Sharp | CP-C401E | User`s manual | Sharp CP-C401E User`s manual

GOT812 Series
12.1” XGA/SVGA TFT IP66-rating
Touch Panel Computer
User’s Manual
Disclaimers
This manual has been carefully checked and believed to contain accurate
information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of
patents or any third party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the
accuracy, completeness or usefulness of any information in this document. Axiomtek
does not make any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any
time without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved
May 2013, Version A7
Printed in Taiwan
1. The GOT812L/GOT812LR are compliant by IEC60945, it configures with
GOT812L/GOT812LR, +12VDC power adapter, COM and USB by Keyboad and
Mouse.
Note
ii
2. The GOT812LV series is 9~36V power adapter.
Safety Precautions
Before getting started, please read the following important safety precautions.
1.
The GOT812 Series does not come equipped with an operating system. An
operating system must be loaded first before installing any software into the
computer.
2.
Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in
any static-shielded devices. Most electronic components are sensitive to static
electrical charge.
3.
Disconnect the power cord from the GOT812 Series before any installation. Be
sure both the system and external devices are turned OFF. A sudden surge of
power could ruin sensitive components that the GOT812 Series must be
properly grounded.
4.
The brightness of the flat panel display will be getting weaker as a result of
frequent usage. However, the operating period varies depending on the
application environment.
5.
Turn OFF the system power before cleaning. Clean the system using a cloth
only. Do not spray any liquid cleaner directly onto the screen. The GOT812
Series may come with or w/o a touchscreen. Although t he touchscreen is
chemical resistant, it is recommended that you spray the liquid cleaner on a
cloth first before wiping the screen. In case your system comes without the
touchscreen, you must follow the same procedure and not spray any cleaner on
the flat panel directly.
6.
Avoid using sharp objects to operate the touchscreen. Scratches on the
touchscreen may cause malfunction or internal failure to the touchscreen.
7.
The flat panel display is not susceptible to shock or vibration. W hen assembling
the GOT812 Series, make sure it is securely installed.
8.
Do not open the system ’s back cover. If opening the cover for maintenance is a
must, only a trained technician is allowed to do so. Integrated circuits on
computer boards are sensitive to static electricity. To avo id damaging chips
from electrostatic discharge, observe the following precautions:
 Before handling a board or integrated circuit, touch an unpainted portion of
the system unit chassis for a few seconds. This will help to discharge any
static electricity on your body.
 When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
iii
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd. IBM, PC/AT, PS/2, VGA are
trademarks of International Business Machines Corporation.
Intel
®
and Atom ™ are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation. Other brand names and
trademarks are the properties and registered brands of their respective owners .
iv
Table of Contents
Disclaimers..................................................................................................... ii
Safety Precautions ........................................................................................ iii
CHAPTER 1 INTRODUCTION ..............................................................1
1.1
1.2
General Description ............................................................................. 1
Specifications ....................................................................................... 2
1.2.1 Main CPU Board ................................................................................................... 2
1.2.2 I/O System ............................................................................................................ 2
1.2.3 System Specification............................................................................................. 3
1.3
1.4
1.5
Dimensions ........................................................................................... 4
I/O Outlets ............................................................................................. 6
Package List ......................................................................................... 7
CHAPTER 2 System Configurations .................................................9
2.1
I/O Pin Assignment ............................................................................. 10
2.1.1 Serial Port Interface .......................................................................................... 10
2.1.2 Ethernet ............................................................................................................ 11
2.2
Water-proof Cables ............................................................................ 12
2.2.1
2.2.2
2.2.3
2.2.4
2.2.5
2.3
Power cable ...................................................................................................... 12
Power adapter for GOT812L/GOT812LR ......................................................... 13
Power description for GOT812LV series .......................................................... 13
COM .................................................................................................................. 15
USB cables ....................................................................................................... 16
Mounting Method................................................................................ 16
2.3.1 VESA mounting ................................................................................................. 16
2.3.2 VESA-ARM Mounting........................................................................................ 17
2.3.3 Suspension Mounting ....................................................................................... 18
2.4
Keyboard Kit ....................................................................................... 20
CHAPTER 3 AMI BIOS SETUP UTILITY......................................... 23
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Starting ................................................................................................ 23
Navigation Keys .................................................................................. 23
Main Menu ........................................................................................... 24
Advanced Menu .................................................................................. 25
PCI PnP Menu ..................................................................................... 38
Boot Menu ........................................................................................... 41
Security Menu ..................................................................................... 46
Chipset Menu ...................................................................................... 48
Exit Menu ............................................................................................ 53
CHAPTER 4 DRIVERS INSTALLATION.......................................... 55
4.1
4.2
System ................................................................................................. 55
Touch Screen ...................................................................................... 56
4.2.1 Specification ...................................................................................................... 56
v
4.2.2 Driver Installation- Windows XP ....................................................................... 57
4.3
Embedded O.S........................................................................... 59
4.3.1 Windows XP Embedded ................................................................................... 59
vi
GOT812 Series User’s Manual
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications of the GOT812 Series.
Chapter 1 includes the following sections:

General Description

Specification

Dimensions

I/O Outlets

Package List
1.1
General Description
The GOT812 Series is a fan-less and compact-size touch panel computer, equipped
with a 12.1” High brightness TFT LCD display and low power consumption Intel ○R
TM
Atom
N270 1.6GHz processor with FSB 533MHz. The GOT812 Series supports
®
®
®
®
W indows XP, W indows 7, W indows CE.NET and W indows XP embedded. The
panel computer is able to install a CompactFlash ™ and provided a Mini card slot for
extension such as W IFI. Its excellent ID and friendly user interface make it a
professional yet easy-to-use panel computer. The GOT812 Series is an ideal for
space-limited applications in factory automation, machine maker operating systems,
building automation, and more.

GOT812 Series: 12.1” TFT XGA/SVGA Fanless Touch Panel Computer

Reliable and Stable Design
The GOT812 Series adopts a fanless cooling system and a
CompactFlash ™ , which makes it suitable for vibration environments,
example for Marine and Crane.

Embedded O.S. Supported
The GOT812 Series not only supports W indows® XP and W indows® 7, but
also supports embedded OS, such as W indows® CE.NET, and W indows®
XP embedded. For storage device, the GOT812 Series supports
CompactFlash™ and 2.5” SSD device.

Industrial-grade Product Design
The GOT812 Series has an incredible design to be used in different
industrial environments.

The whole enclasure meets the IP66 standard.

For connecting other devices, the GOT812 Series also features several
interfaces: USB, Ethernet, and RS-232/422/485.
Introduction
1
GOT812 Series User’s Manual
1.2
Specifications
1.2.1 Main CPU Board

CPU


N270 1.6GHz processor with FSB 533MHz onboard
945GSE + ICH7M
BIOS


TM
System Chipset



Intel Atom
America Megatrends BIOS
System Memory

One 200-pin DDR2 SO-DIMM socket

Maximum memory up to 2GB
1.2.2 I/O System


Standard I/O

One RS-232 and one RS-232/422/485

USB 2.0 x 2 (M12 connector)
Ethernet


Expansion


2
One RTL81111b Gigabit Ethernet
One Mini PCI-E card
Storage

One CF slot

One SATA interface
Introduction
GOT812 Series User’s Manual
1.2.3 System Specification

12.1” TFT LCD

GOT812L/GOT812LV: 12.1” SVGA 450nits

GOT812LR: 12.1” XGA 1000nits

Heat Dispensing Design

Disk drive housing:


Net Weight


-20℃ to 55℃
Relative Humidity


296mm x 240mm x 59mm
Operation Temperature


4.6 Kgs (3.52 lb)
Dimension (Main Body Size)


One 2.5” SATA drive (optional)
10% to 90% @ 40℃, Non-Condensing
Vibration

5 to 500 Hz, 3.0 G for CF card

5 to 500 Hz, 2.0 G for SSD
1. All specifications and images are subject to change without notice.
Note
2. The GOT812 series is suited on serious environment; please choose the wide
temperature DRAM and SSD.
Warning: According the warrantee is adopt for the IP66 guarantee, please choose CF,SSD
and RAM by Axiomtek, also please kindly don’t disassemble the system by
youself.
Introduction
3
GOT812 Series User’s Manual
1.3
Dimensions
This diagram shows you dimensions and outlines of the GOT812 Series.
4
Introduction
GOT812 Series User’s Manual
Introduction
5
GOT812 Series User’s Manual
1.4
I/O Outlets
Please refer to the following illustration for I/O locations of the GOT812 Series.
No
6
Function
1
Backlight ON/OFF
2
Brightness Adjust
3
Power Switch(ATX)
4
DC power connector
5
COM1(configure RS422/485)
6
COM2
7
Ethernet
8
USB2.0 × 2
Introduction
GOT812 Series User’s Manual
1.5
Package List
When you receive the GOT812 Series, the bundled package should contain the following
items:

GOT812 x 1

Driver CD x1

DC cable x1

Power Adapter (optional)

Water-proof cables (optional)

VESA ARM(optional)

Suspension Kit (optional)

Keyboard Bracket Kit (optional)

IP54 Keyboard(optional)
If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.
Introduction
7
GOT812 Series User’s Manual
This page is intentionally left blank.
8
Introduction
GOT812 Series User’s Manual
CHAPTER 2
System Configurations
The GOT812 Series provides rich I/O ports and flexible expansions for you to meet
different demand, for example, CF. The chapter will show you how to install the
hardware. It includes:

I/O Pin Assignment

Hard Disk and DRAM

Wireless LAN Card (Optional)

Water-proof cables (Optional)

Hanging and VESA mounting (Optional)
System Configurations
9
GOT812 Series User’s Manual
2.1
I/O Pin Assignment
The GOT812 Series has two serial ports, COM1 (RS-232/ 422/ 485) and COM2 (RS232), Ethernet, USB, and DC-in 12V/24V connecter.
2.1.1 Serial Port Interface
The following table shows you the pin assignments of this connector :
Pin
Signal
Pin
Signal
1
Data Carrier Detect (DCD)
6
Data Set Ready (DSR)
2
Receive Data (RXD)
7
Request To Send (RTS)
3
Transmit Data (TXD)
8
Clear To Send (CTS)
4
Data Terminal Ready (DTR)
9
Ring Indicator (RI)
5
Ground (GND)
In addition, COM1 can be set for RS-232/422/485 by jumper. The jump setting is
listed as below:
COM1
JP11
JP12
JP13
RS-232 (default)
3-5, 4-6
3-5, 4-6
1-2
RS-422
1-3, 2-4
1-3, 2-4
3-4, 7-8
RS-485
1-3, 2-4
1-3, 2-4
5-6, 7-8
10
System Configurations
GOT812 Series User’s Manual
W hen COM1 is set to RS-422 or RS-485, the pin assignments are listed below:
Signal Name
Pin
RS-422
RS-485
1
TX-
DATA-
2
TX+
DATA+
3
RX+
No connector
4
RX-
No connector
5
No connector
No connector
6
No connector
No connector
7
No connector
No connector
8
No connector
No connector
9
GND
GND
2.1.2 Ethernet
The GOT812 Series is equipped with a high performance Plug and Play Ethernet interface, full
compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector.
Please refer to detailed pin assignment list below:
Pin
Signal
1
TX+ (Data transmission positive
2
TX- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ45 termination
5
RJ45 termination
6
Rx- (Data reception negative)
7
RJ45 termination
8
RJ45 termination
1 2 3 4 5 6 7 8
RJ-45
System Configurations
11
GOT812 Series User’s Manual
2.2
Water-proof Cables
GOT-800 series uses specific M12 connector for water-proof.
order each cable base on application.
Therefore you will
There are four kind cables of GOT812, by the optional, if you will apply the USB,
COM or Etherent then you can select a cable for the package .
The Power cable included in the accessory box, when you will need the power
adapter, also it can be sesected by optional.
2.2.1 Power cable
Please follow pin assignement for the power input.
Pin
V+
Signal
DC 12V or 24V power input
Earth Ground
GND
GND
GND
GND
12
System Configurations
GOT812 Series User’s Manual
2.2.2 Power adapter for GOT812L/GOT812LR
If you order the power adapter, you should choose the power cord type for your
location. The power adapter is +12VDC(5A), 110-240V which is combined M12
connector.
2.2.3 Power description for GOT812LV series
The GOT812LV series is equipped with a vehicle standard power board .
In order to ensure the vehicle could provide a stable DC power, GOT812LV series will detect
the DC power from source is higher than the Start Voltage or not.
System Configurations
13
GOT812 Series User’s Manual
1
Feature:
1.1 DC to DC , 12Voutput, switching mode power supply for vehicle use , it
equips with surge stopper to protect loads from high voltage transients .
2
Power Input:
2.1 Voltage Input Range: 9~36Vdc (Typical: 12Vdc, and 24 Vdc)
2.2 Efficiency: 90% Min. with full loading at 24Vdc input.
2.3 Quiescence Consumption: 0.8W max. W ithout loading.
2.4 Power Input Protection: FUSE, OVP, UVP and
Reversepolarity protection.
3
4
Power Output:
Output
Nominal
Regulation
Ripple/Noise
Min
Max
1
+12V
±5%
120mV
~0.0A
6.0A
Output Protection :
4.1 Short circuit/overloading protection: W hen output is shorted to GND or
exceed
20~30% output power rating, the power supply will cease the output and
recover
Automatically after removal of the short circuit or overloading condition, no
need to reset input power supply.
4.2 Over voltage protection: W hen output voltage exceeds than 10% of rating
that
Causes by PCB abnormal internally, the output will work intermittently that is
so-called latch off mode.
14
System Configurations
GOT812 Series User’s Manual
5
Environment Specification:
5.1 Temperature:
Operating: -25°C to 70°C : Max. output 72W at 45°C ; 36 W at 70°C.
Storage: -40°C to 80°C
5.2 Humidity:
Operating: 10% to 90% RH
Storage: 5% to 95% RH
5.3 Altitude:
Operating properly from sea level to 10000 feet.
2.2.4 COM
There are two COM cables which are combined M12 connector. Also, you can refer
2.1.1 for the Series port pin assignement.
System Configurations
15
GOT812 Series User’s Manual
2.2.5 USB cables
The USB cable is combined M12 connector for water-proof. It is extended two USB
ports for applicaton.
2.3
Mounting Method
There are two mounting ways for the GOT812 Series. One is suspension, the other is
VESA mount.
2.3.1 VESA mounting
The GOT812 can accept both VESA 75 and VESA 100.
VESA 100
VESA 75
16
System Configurations
GOT812 Series User’s Manual
2.3.2 VESA-ARM Mounting
Step 1
Find out the 4 screws as marked on the back side of chassis.
Step 2 Assemble the VESA-ARM to the back side of the chassis, and fix the
screws.
Step 3
VESA mounting Installation completed.
System Configurations
17
GOT812 Series User’s Manual
2.3.3 Suspension Mounting
Step 1
Find out the 2 handle and a suspension holder in the package.
Step 2
Assemble the handle to the right and left side of the holder, and fix the screws.
18
System Configurations
GOT812 Series User’s Manual
Step 3 Suspension mounting Installation completed.
System Configurations
19
GOT812 Series User’s Manual
2.4
Keyboard Kit
Step 1
Find out the IP54 keyboard, a chassis and 4 screws in the package.
Step 2
Assemble the chassis to the right and left side of back cover, and fix the
screws.
20
System Configurations
GOT812 Series User’s Manual
Step 3
Keyboard mounting Installation completed.
System Configurations
21
GOT812 Series User’s Manual
This page is intentionally left blank.
22
System Configurations
GOT812 Series User’s Manual
CHAPTER 3
AMI BIOS SETUP UTILITY
This chapter provides users with detailed description how to set up basic system
configuration through the AMI BIOS setup utility.
3.1
Starting
To enter the setup screens, follow the steps below:
1.
Turn on the computer and press the <Del> key immediately.
2.
After you press the <Delete> key, the main BIOS setup menu displays. You can access
the other setup screens from the main BIOS setup menu, such as the Chipset and
Power menus.
3.2
Navigation Keys
The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS
setup utility hot keys can be used at any time during the setup navigation process.
These keys include <F1>, <F10>, <Enter>, <ESC>, <Arrow> keys, and so on.
Some of navigation keys differ from one screen to another.
Note
 Left/Right
The Left and Right <Arrow> keys allow you to select a setup screen.
 Up/Down
The Up and Down <Arrow> keys allow you to select a setup screen or subscreen.
+ Plus/Minus
The Plus and Minus <Arrow> keys allow you to change the field value of a
particular setup item.
Tab
The <Tab> key allows you to select setup fields.
F1
The <F1> key allows you to display the General Help screen.
F10
The <F10> key allows you to save any changes you have made and exit
Setup. Press the <F10> key to save your changes.
Esc
The <Esc> key allows you to discard any changes you have made and exit
the Setup. Press the
<Esc> key to exit the setup without saving your changes.
Enter
The <Enter> key allows you to display or change the setup option listed for a
particular setup item. The <Enter> key can also allow you to display the setup
sub- screens.
AMI BIOS Setup Utility
23
GOT812 Series User’s Manual
3.3
Main Menu
W hen you first enter the Setup Utility, you will enter the Main setup screen. You can
always return to the Main setup screen by selecting the Main tab. There are two Main
Setup options. They are described in this section. The Main BIOS Setup screen is
shown below.

System Time/Date
Use this option to change the system time and date. Highlight System Time
or System Date using the <Arrow> keys. Enter new values through the
keyboard. Press the <Tab> key or the <Arrow> keys to move between fields.
The date must be entered in MM/DD/YY format. The time is entered in
HH:MM:SS format.
24
AMI BIOS Setup Utility
GOT812 Series User’s Manual
3.4
Advanced Menu
The Advanced menu allows users to set configuration of the CPU and other system
devices. You can select any of the items in the left frame of the screen to go to the
sub menus:

CPU Configuration

IDE Configuration

SuperIO Configuration

Hardware Health Configuration

ACPI Configuration

APM Configuration

MPS Configuration

PCI Express Configuration

USB Configuration
For items marked with “”, please press <Enter> for more options.
AMI BIOS Setup Utility
25
GOT812 Series User’s Manual

Configure advanced CPU settings
This screen shows the CPU Configuration, and you can change the value of the
selected option.

Max CPUID Value Limit
You can enable this item to let legacy operating systems boot even without
support for CPUs with extended CPU ID functions.

Execute-Disable Bit Capability
This item helps you enable or disable the No-Execution Page Protection
Technology.

Hyper Threading Technology
Use this item to enable or disable Hyper -Threading Technology, which
makes a single physical processor perform multi -tasking function as two
logical ones.

Intel (R) SpeedStep (tm) tech
This item helps you enable or disable the Intel SpeedStep Technology.

Intel (R) C-STATE tech
Use this item to enable or disable the C -State technology.
26
AMI BIOS Setup Utility
GOT812 Series User’s Manual

Enhanced C-States
This item allows you to enable or disable any available enhanced C-states
(C1E, C2E, C3E, C4E and Hard C4E).

IDE Configuration
You can use this screen to select options for the IDE Configuration, and change the
value of the selected option. A description of the selected item appears on the right
side of the screen. For items marked with “”, please press <Enter> for more
options.

ATA/IDE Configuration
Use this item to specify the integrated IDE controller. There are three
options for your selection: Disabled, Compatible and Enhanced.

Legacy IDE Channels
W hen the ATA/IDE Configuration is set to Compatible, this item will be
displayed.

Primary/Secondary/Third IDE Master/Slave
Select one of the hard disk drives to configure IDE devices installed in the
system by pressing <Enter> for more options .
AMI BIOS Setup Utility
27
GOT812 Series User’s Manual

SuperIO Configuration
You can use this screen to select options for the SuperIO Configuration, and change
the value of the selected option. A description of the selected item appears on the
right side of the screen.

Serial Port1 Address
This item specifies the base I/O port address and Interrupt Request address
of serial port 1. The Optimal setting is 3F8/IRQ4. The Fail-Safe default
setting is 3F8.

Serial Port1 IRQ
This item specifies the IRQ used by the serial port 1.

Serial Port2 Address
This item specifies the base I/O port address and Interrupt Request address
of serial port 2. The Optimal setting is 2F8/IRQ3. The Fail-Safe setting is
2F8.

Serial Port2 IRQ
This item specifies the IRQ used by the serial port 2.

Serial Port3 Address
This item specifies the base I/O port address and I nterrupt Request address
of serial port 3.
28
AMI BIOS Setup Utility
GOT812 Series User’s Manual

Serial Port3 IRQ
This item specifies the IRQ used by the serial port 3.

Serial Port4 Address
This item specifies the base I/O port address and Interrupt Request address
of serial port 4.

Serial Port4 IRQ
This item specifies the IRQ used by the serial port 4.

Hardware Health Configuration
This screen shows the Hardware Health Configuration, and a description of the
selected item appears on the right side of the screen.

System Temperature/CPU Temperature
These items display the temperature of CPU and System, Vcore, etc.
AMI BIOS Setup Utility
29
GOT812 Series User’s Manual

ACPI Settings
You can use this screen to select options for the ACPI Settings, and change the
value of the selected option. A description of the selected item appears on the right
side of the screen.
30
AMI BIOS Setup Utility
GOT812 Series User’s Manual

APM Configuration
You can use this screen to select options for the APM Configuration, and change the
value of the selected option. A description of the selected item appears on the right
side of the screen.

Power Management/APM
Set this item to allow Power Management/APM support. The default setting
is Enabled.
Disabled
Set this item to prevent the chipset power management and APM (Advanced Power
Management) features.
Enabled
Set this item to allow the chipset power management and APM (Advanced Power
Management) features. This is the default setting.
AMI BIOS Setup Utility
31
GOT812 Series User’s Manual

Video Power Down Mode
This option specifies the Power State that the video subsystem enters when
the BIOS places it in a power saving state after the specified period of
display inactivity has expired. The default setting is Suspend.
Disabled
This setting prevents the BIOS from initiating any power saving modes concerned with
the video display or monitor.
Suspend
This option places the monitor into suspend mode after the specified period of display
inactivity has expired. This means the monitor is not off. The screen will appear blacked
out. The standards do not cite specific power ratings because they vary from monitor to
monitor, but this setting use less power than Standby mode. This is the default setting.

Hard Disk Drive Power Down Mode
This option specifies the power conserving state that the hard disk drive
enters after the specified period of hard drive inactivity has expired . The
default setting is Suspend.
Disabled
This setting prevents hard disk drive power down mode.
Suspend
This option cuts the power to the hard disk drives during a system suspend. This is the
default setting.

Suspend Time Out (Minute)
This option specifies the length of time the system waits before it enters
suspend mode. The default setting is Disabled.
Disabled
This setting prevents the system from entering suspend mode. This is the default
setting.
1 Min
Set this item to allow the computer system to enter suspend mode after being inactive
for 1 minute.
4 Min
Set this item to allow the computer system to enter suspend mode after being inactive
for 4 minutes.
10 Min
Set this item to allow the computer system to enter suspend mode after being inactive
for 10 minutes.

Throttle Slow Clock Ratio
Use this item to specify the speed of the system clock when running the
power saving states.
32
AMI BIOS Setup Utility
GOT812 Series User’s Manual

Power Button Mode
This option specifies how the externally mounted power button on the front
of the computer chassis is used. The default setting is On/Off.
On/Off
Pushing the power button turns the computer on or off. This is the default setting. This
is the default setting.
Suspend
Pushing the power button places the computer in Suspend mode or Full On power
mode.

*** Advanced Resume Event Controls ***

Resume On Ring
This item enables or disables the function of Resume On Ring that resumes
the system through incoming calls.

Resume On RTC Alarm
You can set “Resume on RTC Alarm” item to enabled and key in Data/time
to power on system.
AMI BIOS Setup Utility
33
GOT812 Series User’s Manual

MPS Configuration
This screen shows the MPS (Multi Processor Specification) Configuration, and you
can change its value. A description of the selected item appears on the right side of
the screen.

MPS Revision
Use this item to select MPS (Multi Processor Specification) Revision 1.1 or
1.4. The default setting is 1.4.
34
AMI BIOS Setup Utility
GOT812 Series User’s Manual

PCI Express Configuration
This screen shows the PCI Express Configuration, and you can change its value. A
description of the selected item appears on the right side of the screen.

Active State Power-Management
Use this item to enable or disable the function of Active State Power Management to provide you with lower power consumption. The default
setting is Disabled
AMI BIOS Setup Utility
35
GOT812 Series User’s Manual

SB PCIE Ports Configuration
Scroll to this item and press <Enter> to view th e SB PCIE Ports Configuration sub
menu, which contains several options for your configuration.
36
AMI BIOS Setup Utility
GOT812 Series User’s Manual

USB Configuration
You can use this screen to select options for the USB Configuration, and change the
value of the selected option. A description of the selected item appears on the right
side of the screen.

Legacy USB Support
Use this item to enable or disable support for USB device on legacy
operating system. The default setting is Enabled.

USB 2.0 Controller Mode
Use this item to configure the USB 2.0 controller. The default setting is
HiSpeed.

BIOS EHCI Hand-Off
Enabling this item provides the support for operating systems without an
EHCI hand-off feature. The default setting is Enabled.
AMI BIOS Setup Utility
37
GOT812 Series User’s Manual
3.5
PCI PnP Menu
The PCI PnP menu allows users to change the advanced settings for PCI/PnP devices.
(1)
38
AMI BIOS Setup Utility
GOT812 Series User’s Manual
(2)

Clear NVRAM
Use this item to clear the data in the NVRAM (CMOS). Here are the options
for your selection, No and Yes.

Plug & Play O/S
W hen the setting is No, Use this item to configure all the device s in the
system. W hen the setting is Yes and if you install a Plug and Play operating
system, the operating system configures the Plug and Play devices not
required for boot. The default setting is No.

PCI Latency Timer
This item controls how long a PCI device can hold the PCI bus before
another takes over. The longer the latency, the longer the PCI device can
retain control of the bus before handing it over to another PCI device. There
are several options for your selection.

Allocate IRQ to PCI VGA
This item allows BIOS to choose an IRQ to assign for the PCI VGA card.
Here are the options for your selection, No and Yes.
AMI BIOS Setup Utility
39
GOT812 Series User’s Manual

Palette Snooping
Some old graphic controllers need to “snoop” on the VGA palette, and then
map it to their display as a way to provide boot information and VGA
compatibility. This item allows such snooping to take place. Here are the
options for your selection, Disabled and Enabled.

PCI IDE BusMaster
This item is a toggle for the built-in driver that allows the onboard IDE
controller to perform DMA (Direct Memory Access) transfer. Here are the
options for your selection, Disabled and Enabled.

OffBoard PCI/ISA IDE Card
This item is for any other non-onboard PCI/ISA IDE controller adapter.
There are several options for your selection.

IRQ3/4/5/7/9/10/11/14/15
These items will allow you to assign each system interrupt a type,
depending on the type of device using the interrupt. The option “Available”
means the IRQ is going to assign automatically. Here are the options for
your selection, Available and Reserved.

DMA Channel 0/1/3/5/6/7
These items will allow you to assign each DMA channel a type, depending
on the type of device using the channel. The option “Available” means the
channel is going to assign automatically. Here are the options for your
selection, Available and Reserved.
40
AMI BIOS Setup Utility
GOT812 Series User’s Manual
3.6
Boot Menu
The Boot menu allows users to change boot options of the system. You can select
any of the items in the left frame of the screen to go to the sub menus:

Boot Settings Configuration

Boot Device Priority

Removable Drives

Lan Boot Settings Configuration
For items marked with “”, please press <Enter> for more options.
AMI BIOS Setup Utility
41
GOT812 Series User’s Manual

Boot Settings Configuration

Quick Boot
Enabling this item lets the BIOS skip some po wer on self tests (POST). The
default setting is Enabled.

Quiet Boot
Disabled
Set this item to allow the computer system to display the POST messages.
Enabled
Set this item to allow the computer system to display the OEM logo. This is the
default setting.

AddOn ROM Display Mode
This item selects the display mode for option ROM. The default setting is
Force BIOS.

Boot Num-Lock
Use this item to select the power-on state for the NumLock. The default
setting is On.
42
AMI BIOS Setup Utility
GOT812 Series User’s Manual

PS/2 Mouse Support
This item determines if the BIOS should reserve IRQ12 for the PS/2 mouse
or allow other devices to make use of this IRQ. Here are the options for your
selection, Auto, Enabled and Disabled.

Wait For ‘F1’ If Error
If this item is enabled, the system waits for the F1 key to be pressed when
error occurs. The default setting is Enabled.

Hit ‘DEL’ Message Display
If this item is enabled, the system displays the message “Press DEL to run
Setup” during POST. The default setting is Enabled.

Boot Device Priority
The Boot Device Priority screen specifies the the boot device priority sequence from
the available devices.
AMI BIOS Setup Utility
43
GOT812 Series User’s Manual

Removable Drives
Use this screen to view the removable drives in the system. The BIOS will attempt to
arrange the removable drive boot sequence automatica lly. You can also change the
booting sequence.
44
AMI BIOS Setup Utility
GOT812 Series User’s Manual

Lan Boot Settings Configuration
The Lan Boot Settings Configuration can enable or disable Lan Boot ROM to allow
the system Ooot on LAN.
AMI BIOS Setup Utility
45
GOT812 Series User’s Manual
3.7
Security Menu
The Security menu allows users to change the security settings for the system.

Supervisor Password
This item indicates whether a supervisor password has been set. If the
password has been installed, Installed displays. If not, Not Installed displays.

User Password
This item indicates whether a user password has been set. If the password
has been installed, Installed displays. If not, Not Installed displays.

Change Supervisor Password
Select this option and press <Enter> to access the sub menu. You can use
the sub menu to change the supervisor password.

Change User Password
Select this option and press <Enter> to access the sub menu. You can use
the sub menu to change the user password.
46
AMI BIOS Setup Utility
GOT812 Series User’s Manual

Boot Sector Virus Protection
This option is near the bottom of the Security Setup screen. The default
setting is Disabled.
Disabled
Set this item to prevent the Boot Sector Virus Protection. This is the default setting.
Select Enabled to enable boot sector protection. It displays a warning when any
program (or virus) issues a Disk Format command or attempts to write to the boot
sector of the hard disk drive. If enabled, the following appears when a write is
attempted to the boot sector. You may have to type N several times to prevent the
boot sector write.
Boot Sector Write!
Enabled
Possible VIRUS: Continue (Y/N)? _
The following appears after any attempt to format any cylinder, head, or sector of
any hard disk drive via the BIOS INT 13 Hard disk drive Service:
Format!!!
Possible VIRUS: Continue (Y/N)?
AMI BIOS Setup Utility
47
GOT812 Series User’s Manual
3.8
Chipset Menu
The Chipset menu allows users to change the advanced chipset settings. You can
select any of the items in the left frame of the screen to go to the sub menus:

North Bridge Configuration

South Bridge Configuration
For items marked with “”, please press <Enter> for more options.
48
AMI BIOS Setup Utility
GOT812 Series User’s Manual

North Bridge Configuration

DRAM Frequency
This item allows you to control the Memory Clock.

Configure DRAM Timing by SPD
This item can enable or disable DRAM timing by SPD (Serial Presence
Detect) device, which is a small EEPROM chip on the memory module,
containing important information about the module speed, size, addressing
mode and various parameters.

Boot Graphic Adapter Priority
This item allows you to select the graphics controller as the primary boot
device.

Internal Graphics Mode Select
This item allows you to select the amount of system memory used by the
internal graphics device.
AMI BIOS Setup Utility
49
GOT812 Series User’s Manual

Video Function Configuration
Press <Enter> for the sub-menu for setting up video function.
50
AMI BIOS Setup Utility
GOT812 Series User’s Manual

South Bridge Configuration
(1)
AMI BIOS Setup Utility
51
GOT812 Series User’s Manual
(2)

USB Function
This item allows you to enable or disable USB function.

USB 2.0 Controller
This item allows you to enable or disable the USB 2.0 controller.

Audio Controller
This item allows you to enable or disable the audio support.

SLP_S4# Min. Assertion Width
This item allows you to set the SLP_S4# Assertion W idth.

Restore on AC Power Loss
This item can control how the PC will behave once power is restored
following a power outage, or other unexpected shutdown.

PCIE Port Configuration
This item allows you to set or disable the PCI Express Port s
52
AMI BIOS Setup Utility
GOT812 Series User’s Manual
3.9
Exit Menu
The Exit menu allows users to load your system configuration with optim al or failsafe
default values 0

Save Changes and Exit
W hen you have completed the system configuration changes, select this
option to leave Setup and reboot the computer so the new system
configuration parameters can take effect. Select Save Changes and Exit
from the Exit menu and press <Enter>. Select Ok to save changes and exit.

Discard Changes and Exit
Select this option to quit Setup without making any permanent changes to
the system configuration. Select Discard Changes and Exit from the Exit
menu and press <Enter>. Select Ok to discard changes and exit.
AMI BIOS Setup Utility
53
GOT812 Series User’s Manual

Discard Changes
Use this item to abandon all changes.

Load Optimal Defaults
It automatically sets all Setup options to a complete set of default settings
when you select this option. The Optimal settings are designed for maximum
system performance, but may not work best for all computer applications. In
particular, do not use the Optimal Setup options if your computer is
experiencing system configuration problems. Select Load Optimal Defaults
from the Exit menu and press <Enter>.

Load Fail-Safe Defaults
It automatically sets all Setup options to a complete set of default settings
when you select this option. The Fail-Safe settings are designed for
maximum system stability, but not maximum performance. Select the FailSafe Setup options if your computer is experiencing system configuration
problems.
Select Load Fail-Safe Defaults from the Exit menu and press <Enter>.
Select Ok to load Fail-Safe defaults.
54
AMI BIOS Setup Utility
GOT812 Series User’s Manual
CHAPTER 4
DRIVERS INSTALLATION
4.1
System
GOT812 Series supports Windows 2000/XP. To facilitate the installation of system driver,
please carefully read the instructions in this chapter before start installing.
1. Insert Driver CD and select the “\GOT812 Series\Driver\XP”.
2. Select all files and follow the installing procedure.
Drivers Installation
55
GOT812 Series User’s Manual
4.2
Touch Screen
The GOT812 uses the 5-wire analog resistve. There are the specification and driver
installation which are listed below.
4.2.1 Specification
Touch Screen
5-wire Analog Resistive type
PenMount 6000 USB
Touch Screen Controller
Touch Screen Controller IC
Communications
USB interface
Baud Rate
19200 baud rate fixed
Resolution
1024 x 1024 (10 bit A/D converter inside)
Power Input
5V
Power Consumption
Active: 24.6mA / Idle Mode: 13.4mA
56
Drivers Installation
GOT812 Series User’s Manual
4.2.2 Driver Installation- Windows XP
The GOT812 Series provides a touch screen driver that users can install it under the
operating system W indows XP. To facilitate installation of the touch screen driver,
you should read the instructions in this chapter carefully before you attempt
installation.
1.
Insert Driver CD and follow the path to select the “\ Driver\XP\Step 5 - Touch”.
2.
Follow the installing procedure and press OK.
3.
lick Start menu and select “PenMount Utilities”; and then, a “PenMount Control Panel”
pops out.
Drivers Installation
57
GOT812 Series User’s Manual
4
Select the “Standard Calibrate” tab.
5
Calibration:
To adjust the display with touch panel, click “Calibration” and follow the calibrate point to
do calibration; there are five points on screen for calibration.
6
58
Press OK.
Drivers Installation
GOT812 Series User’s Manual
4.3
Embedded O.S.
The GOT812 provides the W indows XP Embedded. The O.S. is supported devices
which are listed below.
4.3.1 Windows XP Embedded
Here are supported onboard devices:

Onboard Multi I/O

SATA Hard Drive

USB

PS2 Keyboard and mouse

CRT/LCD display(Default 18bits Resolution 800x600)

10/100/1000 base-T Ethernet

Compact Flash

Onboard Audio

Touch Screen
Drivers Installation
59
GOT812 Series User’s Manual
This page is intentionally left blank.
60
Drivers Installation
Download PDF

advertising