronically.
The vehicle is equipped with an electronically controlled gearbox.
The gear ratios are selected automatically according to preset gearshift programmes.
When you drive at moderate speeds the gearbox will select the most
economical shift programme. It will then change up early and delay
the downshifts to give better fuel economy.
If you drive at higher speeds with heavy acceleration, if you open the
throttle quickly, or if you use the kick-down or the car's maximum
speed, the gearbox will automatically select the more “sporty” shift
programmes.
The gearbox is self-adapting, and continuously selects the most
suitable shift programme. At the same time, the driver can also
make the gearbox switch to a more "sporty" programme by pressing
the accelerator quickly. Depending on road speed, this makes the
gearbox shift down early into a lower gear ratio for more rapid acceleration (for instance to pass another vehicle), without having to
press the accelerator all the way down into the kick-down position.
After the gearbox has shifted back up it returns to the original
programme, depending on your style of driving.
Vehicles with multitronic® gearbox: The gearbox continuously
adapts the gear ratios on uphill gradients. If the brake pedal is
pressed on a downhill gradient the gearbox automatically shifts to
a lower gear ratio. This increases the engine braking effect.
Fig. 180 Centre
console: Manual gear
selection (tiptronic
mode)
Fig. 181 Display:
Manual gear selection
(tiptronic mode)
Switching over to the manual programme
– From position D, push the selector lever to the right. As
soon as the automatic gearbox has changed over to this
programme, the display will show the selected gear.
document_0900452a81b1b9de.book Seite 167 Donnerstag, 26. Juli 2007 9:16 09
Automatic gearbox
Shifting up a gear
– Briefly push the selector lever forwards (in the tiptronic
+ .
gate) ⇒ page 166, fig. 180 A
Shifting down a gear
of the display panel either lighting up together or going out
completely.
It is still possible to move the selector lever to all positions. The
manual shift programme (tiptronic) is not available when the backup programme is active.
With the tiptronic system the driver can manually choose between
7 different pre-programmed gears. The manual programme can be
selected either with the vehicle stationary or on the move.
Vehicles with tiptronic gearbox: When the selector lever is in position D or S or in the manual shift programme, the gearbox will
remain in 3rd gear if 1st, 2nd or 3rd gears were engaged when the
fault occurred. The gearbox will remain in 5th gear if 4th, 5th or 6th
gears were engaged. The gearbox will then engage 3rd gear when
you drive away from a standstill or after the engine is restarted.
When accelerating, the gearbox automatically shifts up into the next
gear shortly before the maximum engine speed is reached.
It will still be possible to use reverse gear in the normal way.
However, the electronic lock for reverse gear will be switched off.
– Briefly pull the selector lever backwards (in the tiptronic
– .
gate) A
If you select a gear which is lower than the gear shown in the instrument display ⇒ page 166, fig. 181, the gearbox will only shift down
when there is no longer a risk of overrevving the engine.
When the vehicle slows down (for instance when braking), the
gearbox automatically shifts down into the next gear when the
minimum engine speed is reached.
Changing down to a lower gear increases the engine braking effect
on downhill gradients.
When the accelerator pedal is pressed right down past the point of
resistance at full throttle, the gearbox will select a lower gear,
depending on road speed and engine speed.
167
Caution
Should the gearbox ever switch into the back-up programme, you
should take the vehicle to an Audi dealer or qualified workshop as
soon as possible.
Applies to vehicles: Paddle levers
Steering wheel with paddle levers
The paddle levers on the steering wheel enable the driver
to manually select pre-programmed ratios or gears.
Applies to vehicles: with multitronic® or tiptronic
Back-up programme
A back-up system is in place should a fault occur in the
control system.
The automatic gearbox switches to the back-up programme if a fault
should occur in the control system. This is indicated by all segments
Controls
Safety
Driving tips
Fig. 182 Steering
wheel: tiptronic
switches
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 168 Donnerstag, 26. Juli 2007 9:16 09
168
Automatic gearbox
– to change down
– Briefly pull the left-hand paddle lever A
to a lower gear.
+ to change up
A
– Briefly pull the right-hand paddle lever
to a higher gear.
The paddle levers are activated when the selector lever is in position
D or S, or the position for the manual shift programme (tiptronic).
Fig. 184 Manual
release of selector
lever
The manual shift programme can, of course, still be operated using
the selector lever in the centre console.
The manual release mechanism is behind the ashtray.
Applies to vehicles: with multitronic® or tiptronic
Manual release of selector lever
– Slide open the cover for the ashtray.
The selector lever can be released manually if the electrical power supply should fail.
– Slide the switch
ashtray.
A ⇒ fig. 183 to the right to release the
A
– Take out the ashtray
B .
A
– You will now see a small cover cap at the front of the
opening in the ashtray mounting unit.
– Loosen and remove this cover cap.
– Use a screwdriver or similar object to press down the pin,
which is now accessible, and hold it down ⇒ fig. 184.
Fig. 183 Removing
ashtray
– Now press the interlock button on the selector lever and
move the selector lever to position N.
The selector lever can only be moved out of position P if the ignition
key is inserted and the ignition is switched on. If the power supply
should ever fail (discharged battery, etc.) and the vehicle has to be
pushed or towed, the selector lever must first be moved to
position N. This is possible after operating the manual release
mechanism.
document_0900452a81b1b9de.book Seite 169 Donnerstag, 26. Juli 2007 9:16 09
Parking aid
169
Parking aid
Applies to vehicles: with Audi parking system/plus/advanced
General notes
Rear
Various systems are available to help you when parking or manoeuvring in tight spaces, depending on the equipment fitted on your
vehicle.
The Audi parking system gives an acoustic warning if there are any
obstacles behind the car ⇒ page 169.
When you are parking, the Audi parking system plus warns you
acoustically and optically about obstacles in front of and behind the
vehicle ⇒ page 170.
In conjunction with a reversing camera, the Audi parking system
advanced shows a picture of the area behind the vehicle. This
picture helps you to manoevre the vehicle backwards and sideways.
In addition, you are assisted by the acoustic signals and graphic
display of the parking aid ⇒ page 171.
Note
To ensure that the acoustic parking aid works properly, the sensors
must be kept clean and free of snow and ice.
Audi parking system
Side
0.60 m
Centre
1.60 m
The acoustic signals sound with increasing frequency as you
approach the obstacle. A warning tone will sound continuously
when the vehicle is less than approx. 0.30 m away from the obstacle.
Stop reversing immediately!
The volume of the warning beeps will be gradually reduced after
about 4 seconds if the vehicle remains at a constant distance from
a detected obstacle (it will not be reduced if the obstacle is closer
than 0.30 m).
The parking aid is switched on automatically when reverse gear is
engaged. You will hear a brief acknowledgement tone.
WARNING
•
The parking aid cannot replace the full concentration of the
driver. The driver is always responsible for safety during parking
and other manoeuvres.
•
The sensors have blind spots in which obstacles are not registered. It is particularly important to ensure that there are no small
children or animals near the vehicle, as the sensors may not
always be able to detect them.
•
Always keep a close watch on the area around the vehicle and
make full use of the rear-view mirrors.
Applies to vehicles: with Audi parking system
Description
The Audi parking system is an acoustic parking aid.
Sensors are located in the rear bumper. When the sensors detect an
obstacle, you are alerted by acoustic signals (beeps). The measuring
range of the sensors starts at about:
Controls
Safety
Driving tips
Caution
Please note that low obstacles detected by the system may no
longer be registered by the sensors as the car moves closer, so the
system will not give any further warning. Certain kinds of obstacles
(such as wire fences, chains, thin painted posts or trailer draw bars,
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 170 Donnerstag, 26. Juli 2007 9:16 09
170
Parking aid
etc.) may not always be detected by the system, so take care not to
damage the vehicle in such cases.
•
•
Applies to vehicles: with Audi parking system plus
Switching on/off
Note
Please refer to the notes on towing ⇒ page 177.
You can adjust the volume and pitch of the beeps ⇒ page 177.
Audi parking system plus
Fig. 185 Centre
console: Parking aid
switch
Applies to vehicles: with Audi parking system plus
Description
The Audi parking system plus is a parking aid with
acoustic signals and graphic display.
Sensors are located in the front and rear bumpers. When the
sensors detect an obstacle, you are alerted by acoustic signals
(beeps) and a graphic display. The measuring range of the sensors
starts at about:
Front
Rear
Side
0.90 m
Centre
1.20 m
Side
0.60 m
Centre
1.60 m
The acoustic signals sound with increasing frequency as you
approach the obstacle. A warning tone will sound continuously
when the vehicle is less than approx. 0.30 m away from the obstacle.
Stop moving immediately!
The volume of the warning beeps will be gradually reduced after
about 4 seconds if the vehicle remains at a constant distance from
a detected obstacle (it will not be reduced if the obstacle is closer
than 0.30 m).
Fig. 186 Display:
Graphical distance
display
Switching on
– Switch on the sound system or MMI*.
– Engage reverse gear, or
– Press the switch  in the centre console ⇒ fig. 185 or
next to the selector gate. You will hear a brief acknowledgement tone and the diode in the switch will light up.
Switching off
– Drive forwards faster than 10 km/h, or
document_0900452a81b1b9de.book Seite 171 Donnerstag, 26. Juli 2007 9:16 09
Parking aid
•
•
– Press the switch , or
– Switch off the ignition.
Segments in the graphic display
You can estimate the distance to an obstacle by referring to the red
segments at the front and rear of the vehicle ⇒ page 170, fig. 186.
The closer the vehicle gets to the obstacle the closer the segments
move towards the vehicle in the graphic. At the latest when the
penultimate segment is highlighted the vehicle has reached the
danger (collision) zone. Stop moving immediately ⇒
!
171
Please refer to the notes on towing ⇒ page 177.
There is a slight delay in the picture display.
Audi parking system advanced
Applies to vehicles: with Audi parking system advanced
Introduction
WARNING
•
The parking aid cannot replace the full concentration of the
driver. The driver is always responsible for safety during parking
and other manoeuvres.
•
The sensors have blind spots in which obstacles are not registered. It is particularly important to ensure that there are no small
children or animals near the vehicle, as the sensors may not
always be able to detect them.
Fig. 187 Viewed from
above: Parking mode 1
•
Always keep a close watch on the area around the vehicle and
make full use of the rear-view mirrors.
Caution
Please note that low obstacles detected by the system may no
longer be registered by the sensors as the car moves closer, so the
system will not give any further warning. Certain kinds of obstacles
(such as wire fences, chains, thin painted posts or trailer draw bars,
etc.) may not always be detected by the system, so take care not to
damage the vehicle in such cases.
•
Note
You can change the display and adjust the volume and pitch of
the beeps ⇒ page 177.
Controls
Safety
Driving tips
Fig. 188 Viewed from
above: Parking mode 2
A reversing camera is integrated in vehicles with the Audi parking
system advanced, in addition to a parking aid with acoustic signals
and graphic display ⇒ page 170.
Two modes can be selected when parking. “Parking mode 1” can, for
example, be used when parking your vehicle in a parking bay or a
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 172 Donnerstag, 26. Juli 2007 9:16 09
172
Parking aid
garage ⇒ fig. 187. Select “parking mode 2” if you wish to park
parallel to the roadside ⇒ fig. 188.
Applies to vehicles: with Audi parking system advanced
General notes
Applies to vehicles: with Audi parking system advanced
Description
Fig. 191 Boot lid: Location of reversing
camera
Fig. 189 Viewed from
above: Area covered by
the reversing camera
We recommend that you practise parking with the reversing camera
in a quiet location (car park or similar) in order to become familiar
with the system, including the orientation lines and all the other
features. Ideally, the weather and light conditions should be good.
Vehicles or other objects shown in the MMI display appear to be
further away or closer, if:
•
you are reversing from a horizontal surface up a gradient or
down a hill,
1 :
Fig. 190 Side view: A
Area covered by the
2 :
reversing camera; A
area NOT covered by
the reversing camera
The reversing camera covers approximately the area depicted in
1 . This is the area you will see in the
⇒ fig. 189 and ⇒ fig. 190 A
picture on the MMI display. Orientation lines and colour markings
are projected onto the picture to help you when parking or mano2
evring in tight spaces. Objects out of range of the camera in area A
do not appear in the picture on the MMI display.
•
•
you are reversing towards protruding objects,
the vehicle has been loaded with a greater load on the rear.
The accuracy of the orientation lines and the blue area markings
decreases if:
•
the reversing camera does not provide a reliable image, e.g. if
visibility is poor or the lens is dirty,
•
the sun is so dazzling that you cannot see the image on the
display screen.
How to clean the lens of the reversing camera
The reversing camera is located above the rear number plate. To
ensure that the parking aid works properly, the lens ⇒ fig. 191 must
be kept clean.
document_0900452a81b1b9de.book Seite 173 Donnerstag, 26. Juli 2007 9:16 09
Parking aid
•
Moisten the lens using a commercially available, alcohol-based
glass cleaning agent and clean the lens with a dry cloth ⇒ .
•
Use a small brush to remove snow and a de-icer spray to remove
ice ⇒ .
WARNING
Applies to vehicles: with Audi parking system advanced
Switching on/off
The reversing camera is automatically switched on
together with the acoustic signals and graphic display
when you select reverse gear.
•
Switching on
•
– Engage reverse gear, or
The parking aid cannot replace the full concentration of the
driver. The driver is always responsible for safety during parking
and other manoeuvres.
Always keep a close watch on the area around the vehicle and
make full use of the rear-view mirrors.
•
Do not allow the camera images in the MMI display to distract
you from watching the traffic.
•
For safety reasons, you should not use the system if the position and installation angle of the camera have been changed, e.g.
in a rear-end collision. Have it checked by a qualified workshop.
173
– Switch on the MMI system.
– Press the switch  in the centre console ⇒ page 170,
fig. 185. You will hear a brief acknowledgement tone and
the diode in the switch will light up.
Switching off
– Drive forwards faster than 10 km/h, or
– Press the switch , or
•
Caution
– Switch off the ignition.
Please note that low obstacles detected by the system may no
longer be registered by the sensors as the car moves closer, so the
system will not give any further warning. Certain kinds of obstacles
(such as wire fences, chains, thin painted posts or trailer draw bars,
etc.) may not always be detected by the system, so take care not to
damage the vehicle in such cases.
•
Never remove snow and ice from the lens of the reversing
camera using warm or hot water - danger of cracks appearing on the
lens.
•
Changing display via MMI
– Press the control button for Graphic ⇒ page 174, fig. 192
5 to show the graphic display on the screen.
A
– Press the control button for Rear View to display the
picture from the reversing camera.
WARNING
Never use abrasive cleaning agents on the lens.
•
Some objects (e.g. narrow posts or bars), recesses in the
ground or protruding parts on other vehicles may not be displayed
in a satisfactory manner or may not be displayed at all on the MMI
screen.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 174 Donnerstag, 26. Juli 2007 9:16 09
174
Parking aid
Applies to vehicles: with Audi parking system advanced
WARNING (continued)
•
Only use the reversing camera to assist you if it is supplying
you with a good and clear picture. The quality of the picture could
be impaired by adverse light, dirt on the lens or a defect (accident
risk).
Parking perpendicular to the roadside
Parking mode 1 can be used when parking your vehicle in
a garage or parking bay.
•
Only use the reversing camera when the boot lid is completely
closed. Please make sure that there are no objects mounted to the
rear end of the vehicle which could block the view of the reversing
camera.
•
Note
If your vehicle is near an obstacle, the graphic display will also
appear in the reversing camera image. This superimposed graphic
helps the driver to localise the critical area of the vehicle.
Fig. 192 MMI display:
Approaching a parking
space
•
You can change the display and adjust the volume and pitch of
the beeps ⇒ page 177.
•
•
Please refer to the notes on towing ⇒ page 177.
There is a slight delay in the picture display.
Fig. 193 MMI display:
Aligning the vehicle
– Turn the steering wheel until the orange orientation lines
1 are pointing towards the parking space ⇒ fig. 192.
A
You can estimate the distance to an obstacle by referring
2 . Each marking is equivalent to
to the markings A
1 metre.
document_0900452a81b1b9de.book Seite 175 Donnerstag, 26. Juli 2007 9:16 09
Parking aid
– Reverse into the space and adapt the steering angle to
the parking space, using the orange lines to assist you
3 indicates the rear bumper. You should stop
⇒
.A
4
reversing, at the latest, when the red orientation line A
is bordering on an object ⇒
!
175
Applies to vehicles: with Audi parking system advanced
Parking parallel to the roadside
Parking mode 2 can be used when parking your vehicle at
the roadside.
– Align your vehicle according to the blue area marking
⇒ fig. 193. The blue marking is an extension of the
vehicle outline and reaches about five metres to the rear
of the vehicle. The shade of blue changes at a distance of
approx. 1 m, 2 m and 5 m to the vehicle.
Fig. 194 MMI display:
Blue area marking
aligned in parking
space
WARNING
•
The reversing camera does not show the complete area behind
the vehicle. It is particularly important to ensure that there are no
small children or animals near the vehicle, as the reversing camera
may not always be able to detect them (accident risk).
•
Please note that objects which are not touching the ground
may appear to be further away than they actually are (e.g. the
bumper of a parked vehicle, a towing bracket or the rear end of a
truck). In this case you should not use the orientation lines as a
guide when parking the car - accident risk!
Fig. 195 MMI display:
Blue marking touches
edge of pavement
Caution
The MMI display shows the path of the rear end of the vehicle if you
were to reverse using the current steering angle. NB: The front end
of the vehicle swings out further than the rear. Please make sure you
keep a sufficient distance between the vehicle and any obstacles to
make sure that the exterior mirror or edge of the vehicle do not
collide with the obstacle (accident risk).
The following steps apply only when there are no obstacles
(such as a wall) next to the parking space. Otherwise, please
follow the “Instructions for parking next to obstacles”.
– Position your vehicle parallel to the roadside, about a
metre away from the next parked vehicle.
– Engage reverse gear. The parking aid will be switched on
and parking mode 1 will be displayed.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 176 Donnerstag, 26. Juli 2007 9:16 09
176
Parking aid
1 on the
– Press the control button for Mode ⇒ fig. 194 A
MMI control console. Parking mode 2 is displayed.
– Reverse and align your vehicle in such a way that the blue
2 borders onto the vehicle behind or onto
area marking A
the parking space line marking. The blue marking is an
extension of the vehicle outline and reaches about five
metres to the rear of the vehicle. The long side of the blue
marking should border onto the kerb. The complete blue
area marking must fit into the parking space.
– When the vehicle is stationary turn the steering wheel to
the left as far as it will go.
– Reverse into the parking space.
– Stop the vehicle as soon as the blue curve touches the
kerb ⇒ page 175, fig. 195.
– When the vehicle is stationary turn the steering wheel to
the right as far as it will go.
– Continue to reverse into the parking space until the
3 indicates the
vehicle is standing parallel to the kerb. A
rear bumper. You should stop reversing, at the latest,
4 is bordering on an
when the red orientation line A
object ⇒
! Keep a close watch on the front of your
vehicle ⇒
.
Parking next to obstacles
If an obstacle (such as a wall) is located next to the parking space,
the clearance at the side of the vehicle must be larger. Position the
long side of the blue marking so that there is sufficient clearance
from the kerb. The marking must not touch the kerb. You must also
start turning the steering wheel much earlier. The blue curve
⇒ page 175, fig. 195 must not touch the kerb - make sure there is
sufficient clearance from the kerb.
WARNING
•
The reversing camera does not show the complete area behind
the vehicle. It is particularly important to ensure that there are no
small children or animals near the vehicle, as the reversing camera
may not always be able to detect them (accident risk).
•
Please note that objects which are not touching the ground
may appear to be further away than they actually are (e.g. the
bumper of a parked vehicle, a towing bracket or the rear end of a
truck). In this case you should not use the orientation lines as a
guide when parking the car - accident risk!
Caution
The MMI display shows the path of the rear end of the vehicle if you
were to reverse using the current steering angle. NB: The front end
of the vehicle swings out further than the rear. Please make sure you
keep a sufficient distance between the vehicle and any obstacles to
make sure that the exterior mirror or edge of the vehicle do not
collide with the obstacle (accident risk).
Note
The orientation lines and markings appear on the left or right side,
depending on which turn signals are on.
document_0900452a81b1b9de.book Seite 177 Donnerstag, 26. Juli 2007 9:16 09
Parking aid
•
•
Applies to vehicles: with Audi parking system/plus/advanced
Switching display and acoustic
signals on and off
177
Front volume* - Volume of the front sensors
Front frequency* - Pitch of the front sensors
You will hear a short test tone each time you make a new setting.
The settings for the graphic display* and acoustic signals
are controlled via the sound system or MMI*.
•
Note
You can also change the warning beep settings directly from the
graphic display* or reversing camera* picture. Simply press the
control button for Settings *.
•
New settings are not activated until you switch on the parking
aid again.
•
The settings will be automatically stored and assigned to the
remote control key.
Fig. 196 Display:
Settings for parking
aid
– Select: Function selector button CAR > Audi parking
system.
Display*
•
off - The parking aid gives only acoustic warning signals when it
is activated.
•
Graphic - The graphic display appears when reversing and
driving forwards.
Applies to vehicles: with Audi parking system/plus/advanced and towing bracket
Towing bracket
In towing mode, the rear parking sensors are NOT activated when
you select reverse gear or press the switch . This may not apply if
the power socket was NOT factory-fitted. This results in the
following restrictions:
Audi parking system*
There is no distance warning.
•
Audi parking system plus*
•
There is no rear distance warning. However, the system will still give
a warning when obstacles are detected while driving forwards. The
proximity graphic will switch over to towing mode.
Rear View* - The picture from the reversing camera is shown
when reversing and driving forwards.
Automatic* - The picture from the reversing camera is shown
when reversing and the graphic display is shown when driving
forwards.
Warning beeps
•
•
There is no rear distance warning. However, the system will still give
a warning when obstacles are detected while driving forwards. The
proximity graphic will switch over to towing mode. The image of the
Rear volume - Volume of the rear sensors
Rear frequency - Pitch of the rear sensors
Controls
Safety
Audi parking system advanced*
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 178 Donnerstag, 26. Juli 2007 9:16 09
178
Parking aid
reversing camera will then be shown without orientation lines and
blue area markings.
Applies to vehicles: with Audi parking system/plus/advanced
Error messages
If you hear a long beep for a few seconds and the diode in the switch
* starts flashing when you switch on the parking aid, a system
fault has occurred. Please have the fault corrected by an Audi dealer
or qualified workshop.
Note
If the fault is not corrected before you switch off the ignition, it will
only be indicated by the flashing diode in the switch * the next
time you switch on the parking aid.
document_0900452a81b1b9de.book Seite 179 Donnerstag, 26. Juli 2007 9:16 09
HomeLink
179
HomeLink
Universal transmitter
•
Applies to vehicles: with HomeLink
Description
The HomeLink universal transmitter can be programmed
to replace the hand-held controls of devices already in
use.
HomeLink allows you to conveniently activate garage doors, estate
gates, security systems, home or office lighting and other electric
devices by means of control buttons inside your car.
Note
For additional information on HomeLink® and/or products
compatible with HomeLink®, please call the toll-free HomeLink®
hotline (0) 08000466 35465 or alternatively +49 (0) 6838 907 277, or
visit the HomeLink® website at: www.homelink.com
•
HomeLink® is a registered trademark of Johnson Controls.
Applies to vehicles: with HomeLink
Programming the universal transmitter
The HomeLink unit is programmed at the radiator grille.
HomeLink can replace up to three hand-held transmitters operating
existing devices on your property with a single universal transmitter. This will be possible for most transmitters which control the
drive units for a garage door or external gates, etc. You can
programme the individual hand-held transmitters for your remote
control at or near the centre of the radiator grille. This is where the
control unit is located.
To be able to control systems with HomeLink, you need to perform
initial programming on the HomeLink transmitter first. If systems
fail to respond after the initial programming, check whether these
systems work with a "rolling code" (variable security code)
⇒ page 180.
Fig. 197 Operating
unit in headliner
WARNING
When you are programming the HomeLink universal transmitter,
make sure that no persons or objects are close to the devices
receiving the transmitter signals. If a gate or door is inadvertently
set into motion during programming, persons might be injured or
other damage caused by moving parts.
Fig. 198 Radiator grille
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 180 Donnerstag, 26. Juli 2007 9:16 09
180
HomeLink
At the operating unit
1. Switch on the ignition (do not start the engine).
2. Press and hold down the two outer HomeLink buttons
A
⇒ page 179, fig. 197 until the indicator diode A
⇒ page 179, fig. 197 begins to flash after about
20 seconds. This procedure will delete the standard
factory settings and does not need to be repeated when
programming the other buttons.
3. Press the particular HomeLink button which you would
like to program.
A begins to flash. The HomeLink
4. Wait until the diode A
module now remains in training mode for 5 minutes.
5. Now step in front of your vehicle with the original handheld transmitter for the garage door opener or any other
device you wish to assign to the HomeLink control
button.
The proper distance between the hand-held transmitter and the
HomeLink module at the radiator grille depends on the system you
want to train. It may require several attempts.
The turn signals will flash once if the time limit for the programming
mode has been exceeded. In this case the programming procedure
needs to be performed again. Repeat the sequence at the operating
unit starting with step 3.
The programming instructions above also apply to the other control
buttons. Start with step 3 if you wish to proceed and program the
other two buttons.
If the garage door or other devices still fail to be activated with the
HomeLink control buttons after programming is completed, it is
possible that these systems might be working with a rolling code
instead of the normal fixed security code. If this is the case, a rolling
code programming is required in addition to the steps described
above. ⇒ page 180
Applies to vehicles: with HomeLink
Rolling code programming
At the radiator grille
6. Hold the original hand-held transmitter at or near the
centre of your car's radiator grille ⇒ page 179, fig. 198.
7. Press the activator button on the original hand-held
transmitter.
8. As you do so, watch the turn signals on your vehicle.
HomeLink confirms successful programming by flashing
all four turn signals three times.
9. If the turn signals fail to flash three times, repeat the
procedure with the transmitter held at a different
distance from the radiator grille.
Some devices require rolling code programming of the
HomeLink universal transmitter.
Identifying a rolling code
– Press the already programmed HomeLink button again
and hold it down.
A ⇒ page 179, fig. 197. If the
– Watch HomeLink diode A
diode starts flashing rapidly and turns into a constant
light after about 2 seconds, this indicates that the device
you wish to operate (e.g. a garage door opener) is
equipped with a rolling code.
– Program the rolling code as follows:
document_0900452a81b1b9de.book Seite 181 Donnerstag, 26. Juli 2007 9:16 09
HomeLink
Activating the garage door opener drive unit
Applies to vehicles: with HomeLink
– Locate the programming button on the garage door
drive. The exact location and colour of the button may
vary depending on the type of garage door opener.
Operating HomeLink
– Press the programming button on the door drive unit
(this will normally cause a “programming mode indicator
lamp” on the unit to light up). You now have about 30
seconds to start and complete the programming of the
HomeLink control button on the operating unit.
– Make sure that the ignition is on.
Programming at the operating unit in the
headliner
– Press and release the already programmed HomeLink
button.
– Press the HomeLink button again to complete rolling
code programming.
After programming at the operating unit in the headliner, the
garage door opener should recognize the HomeLink signal and
respond when the HomeLink button is pressed. Now the other
control buttons can be programmed as required.
•
181
The programmed devices are activated by means of the
HomeLink control buttons in the headliner.
– Press the programmed HomeLink button ⇒ page 179,
fig. 197. The device assigned to that button (e.g. garage
door) will be activated.
The HomeLink indicator diode ⇒ page 179, fig. 197 will light up
when you press the button.
Applies to vehicles: with HomeLink
Erasing the button programming
You can erase the complete HomeLink programming by
pressing the two outer buttons.
– Switch on the ignition (do not start the engine).
– Press and hold down the two outer buttons until the indicator diode starts to flash ⇒ page 179, fig. 197.
– Then release the buttons.
Note
Having a second person assist you makes programming of the
rolling code easier and faster. For some makes of garage door
openers the HomeLink button may have to be pressed a third time
to complete the training sequence.
• If you encounter problems programming the rolling code you
may find helpful information in the operating instructions of the
garage door opener or other device you wish to operate.
After the programming of the HomeLink buttons has been erased,
the system will return to the training mode and is ready to be reprogrammed at any time.
•
•
Note
Programmed buttons cannot be erased individually.
For security reasons it is advisable to erase the programming of
the HomeLink buttons prior to selling your vehicle.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 182 Donnerstag, 26. Juli 2007 9:16 09
182
HomeLink
Applies to vehicles: with HomeLink
Re-programming a button
A HomeLink button can be re-programmed individually
without affecting the other button allocations.
least 15 seconds before trying again with the transmitter in a
different position. Keep watching the turn signals during that
time.
Applies to vehicles: with HomeLink
At the operating unit in the headliner
– Press and hold down the selected button until the indicator diode ⇒ page 179, fig. 197 starts flashing slowly.
Conformity certification
The HomeLink universal transmitter is registered in the following
countries under the following certification numbers:
At the radiator grille
Country
Certification number
Andorra
16SEP2003
Belgium
RTT/D/X2064
Denmark
98.3142-266
Germany
D800038K
Finland
FI98080106
France
97619 RD
Gibraltar
RTTE 20754/0087847
Greece
JCI 05JUL2000 RTTE
– If the turn signals fail to flash three times, repeat the
procedure with the transmitter held at a different
distance from the radiator grille.
Great Britain
RTTE 20754/0087847
Republic of Ireland
TRA 24/5/109/5
Iceland
IS-3418-00
When the turn signals have flashed three times, this means the
device previously stored in HomeLink has been erased and the new
system programmed in its place. To activate the new system, press
the HomeLink button that has just been re-programmed.
Italy
DGPGF/4/341032/TB 0002573
Croatia
SRD-156/03
Luxembourg
L2433/10510-03J
Malta
WT/122/98
Monaco
PC/cp-CI.T55-03/04672
Netherlands
NL99030970
Norway
NO20000026
– Hold the original hand-held transmitter for the garage
door opener or other device directly in front of the radiator grille of your vehicle (at or near the centre)
⇒ page 179, fig. 198. The exact distance depends on the
system that you want to program.
– Press the button on the original hand-held transmitter
for the garage door opener or other device.
– As you do so, watch the turn signals on your vehicle.
HomeLink confirms successful programming by flashing
all four turn signals three times.
Note
It may require several attempts before programming is successful.
When programming a new device, keep the button pressed for at
document_0900452a81b1b9de.book Seite 183 Donnerstag, 26. Juli 2007 9:16 09
HomeLink
Country
Certification number
Austria
GZ104569-ZB/98
Poland
URT-GP-CLBT-431-66/2002/C
Portugal
JCI 03JUL2000 RTTE
Sweden
Ue990195
Switzerland
BAKOM 98.0746.K.P
Slovak Republic
R 267 2001 N
Spain
0416 00
Czech Republic
CTU 2000 3 R 1194
Turkey
0425/TGM-TR/JOCO-EURO
Hungary
BB-5793-1/2000
Cyprus
MCW129/95 12/2000
Controls
Safety
Driving tips
General maintenance
Self-help
183
Technical data
document_0900452a81b1b9de.book Seite 184 Donnerstag, 26. Juli 2007 9:16 09
184
document_0900452a81b1b9de.book Seite 185 Donnerstag, 26. Juli 2007 9:16 09
Safety
185
document_0900452a81b1b9de.book Seite 186 Donnerstag, 26. Juli 2007 9:16 09
186
Safe driving
Safe driving
General notes
Safety is the first priority
Your safety is our first priority.
This chapter contains important information, tips, suggestions and warnings that you should read and observe for
your own safety and the safety of your passengers.
WARNING
•
The information in this chapter is important for the driver of
the vehicle and all passengers. The other chapters in this manual
(and, where applicable, in the other literature supplied with the
vehicle) contain further important notes which you should read
and observe for your own safety and that of your passengers.
•
Ensure that the complete vehicle wallet is always in the vehicle.
This is especially important when you lend or sell the vehicle to
others.
Safety features
The safety features listed here are part of the vehicle's
occupant restraint system. They work together to help
reduce the risk of injury in a wide variety of accident situations.
Your safety and the safety of your passengers should not be left to
chance. In the event of an accident, the safety features incorporated
in your vehicle are capable of reducing the risk of injury. These are
just a few of the safety features in your Audi:
•
Optimised three-point seat belts for all seats,
•
•
•
•
•
•
Belt force limiters for the front seats,
Belt pre-tensioners for the front seats,
Head restraints for all seats,
Optimised protection against injuries of the cervical vertebrae,
Front airbags,
Side airbags in the front seat backrests and on the outer rear
seats*,
•
•
Head-protection airbags (sideguard system),
“ISOFIX” mountings* for “ISOFIX” child safety seats on the rear
seats,
•
•
Height-adjustable head restraints on the seats,
Adjustable steering column.
These individual safety features are harmonised to provide you and
your passengers with the best possible protection in accident situations. However, they can only be effective if you and your passengers sit in the correct position and adjust and use the safety equipment properly.
For these reasons, this chapter explains why these safety features
are so important, how they can protect you, what you need to
remember when using them, and how you and your passengers can
gain the most benefit from them. There are also a number of important safety warnings which you and your passengers should always
observe in order to minimise the risk of injury.
Safety is everyone's responsibility!
document_0900452a81b1b9de.book Seite 187 Donnerstag, 26. Juli 2007 9:16 09
Safe driving
Before every trip
What affects driving safety?
The driver is responsible for the safety of the passengers
and the safe operation of the vehicle at all times.
Safety on the road is directly related to how you drive, and
can also be affected by the passengers in the vehicle.
For your own safety and the safety of your passengers,
always note the following points before every trip:
The driver is responsible for the safety of the vehicle and all
its occupants. If your ability to drive is impaired in any way,
you endanger yourself and other road users ⇒
. Therefore:
– Make sure that all lights and turn signals are working
properly.
– Do not let yourself be distracted by passengers or by
using a mobile phone, etc.
– Check the tyre pressures.
– Make sure that all windows are clean and give good visibility to the outside.
– Secure all luggage and other items carefully ⇒ page 79.
– Never drive when your driving ability is impaired (by
medication, alcohol, drugs, etc.).
– Make sure that no objects can interfere with the pedals.
– Obey all traffic regulations and speed limits and always
maintain a safe distance to the vehicle in front.
– Adjust the front seat, head restraint and mirrors
correctly.
– Always adjust your speed to suit the road, traffic and
weather conditions.
– Make sure that the head restraints for all passengers are
adjusted to the correct position.
– Take frequent breaks on long trips. Do not drive for more
than two hours without a stop.
– Make sure that children are protected with suitable
safety seats and properly worn seat belts ⇒ page 210.
– If possible, avoid driving when you are tired or stressed.
– Sit in the correct position in your seat and make sure that
your passengers do the same. ⇒ page 73.
– Fasten your seat belt correctly. Make sure that your
passengers do the same ⇒ page 194.
Controls
187
Safety
Driving tips
WARNING
•
Distractions while driving or any kind of impairment to your
driving ability increase the risk of accident and injury.
•
Do not store loose objects on the dashboard. These objects
could fly around the interior when the vehicle is moving (under
acceleration or whilst cornering) and distract the driver – this
could lead to an accident.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 188 Donnerstag, 26. Juli 2007 9:16 09
188
Safe driving
Correct sitting positions
Correct sitting position for driver
– Move the driver's seat forwards or backwards so that you
can press the accelerator, brake and clutch pedals all the
way to the floor with your knees slightly bent ⇒
.
The correct driving position is important for safe and
fatigue-free driving.
– Make sure that you can comfortably reach the top of the
steering wheel.
– Adjust the head restraint so that the top of the head
restraint is level with the top of your head ⇒ fig. 200.
– Adjust the backrest to an upright position so that your
back remains in contact with the upholstery.
– Fasten your seat belt correctly ⇒ page 194.
Fig. 199 Minimum
distance between
driver and steering
wheel
– Keep both feet in the footwell so that you are in full
control of the vehicle at all times.
For detailed information on how to adjust the driver's seat, see
⇒ page 73, “Seats and storage”.
WARNING
•
A driver who is not sitting in the correct position or who is not
wearing a seat belt can be fatally injured if the airbag is triggered.
•
Fig. 200 Correct head
restraint position for
the driver
Adjust the driver's seat so there is a distance of at least 25 cm
between your breastbone and the centre of the steering wheel
⇒ fig. 199.
•
While driving, always hold the steering wheel with both hands
on the outside of the rim at about the 9 o'clock and 3 o'clock position. This reduces the risk of injury if the driver's airbag inflates.
For your own safety, and to reduce the risk of injury in the
event of an accident, we recommend the following driving
position.
•
– Adjust the steering wheel so there is a distance of at least
25 cm between the steering wheel and your breastbone
⇒ fig. 199.
•
Never hold the steering wheel at the 12 o'clock position, or
with your hands inside the rim or on the steering wheel hub. This
could result in serious injuries to the arms, hands and head if the
driver's airbag inflates.
To reduce any risk of injury to the driver during a sudden brake
application or in an accident, never drive with the backrest tilted
document_0900452a81b1b9de.book Seite 189 Donnerstag, 26. Juli 2007 9:16 09
Safe driving
WARNING (continued)
189
WARNING
too far back. The airbag system and seat belts can only provide
proper protection when the backrest is in an upright position and
the driver is wearing the seat belt in the correct position. The
further the backrest is tilted back, the greater the risk of injury due
to incorrect positioning of the belt webbing or an incorrect sitting
position.
•
Adjust the head restraint properly so that it can give maximum
protection.
Correct sitting position for front passenger
The front seat passenger must sit at least 25 cm away
from the dash panel so that the airbag has enough room
to inflate and give maximum protection in an accident.
For your own safety and to reduce the risk of injury in the
event of an accident, we recommend adjusting the front
passenger's seat as follows:
– Move the front passenger's seat as far back as possible
⇒
.
– Adjust the backrest to an upright position so that your
back remains in contact with the upholstery.
– Adjust the head restraint so that the top of the head
restraint is level with the top of your head ⇒ page 190.
– Keep both feet in the footwell in front of the seat.
– Fasten your seat belt correctly ⇒ page 197.
In exceptional cases you can disable the front passenger's airbag
via the key-operated switch* ⇒ page 208.
A passenger who is not sitting in the correct position or who is not
wearing a seat belt can be fatally injured if the airbag is triggered.
•
Adjust the front passenger's seat so there is a distance of at
least 25 cm between your breastbone and the dash panel.
•
Always keep your feet on the floor when the vehicle is moving;
never rest them on the instrument panel, out of the window or on
the seat. If you sit in an incorrect position, you increase your risk
of injury in the event of sudden braking or an accident. If the airbag
is triggered, you could sustain potentially fatal injuries by sitting
out of position.
•
To reduce the risk of injury to the front passenger in the case of
sudden braking or an accident, the passenger should never travel
in a moving vehicle with the backrest reclined. The airbag system
and seat belt can only provide proper protection when the backrest is in an upright position and the passenger is wearing the seat
belt in the correct position. The further the backrest is tilted back,
the greater the risk of injury due to incorrect positioning of the belt
webbing or an incorrect sitting position.
•
Always adjust the head restraints properly for maximum
protection.
Correct sitting position for passengers in the
rear
Rear seat passengers should sit upright with both feet on
the floor and wear their seat belts properly whenever the
vehicle is moving.
To reduce any risk of injury in the event of sudden braking
or an accident, passengers in the rear seats must observe
the following:
For detailed information on how to adjust the front passenger's
seat, see ⇒ page 73, “Seats and storage”.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 190 Donnerstag, 26. Juli 2007 9:16 09
190
Safe driving
– Adjust the head restraint so that the top of the head
restraint is level with the top of your head ⇒ page 190.
– Keep both feet in the footwell in front of the rear seat.
– Fasten your seat belt correctly ⇒ page 197.
– Use appropriate child restraint systems for children travelling in the vehicle ⇒ page 210.
Fig. 202 Correctly
adjusted head restraint
(seen from the side)
WARNING
Rear passengers sitting out of position can suffer severe injuries.
•
Always adjust the head restraints properly for maximum
protection.
•
Seat belts only offer maximum protection when the backrest is
in an upright position and the passengers are wearing the seat
belts properly. By not sitting upright, rear passengers increase the
risk of injury due to incorrect positioning of the seat belt
webbing.
The head restraints must be adjusted properly to provide
maximum protection.
– Adjust the head restraint so that the top of the head
restraint is level with the top of your head ⇒ fig. 201 and
⇒ fig. 202.
For more information on how to adjust the head restraints, see
⇒ page 77.
WARNING
Correct adjustment of head restraints
Properly adjusted head restraints are an important part of
the vehicle's occupant protection system. They can help
to reduce the risk of injuries in most accident situations.
Travelling with the head restraints removed or incorrectly
adjusted increases the risk of severe injuries.
•
Incorrectly adjusted head restraints could lead to death in the
event of a collision or accident.
•
Incorrectly adjusted head restraints can also increase the risk
of injury during sudden or unexpected braking or other manoeuvres.
•
The head restraints must always be adjusted according to the
occupant's size.
Fig. 201 Correctly
adjusted head restraint
(seen from the front)
document_0900452a81b1b9de.book Seite 191 Donnerstag, 26. Juli 2007 9:16 09
Safe driving
Examples of incorrect sitting positions
Occupants can suffer severe or fatal injuries injuries if
they sit in an incorrect position while the vehicle is
moving.
Seat belts can only provide maximum protection if the belt
webbing is positioned correctly. Sitting out of position
greatly reduces the effectiveness of the seat belts and
increases the risk of injury since the belt webbing is not
worn in the position for which it is designed. The driver is
responsible for the safety of all vehicle occupants, especially for children.
– Never allow anyone to sit out of position while the
vehicle is moving ⇒
.
The following list shows just some examples of incorrect sitting
positions which can be dangerous to all occupants. The list is not
complete, but will help to make you aware of possible dangers
which can be avoided.
never ride in the footwell,
never travel on a seat without wearing the seat belt,
never climb into the luggage compartment.
WARNING
Sitting out of position increases the risk of severe injuries.
•
Sitting out of position exposes the occupants to potentially
fatal injuries: if the airbags inflate they can strike any occupant
who is not in one of the designed seat positions.
•
Before starting a trip, sit in the correct position and stay in this
position as long as the vehicle is moving. Before every trip, make
sure all passengers are sitting in the correct positions and remain
correctly seated at all times ⇒ page 73, “Seats and storage”.
Pedal area
Pedals
The pedals must always be free to move and must never
be obstructed by floor mats or any objects in the footwell.
Therefore, whenever the vehicle is moving:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
191
never stand up in the vehicle,
– Make sure that the accelerator, brake and clutch pedals
are not obstructed and can be pressed all the way down
to the floor.
never stand on the seats,
never kneel on the seats,
never travel with the backrest reclined too far,
– Make sure that all pedals are able to return freely to their
original positions.
never lean against the dash panel,
never lie down on the rear seat,
never sit on the front edge of a seat,
Only use floor mats which leave the pedal area free and can be
securely fastened in the footwell.
never sit sideways,
never lean out of the window,
If one of the brake circuits should fail, increased brake pedal travel
will be required to bring the vehicle safely to a stop.
never put your feet out of the window,
never put your feet on the dash panel,
never put your feet on the seat cushion,
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 192 Donnerstag, 26. Juli 2007 9:16 09
192
Safe driving
WARNING
Any obstructions that restrict pedal travel can cause loss of
vehicle control and critical situations on the road.
•
Never place objects in the driver's footwell. Such objects could
move under the pedals and interfere with their proper function. In
the event of sudden braking or a change of direction, you would
not be able to use the pedals. This could result in a loss of control
and possibly cause an accident.
Floor mats on the driver's side
Use only floor mats which can be securely fastened in the
footwell and do not obstruct the pedals.
– Make sure that floor mats are securely fastened and
cannot interfere with the pedals ⇒
.
Use only floor mats that leave the pedal area unobstructed and are
firmly secured to prevent them from slipping. You can obtain suitable floor mats from your dealer or a specialist retailer.
WARNING
Any obstructions that restrict pedal travel can cause loss of
vehicle control and increase the risk of serious personal injury.
•
•
Always make sure that floor mats are properly secured.
Never lay or install additional floor mats or other floor coverings over the existing floor mats; this would restrict the pedal area
and possibly obstruct the pedals, which could cause an
accident.
Stowing luggage safely
Luggage compartment
All luggage and other objects must be safely secured in
the luggage compartment.
Loose items in the luggage compartment can shift suddenly
and cause a safety hazard or impair the handling of the
vehicle by changing the weight distribution.
– Distribute the load evenly in the luggage compartment
⇒ page 79.
– Place heavy items as far forward as possible in the
luggage compartment and secure them properly.
– Use the fastening rings* provided ⇒ page 193 or the
luggage net* for securing heavy items.
WARNING
•
Loose items in the luggage compartment can shift suddenly
and cause a safety hazard or impair the handling of the vehicle by
changing the weight distribution.
•
Always stow objects in the luggage compartment and secure
them on the fastening rings*.
•
Transporting heavy objects may affect the vehicle's handling by
shifting the centre of gravity – this could cause an accident. Take
extra care when driving and adjust your speed accordingly.
•
Never exceed the maximum axle loads or the maximum gross
weight for the vehicle ⇒ page 323, “Performance, weights and
dimensions”. Exceeding the permitted axle loads or gross weight
limit can affect the vehicle's handling characteristics, and increase
the risk of accidents, personal injuries or damage to the vehicle.
•
Never leave your vehicle unattended when the boot lid is open.
Children could climb into the boot and close the boot lid from the
document_0900452a81b1b9de.book Seite 193 Donnerstag, 26. Juli 2007 9:16 09
Safe driving
193
vehicle and the weight of the object. The most significant factor,
however, is the speed of the vehicle.
WARNING (continued)
inside. In this case the child would be unable to get out of the
vehicle without help. This could have fatal consequences.
•
Never allow children to play in or around the vehicle. Always
close and lock the boot lid and all the doors when you leave the
vehicle.
•
Never let passengers ride in the luggage compartment. All
occupants must be properly restrained by the seat belts at all
times ⇒ page 194.
An example: An object weighing 4.5 kg is lying unsecured in the
vehicle. During a frontal collision at a speed of 50 km/h, this object
generates a force corresponding to 20 times its weight. That means
that the effective weight of the object increases to about 90 kg. You
can imagine the severity of the injuries which might be sustained if
this “projectile” strikes an occupant as it flies through the
passenger compartment.
WARNING
•
Note
Air circulation in the vehicle helps reduce fogging of the
windows. Used air escapes through ventilation slots in the rear of
the vehicle. Make sure that these ventilation slots are not
obstructed.
•
Suitable belts for securing loads to the fastening rings* are
commercially available.
If items of luggage or other objects are secured to the fastening
rings with inappropriate or damaged retaining cords, injuries
could result in the event of sudden braking or a collision.
•
To prevent pieces of luggage or other objects from flying
forward, always use appropriate retaining cords which are properly secured to the fastening rings.
•
Never secure a child seat on the fastening rings.
Applies to vehicles: with fastening rings
Fastening rings
Unsecured loads are a hazard to all vehicle occupants.
There are fastening rings in the luggage compartment
which can be used to secure luggage and other objects
⇒ page 79.
– Use the fastening rings to secure items safely in the
luggage compartment ⇒
in “Loading the luggage
compartment” on page 79.
During a collision or an accident, even small and light objects can
possess so much energy that they can cause very severe injuries.
The amount of this “kinetic energy” depends on the speed of the
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 194 Donnerstag, 26. Juli 2007 9:16 09
194
Seat belts
Seat belts
Why is it so important to use seat
belts?
Seat belts provide effective protection
The common belief that passengers can brace their
weight with their hands in a minor collision is false.
the forces acting on the occupants and consequently the risk of
injury.
Although these examples are based on a frontal collision, the physical principles involved are the same in other types of accidents and
for vehicles with an airbag system. This is why it is so important to
put on the seat belts before every trip – even when “just driving
around the corner”. Ensure that your passengers wear their seat
belts as well ⇒
.
Properly worn seat belts have been shown to be an effective means
of reducing the potential for injury and improving the chances of
survival in a serious accident ⇒ page 195, “Forces acting in a collision”.
Fig. 203 Driver
protected by the properly worn seat belt
during a sudden brake
manoeuvre
It is an established fact that seat belts provide good protection in
accidents. Therefore wearing a seat belt is required by law in most
countries.
Properly worn seat belts hold the occupants in the best position for
maximum protection ⇒ fig. 203. The seat belts are capable of
absorbing much of the kinetic energy arising in a collision. Also they
help to prevent uncontrolled movements which could lead to severe
injuries ⇒ page 195, “Important safety instructions for using seat
belts”.
If they wear the seat belts correctly, the passengers benefit greatly
from the ability of the belts to reduce the kinetic energy gradually.
The front crumple zones and other passive safety features (such as
the airbag system) are also designed to absorb the kinetic energy
generated in a collision. Taken together, all these features reduce
For information on how children can travel safely in the car
⇒ page 210, “Points to remember if children are travelling in the
car”.
WARNING
•
Seat belts must be put on before every trip – even when driving
in town. This also applies to the rear passengers (injury risk).
•
During pregnancy, women should always ensure they wear a
seat belt. The best way to protect the unborn child is to protect the
mother ⇒ page 198, “Wearing and adjusting the seat belts during
pregnancy”.
document_0900452a81b1b9de.book Seite 195 Donnerstag, 26. Juli 2007 9:16 09
Seat belts
Important safety instructions for using seat
belts
There are a number of safety points concerning the seat
belts which you should remember. This will help to reduce
the risk of injury in an accident.
195
WARNING (continued)
buckle of any of the belts is damaged, the belt must be replaced
by a qualified workshop.
•
The seat belts must not be removed or modified in any way. Do
not attempt to repair a damaged belt yourself.
•
Seat belts which have been worn in an accident and stretched
must be replaced by a qualified workshop. The belt anchorages
should also be checked.
WARNING
•
The seat belts can only provide maximum protection if the
seats are adjusted properly ⇒ page 73, “Seats and storage”.
•
To ensure proper protection, it is important to wear the seat
belts in the correct position ⇒ page 197, “How to wear seat belts
properly”. Ensure that the seat belts are worn exactly as recommended in this chapter. Belts which are not worn properly can
increase the risk of injury in accidents considerably.
Forces acting in a collision
Do not allow the seat belt to become twisted or jammed, or to
rub on any sharp edges.
Very large forces are generated during a collision; these
forces have to be absorbed.
•
•
The physical principles involved in a frontal
impact
Never allow two passengers (even children) to share the same
seat belt. It is especially dangerous to place a seat belt over a child
sitting on your lap.
•
Do not wear the belt over hard or fragile objects (such as
glasses or pens, etc.) because this can cause injuries.
•
Loose, bulky clothing (such as an overcoat over a jacket)
impairs the proper fit and function of the belts.
Fig. 204 Passengers of
a vehicle which is
headed for a brick wall.
They are not using seat
belts.
•
The belts must be kept clean, otherwise the retractors may not
work properly ⇒ page 250, “Seat belts”.
•
The slot in the seat belt buckle must not be blocked with paper
or other objects, as this can prevent the latch plate from engaging
properly.
•
The latch plate of the belt must always be engaged in the
correct buckle for that seat, otherwise the belt will not be fully
effective.
•
Check the condition of the seat belts at regular intervals. If you
notice that the belt webbing, fittings, retractor mechanism or
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 196 Donnerstag, 26. Juli 2007 9:16 09
196
Seat belts
What happens to passengers not wearing
seat belts?
Passengers not wearing seat belts risk fatal injuries in the
event of an accident.
Fig. 205 The vehicle
crashes against the
wall
The physical principles involved in a frontal collision are relatively
simple:
Both the moving vehicle and the passengers possess energy, which
is known as “kinetic energy” ⇒ page 195, fig. 204. The amount of
“kinetic energy” depends on the speed of the vehicle and the weight
of the vehicle and passengers. The higher the speed and the greater
the weight, the more energy there is to be absorbed in an accident.
The most significant factor, however, is the speed of the vehicle. If
the speed doubles from 25 km/h to 50 km/h, for example, the kinetic
energy increases by a factor of four. Because these passengers are
not restrained by seat belts, the entire amount of kinetic energy has
to be absorbed at the point of impact ⇒ fig. 205. This would result
in serious or potentially fatal injury.
Even at urban speeds of 30 km/h to 50 km/h, the forces acting on the
occupants in a collision can reach the equivalent of 1 ton (1000 kg)
or more. At greater speed these forces are even higher. A rule of
thumb: if the speed doubles, the forces increase by a factor of four.
Passengers who do not wear seat belts are not “attached” to the
vehicle. In a frontal collision they will continue to move forward at
the speed their car was travelling just before the impact.
Fig. 206 A driver not
wearing a seat belt can
be thrown forwards
Fig. 207 A rear
passenger not wearing
a seat belt can be
thrown forwards
In a frontal collision, unbelted passengers will be thrown forwards
and make violent contact with the steering wheel, dashboard, windscreen, etc ⇒ fig. 206. Passengers not wearing their belts risk being
thrown out of the car, resulting in potentially fatal injuries.
The common belief that occupants can brace their weight with their
hands in a minor collision is false. Even at low speeds the forces
acting on the body in a collision are so great that it is not possible
to hold yourself in the seat.
document_0900452a81b1b9de.book Seite 197 Donnerstag, 26. Juli 2007 9:16 09
Seat belts
It is also important for the rear passengers to wear seat belts, as
they could otherwise be thrown forwards violently in an accident.
Rear passengers who do not use seat belts endanger not only themselves but also the other occupants ⇒ page 196, fig. 207.
How to wear seat belts properly
Putting on the three-point seat belts
197
– To fasten the belt, take hold of the latch plate and pull it
slowly across your chest and lap ⇒
.
– Insert the latch plate into the buckle for the appropriate
seat and push it down until it is securely locked with an
audible click ⇒ fig. 209.
– Pull the belt to check that it is now securely fastened.
The three-point inertia reel belts are tensioned automatically. The
retractor system gives complete freedom of movement, as long as
the pull on the belt is slow. Hard braking locks the belt. The belt will
also lock when you accelerate, drive up or down a steep hill or in a
sharp curve.
Always fasten your seat belts before driving off.
WARNING
•
Always make certain that the belt is positioned properly
⇒ fig. 208 – risk of injury ⇒ page 197, “Adjusting the seat belts”.
Fig. 208 Positioning of
head restraints and
seat belts
•
The latch plate of the belt must always be engaged in the
correct buckle for that seat. Otherwise the belt will not be fully
effective and the danger of injury increases.
Adjusting the seat belts
Always position seat belts properly for maximum safety.
Fig. 209 Driver's seat:
Belt buckle and latch
plate
– Adjust the front seat and head restraint correctly before
putting on the seat belt ⇒ page 73, “Seats and storage”.
Controls
Safety
Driving tips
Fig. 210 Adjusting
shoulder and lap belt
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 198 Donnerstag, 26. Juli 2007 9:16 09
198
Seat belts
The height of the front seat on your vehicle can be adjusted in order
to match the position of the seat belt to your height.
Women should always ensure they adjust the seat belt
correctly during pregnancy.
– Adjust the front seat and head restraint correctly before
putting on the seat belt ⇒ page 73, “Seats and storage”.
WARNING
•
The diagonal part of the belt should never be positioned across
the neck, but roughly over the centre of the shoulder; it should fit
closely against the upper part of the body. The lap part of the belt
must be worn tightly across the hips, and not over the abdomen
⇒ page 197, fig. 210. Pull the belt tight if necessary to take up any
slack.
•
Always make sure that belt is positioned properly. Incorrectly
worn seat belts can give rise to injuries even in a minor collision.
•
Seat belts worn too loose can result in injuries because they
allow excessive forward movement in a crash; the occupant will
be brought to a sudden stop by the belt webbing.
– To fasten the belt, take hold of the latch plate and pull it
slowly down across your chest. Wear the lap portion of
the seat belt as low as possible over the hips so that there
is no pressure on the stomach ⇒ fig. 211, ⇒
.
– Insert the latch plate into the buckle for the appropriate
seat and push it down until it is securely locked with an
audible click ⇒ page 197, fig. 209.
– Pull the belt to check that it is now securely fastened.
WARNING
Wearing and adjusting the seat belts during
pregnancy
To afford the best protection for the unborn child it is
important for the mother to wear the seat belt properly at
all times.
Fig. 211 Positioning
seat belts during pregnancy
During pregnancy, women should especially make sure to wear
the lap portion of the seat belt as low as possible across the hips
so that there is no pressure on the stomach.
document_0900452a81b1b9de.book Seite 199 Donnerstag, 26. Juli 2007 9:16 09
Seat belts
199
Taking off the seat belts
Applies to vehicles:
Seat belt height adjustment
The red button releases the belt from the buckle.
Seat belt height adjusters can be used to adjust the height
of the shoulder portion of the seat belt.
Fig. 212 Belt height
adjustment for the
front seats: guide
fitting
2 ,
– Take hold of the guide fitting and slide it up ⇒ fig. 212 A
or
– Compress the adjuster
2 .
downwards A
1 and slide the guide fitting
A
– After adjusting, pull the shoulder belt sharply to check
that the catch on the guide fitting is engaged securely.
•
Note
The shoulder portion of the seat belt must be positioned roughly
midway over the shoulder – it must never rest against the neck
⇒
in “Adjusting the seat belts” on page 197.
• It is also possible to adjust the height of the front seats to obtain
the best position for the front seat belts.
Controls
Safety
Driving tips
Fig. 213 The latch
plate of the belt
springs out of the
buckle
– Press the red button in the seat belt buckle ⇒ fig. 213.
The latch plate will spring out of the buckle.
– Guide the belt back by hand so that it is taken up by the
retractor.
Belt tensioners
How the belt tensioners work
The seat belts for the driver and front passenger are
equipped with belt tensioners.
The seat belts on the front seats are tensioned automatically in
frontal, side and rear-end impacts above a certain degree of
severity. This helps to reduce the forward motion of the occupants.
In a less severe accident, or in the event of a roll-over, the belt
tensioners are not activated.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 200 Donnerstag, 26. Juli 2007 9:16 09
200
Seat belts
WARNING
•
Any work on the tensioner system or removal and installation
of system components for other repairs must be performed by a
qualified workshop.
•
The belt tensioners can only be activated once. If they have
been activated at any time, the system must be replaced.
•
Note
Some smoke may be released when the belt tensioners are activated. This does not mean there is a fire in the vehicle.
•
The relevant safety requirements must be observed when the
vehicle or components of the system are scrapped. Your authorised
Audi dealer is familiar with these regulations and will be pleased to
pass on the information to you.
document_0900452a81b1b9de.book Seite 201 Donnerstag, 26. Juli 2007 9:16 09
Airbag system
201
Airbag system
Description of airbag system
•
General notes on airbag system
•
goes out and then comes on again after the ignition is switched
on,
The airbag is an integral part of the car's passive safety
system.
In conjunction with the three-point seat belts, the airbag system
gives the front occupants additional protection for the head and
chest in the event of a severe frontal collision.
In a severe side collision the side airbags and the head-protection
airbags reduce the risk of injury to the occupants in the areas of the
body facing the impact ⇒
.
comes on or flickers while the car is moving.
WARNING
•
The airbags are not a substitute for the seat belts; they are an
integral part of the car's overall passive safety system. The airbags
can only offer effective protection if the occupants are wearing
their seat belts. For this reason it is very important to wear the
seat belts at all times ⇒ page 194, “Why is it so important to use
seat belts?”.
•
The seat belts and airbags can only provide maximum protection if the occupants are seated correctly ⇒ page 73, “Seats and
storage”.
In addition to their normal function of protecting the occupants in a
collision, the seat belts also hold them in a position where the
airbags can inflate properly and provide maximum protection.
•
The airbag system will only work with the ignition on. The airbag
system is monitored electronically; the airbag warning lamp indicates whether the system is functioning properly.
•
The main parts of the airbag system are:
•
•
•
the electronic monitoring system (control unit and sensors),
the two front airbags,
the front side airbags, the side airbags on the outer rear seats*
and the head-protection airbags,
•
the airbag warning lamp in the instrument cluster.
does not come on when the ignition is switched on,
does not go out about 4 seconds after the ignition is switched
on,
Controls
Safety
Components of the airbag system are located in various parts
of the vehicle. If repairs to other vehicle components make it
necessary to perform work on the airbag system or to remove or
install parts of the airbag system, this may cause damage to the
airbag system. As a result, the airbags may not inflate correctly or
may not be triggered at all in an accident situation. For this reason,
you should always have the work carried out by a qualified workshop.
•
There is a fault in the airbag system if the warning
lamp
•
•
If you do not wear a seat belt, if you lean forward, or are not
seated correctly while the vehicle is in motion, you are at greater
risk of injury should the airbag system be triggered in an accident.
Driving tips
If a fault should occur in the airbag system, have the system
checked immediately by a qualified workshop. Otherwise the
system may fail to trigger in an accident.
•
Do not attempt to modify components of the airbag system in
any way.
•
Never make any alterations to the front bumper or the body.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 202 Donnerstag, 26. Juli 2007 9:16 09
202
Airbag system
WARNING (continued)
•
•
Do not remove the front seats.
The airbag system can only be activated once; if the airbag has
been triggered, the system must be replaced. Should the airbag
system or airbag modules have to be replaced, the qualified workshop carrying out the replacement will document all details in the
appropriate section of the Service Schedule.
•
If you sell the vehicle, please remember to pass on the
complete Service Wallet to the new owner. If any of the airbags
have been deactivated, it is important that the new owner is also
given the relevant documents.
•
The relevant safety requirements must be observed when the
vehicle or components of the airbag or belt tensioner systems are
scrapped.
• In an accident in which one or more airbags are triggered the
alternator and the starter are - for safety reasons - both disconnected from the battery via a pyrotechnic circuit breaker.
− Any repairs to the pyrotechnic circuit breaker must always
be performed by a qualified workshop (accident risk).
− The relevant safety requirements must be observed when
the vehicle or the circuit breaker are scrapped.
When are the airbags triggered?
The airbag system is triggered in collisions with a severe
impact.
The airbag system is designed so that the airbags for the driver and
front passenger are triggered in a severe frontal collision.
In severe side collisions the side airbags on the impact side of the
vehicle are triggered together with the head-protection airbag.
The front airbags, side airbags and one of the head-protection
airbags may be triggered together in certain types of accident.
The airbag system is not triggered in minor frontal or side collisions,
or in rear collisions or if the car overturns. In these situations the
occupants are protected by wearing the seat belts.
Factors determining the triggering response
It is not possible to define the exact triggering response of the
airbag system in all possible situations, since the circumstances in
different types of accident will vary considerably. Important factors
include, for example, the nature (hard or soft) of the object which
the car hits, the angle of impact, vehicle speed and so on.
Whether the airbags are triggered depends primarily on the vehicle
deceleration rate resulting from the collision. By processing the
signals from the sensors located in the vehicle, the electronic
control unit is immediately able to evaluate the severity of the collision and activate the restraint systems accordingly. If the deceleration rate is below the predefined reference value in the control unit
the airbags will not be triggered, even though the accident may
cause extensive damage to the car.
Note
The airbag releases a fine dust when it inflates. This is quite normal
and does not mean there is a fire in the vehicle.
document_0900452a81b1b9de.book Seite 203 Donnerstag, 26. Juli 2007 9:16 09
Airbag system
Front airbags
How the front airbags work
Description of front airbags
When fully inflated, the airbags reduce the risk of head or
chest injury.
203
The airbag system is not a substitute for the seat belts.
Fig. 216 Front airbags
in inflated condition
Fig. 214 Driver's
airbag in steering
wheel
The airbag system is designed so that the airbags for the driver and
front passenger are triggered in a severe frontal collision.
In certain types of accident the front airbags, side airbags and one
of the head-protection airbags may be triggered together.
Fig. 215 Front
passenger's airbag in
dashboard
The front airbag for the driver is located in the padded hub of the
steering wheel ⇒ fig. 214. The front airbag for the front passenger
is in the dashboard above the glove box ⇒ fig. 215. The locations of
the airbags are marked with the word “AIRBAG”.
When the system is triggered, the airbags fill with a propellant gas
and open out in front of the driver and front passenger ⇒ fig. 216.
In order to provide the desired extra protection in an accident, the
airbags have to inflate extremely rapidly (within fractions of a
second). The fully deployed airbags cushion the forwards movement of the front occupants and help to reduce the risk of injury to
the head and the upper part of the body.
Special openings in the airbag allow the gas to escape at a
controlled rate to restrain the forward movement of the occupant's
head and torso. Once the impact has been absorbed, the airbag
deflates sufficiently for the front occupants to see forward.
In conjunction with the three-point seat belts, the front airbags give
additional head and chest protection for the driver and front
passenger in the event of a severe frontal collision ⇒
in “Important safety notes on the front airbag system” on page 204.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 204 Donnerstag, 26. Juli 2007 9:16 09
204
Airbag system
Important safety notes on the front airbag
system
There are a number of safety points concerning the airbag
system which you should remember. This will help to
reduce the risk of injury in an accident.
WARNING (continued)
deactivated. However, if you have no alternative but to use a rearward-facing child seat on the front passenger's seat, the front
passenger's airbag must be deactivated beforehand by means of
the key-operated switch* ⇒ page 208. Failure to observe this
precaution could result in serious or potentially fatal injury.
•
Occupants sitting in the front of the car must never carry any
objects or pets in the space between them and the airbags, or
allow children or other passengers to travel in this position.
•
Fig. 217 Minimum
distance from steering
wheel
Do not cover or stick anything on the steering wheel hub or the
soft plastic surface of the airbag unit on the passenger's side of
the dashboard, and do not obstruct or modify them in any way.
These parts should only be cleaned with a dry cloth (or with a
cloth moistened with plain water). It is also important not to
attach any objects such as cup holders or telephone mountings to
the surfaces covering the airbag units.
•
WARNING
•
It is important for the driver and front passenger to maintain a
distance of at least 25 cm from the steering wheel or dashboard
⇒ fig. 217. The airbag system will not be able to give the required
protection if you sit too close to the steering wheel or dashboard.
There is also a risk of injury if the airbags are inflated. The front
seats and head restraints must always be positioned correctly for
the height of the occupant.
• If you do not wear a seat belt, if you lean forward or to the side,
or are not seated correctly while the vehicle is in motion, you are
at greater risk of injury. Should the airbag system be triggered in
an accident there is an even greater risk of injury.
•
Never let a child travel on the front seat without an appropriate
restraint system. If the airbag is triggered in an accident, the child
could sustain serious or fatal injuries ⇒ page 210, “Child safety”.
•
Never install a rearward-facing child safety seat on the front
passenger's seat unless the front passenger's airbag has been
Any work on the airbag system or removal and installation of
the airbag components for other repairs (such as repairs to the
steering wheel or removal of seats) must be performed by a qualified workshop.
Note
If necessary, you can deactivate the front passenger's airbag by
means of the key-operated switch* ⇒ page 208.
document_0900452a81b1b9de.book Seite 205 Donnerstag, 26. Juli 2007 9:16 09
Airbag system
Side airbags
How the side airbags work
Description of side airbags
When fully inflated, the side airbags reduce the risk of
injuries to the upper part of the body.
205
The airbag system is not a substitute for the seat belts.
Fig. 219 Side airbags
in inflated condition
Fig. 218 Location of
side airbag in driver's
seat
The side airbags are located in the backrest padding of the front
seats ⇒ fig. 218. The locations of the airbags are marked with the
word “AIRBAG”.
In conjunction with the three-point seat belts, the side airbags give
the occupants additional protection for the whole upper part of the
body (i.e. the chest, stomach and pelvis) in the event of a severe side
collision ⇒
in “Important safety notes on the side airbag system”
on page 206.
In a side collision the side airbags reduce the risk of injury to the
areas of the body facing the impact.
If the side airbags are activated, the head-protection airbags (sideguard system) are always triggered at the same time for additional
protection on the side of the vehicle facing the impact
⇒ page 207.
Controls
Safety
Driving tips
In certain types of side collisions the side airbags (front and rear*)
are triggered on the impact side of the vehicle ⇒ fig. 219.
The front airbags, side airbags and the head-protection airbag may
be triggered together in certain types of accident.
When the system is triggered, the airbag is filled with propellant
gas.
In order to provide the desired extra protection in an accident, the
airbags have to inflate extremely rapidly (within fractions of a
second). The airbag releases a fine dust when it inflates. This is quite
normal and does not mean there is a fire in the vehicle.
When fully deployed, the airbags cushion the impact for the occupants and help to reduce the risk of injury to the whole upper part
of the body (i.e. the chest, stomach and pelvis) on the side facing the
door.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 206 Donnerstag, 26. Juli 2007 9:16 09
206
Airbag system
Important safety notes on the side airbag
system
There are a number of safety points concerning the airbag
system which you should remember. This will help to
reduce the risk of injury in an accident.
WARNING
•
If you do not wear a seat belt, if you lean forward, or are not
seated correctly while the vehicle is in motion, you are at greater
risk of injury should the side airbags on the front seats or the outer
rear seats* be triggered in an accident. This applies particularly to
children if they are not properly protected by a child restraint
system ⇒ page 212, “Important notes on side airbags and child
safety”.
•
If children are not seated correctly, they are at greater risk of
injury in an accident. This is particularly the case if the child is
travelling on the front passenger's seat and the airbag system is
triggered. This could result in serious or potentially fatal injury
⇒ page 210, “Child safety”.
•
It is also important not to attach any accessories (such as cup
holders) to the doors. This would impair the protection offered by
the side airbags (front and rear*).
•
The sensors for the airbags are located in the front doors. You
must therefore not make any modifications to the doors or door
trim (e.g. retrofitting loudspeakers), as this could impair the function of the side airbags. Any damage to the front doors could lead
to faults in the system. Repairs or any other work on the front
doors must therefore always be carried out by a qualified workshop.
•
The built-in coat hooks should only be used for lightweight
clothing. Do not leave any heavy or sharp-edged objects in the
pockets.
WARNING (continued)
•
Do not apply excessive force to the sides of the backrests (such
as hard knocks or kicks), as this could damage parts of the system.
The side airbags could then fail to operate when required.
•
If you intend to fit protective covers over the seats, these must
be of the specific type approved for use on Audi seats with side
airbags. Conventional seat covers would obstruct the side airbag
when it inflates out of the backrest, and seriously reduce the
airbag's effectiveness.
•
Any damage to the original seat upholstery or around the
seams of the side airbag units must be repaired immediately by a
qualified workshop.
•
Any work involving the side airbag system or removal and
installation of the airbag components for other repairs (such as
repairs to the seats) must always be performed by a qualified
workshop. Otherwise the airbag system may fail to work
properly.
document_0900452a81b1b9de.book Seite 207 Donnerstag, 26. Juli 2007 9:16 09
Airbag system
Head-protection airbags (sideguard)
How the head-protection airbags work
Description of head-protection airbags
When fully inflated, the airbags reduce the risk of head or
chest injury in a side collision.
207
The head-protection airbags work together with the side
airbag system to give extra protection in a side impact.
Fig. 220 Location of
head-protection
airbags above the
doors
The head-protection airbags are located above the doors on the left
and right sides of the vehicle ⇒ page 207, fig. 220. The locations of
the airbags are marked with the word “AIRBAG”.
In conjunction with the three-point seat belts and side airbags, the
head-protection airbags give the occupants additional protection
against head and neck injuries in a severe side collision ⇒
in
“Important safety notes on the head-protection airbags” on
page 208.
Together with other design features (including cross-braces in the
seats and the overall strength of the body structure), the sideguard
system offers an effective further improvement to occupant protection in side impacts.
Fig. 221 Head-protection airbags in inflated
condition
In certain types of side collisions the head-protection airbag is triggered together with the side airbag on the impact side of the vehicle
⇒ fig. 221.
When the system is triggered, the airbag fills with a propellant gas
and covers the entire area in front of the side windows, including
the door pillars. In this way the system is able to protect both the
front and the rear occupants on the side of the vehicle where the
impact occurs. The head-protection airbag inflates to soften the
impact if an occupant strikes parts of the interior or objects outside
the vehicle with their head. By reducing the head impact and
restraining uncontrolled movement of the head, the airbag also
reduces the forces acting on the neck. In addition, since it covers the
front door pillar when fully inflated, the head-protection airbag also
gives extra protection if the car should collide with an obstacle at an
oblique angle.
The front airbags, side airbags and head-protection airbags may be
triggered together in certain types of accident.
In order to provide the desired extra protection in an accident, the
airbags have to inflate extremely rapidly (within fractions of a
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 208 Donnerstag, 26. Juli 2007 9:16 09
208
Airbag system
second). The airbag releases a fine dust when it inflates. This is quite
normal and does not mean there is a fire in the vehicle.
Important safety notes on the headprotection airbags
There are a number of safety points concerning the airbag
system which you should remember. This will help to
reduce the risk of injury in an accident.
WARNING
•
It is important to ensure that the area around the openings for
the head-protection airbags remains unobstructed at all times, so
that the airbags can inflate properly if needed.
•
The built-in coat hooks should only be used for lightweight
clothing. Do not leave any heavy or sharp-edged objects in the
pockets. When using the coat hooks, do not hang the clothes on
coat hangers.
•
The space between the passengers and the head-protection
airbags must never be occupied by children, other passengers or
pets. Passengers should never lean out or put a hand or arm out of
the window while the vehicle is in motion.
WARNING (continued)
•
Where sun blinds are fitted on the rear doors, these must not
obstruct or impair the airbags in any way.
•
If unsuitable accessories are installed near the head-protection
airbag, the protection afforded by the airbag can be seriously
impaired if the system is triggered. When the head-protection
airbag opens, parts of these accessories could be thrown into the
vehicle and injure passengers ⇒ page 277.
•
Any work involving the head-protection airbags, or removal
and installation of the airbag components for other repairs (such
as repairs to the roof liner), must always be performed by a qualified workshop. Otherwise the airbag system may fail to work
properly.
Applies to vehicles: with key-operated switch for front passenger's airbag
Deactivating the front passenger's
airbag via the key-operated switch
If an airbag has been deactivated, it should be reactivated
as soon as possible so that it can continue to give the
required protection.
•
Do not move the sun visors out to cover the side windows if
there is anything attached to them (such as pens or a remote
control for the garage door). These objects could cause injury if the
head-protection airbag is triggered.
•
The sensors for the airbags are located in the front doors. You
must therefore not make any modifications to the doors or door
trim (e.g. retrofitting loudspeakers), as this could impair the function of the side airbags. Any damage to the front doors could lead
to faults in the system. Repairs or any other work on the front
doors must therefore always be carried out by a qualified workshop.
Fig. 222 Key-operated
switch in glove box for
deactivating front
passenger's airbag
document_0900452a81b1b9de.book Seite 209 Donnerstag, 26. Juli 2007 9:16 09
Airbag system
209
When the front passenger's airbag is deactivated using the keyoperated switch, the seat belt warning lamp for the front passenger
 ⇒ page 18 is also switched off.
WARNING
Fig. 223 Lamp indicates that front
passenger's airbag has
been deactivated via
key-operated switch
The key-operated switch for deactivating the front
passenger's airbag is located in the glove box ⇒ fig. 222.
– To deactivate the front passenger's airbag, insert the
OFF .
ignition key into the switch and turn it to position A
– The front passenger's airbag can be reactivated by
ON .
turning the key to position A
Deactivating front passenger's airbag when a child
safety seat is in use
If you have no alternative but to install a rearward-facing child safety
seat on the front passenger's seat you must deactivate the front
passenger's airbag beforehand.
•
If you have no alternative but to install a rearward-facing child
seat on the front passenger's seat, the front passenger's airbag
must be deactivated beforehand. Potentially fatal injuries to the
child can result if the front passenger's airbag is not deactivated!
⇒ page 211, “Using a child safety seat on the front passenger's
seat”
•
If you have deactivated the front passenger's airbag, reactivate
it as soon as the child seat is no longer needed so that the airbag
can continue to give the required protection.
•
It is the driver's responsibility to ensure that the key-operated
switch is set to the correct position.
Note
All the other airbags in the car will remain functional if the front
passenger's airbag has been deactivated with the key-operated
switch.
We recommend, however, that child seats should be only fitted on
the rear seat so that the front passenger's airbag can remain functional and provide protection in an accident ⇒ page 210.
Monitoring of airbag system
The airbag warning lamp will light up for a few seconds every time
the ignition is switched on.
If the front passenger's airbag has been deactivated via the keyoperated switch, the indicator lamp “PASSENGER AIRBAG OFF” will
light up constantly as a reminder ⇒ page 209, fig. 223. Please refer
also to the description of the  warning lamp in the instrument
cluster ⇒ page 17.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 210 Donnerstag, 26. Juli 2007 9:16 09
210
Child safety
Child safety
Points to remember if children are
travelling in the car
Introduction
Statistics show that children are generally safer on the
rear seat than on the front passenger's seat.
Children under 12 years of age should normally travel on the rear
seat 2) . Children travelling on the rear seat must use a child restraint
system or the seat belts provided, depending on their age, height
and weight. For safety reasons, the child restraint system should be
installed behind the front passenger's seat.
The physical principles involved and the forces acting in a collision
apply to children just as much as adults ⇒ page 195, “Forces acting
in a collision”. But, unlike adults, children do not have fully developed muscle and bone structures. This means that children are
subject to a greater risk of injury.
To reduce this risk, children must always use special child restraint
systems when travelling in the car.
Use only child restraint systems which are officially approved under
the European standard ECE R 44 and are suitable for the child. ECE R
refers to the Economic Commission of Europe Recommendation,
which categorises child restraint systems in 5 groups ⇒ page 213,
“Child seat categories”. Child restraints that have been tested and
approved under the ECE R 44 standard bear the ECE-R 44 test mark
on the seat (the letter E in a circle with the test number below it).
We recommend using child restraint systems from the range of
Audi Genuine Accessories available from Audi dealers. The
“Huckepack” range includes suitable restraint systems for all ages.
2)
Observe any restrictions or regulations to the contrary.
These systems have been specially developed and tested for use in
Audi vehicles and comply with the ECE-R 44 standard.
Follow the manufacturer's instructions and observe any statutory
requirements when installing and using child restraints ⇒
in
“Important safety notes for using child safety seats”.
Important safety notes for using child safety
seats
Correct use of child safety seats can help to reduce the
risk of injury in an accident.
WARNING
•
All vehicle occupants, especially children, must wear a seat
belt while the vehicle is in motion.
•
Children who are less than 1.5 metres tall must not wear a
normal seat belt without a child restraint, as this could cause injuries to the abdominal and neck areas.
•
Babies and children must never travel on another occupant's
lap.
•
A suitable child safety seat can protect your child ⇒ page 213,
“Child safety seats”.
•
•
•
Never allow two children to occupy one child safety seat.
Never leave a child without supervision in a child safety seat.
Never allow a child to travel in the car without a suitable child
restraint.
•
Never allow a child to stand up or kneel on a seat while the car
is moving. In an accident, the child could be catapulted through
the car, causing possibly fatal injuries to itself and other occupants.
document_0900452a81b1b9de.book Seite 211 Donnerstag, 26. Juli 2007 9:16 09
Child safety
WARNING (continued)
211
WARNING
•
If children lean forward or are otherwise out of position when
the car is moving, they are at greater risk of injury in an accident.
This is particularly the case if the child is travelling on the front
passenger's seat and the airbag system is triggered in an accident.
There is then a risk of serious or potentially fatal injury.
•
•
To ensure proper protection, it is important to wear the seat
belts in the correct position ⇒ page 197, “How to wear seat belts
properly”. Always check that the belt is properly positioned
according to the instructions provided by the manufacturer of the
child safety seat. Incorrectly worn seat belts can give rise to injuries even in a minor collision.
•
•
Never install a rearward-facing child safety seat on the front
passenger's seat if the front passenger's airbag has not been deactivated ⇒ page 211.
•
Extra caution is advised if you are installing a child safety seat
using the same mounting bolts as the existing car seat belts. The
bolts must be screwed in all the way to the full depth of the
mounting holes and tightened to a torque of 50 Nm. Failure to
observe this precaution could result in potentially fatal injury. We
recommend having the installation performed by a qualified
workshop.
Do not use a rearward-facing child safety seat on the front
passenger's seat unless the front passenger's airbag has been
deactivated. The child seat would be directly in the path of the
airbag as it inflates, and the child could sustain serious or fatal
injuries if the airbag were to be deployed.
However, if you have no alternative but to use a rearwardfacing child seat on the front passenger's seat, the front
passenger's airbag must be deactivated beforehand by means of
the key-operated switch* ⇒ page 208. Failure to observe this
precaution could result in serious or potentially fatal injury.
•
Make sure that the front passenger's airbag is reactivated by
means of the key-operated switch* as soon as the child seat is no
longer needed on the front passenger's seat.
•
When using a child safety seat of the type which faces in the
direction of travel, the front passenger's seat must be moved back
to the rearmost position.
Using a child safety seat on the front
passenger's seat
Whenever possible, child safety seats should always be
installed on the rear seat.
For safety reasons, we recommend that child safety seats should be
installed on the rear seats whenever possible. However, if you have
to use a child seat on the front passenger's seat when there is no
other alternative, it is most important to note the following warnings:
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 212 Donnerstag, 26. Juli 2007 9:16 09
212
Child safety
Applies to vehicles: with side airbags
Important notes on side airbags and child
safety
Children must never sit too close to the opening for the
side airbag.
This applies particularly to children if they are travelling in a way
which does not comply with the statutory safety regulations.
Incorrect position – danger of injury from the side
airbag
If the side airbag were to inflate in an accident, it would strike the
child on the head and most likely cause serious injury ⇒ fig. 224.
Correct position – properly restrained in a suitable
child safety seat
The child is correctly seated in a suitable child restraint system on
the rear seat ⇒ fig. 225. There is enough space between the child
and the opening for the side airbag.
Fig. 224 Not properly
restrained, and too
close to the opening
for the side airbag
In an accident, the airbag would be able to inflate completely to
offer maximum protection.
WARNING
To help prevent serious injury, children travelling in the vehicle
must always be protected with a restraint system which is suited
to their age, height and weight.
•
The child's head must always be well away from the opening
for the side airbag. There is a risk of suffering injury.
•
Fig. 225 Correctly
seated in a suitable
child safety seat
The side airbags offer increased protection in a side-on collision.
In order to be effective, the side airbags need to inflate very quickly
(within fractions of a second) ⇒ page 205, “How the side airbags
work”.
The airbag inflates with such force that injury can be caused if the
occupant is not sitting upright, or if there are any objects close to
the opening for the side airbag.
Do not leave or place any objects in the space next to the side
airbag. There is a risk of suffering injury.
Note
If required, you can have the side airbags for the rear passengers
deactivated by a qualified workshop.
document_0900452a81b1b9de.book Seite 213 Donnerstag, 26. Juli 2007 9:16 09
Child safety
Child safety seats
Child safety seat: category 0 / 0+
Child seat categories
A suitable child safety seat and a correctly worn seat belt
can protect your child.
213
Only use child restraint systems that are officially
approved and suitable for the child.
Child restraint systems are covered by the European standard
ECE R 44 (issued by the Economic Commission of Europe).
The child seats are divided into 5 categories:
Category
Weight
0
0 -10 kg
⇒ page 213
0+
up to 13 kg
⇒ page 213
1
9 - 18 kg
⇒ page 214
2
15 - 25 kg
⇒ page 214
3
22 - 36 kg
⇒ page 214
Children who are taller than 1.5 metres can use the existing seat
belts without a booster cushion.
Child restraints that have been tested and approved under the ECE
R 44 standard bear the ECE-R 44 test mark on the seat (the letter E
in a circle with the test number below it).
Controls
Safety
Driving tips
Fig. 226 Child safety
seat: Category 0 / 0+
Babies up to about 9 months old / 10 kg and infants up to about
18 months old / 13 kg are best protected by child safety seats that
can be adjusted to a horizontal position ⇒ fig. 226.
Follow the manufacturer's instructions and observe any statutory
requirements when installing and using child restraints
⇒ page 210, “Important safety notes for using child safety seats”.
WARNING
Never install a rearward-facing child safety seat on the front
passenger's seat if the front passenger's airbag has not been deactivated ⇒ page 211. This can result in serious or possibly fatal
injury.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 214 Donnerstag, 26. Juli 2007 9:16 09
214
Child safety
Child safety seats: category 1
Child safety seats: category 2/3
A suitable child safety seat and a correctly worn seat belt
can protect your child.
A suitable child safety seat and a correctly worn seat belt
can protect your child.
Fig. 227 A category 1
forward-facing child
seat fitted on the rear
seat
Fig. 228 A category
2/3 forward-facing
child seat (with backrest) fitted on the rear
seat
Babies and small children up to about 4 years of age weighing
between 9 and 18 kg are best protected by child safety seats of the
type where the child faces the front of the vehicle ⇒ fig. 227.
Follow the manufacturer's instructions and observe any statutory
requirements when installing and using child restraints
⇒ page 210, “Important safety notes for using child safety seats”.
WARNING
Never install a rearward-facing child safety seat on the front
passenger's seat if the front passenger's airbag has not been deactivated ⇒ page 211. This can result in serious or possibly fatal
injury.
Fig. 229 A category
2/3 forward-facing
child seat (without
backrest) fitted on the
rear seat
Children up to about 12 years of age weighing between 15 and 36 kg
but less than 1.5 metres tall are best protected by a child safety seat
in conjunction with the three-point seat belts ⇒ fig. 228 and
⇒ fig. 229.
Follow the manufacturer's instructions and observe any statutory
requirements when installing and using child restraints
⇒ page 210, “Important safety notes for using child safety seats”.
document_0900452a81b1b9de.book Seite 215 Donnerstag, 26. Juli 2007 9:16 09
Child safety
215
WARNING
The diagonal part of the belt should be positioned roughly over the
centre of the shoulder and fit closely against the upper part of the
body. It must never be allowed to run across the neck. The lap part
of the belt should fit closely over the hips. It must not be positioned over the stomach. Pull the belt tight if necessary to take up
any slack.
Note
We recommend that you fit child safety seats with backrests.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 216 Donnerstag, 26. Juli 2007 9:16 09
216
Child safety
Fitting child safety seats
General information
Label on a child safety seat ⇒ fig. 230
1 Approval number
A
2 Manufacturer's serial number.
A
The label also shows information on the use and weight class of the
child seat.
Fig. 230 Example of an
approval number on a
child safety seat
List of recommended child restraint systems
Weight class
1)
Identification
“Huckepack”
Audi Genuine
accessories
catalogue number
Manufacturer
Model
Approval number
0+
(up to 13 kg)
G0 Plus
00A.019.900.A
Britax Römer
Baby Safe Plus
E1 03301146
1
(9 to 18 kg)
G1 ISOFIX Duo Plus
00A.019.909.B
Britax Römer
Duo Plus
E1 03301133
2
(15 to 25 kg)
1)
1)
1)
1)
1)
3
(22 to 36 kg)
1)
1)
1)
1)
1)
Under development.
For the current range of child seats from Audi Genuine Accessories
visit: http://www.audi.com
document_0900452a81b1b9de.book Seite 217 Donnerstag, 26. Juli 2007 9:16 09
Child safety
217
Extended list of recommended child restraint systems
Weight class
Identification
Catalogue number Manufacturer
Model /
Mode of securing seat
Approval number
0-1
(up to 18 kg)
ISOFIX RWF
4590.xx, 4710.xx 1)
FAIR
FAIR G0/ 1
rearward-facing with vehicle-specific platform type A
(RWF)
E4 04443513
1
(9 to 18 kg)
ISOFIX FWF
4590.xx, 4610.xx 1)
FAIR
FAIR G0/ 1
forward-facing with vehiclespecific platform type A
(FWF)
E4 04443513
Universal
4590.xx 1)
FAIR
FAIR G0/ 1
standard three-point seat
E4 03443416
belt 2)
1)manufacturer
details:
Company: FAIR srl
Address: Strada della Cisa 249/251, I- 42040 Sorbolo Levante di Brescello (RE) / Italy.
http://www.fairbimbofix.com
2)
may also be secured with two-point seat belt.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 218 Donnerstag, 26. Juli 2007 9:16 09
218
Child safety
Possible alternatives for securing a child
safety seat
A child safety seat can be secured on the rear seats and
on the front passenger's seat.
The following alternatives are available for safely securing a child
safety seat on the rear seats and on the front passenger's seat.
•
Child safety seats of the categories 0 to 3 can be secured with the
standard three-point seat belts.
•
Child safety seats of the categories 0, 0+ and 1 with the “ISOFIX”
system can be secured without seat belts using the “ISOFIX”
retainers* ⇒ page 218.
Compatibility of vehicle seat positions for child safety seats
(according to EC directive 77/541):
Weight class
Front passenger's seat
Rear seats
0, 0+
u, a, b, c
u, d
1
u, a, b, c
u, d
2
u, a
u
3
u, a
u
WARNING
While the vehicle is moving, children must always be protected
with a restraint system which is suited to their age, height and
weight. Please refer to the chapter “Child seat categories”.
•
Never install a rearward-facing child safety seat on the front
passenger's seat unless the front passenger's airbag has been
deactivated. This could result in potentially fatal injuries. If you
have no alternative but to let a child travel on the front passenger's
seat, the front passenger's airbag must be deactivated beforehand. Please refer to the chapter “Deactivating airbags”.
•
Note the important information and warnings concerning the
use of child safety seats found in the chapter “Important safety
notes when using child safety seats” and in the installation
instructions provided by the manufacturer of the child safety
seat.
Applies to vehicles: with ISOFIX system
“ISOFIX” child seat mounting system
Child safety seats with the “ISOFIX” system can be
secured quickly and easily.
u “universally compatible”
A
a The front passenger's backrest must be set as far forward as
A
possible or adapted to the child safety seat as required, and the
seat height must be adjusted to its highest position.
b The front passenger's airbag must be deactivated if a rearwardA
facing child seat is used.
c The front passenger's seat can be equipped with optional
A
“ISOFIX” retainers.
d The rear seats can be equipped with optional “ISOFIX” retainers.
A
Fig. 231 The ISOFIX
child safety seat is
pushed into the protective sleeves.
When removing or fitting the child safety seat, please be
sure to follow the manufacturer's instructions.
document_0900452a81b1b9de.book Seite 219 Donnerstag, 26. Juli 2007 9:16 09
Child safety
219
A onto the retainers A
B
– Fit the protective sleeves A
between the backrest and the seat cushion ⇒ page 218,
fig. 231.
– Push the mountings on the child safety seat into the
protective sleeves until they engage audibly (2x)
⇒ page 218, fig. 231.
– Pull on the child safety seat to check whether both
catches have engaged properly.
Child safety seats with the “ISOFIX” system can be secured quickly
and safely on the rear seat* or on the front passenger's seat*.
Detailed fitting instructions are supplied with the child safety seat.
Child seats with “ISOFIX” mountings are available from Audi dealers
and specialist retailers.
If required, the “ISOFIX” mounting system can be retrofitted.
WARNING
The retainers used here are specially designed for child safety
seats with “ISOFIX” mountings. Do not attempt to secure other
types of child safety seat, seat belts or other objects with these
retainers – this could result in serious or possibly fatal injury.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 220 Donnerstag, 26. Juli 2007 9:16 09
220
document_0900452a81b1b9de.book Seite 221 Donnerstag, 26. Juli 2007 9:16 09
Driving tips
221
document_0900452a81b1b9de.book Seite 222 Donnerstag, 26. Juli 2007 9:16 09
222
Intelligent technology
Intelligent technology
Electronic stabilisation program (ESP)
Electronic differential lock (EDL)
Description
When the EDL detects wheelspin, it brakes the spinning wheel and
directs the power to the other driven wheel (or wheels on quattro*
versions). This function is active up to about 100 km/h.
ESP increases the car's stability. It reduces the tendency to skid and
improves the stability and roadholding of the vehicle. ESP detects
critical handling situations, such as understeer, oversteer and
wheelspin on the driven wheels. It stabilises the vehicle by braking
individual wheels or by reducing the engine torque. The warning
lamp  in the instrument cluster starts flashing as soon as the ESP
intervenes.
The ESP incorporates the functions of the anti-lock brake system
(ABS), the traction control system (ASR), the electronic differential
lock (EDL) and the dynamic steering*.
Anti-lock brake system (ABS)
ABS prevents the wheels from locking up under braking until the
vehicle has reached a virtual standstill. You can continue to steer the
vehicle even when the brakes are on full. Keep your foot on the brake
pedal and do not pump the brakes. You will feel the brake pedal
pulsate while the anti-lock brake system is working.
Brake assist system
The brake assist system can speed up the braking process and
shorten the braking distance. It automatically boosts the braking
force if you press the brake pedal quickly in an emergency. On vehicles with adaptive cruise control*, the brake assist system will build
up a small amount of pressure in the hydraulic brake system if it
senses that you are too close to the vehicle in front.
Traction control system (ASR)
In the event of wheelspin, the traction control system reduces the
engine torque to match the amount of grip available. This helps the
car to start moving, accelerate or climb a gradient.
To prevent the disc brake of the braked wheel from overheating, the
EDL cuts out automatically if subjected to excessive loads. The
vehicle can still be driven. The EDL will switch on again automatically when the brake has cooled down.
Dynamic steering*
On vehicles with dynamic steering*, the ESP can also intervene in
the steering to stabilise the vehicle in critical situations.
WARNING
•
The grip provided by the ESP, ABS, ASR, EDL and dynamic
steering* systems is still subject to the physical limits of adhesion.
Always bear this in mind, especially on wet or slippery roads. If
you notice the systems cutting in, you should reduce your speed
immediately to suit the road and traffic conditions. Do not let the
extra safety provided tempt you into taking any risks when driving
– this can cause accidents.
•
Please remember that the accident risk always increases if you
drive fast, especially in corners or on a slippery road, or if you
follow too close behind the vehicle in front of you. Please bear in
mind that even ESP, ABS, brake assist, EDL, ASR and dynamic
steering* cannot compensate for the increased accident risk.
•
When accelerating on a uniformly slippery surface (for instance
all four wheels on ice or snow), press the accelerator gradually and
carefully. The driven wheels may otherwise start to spin (in spite
of the integrated control systems), which would impair the car's
stability and could lead to an accident.
document_0900452a81b1b9de.book Seite 223 Donnerstag, 26. Juli 2007 9:16 09
Intelligent technology
•
223
Note
To ensure that the ASR works properly, all four wheels must be
fitted with identical tyres. Any differences in the rolling radius of the
tyres can cause the system to reduce engine power when this is not
desired.
•
Should a malfunction occur in the ABS or EDL, both the ABS
warning lamp  and the ESP warning lamp  ⇒ page 19 will light
up.
Fig. 233 Version B:
Centre console (top),
ESP OFF button
•
In the event of a malfunction in the ESP system, the warning
lamp  ⇒ page 17 will light up.
•
If a malfunction should occur in the ABS, the ESP, EDL and ASR
will also be out of action.
•
The systems can make noises when they intervene.
Switching on and off
The ESP is switched on automatically when the engine is
started.
Switching off the traction control system (ASR)
In particular circumstances, it may be advisable to switch off the
traction control system (ASR) to allow a certain amount of wheel
slip. For example:
•
•
•
Rocking the car backwards and forwards to free it
Driving in deep snow or on loose surfaces
Driving with snow chains
Press the ESP OFF button briefly ⇒ fig. 232 or ⇒ fig. 233. The
warning lamp  will light up and the message ASR off will appear
in the driver information system display.
The traction control system (ASR) can only be switched off at speeds
below 50 km/h on vehicles with front-wheel drive. At 70 km/h it will
switch on again automatically. The ASR can be deactivated at any
speed on vehicles with four-wheel drive.
Fig. 232 Version A:
Centre console
(bottom), ESP OFF
button
Switching off the ESP
Press the ESP OFF button for longer than 3 seconds. The ESP
warning lamp  will light up and the message ESP switched off will
appear in the display. The ASR is also deactivated when the ESP is
switched off.
Switching on
Press the ESP OFF button again. The message ESP/ASR on will
appear briefly on the display.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 224 Donnerstag, 26. Juli 2007 9:16 09
224
Intelligent technology
WARNING
You should switch off the ESP only if your driving ability and traffic
conditions allow you to do so safely. Please note that, when the
ASR and ESP are switched off, the driven wheels may start to spin,
causing the vehicle to lose grip, in particular on slippery or wet
roads - danger of skidding!
Note
In certain conditions, such as in heavy rain, or after washing the car
or driving through water, the full braking effect can be delayed by
moisture (or in winter by ice) on the discs and brake pads. The
brakes should be “dried” by pressing the pedal to restore full
braking effect.
The effectiveness of the brakes can also be temporarily reduced if
the car is driven for some distance without using the brakes when
there is a lot of salt on the road in winter. The layer of salt that accumulates on the discs and pads can be removed with a few cautious
brake applications.
The ASR and ESP cannot be switched off when the adaptive cruise
control (ACC)* is on.
Corrosion
Brakes
There may be a tendency for dirt to build up on the brake pads and
corrosion to form on the discs if the car is used infrequently, or if
you only drive low mileages without using the brakes very much.
New brake pads
New brake pads do not give full braking effect for the first 400 km,
they must first be “bedded in”. However, you can compensate for
the slightly reduced braking effect by applying more pressure on
the brake pedal. Avoid placing a heavy load on the brakes during the
running-in period.
Wear
The rate of wear on the brake pads depends a great deal on how you
drive and the conditions in which the vehicle is operated. Negative
factors are, for instance, city traffic, frequent short trips or hard
driving with abrupt starts and stops.
If the brakes are not used frequently, or if corrosion has formed on
the discs, it is advisable to clean off the pads and discs by braking
firmly a few times from a moderately high speed ⇒
.
Faults in the brake system
If the brake pedal travel should ever increase suddenly, this may
mean that one of the two brake circuits has failed. Drive immediately to the nearest qualified workshop and have the fault rectified.
On the way to the dealer, be prepared to use more pressure on the
brake pedal and allow for longer stopping distances.
Low brake fluid level
Malfunctions can occur in the brake system if the brake fluid level is
too low. The brake fluid level is monitored electronically.
Wet roads; road salt
When you are driving at a speed higher than 80 km/h and have the
windscreen wipers switched on the brake pads are very briefly
brought into contact with the brake discs. This automatic process
which goes unnoticed by the driver is carried out at regular intervals
and is intended to improve braking response in wet conditions.
Brake servo
The brake servo amplifies the pressure you apply to the brake pedal.
It only works when the engine is running.
document_0900452a81b1b9de.book Seite 225 Donnerstag, 26. Juli 2007 9:16 09
Intelligent technology
WARNING
•
When applying the brakes to clean off deposits on the pads and
discs, select a clear, dry road. Be sure not to inconvenience or
endanger other road users; do not risk an accident.
•
Never let the car coast with the engine switched off (this can
cause accidents).
225
If a fault should occur in the servotronic system the power steering
will still operate. The degree of power assistance will, however, no
longer adapt to different speeds. If the electronic regulating system
is not working properly, this is most noticeable when turning the
steering wheel at low speeds (for instance when parking) – more
effort will be required than usual. The fault should be corrected by
a qualified workshop as soon as possible.
The power steering does not function when the engine is switched
off. In this case the steering wheel is very hard to turn.
•
Caution
Never let the brakes “drag” by leaving your foot on the pedal
when you do not really intend to brake. This overheats the brakes,
resulting in longer stopping distances and greater wear.
•
Before driving down a long, steep gradient, it is advisable to
reduce speed and move the selector lever to a lower gear. In this
way you will make use of the engine braking effect and relieve the
load on the brakes. If you still have to use the brakes, it is better to
brake firmly at intervals than to apply the brakes continuously.
•
If the steering is held at its turning limit when the car is stationary,
this will place an excessive load on the power steering system. In
this case, the power steering system will make noises. It will also
reduce the idling speed of the engine.
Caution
Do not keep the steering in the full-lock position for longer than
15 seconds when the engine is running – this could cause damage
to the power steering system.
Note
If the brake servo is out of action due to a malfunction, or if the
car has to be towed, you will have to press the brake pedal considerably harder to make up for the lack of servo assistance.
•
If you wish to equip the car with accessories such as a front
spoiler or wheel covers, it is important that the flow of air to the
front wheels is not obstructed, otherwise the brakes can overheat.
•
Note
If the power steering should fail at any time or the engine is
switched off (for instance when being towed), the car can still be
steered. However, more effort will be required to turn the steering
wheel.
•
If the system is leaking or malfunctioning, please take the car to
a qualified workshop as soon as possible.
•
Power steering (servotronic)
The power steering assists the driver when turning the
steering wheel (with the engine running).
The power steering requires a special hydraulic fluid. The fluid
reservoir is located at the front of the engine compartment on the
left ⇒ page 256. The correct fluid level in the reservoir is important
for the power steering to function properly. The hydraulic fluid level
is checked at the Inspection Service.
The power steering assists the driver by reducing the force needed
to turn the steering wheel. The degree of power assistance is
adapted electronically, depending on the speed.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 226 Donnerstag, 26. Juli 2007 9:16 09
226
Intelligent technology
Applies to vehicles: with four-wheel drive
Four-wheel drive (quattro®)
On quattro models the engine power is distributed to all
four wheels
Off-roader?
Your Audi does not have enough ground clearance to be used as an
off-road vehicle. It is therefore best to avoid rough tracks and
uneven terrain as much as possible.
General notes
WARNING
On four-wheel drive vehicles, the engine power is distributed to all
four wheels. The distribution of power is controlled automatically
according to your driving style and the road conditions. Also refer
to ⇒ page 222, “Description”.
•
The four-wheel drive is specially designed to complement the superior engine power of your Audi. This combination gives the car
exceptional handling and performance capabilities – both on
normal roads and in more difficult conditions, such as snow and ice.
Even so (or perhaps especially for this reason), it is important to
observe certain safety points ⇒
.
•
Winter tyres
Thanks to its four-wheel drive, your car will have plenty of traction
in winter conditions, even with the standard tyres. Nevertheless, we
still recommend that winter tyres or all-season tyres should be fitted
on all four wheels when winter road conditions are expected, mainly
because this will give a better braking response.
Even with four-wheel drive, you should always adjust your
speed to suit the conditions. Do not let the extra safety provided
tempt you into taking any risks when driving – this can cause accidents.
The braking ability of your car is limited by the grip of the tyres.
In this respect, your car is no different from a car without fourwheel drive. So do not be tempted to drive too fast on icy or slippery roads just because the car still has good acceleration in these
conditions (accident risk).
•
On wet roads bear in mind that the front wheels may start to
“aquaplane” and lose contact with the road if the car is driven too
fast. If this should happen, there will be no sudden increase in
engine speed to warn the driver, as with a front-wheel drive car. So
do not drive too fast in the wet: adjust your speed to suit the
conditions (accident risk).
Snow chains
Power management
On roads where snow chains are mandatory, this also applies to cars
with four-wheel drive ⇒ page 273, “Snow chains”.
This system helps to ensure reliable starting
Replacing tyres
On vehicles with four-wheel drive, all four tyres must have the same
rolling circumference. Also avoid using tyres with varying tread
depths ⇒ page 270, “Replacing wheels and tyres”.
The power management controls the distribution of electrical energy and thus helps to ensure that there is always
enough power available to start the engine.
If a vehicle with a conventional electrical system is left parked for a
long time, the battery will gradually lose its charge because certain
electrical equipment (such as the immobiliser) continues to draw
document_0900452a81b1b9de.book Seite 227 Donnerstag, 26. Juli 2007 9:16 09
Intelligent technology
current even when the ignition is off. In some cases there may not
be enough power available to start the engine.
Your vehicle is equipped with an intelligent power management
system to control the distribution of electrical energy. This significantly improves reliability when starting the engine, and also
prolongs the life of the battery.
The main functions incorporated in the power management system
are battery diagnosis, residual current management and dynamic
power management.
Note
The power management system is not able to overcome the
given physical limits. Please remember that the power and life of
the battery are limited.
•
A warning message will appear ⇒ page 228, “Driver message in
the instrument cluster display” if the battery power has dropped to
a level where reliable starting is impaired.
Points to remember
Battery diagnosis
The battery diagnosis function constantly registers the condition of
the battery. Sensors detect the battery voltage, battery current and
battery temperature. This enables the system to calculate the
current power level and charge condition of the battery.
Residual current management
The residual current management reduces power consumption
while the vehicle is parked. It controls the supply of power to the
various electrical components while the ignition is switched off. The
system takes the battery diagnosis data into consideration.
Depending on the power level of the battery, the individual electrical
components are switched off one after the other to prevent the
battery from losing too much charge and to ensure that the engine
can be started reliably.
Dynamic power management
While the vehicle is moving, this function distributes the available
power to the various electrical components and systems according
to their requirements. The power management ensures that onboard systems do not consume more electrical power than the
alternator can supply, and thus maintains the maximum possible
battery power level.
Controls
•
227
Safety
Driving tips
Starting ability has first priority.
Short trips, city traffic and low temperatures all place a heavy load
on the battery. In these conditions a large amount of power is
consumed, but only a small amount is supplied. The situation is also
critical if electrical equipment is in use when the engine is not
running. In this case power is consumed when none is being generated.
In these situations you will be aware that the power management
system is intervening to control the distribution of electrical power.
When the vehicle is parked for long periods
If you do not drive your vehicle for a period of several days or weeks,
the power management will gradually shut off the on-board
systems one by one, or reduce the amount of current they are using.
This limits the amount of power consumed and helps to ensure reliable starting even after a long period.
Please note that certain convenience features, such as the Audi
advanced key*, the remote control key or the electrical seat adjustment may not be available when you unlock the vehicle. These functions will be restored when you switch on the ignition and start the
engine.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 228 Donnerstag, 26. Juli 2007 9:16 09
228
Intelligent technology
With the engine switched off
If you listen to the radio or use the other MMI functions when the
engine is not running, this will discharge the battery.
The MMI display will show this warning message before the battery
power drops to a level where the starting ability is impaired.
Please start engine, otherwise system will switch off
in 3 minutes.
Driver message in the instrument cluster
display
If battery power drops to a level at which you may encounter problems when starting the engine, the following message will appear
in the instrument cluster display:
 Low battery charge: Battery will be charged while driving
This message warns you that the system you are using will be
switched off automatically after 3 minutes. You should therefore
start the engine if you wish to continue using the system.
This message reminds you that the starting reliability may be
impaired. The message will disappear as soon as you set off and the
battery is charged.
When the engine is running
Message comes on and goes out again
Although the alternator generates electrical power, the battery can
still become discharged while the vehicle is being driven. This can
occur when a lot of power is being consumed but only a small
amount supplied, especially if the battery is not fully charged
initially.
If the message appears in the display after the ignition is switched
on or while driving, and goes out again after a period of time, the
battery has been charged up again sufficiently while the vehicle was
being driven.
To restore the necessary energy balance, the system will then
temporarily shut off the electrical components that are using a lot
of power, or reduce the current they are consuming. Heating
systems in particular use a large amount of electrical power. If you
notice, for instance, that the seat heating* or the rear window
heater is not working, they may have been temporarily switched off
or regulated to a lower heat output. These systems will be available
again as soon as sufficient electrical power is available.
If the message appears in the display after the ignition is switched
on or while driving, and does not go out again, the battery is not
being maintained at the proper power level. Starting reliability may
be impaired. You should have the battery checked by a qualified
workshop as soon as possible.
You may also notice that the engine runs at a slightly faster idling
speed. This is quite normal, and no cause for concern. The increased
idling speed allows the alternator to meet the greater power
requirement and charge the battery at the same time.
Message comes on and does not go out
document_0900452a81b1b9de.book Seite 229 Donnerstag, 26. Juli 2007 9:16 09
Your vehicle and the environment
229
Your vehicle and the environment
Running in
Diesel particulate filter
A new vehicle should be run in over a distance of 1,500 km. For the
first 1,000 km the engine speed should not exceed 2/3 of the
maximum permissible engine speed – do not use full throttle and do
not tow a trailer or caravan. From 1,000 to 1,500 km you can gradually increase the engine rpm and road speed.
Applies to vehicles with diesel engine: The diesel particulate filter
can filter out almost all soot particles contained in the exhaust gas.
In normal driving conditions the filter is self-cleaning. Should the
self-cleaning function of the filter not be able to operate, e.g. when
the vehicle is continuously used only for short trips, the filter
becomes obstructed with soot and the symbol  for the diesel
particulate filter lights up ⇒ page 38.
During its first few hours of running, the internal friction in the
engine is greater than later on when all the moving parts have
bedded down.
How the vehicle is driven for the first 1,500 km also influences the
engine quality. After the first 1,500 km you should continue driving
at moderate engine speeds, in particular when the engine is cold.
This helps to reduce wear and tear on the engine and increases the
potential mileage which can be covered by the engine.
You should also avoid driving with the engine speed too low.
Change down to a lower gear when the engine no longer runs
“smoothly”. Excessively high engine speeds are prevented by an
automatic rev limiter.
Catalytic converter
Applies to vehicles with petrol engine: The vehicle must only be
used with unleaded petrol, otherwise the catalytic converter will be
destroyed.
Never run the tank completely dry. The irregular fuel supply can
cause misfiring, which would allow unburnt fuel to enter the
exhaust system, which could cause overheating and damage the
catalytic converter.
Safety
Because of the high temperatures which can occur in the emission control system (catalytic converter or diesel particulate
filter), do not park the vehicle where the exhaust can come into
contact with flammable materials under the car (e.g. on grass or
at the forest edge). - Fire hazard!
•
Do not apply any underseal agents in the area around the
exhaust system - fire hazard!
How to improve economy and
minimise pollution
Emission control systems
Controls
WARNING
•
Driving tips
Fuel economy, environmental impact and wear on the engine,
brakes and tyres depend largely on the way you drive the vehicle. By
adopting an economical driving style and anticipating the traffic
situation ahead, you can reduce fuel consumption by 10-15%. The
following section gives you some tips on lessening the impact on
the environment and reducing your operating costs at the same
time.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 230 Donnerstag, 26. Juli 2007 9:16 09
230
Your vehicle and the environment
Anticipate well in advance
Regular servicing
A car uses most fuel when accelerating. If you anticipate hazards
and speed changes well in advance, you will need to brake less and
thus accelerate less. Wherever possible, let the car slow down gradually with a gear engaged, for instance when you can see that the
next traffic lights are red. This takes advantage of the engine
braking effect, reducing wear on the brakes and tyres. Emissions
and fuel consumption will drop to zero due to the overrun fuel cutoff.
Regular servicing can establish a basis for good fuel economy
before you start driving. A well-serviced engine gives you the
benefit of improved fuel efficiency as well as maximum reliability
and an enhanced resale value. A badly tuned engine can consume
up to ten percent more fuel than necessary.
Change gear early to save fuel
An effective way of saving fuel is to change up quickly through the
gears. Running the engine at high rpm in the lower gears uses an
unnecessary amount of fuel.
Manual gearbox: Shift up to second gear as soon as possible. If
possible, we recommend shifting up to the next gear at approx.
2,000 rpm.
Automatic gearbox: Press the accelerator slowly and avoid using
the “kick-down” feature.
Avoid driving at high speed
Avoid travelling at top speed. Fuel consumption, exhaust emissions
and noise levels all increase very rapidly at higher speeds. Driving at
moderate speeds will help to save fuel.
Avoid short trips
The engine and emission control system need to reach their proper
working temperature in order to minimise fuel consumption and
emissions.
A cold engine uses disproportionately more fuel. The engine only
reaches its working temperature after about four kilometres, when
fuel consumption will return to a normal level. This is the reason
why we recommend avoiding short trips wherever possible.
Maintain the correct tyre pressures
Always make sure the tyres are inflated to the correct pressures
⇒ page 268 to save fuel. If the tyre pressures are just 0.5 bar too low,
this can increase the fuel consumption by as much as 5 %. Due to
the greater rolling resistance, under-inflation also increases tyre
wear and impairs handling.
Do not use winter tyres all through the year; they will increase fuel
consumption by up to 10 %.
Do not let the engine idle for longer than necessary
Avoid carrying unnecessary loads
It is worthwhile switching off the engine when waiting in a traffic
jam, at level crossings or at traffic lights with a long red phase. The
fuel saved after only 30 - 40 seconds is greater than the amount of
fuel needed to restart the engine.
Every kilo of extra weight will increase the fuel consumption, so it is
worth checking the luggage compartment occasionally to make
sure that no unnecessary loads are being transported.
The engine takes a very long time to warm up when it is running at
idling speed. Mechanical wear and pollutant emissions are also
especially high during this initial warm-up phase. It is therefore best
to drive off immediately after starting the engine. Avoid running the
engine at high speed.
A roof carrier is often left in place for the sake of convenience, even
when it is no longer needed. At a speed of 100-120 km/h your car will
use about 12 % more fuel as a result of the extra wind resistance
caused by the roof carrier - even when it is empty.
document_0900452a81b1b9de.book Seite 231 Donnerstag, 26. Juli 2007 9:16 09
Your vehicle and the environment
Save electrical energy
The engine drives the alternator to generate electricity. This means
that fuel consumption rises when more power is required for electrical equipment. Switch off electrical equipment when it is not
needed. Electrical equipment which uses a lot of electricity includes
the blower (at a high setting), the rear window heating and the seat
heating*.
•
•
•
231
Solvent-free adhesives
No CFCs used in production
Surplus materials used extensively for energy conversion and
building materials
•
•
•
Overall water consumption reduced
Heat recovery systems
Water-soluble paint
Environmental compatibility
Environmental protection is a top priority in the design, choice of
materials and production of your new Audi.
Design measures for economical recycling
•
•
•
•
Joints and connections designed for ease of dismantling
Modular construction to facilitate dismantling
Increased use of single-grade materials
Plastic parts and elastomers are labelled in accordance with ISO
1043, ISO 11469 and ISO 1629
Choice of materials
•
•
•
•
•
Nearly all materials used can be recycled
Similar types of plastics grouped together for easy recycling
Recycled materials used in manufacture
Reduced vapour emissions from plastics
CFC-free refrigerant in air conditioner
Compliance with the laws prohibiting the use of: Cadmium,
asbestos, lead, mercury and chrome VI.
Manufacturing methods
•
•
•
Using recycling material for manufacturing plastic parts
Solvent-free cavity sealing
Solvent-free wax for protecting the vehicles in transit
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 232 Donnerstag, 26. Juli 2007 9:16 09
232
Towing a trailer
Towing a trailer
Driving the vehicle with a trailer or
caravan
Technical requirements
The towing bracket must comply with certain technical
requirements.
Your car is intended mainly for transporting passengers and
luggage. However, if suitably equipped, it can also be used to tow a
trailer or caravan.
If the car is supplied with a factory-fitted towing bracket it will
already have the necessary technical modifications and meet the
statutory requirements.
A 13-pin socket is provided to make the electrical connection
between the car and the trailer. If the trailer has a 7-pin plug you can
use an adapter cable. This is available from Audi dealers.
WARNING
If a towing bracket is retrofitted, the installation should be carried
out by a qualified workshop.
•
In particular in high outside temperatures it is not possible to
drive up long steep gradients without a suitable cooling system.
The engine would then overheat.
If you do not load the trailer up to the maximum permitted trailer
weight, you can then climb correspondingly steeper gradients.
The maximum trailer weights listed are only applicable for altitudes
up to 1000 m above sea level. With increasing altitude the engine
power and therefore the car's climbing ability are impaired because
of the reduced air density, so the maximum trailer weight has to be
reduced accordingly. The weight of the car and trailer must be
reduced by 10% for every further 1000 m (or part thereof). This
figure refers to the combined weight of the (loaded) vehicle and
(loaded) trailer.
The figures for the draw bar weight that appear on the identification
plate of the towing bracket are for certification purposes only. The
correct figures for your specific vehicle, which may be lower than
these figures for the towing bracket, are given in the registration
documents. Also refer to ⇒ page 323.
Distributing the load
Distribute loads in the trailer so that heavy objects are as near to the
axle as possible. Loads carried in the trailer must be secured to
prevent them slipping.
Where possible, operate the trailer with the maximum permitted
draw bar weight on the ball joint of the towing bracket, but do not
exceed the specified limit.
Tyre pressure
Points to check before towing
Check the tyre pressures on your car and adjust for “full load” conditions (refer to the sticker listing the tyre pressures on the end face
of the driver's door). It may also be necessary to adjust the tyre pressures on the trailer according to the recommendations of the trailer
manufacturer.
Trailer weights
Exterior mirrors
Never exceed the maximum permitted trailer weights ⇒ page 323.
Check whether you can see enough of the road behind the trailer
with the standard mirrors. If this is not the case you should have
•
Incorrect installation can result in a safety risk.
document_0900452a81b1b9de.book Seite 233 Donnerstag, 26. Juli 2007 9:16 09
Towing a trailer
additional mirrors fitted. Both exterior mirrors should be mounted
on hinged extension brackets. Adjust the mirrors to give sufficient
vision to the rear.
•
The trailer connector must be properly secured in the vehicle
socket.
•
Vehicle speed must be higher than approx. 60 km/h.
Headlights
How trailer stabilisation works:
Before starting a journey, check the headlight beam settings with
the trailer hitched up. If necessary, alter the height of the headlight
beams by means of the headlight range control ⇒ page 60.
In many cases, the driver can stabilise a swaying trailer by manually
braking the vehicle.
Power supply
When you remove the ignition key the power supply to the trailer is
interrupted.
Removable ball joint coupling
Vehicles with a factory-fitted towing bracket are equipped with a
removable ball joint coupling. It is carried under the floor panel on
the left-hand side of the luggage compartment and is secured by a
strap.
Note
However, if the ESP detects that the trailer is swaying and this is
affecting the towing vehicle, it will automatically brake the vehicle
to stabilise the trailer by slowing it down. The warning lamp  will
light up in the instrument cluster. If possible, do not turn the
steering wheel at this stage.
In order to warn traffic behind you, the brake lights will come on
during this automatic braking operation.
A trailer weighing less than 70% of the kerb weight of the towing
vehicle may sway quite considerably without the trailer stabilisation
system intervening. This can happen when the swaying movements
of the light-weight trailer are not or hardly passed on to the towing
vehicle and are therefore not detected by the ESP.
We recommend having the car serviced between the normal inspection intervals if it used frequently for towing a trailer.
If the system for activating the trailer brake lights is defective, this
will be indicated in the instrument cluster display ⇒ page 37, “Bulb
monitor ”.
Applies to vehicles: with towing bracket
Trailer stabilisation system
Requirements for correct functioning of the trailer
stabilisation system
Trailer stabilisation helps to reduce the risk of the vehicle
skidding when towing a trailer.
If these conditions are not met in full, the trailer stabilisation system
will only intervene to a limited extent or not at all ⇒
.
The trailer stabilisation system is operational only when the ESP is
switched on and there is no malfunction in the ESP ⇒ page 17.
•
The electrical connection between the towing vehicle and the
trailer must be functioning correctly, without any defects.
When is the trailer stabilisation system activated?
•
•
Trailer stabilisation is active when the following requirements are
met:
•
•
The ESP must NOT be switched off ⇒ page 222,
Controls
Safety
Driving tips
233
The load on the trailer must be properly secured.
The tyre pressures on both the vehicle and the trailer must be
adapted to the load that is being carried.
Where possible, operate the trailer with the maximum permitted
draw bar weight.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 234 Donnerstag, 26. Juli 2007 9:16 09
234
Towing a trailer
•
The trailer overrun brake must be set correctly. This is important
to ensure that the trailer can be braked correctly, to avoid the vehicle
and trailer “jack-knifing” and to prevent excess braking of the trailer.
Notes on towing
At low outside temperatures, both the towing vehicle and the
trailer should be fitted with winter tyres.
Weight distribution
•
WARNING
It is essential that you adjust your speed to suit the weather, road
and traffic conditions. Do not let the trailer stabilisation system
tempt you into taking any risks when driving – this can cause accidents.
Driving with a trailer always requires extra care.
Try to avoid towing a loaded trailer with an unladen vehicle. If this
cannot be avoided, drive extra slowly to allow for the unbalanced
weight distribution.
Speed
•
The stability of the car and trailer is reduced with increasing speed.
For this reason it is advisable not to drive at the maximum permissible top speed in unfavourable road, weather or wind conditions.
This applies especially on a downhill gradient.
•
You should always reduce speed immediately if the trailer shows
the slightest sign of swaying. Never try to stop the swaying by accelerating further.
The ESP and trailer stabilisation system cannot defy the laws
of physics. This should be kept in mind, particularly on slippery
and wet roads and when towing a trailer with a light load.
The trailer stabilisation system is functional, regardless of
whether the trailer has a mechanical overrun brake or not.
The trailer stabilisation system is not always able to detect
swaying of trailers with a light load and will therefore not intervene.
Always brake in good time. If the trailer has an overrun brake, apply
the brakes gently at first and then firmly. This will prevent the jerking
that can be caused by the trailer wheels locking. Change down in
good time before going down a steep hill so that you can use the
engine braking effect to slow down the vehicle.
•
Swaying and pitching can be reduced by stabiliser aids. We recommend having stabiliser aids installed when towing trailers with a
high trailer weight. They can be purchased and installed at an Audi
dealer.
•
• A trailer can still “jack-knife” on slippery roads with little grip,
even if the towing vehicle is equipped with the trailer stabilisation
system.
Trailers with a high centre of gravity may even tip over before
they start to sway sideways.
•
If you are not towing a trailer, but the trailer socket is being
used (e.g. for an illuminated bicycle rack), the trailer stabilisation
system may be activated in extreme driving conditions.
•
Please note the additional information and warnings
⇒ page 234.
Overheating
When climbing long hills in hot weather with the engine running
fast in low gear, you should keep an eye on the coolant temperature
gauge ⇒ page 11. Reduce speed immediately if the needle moves to
the top end of the scale. If the temperature warning lamp  in the
instrument cluster should start flashing, stop the car and let the
engine cool down by running it at idling speed for a few minutes.
document_0900452a81b1b9de.book Seite 235 Donnerstag, 26. Juli 2007 9:16 09
Towing a trailer
Applies to vehicles: with towing bracket
Accessories
Before mounting equipment and accessories (e.g. bicycle
rack) please observe the following notes.
235
by the manufacturer for use on the ball joint. If you mount unsuitable equipment, this can cause damage to the towing bracket. In an
extreme case, damage to the towing bracket could cause it to break
⇒
.
WARNING
•
If you wish to mount equipment which has not been approved
by Audi please ensure that it is suitable for use on Audi vehicles.
•
Use of unsuitable equipment can result in severe damage to
the towing bracket. The towing bracket could then break while
pulling a trailer and cause an accident.
Fig. 234 Load distribution of equipment and
accessories
The equipment/accessories mounted must not protrude more than
1 .
700 mm from the ball joint A
The total weight (mounted equipment plus the load) must not
exceed 75 kg.
The maximum load depends on where the centre of gravity lies.
The maximum weight decreases as the distance between the centre
1 increases.
of gravity and the ball joint A
•
Never use tools of any kind when fitting and removing the ball
joint. This could damage the mechanism which locks the ball joint
in place and impair its safety (accident risk).
Removable towing bracket
Applies to vehicles: with removable towing bracket
Introduction
Special care is required when fitting and removing the
towing bracket.
The following limits apply:
If the distance is 300 mm, the total weight (incl. the equipment
A must not exceed 75 kg.
mounted) A
If the distance is 600 mm, the total weight (incl. the equipment
B must not exceed 35 kg.
mounted) A
Only bicycle racks for a maximum of three bicycles may be used.
Fig. 235 Luggage
compartment with
towing bracket
Equipment mounted on the towing bracket
We recommend that you only mount equipment (e.g. bicycle rack)
which has been approved by Audi on the ball joint. If you wish to
attach other equipment please make sure that it has been approved
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 236 Donnerstag, 26. Juli 2007 9:16 09
236
Towing a trailer
The removable ball joint attachment for the towing bracket is
carried under the floor panel on the left-hand side of the luggage
compartment and is secured by a strap.
Applies to vehicles: with removable towing bracket
Fitting the ball joint (step 1)
The ball joint can be fitted and removed by hand.
WARNING
•
Never use tools of any kind when fitting and removing the ball
joint. This could damage the mechanism which locks the ball joint
in place and impair its safety (accident risk).
•
Secure the ball joint again with the strap when you have
finished using it.
•
Fig. 236 Area below
rear bumper: Folding
down the socket
Note
Do not attempt to modify or repair the ball joint or other towing
bracket components.
•
Should you have any difficulties when using the towing bracket,
or suspect that it is not fitted properly, contact a qualified workshop.
•
Before setting off, always check that the ball joint is secured
properly ⇒ page 238.
•
Never disengage the ball joint with the caravan / trailer still
hitched or with a bicycle rack or similar accessory still attached.
•
Fig. 237 Socket
(folded down)
It is advisable to remove the ball joint when you are not towing a
trailer. Fold the socket back to its original position so that the
mounting fixture is properly closed.
– Fold the socket unit all the way out in the direction of the
arrow ⇒ fig. 236.
The ball joint must be removed if you intend to clean the car with
a steam cleaning attachment. Make sure that the mounting fixture
is properly closed.
– The cover piece is held automatically in the open position.
For installation and removal of the ball joint we recommend that
the gloves provided be used.
– Check that the mounting for the towing bracket, which
will now have become visible -arrow- ⇒ fig. 237, is free of
dirt, and clean if necessary ⇒
.
•
•
document_0900452a81b1b9de.book Seite 237 Donnerstag, 26. Juli 2007 9:16 09
Towing a trailer
– Also check the shaft section of the ball joint and its associated mechanical parts to make sure they are clean and
undamaged.
237
The ball joint can only be installed if the internal spring mechanism
is in the ready position.
Continued ⇒ page 237, “Fitting the ball joint (step 3)”.
Continued ⇒ page 237, “Fitting the ball joint (step 2)”.
Applies to vehicles: with removable towing bracket
Fitting the ball joint (step 3)
WARNING
It is important to keep the mounting fixture clean. Otherwise the
ball joint may fail to engage securely (accident risk).
Applies to vehicles: with removable towing bracket
Fitting the ball joint (step 2)
Fig. 239 Removable
towing bracket:
Setting the spring
mechanism to the
"ready" position
Fig. 238 Removable
towing bracket: Ball
joint
The spring mechanism inside the ball joint must
be in the "ready" position.
2 ⇒ fig. 238 on the knob is
– Check that the red marking A
inside the green zone on the ball joint.
1 is inside the hole in the
– Check that the locking ball A
shaft section of the ball joint.
– Check that the knob protrudes visibly from the ball joint,
3 between the knob and the
so that there is a clear gap A
ball joint.
Controls
Safety
Driving tips
Fig. 240 Removable
towing bracket:
Inserting the ball joint
Setting the spring mechanism to the "ready"
position (if required)
4 ⇒ fig. 239 for locking the ball joint into
– Insert the key A
the lock on the knob and turn it clockwise.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 238 Donnerstag, 26. Juli 2007 9:16 09
238
Towing a trailer
a , hold and turn in direc– Pull out the knob in direction A
b until the locking ball A
5 engages ⇒
tion A
.
Applies to vehicles: with removable towing bracket
Fitting the ball joint (step 4)
Inserting the ball joint
– With the spring mechanism in the “ready” position,
insert the ball joint into the mounting fixture and push it
upwards ⇒ page 237, fig. 240 in the direction indicated
(arrow) ⇒
. The spring mechanism should then
engage automatically with an audible click.
– Lock the ball joint by turning the key anti-clockwise.
Fig. 241 Removable
towing bracket: Safety
check
– Take out the key and press the cover cap provided onto
the lock.
Continued ⇒ page 238, “Fitting the ball joint (step 4)”.
WARNING
•
If it is not possible to set the spring mechanism to the "ready"
position as described above, do not use the ball joint. Please take
your vehicle to a qualified workshop.
Fig. 242 Area below
rear bumper: Electrical
socket for trailer
•
To avoid injury, keep your hands away from the knob and the
cover piece when inserting the ball joint into the mounting fixture.
Safety check
Note
Make sure that the knob can turn freely when the ball joint is
inserted.
6 ⇒ fig. 241 on the knob
– Check that the green marking A
is inside the green zone on the ball joint.
– Check that the knob is directly against the ball joint, so
7 between the knob and the ball
that there is no gap A
joint.
– Check that the ball joint is locked and the key is removed
(so that the knob cannot be pulled out).
document_0900452a81b1b9de.book Seite 239 Donnerstag, 26. Juli 2007 9:16 09
Towing a trailer
239
– Check that the ball joint fits tightly in the mounting
fixture (try moving it about to check).
Electrical socket for trailer
– The cable of the towing bracket can be connected to the
socket ⇒ page 238, fig. 242.
Fig. 244 Area below
rear bumper: Folding
up the socket
If the safety check is not satisfactory, the ball joint must be fitted
again properly.
WARNING
To avoid accidents, the ball joint must meet all the safety requirements listed in the safety check. The towing bracket must not be
used if any one of these requirements is not met. If this is the case,
you should contact a qualified workshop.
8 ⇒ fig. 243 in
– Take off the cover cap and insert the key A
the lock on the knob.
– Unlock the ball joint by turning the key clockwise.
– Take hold of the ball joint and pull out the knob in direca.
tion A
– Keep hold of the knob and turn it as far as it will go in
b .
direction A
Applies to vehicles: with removable towing bracket
Removing the ball joint
– Release the knob. The spring mechanism will remain in
the "ready" position ⇒
.
– Pull the ball joint down out of the mounting fixture.
– Then swivel the socket up ⇒ fig. 244 as far as it will go.
The mounting fixture will be closed automatically.
Fig. 243 Removable
towing bracket:
Removing the ball joint
– Put away the ball joint attachment under the floor panel
in the luggage compartment.
WARNING
Make sure that the socket unit has closed off the mounting fixture
of the towing bracket properly. Otherwise the ball joint may fail to
engage securely if dirt accumulates in the mounting fixture.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 240 Donnerstag, 26. Juli 2007 9:16 09
240
Towing a trailer
Applies to vehicles: with towing bracket
WARNING
Towing bracket (retrofitting)
If required, the vehicle can be retrofitted with a towing
bracket.
•
If a towing bracket is retrofitted, the installation should be
carried out by a qualified workshop.
•
If the towing bracket is incorrectly fitted, this could cause a
safety risk.
•
For your own safety, please observe the instructions provided
by the manufacturer of the towing bracket.
Caution
Fig. 245 Positions of
securing points (side
view)
Fig. 246 Positions of
securing points (from
above)
If a towing bracket is to be fitted after the car is purchased, this must
be done according to the instructions of the towing bracket manufacturer.
A in the illustrations
The securing points, which are marked by an A
⇒ fig. 245 and ⇒ fig. 246, are located under the vehicle.
Audi dealers are familiar with the method of installation and any
modifications which may be required for the cooling system.
If the connector socket is not fitted correctly, this could cause
damage to the vehicle's electrical system.
document_0900452a81b1b9de.book Seite 241 Donnerstag, 26. Juli 2007 9:16 09
Towing a trailer
Controls
Safety
Driving tips
General maintenance
Self-help
241
Technical data
document_0900452a81b1b9de.book Seite 242 Donnerstag, 26. Juli 2007 9:16 09
242
document_0900452a81b1b9de.book Seite 243 Donnerstag, 26. Juli 2007 9:16 09
General maintenance
243
document_0900452a81b1b9de.book Seite 244 Donnerstag, 26. Juli 2007 9:16 09
244
Care of vehicle and cleaning
Care of vehicle and cleaning
General notes
Regular care helps to maintain the value of the vehicle.
Regular and careful care helps to maintain the value of the vehicle.
This may also be one of the requirements for upholding any
warranty claims in the event of corrosion or paint defects.
Audi dealers and specialist retailers carry stocks of suitable car care
products. Please follow the instructions for use on the packaging.
WARNING
•
Cleaning products and other materials used for car care can
damage health if misused.
•
Car care products can contain toxic substances and must
always be kept in a safe place out of reach of children.
•
For the sake of the environment
do to the paintwork. High temperatures (for instance in strong
sunlight) further intensify the corrosive effect.
After the period when salt is put on the roads it is important to have
the underside of the vehicle washed thoroughly.
Automatic car washes
Before going through a car wash, be sure to take the usual precautions such as closing the windows and sunroof. If the vehicle has
special accessories such as spoilers or a roof carrier or two-way
radio aerial, etc., it is advisable to consult the car wash operator.
It is best to use a car wash without revolving bristles if possible.
Washing your car with a high-pressure cleaner
When cleaning the vehicle with a high-pressure cleaner, always
follow the operating instructions for the equipment. This applies
particularly to the operating pressure and the spraying distance. Do
not hold the spray nozzle too close to soft materials, such as rubber
hoses or seals.
When purchasing car care products, try to select ones which are
not harmful to the environment.
Do not use a nozzle that sprays the water out in a direct stream or
one that has a rotating jet for forcing off dirt.
Surplus cleaning materials should not be disposed of together
with ordinary household waste.
Washing the car by hand
Care of exterior
Then clean the vehicle with a soft sponge, glove or brush, using only
slight pressure. You should start on the roof and work down. Special
car shampoo should only be used for very persistent dirt.
•
Washing the vehicle
When washing the car by hand, use plenty of water to soften the dirt
first, and rinse off as well as possible.
Rinse the sponge or glove thoroughly and often.
The longer substances like insects, bird droppings, resinous tree
sap, road dirt, industrial deposits, tar, soot or road salt and other
aggressive materials remain on the vehicle, the more damage they
Wheels, sills and similar should be cleaned last. Use a second
sponge for this.
document_0900452a81b1b9de.book Seite 245 Donnerstag, 26. Juli 2007 9:16 09
Care of vehicle and cleaning
Even if a wax solution is used regularly in the car wash, it is advisable to protect the paint with a coat of wax at least twice a year.
WARNING
•
Do not wash the vehicle with the ignition switched on – risk of
accident.
•
Do not clean the underside of the car or inside the wheel arches
without protecting your hands and arms. You may cut yourself on
sharp metal parts.
•
Take care when washing the car during the winter: moisture
and ice on the brakes may affect braking efficiency – this could
cause an accident.
•
245
In the summer, you will find it is much easier to remove dead insects
(which accumulate on the bumper and the front of the bonnet) if the
car has been waxed recently.
Polishing
Polishing is only necessary if the paint has lost its shine, and the
gloss cannot be brought back by putting on wax.
The car must be waxed after polishing if the polish used does not
contain wax compounds to seal the paint.
Caution
Do not wash the vehicle in direct sunlight – otherwise the paint
can be damaged.
•
Do not use insect sponges or abrasive household sponges, etc.
– they can damage the surfaces.
•
Caution
Matt painted and plastic parts must not be treated with wax or
polish.
The headlights should only be washed with water – do not wipe
them with a dry cloth or sponge. It is best to use soapy water.
Ornamental trim and mouldings
Never wash tyres with a jet that sprays the water out in a direct
stream. This could damage the tyres – even if the spray is kept at a
distance and only used for a very short time.
The metal brightwork on the body is made of aluminium rather than
chrome (for environmental reasons).
•
For the sake of the environment
The car should only be washed in special wash bays. This prevents
oily water from getting into the public drains. In some districts,
washing vehicles anywhere else may be prohibited.
Dirt or marks on the trim mouldings should be removed with an
acid-free cleaning agent (do not use a chrome cleaner). Body polish
is also unsuitable for use on trim mouldings. The intensive cleaning
fluids often used before the car goes into a car wash may contain
alkaline substances, which can cause dull or milky patches when
they dry out.
Audi dealers carry stocks of cleaning products which have been
tested for use on your vehicle and are not harmful to the
environment.
Waxing and polishing
Waxing
Waxing protects the paintwork. It is time to apply a good coat of wax
when water no longer forms droplets and rolls off the clean paintwork.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 246 Donnerstag, 26. Juli 2007 9:16 09
246
Care of vehicle and cleaning
Plastic parts
Plastic parts will come clean with regular washing. If this is not sufficient, plastic parts should only be treated with a special solvent-free
plastic cleaning agent. Do not use paint cleaners, polishes or wax on
plastic parts.
WARNING
Do not use water-repellent coatings on the windscreen. In bad visibility conditions such as light rain, low sun or when driving at
night these coatings can cause increased dazzle, which is a
serious safety hazard. Such coatings can also cause the wiper
blades to judder.
Paint damage
Minor damage to the paint, such as scratches or stone chips, should
be touched up without delay before the metal starts to corrode. Suitable touch-up brushes or sprays for your car can be obtained from
an Audi dealer.
The number of the original paint finish on the vehicle is given on the
data sticker ⇒ page 321.
If corrosion is already visible it must be thoroughly removed by a
qualified workshop.
Windows
•
Caution
Remove snow and ice from windows and mirrors with a plastic
scraper only. To avoid scratches caused by dirt on the glass, the
scraper should only be pushed in one direction and not moved to
and fro.
•
The heating element for the rear window is located on the inner
side of the window. To avoid damaging the heating element, do not
put stickers on the inner side of the window.
•
Never use warm or hot water to remove snow and ice from
windows and mirrors. This could cause the glass to crack!
Rubber seals (weatherstrips)
Clear vision is an essential safety factor.
The windscreen must not be cleaned with insect remover or wax,
otherwise the windscreen wipers will not function properly
(juddering).
Traces of rubber, oil, grease or silicone can be removed with a
window cleaning solution or a silicone remover. Wax residue can
only be removed with a special cleaner. Your Audi dealer will be able
to provide you with more detailed information.
The windows should also be cleaned on the inside at regular intervals.
Use a separate cloth or chamois to dry the windows. Cloths used for
waxing and polishing contain residues that will cause smears on the
glass.
The weatherstrips will remain pliable and last longer if they are
occasionally treated with a suitable care product (for example silicone spray). This will also prevent premature ageing and leaks. The
doors will be easier to open as well. If they are kept pliable, the door
seals will be less likely to freeze up in the winter.
Wheels
The wheels require regular attention to preserve their appearance.
It is important to remove road salt and brake dust by washing the
wheels at regular intervals, otherwise the finish will be impaired.
document_0900452a81b1b9de.book Seite 247 Donnerstag, 26. Juli 2007 9:16 09
Care of vehicle and cleaning
After washing, the wheels should only be cleaned with an "acidfree" cleaning agent for alloy wheels. This is available from Audi
dealers and specialist retailers. Never leave the cleaning agent on
the rims for any longer than specified in the instructions before
rinsing it off. If the wheel cleaner fluid contains acid it can attack the
surfaces of the wheel bolts.
Car polish or other abrasive agents should not be used. If the
protective paint coating is damaged by stone chips etc., the
damaged area should be touched up immediately.
247
•
To avoid any possibility of damage, do not let any liquid get
inside the control console.
Plastic parts and leatherette
Plastic parts and leatherette can be cleaned with a damp cloth. If
this is not sufficient, plastic parts and leatherette should only be
treated with a special solvent-free plastic cleaner.
Textile covers and trim parts
WARNING
Please note when cleaning the wheels that water, ice and road salt
can impair the effectiveness of the brakes – this can cause an
accident.
Care of interior
Textile covers and trim parts (e.g. seats, door trim) should be
cleaned regularly with a vacuum cleaner. This will remove surface
dirt which could otherwise be rubbed into the textile material
during use. Do not use steam cleaners, as the steam could carry the
dirt deeper into the textile material.
Normal cleaning
Sound system / MMI* display screen and MMI
control console*
We recommend that you use a soft sponge or lint-free, micro-fibre
cloth for normal cleaning. Only use brushes on floor coverings and
mats, as other textile surfaces could become damaged.
The display screen can be cleaned with a soft cloth and a special
“LCD cleaner” (available from retailers of electrical goods). Moisten
the cloth with a small amount of the cleaning fluid.
In the case of normal surface dirt you can use a foam cleaner. Use a
sponge to spread the foam on the textile surface and to work it into
the material lightly. However, make sure that the textile material
does not become soaking wet. Then dab off the foam with a dry and
absorbent cloth (e.g. a micro-fibre cloth) and vacuum off any
residue once the surface is completely dry.
Clean the MMI control console with a fine brush first to prevent any
dirt from getting in between the control buttons and the housing.
We then recommend wiping the MMI control console using a cloth
moistened with washing-up liquid and water.
Caution
To avoid scratching the screen, do not wipe the display with a dry
cloth.
Controls
Safety
Driving tips
Removal of stains
To treat stains caused by spilled drinks (coffee, fruit juice or similar)
make up a solution with a mild detergent for sensitive fabrics and
apply it with a sponge. If the stains are difficult to remove, a
washing paste can be applied directly onto the stain and worked
into the fabric. The surface will then have to be wiped with clear
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 248 Donnerstag, 26. Juli 2007 9:16 09
248
Care of vehicle and cleaning
water to remove any residue left by the paste. To do so, use a damp
cloth or sponge and then dab the stain with an absorbent cloth.
bear this in mind if children or pets often travel in the car, or if there
are other factors that could lead to damage.
Treat chocolate or make-up stains with a washing paste and then
rinse off with water (using a damp sponge).
Types of leather with a coloured surface coating are likely to be
more resistant to damage. This has a great advantage for day-to-day
use. However, this means that the typical natural characteristics of
the surface are less apparent, though this does not affect quality.
A spirit-based cleaner can be used to remove grease, oil, lipstick or
ball point pen. Then dab the dissolved grease or colour particles off
with an absorbent cloth or similar. You may also have to treat the
stain once more using washing paste and water.
If the covers or textile trim panels are badly soiled we recommend
that you have them cleaned by a professional cleaning company.
Note
Please make sure you close any velcro fasteners on your clothing, as
these could otherwise damage the upholstery.
Applies to vehicles: with leather upholstery
Natural leather
Audi does everything possible to preserve the special
qualities of leather as a natural product.
General notes
We have a wide selection of leathers. The main type used is nappa
in various forms, that is leather with a smooth surface in a selection
of colours.
The amount of dye used determines the appearance and properties
of leather. If the leather is left in a more natural state, it retains its
typical natural appearance and is pleasant and comfortable for the
seat occupants. Fine veins, healed scars, insect bites, wrinkles and
a subtle variation in shading remain visible; these are the characteristic features of genuine natural leather.
Natural napped leather does not have a protective surface coating
of dye. It is therefore somewhat more prone to damage. You should
Cleaning and care
Because of the natural properties of the specially selected hides
employed, the finished leather has a certain sensitivity to grease
and dirt, etc. so a degree of care is required in everyday use and
when looking after the leather. Dark clothing (especially if damp or
incorrectly dyed) may stain leather upholstery. Dust and grit in the
pores and seams can have an abrasive effect and damage the
surface of the leather. Therefore leather should be cleaned at
regular intervals, depending on the actual amount of use. When
they have been in use for a certain time, your car seats will acquire
a typical and distinctive patina. This is characteristic for real leather
upholstery, and is a sign of genuine quality.
To maintain the value of natural leather you should note the
following points:
•
Caution
Avoid exposing leather to direct sunlight for long periods, otherwise it may tend to lose some of its colour. If the car is left for a
prolonged period in the bright sun, it is best to cover the leather.
•
Sharp-edged objects on clothing, such as belts, zip fasteners,
rivets or similar, can also leave permanent scratches and rough
marks on the surface of the leather.
•
Note
Use a suitable impregnating cream with ultra-violet protection at
regular intervals and after cleaning. This cream will nourish and
moisturise the leather, keep it supple and able to breathe. In addition, it will also help to protect the surface of the leather.
document_0900452a81b1b9de.book Seite 249 Donnerstag, 26. Juli 2007 9:16 09
Care of vehicle and cleaning
•
Remove stains from fresh ball-pen and other inks, lipstick, shoe
cream and similar stains as soon as possible.
– Remove fresh fat-based stains on the surface such as
butter, mayonnaise, chocolate, etc. with an absorbent
cloth or kitchen roll or with the cleaning agent from the
care set.
Preserve the colour of the leather. A special coloured cream will
renew the colour of the leather when required and will eliminate
differences in colour.
– Treat fat-based, dried-in stains with grease-dissolving
spray.
Clean the leather every 2 to 3 months and remove fresh dirt as
necessary.
•
•
Applies to vehicles: with leather upholstery
Cleaning and care of leather upholstery
Natural leather requires an extra degree of attention and
care.
Normal cleaning
– Treat less common stains such as ball-pen and other
inks, felt-tip pens, nail polish, dispersion paint, shoe
cream etc. with a special leather stain remover.
Leather care products
– The leather should be treated regularly (about twice a
year) with a special leather-care product.
– Moisten a cotton or woollen cloth with water and wipe
over the leather surfaces.
– Apply the cream very sparingly.
More stubborn dirt
Should you have any questions regarding the care and cleaning of
the leather upholstery in your vehicle, we recommend that you
contact your Audi dealer. The staff there will gladly provide you with
further information on cleaning and care of your upholstery and on
our complete range of leather care products:
– More stubborn dirt can be removed using a mild soap
solution (pure liquid soap: two tablespoons dissolved in
one litre of water).
– It is very important not to let the water soak through the
leather or penetrate into the seams.
– Then wipe off with a soft, dry cloth.
Removal of stains
– Remove fresh water-based stains such as coffee, tea,
juices, blood etc. with an absorbent cloth or kitchen roll,
dried-on stains with the cleaning agent from the care set.
249
– Then wipe off with a soft, dry cloth.
•
•
•
•
•
Cleaning and care set
Coloured leather-care cream
Stain remover for ball-pen inks, shoe cream etc.
Grease dissolving spray
New products and further developments
Caution
On no account use solvents (such as petrol, turpentine), wax polish,
shoe cream or similar materials.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 250 Donnerstag, 26. Juli 2007 9:16 09
250
Care of vehicle and cleaning
Applies to vehicles: with Alcantara seat covers
Cleaning Alcantara
Removing dust and dirt
Seat belts
Seat belts should be looked after properly to ensure that
they give the full protection.
– Moisten a cloth just a little and wipe down the seat
covers.
– Keep the seat belts clean.
Removing stains
– Check the condition of the seat belts at regular intervals.
– Moisten a cloth with lukewarm water or diluted methylated spirits.
Very dirty belts may not retract properly.
– Dab at the stain. Start at the outside and work inwards.
– For cleaning, use a mild soap solution.
Make sure that the inertia reel seat belts are completely dry before
allowing them to retract.
– Dry the area you have cleaned with a soft cloth.
Do not use leather cleaning products on Alcantara seat covers.
You may use a suitable shampoo on dust and dirt.
Dust and grit in the pores and seams can have an abrasive effect
and damage the surface of the leather. If the car is left standing in
the sun for long periods, the leather should be protected against
direct sunlight to prevent it from fading. However, slight colour variations will arise in normal use.
•
Caution
Do not use solvents, wax polish, shoe cream, stain removers,
leather cleaning products or any similar products on Alcantara.
•
To avoid damage, stubborn stains should be removed by a qualified workshop.
•
On no account use brushes, hard sponges or similar utensils.
•
•
Caution
Do not remove the seat belts from the vehicle to clean them.
Do not use chemical cleaning agents on the seat belts, as this
can damage the webbing. Ensure that the belts do not come into
contact with corrosive fluids.
•
If you find any damage to the belt webbing, belt fittings, the belt
retractor or the buckle, the belt in question must be replaced by a
qualified workshop.
document_0900452a81b1b9de.book Seite 251 Donnerstag, 26. Juli 2007 9:16 09
Fuel and filling the tank
251
Fuel and filling the tank
Petrol
•
Applies to vehicles: with petrol engine
•
Even one tankful of leaded fuel would permanently impair the
efficiency of the catalytic converter.
High engine speed and full throttle can damage the engine when
using petrol with an octane rating lower than the correct grade for
the engine.
Petrol grade
The correct grade of petrol is listed inside the fuel tank
flap.
The vehicle is equipped with a catalytic converter and must only be
run on unleaded petrol. Unleaded petrol must comply with the
European EN 228 standard. The petrol grades have different octane
ratings (RON). If, in exceptional circumstances, the correct octane
rating is not available, please note the following:
•
For engines which require Premium unleaded petrol (95 RON)
according to ⇒ page 323, “Performance, weights and dimensions”:
Regular unleaded fuel with 91 RON can also be used. This will,
however, result in a slight loss of power.
•
For engines which require Super Plus unleaded petrol (98 RON)
according to ⇒ page 323, “Performance, weights and dimensions”:
Premium unleaded fuel with 95 RON can also be used. This can,
however, result in a slight loss of power under certain driving conditions. – If premium unleaded petrol is not available, the engine can
be run on regular unleaded petrol with 91 RON as an emergency
measure. In this case only use moderate engine speeds and a light
throttle. Fill up with premium or Super Plus petrol as soon as
possible.
Diesel
Applies to vehicles: with diesel engine
Diesel fuel
Please note the information on the inside of the fuel tank
flap.
Diesel fuel must comply with the European EN 590 standard. It must
have a cetane number (CN) of at least 51. The cetane number indicates the ignition quality of the diesel fuel.
Winter-grade diesel
Diesel fuel can thicken in winter. For this reason petrol stations in
some countries also offer winter diesel.
•
Caution
The vehicle is not designed for the use of biodiesel (FAME fuel).
The fuel system would be damaged if you used biodiesel.
•
•
Do not mix fuel additives (“thinners”, petrol or similar additives)
with the diesel fuel.
Caution
Petrol complying with the EN 228 standard can contain small
quantities of ethanol. However, “bioethanol fuels”, which are
retailed under various different names such as E50 and E85, and
which contain a large proportion of ethanol, must not be put into
the vehicle, as this would damage the fuel system.
Controls
Safety
Driving tips
•
If poor-quality diesel fuel is used, it may be necessary to drain
the water separator on the fuel filter more frequently than is specified in the Service Schedule. We recommend having this done by a
specialist workshop. If water is allowed to collect in the filter, this
can cause engine performance problems.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 252 Donnerstag, 26. Juli 2007 9:16 09
252
Fuel and filling the tank
Filling the tank
Closing the tank cap
Filling the tank
– Screw on the tank cap clockwise until it cannot be turned
further.
– Press the left side of the flap to close it (you should hear
it click into place).
When the automatic filler nozzle is operated correctly it will switch
itself off as soon as the tank is “full”. Do not try to put in more fuel
after the nozzle cuts out, as this will fill the expansion chamber in
the fuel tank.
Fig. 247 Vehicle as
seen from the rear
right: Opening fuel
tank flap
The correct fuel grade for your vehicle is given on a sticker on the
inside of the tank flap. Further notes on fuel ⇒ page 251.
The tank capacity of your vehicle is given in the Technical data
section ⇒ page 321.
WARNING
Fuel is highly inflammable and can cause serious burns and other
injuries.
•
For safety reasons always switch off the auxiliary heating*
before refuelling the vehicle.
Fig. 248 Fuel tank flap
with tank cap attached
The flap that covers the tank cap is unlocked and locked
automatically by the central locking.
Unscrewing the tank cap
– Press the left side of the flap to open it ⇒ fig. 247 -arrow-.
– Unscrew the tank cap anti-clockwise.
– Hook the cap onto the open flap ⇒ fig. 248.
•
For safety reasons we do not recommend carrying a spare fuel
canister in the vehicle. The canister could become damaged in an
accident and leak.
•
Observe all relevant statutory regulations on using, storing and
transporting spare fuel canisters.
•
When filling your tank or a spare fuel canister with fuel, do not
smoke and keep away from naked flames. Risk of explosion!
•
If, in exceptional circumstances, you have to carry a spare fuel
canister, please observe the following warnings:
− Never fill fuel into the spare fuel canister with the canister
placed in or on top of the vehicle. An electrostatic charge could
build up during filling, causing the fuel vapour to ignite. Danger
of explosion. Always place the canister on the ground to fill it.
document_0900452a81b1b9de.book Seite 253 Donnerstag, 26. Juli 2007 9:16 09
Fuel and filling the tank
WARNING (continued)
Releasing the tank flap manually
− Insert the filler nozzle as far as possible into the spare fuel
canister.
The tank flap can be released manually if the central
locking system should fail to operate.
253
− If the spare fuel canister is made of metal, the filler nozzle
must be in contact with the canister during filling. This helps
prevent an electrostatic charge building up.
− Make sure you never spill fuel in the vehicle or in the luggage
compartment. Fuel vapour is explosive. Risk of fatal accident!
•
Caution
Fig. 249 Luggage
compartment:
Releasing the fuel tank
flap manually
If any fuel is spilt onto the vehicle, it should be removed immediately, as it could otherwise damage the paintwork.
•
Never run the tank completely dry. If there is an irregular fuel
supply, misfiring can occur. As a result unburnt fuel can enter the
exhaust system and cause damage to the catalytic converter(s).
•
When filling the fuel tank after having run it completely dry on a
vehicle with a diesel engine the ignition must be switched on for at
least 30 seconds without starting the engine. When you then start
the engine it may take longer than normal (up to one minute) for the
engine to start firing. This is because air needs to be bled from the
fuel system while starting.
The manual release mechanism is located behind the side
trim on the right of the luggage compartment.
– Open the right-hand side trim.
– Release the ring from its holder and pull the ring
⇒ fig. 249. You should now be able to open the tank flap
in the usual way ⇒ page 252.
For the sake of the environment
Do not try to put in more fuel after the automatic filler nozzle has
switched off; this may cause the fuel to overflow if it becomes warm.
Note
The tank flap is not locked when you lock the vehicle from the
inside.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 254 Donnerstag, 26. Juli 2007 9:16 09
254
Checking and topping up fluids
Checking and topping up fluids
Bonnet
Opening the bonnet
Releasing the bonnet
The bonnet is released from inside the vehicle.
Fig. 251 Release catch
under the bonnet
Fig. 250 Detail of footwell on driver's side:
Release lever
Before opening the bonnet make sure that the windscreen
wiper arms are not lifted away from the glass. Otherwise the
paint may get damaged.
– Open the driver's door.
– Lift the bonnet slightly ⇒
– Pull the lever under the dashboard in the direction indicated (arrow) ⇒ fig. 250.
– Press the release catch under the bonnet upwards
⇒ fig. 251. This will release the arrester hook.
The bonnet springs out of its lock.
– Open the bonnet.
.
The bonnet is held open by two gas-filled struts.
WARNING
To avoid the risk of being scalded, never open the bonnet if you see
steam or coolant escaping from the engine compartment. Wait
until no steam or coolant can be seen before opening the bonnet.
document_0900452a81b1b9de.book Seite 255 Donnerstag, 26. Juli 2007 9:16 09
Checking and topping up fluids
Working on components in the engine
compartment
255
WARNING (continued)
Extra caution is necessary when working on components
in the engine compartment.
Always be aware of the danger of injury and scalding as well as the
risk of accident or fire when working in the engine compartment
(e.g. when checking and refilling fluids). Always observe the warnings listed below and follow all normal safety precautions. The
engine compartment of any motor vehicle is a potentially
hazardous area. ⇒
.
•
Vehicles with automatic gearbox: Never open the throttle inadvertently (for instance by hand from the engine compartment) if a
gear is engaged while the vehicle is stationary with the engine
running. The vehicle could otherwise start moving immediately
and possibly cause an accident.
•
Observe the following additional warnings if work on the fuel
system or the electrical system is necessary:
− Always disconnect the battery.
− Do not smoke.
− Never work near naked flames.
− Always keep an approved fire extinguisher immediately
available.
WARNING
•
•
•
•
•
•
•
Switch off the engine.
Remove the ignition key.
Caution
Apply the parking brake.
When topping up fluids make sure the correct fluid is put into the
correct filler opening. This can otherwise cause serious malfunctions or engine damage.
Put the gear lever in neutral or selector in P.
Wait for the engine to cool down.
Keep children away from engine compartment.
Never spill fluids on hot engine components. These fluids can
cause a fire (e.g. radiator anti-freeze).
•
Take care not to cause short circuits in the electrical system,
especially when working on the battery.
•
Do not touch the radiator fan when the engine is hot. The fan
may start running suddenly.
•
Do not unscrew the cap on the expansion tank when the engine
is hot. The cooling system is under pressure.
•
Protect face, hands and arms by covering the cap with a large,
thick rag to protect against escaping coolant and steam.
For the sake of the environment
Inspect the ground underneath your vehicle regularly so that any
leaks are detected at an early stage. If you find oil spots or other
fluids, have your vehicle inspected by a qualified workshop.
Note
On right-hand drive vehicles* some of the containers / reservoirs
mentioned below are located on the other side of the engine
compartment.
•
If any tests have to be performed with the engine running,
there is an extra safety risk from the rotating parts, such as the
drive belts, alternator and radiator fan, etc., and from the highvoltage ignition system.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 256 Donnerstag, 26. Juli 2007 9:16 09
256
Checking and topping up fluids
Closing the bonnet
Engine compartment layout
– To close the bonnet, pull it down to overcome the spring
pressure.
Engine compartment layout
– Then let it drop into the catches; do not press down ⇒
Main components for checking and refilling
.
WARNING
•
For safety reasons the bonnet must always be completely
closed when the vehicle is moving. After closing it always check
that it is properly secured. The bonnet must be flush with the adjacent body panels.
•
Should you notice that the bonnet is not safely secured when
the vehicle is moving, stop the vehicle immediately and close the
bonnet properly, otherwise it could cause an accident.
Fig. 252 Typical locations of fluid containers, engine oil dipstick and engine oil
filler cap
1
A
2
A
3
A
4
A
5
A
6
A
7
A
8
A
Jump-start terminal (+) under a cover . . . . . . . . . . . . . 265, 294
262
Brake fluid reservoir () . . . . . . . . . . . . . . . . . . . . . . . .
259
Engine oil filler cap () . . . . . . . . . . . . . . . . . . . . . . . .
258
Engine oil dipstick* (orange) . . . . . . . . . . . . . . . . . . . . .
261
Radiator expansion tank () . . . . . . . . . . . . . . . . . . . . .
Jump-start terminal (-) with hexagon head . . . . . . . . . 265, 294
267
Windscreen washer container () . . . . . . . . . . . . . . . .
225
Hydraulic fluid reservoir for power steering . . . . . . . .
document_0900452a81b1b9de.book Seite 257 Donnerstag, 26. Juli 2007 9:16 09
Checking and topping up fluids
The positions of the engine oil filler cap and the engine oil dipstick
3 and A
4 ) may be different on some
⇒ page 256, fig. 252 (items A
engine versions.
257
not be done more than once and no more than 0.5 litres should be
used.
Fixed service intervals (Inspection Service)*
If you do not take advantage of the LongLife service for your car, you
can use the oils for fixed service intervals - ⇒ page 323, “Performance, weights and dimensions”. In this case, your car must be serviced after a fixed interval of 1 year / 15,000 km (9,000 miles) – see
Service Schedule.
Engine oil
General notes
We recommend that you have the oil change carried out by an Audi
dealership / qualified workshop according to the intervals stated in
the Service Schedule or according to the service interval display in
the instrument cluster.
Whether your vehicle is serviced at flexible service intervals or fixed
service intervals is shown in the Service Schedule.
•
In exceptional circumstances, if the engine oil level is too low
⇒ page 258 and you cannot obtain the oil specified for your vehicle,
you can put in a small quantity of oil conforming to the specification
ACEA A2 or ACEA A3 (petrol engines) or ACEA B3 or ACEA B4 (diesel
engines). This should not be done more than once and no more than
0.5 litres should be used.
The correct oil specifications for your engine are listed in the Technical data section ⇒ page 323, “Performance, weights and dimensions”.
Vehicles with diesel particulate filter*
Check that the specifications quoted (VW standards) appear on the
container either singly or in combination with other specifications.
Vehicles with diesel particulate filter must only be filled with
engine oil VW 507 00. This oil can be used regardless of whether the
vehicle is serviced at flexible service intervals (Audi LongLife
Service) or fixed service intervals.
Flexible service intervals (Audi LongLife Service*)
Special engine oils ⇒ page 323, “Performance, weights and dimensions” have been developed as part of the Audi LongLife Service
(⇒ “Service Schedule”).
This type of oil must be used if you intend to take advantage of the
extended maintenance intervals allowed by the Audi LongLife
Service.
•
Do not mix the LongLife oil with oil intended for fixed service
intervals, as the requirements for the extended service intervals are
then no longer guaranteed.
The Service Schedule states whether your vehicle is fitted with a
diesel particulate filter.
•
•
•
Avoid mixing this oil with other engine oils.
In exceptional circumstances, if the engine oil level is too low
⇒ page 258 and you cannot obtain the oil specified for your vehicle,
you can put in a small quantity of oil conforming to the specification
VW 506 00 / VW 506 01 or VW 505 00 / VW 505 01 or ACEA B3 /
ACEA B4. This should not be done more than once and no more than
0.5 litres should be used.
•
In exceptional circumstances, if the engine oil level is too low
⇒ page 258 and you cannot obtain the specified LongLife oil, you
can put in a small quantity of oil for fixed service intervals ⇒ page 323, “Performance, weights and dimensions”. This should
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 258 Donnerstag, 26. Juli 2007 9:16 09
258
Checking and topping up fluids
Checking the oil level (with dipstick)
– Then pull the dipstick out again and check the oil level
⇒ fig. 253 or ⇒ fig. 254. If the oil level is too low, add
more engine oil ⇒ page 259.
a
Oil level in area A
– Do not top up oil.
Oil level in area
Fig. 253 Variant 1:
Markings on oil
dipstick
b
A
– Oil can be topped up. After topping up the oil level should
a.
be in area A
c
Oil level in area A
– Oil must be topped up. After topping up the oil level
a.
should be in area A
Fig. 254 Variant 2:
Markings on oil
dipstick
Checking the oil level
– Park your vehicle on a level surface.
– Allow the warm engine to run briefly at idling speed and
then switch off the ignition.
– Wait approx. 2 minutes.
– Pull out the dipstick. Wipe the dipstick with a clean cloth
and insert it again, pushing it in as far as it will go.
Depending on how you drive and the conditions in which the car is
used, oil consumption can be up to 0.5 ltr./1000 km. Oil consumption is likely to be higher for the first 5000 km. You should therefore
check the oil level at regular intervals, ideally every time you fill the
tank, and also before setting off on a long trip.
document_0900452a81b1b9de.book Seite 259 Donnerstag, 26. Juli 2007 9:16 09
Checking and topping up fluids
Checking the oil level (without dipstick)
the current oil level will be shown in the instrument cluster the next
time the ignition is switched on.
You can check the engine oil level via the sound system or
MMI*.
Topping up the engine oil
Applies to vehicles: without oil dipstick

Fig. 256 Engine
compartment: Engine
oil filler cap
Fig. 255 Display: Oil
level
– Select: Function selector button CAR > Oil level.
– Unscrew cap  from oil filler opening ⇒ fig. 256.
– Park your vehicle on a level surface.
– Carefully put in the specified grade of oil ⇒ page 323
0.5 litres at a time.
– Allow the warm engine to run briefly at idling speed and
then switch off the ignition.
– Wait approx. 2 minutes.
– Read off the oil level on the display ⇒ fig. 255. Top up the
engine oil if the bar in the oil level display is near the
“min” mark ⇒ page 259.
Depending on how you drive and the conditions in which the car is
used, oil consumption can be up to 0.5 ltr./1000 km. Oil consumption is likely to be higher for the first 5000 km.
259
– Check the oil level again after two minutes by calling up
the sound system or MMI* display or using the oil
dipstick ⇒ page 258.
– If the oil level is too low, add more engine oil.
– Replace the oil filler cap carefully and push the dipstick
all the way in (on vehicles with dipstick).
WARNING
•
Ensure that no oil comes into contact with hot engine components when topping up: this could cause a fire.
Note
The oil level display is intended solely for information purposes. An
oil level warning will appear in the instrument cluster if the oil level
is too low. Add more oil ⇒ page 259. If the bonnet has been opened,
Controls
Safety
Driving tips
•
Wash your skin thoroughly if it comes into contact with engine
oil.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 260 Donnerstag, 26. Juli 2007 9:16 09
260
Checking and topping up fluids
•
Caution
a ⇒ page 258, fig. 254,
The oil level must never be above area A
as this may result in damage to the catalytic converter or to the
engine. On vehicles without an oil dipstick, you can check the oil
level via the sound system or MMI*. Contact a qualified workshop to
extract the engine oil if necessary.
•
No additives should be used with engine oil. Any damage caused
by the use of such additives would not be covered by the factory
warranty.
•
•
For the sake of the environment
Never pour oil down drains or into the ground.
Always observe statutory requirements when disposing of
empty oil canisters.
Cooling system
Coolant
The purpose of the coolant is to carry heat away from the
engine. The correct amount of anti-freeze is important to
prevent the cooling system from freezing in winter.
The cooling system is filled for life at the factory, so the coolant does
not need to be changed. The coolant consists of a mixture of water
and anti-freeze additive G12++. This is a glycol-based anti-freeze
with anti-corrosion additives.
Anti-freeze additive
The amount of anti-freeze additive required depends on the temperatures to be expected in the winter season. If the anti-freeze concentration is too low the coolant can freeze, resulting in failure of the
cooling system and heater.
The cooling system is filled at the factory with the correct amount of
anti-freeze for the country concerned.
In most cases the mixture consists of 60% water and 40% additive.
This mixture gives the required anti-freeze protection at temperatures down to -25 °C and protects the alloy parts of the cooling
system against corrosion. It also prevents scaling and raises the
boiling point of the coolant.
Countries with warm climate
The coolant concentration must not be reduced by adding plain
water, even in the summer or in warm climates. The concentration
of the anti-freeze additive must always be at least 40%.
Countries with cold climate
If greater anti-freeze protection is required in very cold climates, the
proportion of the anti-freeze additive G12++ can be increased. A
concentration of 60% offers protection down to about - 40 °C. The
concentration of the anti-freeze additive must not be more than
60%, otherwise this would reduce the anti-freeze protection. In addition, the cooling effect will be adversely affected.
Vehicles for export to countries with a cold climate (such as Sweden,
Norway and Finland) are supplied with antifreeze protection down
to about -35 °C. The concentration of the antifreeze additive for
these countries should always be at least 50%.
•
Caution
It is advisable to have the cooling system checked before the
winter season to make sure that the antifreeze concentration is
adequate for the conditions to be expected. This applies particularly
if you intend to take the car into a colder climate zone. If necessary,
have the anti-freeze concentration increased to 50 - 60% as required.
•
Use only anti-freeze additive G12++, an additive meeting the
specification “TL 774 G”. Other additives may give considerably
inferior corrosion protection. The resulting corrosion in the cooling
system can lead to a loss of coolant, causing serious damage to the
engine.
document_0900452a81b1b9de.book Seite 261 Donnerstag, 26. Juli 2007 9:16 09
Checking and topping up fluids
•
The coolant additive G12++ can be mixed only with additives
G12+ and G12.
261
If there are no leaks in the system, a loss of coolant can only occur
if the coolant boils and is forced out of the system as a result of
overheating.
Checking coolant level
Caution
The coolant level can be checked at a glance.
Radiator sealants must not be added to the coolant. Such additives
could seriously impair the function of the cooling system.
Topping up the coolant
Be careful when topping up coolant.
– Switch off the engine.
Fig. 257 Engine
compartment: Markings on radiator expansion tank
– Switch off the ignition.
– Read off coolant level on radiator expansion tank
⇒ fig. 257. When the engine is cold it should be between
the “MIN” and “MAX” marks. When the engine is hot it
may be slightly above the “MAX” mark.
The coolant level should be checked with the engine switched off.
The coolant level is monitored by a warning lamp in the instrument
cluster ⇒ page 33. However, we recommend that it should be
checked occasionally.
Coolant losses
Any loss of coolant normally indicates a leak in the cooling system.
In this case the cooling system should be inspected by a qualified
workshop without delay. It is not sufficient merely to top up the
coolant.
Controls
Safety
Driving tips
– Wait for the engine to cool down.
– Cover the cap on the expansion tank ⇒ fig. 257 with a
cloth, and carefully unscrew the cap anti-clockwise
⇒
.
– Add coolant.
– Screw the cap on again tightly.
Make sure that the coolant meets the required specifications
⇒ page 260, “Coolant”. Do not use a different type of additive if antifreeze additive G12++, G12+ or G12 is not available. In this case use
only water and bring the coolant concentration back up to the
correct level as soon as possible by putting in the specified additive.
Always top up with fresh, unused coolant.
Do not fill above the “MAX” mark. Excess coolant is forced out of the
system through the valve in the filler cap when the engine gets hot.
If a lot of coolant has been lost, wait for the engine to cool down
before putting in cold coolant. Failure to do so could result in
serious engine damage.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 262 Donnerstag, 26. Juli 2007 9:16 09
262
Checking and topping up fluids
WARNING
•
The cooling system is under pressure. Do not unscrew the cap
on the expansion tank when the engine is hot: you could be
scalded by escaping steam
Brake fluid
Checking brake fluid level
The brake fluid level can be checked at a glance.
•
The coolant and coolant additive can be a health hazard. Store
the coolant additive in the original container in a safe place out of
reach of children – risk of poisoning.
For the sake of the environment
Drained off coolant should not be used again. Drain off the used
coolant into a suitable container and dispose of it in the proper
manner (observe environmental regulations).
Fig. 258 Engine
compartment: Markings on brake fluid
reservoir
Radiator fan
The radiator fan can start running spontaneously.
The radiator fan is driven by the engine via a poly V-belt. The speed
of the fan is varied by a viscous clutch according to the temperature.
There is also an auxiliary electric fan, which cuts in automatically
whenever the temperature of the coolant and the engine compartment rises above a certain level.
The auxiliary fan can continue to run for as long as 10 minutes after
stopping the engine – even after the ignition is switched off. It may
also start running suddenly ⇒
after a while if
•
•
residual heat raises the coolant temperature, or
the hot engine compartment is additionally heated up by the
sun.
WARNING
When working in the engine compartment be aware that the radiator fan may start running suddenly – risk of injury.
– Check the fluid level on the brake fluid reservoir
⇒ fig. 258. It should always be between the “MIN” and
“MAX” marks.
In right-hand drive vehicles the brake fluid reservoir is on the other
side of the engine compartment.
The fluid level may drop slightly after a period of time due to the
automatic compensation for brake pad wear. This is quite normal.
However, if the level goes down noticeably in a short time, or drops
below the “MIN” mark, there may be a leak in the brake system. If
the fluid level in the reservoir is too low, this will be indicated by the
brake warning lamp ⇒ page 32. If this should happen, take the car
to a qualified workshop immediately and have the brake system
inspected.
document_0900452a81b1b9de.book Seite 263 Donnerstag, 26. Juli 2007 9:16 09
Checking and topping up fluids
Changing brake fluid
When required, the brake fluid should be changed by a
competent mechanic with the proper equipment.
Brake fluid gradually absorbs moisture from the atmosphere. If the
water content in the brake fluid is too high, this may cause corrosion
in the brake system over time. In addition, the boiling point of the
brake fluid will be considerably reduced. This could adversely affect
the braking ability in certain circumstances.
For this reason the brake fluid must be changed periodically.
Your vehicle's Service Schedule will tell you when the brake fluid has
to be changed.
It is advisable to have the brake fluid changed as part of a regular
Inspection Service at your Audi workshop. They are familiar with the
procedure and have the necessary special tools and spare parts as
well as the proper facilities for disposing of the old fluid.
Use only the genuine brake fluid specified by the factory Qualified
workshops know that the brake fluid “DOT 4” is approved by Audi.
The brake fluid must be fresh and unused.
For the sake of the environment
If the fluid has to be drained out of the brake system, use an appropriate container to catch the used brake fluid and dispose of it in the
proper manner.
Battery
General notes
All work on batteries requires specialist knowledge.
The battery is virtually maintenance-free. It is checked as part of the
Inspection Service.
We recommend that you replace a battery once it is older than 5
years.
When an airbag is triggered, the battery will, under certain circumstances, be disconnected from the on-board power supply for
safety reasons ⇒
in “General notes on airbag system” on
page 201.
Disconnecting the battery
WARNING
•
Brake fluid is poisonous; store it in the sealed original container
in a safe place out of reach of children.
•
Heavy use of the brakes may cause a vapour lock if the brake
fluid is left in the system for too long. This would seriously affect
the efficiency of the brakes and the safety of the car – risk of accident.
Caution
Please note that brake fluid will attack the paintwork on contact.
Controls
263
Safety
Driving tips
If the battery is disconnected, some of the vehicle's functions will
become inoperative (e.g. electric windows). These functions will
require resetting after the battery is reconnected. For this reason,
the battery should only be disconnected from the vehicle's electrical
system when absolutely necessary.
If the vehicle is not used for long periods
If you do not drive your vehicle for a period of several days or weeks,
the power management will gradually shut off the on-board
systems one by one, or reduce the amount of current they are using.
This limits the amount of power consumed and helps to ensure reliable starting even after a long period ⇒ page 226.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 264 Donnerstag, 26. Juli 2007 9:16 09
264
Checking and topping up fluids
Please note that certain convenience features, such as the Audi
advanced key*, the remote control key or the electrical seat adjustment may not be available when you unlock the vehicle. These functions will be restored when you switch on the ignition and start the
engine.
Winter conditions
At low temperatures the battery has to work very hard. It also
provides only a fraction of the starting power it has at normal
temperatures.
For this reason, we recommend having the battery checked and
charged if necessary before the start of winter ⇒ page 265.
WARNING
•
All work on batteries requires specialist knowledge. For queries
regarding the vehicle battery please contact an Audi dealership or
other qualified workshop (risk of chemical burns / risk of explosion).
Important safety warnings for handling a car
battery
All work on batteries requires specialist knowledge.
The vehicle battery is located under the floor panel in the luggage
compartment.


Wear safety glasses!

Keep open flames, sparks, uncovered lights and
lit cigarettes away from battery!

A highly explosive mixture of gases is given off
when the battery is under charge!

Keep children away from the battery and battery
acid.
Battery acid is extremely corrosive. Wear protective gloves and safety glasses.
•
The battery must not be opened. Do not attempt to make any
changes to the electrolyte level of the battery. Otherwise, there is
a risk that a mixture of oxygen and hydrogen gas can accumulate
and cause an explosion.
Note
If the vehicle is to be left standing for a period of several weeks at
extremely low temperatures, the battery should be removed from
the vehicle. This ensures that it cannot “freeze up” and be
damaged.
WARNING
Always be aware of the danger of injury and chemical burns as
well as the risk of accident or fire when working on the battery and
the electrical system.
•
Wear safety glasses. Do not allow acid or lead particles to come
into contact with eyes, skin or clothing.
•
Battery acid is extremely corrosive. Wear protective gloves and
safety glasses. Do not tilt the battery - acid can leak out of the
vapour vent. If electrolyte should splash into the eyes rinse at once
for several minutes using clear water. Then seek medical care
immediately. Neutralize any acid splashes on the skin or clothing
with soap solution, and rinse off with plenty of water. If acid is
swallowed by mistake, consult a doctor immediately.
•
Keep open flames, sparks, uncovered lights and lit cigarettes
away from battery. Avoid sparks (including those from static
document_0900452a81b1b9de.book Seite 265 Donnerstag, 26. Juli 2007 9:16 09
Checking and topping up fluids
•
WARNING (continued)
charges) when handling cables and electrical equipment. Never
cross the battery poles. The resulting high-energy sparks can
cause injury.
•
A highly explosive mixture of gases is given off when the
battery is under charge. Only charge battery in a well ventilated
area.
•
•
265
Keep children away from the battery and battery acid.
Switch off all electrical equipment before starting any work on
the vehicle electrical system. Remove the ignition key. The minus
cable of the battery must be disconnected. When changing a light
bulb, it is sufficient to only turn off the light.
Do not expose the battery to direct sunlight over a long period of
time, as the intense ultraviolet radiation can affect the battery
housing.
•
If the car is left standing for long periods, protect the battery
from extreme cold temperature so that it does not “freeze up” and
become damaged.
Charging the battery
Terminals for charging the battery are fitted in the engine
compartment.
•
Before disconnecting the battery, turn off the anti-theft
system! Otherwise, the alarm will sound.
•
When disconnecting the battery from the vehicle's electrical
system, first disconnect the minus cable and then the plus cable.
•
Before reconnecting the battery, turn off all electrical equipment. First connect the plus cable, then the minus cable. The
battery cables must not be connected to the wrong battery poles
- serious risk of cable fire.
•
Never charge a frozen or thawed out battery - risk of explosion
and chemical burns! A battery must be replaced once it has been
frozen. When it is discharged the battery can freeze at temperatures around 0°C.
Fig. 259 Engine
compartment: Terminals for jump leads and
battery charger
– Note the warnings ⇒
in “Important safety warnings
for handling a car battery” on page 264 and ⇒
.
•
– Switch off all electrical equipment. Remove the ignition
key.
•
– Open the bonnet ⇒ page 254.
Make sure that the vapour hose is always attached to the
battery.
Never use a damaged battery - risk of explosion! Replace a
damaged battery immediately.
•
Caution
Never disconnect the car's battery with the engine running or
with the ignition turned on, otherwise the electrical system or electrical components will be damaged.
Controls
Safety
Driving tips
– Open the red cap on the positive terminal ⇒ fig. 259.
– Follow the correct procedure for connecting the charger
cables to the jump-start terminals (terminal with red cap
= “positive”, terminal with hexagon = “negative”).
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 266 Donnerstag, 26. Juli 2007 9:16 09
266
Checking and topping up fluids
– Now connect the battery charger to the mains and switch
on.
– After charging the battery: switch off the battery charger
and disconnect the mains cable.
– Now disconnect the charger cables.
– Refit the red cap onto the positive terminal.
– Close the bonnet ⇒ page 256.
When it is discharged the battery can freeze at temperatures
around 0°C. A frozen battery must be thawed before charging ⇒
.
However, it is advisable to replace the battery if it has frozen,
because the ice can crack the battery casing and allow the battery
acid to escape.
Charging the battery
Important: Before you charge the battery make sure you read the
manufacturer's instructions for using the battery charger.
When charging with a low current (for instance with a small battery
charger) the battery does not have to be disconnected. The battery
must not be opened while you are charging it.
Fast-charging the battery
For technical reasons it is not permissible to fast-charge the battery
using charging devices with an output voltage higher than 14.8 V.
WARNING
Replacing the battery
A replacement battery must have the same specifications
as the original equipment battery.
Your vehicle is equipped with an intelligent power management
system to control the distribution of electrical energy ⇒ page 226.
The power management function ensures that the battery is
charged much more efficiently than on vehicles without a power
management system. For this additional power to be available after
replacing the battery, we recommend that the replacement battery
used is of the same make and type as the original-equipment
battery. The battery must be encoded in the control unit for power
management. This has to be done by a qualified workshop.
A replacement battery must have the same capacity, voltage (12 V)
and current rating. It must also have the same dimensions as the
original, factory-fitted battery and have sealed caps. The battery
must comply with the standards TL 825 06 (dated December 1997 or
later) and VW 7 50 73 (August 2001 or later).
•
Caution
Make sure that the vent hose is always attached to the opening
on the side of the battery. Gases or battery acid can otherwise
escape and possibly cause damage.
•
•
The battery holder and clamps must always be correctly secured.
Before starting any work on the battery, always observe the
warnings listed under ⇒ page 264, “Important safety warnings for
handling a car battery”.
Never charge a frozen battery – it could explode.
For the sake of the environment
Note
Use only the terminals in the engine compartment to charge the
battery.
 Batteries contain toxic substances including sulphuric acid and
lead. They must be disposed of appropriately and must not be put
together with ordinary household waste. Make sure the battery
removed from the vehicle cannot tip over. Otherwise, sulphuric acid
could escape.
document_0900452a81b1b9de.book Seite 267 Donnerstag, 26. Juli 2007 9:16 09
Checking and topping up fluids
267
Windscreen washer
Plain water on its own is not sufficient for the windscreen
washer system.
Fig. 260 Engine
compartment: Windscreen washer
container
The container for the windscreen washer  contains the cleaning
fluid for the windscreen and the headlight washer system*
⇒ fig. 260. Container capacity: ⇒ page 321.
Plain water on its own is not enough to clean the glass properly. It
is therefore advisable to add a suitable washer fluid additive (with
wax solvent) to the water. A washer fluid with freeze-resistant additive should be used in winter.
•
•
Caution
Never put in radiator anti-freeze or other additives.
Never use washer fluid which contains paint thinners or solvents
as it can damage the paintwork.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 268 Donnerstag, 26. Juli 2007 9:16 09
268
Wheels and tyres
Wheels and tyres
Wheels
General notes
– When driving with new tyres, be especially careful during
the first 500 km.
– If you have to drive over a kerb or similar obstacle, drive
very slowly and as near as possible at a right angle to the
kerb.
– Inspect the tyres regularly for damage (cuts, cracks or
blisters, etc.). Remove any foreign bodies embedded in
the treads.
Concealed damage
Damage to tyres and rims is often not readily visible. If you notice
unusual vibration or the car pulling to one side, this may indicate
that one of the tyres is damaged. Reduce speed immediately if there
is any reason to suspect that damage may have occurred. Inspect
the tyres for damage. If no external damage is visible, drive slowly
and carefully to the nearest qualified workshop and have the car
inspected.
Tyres with directional tread pattern
An arrow on the tyre sidewall indicates the direction of rotation on
tyres with directional tread. Always note the direction of rotation
indicated when mounting the wheel. This guarantees optimum grip
and helps to avoid aquaplaning, excessive noise and wear.
– Damaged wheels and tyres must be replaced immediately.
Tyre service life
– Keep grease, oil and fuel off the tyres.
Correct inflation pressures and sensible driving habits
will increase the service life of your tyres.
– Replace any missing valve caps as soon as possible.
– Mark the wheels before taking them off so that they
rotate in the same direction when put back.
– When removed, the wheels or tyres should be stored in a
cool, dry and preferably dark place.
New tyres
New tyres do not give maximum grip straight away and should
therefore be “run in” by driving carefully and at moderate speeds for
about the first 500 km. This will also help to make the tyres last
longer.
The tread depth of new tyres may vary, according to the type and
make of tyre and the tread pattern.
Fig. 261 Open driver's
door (LHD vehicle) with
sticker listing tyre
inflation pressures
– Check the tyre pressures at least once a month.
document_0900452a81b1b9de.book Seite 269 Donnerstag, 26. Juli 2007 9:16 09
Wheels and tyres
– The tyre pressures should only be checked when the
tyres are cold. The slightly raised pressures of warm tyres
must not be reduced.
– The pressures must be altered to suit major changes in
the load being carried.
Wheel balancing
The wheels on new vehicles are balanced. However, various factors
encountered in normal driving can cause them to become unbalanced, which results in steering vibration.
– Avoid fast cornering and hard acceleration.
Unbalanced wheels should be rebalanced, as they otherwise cause
excessive wear on steering, suspension and tyres. A wheel must
also be rebalanced when a new tyre is fitted or if a tyre is repaired.
– Inspect the tyres for irregular wear from time to time.
Incorrect wheel alignment
Tyre pressure and vehicle loading
The tyre pressure must be adjusted according to the load the vehicle
is carrying. We recommend adhering to the tyre pressure specifications for a maximum load. The tyre inflation pressures are listed on
a sticker on the end face of the driver's door ⇒ page 268, fig. 261.
However, if you prefer an extra-smooth ride and the vehicle is not
fully loaded, you can select the tyre pressure for a normal load (no
more than three people travelling in the vehicle). However, should
you wish to drive with a full load you must increase the tyre pressure
to the specified maximum.
Under-inflation or over-inflation will reduce the life of the tyres
considerably and also impair the car's handling. Correct inflation
pressures are very important, especially at high speeds. The pressures should therefore be checked at least once a month and before
starting a journey.
269
Incorrect wheel alignment causes excessive tyre wear, impairing the
safety of the vehicle. If you notice excessive tyre wear, contact your
Audi dealer.
WARNING
•
Always adapt the tyre pressure accordingly when the vehicle
load changes.
•
Under-inflated tyres flex more and can overheat at continuous
high speeds. This can cause tread separation and tyre blow-out,
which could result in an accident.
For the sake of the environment
Under-inflated tyres will increase the fuel consumption.
Do not forget the spare wheel* when checking the tyre pressures.
Keep the spare tyre inflated to the highest pressure required for the
road wheels.
Driving habits
Fast cornering, heavy acceleration and hard braking (squealing
tyres) all increase tyre wear.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 270 Donnerstag, 26. Juli 2007 9:16 09
270
Wheels and tyres
Tread wear indicators
WARNING (continued)
The tread wear indicators show the condition of the tyre
treads.
aquaplaning in deep puddles of water and when driving through
corners. Braking is also adversely affected.
•
The speed has to be adapted accordingly, otherwise there is a
risk of losing control over the vehicle.
Changing wheels round
Fig. 262 Tyre tread:
Tread wear indicators
The original tyres on your vehicle have 1.6 mm high “tread wear
indicators” ⇒ fig. 262 running across the tread. Depending on the
make, there will be 6 to 8 of them spaced at equal distances around
the tyre. Markings on the tyre sidewall (for instance the letters “TWI”
or a triangle) indicate the positions of the tread wear indicators.
The minimum tread depth required by law in Germany is 1.6 mm
(measured in the tread grooves next to the tread wear indicators).
Other specifications may apply in export countries.
WARNING
Fig. 263 Changing
wheels round
To ensure that the wear is equal on all tyres the wheels should be
changed round from time to time according to the system
⇒ fig. 263. All the tyres will then last for about the same time.
Replacing wheels and tyres
To avoid putting safety at risk, the tyres must be replaced at the
latest when the tread is worn down to the tread wear indicators.
It is important to use the correct wheels and tyres when
replacement is necessary.
Especially in difficult driving conditions such as wet or icy
roads, it is important that the tyres have sufficient tread depth.
The tread depth should same on the tyres of both the front and the
rear axles.
– All four wheels must be fitted with tyres of the same type,
size (rolling circumference) and preferably the same
tread pattern.
•
• The decrease in driving safety due to insufficient tread depth is
particularly evident in vehicle handling, when there is a risk of
– If possible, tyres should be replaced at least in pairs and
not individually (i.e. both front tyres or both rear tyres
together).
document_0900452a81b1b9de.book Seite 271 Donnerstag, 26. Juli 2007 9:16 09
Wheels and tyres
– Never use tyres whose actual size exceeds the dimensions of the factory-approved makes of tyre.
means, for example, that the tyre was produced in the 10th week of
2006.
– If you wish to fit the vehicle with non-standard rims or
tyres, it is advisable to consult an Audi dealer before
purchasing them.
Please note that with some types of tyres, the actual tyre size can
differ from the nominal size marked on the tyre (for instance 225/50
R 17 94 Y), and there may be significant differences in the contours
of the tyres, even though the tyres are marked with the same
nominal size designation. When replacing the tyres, it is therefore
important to make sure that the actual size of the new tyres does
not exceed the dimensions of the factory-approved makes of tyre.
The tyres and wheel rims are an essential part of the vehicle's
design. The tyres and rims approved by Audi are specially matched
to the characteristics of the vehicle and make a major contribution
to good roadholding and safe handling ⇒
.
The sizes of the rims and tyres approved for your vehicle are listed
in the vehicle's documents (e.g. EC Certificate of Conformity or COC
document 3) ). The vehicle documents vary depending on the
country of residence.
Understanding the tyre designations makes it easier to choose the
correct tyres. For example, radial ply tyres have the following tyre
designations marked on the sidewall:
225 / 50 R 17 94 Y
This contains the following information:
225
Tyre width in mm
50
Height/width ratio in %
R
Tyre construction: Radial
17
Rim diameter in inches
94
Load rating code
Y
Speed rating code letter
Failure to observe this requirement can affect the clearance needed
for the tyres. This could result in contact between the tyres and
suspension components or bodywork. The brake lines could also be
damaged and the vehicle's safety could be severely impaired ⇒
.
When using tyres with the maximum permitted nominal dimensions, this can also void the vehicle's registration.
If you use tyres that are approved by Audi you can be sure that the
actual tyre dimensions will be correct for your vehicle. If you decide
to fit a different type of tyre, you must obtain the appropriate manufacturer's certificate from the tyre retailer to confirm that the tyres
are suitable for your vehicle. Keep this certificate in a safe place.
Your local Audi dealer will be able to advise you on which tyres may
be fitted to your vehicle.
On vehicles with four-wheel drive, all four tyres must always be
fitted with tyres of the same type, make and tread pattern, as otherwise the driveline can be damaged by continuous variations in the
wheel speeds. For the same reason, only use a spare wheel* with
the same tyre dimensions as the normal road wheels.
The manufacturing date is also indicated on the tyre sidewall
(possibly only on the inner side of the wheel):
DOT ... 1006...
3)
271
It the spare tyre* is not the same type as the tyres fitted on the car
(for example if the car has winter tyres or wide-section tyres) you
should only use the spare tyre if a puncture occurs, and then only
for a short period of time. In this case, please drive with extra care.
Refit the normal road wheel as soon as possible.
It is best to have all servicing of wheels and tyres performed by a
qualified workshop. They have the necessary special tools and
COC = certificate of conformity
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 272 Donnerstag, 26. Juli 2007 9:16 09
272
Wheels and tyres
replacement parts, trained personnel and facilities for disposing of
the old tyres.
WARNING
•
It is very important to ensure that the tyres you have chosen
have adequate clearance. When selecting replacement tyres, do
not rely entirely on the nominal tyre size marked on the tyre; with
some makes of tyre the effective tyre size can differ significantly
from the nominal dimensions, even though the tyres have the
same size designation. Inadequate tyre clearance can result in
damage to the tyres or the vehicle, causing a serious safety risk. It
may also invalidate the vehicle's type approval for use on public
roads.
•
Wheel bolts
The wheel bolts are designed to suit the rims on your car.
The wheel bolts are matched to the rims. When installing different
wheels (for instance wheels with winter tyres) it is important to use
the correct wheel bolts with the right length and correctly shaped
bolt heads. This is essential for the secure fit of the wheels and for
the proper function of the brake system.
Audi dealers have full information on the technical requirements
when installing or changing tyres, rims or wheel trims.
The wheel bolts should be clean and turn easily.
A special adapter is required to turn the anti-theft wheel bolts*
⇒ page 292.
Please ask your Audi dealer or qualified workshop whether run
flat tyres can be used on your vehicle. Unauthorised use of these
tyres can invalidate the vehicle's type approval for use on public
roads. Furthermore, this could cause damage to your vehicle and
possibly also result in an accident.
Winter tyres
Avoid running the car on tyres that are more than 6 years old.
If you have no alternative, you should drive slowly and with extra
care at all times.
– Use only radial ply winter tyres.
•
Winter tyres will significantly improve the car's handling
in winter road conditions.
– Winter tyres must be fitted on all four wheels.
For the sake of the environment
Old tyres must be disposed of according to the laws in the country
concerned.
•
Note
Never mount used tyres if you are not sure of their previous
history.
•
For technical reasons it is not normally possible to use wheel
rims from other vehicles. In some cases this also applies to rims
from other vehicles of the same model.
– Only use winter tyres of the correct type approved for
your vehicle.
– Please note that the maximum permissible speed for
winter tyres may be lower than for summer tyres.
– Also note that winter tyres are no longer effective when
the tread is worn down.
– After fitting the wheels you must always check the tyre
pressures. The correct tyre pressures are listed on the
sticker on the end face of the driver's door.
document_0900452a81b1b9de.book Seite 273 Donnerstag, 26. Juli 2007 9:16 09
Wheels and tyres
In winter road conditions winter tyres will considerably improve the
car's handling. Due to their type of construction (width, rubber
compound, tread pattern), summer tyres give less grip on ice and
snow. This applies particularly to vehicles equipped with wide
section tyres or high speed tyres (code letters H, V or Y on the sidewall).
Only use winter tyres of the correct type approved for your vehicle.
The sizes of the winter tyres approved for your vehicle are listed in
the vehicle's documents (e.g. EC Certificate of Conformity or COC
document 4) ). The vehicle documents vary depending on the
country of residence. Also refer to ⇒ page 270, ⇒ page 270.
Winter tyres are no longer fully effective when the tread is worn
down to a depth of 4 mm.
The performance of winter tyres is also severely impaired by ageing,
even if the tread is still much deeper than 4 mm.
Winter tyres are subject to the following maximum speed limits
according to speed rating code letter: ⇒
Speed rating code letter
⇒ page 270, ⇒ page 270
Maximum speed limit
Q
160 km/h
S
180 km/h
T
190 km/h
H
210 km/h
V
240 km/h
(note restrictions)
Using winter tyres with V-rating
Please note that the generally applicable 240 km/h speed rating for
winter tyres with the letter "V" is subject to technical restrictions;
the maximum permissible speed for your vehicle may be significantly lower. The maximum speed limit for tyres with a V-rating
depends directly on the maximum axle weights for your car and on
the listed weight rating of the tyres being used.
It is best to contact an Audi dealer to check the maximum speed
which is permissible for the V-rated tyres fitted on your car on the
basis of this information.
WARNING
Exceeding the maximum speed permitted for the winter tyres
fitted on your car can cause tyre failure, resulting in a loss of
control of the vehicle – risk of accident.
For the sake of the environment
Snow chains
Snow chains will improve the vehicle's handling on snowcovered roads.
– Snow chains can be used on the front wheels only.
– Keep your speed below 50 km/h.
Snow chains will improve braking ability as well as traction in winter
conditions.
COC = certificate of conformity
Controls
“All-weather” tyres can also be used instead of winter tyres.
Summer tyres should be fitted again as soon as possible; they give
better handling on roads which are free of snow and ice. Summer
tyres produce less rolling noise, do not wear down as quickly and,
most importantly, reduce fuel consumption.
In Germany vehicles capable of exceeding these speeds must have
an appropriate sticker attached so it is visible to the driver. Suitable
stickers are available from Audi dealers and specialist retailers.
Please note regulations to this effect in your country.
4)
273
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 274 Donnerstag, 26. Juli 2007 9:16 09
274
Wheels and tyres
For technical reasons snow chains may only be used on tyres with
certain wheel rim/tyre combinations.
Rim size
Rim offset
Tyre size
7Jx16
39 mm
205/60
7Jx16
46 mm
225/55
7Jx17
46 mm
225/50
Only use snow chains with fine-pitch links. The links must not
protrude more than 13.5 mm from the tyres (including tensioner).
Remove the chains when roads are free of snow. Otherwise they will
impair handling, damage the tyres and wear out very quickly.
Four-wheel drive: where snow chains are compulsory on certain
roads, this normally also applies to cars with four-wheel drive. Snow
chains may only be fitted to the front wheels (also on vehicles with
four-wheel drive).
Run flat tyres
Applies to vehicles: with run flat tyres
Introduction
If you change the tyres on your vehicle from regular tyres to run flat
tyres or vice-versa, the control unit must be reprogrammed by an
Audi dealer or other qualified workshop.
What are the benefits of run flat tyres?
Run flat tyres ensure that you remain mobile, even in the event of a
loss of tyre pressure. In favourable conditions these tyres have an
operating range of at least 30 km, however the vehicle must not be
driven faster than 80 km/h ⇒
in “Driving with run flat tyres” on
page 275.
The tyre pressures are constantly checked by the tyre pressure
monitoring system. When the run flat system becomes active
(centre display), it is still the driver's responsibility to check the
tyre(s) affected and to decide whether it is possible to continue
driving. Also refer to ⇒ page 275, “Driving with run flat tyres”.
When is it no longer possible to continue driving with
the help of the run flat tyres?
•
If the Electronic Stabilisation Program (ESP) is out of operation
or is triggered continuously.
•
•
If one of the tyres has been severely damaged in an accident, etc.
If a tyre has been badly damaged there is a risk that parts of the
tread can be thrown off and cause damage to the fuel lines, brake
pipes or fuel filler.
Run flat tyres allow you to continue your journey in the
event of a loss of tyre pressure.
•
Run flat tyres have reinforced sidewalls which support the tyre in
the event of a loss of pressure.
•
Run flat tyres must only be used on vehicles which were already
factory-fitted with these tyres and which also have a tyre pressure
monitoring system*.
Run flat tyres can be identified by the marking “RSC” (Runflat
System Component) on the sidewall.
If the tyre pressure monitoring system is out of operation.
You must stop driving if severe vibrations occur, or if the wheel
starts overheating and gives off smoke.
You must also stop driving if damage to the tyres (e.g. tears in
the sidewalls) becomes apparent.
WARNING
Please ask your Audi dealer or qualified workshop whether run flat
tyres can be used on your vehicle. Unauthorised use of these tyres
can invalidate the vehicle's type approval for use on public roads.
document_0900452a81b1b9de.book Seite 275 Donnerstag, 26. Juli 2007 9:16 09
Wheels and tyres
Please refer to ⇒ page 274, “When is it no longer possible to
continue driving with the help of the run flat tyres?”
WARNING (continued)
Furthermore, this could cause damage to your vehicle and
possibly also result in an accident.
•
Effects on handling when driving with defective tyres
If one of the front tyres is defective, your vehicle will tend to pull
slightly towards that side and braking performance will be
impaired.
Note
If you cannot continue driving even with run flat tyres please
obtain professional assistance.
•
You should obtain professional assistance if you are in any doubt
regarding the rims and tyres for your vehicle.
A defective rear tyre will also make the vehicle pull slightly to one
side, and the braking response will again be slightly impaired.
These effects will be most noticeable when driving in a corner.
WARNING
Applies to vehicles: with run flat tyres
Driving with run flat tyres
•
Please remember that the vehicle's handling will be
impaired.
•
Driving a vehicle with a deflated tyre, or with insufficient
tyre pressure, is an abnormal situation. However, since the
handling of a vehicle equipped with run flat tyres is only
slightly impaired, it is important to remember that you are
driving with a deflated tyre. If you have to make use of the
run flat system please remember the following points:
– The Electronic Stabilisation Program (ESP) must be
switched on.
– Do not exceed 80 km/h ⇒
275
When using the run flat system the changes in vehicle handling
will be noticeable when braking, in corners and during fast acceleration.
The maximum permitted speed of 80 km/h is subject to road
and weather conditions. Always observe the relevant rules and
regulations. Run flat tyres allow you to continue your journey in
the event of a loss of tyre pressure. However, the driver remains
responsible for the safety of the vehicle and for restoring the
correct tyre pressure and having defective parts replaced
⇒ page 276. For these reasons you should always adjust your
driving to suit the circumstances.
Caution
We recommend that you drive with great care when making use of
the run flat system. Avoid abrupt manoeuvres.
.
– Anticipate the traffic situation well in advance.
– Be careful when accelerating.
– Avoid unnecessary braking and steering manoeuvres.
– Reduce speed in good time before corners and potential
hazards.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 276 Donnerstag, 26. Juli 2007 9:16 09
276
Wheels and tyres
Applies to vehicles: with run flat tyres
Renewing defective components on run flat
tyres
The run flat tyres have been specially developed for your
vehicle and matched to its requirements.
Use and combine only the approved run flat tyres and rims. It is not
permissible to combine standard wheels and run flat tyres ⇒
.
If you have to drive with low tyre pressure or with a completely
deflated tyre, you should always take the vehicle to an authorised
qualified workshop and have the defective parts inspected and the
condition corrected.
WARNING
•
We recommend that you have the run flat tyre renewed and
also have the rim checked by a qualified workshop to identify any
damage.
•
Using tyres or rims which have not been approved can cause
damage to the vehicle. Vehicle handling can be impaired and
driving safety can no longer be guaranteed. This can also void the
vehicle's certification for use on public roads.
Note
Run-flat tyres can be repaired with the TMS ⇒ page 285.
document_0900452a81b1b9de.book Seite 277 Donnerstag, 26. Juli 2007 9:16 09
Accessories and modifications to the vehicle
277
Accessories and modifications to the vehicle
Accessories and replacement parts
Always ask your dealer or specialist retailer for advice
before purchasing accessories and replacement parts.
Your car is designed to offer a high standard of active and passive
safety. For this reason, we recommend that you ask an Audi dealer
for advice before fitting accessories or replacement parts. Audi
dealers have the latest information from the manufacturer and can
recommend accessories and replacement parts which are suitable
for your requirements. They can also answer any questions you
might have regarding official regulations.
We recommend you to use only Audi accessories and Audi Genuine
parts®. Audi has tested these parts and accessories for suitability,
reliability and safety. Audi dealers have the necessary experience
and facilities to ensure that the parts are installed properly.
Although the market is constantly scrutinised, Audi cannot judge or
assume responsibility for the reliability, safety and suitability of
non-genuine products - even though in some instances, these parts
may have been approved by an officially recognised technical
testing authority or accompanied by an official approval certificate.
Any retro-fitted equipment which has a direct effect on the vehicle
and/or the way it is driven (e.g. cruise control system or electronically-controlled suspension) must be approved for use in your
vehicle and bear the e mark (the European Union's approval
symbol).
If any additional electrical components are fitted which do not serve
to control the vehicle itself (for instance a refrigerator box, laptop or
ventilator fan, etc.), these must bear the CE mark (manufacturer
conformity declaration in the European Union).
Controls
Safety
Driving tips
WARNING
Never attach accessories (such as cup holders or telephone
brackets) to the surfaces covering the airbag units or the areas
around the airbags: this could cause injury if the airbag is
triggered.
Modifications
Modifications must always be carried out according to
our specifications.
Unauthorised modifications to the electronic components or software in the vehicle may cause malfunctioning. Due to the way the
electronic components are linked together in networks, other
systems may be affected by the faults. This can seriously impair
safety, lead to excessive wear of components, and also invalidate
the type approval for your vehicle.
You will appreciate that your Audi dealer cannot be held liable for
any damage caused by modifications and/or work performed incorrectly.
We recommend that all work should be performed by an Audi workshop using Audi Genuine parts ®.
WARNING
Incorrectly performed modifications or other work on your vehicle
can lead to malfunctions and cause accidents.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 278 Donnerstag, 26. Juli 2007 9:16 09
278
Accessories and modifications to the vehicle
Radio transmitters and business
equipment
driver's immediate control of the vehicle. Any such equipment must
carry the CE mark. Any retrofit equipment that could influence the
driver's control of the vehicle must have a type approval for your
vehicle and must carry the e mark.
Radio transmitters (fixed installation)
Retrofit installations of radio transmitters in the vehicle are subject
to official approval. Audi generally authorises in-vehicle installations of approved types of radio transmitters provided that:
•
•
the aerial is installed correctly,
the aerial is not installed in the interior of the vehicle (and
screened cables are used together with non-reflective aerial trimming),
WARNING
Mobile telephones or radio equipment which are operated inside
the vehicle without a correctly installed external aerial can create
excessive magnetic fields that could cause a health hazard.
•
•
Audi dealers and specialist retailers will be able to inform you about
options for installing and operating radio transmitters with a higher
transmitting power.
•
the effective transmitting power does not exceed 10 Watts at the
aerial base.
Mobile radio transmitters
When using commercial mobile telephones or radio equipment it is
possible that they might interfere with the electronics of your
vehicle and cause malfunctions. The reasons could be:
•
•
•
no external aerial
external aerial incorrectly installed
transmitting power more than 10 W.
Therefore you must not operate portable mobile telephones or radio
equipment inside the vehicle without a correctly installed external
aerial ⇒
.
Please note also that the maximum range of the equipment can only
be achieved with an external aerial.
Business equipment
Retrofit installation of business or other equipment in the vehicle is
permitted, provided the equipment cannot interfere with the
Note
Any retrofit installation of electrical or electronic equipment in
the vehicle will affect its type approval. In extreme cases this could
mean that you might lose the type approval for your vehicle.
Please refer to the mobile telephone/radio operating
instructions.
document_0900452a81b1b9de.book Seite 279 Donnerstag, 26. Juli 2007 9:16 09
Accessories and modifications to the vehicle
Controls
Safety
Driving tips
General maintenance
Self-help
279
Technical data
document_0900452a81b1b9de.book Seite 280 Donnerstag, 26. Juli 2007 9:16 09
280
document_0900452a81b1b9de.book Seite 281 Donnerstag, 26. Juli 2007 9:16 09
Self-help
281
document_0900452a81b1b9de.book Seite 282 Donnerstag, 26. Juli 2007 9:16 09
282
Self-help
Self-help
Applies to vehicles: with warning triangle
Applies to vehicles: with first-aid kit
Warning triangle
First-aid kit
The factory-supplied warning triangle is attached to the
inside of the boot lid.
The first-aid kit is accommodated in the compartment
behind the rear centre armrest.
Fig. 264 Warning
triangle fitted inside
boot lid
– To remove the warning triangle, push the tab in the direction indicated by the arrow ⇒ fig. 264 and pull the
retainer down.
The retainer on the boot lid is specifically designed to hold the
warning triangle supplied as an Audi Genuine Accessory. This
accessory is available from Audi dealers.
Fig. 265 Rear centre
armrest: First-aid kit
– Pull up the catch to open the storage compartment
⇒ fig. 265.
On vehicles with a load-through hatch*, the first-aid kit is kept in the
rear centre armrest. The centre armrest has to be folded down in
order to access the compartment.
The storage compartment will hold a maximum weight of 0.5 kg.
Note
Before folding the centre armrest back up into the rear seat backrest
make sure the lid of the storage compartment is properly closed.
document_0900452a81b1b9de.book Seite 283 Donnerstag, 26. Juli 2007 9:16 09
Self-help
Fire extinguisher
Have the fire extinguisher checked regularly (at least every two
years) by a qualified dealer or by the fire service to ensure that it will
be in working order when you need it.
The factory-fitted fire extinguisher is located in the footwell on the front passenger's side (secured in a holder).
When buying a new fire extinguisher, make sure it fits in the holder.
Applies to vehicles: with fire extinguisher
283
WARNING
If the fire extinguisher is not secured properly it could be catapulted through the vehicle during driving and braking manoeuvres
or in the event of an accident. This poses a risk of injury to occupants.
Fig. 266 Fire extinguisher in footwell on
front passenger's side
•
•
Note
The fire extinguisher must comply with legal requirements.
Taking out the fire extinguisher
Observe the expiry date of the fire extinguisher. The fire extinguisher may not work properly after the expiry date.
– Unfasten the retaining strap by pressing on the tab
marked “PRESS” ⇒ fig. 266 -arrow-.
Tools and Tyre Mobility System
– Take the fire extinguisher out of the holder.
The tools and the Tyre Mobility System are stored under
the floor panel in the luggage compartment.
Securing the fire extinguisher
– Place the fire extinguisher in the holder.
– Secure the fire extinguisher with the retaining strap.
After using the fire extinguisher
– Have the fire extinguisher refilled and checked by a qualified dealer or the fire service.
Fig. 267 Luggage
compartment: Tools,
Tyre Mobility System
and jack
Check how the fire extinguisher works before you need to use it. The
instructions for use are shown on the fire extinguisher.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 284 Donnerstag, 26. Juli 2007 9:16 09
284
Self-help
If you need the tools, the Tyre Mobility System or the jack*, you will
have to open the floor panel and take out the spare wheel*
⇒ page 284.
The tool kit includes:
•
•
•
•
•
•
•
•
•
•
A hook for removing hub caps
Applies to vehicles: with compact temporary spare wheel
Compact temporary spare wheel*
The spare wheel is carried in the wheel well under the
floor panel in the luggage compartment. It is only
intended for temporary use over short distances.
Pin for mounting a wheel
Screwdriver with reversible blade
Tool for changing bulbs
Interchangeable socket (Torx socket for changing bulbs)
Crank handle for jack
Adapter for anti-theft wheel bolts*
Jack*
Box spanner for wheel bolts
Fig. 268 Spare wheel
Towline anchorage
Some of the parts listed are only fitted on certain models or are
optional extras.
Before stowing the jack* again, wind down the arm of the jack as far
as it will go.
WARNING
•
Do not use the hexagonal socket in the screwdriver handle to
tighten the wheel bolts. It is not possible to tighten the bolts with
the required torque – risk of accident.
•
Taking out the spare wheel
– Lift the floor panel by the plastic handle ⇒ fig. 268.
– Hook the handle onto the luggage compartment weatherstrip.
– Turn the centre plastic knob ⇒ fig. 268 anti-clockwise.
– Take out the spare wheel.
– Unhook the floor panel before closing the boot lid.
The jack supplied by the factory is only designed for changing
wheels on this model. On no account attempt to use it for lifting
heavier vehicles or other loads – risk of injury.
Securing the defective wheel in the spare wheel
well
Never start the engine when the vehicle is on the jack - risk of
accident.
– Place the wheel in the spare wheel well and secure it with
the plastic knob.
•
•
If work has to be done under the vehicle, ensure that it is safely
supported on stands designed for the purpose, otherwise there is
a risk of injury.
– Unhook the floor panel before closing the boot lid.
document_0900452a81b1b9de.book Seite 285 Donnerstag, 26. Juli 2007 9:16 09
Self-help
How to use the compact temporary spare wheel
Tyre repairs
Should you ever have a punctured tyre, the compact temporary
spare wheel is only intended for temporary use until you can reach
a workshop. The standard-size road wheel should be refitted as
soon as possible.
General information and safety notes
285
Repaired tyres are only suitable for temporary use.
Please note the following restrictions when using the compact
temporary spare wheel. The compact temporary spare wheel is
designed specifically for this model. For this reason, do not use a
temporary spare from a different type of vehicle.
Snow chains
For technical reasons, snow chains must not be used on the
compact temporary spare wheel.
If you should have a puncture on one of the front wheels when using
snow chains, fit the compact temporary spare in place of one of the
rear wheels. You can then attach the snow chains to the wheel taken
from the rear and use this wheel to replace the punctured front
wheel.
WARNING
•
The tyre pressures must be checked and corrected as soon as
possible. The tyre pressure of the compact temporary spare wheel
must be 4.2 bar – an incorrectly inflated tyre can cause an accident.
•
Fig. 269 The Tyre
Mobility System is NOT
suitable for repairing
this type of damage to
tyres.
Your vehicle is equipped with a tyre repair kit: the Tyre Mobility
System (TMS).
In the event of a puncture you will find the TMS, which consists of a
sealing compound and an electric compressor, located under the
floor panel in the luggage compartment.
The TMS will reliably seal tyres damaged by foreign bodies,
provided that the cuts or punctures are no larger than approx. 4 mm
in diameter.
Do not drive faster than 80 km/h - higher speeds can cause an
accident.
It is not necessary to remove the foreign body from the tyre.
Avoid heavy acceleration, hard braking and fast cornering – risk
of accident.
•
•
•
•
•
Never use two or more compact spare tyres at the same time –
risk of accident.
•
No other type of tyre (normal summer or winter tyres) may be
fitted on the compact temporary spare wheel.
Controls
Safety
Driving tips
The sealing compound must not be used:
1
on cuts and punctures larger than 4 mm ⇒ fig. 269 A
if the wheel rim has been damaged
2
A
if you have been driving with very low pressure or a completely
3 .
flat tyre A
How to use the TMS is described in the section Repairing a tyre
⇒ page 286 and in the instructions supplied with the tyre sealant
can.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 286 Donnerstag, 26. Juli 2007 9:16 09
286
Self-help
The TMS can be used at outside temperatures down to – 20 °C.
For the sake of the environment
WARNING
Used bottles of sealing compound can be returned to an Audi dealer
for disposal.
After repairing a tyre please note the following points:
•
•
•
•
Do not drive faster than 80 km/h.
Avoid heavy acceleration, hard braking and fast cornering.
Vehicle handling could be impaired.
Tyres which have been sealed using the TMS are only suitable
for temporary use. Damaged tyres must be renewed.
•
•
Note
If sealant should leak out, leave it to dry. When it has dried, you
can pull it off like a piece of foil.
•
Observe the expiry date stated on the sealing compound can.
Have the sealing compound exchanged by a qualified workshop.
The TMS must NOT be used,
− on cuts and punctures larger than 4 mm
Repairing a tyre
− if the wheel rim has been damaged
•
− if you have been driving with very low pressure or a
completely flat tyre
Seek professional assistance if the repair of a tyre puncture is
not possible with the sealing compound.
•
Do not allow the sealant to come into contact with your eyes,
skin or clothing.
•
If you do come into contact with the sealant immediately rinse
the eyes or skin affected with clean water.
Fig. 270 Repairing a
tyre
•
Change clothing immediately if it becomes soiled with the tyre
sealant.
•
•
Make sure you do not breathe in the fumes!
If any of the tyre sealant is accidentally ingested, immediately
rinse the mouth thoroughly and drink lots of water.
•
•
Do not induce vomiting. Immediately contact a doctor!
If any allergic reactions should occur get medical help immediately.
•
Keep the sealant away from children.
Preparations
– If you have a flat tyre, stop the car well away from moving
traffic.
– Apply the parking brake to stop the vehicle moving accidentally.
– Engage first gear (manual gearbox) or move selector
lever to position P (automatic gearbox).
document_0900452a81b1b9de.book Seite 287 Donnerstag, 26. Juli 2007 9:16 09
Self-help
– Check whether a repair is possible using the Tyre
Mobility System ⇒ page 285.
Inflating the tyre
– Ensure that all passengers leave the vehicle and move
away from the danger area ⇒
.
– Screw the filling hose of the electric compressor onto the
tyre valve and plug the connector into the cigarette
lighter.
– Take the tyre sealant can and the electric compressor out
of the luggage compartment ⇒ page 283.
– Pump the tyre up to 2.0 to 2.5 bar and monitor the pressure shown on the pressure gauge.
– Fix the sticker “max. 80 km/h”, which is included with the
tyre sealant can, onto the instrument cluster where the
driver will see it.
– If the tyre pressure remains lower than the value specified above drive the vehicle approx. 10 metres forwards
or backwards, so that the sealant can spread evenly in
the tyre. If the pressure is still lower than the specification the tyre is too badly damaged and cannot be
repaired using the tyre sealant.
Filling the tyre
– Shake the tyre sealant can well.
– Screw the enclosed filling hose onto the sealant can as
far as it will go. This will automatically pierce the foil
sealing the can.
– Take the valve cap off the tyre valve and use the enclosed
valve insert tool to unscrew the valve insert ⇒ page 286,
fig. 270.
287
Final checks
– After about 10 minutes stop to check the tyre pressure.
– If tyre pressure is less than 1.3 bar, the tyre is too badly
damaged. Do not drive on. You should obtain professional assistance.
– Place the valve insert onto a clean surface.
WARNING
– Remove the sealing plug from the filling hose and insert
the hose into the tyre valve.
•
– Hold the tyre sealant can upside down and fill the
complete contents of the can into the tyre.
•
– Then disconnect the hose and screw the valve insert
firmly back into the tyre valve.
•
If you have a puncture in moving traffic, switch on the hazard
warning lights and place the warning triangle in a visible location.
This is for your own safety and also warns other road users.
Make sure your passengers wait in a safe place (for instance
behind the roadside crash barrier).
Please observe the manufacturers' safety notes on the
compressor and the instructions supplied with the tyre sealant
can.
•
If it was not possible to build up a tyre pressure of 2.0 bar
within 6 minutes this means that the tyre is too badly damaged.
Do not drive on.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 288 Donnerstag, 26. Juli 2007 9:16 09
288
Self-help
•
– All passengers should leave the car. They should wait in
a safe place (for instance behind the roadside crash
barrier).
•
– Apply the parking brake to stop the vehicle moving accidentally.
WARNING (continued)
Seek professional assistance if the repair of a tyre puncture is
not possible with the sealing compound.
If tyre pressure is less than 1.3 bar after driving about 10
minutes, the tyre is too badly damaged. Do not drive on. You
should obtain professional assistance.
Caution
Take special care if you have to repair a tyre on a gradient.
•
Note
Do not use the compressor for longer than 6 minutes at a time,
as it could overheat. When the compressor has cooled down, you
can use it again.
•
If tyre sealant should leak out, leave it to dry and then pull it off
like foil.
•
After carrying out a tyre repair remember to buy a new tyre
sealant can at a qualified workshop. This will ensure that the Tyre
Mobility System is operative again.
•
Please observe the relevant regulations.
Changing a wheel
Preparations
Some preparations are necessary before changing a
wheel.
– If you have a flat tyre, stop the car well away from moving
traffic. Choose a location that is as level as possible.
– Engage first gear (manual gearbox) or move selector
lever to position P (automatic gearbox).
– When towing a trailer: unhitch the trailer from your
vehicle.
– Take the tools ⇒ page 283 and the spare wheel*
⇒ page 284 out of the luggage compartment.
WARNING
If you have a puncture in moving traffic, switch on the hazard
warning lights and place the warning triangle in a visible location.
This is for your own safety and also warns other road users.
Caution
If you have to change the tyre on a gradient, block the wheel opposite the wheel being changed by placing a stone or similar object
under it to prevent the vehicle from rolling away.
Note
Please observe the relevant regulations.
How to change a wheel
Change the wheel as described below.
– Pull off the hub cap. Also refer to ⇒ page 289, “Hub
caps”.
document_0900452a81b1b9de.book Seite 289 Donnerstag, 26. Juli 2007 9:16 09
Self-help
– Loosen the wheel bolts ⇒ page 289.
Hub caps
– Raise the car with the jack* ⇒ page 290.
The hub caps must be removed for access to the wheel
bolts.
– Take off the wheel with the flat tyre and then put on the
spare wheel* ⇒ page 291.
289
– Lower the vehicle to the ground.
– Tighten the wheel bolts firmly in diagonal sequence with
the box spanner ⇒ page 289.
– Fit the hub cap back on.
Fig. 271 Changing a
wheel: Removing a hub
cap
After changing a wheel
What you must do after changing a wheel.
– Place the wheel with the defective tyre in the spare wheel
well and secure it.
Removing
– Insert the hook (provided in the vehicle's tool kit) in the
hole in the hub cap.
– Put the tools and the jack* back in the luggage compartment.
– Pull off the hub cap ⇒ fig. 271.
– The inflation pressure of the newly fitted spare tyre must
be checked as soon as possible.
Loosening and tightening the wheel bolts
– Have the tightening torque of the wheel bolts checked as
soon as possible with a torque wrench. The correct tightening torque is 120 Nm.
The wheel bolts must be loosened before raising the
vehicle.
– Have the flat tyre replaced as quickly as possible.
•
Note
If you notice that the wheel bolts are corroded and difficult to
turn when changing a wheel, they must be replaced before having
the tightening torque checked.
Fig. 272 Changing a
wheel: Loosening
wheel bolts
•
In the interest of safety, drive at moderate speeds until the tightening torque of the wheel bolts has been checked.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 290 Donnerstag, 26. Juli 2007 9:16 09
290
Self-help
Loosening
Raising the vehicle
– Fit the box spanner as far as it will go over the wheel
bolt5) .
The vehicle must be raised with the jack* to remove the
wheel.
– Grip the box spanner as close to the end as possible and
turn the wheel bolts about one turn anti-clockwise
⇒ page 289, fig. 272 -arrow-.
Tightening
– Fit the box spanner as far as it will go over the wheel
bolt5) .
– Grip the box spanner as close to the end as possible and
tighten the bolt firmly by turning clockwise.
Fig. 273 Changing a
wheel: Jacking points
WARNING
To avoid accidents, the wheel bolts should only be loosened
slightly (about one turn) before raising the vehicle with the jack*.
•
Note
Do not use the hexagonal socket in the screwdriver handle to
loosen or tighten the wheel bolts.
Fig. 274 Changing a
wheel: Jack
•
If the wheel bolt is very tight, it may be possible to loosen it by
pushing down the end of the spanner carefully with your foot. Hold
on to the car for support and take care not to slip.
Each jacking point is marked by a recess underneath the
vehicle ⇒ fig. 273.
–
5)
An adapter is required to unscrew or tighten the anti-theft wheel bolts*
⇒ page 292.
Place the jack ⇒ page 283 underneath the jacking point
closest to the wheel being changed. Make sure the base
A is flat on the ground.
plate A
B until the claw of the jack
– Wind up the jack by the knob A
C completely surrounds the seam on your vehicle
A
⇒ fig. 274.
document_0900452a81b1b9de.book Seite 291 Donnerstag, 26. Juli 2007 9:16 09
Self-help
D onto the jack by inserting it
– Now fit the crank handle A
in the opening on the knob ⇒ page 290, fig. 274. Turn the
crank handle clockwise or anti-clockwise to secure it in
place.
291
Taking off the wheel and putting on the spare
wheel
Step-by-step instructions for taking off the wheel and
putting on the spare wheel.
– Raise the vehicle by winding the crank handle until the
defective wheel is clear of the ground.
Recesses at the front and rear of the door sills mark the jacking
points ⇒ page 290, fig. 273. There is one jacking point for each
wheel. The distance from the jacking points to the wheel arches is
approximately 20 cm at the front and 40 cm at the rear. The jack may
only be applied at the seam of the jacking points shown.
Fig. 275 Changing a
wheel: Hexagonal
socket in screwdriver
handle to turn the
wheel bolts after they
have been loosened
An unstable surface under the jack may cause the vehicle to slip off
the jack. Always provide a firm base for the jack on the ground. If
necessary use a large, strong board or similar support. On a hard,
slippery surface (such as tiles) use a rubber mat or similar to prevent
the jack from slipping.
WARNING
•
•
Prevent the base of the jack from slipping – risk of injury.
The car can be damaged if the jack is not applied at the correct
jacking points. There is also a risk of injury since the jack can slip
off suddenly if it is not properly engaged.
Fig. 276 Changing a
wheel: Mounting pin in
wheel bolt hole nearest
to the top
Change the wheel as described below after loosening the
wheel bolts and raising the vehicle with the jack*.
Taking off the wheel
– Using the hexagonal socket in the screwdriver handle
(provided in the vehicle's tool kit) ⇒ fig. 275, unscrew the
wheel bolt nearest to the top and place the bolt on a
clean surface.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 292 Donnerstag, 26. Juli 2007 9:16 09
292
Self-help
– Screw in the mounting pin (provided in the vehicle's tool
kit) by hand in place of the wheel bolt ⇒ page 291,
fig. 276.
– Then unscrew the other wheel bolts as described above.
– Take off the wheel. The mounting pin stays where it is.
Putting on the spare wheel
– Put on the spare wheel, using the mounting pin to guide
it into place.
– Screw in the wheel bolts and tighten them lightly using
the hexagonal opening in the screwdriver handle.
– Then unscrew the mounting pin and tighten the
remaining wheel bolt lightly.
Tyres with directional tread pattern
Tyres with directional tread pattern must be mounted so
that they rotate in the correct direction.
A directional tread pattern is identified by arrows on the sidewall
pointing in the forward running direction. Always note the direction
of rotation indicated when mounting the wheel. This is important so
that these tyres can give maximum grip and avoid excessive noise,
tread wear and aquaplaning.
Drive carefully should you ever have a puncture and have to mount
the spare wheel so it rotates in the wrong direction. This is because
the tyre will not give optimum performance. Bear this in mind
particularly when driving on wet roads.
To benefit from the advantages of tyres with this type of tread
pattern, the defective tyre should be replaced and refitted as soon
as possible so that all tyres again rotate in the correct direction.
– Carry out the steps required after you have changed the
wheel ⇒ page 289, “After changing a wheel”.
Applies to vehicles: with anti-theft wheel bolts
The wheel bolts should be clean and turn easily. Before putting on
the spare wheel, inspect the condition of the wheel and hub
mounting surfaces. These surfaces must be clean before mounting
the wheel.
Anti-theft wheel bolts
A special adapter is required to turn the anti-theft wheel
bolts.
The wheel bolts are easier to remove from the wheel rim if you use
the hexagonal socket in the screwdriver handle. The reversible
screwdriver blade should be removed as a precautionary measure
when the tool is used for this purpose.
Note the direction of rotation when putting on a tyre with directional tread pattern ⇒ page 292.
Note
Do not use the hexagonal socket in the screwdriver handle to loosen
or tighten the wheel bolts.
Fig. 277 Anti-theft
wheel bolt with
adapter
document_0900452a81b1b9de.book Seite 293 Donnerstag, 26. Juli 2007 9:16 09
Self-help
– Insert the hook (provided in the vehicle's tool kit) in the
hole in the hub cap.
– Pull off the hub cap ⇒ page 289, fig. 271.
2 completely into the wheel bolt A
1 .
A
2 .
Fit the box spanner as far as it will go over the adapter A
– Insert the adapter
–
293
Jump leads
The jump leads must be heavy enough to carry the starter current.
Refer to the details given by the manufacturer.
Only use jump leads with insulated battery clamps.
Positive cable – usually red
Negative cable – usually black
– Loosen or tighten the wheel bolt ⇒ page 289.
WARNING
It is advisable to carry the wheel bolt adapter in the vehicle. The
adapter is normally stored in the vehicle tool kit, underneath the
towline anchorage. It should be put back there after use.
•
The code number of the anti-theft wheel bolt is stamped on the front
of the adapter. Your Audi dealer will need this number to replace the
adapter if lost.
•
Note
Note the code number of the anti-theft wheel bolt and keep it in a
safe place – not in your vehicle.
When it is discharged the battery can freeze at temperatures
around 0°C. A frozen battery must first be thawed out before
connecting the jump leads, as it could otherwise explode.
Please note the safety warnings referring to working in the
engine compartment ⇒ page 255.
•
Note
There must be no contact between the two vehicles as otherwise
current could flow as soon as the positive terminals are connected.
•
The discharged battery must be properly connected to the
vehicle's electrical system.
Jump-starting
•
Switch off the car telephone if necessary. Details will be given in
the manufacturer's instructions for the car telephone.
Before starting the engine
If necessary, the engine can be started by connecting it to
the battery of another vehicle.
If the engine should ever fail to start because of a discharged
battery, the battery can be connected to the battery of another
vehicle to start the engine. Suitable jump leads are required.
Both batteries must be rated at 12 Volts. The capacity (Ah) of the
booster battery should not be significantly lower than that of the
discharged battery.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 294 Donnerstag, 26. Juli 2007 9:16 09
294
Self-help
Starting the engine
The two jump leads must be connected in the correct
sequence.
2. Connect the other end of the positive lead to the positive
2 of the boosting battery A
B .
terminal A
Connecting negative terminals with the
negative lead (black)
3. Connect one end of the negative lead to the negative
3 of the boosting battery A
B .
terminal A
4. Connect the other end of the lead to the jump-start
4 (terminal with hexagon = “negative”) of the
terminal A
A .
vehicle with the flat battery A
Fig. 278 Engine
compartment: Terminals for jump leads and
battery charger
Starting the engine
– Start the engine of the vehicle with the boosting battery
B and let it run at idling speed.
A
– Now start the engine of the vehicle with the discharged
A .
battery A
Fig. 279 Jumpstarting with the
battery of another
vehicle: A – Discharged
battery, B – Boosting
battery
– If the engine fails to start: do not operate the starter for
longer than 10 seconds. Wait for about 30 seconds and
try again.
– When the engine is running, disconnect the leads in
exactly the opposite sequence to that described above.
– Refit the red cap onto the positive terminal.
The jump-start terminals are located in the engine compartment ⇒ fig. 278.
Connecting the positive terminals with the
positive lead (red)
The battery is vented to the outside to prevent gases entering the
vehicle's interior.
Connect the battery clamps so they have good metal-to-metal
contact with the respective terminals.
– Open the red cap on the positive terminal ⇒ fig. 278.
1. Connect one end of the lead to the jump-start terminal
1 (terminal under red cap = “positive”) of the
⇒ fig. 279 A
A .
vehicle with the flat battery A
WARNING
•
The non-insulated parts of the battery clamps must not be
allowed to touch. The jump lead attached to the positive battery
document_0900452a81b1b9de.book Seite 295 Donnerstag, 26. Juli 2007 9:16 09
Self-help
WARNING (continued)
terminal must not touch metal parts of the vehicle: this can cause
short circuiting.
•
•
•
– Engage the clutch very gently when starting to move; on
vehicles with automatic gearbox press the accelerator
slowly.
Do not bend over the batteries – risk of acid burns.
Notes for the driver of the towed vehicle
The screw plugs on the battery cells must be screwed in firmly.
– The ignition should be switched on so that the turn
signals, horn, windscreen wipers and washers can be
used. Please ensure that the steering wheel is unlocked
when you switch on the ignition, and that it moves freely.
Keep sparks, flame and lighted cigarettes away from batteries:
the gases given off can cause an explosion.
•
If jump-starting another vehicle, position the jump leads in
such a way that they cannot come into contact with any moving
parts in the engine compartment of the other vehicle.
Caution
Please note that the above method of connecting the leads is meant
for jump-starting your vehicle. If jump-starting another vehicle, you
should not connect the negative lead (–) to the negative terminal of
the discharged battery, but directly to the engine block or a solid
metal part bolted to the engine block. If the battery of the other
vehicle does not have a gas vent, there is a risk that a mixture of
oxygen and hydrogen gas can accumulate and cause an
explosion.
Tow-starting and towing away
– Put gear lever in neutral (manual gearbox) or move
selector lever to position N (automatic gearbox).
– The brake servo and power steering only work when the
engine is running. Considerably more effort is required
on the brake pedal and steering wheel when the engine
is switched off.
– Ensure that the towrope remains taut at all times when
towing.
Towrope or towbar
It is easier and safer to tow a vehicle with a towbar. You should only
use a towrope if you do not have a towbar.
A towrope should be slightly elastic to reduce the loading on both
vehicles. It is advisable to use a towrope made of synthetic fibre or
similar material.
General notes
Points to observe when tow-starting or towing away
If you use a towrope:
Attach the tow-rope or tow-bar only to the towing anchorages
intended for this purpose ⇒ page 296 or ⇒ page 297.
Driving technique
Notes for the driver of the towing vehicle
– The towrope must be taut before driving off.
Controls
295
Safety
Driving tips
Towing requires some experience – especially when using a
towrope. Both drivers should be familiar with the technique required
for towing. Inexperienced drivers should not attempt to tow-start or
tow away another vehicle.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 296 Donnerstag, 26. Juli 2007 9:16 09
296
Self-help
Do not pull too hard with the towing vehicle and take care to avoid
jerking the towrope. When towing on a loose surface there is always
a risk of overloading and damaging the anchorage points.
Caution
If there is no oil in the gearbox or no lubricant in the automatic
transmission the car may only be towed with the driven wheels
lifted clear of the road, or transported on a special car transporter
or trailer.
•
•
Fig. 281 Front
bumper: Fitting the
towing eye
The screw connection for the towline anchorage is located
behind a cover cap on the right side of the front bumper.
Note
Note the regulations concerning towing.
The hazard warning lights of both vehicles must normally be
switched on. However, observe any regulations to the contrary.
– Take the towline anchorage out of the vehicle's tool kit
⇒ page 283.
Make sure that the towrope is not twisted, as otherwise the front
towline anchorage on your vehicle could work itself loose.
– To detach the cover cap from the bumper, firmly press
the lower part of the cap inwards to release it ⇒ fig. 280.
Front towline anchorage
– Screw the towline anchorage firmly all the way into the
screw connection ⇒ fig. 281.
•
The front towline anchorage is only mounted if the vehicle
has to be towed.
After use, unscrew the towline anchorage and put it back in the
toolbox. Replace the cap in the bumper. The towline anchorage
should always be kept in the vehicle.
WARNING
If the towline anchorage is not screwed in as far as the stop, there
is a risk of the screw connection shearing off during towing (accident risk).
Fig. 280 Front
bumper: Cover cap
document_0900452a81b1b9de.book Seite 297 Donnerstag, 26. Juli 2007 9:16 09
Self-help
Rear towline anchorage
Vehicles which do not have a factory-fitted towing
bracket* have a towline anchorage on the right side of the
rear bumper.
297
WARNING
•
If the towline anchorage is not screwed in as far as the stop,
there is a risk of the screw connection shearing off during towing
(accident risk).
•
If your car has a towing bracket*, please use only special tow
bars with suitable attachments (i.e. tow bars which are specially
designed for use with towing brackets) to avoid damage to the
coupling equipment.
•
If your car has a towing bracket*, please use only special
towing ropes (risk of accident).
Fig. 282 Rear bumper:
Fitting the towing eye
Tow-starting
As a general rule, tow-starting is not recommended.
Vehicles with towline anchorage
– Engage 2nd or 3rd gear before moving off.
– Take the towline anchorage out of the vehicle's tool kit.
– Press the clutch and hold the pedal down.
– To detach the cover cap from the bumper, firmly press
the lower part of the cap inwards to release it ⇒ fig. 282.
– Switch on the ignition.
– Screw the towline anchorage firmly all the way into the
screw connection.
Vehicles with towing bracket*
– Fit the towing bracket.
– Attach the towbar or the towrope to the towing bracket.
After use, unscrew the towline anchorage and put it back in the
toolbox. Replace the cap in the screw connection. The towline
anchorage or towing bracket should always be kept in the vehicle.
Vehicles which have a factory-fitted towing bracket* do not have a
screw connection at the rear for the towline anchorage.
Controls
Safety
Driving tips
– Once both vehicles are moving, release the clutch.
– As soon as the engine starts: press the clutch and put the
gear lever in neutral.
If the engine will not start, it is best to try starting it using the
battery of another vehicle ⇒ page 293 before attempting to tow
start. You should only try to tow-start the engine if jump-starting is
not successful. Tow-starting is an attempt to start the engine via the
movement of the wheels.
When tow-starting a vehicle with a petrol engine, do not tow it more
than a short distance, otherwise unburnt fuel can enter the catalytic
converter and cause damage.
For technical reasons, it is not possible to tow-start a vehicle with
automatic gearbox.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 298 Donnerstag, 26. Juli 2007 9:16 09
298
Self-help
WARNING
There is a high risk of accidents when tow-starting, as the towed
vehicle can easily be driven into the towing vehicle.
Caution
When tow-starting the vehicle, do not tow it further than 50 metres:
otherwise the catalytic converter could be damaged.
Towing a vehicle with manual gearbox and
front-wheel drive
Towing is relatively straightforward.
Please observe the notes ⇒ page 295.
The vehicle can be towed using a towbar or towrope in the normal
way, with all four wheels on the road; it can also be towed with
either the front or rear wheels lifted off the road. The vehicle must
not be towed faster than 50 km/h.
Towing a vehicle with automatic gearbox and
front-wheel drive
Certain restrictions must be observed when towing your
vehicle.
Please observe the notes ⇒ page 295.
The vehicle can be towed with a towbar or towrope in the normal
way, with all four wheels on the ground. When doing so, please note
the following points:
•
•
•
Release the parking brake ⇒ page 121.
Make sure the selector lever is in the N position.
The vehicle must not be towed faster than 50 km/h.
•
The vehicle must not be towed further than 50 km. The reason
for this is: when the engine is not running, the gearbox oil pump
does not work and the gearbox is not adequately lubricated for
higher speeds or longer distances.
If the vehicle has to be towed with a breakdown truck, it must only
be suspended at the front wheels. The reason for this is: the drive
shafts are located on the front wheels. If the car is towed with the
rear wheels lifted off the road (i.e. travelling backwards), the drive
shafts also turn backwards. The planetary gears in the automatic
gearbox then turn at such high speeds that the gearbox will be
severely damaged in a short time.
Note
If it is not possible to tow the vehicle as described above, or if it has
to be towed further than 50 km, it must be transported on a special
car transporter or trailer.
Towing a vehicle with manual gearbox and
four-wheel drive
Certain restrictions must be observed when towing your
vehicle.
Please observe the notes ⇒ page 295.
The vehicle can be towed with a towbar or towrope in the normal
way, with all four wheels on the ground. It can also be towed by a
breakdown truck, with the wheels lifted at either the front or rear.
When doing so, please note the following points:
•
•
The vehicle must not be towed faster than 50 km/h.
The vehicle must not be towed further than 50 km.
document_0900452a81b1b9de.book Seite 299 Donnerstag, 26. Juli 2007 9:16 09
Self-help
299
Note
If it is not possible to tow the vehicle as described above, or if it has
to be towed further than 50 km, it must be transported on a special
car transporter or trailer.
Towing a vehicle with automatic gearbox and
four-wheel drive
Certain restrictions must be observed when towing your
vehicle.
Please observe the notes ⇒ page 295.
The vehicle can be towed with a towbar or towrope in the normal
way, with all four wheels on the ground. When doing so, please note
the following points:
•
•
•
•
Release the parking brake ⇒ page 121.
Make sure the selector lever is in the N position.
The vehicle must not be towed faster than 50 km/h.
The vehicle must not be towed further than 50 km. The reason
for this is: when the engine is not running, the gearbox oil pump
does not work and the gearbox is not adequately lubricated for
higher speeds or longer distances.
The vehicle must not be towed with the wheels lifted at either the
front or rear.
Note
If it is not possible to tow the vehicle as described above, or if it has
to be towed further than 50 km, it must be transported on a special
car transporter or trailer.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 300 Donnerstag, 26. Juli 2007 9:16 09
300
Fuses and bulbs
Fuses and bulbs
Fuses
Caution
Never attempt to “repair” a fuse or replace it by fitting a fuse with a
higher rating - risk of fire! It could also cause damage to other parts
of the electrical system.
Changing a fuse
If a fuse has blown it must be replaced.
Note
If a newly replaced fuse blows again after a short time, the electrical
system must be checked by a qualified workshop as soon as
possible.
Fuses on the driver's side
Fig. 283 Left side of
dash panel: Fuse cover
– Identify the fuse for the failed component.
– Switch off the ignition and the component concerned.
– Remove the fuse box cover ⇒ fig. 283.
– Take the plastic clip from inside the fuse cover, fit it onto
the blown fuse, and pull the fuse out.
– Replace the blown fuse (which will have a melted metal
strip) with a new fuse of the same amp rating.
The various electrical circuits are protected by fuses. The fuse boxes
are located behind covers on the left and right sides of the dash
panel and in the compartment on the right side of the boot.
A plastic clip for removing the fuses is provided in the fuse cover on
the left side of the dash panel. There is also a sticker listing the fuses
in each of the fuse boxes in the dash panel.
Fig. 284 Diagram of
fuse box (left-hand
drive vehicle)
Some of the items listed are only fitted on certain models or are
optional extras.
Please note that the following list, while correct at the time of
printing, is subject to alterations. If discrepancies should occur,
please refer to the sticker on the inside of the fuse cover for the
correct information for your vehicle.
document_0900452a81b1b9de.book Seite 301 Donnerstag, 26. Juli 2007 9:16 09
Fuses and bulbs
The seats with electrical adjustment are protected by circuit
breakers. These reset automatically after a few seconds when the
overload has been corrected.
Fuse list
No.
Electrical equipment
amps
Fuse carrier (black)
No.
Electrical equipment
amps
5
Seat heating (left-side) with/without seat ventilation
30
6
Electronic stabilisation program
10
7
Horn
25
8
Electric window motor (left door)
30
1
Dynamic steering
5
9
Wiper motor
30
2
Clutch sensor
5
10
Electronic stabilisation program
25
3
Garage door opener
5
11
Door control unit (driver's side)
15
4
Audi lane assist
10
12
Rain and light sensor
5
5
Air conditioner
5
6
Headlight range control (right)
5
7
Headlight range control (left)
5
Fuse list
No.
Electrical equipment
amps
Fuse carrier (red)
8
Control unit 1 for vehicle's electrical system
5
9
Interior mirrors
5
1
Vacant
10
Selector gate
5
2
Vacant
Lumbar support
10
35
11
Heated washer jets
5
3
12
Air conditioner
5
4
Dynamic steering
5
Interior light
5
6
Control unit 1 for vehicle's electrical system
35
Fuse list
No.
Electrical equipment
amps
7
Control unit 1 for vehicle's electrical system
30
Fuse carrier (brown)
8
Control unit 1 for vehicle's electrical system
30
1
Vacant
9
Tilting panorama roof/sun roof
20
2
Clutch sensor
5
10
Control unit 1 for vehicle's electrical system
30
3
Fuel pump (diesel/petrol)
20/25
11
Vacant
4
Auxiliary water pump (3.2 FSI)
5
12
Convenience electronics
Controls
Safety
Driving tips
301
General maintenance
5
Self-help
Technical data
document_0900452a81b1b9de.book Seite 302 Donnerstag, 26. Juli 2007 9:16 09
302
Fuses and bulbs
Fuses on the passenger's side
No.
Fig. 285 Diagram of
fuse box (left-hand
drive vehicle)
Some of the items listed are only fitted on certain models or are
optional extras.
Electrical equipment
amps
7
Diagnostic connector
5
8
Gateway (diagnostic interface for data bus)
5
9
Vacant
10
Vacant
11
Vacant
12
Vacant
Fuse list
No.
Electrical equipment
amps
Fuse carrier (brown)
Please note that the following list, while correct at the time of
printing, is subject to alterations. If discrepancies should occur,
please refer to the sticker on the inside of the fuse cover for the
correct information for your vehicle.
1
CD drive
2
Switch module for Audi drive select
3
MMI/Radio
The seats with electrical adjustment are protected by circuit
breakers. These reset automatically after a few seconds when the
overload has been corrected.
4
Light switch
5
5
Control unit for instrument cluster
5
6
Ignition lock
5
Fuse list
7
Vacant
8
Air conditioner blower
40
9
Steering column lock
5
No.
Electrical equipment
amps
Fuse carrier (black)
5
5
10/20
1
Vacant
10
Air conditioner
10
2
Vacant
11
Diagnostic connector
10
3
Vacant
12
Steering column switch module
5
4
Vacant
5
Steering column switch module
5
6
Electronic Stabilisation Program
5
document_0900452a81b1b9de.book Seite 303 Donnerstag, 26. Juli 2007 9:16 09
Fuses and bulbs
Fuse list for luggage compartment
No.
Electrical equipment
303
amps
10
Control unit 2 for vehicle's electrical system
30
11
Control unit 2 for vehicle's electrical system
20
12
Vacant
Fuse list
No.
Fig. 286 Diagram of
fuse panel
Electrical equipment
amps
Fuse carrier (brown)
1
Electrical socket
2
Vacant
3
Radio/navigation
7.5
4
Control unit for digital sound system
30
5
MMI
5
6
Door control unit (driver's side)
30
Fuse carrier (black)
7
Electro-mechanical parking brake
30
Vacant
8
Seat heating, rear
30
2
Control unit for trailer
15
9
Door control unit (passenger side)
30
3
Control unit for trailer
20
10
Remote control receiver for auxiliary heating
5
Door control unit (passenger side)
15
Control unit for reversing camera
5
– Remove the trim.
– Open the fuse cover.
Fuse list
No.
1
Electrical equipment
amps
4
Control unit for trailer
20
11
5
Electronic parking brake
5
12
6
Electronic suspension control
15
7
Electro-mechanical parking brake
30
8
Control unit 2 for vehicle's electrical system
30
9
Vacant
Controls
Safety
Driving tips
15
Fuse list
No.
Electrical equipment
amps
Fuse carrier (red)
1
Socket, centre console, rear
15
2
Socket, centre console, front
15
3
Socket, luggage compartment
15
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 304 Donnerstag, 26. Juli 2007 9:16 09
304
Fuses and bulbs
No.
Electrical equipment
amps
4
Cigarette lighter
15
5
Parking aid
5
6
Phone pre-installation without handsfree system (VDA interface)
5
7
Control unit for adaptive cruise control
15
8
Vacant
9
EPB switch (electro-mechanical parking brake)
5
10
Lane change assist feature
5
11
Seat heating, rear
5
12
Airbag
5
•
•
Xenon headlights*: Bulb for turn signals
Xenon headlights*: Light source for daytime running
lights/parking lights
•
•
•
Bulb for headlights: Bi-xenon lights ⇒
Light source for turn signal in exterior mirror housing
Light source for high-level brake light
As a rule, you require a certain degree of practical skill to change
defective bulbs. This applies in particular to those bulbs which are
only accessible from the engine compartment.
If in doubt, we recommend that you have defective bulbs changed
by a qualified workshop or qualified mechanic.
If you do decide to change bulbs in the engine compartment yourself, be aware of the safety risks involved ⇒ page 255 ⇒
.
Types of bulbs
Bulbs
Changing bulbs
You must only replace a bulb with a bulb of the same type. Information regarding e.g. the wattage can be found on the base of the
bulb.
Changing bulbs requires a certain degree of practical
skill.
Dipped-beam headlights (halogen)
55 W (H7)
You can change the following bulbs for exterior lights yourself:
Main beam headlights (halogen)
55 W (H7)
Front fog lights
55 W (H7)
•
•
•
•
•
•
Halogen headlights: Bulb for dipped headlights
Version
Halogen headlights: Bulb for main beam headlights
Bulb for fog light
Bulbs for rear lights in boot lid
Bulbs for rear lights in side panel
Bulbs for number plate light
The following bulbs should only be changed by a qualified workshop:
•
•
Front bulb (12 V)
Halogen headlights: Bulb for turn signals
Halogen headlights: Bulb for side lights
Rear bulb (12 V)
Brake lights / tail lights
Version
P 21 W
Turn signals (rear)
P 21 W
Reversing lights
W 16 W
Rear fog light
H 21 W
Number plate lights
5W
document_0900452a81b1b9de.book Seite 305 Donnerstag, 26. Juli 2007 9:16 09
Fuses and bulbs
305
•
Before changing a bulb, make sure you have the correct new
bulb.
WARNING
•
•
Bulbs are sensitive to pressure. The glass can break when you
touch the bulb, causing injury.
Do not touch the glass part of the bulb with your bare hands, use
a cloth or paper towel instead. Otherwise, the fingerprints left on
the glass will vaporise as a result of the heat generated by the bulb,
be deposited on the reflector and impair its surface.
Incorrect handling of the high-voltage element of xenon gasdischarge bulbs* can have potentially fatal consequences.
Bulbs with a bayonet fastener
When changing bulbs, please take care not to injure yourself on
sharp edges, in particular on the headlight housing.
Bulbs with a bayonet fastener must be changed as follows:
Take particular care when working on components in the
engine compartment if the engine is warm - risk of burns!
•
•
•
•
Removing the bulb
Caution
Always remove the ignition key before carrying out any work on
the electrical system - danger of short circuiting!
•
•
•
Switch off the lights or parking lights before you change a bulb.
Take good care to avoid damaging any components.
Removing the lights in particular can lead to the paintwork
becoming damaged. This is another reason why we recommend
having the bulbs changed by a qualified workshop.
For the sake of the environment
Please ask your specialist retailer how to dispose of used bulbs in
the proper manner.
– Lightly press the defective bulb into the bulb holder, then
turn it anti-clockwise and remove it.
– Do not touch the glass part of the new bulb with your
bare hands, use a cloth or paper towel instead.
Fitting the bulb
– Fit the new bulb, pressing it into the bulb holder, and turn
it clockwise as far as it will go.
– If necessary, use a cloth to remove any fingerprints from
the glass part of the bulb.
Note
Place the parts you have removed on a soft cloth so that they do not
become scratched.
•
Please check at regular intervals that all lighting (especially the
exterior lighting) on your vehicle is functioning properly. This is not
only in the interest of your own safety, but also in that of all other
road users.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 306 Donnerstag, 26. Juli 2007 9:16 09
306
Fuses and bulbs
Bulb holders with a bayonet fastener
Changing bulbs for headlights
Removing and installing headlights
Fig. 288 Trim panel:
Attachment points are
marked by arrows
Fig. 287 Diagram: Bulb
holder with a bayonet
fastener
In the case of bulb holders with a bayonet fastener please
proceed as follows:
Removing the bulb holder
A
– Turn the bulb holder in the direction of the arrow A
⇒ fig. 287 as far as it will go and then take the bulb
holder out of the light unit.
Fig. 289 Headlight
unit: Attachment
points are marked by
arrows
Fitting the bulb holder
– Insert the bulb holder into the light unit, making sure you
keep the bulb holder straight, i.e. the rubber seal makes
even contact all around.
The description for removing the headlight refers to the left
headlight; in principle the same procedure applies to the
right headlight.
– Turn the bulb holder in the direction indicated by the
B ⇒ fig. 287 as far as it will go.
arrow A
Removing
– Switch off the ignition and the lights.
– Open the bonnet.
document_0900452a81b1b9de.book Seite 307 Donnerstag, 26. Juli 2007 9:16 09
Fuses and bulbs
– Take the screwdriver and the interchangeable Torx socket
out of the vehicle tool kit.
307
Removing bulb for main beam headlights
– Remove the screws ⇒ page 306, fig. 288 that secure the
trim panel to the lock carrier and detach the trim panel.
– Slacken the two screws that secure the headlight to the
lock carrier and the two screws at the underside of the
headlight (the screws at the underside should not be
slackened more than five turns) ⇒ page 306, fig. 289.
Fig. 290 Headlight
unit: Rubber cap is
highlighted
– Carefully pull the headlight forward about 60 mm.
– Release and unplug the electrical connector.
– Carefully take the headlight out towards the front (swivel
it slightly if necessary).
Installing
– Perform all of the above steps in reverse sequence.
The headlight must be inserted in two guides (on the underside of
the headlight). This is the only way to ensure that the headlight is
installed in the correct position. To determine whether the headlight
is correctly installed, check that it is aligned flush with adjacent
body parts (such as the wing panel).
Do not interchange the securing screws.
Fig. 291 Bulb holder
for main beam headlights
– Remove the headlight ⇒ page 306.
– Take off the rubber cap ⇒ fig. 290 ⇒
bulbs” on page 304.
Caution
Please take particular care not to damage or scratch the adjacent
parts of the body when removing or installing the headlights.
in “Changing
– Press the connector in the direction of the arrow
⇒ fig. 291.
–
Remove the connector together with the bulb from the
headlight housing.
– Disconnect the connector from the base of the bulb
⇒
in “Changing bulbs” on page 304.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 308 Donnerstag, 26. Juli 2007 9:16 09
308
Fuses and bulbs
Installing the bulb for the main beam
headlights
– Press the connector in the direction of the arrow
⇒ fig. 293 until the bulb engages.
When installing a bulb, the lug on the base of the bulb
must be inserted into the appropriate mounting on the
bulb housing.
– Check that the bulb is securely seated in the bulb
housing.
– Fit the rubber cap and install the headlight ⇒ page 306.
– Check whether the new bulb is working.
– Have the headlight settings checked.
Note
Fig. 292 Bulb with
connector: The lug on
the base of the bulb is
highlighted
Fig. 293 Fitting bulb
for main beam headlights
– Attach the new bulb to the connector ⇒
bulbs” on page 304.
in “Changing
– Insert the bulb carefully into the bulb housing. Start by
placing the base of the bulb directly behind one of the
retaining hooks so that the lug fits into the recess on the
bulb housing.
Ensure that the rubber cap is seated correctly so that no water can
enter the unit.
Removing bulb for dipped headlights
Fig. 294 Headlight
unit: Cover
document_0900452a81b1b9de.book Seite 309 Donnerstag, 26. Juli 2007 9:16 09
Fuses and bulbs
309
Installing bulb for dipped headlights
When installing a bulb, the lug on the base of the bulb
must be inserted into the appropriate mounting on the
bulb housing.
Fig. 295 Bulb holder
for dipped headlights
– Remove the headlight ⇒ page 306.
– Take off the cover ⇒ page 308, fig. 294 ⇒
“Changing bulbs” on page 304.
Fig. 296 Bulb with
connector: The lug on
the base of the bulb is
highlighted
in
– Press the connector in the direction of the arrow
⇒ fig. 295.
– Remove the connector together with the bulb from the
headlight housing.
– Disconnect the connector from the base of the bulb
⇒
in “Changing bulbs” on page 304.
Fig. 297 Inserting bulb
for dipped headlights
– Attach the new bulb to the connector ⇒
bulbs” on page 304.
in “Changing
– Insert the bulb carefully into the bulb housing. Start by
placing the base of the bulb directly behind one of the
retaining hooks so that the lug fits into the recess on the
bulb housing.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 310 Donnerstag, 26. Juli 2007 9:16 09
310
Fuses and bulbs
– Press the connector in the direction of the arrow
⇒ page 309, fig. 297 until the bulb engages.
– Check that the bulb is securely seated in the bulb
housing.
– Fit the cover.
– Install the headlight ⇒ page 306.
Fig. 299 Screws
securing fog light
– Check whether the new bulb is working.
– Have the headlight settings checked.
Changing bulb for front fog lights
The description for changing the bulb refers to the right fog
light; in principle the same procedure applies to the left fog
light.
– Switch off the ignition and the lights.
Applies to vehicles: with halogen main beam headlights
– Detach the trim cover ⇒ fig. 298 (pull it carefully in the
direction of the arrow).
Preparations
– Remove the two securing screws ⇒ fig. 299 and pull the
fog light unit out of the bumper.
– Unplug the electrical connector.
Caution
Fig. 298 Trim cover for
fog light
The trim cover is secured to the bumper by several retaining hooks.
Do not use force when removing the trim cover to avoid damaging
it.
document_0900452a81b1b9de.book Seite 311 Donnerstag, 26. Juli 2007 9:16 09
Fuses and bulbs
311
Changing bulbs for rear lights in side
panel
Applies to vehicles: with halogen main beam headlights
Changing bulb
Overview of rear lights
Fig. 300 Front fog
light: Bulb holder is
highlighted
– Turn the bulb holder anti-clockwise ⇒ page 306 and take
it out of the fog light housing.
Fig. 301 Rear lights in
side panel
– Insert the new bulb holder and turn it clockwise as far as
the stop ⇒ page 306.
•
•
After changing the bulb re-install all parts in the reverse sequence
and check that the bulb is working.
The following instructions for changing the bulb refer to the left side
of the vehicle. Follow the same procedure for changing the bulb on
the other side of the vehicle.
Controls
Safety
Driving tips
Brake lights
Turn signals
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 312 Donnerstag, 26. Juli 2007 9:16 09
312
Fuses and bulbs
– Turn the screwdriver anti-clockwise to loosen the screw
and then carefully remove the screw.
Applies to vehicles: with halogen main beam headlights
Removing rear light
To change the bulbs, you must remove the rear light.
Removing the light requires a certain degree of practical
skill.
– Gradually ease the light housing out of the rubber
3 and A
4 ) by pulling
mountings (positions ⇒ fig. 303 A
1 and A
2 . If necessary
alternately in direction of arrows A
use the tool for changing bulbs from your vehicle's
toolkit to carefully apply some pressure between posi3 and A
4 ⇒
tions A
.
– Unplug the electrical connector.
– Change the defective bulb ⇒ page 313.
Fig. 302 Luggage
compartment: Location of retaining screw
for rear light
Caution
When removing or installing the rear light, take care not to cause
any damage.
•
Removing the rear light in particular can lead to the paintwork or
rear light becoming damaged. This is another reason why we
recommend having the bulbs changed by a qualified workshop.
•
NEVER use metal tools (e.g. a screwdriver) or sharp or pointed
plastic tools to lever out the rear light - risk of damaging the paint.
Fig. 303 Removing
rear light from side
panel
– Check which of the bulbs is defective.
– Open the boot lid.
– Remove the side trim.
– Insert the screwdriver (from the tool kit) through the side
opening in the plastic screw ⇒ fig. 302.
Note
Make sure you have a soft cloth ready to place under the glass on
the rear light, to avoid any scratches.
document_0900452a81b1b9de.book Seite 313 Donnerstag, 26. Juli 2007 9:16 09
Fuses and bulbs
Changing bulbs
313
Applies to vehicles: with halogen main beam headlights
All bulbs can be changed easily after removing the rear
light.
Installing rear light
The rear light is easy to re-install.
Fig. 304 Rear light,
mounting plate is highlighted
– Detach the bulb carrier.
– Renew the defective bulb (pull to remove from plug-in
holder or turn to remove from bayonet holder)
⇒ page 305.
Fig. 305 Installing rear
light
To re-install the rear light, follow the steps for removal in
reverse sequence.
– Plug in the electrical connector. Make sure you hear it
click into place.
– Attach the bulb carrier.
– Insert the rear light into the rear light carrier ⇒ fig. 305.
– Re-install the rear light ⇒ page 313.
– Press the rear light into the two rubber mountings as far
as it will go. The rear light must be flush with the body
contour.
– Use the screw to secure the rear light from the luggage
compartment.
– Make sure that all bulbs for the rear lights are working.
Caution
Take care when installing the rear light to make sure there is no
damage to the paintwork or any of its components.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 314 Donnerstag, 26. Juli 2007 9:16 09
314
Fuses and bulbs
Changing bulbs in boot lid
Rear lights in boot lid
Fig. 308 Boot lid:
Removing bulb carrier
Fig. 306 Rear lights in
boot lid
•
•
The description for changing the bulb refers to the left rear
light unit; in principle the same procedure applies to the
right rear light unit.
– Check which of the bulbs is defective.
Rear fog light
– Open the boot lid.
Reversing light
Before you begin working, please make yourself familiar with the
different bulb versions ⇒ page 304.
– Take the screwdriver out of the vehicle tool kit.
Removing bulb carrier
– Release the retaining tab and remove the bulb carrier
from the light unit.
– Using the flat-blade side of the reversible screwdriver
insert, carefully detach the cover cap ⇒ fig. 307 -arrows-.
– Change the bulb ⇒ page 315.
Fig. 307 Boot lid:
Opening the cover in
the boot lid
document_0900452a81b1b9de.book Seite 315 Donnerstag, 26. Juli 2007 9:16 09
Fuses and bulbs
Changing bulb / installing bulb carrier
315
Applies to vehicles: with halogen main beam headlights
Number plate light
Fig. 310 Boot lid:
Removing number
plate light
Fig. 309 Bulb carrier
– Renew the defective bulb (pull to remove from plug-in
holder or turn to remove from bayonet holder)
⇒ page 305.
– Insert the bulb carrier into the rear light. Make sure you
hear the retaining tab click into place.
– Fit the cover back in the interior trim so that it engages.
– Put the screwdriver back into the tool kit.
Fig. 311 Number plate
light: Retaining
element
– Make sure that all bulbs for the rear lights are working.
Removing number plate light
– Take the screwdriver out of the vehicle tool kit
⇒ page 283.
– Insert the flat-blade side of the reversible screwdriver
insert into the slot on the number plate light ⇒ fig. 310.
– Using the screwdriver, start by pressing the number
plate light to the right -arrow 1- and then pull the number
plate light downwards from this position -arrow 2- and
out of the opening.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 316 Donnerstag, 26. Juli 2007 9:16 09
316
Fuses and bulbs
– Detach the number plate light.
Changing bulb
– Press the defective bulb out of the bulb holder and fit the
new bulb.
Installing number plate light
– First insert the side with the retaining element
⇒ page 315, fig. 311 and then carefully press the number
plate light into the opening.
– Check whether the new bulb is working.
document_0900452a81b1b9de.book Seite 317 Donnerstag, 26. Juli 2007 9:16 09
Fuses and bulbs
Controls
Safety
Driving tips
General maintenance
Self-help
317
Technical data
document_0900452a81b1b9de.book Seite 318 Donnerstag, 26. Juli 2007 9:16 09
318
document_0900452a81b1b9de.book Seite 319 Donnerstag, 26. Juli 2007 9:16 09
Technical data
319
document_0900452a81b1b9de.book Seite 320 Donnerstag, 26. Juli 2007 9:16 09
320
General notes
General notes
Explanation of technical data
Where not otherwise indicated or separately listed, all technical
data apply to vehicles with standard equipment for the German
market. Other figures may apply for special versions and export
models.
Please note that the details listed in the vehicle's registration documents can be taken as correct.
Engine data
The figures for engine power output are determined according to
EU standards.
Performance figures
The performance figures were measured without equipment which
may influence performance, such as mudflaps or extremely widesection tyres.
Kerb weight (unladen weight)
These figures (kerb weight according to the currently applicable
version of EU Directive 92/21/EEC) apply to the vehicle with the tank
90% full, with no special equipment. The figures include an additional 75 kg to allow for the weight of the driver.
When towing a trailer, the gross vehicle weight may be exceeded by
up to 30 kg and the maximum rear axle weight may be exceeded by
up to 80 kg.
Maximum trailer weights
The maximum trailer weights are calculated in accordance with the
currently applicable version of EU Directive 92/21/EEC.
The figures for a trailer with brakes, on gradients up to 8% are applicable only up to a maximum speed of 80 km/h (even though higher
speeds may be permitted when towing a trailer in some countries).
The figures for a trailer with brakes on gradients up to 12% and for
the weight of car and trailer on gradients up to 12% are applicable
up to a maximum speed of 100 km/h. This maximum speed must not
be exceeded even in countries where higher speeds are permitted.
Maximum draw bar loading
The vertical load exerted by the trailer drawbar on the ball joint of
the towing bracket must not exceed 80 kg.
In the interest of safety, we recommend applying the maximum
permitted draw bar weight. The stability of the trailer could be
adversely affected if too little weight is applied.
If the maximum permitted drawbar weight cannot be obtained, e.g.
when using small or light trailers, statutory regulations require that
the drawbar weight be at least 4% of the actual trailer weight (for
single-axle trailers or twin-axle trailers with an axle spacing less
than 1.0 m).
Dimensions
Length
mm
4703
Width
mm
1826
Width across mirrors
mm
1953
mm
1417-1437
Height,
1)
unladen1)
The height of the vehicle depends on the tyres and suspension.
Take care not to damage low-mounted parts of the car (such as the
spoiler or exhaust system) on steep ramps, uneven road surfaces or
roadside kerbs, etc.
This applies especially when the vehicle is fully laden.
document_0900452a81b1b9de.book Seite 321 Donnerstag, 26. Juli 2007 9:16 09
General notes
321
Capacities
Fuel tank
Front-wheel drive
ltr.
approx. 65
Four-wheel drive
ltr.
approx. 64
ltr.
approx. 4.5
Windscreen washer
Windscreen and
headlight washer system*
Vehicle identification data
You can also find the vehicle ID number on the sound
system or MMI*.
Fig. 313 Vehicle data
sticker
– Select: Function selector button CAR > Vehicle ID
number ⇒ fig. 312.
Vehicle identification number in the engine
compartment
Fig. 312 Display:
Vehicle identification
number
The vehicle identification number is located on the right-hand side
of the engine compartment.
Type plate
The type plate is located on the right-hand side of the engine
compartment. Vehicles for certain export countries have no type
plate.
Vehicle data sticker
The vehicle data sticker ⇒ fig. 313 is located near the battery in the
luggage compartment. One section of the vehicle data sticker is
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 322 Donnerstag, 26. Juli 2007 9:16 09
322
General notes
attached to the inside cover of the Service Schedule before the
vehicle is handed over.
The sticker lists the following data:
1
A
2
A
3
A
4
A
5
A
6
A
Vehicle identification number (chassis number)
Vehicle type / engine power / gearbox type
Engine and gearbox code letters
Paint No. / Interior equipment No.
Optional equipment codes
Fuel consumption and emissions
Fuel consumption and emissions
Information on the vehicle's fuel consumption and emissions is
6 :
given at the bottom of the vehicle data sticker A
A
A
B
A
C
A
D
A
Urban cycle consumption (ltr./100 km)
Extra-urban cycle consumption (ltr./100 km)
Combined cycle consumption (ltr./100 km)
Combined CO2 emissions (g/km)
The specified values were determined in accordance with the test
procedure prescribed by the currently applicable version of
Directive 80/1268/EEC. The specifications do not refer to an individual vehicle. The consumption figures achieved during normal
driving may differ from the test values quoted in accordance with
the above Directive, depending on special equipment fitted, vehicle
loading, personal driving style, road and traffic conditions, environmental factors and the condition of the car.
document_0900452a81b1b9de.book Seite 323 Donnerstag, 26. Juli 2007 9:16 09
Performance, weights and dimensions
323
Performance, weights and dimensions
Maximum trailer weights2)
Petrol engines
A4 1.8
Engine data
Power output
118 kW at 4500 - 6000 rpm
Maximum torque
250 Nm at 1500 - 4500 rpm
Cylinders, capacity
4 cylinders, 1,798 cm3
Fuel
Premium unleaded 95 RON or
regular unleaded 91 RON1)
Performance figures
km/h
Acceleration from 0 - 100 km/h sec.
1500
1500
Trailer with brakes on
gradients up to 12%
kg
1300
1300
Weight of vehicle and
trailer on gradients up to 12%
kg
3330
3370
Trailer without brakes
kg
740
750
Engine oil
VW 503 00, VW 504 00
AG
Inspection Service
VW 502 00, VW 503 00, VW 504 00
225
218
approx. 4.6 litres
8.6
8.6
Engine oil capacity
(including filter change)
MG
AG
1)
2)
Weights
MG = Manual gearbox / AG = Automatic gearbox
Gross vehicle weight
kg
1960
2000
Kerb weight (unladen weight)
kg
1410
1450
Maximum front axle weight
kg
1035
1060
Maximum rear axle weight
kg
1050
1060
Controls
AG
kg
LongLife Service
MG
Maximum speed
MG
Trailer with brakes on
gradients up to 8%
Safety
Driving tips
With slight loss of power
The specified trailer weights apply only to vehicles with a factoryfitted towing bracket.
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 324 Donnerstag, 26. Juli 2007 9:16 09
324
Performance, weights and dimensions
A4 3.2 quattro
Engine oil
Engine data
LongLife Service
VW 503 00, VW 504 00
Inspection Service
VW 502 00, VW 503 00 VW 504 00
Engine oil capacity
(including filter change)
approx. 6.2 litres
Power output
195 kW at 6500 rpm
Maximum torque
330 Nm at 3000 - 5000 rpm
Cylinders, capacity
6 cylinders, 3,197 cm3
Fuel
Premium unleaded 95 RON or
MG = manual gearbox
regular unleaded 91 RON1)
1)
2)
The specified trailer weights apply only to vehicles with a factoryfitted towing bracket.
Performance figures
Maximum speed
With slight loss of power
km/h
Acceleration from 0 - 100 km/h sec.
MG = 250
MG = 6.2
Weights
Gross vehicle weight
kg
MG = 2130
Kerb weight (unladen weight)
kg
MG = 1580
Maximum front axle weight
kg
MG = 1105
Maximum rear axle weight
kg
MG = 1145
Maximum trailer weights2)
Trailer with brakes on
gradients up to 8%
kg
MG = 2100
Trailer with brakes on
gradients up to 12%
kg
MG = 1900
Weight of vehicle and
trailer on gradients up to 12%
kg
MG = 4100
Trailer without brakes
kg
MG = 750
document_0900452a81b1b9de.book Seite 325 Donnerstag, 26. Juli 2007 9:16 09
Performance, weights and dimensions
Maximum trailer weights2)
Diesel engines
A4 2.0 TDI
Engine data1)
Power output
105 kW at 4200 rpm
Maximum torque
320 Nm at 1750 - 2500 rpm
Cylinders, capacity
4 cylinders, 1,968
Fuel
Diesel
cm3
MG
AG
Trailer with brakes on
gradients up to 8%
kg
1900
1900
Trailer with brakes on
gradients up to 12%
kg
1700
1700
Weight of vehicle and
trailer on gradients up to 12%
kg
3780
3815
Trailer without brakes
kg
750
750
Engine oil
Performance figures
Maximum speed
325
km/h
Acceleration from 0 - 100 km/h sec.
MG
AG
215
210
9.4
9.4
LongLife Service
VW 506 01, VW 507 00
vehicles with diesel particulate
filter*: only VW 507 00
Inspection Service
Weights
MG
AG
Gross vehicle weight
kg
2010
2045
Kerb weight (unladen weight)
kg
1460
1495
Maximum front axle weight
kg
1075
1100
Maximum rear axle weight
kg
1065
1070
VW 505 00, VW 505 01, VW 506 01,
VW 507 00
vehicles with diesel particulate
filter*: only VW 507 00
Engine oil capacity
(including filter change)
approx. 5.0 litres
MG = Manual gearbox / AG = Automatic gearbox
1) This engine is available with reduced power for some markets (see
car documentation). The performance figures may be slightly
different.
2)
The specified trailer weights apply only to vehicles with a factoryfitted towing bracket.
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 326 Donnerstag, 26. Juli 2007 9:16 09
326
Performance, weights and dimensions
A4 2.7 TDI
Engine oil
Engine data1)
LongLife Service
Power output
140 kW at 3500 - 4000 rpm
Maximum torque
400 Nm at 1400 - 3250 rpm
Cylinders, capacity
6 cylinders, 2,698 cm3
Fuel
Diesel
vehicles with diesel particulate filter*
only VW 507 00
Inspection Service
VW 505 00, VW 505 01, VW 506 01,
VW 507 00
vehicles with diesel particulate
filter*: only VW 507 00
Performance figures
Maximum speed
VW 506 01, VW 507 00
km/h
Acceleration from 0 - 100 km/h sec.
AG = 226
AG = 7.7
Engine oil capacity
(including filter change)
approx. 6.9 litres
Weights
AG = automatic gearbox
Gross vehicle weight
kg
AG = 2145
Kerb weight (unladen weight)
kg
AG = 1595
Maximum front axle weight
kg
AG = 1180
Maximum rear axle weight
kg
AG = 1080
Maximum trailer weights2)
Trailer with brakes on
gradients up to 8%
kg
AG = 1900
Trailer with brakes on
gradients up to 12%
kg
AG = 1700
Weight of vehicle and
trailer on gradients up to 12%
kg
AG = 3915
Trailer without brakes
kg
AG = 750
1) This engine is available with reduced power for some markets (see
car documentation). The performance figures may be slightly
different.
2)
The specified trailer weights apply only to vehicles with a factoryfitted towing bracket.
document_0900452a81b1b9de.book Seite 327 Donnerstag, 26. Juli 2007 9:16 09
Performance, weights and dimensions
A4 3.0 TDI quattro
Engine oil
LongLife Service
Engine data
Power output
176 kW at 4000 - 4400 rpm
Maximum torque
500 Nm at 1500 - 3000 rpm
Cylinders, capacity
6 cylinders, 2,967 cm3
Fuel
Diesel
km/h
Acceleration from 0 - 100 km/h sec.
VW 506 01, VW 507 00
vehicles with diesel particulate
filter*: only VW 507 00
Inspection Service
VW 505 00, VW 505 01, VW 506 01,
VW 507 00
vehicles with diesel particulate
filter*: only VW 507 00
Performance figures
Maximum speed
327
Engine oil capacity
(including filter change)
MG = 250
(governed)
approx. 6.9 litres
MG = 6.1
MG = manual gearbox
Weights
1)
Gross vehicle weight
kg
MG = 2205
Kerb weight (unladen weight)
kg
MG = 1655
Maximum front axle weight
kg
MG = 1180
Maximum rear axle weight
kg
MG = 1140
The specified trailer weights apply only to vehicles with a factoryfitted towing bracket.
Maximum trailer weights1)
Trailer with brakes on
gradients up to 8%
kg
MG = 2100
Trailer with brakes on
gradients up to 12%
kg
MG = 1900
Weight of vehicle and
trailer on gradients up to 12%
kg
MG = 4175
Trailer without brakes
kg
MG = 750
Controls
Safety
Driving tips
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 328 Donnerstag, 26. Juli 2007 9:16 09
328
document_0900452a81b1b9de.book Seite 329 Donnerstag, 26. Juli 2007 9:16 09
Index
329
document_0900452a81b1b9de.book Seite 330 Donnerstag, 26. Juli 2007 9:16 09
330
Index
A
Vehicles with manual gearbox . . . . . . 129
Volume of warning tone . . . . . . . . . . . 139
Abroad
Changing headlight dip settings . . . . . 59
adaptive light . . . . . . . . . . . . . . . . . . . . . . . 61
Defective . . . . . . . . . . . . . . . . . . . . . . . . 39
ABS
See Anti-lock brake system . . . . . . . . . 19
advanced key
Locking and unlocking the vehicle . . . 47
START ENGINE STOP button . . . . . . . 118
Starting the engine . . . . . . . . . . . . . . . 118
Switching on the ignition . . . . . . . . . . 118
AC mode . . . . . . . . . . . . . . . . . . . . . . . 98, 107
Acceleration figures
See Performance, weights and
dimensions . . . . . . . . . . . . . . . . . . . . 323
Accessories . . . . . . . . . . . . . . . . . . . . . . . . 277
Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Acoustic parking aid . . . . . . . . . . . . . . . . 169
Adapter for anti-theft wheel bolts . . . . . 292
adaptive cruise control . . . . . . . . . . . . . . 128
Driver intervention prompt . . . . 130, 138
Driver messages . . . . . . . . . . . . . . . . . 134
Driving program . . . . . . . . . . . . . . . . . 139
Error messages . . . . . . . . . . . . . . . . . . 136
Indicator lamps . . . . . . . . . . . . . . . . . . 134
No vehicle in front . . . . . . . . . . . . . . . 130
Overriding . . . . . . . . . . . . . . . . . . . . . . 130
Setting a new speed . . . . . . . . . . . . . . 131
Setting distance . . . . . . . . . . . . . . . . . 133
Setting speed . . . . . . . . . . . . . . . . . . . 131
Setting time interval . . . . . . . . . . . . . . 133
Settings . . . . . . . . . . . . . . . . . . . . . . . . 139
Status messages . . . . . . . . . . . . . . . . . 136
Switching off (with memory function) . . .
131, 132
Switching on and off . . . . . . . . . . . . . 131
System limitations . . . . . . . . . . . . . . . 140
Vehicle in front . . . . . . . . . . . . . . . . . . 130
Air conditioner . . . . . . . . . . . . . . . . . . 93, 101
AC mode . . . . . . . . . . . . . . . . . . . . . . . . . 98
See also Deluxe automatic air conditioner
93
Air recirculation mode
Deluxe automatic air conditioner . . . . 97
Deluxe automatic air conditioner plus . . .
105
Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
Deactivating . . . . . . . . . . . . . . . . . . . . . 208
Front airbags . . . . . . . . . . . . . . . . . . . . 203
Head-protection airbag . . . . . . . . . . . 207
Key-operated switch for front passenger's
airbag . . . . . . . . . . . . . . . . . . . . . . . . . 208
Side airbags . . . . . . . . . . . . . . . . . . . . . 205
Triggering . . . . . . . . . . . . . . . . . . . . . . 202
Warning lamp . . . . . . . . . . . . . . . . . . . . 17
Alarm system
See Anti-theft alarm system . . . . . . . . . 42
Anti-knock properties of petrol . . . . . . . . 251
Anti-lock brake system
How the system works . . . . . . . . . . . . 222
Warning lamp . . . . . . . . . . . . . . . . . . . . 19
Anti-theft alarm system . . . . . . . . . . . . . . . 42
Interior monitor . . . . . . . . . . . . . . . . . . . 50
Tow-away protection . . . . . . . . . . . . . . 50
Anti-theft wheel bolts . . . . . . . . . . . . . . . . 292
Armrest (front)
Adjusting . . . . . . . . . . . . . . . . . . . . . . . . 78
Storage compartment . . . . . . . . . . . . . . 78
Ashtrays
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Audi braking guard . . . . . . . . . . . . . . . . . .
Error messages . . . . . . . . . . . . . . . . . .
Settings . . . . . . . . . . . . . . . . . . . . . . . .
Status messages . . . . . . . . . . . . . . . . .
Switching on and off . . . . . . . . . . . . . .
142
143
144
143
144
Audi drive select . . . . . . . . . . . . . . . . . . . . 159
Dynamic steering . . . . . . . . . . . . . . . . 159
Suspension control . . . . . . . . . . . . . . . 159
Audi hold assist . . . . . . . . . . . . . . . . . . . . 124
Warning lamp . . . . . . . . . . . . . . . . . . . . 19
Audi lane assist
See lane assist . . . . . . . . . . . . . . . . . . . 145
Audi parking system . . . . . . . . . . . . . . . . . 169
Alterations to the vehicle . . . . . . . . . . . . . 277
Audi parking system advanced . . . . . . . . 171
Alternator
Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Audi parking system plus . . . . . . . . . . . . 170
Anti-dazzle interior mirror . . . . . . . . . . . . . 69
Auto-check control . . . . . . . . . . . . . . . . . . . 30
Anti-freeze additive . . . . . . . . . . . . . . . . . 260
Auto Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
document_0900452a81b1b9de.book Seite 331 Donnerstag, 26. Juli 2007 9:16 09
Index
Automatic air conditioner plus
See Deluxe automatic air conditioner plus
101
Automatic cruise control
See adaptive cruise control . . . . . . . . 128
Automatic gearbox
Dynamic gear control program . . . . . 166
Kick-down feature . . . . . . . . . . . . . . . . 165
Manual release (multitronic®) . . . . . . 168
multitronic® . . . . . . . . . . . . . . . . . . . . . 162
Paddle levers (tiptronic mode) . . . . . . 167
Safety interlock for ignition key . . . . . 116
Selector lever lock . . . . . . . . . . . . . . . . 165
Selector lever positions . . . . . . . . . . . 163
Steering wheel with paddle levers . . 167
tiptronic . . . . . . . . . . . . . . . . . . . . 162, 166
B
Battery
Charging . . . . . . . . . . . . . . . . . . . . . . . .
Low charge . . . . . . . . . . . . . . . . . . . . . .
Power level . . . . . . . . . . . . . . . . . . . . . .
Power management . . . . . . . . . . . . . .
Replacing . . . . . . . . . . . . . . . . . . . . . . .
Winter conditions . . . . . . . . . . . . . . . .
265
226
226
226
266
263
Battery power . . . . . . . . . . . . . . . . . . . . . . . 38
Bayonet fastener
Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
Bulb holder . . . . . . . . . . . . . . . . . . . . . . 306
Belt tensioners . . . . . . . . . . . . . . . . . . . . . . 199
Bicycle rack
Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Automatic headlight control . . . . . . . . . . . 57
Biodiesel . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Automatic headlights . . . . . . . . . . . . . . . . . 59
Bioethanol fuel . . . . . . . . . . . . . . . . . . . . . 251
Auxiliary heating
Deluxe automatic air conditioner plus
110
Description . . . . . . . . . . . . . . . . . . . . . .
Remote control . . . . . . . . . . . . . . . . . .
Running time . . . . . . . . . . . . . . . . . . . .
Switching on/off immediately . . . . . .
Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blower
Deluxe automatic air conditioner . . . . . 96
Deluxe automatic air conditioner plus . .
104
..
110
113
112
111
111
Average fuel consumption . . . . . . . . . . . . . 25
Average speed . . . . . . . . . . . . . . . . . . . . . . . 25
Axle weights
See Performance, weights and
dimensions . . . . . . . . . . . . . . . . . . . . 323
Controls
Safety
Bonnet
Closing . . . . . . . . . . . . . . . . . . . . . . . . . 256
Opening . . . . . . . . . . . . . . . . . . . . . . . . 254
Releasing . . . . . . . . . . . . . . . . . . . . . . . 254
Boot
See Loading luggage compartment . 192
See Luggage compartment . . . . . . . . . . 79
Boot lid
Central locking system . . . . . . . . . . . . . 51
Manual release . . . . . . . . . . . . . . . . . . . . 52
Driving tips
331
Brake system
Brake assist system . . . . . . . . . . . . . . . 222
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . 262
Brake light defective . . . . . . . . . . . . . . . 37
Brake pads worn . . . . . . . . . . . . . . . . . . 37
Brake servo . . . . . . . . . . . . . . . . . . . . . . 224
Electro-mechanical parking brake . . . 121
General notes . . . . . . . . . . . . . . . . . . . . 224
Malfunction . . . . . . . . . . . . . . . . . . . . . . 32
Warning lamp . . . . . . . . . . . . . . . . . . . . . 20
braking guard
See Audi braking guard . . . . . . . . . . . . 142
Bulb holder
Bayonet fastener . . . . . . . . . . . . . . . . . 306
Bulb monitor . . . . . . . . . . . . . . . . . . . . . . . . 37
Bulbs
Bayonet fastener . . . . . . . . . . . . . . . . . 305
Changing (general notes) . . . . . . . . . . 304
Bulbs, changing . . . . . . . . . . . . . . . . . . . . . 304
Brake lights . . . . . . . . . . . . . . . . . . . . . . 311
Bulb holder with bayonet fastener . 305,
306
Dipped headlights . . . . . . . . . . . . . . . . 308
Front fog lights . . . . . . . . . . . . . . . . . . . 310
Main beam headlights . . . . . . . . . . . . . 307
Number plate light . . . . . . . . . . . . . . . . 315
Rear fog light . . . . . . . . . . . . . . . . . . . . 314
Rear lights . . . . . . . . . . . . . . . . . . . . . . . 311
Reversing light . . . . . . . . . . . . . . . . . . . 314
Turn signals (rear) . . . . . . . . . . . . . . . . 311
Business equipment . . . . . . . . . . . . . . . . . 278
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 332 Donnerstag, 26. Juli 2007 9:16 09
332
Index
C
Cigarette lighter . . . . . . . . . . . . . . . . . . . . . 87
Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 321
Cleaning Alcantara . . . . . . . . . . . . . . . . . . 250
Car keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Cleaning seat covers
Alcantara . . . . . . . . . . . . . . . . . . . . . . . 250
Natural leather . . . . . . . . . . . . . . . . . . 249
Textile covers . . . . . . . . . . . . . . . . . . . . 247
Cruise control system
Adjusting stored speed . . . . . . . . . . . 126
Indicator lamp . . . . . . . . . . . . . . . . . . . . 19
Pre-selecting a speed . . . . . . . . . . . . . 127
Switching off . . . . . . . . . . . . . . . . . . . . 127
Switching on . . . . . . . . . . . . . . . . . . . . 125
See also adaptive cruise control . . . . 128
Cleaning textile covers and trim parts . . 247
Cup holders . . . . . . . . . . . . . . . . . . . . . . . . . 85
Clock, setting . . . . . . . . . . . . . . . . . . . . . . . 13
Current fuel consumption . . . . . . . . . . . . . 25
Closing
Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . 256
Sun roof . . . . . . . . . . . . . . . . . . . . . . . . . 55
D
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
Care of vehicle . . . . . . . . . . . . . . . . . . . . . 244
Catalytic converter . . . . . . . . . . . . . . . . . . 229
Central locking system . . . . . . . . . . . . . . . 42
Boot lid . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Deadlock mechanism . . . . . . . . . . . . . . 48
Fuel tank flap . . . . . . . . . . . . . . . . . . . . 252
Locking . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Locking and unlocking the vehicle from
inside . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Manual locking . . . . . . . . . . . . . . . . . . . 51
Opening and closing windows . . . . . . 54
Sun roof . . . . . . . . . . . . . . . . . . . . . . . . . 54
Switches on driver's door . . . . . . . . . . 49
Unlocking . . . . . . . . . . . . . . . . . . . . . . . . 48
Coat hooks . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Colour code . . . . . . . . . . . . . . . . . . . . . . . . 321
DCP
See Dynamic gear control program . 166
Compact temporary spare wheel
See Spare wheel . . . . . . . . . . . . . . . . . 284
Deactivating front passenger's airbag . . 208
Compartment for (sun)glasses . . . . . . . . . 91
Changing a wheel . . . . . . . . . . . . . . . . . . . 288
Compass in mirror . . . . . . . . . . . . . . . . . . . 71
Changing bulbs
See Bulbs . . . . . . . . . . . . . . . . . . . . . . . 304
Controls and displays
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chassis number . . . . . . . . . . . . . . . . . . . . 321
Convenience open/close function . . . . . . 54
Child safety . . . . . . . . . . . . . . . . . . . . . . . . 210
Side airbags . . . . . . . . . . . . . . . . . . . . . 212
Cooling system
Anti-freeze additive . . . . . . . . . . . . . . . 260
Checking coolant level . . . . . . . . . . . . 261
Coolant . . . . . . . . . . . . . . . . . . . . . . . . . 260
Coolant temperature gauge . . . . . . . . . 11
Malfunction . . . . . . . . . . . . . . . . . . . . . . 33
Radiator fan . . . . . . . . . . . . . . . . . . . . . 262
Topping up coolant . . . . . . . . . . . . . . . 261
213
213
216
218
211
210
Child-proof catches
Rear doors . . . . . . . . . . . . . . . . . . . . . . . 53
Daytime running lights . . . . . . . . . . . . . . . 59
coming home . . . . . . . . . . . . . . . . . . . . . . . 59
Cetane number . . . . . . . . . . . . . . . . . . . . . 251
Child safety seat . . . . . . . . . . . . . . . . . . . .
Child seat categories . . . . . . . . . . . . .
Fitting . . . . . . . . . . . . . . . . . . . . . . . . . .
ISOFIX system . . . . . . . . . . . . . . . . . . .
On front passenger's seat . . . . . . . . .
Safety notes . . . . . . . . . . . . . . . . . . . . .
Date display . . . . . . . . . . . . . . . . . . . . . . . . . 13
Deadlock mechanism . . . . . . . . . . . . . . 42, 48
Defrosting windows . . . . . . . . . . . . . . 98, 106
Deluxe automatic air conditioner . . . . . . . 93
Air distribution . . . . . . . . . . . . . . . . . . . 97
Air outlets . . . . . . . . . . . . . . . . . . . . . . . . 99
Air outlets for rear passengers . . . . . . 99
Air recirculation mode . . . . . . . . . . . . . 97
Automatic mode . . . . . . . . . . . . . . . . . . 95
Basic settings . . . . . . . . . . . . . . . . . . . . 100
Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Controls . . . . . . . . . . . . . . . . . . . . . . . . . 94
Defrosting . . . . . . . . . . . . . . . . . . . . . . . 98
Description . . . . . . . . . . . . . . . . . . . . . . . 93
Economical operation . . . . . . . . . . . . . 100
Heated rear window . . . . . . . . . . . . . . . 98
Seat heating, front . . . . . . . . . . . . . . . 114
document_0900452a81b1b9de.book Seite 333 Donnerstag, 26. Juli 2007 9:16 09
Index
Supplementary heater . . . . . . . . . . . . 101
Switching on and off . . . . . . . . . . . . . . . 95
Temperature . . . . . . . . . . . . . . . . . . . . . . 96
Deluxe automatic air conditioner plus . .
AC mode . . . . . . . . . . . . . . . . . . . . . . . .
Air distribution . . . . . . . . . . . . . . . . . . .
Air outlets . . . . . . . . . . . . . . . . . . . . . . .
Air outlets for rear passengers . . . . .
Air recirculation mode . . . . . . . . . . . .
Automatic mode . . . . . . . . . . . . . . . . .
Automatic recirculation . . . . . . . . . . .
Auxiliary heating . . . . . . . . . . . . . . . . .
Auxiliary heating - remote control . . .
Auxiliary heating - running time . . . .
Basic settings . . . . . . . . . . . . . . . . . . . .
Blower . . . . . . . . . . . . . . . . . . . . . . . . . .
Controls . . . . . . . . . . . . . . . . . . . . . . . .
Defrosting . . . . . . . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . .
Economical operation . . . . . . . . . . . . .
Heated rear window . . . . . . . . . . . . . .
Supplementary heater . . . . . . . . . . . .
Switching on and off . . . . . . . . . . . . . .
Synchronisation . . . . . . . . . . . . . . . . . .
Temperature . . . . . . . . . . . . . . . . . . . . .
101
107
106
107
108
105
103
109
110
113
112
109
104
102
106
101
108
106
110
103
109
104
Diesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Diesel particulate filter . . . . . . . . . . . . 38, 229
Engine oil . . . . . . . . . . . . . . . . . . . . . . . 257
Digital clock . . . . . . . . . . . . . . . . . . . . . . . . . 13
Dipped headlights . . . . . . . . . . . . . . . . . . . . 57
Defective . . . . . . . . . . . . . . . . . . . . . . . . . 37
Driving on left . . . . . . . . . . . . . . . . . . . . . . . 59
DIS
See Driver information system . . . . . . . 21
Driving safety . . . . . . . . . . . . . . . . . . . . . . . 187
Distance control system
See adaptive cruise control . . . . . . . . 128
Dust filter
Deluxe automatic air conditioner . . . . . 93
Deluxe automatic air conditioner plus . .
101
Door catches/boot lid warning . . . . . . . . . 24
Doors
Child-proof catches . . . . . . . . . . . . . . . . 53
Manual locking . . . . . . . . . . . . . . . . . . . . 51
Dynamic gear control program . . . . . . . . 166
E
Economical driving . . . . . . . . . . . . . . . . . . 229
EDL
See Electronic differential lock . . . . . . . 19
Electric seat adjustment
See Seat adjustment . . . . . . . . . . . . . . . 74
Electric windows . . . . . . . . . . . . . . . . . . . . .
Central locking system . . . . . . . . . . . . .
Convenience open/close function . . . .
Malfunctions . . . . . . . . . . . . . . . . . . . . . .
Settings . . . . . . . . . . . . . . . . . . . . . . . . . .
53
54
54
55
55
Driver messages . . . . . . . . . . . . . . . . . . . . . 30
Electrical accessories
See Electrical socket . . . . . . . . . . . . . . . 88
Driving
Run flat tyres . . . . . . . . . . . . . . . . . . . . 275
Electrical socket . . . . . . . . . . . . . . . . . . . 87, 88
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 320
Driving away from a standstill . . . . . . . . . 122
Driving away when towing a trailer . . . . 123
Safety
DVD player . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Driver information system . . . . . . . . . . . . .
Auto-check control . . . . . . . . . . . . . . . .
Bulb monitor . . . . . . . . . . . . . . . . . . . . .
CD and radio display . . . . . . . . . . . . . . .
Digital speedometer . . . . . . . . . . . . . . .
Door catches/boot lid warning . . . . . . .
Driver messages . . . . . . . . . . . . . . . . . .
On-board computer . . . . . . . . . . . . . . . .
Outside temperature display . . . . . . . .
Red symbols . . . . . . . . . . . . . . . . . . . . . .
Service interval display . . . . . . . . . . . . .
Speed warning . . . . . . . . . . . . . . . . . . . .
Yellow symbols . . . . . . . . . . . . . . . . . . .
Digital speedometer . . . . . . . . . . . . . . . . . . 23
Controls
Driving time . . . . . . . . . . . . . . . . . . . . . . . . . 25
Dynamic steering . . . . . . . . . 16, 36, 159, 222
Driving abroad
Headlights . . . . . . . . . . . . . . . . . . . . . . . 59
Unleaded fuel . . . . . . . . . . . . . . . . . . . . 251
Digital compass . . . . . . . . . . . . . . . . . . . . . . 71
Driving on right . . . . . . . . . . . . . . . . . . . . . . 59
Driver
See Sitting position . . . . . . . . . . . . . . . 188
21
30
37
22
23
24
30
25
22
31
24
28
35
Driving tips
333
Electro-mechanical parking brake . . . . . .
Auto release function . . . . . . . . . . . . .
Driving away from a standstill . . . . . .
Driving away when towing a trailer . .
Emergency braking function . . . . . . .
Malfunction . . . . . . . . . . . . . . . . . . . . .
General maintenance
Self-help
124
122
122
123
123
123
Technical data
document_0900452a81b1b9de.book Seite 334 Donnerstag, 26. Juli 2007 9:16 09
334
Index
Operation . . . . . . . . . . . . . . . . . . . . . . . 121
Parking . . . . . . . . . . . . . . . . . . . . . . . . . 122
Releasing and applying . . . . . . . . . . . 121
Warning lamp . . . . . . . . . . . . . . . . . 19, 20
Electronic differential lock
How the system works . . . . . . . . . . . . 222
Warning lamp . . . . . . . . . . . . . . . . . . . . 19
Electronic immobiliser . . . . . . . . . . . . . 14, 43
Topping up . . . . . . . . . . . . . . . . . . . . . . 259
See also Performance, weights and
dimensions . . . . . . . . . . . . . . . . . . . . 323
Engine oil capacity
See Performance, weights and
dimensions . . . . . . . . . . . . . . . . . . . . 323
Engine oil pressure
Warning lamp . . . . . . . . . . . . . . . . . . . . 33
Electronic stabilisation program
How the system works . . . . . . . . . . . . 222
Warning lamp . . . . . . . . . . . . . . . . . . . . 17
Engine oil sensor
Malfunction . . . . . . . . . . . . . . . . . . . . . . 38
Emergency braking function . . . . . . . . . . 123
Environmental tips
Filling the tank . . . . . . . . . . . . . . . . . . . 252
Heated rear window . . . . . . . . . . . 98, 106
Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
Roof carrier . . . . . . . . . . . . . . . . . . . . . . 84
Emergency key . . . . . . . . . . . . . . . . . . . . . . 45
Emergency release
Ignition key . . . . . . . . . . . . . . . . . . . . . . 46
Emission control systems
Catalytic converter . . . . . . . . . . . . . . . 229
Diesel particulate filter . . . . . . . . . . . . 229
Emissions . . . . . . . . . . . . . . . . . . . . . . . . . 321
Engine compartment
Safety notes . . . . . . . . . . . . . . . . . . . . . 255
Environmental compatibility . . . . . . . . . . 231
EPC
See Engine management . . . . . . . . . . . 16
ESP
See Electronic stabilisation program . 17
Front passenger
See Sitting position . . . . . . . . . . . . . . . 189
Fuel
Biodiesel . . . . . . . . . . . . . . . . . . . . . . . . 251
Capacity . . . . . . . . . . . . . . . . . . . . . . . . 321
Consumption . . . . . . . . . . . . . . . . . . . . 321
Current fuel consumption . . . . . . . . . . 25
Diesel . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . 251
Fuel level low . . . . . . . . . . . . . . . . . . . . . 37
Petrol . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Saving fuel . . . . . . . . . . . . . . . . . . . . . . 229
Fuel consumption . . . . . . . . . . . . . . . . . . . 321
Fuel range . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Fuel tank flap . . . . . . . . . . . . . . . . . . . . . . . 252
Fuse, changing . . . . . . . . . . . . . . . . . . . . . 300
G
Garage door opener . . . . . . . . . . . . . . . . . 179
Ethanol fuel . . . . . . . . . . . . . . . . . . . . . . . . 251
Gear-change indicator . . . . . . . . . . . . . . . . 22
Engine compartment layout . . . . . . . . . . 256
Exterior mirrors . . . . . . . . . . . . . . . . . . . . . . 70
Engine data
See Performance, weights and
dimensions . . . . . . . . . . . . . . . . . . . . 323
Generator
See Alternator . . . . . . . . . . . . . . . . . . . . 32
F
Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Engine hood
See Bonnet . . . . . . . . . . . . . . . . . . . . . . 254
Engine management
(EPC) warning lamp . . . . . . . . . . . . . . . 16
Engine oil . . . . . . . . . . . . . . . . . . . . . . 34, 257
Checking oil level . . . . . . . . . . . . 258, 259
Consumption . . . . . . . . . . . . . . . . 258, 259
LongLife Service . . . . . . . . . . . . . . . . . 257
Fastening rings . . . . . . . . . . . . . . . . . . 79, 193
Filling the tank . . . . . . . . . . . . . . . . . . . . . 252
Releasing the tank flap manually . . . 253
Fire extinguisher . . . . . . . . . . . . . . . . . . . . 283
First-aid kit . . . . . . . . . . . . . . . . . . . . . . . . . 282
Floor mats . . . . . . . . . . . . . . . . . . . . . 191, 192
Fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Four-wheel drive . . . . . . . . . . . . . . . . . . . . 226
Glow plug system
Indicator lamp . . . . . . . . . . . . . . . . . . . . 16
H
Handbrake
See Electro-mechanical parking brake . . .
121
document_0900452a81b1b9de.book Seite 335 Donnerstag, 26. Juli 2007 9:16 09
Index
Hazard warning lights . . . . . . . . . . . . . . . . 61
Indicator lamp . . . . . . . . . . . . . . . . . . . . 18
I
J
Head restraints
Front seats . . . . . . . . . . . . . . . . . . . . . . . 77
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . 78
Ignition key
Emergency release . . . . . . . . . . . . . . . . 46
Safety interlock . . . . . . . . . . . . . . . . . . 116
Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . 283, 290
Headlamp converter . . . . . . . . . . . . . . . . . . 59
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . 116
Malfunction . . . . . . . . . . . . . . . . . . . 34, 39
Headlight flasher . . . . . . . . . . . . . . . . . . . . . 62
Headlight range control . . . . . . . . . . . . . . . 60
Malfunction . . . . . . . . . . . . . . . . . . . . . . 39
Headlights . . . . . . . . . . . . . . . . . . . . . . . . . .
adaptive light . . . . . . . . . . . . . . . . . . . . .
Changing dip settings . . . . . . . . . . . . . .
Driving abroad . . . . . . . . . . . . . . . . . . . .
Headlight range control . . . . . . . . . . . .
Washer system . . . . . . . . . . . . . . . . . . . .
57
61
59
59
60
67
Heated
Exterior mirrors . . . . . . . . . . . . . . . . . . . 70
Front seats (deluxe automatic air
conditioner) . . . . . . . . . . . . . . . . . . . . 114
Rear seats . . . . . . . . . . . . . . . . . . . . . . . 115
Rear window . . . . . . . . . . . . . . . . . 98, 106
Washer jets . . . . . . . . . . . . . . . . . . . . . . . 65
Heated rear window . . . . . . . . . . . . . . 98, 106
Heating
Deluxe automatic air conditioner . . . . 93
Deluxe automatic air conditioner plus . .
101
HomeLink . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Controls
Safety
Immobiliser . . . . . . . . . . . . . . . . . . . . . . 14, 43
Indicator lamps . . . . . . . . . . . . . . . . . . . . . . 15
adaptive cruise control . . . . . . . . . . . . 134
Cruise control system . . . . . . . . . . . . . . 19
Glow plug system . . . . . . . . . . . . . . . . . 16
Main beam headlights . . . . . . . . . . . . . 18
Overview . . . . . . . . . . . . . . . . . . . . . . . . . 15
Trailer turn signals . . . . . . . . . . . . . . . . 18
Turn signals . . . . . . . . . . . . . . . . . . . . . . 18
Inflation pressures (tyres) . . . . . . . . . 39, 268
Inspection intervals . . . . . . . . . . . . . . . . . . . 24
Instrument cluster . . . . . . . . . . . . . . . . . . . . 11
Instrument lighting . . . . . . . . . . . . . . . . . . . 59
Interior lights
Dimming . . . . . . . . . . . . . . . . . . . . . . . . . 63
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Jacking points . . . . . . . . . . . . . . . . . . . . . . 290
Jump-starting . . . . . . . . . . . . . . . . . . . . . . 293
K
Key-operated switch for front passenger's
airbag . . . . . . . . . . . . . . . . . . . . . . . . . 208
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emergency key . . . . . . . . . . . . . . . . . . . .
Replacement keys . . . . . . . . . . . . . . . . .
Replacing the battery . . . . . . . . . . . . . .
43
45
43
45
Kick-down feature . . . . . . . . . . . . . . . . . . . 165
L
lane assist
Changing settings on the MMI . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . .
Indicator lamp in instrument cluster .
Instrument cluster display . . . . . . . . .
Switching on and off . . . . . . . . . . . . . .
147
145
145
146
145
Interior mirrors
See Mirrors . . . . . . . . . . . . . . . . . . . . 68, 69
Leather care
Alcantara . . . . . . . . . . . . . . . . . . . . . . . . 250
Natural leather . . . . . . . . . . . . . . . . . . . 249
Interior monitor . . . . . . . . . . . . . . . . . . . . . . 50
leaving home . . . . . . . . . . . . . . . . . . . . . . . . 59
Intermittent wipe . . . . . . . . . . . . . . . . . . . . . 65
Rain sensor . . . . . . . . . . . . . . . . . . . . . . . 65
Light sensor . . . . . . . . . . . . . . . . . . . . . . . . . 57
ISOFIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
coming home . . . . . . . . . . . . . . . . . . . . . 59
Daytime running lights . . . . . . . . . . . . . 59
Driving tips
335
Light sensor defective . . . . . . . . . . . . . . . . . 37
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 336 Donnerstag, 26. Juli 2007 9:16 09
336
Index
Exterior lighting . . . . . . . . . . . . . . . . . .
Front fog lights . . . . . . . . . . . . . . . . . . .
Headlight control . . . . . . . . . . . . . . . . .
leaving home . . . . . . . . . . . . . . . . . . . . .
Rear fog lights . . . . . . . . . . . . . . . . . . . .
Switching on and off . . . . . . . . . . . . . .
59
58
57
59
58
57
Loading luggage compartment . . . . . . . 192
Load-through hatch . . . . . . . . . . . . . . . . . . 82
Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Central locking system . . . . . . . . . . . . . 48
Locking and unlocking the vehicle from inside
Central locking system . . . . . . . . . . . . . 49
Manual operation
Boot lid . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Fuel tank flap . . . . . . . . . . . . . . . . . . . . 253
Number plate light
Changing bulb . . . . . . . . . . . . . . . . . . . 315
Manual release
Selector lever (multitronic®) . . . . . . . 168
O
Maximum speed
See Performance, weights and
dimensions . . . . . . . . . . . . . . . . . . . . 323
Octane rating . . . . . . . . . . . . . . . . . . . . . . . 251
Memory for driver's seat . . . . . . . . . . . . . .
Activating remote control key . . . . . . .
Recalling settings . . . . . . . . . . . . . . . . .
Storing settings . . . . . . . . . . . . . . . . . . .
75
77
76
76
Oil consumption . . . . . . . . . . . . . . . . 258, 259
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Opening
Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . 254
Sun roof . . . . . . . . . . . . . . . . . . . . . . . . . 55
Locking doors manually . . . . . . . . . . . . . . 51
Mileage recorder . . . . . . . . . . . . . . . . . . . . 14
LongLife Service . . . . . . . . . . . . . . . . . . . . 257
Minimising pollution . . . . . . . . . . . . . . . . 229
Luggage compartment . . . . . . . . . . . . . . . 79
Extending . . . . . . . . . . . . . . . . . . . . . . . . 81
Fastening rings . . . . . . . . . . . . . . . . . . . 79
Loading . . . . . . . . . . . . . . . . . . . . . . . . . 79
Side storage compartment . . . . . . . . . 80
Stretch net . . . . . . . . . . . . . . . . . . . . . . . 80
Transport bag . . . . . . . . . . . . . . . . . . . . 82
See also Loading luggage compartment .
192
Mirrors
Anti-dazzle setting . . . . . . . . . . . . . . . .
Automatic anti-dazzle exterior mirrors
Automatic anti-dazzle interior mirror .
Exterior mirrors . . . . . . . . . . . . . . . . . . .
Interior mirror . . . . . . . . . . . . . . . . . . . .
Make-up mirrors . . . . . . . . . . . . . . . . . .
Oil
See Engine oil . . . . . . . . . . . . . . . 258, 259
Oil dipstick . . . . . . . . . . . . . . . . . . . . . . . . . 258
Oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
On-board computer . . . . . . . . . . . . . . . . . . 25
Outside temperature display . . . . . . . . . . . 22
69
71
69
70
68
64
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
MMI control console, cleaning . . . . . . . . 247
Paint damage . . . . . . . . . . . . . . . . . . . . . . 246
MMI display, cleaning . . . . . . . . . . . . . . . 247
Paint No. . . . . . . . . . . . . . . . . . . . . . . . . . . 321
Luggage rack
See Roof carrier . . . . . . . . . . . . . . . . . . . 83
Mobile phones . . . . . . . . . . . . . . . . . . . . . 278
Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Modifications . . . . . . . . . . . . . . . . . . . . . . 277
Parking brake . . . . . . . . . . . . . . . . . . . . . . 121
M
multitronic® . . . . . . . . . . . . . . . . . . . . . . . 162
Driving with multitronic® . . . . . . . . . 162
Parking lights . . . . . . . . . . . . . . . . . . . . . . . 62
Main beam headlights . . . . . . . . . . . . . . . . 62
Indicator lamp . . . . . . . . . . . . . . . . . . . . 18
N
Make-up mirrors . . . . . . . . . . . . . . . . . . . . . 64
Natural leather . . . . . . . . . . . . . . . . . . . . . 248
P
Paddle levers
tiptronic . . . . . . . . . . . . . . . . . . . . . . . . 167
parking system . . . . . . . . . . . . . . . . . . . . .
Reversing camera, parking mode 1 . .
Reversing camera, parking mode 2 . .
Safety notes on reversing camera . . .
Switching graphic display on and off
169
174
175
172
177
document_0900452a81b1b9de.book Seite 337 Donnerstag, 26. Juli 2007 9:16 09
Index
Q
Replacement keys . . . . . . . . . . . . . . . . . . . . 43
Quartz clock . . . . . . . . . . . . . . . . . . . . . . . . . 13
Reset button . . . . . . . . . . . . . . . . . . . . . . . . . 14
Retaining net . . . . . . . . . . . . . . . . . . . . . . . . 80
parking system plus . . . . . . . . . . . . . . . . . 170
quattro
See Four-wheel drive . . . . . . . . . . . . . . 226
Parking the car
multitronic® . . . . . . . . . . . . . . . . . . . . . 162
R
Reverse gear
Automatic gearbox . . . . . . . . . . . . . . . 163
Switching reversing camera on and off .
177
Towing bracket . . . . . . . . . . . . . . . . . . 177
parking system advanced . . . . . . . . . . . . 171
Particulate filter
See Diesel particulate filter . . . . . . . . . 229
Passengers
See Sitting position . . . . . . . . . . . . . . . 189
Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Performance figures
See Performance, weights and
dimensions . . . . . . . . . . . . . . . . . . . . 323
Performance, weights and dimensions . 323
General notes . . . . . . . . . . . . . . . . . . . . 320
Personalised remote control key . . . . . . . . 43
Petrol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Polishing . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Pollen filter
Deluxe automatic air conditioner . . . . 93
Deluxe automatic air conditioner plus . .
101
Replacement parts . . . . . . . . . . . . . . . . . . 277
Radio transmitters . . . . . . . . . . . . . . . . . . 278
Fixed installation . . . . . . . . . . . . . . . . . 278
Mobile equipment . . . . . . . . . . . . . . . . 278
Radio-controlled clock . . . . . . . . . . . . . . . . 13
Radio-operated remote control
See Remote control keys . . . . . . . . . . . . 43
Rain sensor . . . . . . . . . . . . . . . . . . . . . . . . . 65
Rain sensor defective . . . . . . . . . . . . . . . . . 37
Reading lights
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Rear centre console
Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Rear fog lights . . . . . . . . . . . . . . . . . . . . . . . 58
Rear lights
Defective . . . . . . . . . . . . . . . . . . . . . . . . . 37
Rev counter . . . . . . . . . . . . . . . . . . . . . . . . . 12
Reversing camera
Parking mode 1 . . . . . . . . . . . . . . . . . . 174
Parking mode 2 . . . . . . . . . . . . . . . . . . 175
RME fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Roof carrier . . . . . . . . . . . . . . . . . . . . . . . . . 83
Attachment points . . . . . . . . . . . . . . . . . 84
Roof load . . . . . . . . . . . . . . . . . . . . . . . . . 84
Run flat tyres . . . . . . . . . . . . . . . . . . . . . . .
Driving . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction . . . . . . . . . . . . . . . . . . . . .
Renewing defective components . . . .
Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . .
274
275
274
276
274
Running in . . . . . . . . . . . . . . . . . . . . . . . . . 229
New engine . . . . . . . . . . . . . . . . . . . . . . 229
New tyres . . . . . . . . . . . . . . . . . . . . . . . 268
S
Pollution filter
Deluxe automatic air conditioner . . . . 93
Deluxe automatic air conditioner plus . .
101
Rear View camera
See Reversing camera . . . . . . . . . . . . . 173
Rear view mirrors
See Mirrors . . . . . . . . . . . . . . . . . . . . 68, 69
Safe driving . . . . . . . . . . . . . . . . . . . . . . . . 186
Power management . . . . . . . . . . . . . . . . . 226
Battery power . . . . . . . . . . . . . . . . . . . . 228
Driver message . . . . . . . . . . . . . . . . . . 228
Rear window, sun blind . . . . . . . . . . . . . . . 64
Safety features . . . . . . . . . . . . . . . . . . . . . . 186
Remote control keys . . . . . . . . . . . . . . . . . .
Indicator lamp . . . . . . . . . . . . . . . . . . . .
Replacing the battery . . . . . . . . . . . . . .
Unlocking and locking . . . . . . . . . . . . .
Seat adjustment
Backrest angle (manual) . . . . . . . . . . . . 73
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . 74
Forwards and backwards (manual) . . . 73
Power steering . . . . . . . . . . . . . . . 16, 36, 225
Pressure (tyres) . . . . . . . . . . . . . . . . . . . . . . 39
Controls
Safety
337
Driving tips
43
44
45
47
SAFE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 338 Donnerstag, 26. Juli 2007 9:16 09
338
Index
Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Seat height (manual) . . . . . . . . . . . . . . 73
Safety notes . . . . . . . . . . . . . . . . . . . . . 157
Switching on and off . . . . . . . . . . . . . 149
Stretch net . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Seat belt height adjustment . . . . . . . . . . 199
Side lights . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . 194
Adjusting seat belts . . . . . . . . . . . . . . 197
Belt tensioners . . . . . . . . . . . . . . . . . . 199
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . 250
During pregnancy . . . . . . . . . . . . . . . . 198
Height adjustment . . . . . . . . . . . . . . . 199
Putting on . . . . . . . . . . . . . . . . . . . . . . 197
Safety notes . . . . . . . . . . . . . . . . . . . . . 195
Taking off . . . . . . . . . . . . . . . . . . . . . . . 199
Warning lamp . . . . . . . . . . . . . . . . . . . . 18
Single journey memory . . . . . . . . . . . . . . . 26
Sun roof
Convenience open/close function . . . . 54
Opening and closing . . . . . . . . . . . . . . . 55
Seat heating . . . . . . . . . . . . . . . . . . . . . . . 114
Front (deluxe automatic air conditioner) .
114
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Seat memory . . . . . . . . . . . . . . . . . . . . . . . . 75
Selector lever
Manual release (multitronic®) . . . . . . 168
Selector lever positions . . . . . . . . . . . . . . 163
Service interval display . . . . . . . . . . . . . . . 24
Service position for windscreen wipers . 67
servotronic . . . . . . . . . . . . . . . . . . . . . . . . 225
side assist
Area covered by sensors . . . . . . . . . . 151
Changing settings in the MMI . . . . . . 155
Description . . . . . . . . . . . . . . . . . . . . . 149
How the system works . . . . . . . . . . . . 151
Information and warning modes . . . 151
Messages in instrument cluster display .
156
Sitting position
Driver . . . . . . . . . . . . . . . . . . . . . . . . . .
Front passenger . . . . . . . . . . . . . . . . .
Incorrect sitting position . . . . . . . . . .
Rear passengers . . . . . . . . . . . . . . . . .
188
189
191
189
Ski bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Snow chains . . . . . . . . . . . . . . . . . . . . . . . 273
Sockets
230 Volt . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Spare key . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Starting the engine . . . . . . . . . . . . . . . . 46
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . 277
Spare wheel . . . . . . . . . . . . . . . . . . . . . . . . 284
Speed warning . . . . . . . . . . . . . . . . . . . . . . 28
Speedometer . . . . . . . . . . . . . . . . . . . . . 14, 23
Starting the engine
After fuel tank has been run dry . . . . 252
Jump-starting . . . . . . . . . . . . . . . . . . . 293
Spare key . . . . . . . . . . . . . . . . . . . . . . . . 46
Tow-starting . . . . . . . . . . . . . . . . . . . . 295
Sun blinds . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Supplementary heater
Deluxe automatic air conditioner . . . 101
Deluxe automatic air conditioner plus . . .
110
Suspension control . . . . . . . . . . . . . . . . . 159
Warning lamp . . . . . . . . . . . . . . . . . . . . 39
Switches on driver's door
Central locking system . . . . . . . . . . . . . 49
Switching off the engine . . . . . . . . . 118, 120
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
T
Tailgate
See Boot lid . . . . . . . . . . . . . . . . . . . . . . 51
Tank capacity . . . . . . . . . . . . . . . . . . . . . . 321
Technical data . . . . . . . . . . . . . . . . . . . . . . 320
tiptronic . . . . . . . . . . . . . . . . . . . . . . . 162, 166
Starting with jump leads . . . . . . . . . . . . . 293
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Status messages . . . . . . . . . . . . . . . . . . . . . 30
Total journey memory . . . . . . . . . . . . . . . . 26
Steering . . . . . . . . . . . . . . . . . . . . . . . . . 16, 36
Locking the steering . . . . . . . . . . . . . . 116
Malfunction . . . . . . . . . . . . . . . . . . . . . . 34
Steering wheel height adjustment
(manual) . . . . . . . . . . . . . . . . . . . . . . . 116
Tow-away protection . . . . . . . . . . . . . . . . . 50
Storage compartments . . . . . . . . . . . . . . . 90
Front seats . . . . . . . . . . . . . . . . . . . . . . . 91
Towing bracket
Parking system . . . . . . . . . . . . . . . . . . 177
Towing
Automatic braking . . . . . . . . . . . . . . . . 233
Trailer stabilisation . . . . . . . . . . . . . . . 233
Towing away . . . . . . . . . . . . . . . . . . . . . . . 295
document_0900452a81b1b9de.book Seite 339 Donnerstag, 26. Juli 2007 9:16 09
Index
Towing bracket, removable . . . . . . . . . . . 235
Towing bracket, retrofitting . . . . . . . . . . . 240
Towline anchorage
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . 296
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
Tow-starting . . . . . . . . . . . . . . . . . . . . . . . 297
Traction control system . . . . . . . . . . . . . . 222
Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . .
Notes on towing . . . . . . . . . . . . . . . . .
Points to check before towing . . . . . .
Technical requirements . . . . . . . . . . .
232
235
234
232
232
Tread wear indicators . . . . . . . . . . . . . 270
Tyre pressure monitoring system . 39, 41
Tyre service life . . . . . . . . . . . . . . . . . . 268
Universal transmitter . . . . . . . . . . . . . . . . 179
Unleaded fuel . . . . . . . . . . . . . . . . . . . . . . 251
Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Central locking system . . . . . . . . . . . . . 48
V
Vehicle data sticker . . . . . . . . . . . . . . . . . . 321
Trailer turn signals
Indicator lamp . . . . . . . . . . . . . . . . . . . . 18
Vehicle identification data . . . . . . . . . . . . 321
Vehicle identification number . . . . . . . . . 321
Tread depth . . . . . . . . . . . . . . . . . . . . . . . . 270
Ventilation
Deluxe automatic air conditioner . . . . . 93
Deluxe automatic air conditioner plus . .
101
Trip recorder . . . . . . . . . . . . . . . . . . . . . . . . 14
Ventilation slots . . . . . . . . . . . . . . . . . . . . . 192
Trips, checklist . . . . . . . . . . . . . . . . . . . . . 187
Turn signals . . . . . . . . . . . . . . . . . . . . . . . . . 62
Indicator lamp . . . . . . . . . . . . . . . . . . . . 18
W
Type plate . . . . . . . . . . . . . . . . . . . . . . . . . 321
Warning lamps . . . . . . . . . . . . . . . . . . . . . . 15
Airbag system . . . . . . . . . . . . . . . . . . . . 17
Anti-lock brake system . . . . . . . . . . . . . 19
Brake system . . . . . . . . . . . . . . . . . . . . . 20
Dynamic steering . . . . . . . . . . . . . . . 16, 36
Electro-mechanical parking brake . 19, 20
Electronic stabilisation program . . . . . 17
Emission control system . . . . . . . . . . . . 18
Engine management . . . . . . . . . . . . . . . 16
Tyre Mobility System . . . . . . . . . . . . . . . . 285
Tyre pressure . . . . . . . . . . . . . . . . . 39, 41, 268
Tyre pressure monitoring system . . . . 39, 41
Tyre repair kit . . . . . . . . . . . . . . . . . . . . . . 283
Tyre Mobility System . . . . . . . . . . . . . 285
Tyres
Inflation pressures . . . . . . . . . . . . 39, 268
Run flat tyres . . . . . . . . . . . . . . . . . . . . 274
Controls
Safety
Seat belt . . . . . . . . . . . . . . . . . . . . . . . . . 18
Suspension control . . . . . . . . . . . . . . . . 39
Warning triangle . . . . . . . . . . . . . . . . . . . . 282
Washer fluid level low . . . . . . . . . . . . . . . . . 37
U
Trailer stabilisation . . . . . . . . . . . . . . . . . . 233
Trailer weights
See Performance, weights and
dimensions . . . . . . . . . . . . . . . . . . . . 323
339
Driving tips
Washing the vehicle
By hand . . . . . . . . . . . . . . . . . . . . . . . . . 244
Car wash . . . . . . . . . . . . . . . . . . . . . . . . 244
With high-pressure cleaner . . . . . . . . 244
Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Weights
See Performance, weights and
dimensions . . . . . . . . . . . . . . . . . . . . 323
Wheel bolts . . . . . . . . . . . . . . . . . . . . . . . . 272
Wheel imbalance . . . . . . . . . . . . . . . . . . . . 268
Wheels . . . . . . . . . . . . . . . . . . . . . . . . 246, 268
Changing . . . . . . . . . . . . . . . . . . . . . . . . 288
Changing wheels round . . . . . . . . . . . 270
Window heating . . . . . . . . . . . . . . . . . 98, 106
Windows
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . 246
De-icing . . . . . . . . . . . . . . . . . . . . . . . . . 246
Malfunctions . . . . . . . . . . . . . . . . . . . . . . 55
Windows (electric)
See Electric windows . . . . . . . . . . . . . . . 53
Windscreen washer fluid . . . . . . . . . . . . . 267
Windscreen wiper and washer system . . . 65
Windscreen wipers . . . . . . . . . . . . . . . . . . .
Changing blades . . . . . . . . . . . . . . . . . .
Defective . . . . . . . . . . . . . . . . . . . . . . . . .
Service position . . . . . . . . . . . . . . . . . . .
65
68
39
67
Winter conditions
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . 263
Care of vehicle . . . . . . . . . . . . . . . . . . . 244
General maintenance
Self-help
Technical data
document_0900452a81b1b9de.book Seite 340 Donnerstag, 26. Juli 2007 9:16 09
340
Index
Cooling system . . . . . . . . . . . . . . . . . . 260
Defrosting windows . . . . . . . . . . . 98, 106
De-icing windows . . . . . . . . . . . . . . . . 246
Diesel . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Seat heating (deluxe automatic air
conditioner) . . . . . . . . . . . . . . . . . . . 114
Seat heating for rear seats . . . . . . . . 115
Snow chains . . . . . . . . . . . . . . . . . . . . 273
Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
Windscreen washer . . . . . . . . . . . . . . 267
Winter tyres . . . . . . . . . . . . . . . . . . . . . . . . 272
Wiper blades
See Windscreen wipers . . . . . . . . . . . . 68
X
Xenon lights
Driving abroad . . . . . . . . . . . . . . . . . . . . 59
Download PDF