ATTENTION! Kit Type: PROXIMA

ATTENTION! Kit Type: PROXIMA
Proxima Installation
Configuration and Connections
SYSTEM 8/10 Plus
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: PROXIMA
Included Communications Adapter(s):
Quantity
1
1
1
1
1
Part Number
26-467-01
26-474-01
26-458-01
26-520-01
26-523-01
Description
ADP, UNV, “A”
ADP, UNV, “F”
ADP, NEC MT
ADP, UNV “M”
ADP, UNV “N”
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “✔” IN THE “Config as” COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
Config
as
Model
PROXIMA Pro AV 9310/9320/
9400, DP9250
Rotary Switches Cable
SW15 Settings
Comm
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
✔
Proxima Pro AV
9320/9400
0
0
F
C
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01
✔
Proxima Pro AV 9310
0
0
F
C
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-467-01
✔
Proxima DP9250
0
0
F
C
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-474-01
Proxima DLP DX1
1
0
F
0
J2
↓ ↓ ↑ ↓ ↑ ↓ ↓ ↓ ↑ ↓ 26-458-01
Proxima 6850
0
0
E
C
J2
↓ ↓ ↑ ↓ ↑ ↓ ↑ ↓ ↑ ↓ 26-520-01
Proxima 6150
0
0
E
F
J2
↓ ↓ ↑ ↓ ↑ ↓ ↑ ↓ ↑ ↓ 26-523-01
Extron • System 8/10 PLUS • User’s Manual • P/N 68-481-01 Rev. D
Page 1
Proxima Installation
Configuration and Connections
Proxima Pro AV 9310/9320/9400 Projector Configuration
Verify that the System 8/10 PLUS is already configured for the Proxima 9310/9320/
9400 projector. The general setup is explained on page 3-4 and the switch
settings for the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS
front panel. See bottom of page 3-3. The label on the back of the access cover
also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS
to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config
Model
as
✔
Rotary Switches Cable
RS1 RS2 RS3 RS4 J2/J3
Proxima Pro AV
9310/9320/9400
0
0
F
C
J2
SW15 Settings
1 2
3
4
5
6
Comm
7 8
↓ ↓ ↑ ↓ ↑ ↓
9 10
↓ ↓ ↑ ↓
Adapter
26-467-01
¯
ON
_RS5 is for RGB switching
delay. See page 3-4 for
more information on switch
functions.
1
2
3
4
5
6
7
8
9
10
SW15 DIP Switch
RS2
RS3
RS5 RS2 RS1
RS4
RS1
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next
to “Proxima”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless
this is part of a master/slave system, set #3 and #5 to the up position and the
others down. See illustration to the left.
Use the illustration on the following page to do the next steps.
5. Connect the Comm Adapter’s 9-pin male connector to the 9-pin female “Remote
1” connector on the rear panel of the projector.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the
Comm Adapter to the 15-pin HD “Projector Control” port located on the rear
panel of the System 8/10 PLUS.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the
Proxima projector inputs according to the application requirements.
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 PLUS and projector to normal operation.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-481-01 Rev. D
Page 2
Proxima Installation
Configuration and Connections
Proxima 9310/9320/9400 Projector Connections
Use the illustration below when connecting the System 8/10 PLUS to a Proxima
projector. Refer to Proxima documentation to continue the installation.
VIDEO/Y C/Cb(B-Y) Cr(R-Y)
S-VIDEO
AUDIO 1
R
VIDEO/Y C/Cb(B-Y) Cr(R-Y)
S-VIDEO
AUDIO 1
R
VIDEO/Y C/Cb(B-Y) Cr(R-Y)
S-VIDEO
AUDIO 1
R
USB 2
CONTROL PORT 2
AC JACK SERIAL PORT
L
G
B
H
V
ANALOG RGB
L
ANALOG RGB
AUDIO OUT
R
S-Video
R
L
AUDIO 2
R
ComAdapter
26-467-01 "A"
Composite
Video
CONTROL PORT 1
L
AUDIO 1
R
USB 1
L
L
9-Pin Male
A
9-Pin Male
RGBHV 5 BNC
9-Pin Female
* the projector’s S-video DIN connector may also
be used for S-video input
15-Pin Male
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-481-01 Rev. D
Page 3
Proxima Installation
Configuration and Connections
Proxima DP9250 Projector Configuration
Verify that the System 8/10 PLUS is already configured for the Proxima DP9250
projector. The general setup is explained on page 3-4 and the switch settings for
the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS
front panel. See bottom of page 3-3. The label on the back of the access cover
also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS
to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config
Model
Rotary Switches Cable
as
✔
RS1 RS2 RS3 RS4 J2/J3
Proxima DP9250
0
0
F
C
J2
SW15 Settings
1 2
3
4
5
6
Comm
7 8
↓ ↓ ↑ ↓ ↑ ↓
9 10
↓ ↓ ↑ ↓
¯
ON
_RS5 is for RGB switching
delay. See page 3-4 for
more information on switch
functions.
1
2
3
4
5
6
7
8
9
Adapter
26-467-01
or 26-474-01
10
SW15 DIP Switch
RS2
RS3
RS5 RS2 RS1
RS4
RS1
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next
to “Proxima”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right.
Unless this is part of a master/slave system, set #3 and #5 to the up position and
the others down. See illustration to the left.
Use the illustration on the following page to do the next steps.
5. Connect the Proxima DIN adapter to the projector’s “PC Control 2 “ port. Next,
connect the Comm Adapter’s 9-pin male connector to the 9-pin female end of
the Proxima DIN adapter.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the
Comm Adapter to the 15-pin HD “Projector Control” port located on the rear
panel of the System 8/10 PLUS.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the
Proxima projector’s 15-pin “Computer IN 1” input according to the application
requirements.
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-481-01 Rev. D
Page 4
Proxima Installation
Configuration and Connections
9. Return System 8/10 PLUS and projector to normal operation.
Proxima DP9250 Projector Connections
Use the illustration below when connecting the System 8/10 PLUS to a Proxima
DP9250 projector. Refer to Proxima documentation to continue the installation.
9-Pin Male
○
○
○
○
○
○
○
○
○
○
○
○
○ ○
○ ○
○ ○
○ ○
○
See Special Note below
○
○
9-Pin Male
○
○
○
○
○
○
○
○
○
○
○
9-Pin Female
○
○
ComAdapter
26-474-01 "F"
○
F
○
15-Pin Male
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
9-Pin Female
9-Pin Male
To switcher's Projector Control port
A
To projector's Control Port 2
9-Pin Male
9-Pin Female
Special Note: _____ Certain Proxima projectors may not come equipped with a 9-pin serial port
connector. In those situations, the Com adapter must be connected to Control
Port 2 using the projector’s special DIN to 9-pin serial adapter, as illustrated
below.
Proxima DIN to 9-pin adapter
Extron Com Adapter
26-467-01 "A"
or 26-474-01 "F"
Extron • System 8/10 PLUS • User’s Manual • P/N 68-481-01 Rev. D
Page 5
Proxima Installation
Configuration and Connections
Proxima DLP DX1 Projector Configuration
Verify that the System 8/10 PLUS is already configured for the Proxima DLP DX1
projector. The general setup is explained on page 3-4 and the switch settings for
the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS
front panel. See bottom of page 3-3. The label on the back of the access cover
also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS
to verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config
Model
Rotary Switches Cable
as
RS1 RS2 RS3 RS4 J2/J3
Proxima DLP DX1
1
0
F
0
J2
SW15 Settings
1 2
3
4
5
6
Comm
7 8
↓ ↓ ↑ ↓ ↑ ↓
9 10
↓ ↓ ↑ ↓
Adapter
26-458-01
¯
_RS5 is for RGB switching
delay. See page 3-4 for
more information on switch
functions.
ON
1
2
3
4
5
6
7
8
9
10
SW15 DIP Switch
RS2
RS3
RS5 RS2 RS1
RS4
RS1
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next
to “Proxima DLP DX1”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right.
Unless this is part of a master/slave system, set #3 and #5 to the up position and
the others down. See illustration to the left.
Use the illustration on the following page to do the next steps.
5. For S-video, connect the S-video DIN connector to the “In S-video” port of the
projector. For composite video, connect the composite video cable to the
“Video” port of the Proxima projector.
6. Connect the DIN connector of the Comm adapter to the projector’s “PC Control”
port. Next, connect the CC-50' (or CC-100') cable from the 9-pin male connector
of the Comm Adapter to the 15-pin HD “Projector Control” port located on the
rear panel of the System 8/10 PLUS.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the
Proxima projector’s 15-pin female “RGB” input according to the application
requirements.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-481-01 Rev. D
Page 6
Proxima Installation
Configuration and Connections
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 PLUS and projector to normal operation.
Proxima DLP DX1 Projector Connections
Use the illustration below when connecting the System 8/10 PLUS to a Proxima
DLP DX1 projector. Refer to Proxima documentation to continue the installation.
REMOTE
IN S-VIDEO
VIDEO
L
AUDIO
R
PC CONTROL
IN
OUT
RGB
AUDIO
OUT
RGB
AUD
Comm Adapter
26-458-01
9-Pin Male
9-Pin Female
Composite Video
15-Pin Male
15-Pin Male
RGBHV 5 BNC
S-Video
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-481-01 Rev. D
Page 7
Proxima Installation
Configuration and Connections
Proxima 6850 Projector Configuration
Verify that the System 8/10 PLUS is already configured for the Proxima 6850
projector. The general setup is explained on page 3-4 and the switch settings for
the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS
front panel. See bottom of page 3-3. The label on the back of the access cover
also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS to
verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config
Model
as
Rotary Switches Cable
RS1 RS2 RS3 RS4 J2/J3
Proxima 6850
0
0
E
C
J2
SW15 Settings
1 2
3
4
5
6
Comm
7 8
↓ ↓ ↑ ↓ ↑ ↓
9 10
↑ ↓ ↑ ↓
Adapter
26-520-01
¯
ON
_RS5 is for RGB switching
delay. See page 3-4 for more
information on switch
functions.
1
2
3
4
5
6
7
8
9
10
SW15 DIP Switch
RS2
RS3
RS5 RS2 RS1
RS4
RS1
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next
to “Proxima 6850”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless
this is part of a master/slave system, set #3 and #5 to the up position and the
others down. See illustration to the left.
Use the illustration on the facing page to do the following steps.
5. Connect the Comm Adapter’s 15-pin female connector to the 15-pin male
“Control” connector on the rear panel of the projector.
6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the Comm
Adapter to the 15-pin HD “Projector Control” port located on the rear panel of the
System 8/10 PLUS.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the
Proxima 6850 projector input according to the application requirements.
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
9. Return System 8/10 PLUS and projector to normal operation
Extron • System 8/10 PLUS • User’s Manual • P/N 68-481-01 Rev. D
Page 8
Proxima Installation
Configuration and Connections
Proxima 6850 Projector Connections
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○ ○
○ ○
○
○ ○
○ ○
○
○
○ ○
○ ○
○
○
○ ○
○ ○
○
○ ○
○ ○
○
○
○ ○
○ ○
Use the illustration below when connecting the System 8/10 PLUS to a
Proxima 6850 projector. Refer to Proxima 6850 documentation to continue the
installation.
Comm Adapter
26-520-01 "M"
15-Pin Female
M
9-Pin Male
9-Pin Female
RGBHV
15-Pin Male
Composite
Video
S-Video
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-481-01 Rev. D
Page 9
Proxima Installation
Configuration and Connections
Proxima 6150 Projector Configuration
Verify that the System 8/10 PLUS is already configured for the Proxima 6150
projector. The general setup is explained on page 3-4 and the switch settings for
the projector are repeated below.
1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS
front panel. See bottom of page 3-3. The label on the back of the access cover
also has the configuration information.
__________ Before changing anything, remove the AC power cord to the System 8/10 PLUS to
verify that the main power is OFF; also turn the projector power OFF.
2. Set the switches as follows:
Config
Model
as
Rotary Switches Cable
RS1 RS2 RS3 RS4 J2/J3
Proxima 6150
0
0
E
F
J2
SW15 Settings
1 2
3
4
5
6
Comm
7 8
↓ ↓ ↑ ↓ ↑ ↓
9 10
↑ ↓ ↑ ↓
Adapter
26-523-01
¯
ON
_RS5 is for RGB
switching delay. See
page 3-4 for more
information on switch
functions.
1
2
3
4
5
6
7
8
9
10
SW15 DIP Switch
RS2
RS3
RS5 RS2 RS1
RS4
RS1
RS3 RS4
Configured For:
RS-232
3. Use a grease pencil (or other rub-off marker) to mark the space on the label next
to “Proxima 6150”.
4. Locate the switcher’s Address DIP switches on the rear panel, lower right. Unless
this is part of a master/slave system, set #3 and #5 to the up position and the
others down. See illustration to the left.
Use the illustration on the facing page to do the following steps.
5. Connect the Comm adapter’s DIN connector to the projector’s “Mouse 1” port.
6. Connect the CC-50' (or CC-100') communications extension cable from the 9-pin
male connector of the Comm Adapter to the 15-pin HD “Projector Control” port
located on the rear panel of the System 8/10 PLUS.
______ Secure the screws on all D connectors.
7. Connect the BNC (RGBS) cables from the System 8/10 PLUS outputs to the
projector’s 15-pin female “Analog Computer VGA” connector. For composite
video, connect the RCA connector from the System 8/10 Plus to the projector’s
“Video” connector. For S-Video, connect the DIN connector from the System
8/10 Plus to the projector’s “S-Video” connector.
8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The
Main Power LED should light. Apply power to the projector.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-481-01 Rev. D
Page 10
Proxima Installation
Configuration and Connections
9. Return System 8/10 PLUS and projector to normal operation
Proxima 6150 Projector Connections
○
○
Use the illustration below when connecting the System 8/10 PLUS to a
Proxima 6150 projector. Refer to Proxima 6150 documentation to continue the
installation.
REMOTE MOUSE 2 MOUSE 1
CONTROL
ANALOG COMPUTER
VGA (2)
ANALOG COMPUTER
VGA (3)
MONITOR
○
○
○
DIGITAL COMPUTER
DVI (1)
AUDIO
IN
○
AUDIO AUDIO
(1) (2)
OUT
IN (3)
○
○
○
○
○
○
○
○
○
○
VIDEO
○
S-VIDEO
○
○
○
○
○
8-pin male DIN
Comm Adapter
26-523-01 "N"
N
9-Pin Male
9-Pin Female
○
RGBHV
○
○
○
○
○
○
○
○
○
○
○
○
15-Pin Male
○
○
○
○
○
○
○
Composite
Video
○
○
○
○
○
○
○
○
S-Video
_ If the installation includes looping (master/slave) switchers, see Chapter 5.
If Video Loop Back is part of the installation, see pages 2-10 and 2-11.
Extron • System 8/10 PLUS • User’s Manual • P/N 68-481-01 Rev. D
Page 11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement