Directed Electronics | 417 | Model 417 Owner`s Guide

Model 417 Owner`s Guide
Model 417
Owner’s Guide
Limited Lifetime
Consumer Warranty
Directed Electronics, Inc. ("DEI®") promises to the original purchaser to repair or
replace with a comparable reconditioned model any DEI unit (hereafter the "unit"),
excluding without limitation the siren, the remote transmitters, the associated
sensors and accessories, which proves to be defective in workmanship or material
under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized
DEI dealer; the unit will be professionally reinstalled in the vehicle in which it was
originally installed by an authorized DEI dealer; and the unit is returned to DEI, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase
bearing the following information: consumer's name, telephone number and address;
the authorized dealers name, telephone number and address; complete product
description, including accessories; the year, make and model of the vehicle; vehicle
license number and vehicle identification number. All components other than the
unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of
the same. This warranty is non-transferable and is automatically void if: the original
purchaser has not completed the warranty card and mailed it within ten (10) days of
the date of purchase to the address listed on the card; the unit's date code or serial
number is defaced, missing or altered; the unit has been modified or used in a
manner contrary to its intended purpose; the unit has been damaged by accident,
unreasonable use, neglect, improper service, installation or other causes not arising
out of defects in materials or construction. The warranty does not cover damage to
the unit caused by installation or removal of the unit. DEI, in its sole discretion, will
determine what constitutes excessive damage and may refuse the return of any unit
with excessive damage. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED
WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE
AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE
EXPRESSLY EXCLUDED; AND DEI NEITHER ASSUMES NOR AUTHORIZES ANY PERSON
OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DEI DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY
FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS
OR INSTALLERS. DEI SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS
AGAINST POSSIBLE THEFT. DEI IS NOT OFFERING A GUARANTEE OR INSURANCE
AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER,
INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VAN-
© 2000 Directed Electronics, Inc.
i
DALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE,
REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF
ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DEI OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF
CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL
APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM
AGAINST DEI SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DEI DEALER'S PURCHASE PRICE OF THE UNIT. DEI SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS,
COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO
REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do
not allow limitations on how long an implied warranty will last or the exclusion or
limitation of incidental or consequential damages. This warranty gives you specific
legal rights and you may also have other rights that vary from State to State.
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your
authorized DEI dealer for details of the plan or call DEI Customer Service at 1-800876-0800. DEI security systems, including this unit, are deterrents against possible
theft. DEI is not offering a guarantee or insurance against vandalism, damage or theft
of the automobile, its parts or contents; and hereby expressly disclaims any liability
whatsoever, including without limitation, liability for theft, damage and/or vandalism.
DEI does not and has not authorized any person or entity to create for it any other
obligation, promise, duty or obligation in connection with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
■
■
■
■
■
■
■
■
■
ii
Date of purchase
Your full name and address
Authorized dealer's company name and address
Type of alarm installed
Year, make, model and color of the automobile
Automobile license number
Vehicle identification number
All security options installed on automobile
Installation receipts
© 2000 Directed Electronics, Inc.
Table of Contents
Limited Lifetime Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
What Is Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Your Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FCC/ID Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Using Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disarming Without a Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Panic Mode (Optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Trunk Access While the System is Armed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Remote Valet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Nuisance Prevention® Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Arming Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Disarming Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table of Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Programming Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Security and Convenience Expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Quick Reference Guide (Removable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
© 2000 Directed Electronics, Inc.
1
What is Included
■
A control module
■
A dual-stage shock sensor (on-board the control module)
■
A soft chirp, six-tone siren
■
A red status LED indicator light
■
A push-button Valet switch
■
A starter interrupt relay
Important Information
Congratulations on the purchase of your state-of-the-art vehicle
security system. This system has been designed to provide years of
trouble-free operation. This system requires no specific maintenance. By carefully reading this owner's guide, you will maximize
the use of this system and its features.
Your Warranty
Your warranty reply card must be returned. If the warranty reply
card is not returned, you do not have a warranty. It is also necessary to keep your receipt, which reflects that the product was
installed by an authorized dealer. Make sure that you receive the
warranty card from your dealer.
2
© 2000 Directed Electronics, Inc.
FCC/ID Notice
This device complies with Part 15 of FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired
operation.
Caution: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate this device.
Using Your System
Arming
You can arm the security system by locking the vehicle doors with
your factory keyless entry transmitter. When the system arms, you
will hear a short siren sound (chirp) and the parking lights will
flash once. Once armed, the status LED will flash once per second
to indicate that your vehicle is being actively protected. If you
hear a second chirp after arming and notice that the status LED is
flashing in a grouped pattern, this signals Bypass Notification,
which is described in the Diagnostics section of this manual.
NOTE: If the ignition is turned on within 60 seconds of arming the security system, the system will automatically disarm.
© 2000 Directed Electronics, Inc.
3
Arming the security system protects your vehicle in the
following ways:
■
Light impacts trigger a Warn Away® Response, causing the
siren to chirp and the parking lights to flash for a few
seconds.
■
Heavy impacts trip a triggered sequence, causing the siren to
sound continuously and the parking lights to flash for either
a 30 or 60-second period. (See Programming Options.)
■
If a door is opened, the siren immediately starts chirping and
the parking lights instantly start flashing. Three seconds
later, the siren output changes to a continuous blast. This
two-stage progressive response allows you time to disarm the
system with your transmitter if a door is inadvertently
opened while the system is armed. This feature can also be
programmed for delayed response, which allows you 15 seconds to disarm the system before the full trigger activates.
(See Programming Options)
■
The starter interrupt relay prevents the vehicle’s starter
from cranking.
Disarming
You can disarm the security system by unlocking the vehicle doors
with your transmitter. When the system disarms, two chirps are
emitted, the parking lights flash twice, and the LED stops
flashing. The siren chirping either four or five times when
disarming indicates Tamper Alert. (See Diagnostics section for
more details.)
4
© 2000 Directed Electronics, Inc.
Disarming Without a Transmitter
If your transmitter is lost or damaged, you can manually disarm
your security system.
To disarm using the Valet switch:
To disarm the security system without a transmitter, you must
have the ignition key and know where the Valet switch is located.
Be sure to check with your installer at the time of installation for
both the location and the preset response (1-5 presses) of the
Valet switch.
Turn the ignition key on and press
the Valet switch the preset number
of times within 15 seconds. If the
system does not disarm, you may
DRW-35
have waited too long to press the
Valet switch; turn the ignition off
and repeat the process.
IMPORTANT! The Valet switch can be programmed to respond to 1-5
presses for the disarm function. You must check with the installer to
verify the programming for your individual unit.
LOCATION OF VALET SWITCH______________________________
To disarm using the vehicle key:
In addition to being able to disarm the security system using the
Valet switch, your system may have been programmed so that it
can be disarmed whenever the vehicle key is used to open the driver’s or passenger’s door.
© 2000 Directed Electronics, Inc.
5
NOTE: This feature is only available if your system has been programmed
with the Level I security setting. (See Glossary section of this manual for
Level I security description.) Consult with your installer to determine if
your vehicle has been programmed for Level I security.
To disarm the security system with the vehicle’s door key:
1.
Insert the key into one of the door key cylinders.
2.
Turn the key until the vehicle door(s) unlocks. The siren
will chirp to confirm that the security system has been
disarmed.
Panic Mode (Optional)
Panic Mode is a programmable option of your security system. (See
Programming Options section of this guide.) This is because most
original equipment from the manufacturer (OEM) keyless entry
systems already have a remote-activated panic feature. In order for
Panic Mode to be operational, the siren or horn must be connected
to the security system.
If you are threatened in or near your vehicle, you can attract
attention by activating Panic Mode. Press the lock button on your
factory keyless entry transmitter twice within three seconds
to sound the siren and flash the parking lights for 30 seconds. To
stop Panic Mode at any time, press the unlock button on your
transmitter.
NOTE: Panic Mode is not available with all factory keyless entry
systems, due to the fact that the lock button may not be triggered a
second time once the vehicle doors have been locked with the factory
transmitter.
6
© 2000 Directed Electronics, Inc.
Trunk Access While the System Is Armed
Trunk access with your transmitter:
While the system is armed, you can open the trunk by pressing the
trunk release button on your transmitter without triggering the
alarm. Only the trunk sensors are bypassed while the rest of the
security system remains armed. Normal trunk monitoring will
resume 5 seconds after the trunk has been closed.
Trunk access with your key:
If the system is programmed for Level I security (see Glossary
section of this manual for a description of Level I security), you
may also open the trunk with your vehicle key while the system is
armed, without triggering the alarm. Normal trunk monitoring will
resume 5 seconds after the trunk has been closed. Consult with
your installer to determine if your vehicle has been programmed for
Level I security.
NOTE: This feature is not available for Buick LeSabres, Oldsmobile
Auroras, Pontiac Bonnevilles and Jeep Grand Cherokees. The alarm will
trigger if you open the trunk of one of these vehicles with the key while
the system is armed.
Valet Mode
Valet Mode is a feature that prevents your security system from
arming or triggering either automatically or with your factory
keyless entry transmitter. In Valet Mode, the security system will
not arm, even with the remote transmitter, but all convenience
functions, such as door locks, trunk release, etc., will function normally. Valet Mode is useful when washing or servicing your vehicle.
© 2000 Directed Electronics, Inc.
7
To enter or exit Valet Mode:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
DRW-35
switch within 10 seconds.
The status LED will light steadily if you are entering Valet Mode and
will turn off if you are exiting Valet Mode.
Remote Valet
You can also activate Valet Mode with your transmitter:
1. Open any vehicle door.
2. Press the lock button on your transmitter.
3. Press the unlock button on your transmitter.
4. Press the lock button on your transmitter again.
The status LED will light solid if you are entering Valet Mode and
will turn off if you are exiting Valet Mode.
NOTE: The Remote Valet feature will not work with all factory keyless
entry systems, as some systems do not work when a vehicle door is open.
Nuisance Prevention® Circuitry
Your system has Nuisance Prevention Circuitry (NPC®). This circuitry
prevents annoying repetitive trigger sequences due to faulty door
pin switches or conditions such as thunder, jackhammers, airport
noise, etc.
8
© 2000 Directed Electronics, Inc.
Here's how NPC works: If the alarm is triggered by the same sensor
or switch three times within a 60 minute period, your system interprets this pattern of triggers as false alarms. After the third trigger,
your system ignores, or bypasses, that sensor or switch (along with
any other sensors or switches sharing the same zone) for 60
minutes. If the bypassed sensor is triggered again while it is
already being bypassed, the 60-minute bypass period will start
over. This ensures that a sensor that is continually being triggered
will remain bypassed.
The vehicle doors are protected differently. If your security system
is triggered by an open door for three, full 30-second cycles (one and
one half minutes), it will bypass the doors until the trigger ceases.
NOTE: Arming and disarming the security system does not reset NPC. The
only ways to reset a bypassed zone are for that zone not to be triggered
for 60 minutes or to turn the ignition key on. When testing your system,
it is important to remember that the False Alarm Prevention Circuitry can
cause zones to be bypassed and appear not to work properly. If five
chirps are heard when disarming the system, NPC was engaged. To clear
the memory, turn the ignition key on.
Diagnostics
The microprocessor at the heart of your system has the ability to
constantly monitor all of the switches and sensors connected to it.
It can detect any faulty switches or sensors and prevent them from
disabling the entire system. It can also record and report any triggers that occur when you are away from your vehicle.
© 2000 Directed Electronics, Inc.
9
Arming Diagnostics
If the system is armed at the same time that an input is active
(door opening, sensor triggering, etc.), you will hear one chirp to
indicate arming and a second chirp to indicate Bypass Notification.
A Bypass Notification chirp means that the system ignores the
input that was active when the system was armed, until that input
ceases. Three seconds after that input ceases, the system resumes
normal monitoring. For example, if your vehicle has an interior
light exit delay and you arm the system before the light turns off,
you may hear a second Bypass Notification chirp. Once the light
turns off, however, the system resumes normal monitoring.
NOTE: Bypass Notification does not occur if the chirps have been programmed by the installer not to sound.
Disarming Diagnostics
Your security system has a Tamper Alert feature that notifies you
of triggers that occur while you are away from your vehicle. If the
siren emits four chirps when you disarm, this indicates that the
system was triggered in your absence. Five chirps when disarming
indicates that a specific zone was triggered so many times that the
Nuisance Prevention Circuitry has bypassed that zone. In both
cases, the pattern of the flashing status LED will indicate which
zone was triggered (see Table of Zones). The LED does not,
however, report when Warn Away Responses have been activated;
only full Triggered Sequences are reported. The system retains this
information in its memory and continues to chirp four or five times
each time it is disarmed, until the next time the ignition is turned on.
10
© 2000 Directed Electronics, Inc.
Table of Zones
A zone is represented by the number of LED flashes used by the
system to identify a particular type of input. Standard input
assignments are listed in the following table, along with spaces to
write in any optional sensors or switches that have been installed.
ZONE
(Number of
LED Flashes)
DESCRIPTION
DEALER-INSTALLED
OPTIONS
1
Instant trigger - often used
for hood/trunk pinswitches
2
Instant trigger - a heavier impact
detected by the on-board shock sensor
3
4
5
Door data bus trigger
Optional sensor
Ignition trigger
NOTE: The Warn Away response will not report on the LED.
Programming Options
Programming options control your system's normal, operational
setup. Most options do not require additional parts, but some may
require installation labor.
The system's programming options are listed here, with the
factory default settings in bold:
■
Active Arming (only with the remote) or Passive Arming (automatic arming occurring 30 seconds after the last door is closed).
© 2000 Directed Electronics, Inc.
11
■
Arming and disarming confirmation siren chirps, on or off.
■
Active Door Locking (only when arming with the transmitter)
or Passive Door Locking (with Passive Arming).
■
Valet Switch Pulse Count: The number of times the vehicle's
Valet switch needs to be pressed to disarm the security
system. One to five pulses can be programmed, with the
default setting being one pulse.
■
Siren Tones and Chirp Volume: The output of the siren consists
of six different tones in sequence. Your dealer can eliminate
any of these tones, resulting in a unique, easily identifiable
siren sound. The chirps can be programmed for either full
volume or six decibels quieter than full alarm blast.
■
Siren Duration: The length of the triggered sequence can be
programmed so that the siren sounds and the parking lights
flash for either 30 seconds or 60 seconds.
■
Instant or Delayed Door Trigger Response: In the standard
configuration the security system will instantly provide a
Progressive Response if the door is opened while the system
is armed. The siren will chirp and the parking lights will flash
for a few seconds followed by a full trigger response. In the
delayed mode, nothing will happen for the first 15 seconds
after the door is opened. After 15 seconds, the unit begins
the full trigger response.
■
Panic Mode or Optional Accessory: This unit is capable of controlling an optional accessory, such as power window control.
In the default setting, pressing the lock button of the factory
transmitter twice will activate Panic Mode. If the unit is
12
© 2000 Directed Electronics, Inc.
custom configured, however, pressing the lock button twice
will activate this optional accessory.
NOTE: The installation of an optional accessory will require additional
parts and labor and will also eliminate the Remote Panic Mode feature.
■
Level I or Level II Security: Level I security allows for access
to the system’s convenience features in the event that the
transmitters are lost, stolen or damaged. Selecting Level II
security will provide a higher level of security if the transmitters are lost, stolen or damaged, but allows access to only
some of the system’s convenience features. (See Glossary
section of this manual for detailed explanations of Level I
security and Level II security.)
Security & Convenience
Expansions
Here we have listed only some of the many expansion options
available. Please consult your dealer for a complete list of the
options available for use with your system.
Domelight Supervision: The domelight will light for 30 seconds
each time the security system is disarmed using the transmitter.
This feature is useful for seeing inside before entering the vehicle.
Valet® Start System: For the ultimate in convenience, the Valet®
Start System can start your vehicle, monitor engine functions, and
power your climate control system with a push of a button!
© 2000 Directed Electronics, Inc.
13
Over-rev protection, open-hood lockout, brake-pedal shutoff, and
automatic timer shutoff are all included. (Only for automatic-transmission, fuel-injected gasoline vehicles.)
Power Window Control: Automatic power window control is provided with the 529T and 530T systems.
Glossary of Terms
Control Module: The "brain" of your system. Usually hidden underneath the dash of the vehicle. It houses the microprocessor
that monitors your vehicle and controls all of the security system
functions.
Input: Any physical connection to the security system. An input
can be provided through a sensor, pinswitch or by existing systems
in the vehicle, such as the ignition or courtesy lights.
LED: A red light mounted inside the vehicle, at a location determined by the installer. The LED indicates the status of your security
system and also reports triggers and faults in the system or sensors.
Level I Security: A convenience setting that allows you to disarm
the security system at the vehicle’s door key cylinder, in the event
that the factory transmitter is lost, stolen or damaged. Level I security also allows you to pop the trunk using the trunk key or the factory transmitter while the rest of the vehicle remains armed.
14
© 2000 Directed Electronics, Inc.
Level II Security: A high security setting that protects your vehicle at the door and trunk key cylinders. With Level II security, the
system cannot be disarmed at the door key cylinder with a vehicle key. Also, the trunk cannot be accessed with the vehicle key
while the system is armed, without triggering the alarm. (The
transmitter can still be used to disarm the system and to access
the trunk while the system is armed.) Level II security will
protect your vehicle in cases when someone with an unauthorized
coded key attempts to enter the vehicle. It also offers protection
if someone attempts to force one of the key cylinders to unlock
the vehicle.
Shock Sensor: A dual-stage shock sensor located on the control
module that detects impacts to the vehicle or glass.
Starter Interrupt Relay: An automatic switch controlled by the
system that prevents the starter from cranking whenever the
system is armed. The vehicle is never prevented from cranking
when the system is disarmed, in Valet Mode, or if the starter interrupt relay fails.
Trigger or Triggered Sequence: The "setting off" or "tripping" of
the alarm. A Triggered Sequence consists of the siren sounding and
the parking lights flashing for 30 or 60 seconds.
Valet Switch: A small, push-button switch mounted inside the
vehicle, at a location determined by the installer. This switch is
used to override the alarm when a transmitter is lost or damaged.
The Valet switch can also be used to put the system into Valet Mode.
© 2000 Directed Electronics, Inc.
15
Warn Away Response: Light impacts to the vehicle generate the
Warn Away Response, which consists of several seconds of siren
chirps and flashing parking lights.
Zone: A zone is a separate input that the alarm can recognize as
unique. Each input to the system is connected to a particular
zone. Two or more inputs may share the same zone.
16
© 2000 Directed Electronics, Inc.
✂
QUICK REFERENCE GUIDE:
To arm using your remote
Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet.
■ To arm the system, lock the vehicle doors with your factory keyless entry
transmitter. When the system arms, you will hear one chirp and the
parking lights will flash once.
To disarm using your remote
■ To disarm the system, unlock the doors using your factory keyless entry
transmitter. When the system disarms, you will hear two chirps and the
parking lights will flash twice.
Disarming without a transmitter
■ To disarm with the Valet switch: Turn on the ignition key. Then press the
Valet switch the pre-programmed number of times within 15 seconds. If
the system does not disarm, you may have waited too long; turn the
ignition off and repeat the process.
■ To disarm using the vehicle key: Insert the key into one of the door key
cylinders. Turn the key until the door(s) unlocks. The siren will chirp to
confirm that the security system has been disarmed. Note: Disarming
with the vehicle key will only work if your system has been programmed
for Level I security.
To activate or deactivate Panic Mode
■ Press the lock button on your factory keyless transmitter twice within
three seconds to enter Panic Mode. The siren will sound (or the horn will
honk) and the parking lights will flash for 30 seconds. To stop Panic
Mode at any time, press the unlock button on your factory keyless entry
transmitter. Note: Your system may not be programmed for Panic Mode
feature.
To enter or exit Valet Mode
■ To enter or exit Valet Mode, turn the ignition key on and then off. Then
press and release the Valet switch within 10 seconds. The status LED will
light steadily if you are entering Valet Mode and will turn off if you are
exiting Valet Mode.
✂
Remote Valet
■ To activate Valet Mode with your factory keyless entry transmitter, first
open any vehicle door. Then press the lock button on your transmitter.
Press the unlock button. Then press the lock button again. The status
LED will light solid if you are entering Valet Mode and will turn off if you
are exiting Valet Mode. Note: The Remote Valet feature may not work
with all factory keyless entry systems, but you should still be able to
enter Valet Mode manually, using the Valet switch.
© 2000 Directed Electronics, Inc.
17
The company behind this system is Directed Electronics, Inc.
Since its inception, the company known as Directed Electronics, Inc. (DEI®) has had
one purpose—to bring the proven advantages of microprocessor and I.C. technology
to the automotive industry.
As a recipient of numerous patents, DEI® has established new standards in electronic
design, automated manufacturing, and dealer support. Its electronic products are
sold and serviced worldwide.
Call (800) 477-1372 for more information about our products and services.
DEI is committed to delivering on time, the best products we know how to provide,
and to constantly work with our customers and vendors to improve our products,
quality, delivery and customer friendly features.
Directed Electronics, Inc.
Vista, CA 92083
© 2000 Directed Electronics, Inc. - All rights reserved
G417A 9/00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising