advertisement
LC-5621
56" - quad full HD LCD display
User manual
K5960013-00
Intentionally left blank
2 ________________________________________________________ Barco - LC-5621 - User manual
1
1.1
1.2
About the manual
About the manual
Contents of the user manual
This manual consists of the following chapters:
Chapter 1: About the manual
Chapter 2: Important notice
Chapter 3: Safety precautions
Chapter 4: Package and storage
Chapter 5: About the product
Chapter 6: Installation
This chapter describes how the monitor should be installed and connected into the system. It incorporates the pin layout of all the connectors.
Chapter 7: Operation
This chapter describes the function and the general operation of all function keys and indicators. How to power up the unit, how to adjust brightness and other adjustments.
Chapter 8: Troubleshooting
This chapter lists some troubleshooting tips for common problems.
Chapter 9: Technical specifications
This chapter tabulates the technical specifications and the dimensions of the display module.
Chapter 10: List of abbreviations
Change record
Revision Date
00 Mar-08
Description
Initial Release
Barco - LC-5621 - User manual ________________________________________________________ 3
About the manual
1.3
Notation convention
Following notations are applicable to this manual and should be respected through the manual.
WARNING :
Warnings – presented in this manual, provide information, which if not adhered to, may result in personal injury or death.
CAUTION :
Cautions – presented in this manual, provide information, which if not adhered to, may result in damage to the equipment.
NOTE :
Notes – presented in this manual, provide information, which emphasize points, significant to understand and operate the unit.
IMPORTANT :
Important – presented in this manual, provide information, which is important to highlight.
4 ________________________________________________________ Barco - LC-5621 - User manual
2
2.1
2.2
2.3
2.4
Important notice
Important notice
Commercial In Confidence
The information contained herein is Barco confidential information. No part of the information contained herein may be disclosed outside of the organization of the recipient, its sub-contractors, and customers in any form or by any means and/or stored in a database or retrieval system without the prior written consent of Barco.
Notice
The technical specifications mentioned in this manual shall under no circumstances be used as proof or item of evidence.
Only the technical specifications defined in the Barco technical specifications document (which is not part of this manual) can be used as a base for contract negotiations.
Note that the DVI-D connectors are not always used according to the standard
DVI-D regulations, carefully follow the instructions of this user manual in order to make the proper connections.
Federal Communication Commission (FCC) notice
This equipment has been tested and found to comply with the limits of an FCC class (refer to the technical specifications of the specific unit for more details about the corresponding class). These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Disposal information
WARNING :
The fluorescent tubes inside the backlight of the LCD contain a small amount of mercury that is considered hazardous to a person's health. Please follow local regulation or laws for disposal.
The LCD panel is composed of multiple layers of glass and protective glass with a small amount of liquid in between. Rough handling or dropping can cause the LCD panel to break. If any part of the skin or body comes in direct contact with the liquid, immediately wash the affected areas with plenty of water for at least 15 minutes. If any symptoms are present after washing, get medical care.
Barco - LC-5621 - User manual ________________________________________________________ 5
Important notice
2.5
Copyright
No parts of this book may be reproduced in any form, by print, photo printing, microfilm or any other means without written permission from Barco NV.
This manual could include inaccuracies or typographical errors. Manual change supplements are revised as often as necessary to keep manuals as current and accurate as possible.
Copyright © Barco NV
6 ________________________________________________________ Barco - LC-5621 - User manual
3
3.1
3.2
Safety precautions
Safety precautions
Safety warning
WARNING :
Electric shock or fire hazard can be caused if critical components are replaced by nonconforming components. These components are marked in this guide by a sign. Replace with conform types only!
Product safety notice
WARNING :
Many electrical and mechanical parts in display units have special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this data and its supplements and bulletins. Electrical components having such features are identified by or * on the schematics and on the parts lists in this data and its supplements and bulletins. The use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part shown in the parts lists in this data and its supplements and bulletins, may create shock or fire.
Barco - LC-5621 - User manual ________________________________________________________ 7
Package & storage
4
4.1
4.2
4.3
Package & storage
General
A safe transport of the units can only be guaranteed if the original undamaged package is used for shipping. Handle with care when transporting.
Keep your original packaging. It is designed for this unit and is the ideal protection during transportation.
Procedure in case of damaging
All shipments should be opened and inspected for concealed damage or pilferage as soon as possible after the arrival at destination. The shipping cartons should be retained for the surveyor’s inspection and full and accurate reserves must be made by a letter or a fax message.
Depending upon the used means of transport, the written protest is subject to different time-rules:
• by sea: the protest has to be issued against the captain and/or ship within 3 days of the delivery of the goods.
• by road: the protest has to be issued against the last road-carrier within 7 days after delivery of the goods.
• by air: the protest has to be issued against the air-carrier within 14 days after delivery of the goods.
In all cases, a claim or potential claim should be reported as soon as possible whether or not full documentation is immediately available.
After completion of all required steps, the claim should normally be finalized within one month. For more information about the claims handling procedure, contact Barco NV.
Storage
Specific storage conditions can be found in the technical specifications. It is best to store the unit in its original packaging, on a shelf in a ventilated and humidity controlled room.
NOTE :
At least every 2 years, all boards containing electrolytic capacitors need to be powered during
24 hours minimum.
8 ________________________________________________________ Barco - LC-5621 - User manual
5
5.1
5.1.1
5.1.2
About the product
About the product
Product description
LC-5621
Barco’s LC-5621 display has been specifically designed for us in dedicated professional applications. The display features quad full High Definition
(3840x2160) and delivers crisp, clear and color-accurate perfect images on a large display size with 56” diagonal.
With the 56” Quad-HD display, operators benefit from a large display surface without having to compromise on image quality or accuracy.
The LCD technology used in the Barco LC series offers many benefits not found in other flat panel technologies:
• High brightness
• High contrast, even in high ambient light environments
• Lower power consumption
• Long lifetime
Main features
Ultra-high resolution
Barco’s LC-5621 is able to show large amounts of data in ultimate detail.
Faster response time
Thanks to its extremely fast response time (6.5 ms gray to gray), the LC-5621 reproduces fast-moving action scenes with vivid accuracy.
Wide viewing angle
The wide viewing angle (176°) and large surface are very beneficial in collaborative environments where detailed information is viewed by multiple participants.
Adjustable color temperature
The color temperature can be set to 5600K, 6500K, 7500K, 8500K, or 9300K to adjust the color balance to different user requirements. User adjustment of the color balance is also possible with R, G and B sliders.
VESA mounting structure for easy installation
Integrated mounting interfaces according to the VESA standards allow easy wall or ceiling installation with VESA-approved standard (VESA MIS F, 800, 400, 8).
Table stands and mounting devices are optional.
Control & diagnostics
With extensive control and diagnostic functions through RS232, the LC-5621 can be easily controlled, both on or off site or in real-time with a simple touch of a button.
Barco - LC-5621 - User manual ________________________________________________________ 9
About the product
5.2
5.2.1
Recommended use
General precautions for all units
For optimum performance, please note the following when setting up and using the unit(s).
• Allow adequate ventilation in case the configuration is built in a rack or a console, so that the heat can properly dissipate.
• Make sure all units are disconnected from mains before connecting the signals.
• The power cable or connector (in case of a split design = *connection cable) is the primary means of detaching the system from the power supply. One of the cable ends should be easily accessible.
• Clean the screen surface of the display with a sponge or soft cleaning cloth.
Do NOT use abrasive cleaning agents, glass cleaner or tissue paper. Use non-aggressive glass cleaning products instead. Do NOT use alcohol/solvents at higher concentration > 5%.
• Avoid displaying fixed patterns on the display for long periods of time to avoid image persistence (after-image effects).
NOTE :
Always power-down the unit before disconnecting the power cable.
5.2.2
IMPORTANT :
Immediately unplug if:
• Power supply cord or plug is damaged.
• If the units have been dropped or the cabinets are damaged.
• If the units don’t operate normally by following operating instructions.
*Connection cable= cable between the panel or display module and control module
Image retention
The specified usage of the monitor with fixed patterns per 24 hours is maximum
2 shifts of 8 hours, with minimum 1 hour of relaxation between the shifts. The
24 months product warranty does not apply to the case of image retention phenomena (after-image, shadows, dark lines and other image artifacts), that may result from a usage outside of this specification.
10 _______________________________________________________ Barco - LC-5621 - User manual
6
6.1
6.1.1
Installation
Installation
Mounting procedure
LC-5621 mounted on stands
The unit is standard mounted on two stands on the rear of the unit. The stands use the VESA mounting holes foreseen in the unit.
The stands can be mounted on two ways as shown in the drawing below.
1
DVI-D (Master) RS232 DVI-D (Slave)
USB HUB
ON
OFF
P C IN
1
DVI-D (Master) RS232 DVI-D (Slave)
USB HUB
ON
OFF
MAIN
POWER AC IN
1 1
1 Stand (2x)
Figure 1: Location of the stands of the LC-5621
Barco - LC-5621 - User manual _______________________________________________________ 11
Installation
6.1.2
LC-5621 with VESA compliant mounting solution
The LC-5621 can be mounted on an arm compliant to the VESA MIS F, 800, 400,
8 standards.
The LC-5621 can also be mounted on a wall or ceiling according to the VESA MIS
F, 800, 400, 8 standards.
1 1
1 1
1
1
DVI-D (Master) RS232 DVI-D (Slave)
USB HUB
ON
OFF
MAIN
POWER AC IN
1
1 VESA mounting holes (8x)
Figure 2: Location of the VESA mounting holes
1
12 _______________________________________________________ Barco - LC-5621 - User manual
6.2
6.2.1
Connecting the signals
Connector location
1 2 3 4
5 6
1
2
3
4
5
6
DVI-D connector (Master)
RS-232 connector
DVI-D connector (Slave)
USB Hub
Power switch
Power connector (AC IN)
Figure 3: Connector location LC-5621
Installation
Barco - LC-5621 - User manual _______________________________________________________ 13
Installation
6.2.2
6.2.2.1
Detailed connector information
Power connector
IEC connector layout
POWER 100 - 240 VAC
Figure 4: Power connector
Power ranging
Automatic selection between the following voltage ranges:
• 90Vac – 140Vac (100V and 115V nominal)
• 180Vac – 264Vac (230V nominal)
• Frequency: 45 – 65Hz
Mains Fuse inside the unit (T 6.3 A H), for fuse replacement procedures, refer to the maintenance manual of the unit.
NOTE :
When connecting mains, check if the power source corresponds with the mains voltage marked on the identification label on the display!
14 _______________________________________________________ Barco - LC-5621 - User manual
6.2.2.2
DVI connector
DVI-D connector layout
DVI-D receptable connector (24 pins), right angle with pegs
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
DVI input pinning
12
13
14
15
8
9
10
11
6
7
4
5
2
3
Pin
1
20
21
22
23
24
16
17
18
19 signal
TMDS Data 2-
TMDS Data 2+
TMDS Data 2/4 Shield
TMDS Data 4-
TMDS Data 4+
DDC Clock
DDC Data
NC
TMDS Data 1-
TMDS Data 1+
TMDS Data 1/3 Shield
TMDS Data 3-
TMDS Data 3+
+5V Power
Ground for +5V
Hot Plug Detect
TMDS Data 0-
TMDS Data 0+
TMDS Data 0/5 Shield
TMDS Data 5-
TMDS Data 5+
TMDS Clock Shield
TMDS Clock+
TMDS Clock-
Installation
Barco - LC-5621 - User manual _______________________________________________________ 15
Installation
6.2.2.3
Control connector
9 pins subD male connector layout
1
6 9
5
Control pinning
6
7
4
5
8
9
2
3
Pin
1 signal
Nc
Signal receive
Signal transmit
Nc
GND
Nc
Nc
Nc
Nc
16 _______________________________________________________ Barco - LC-5621 - User manual
6.3
6.3.1
6.3.1.1
6.3.1.2
Installation
First installation
Case 1: Customer buys NVIDIA Quadro FX 4600
System requirements
Minimum system requirements for using a NVIDIA Quadro FX 4600:
• PC compatible with Intel Pentium® or AMD Opteron® class processor or higher
• Open PCI Express x16 lane slot with open adjacent slot
• Microsoft Windows XP
• 1 GB system memory
• 100 MB of available disk space for full installation
• CD-ROM or DVD-ROM drive
• VGA or DVI-I compatible display
• 750 W power supply (higher capacity may be required for NVIDIA SLI)
NVIDIA Quadro FX 4600
2
1
1
2
Master DVI slot
Slave DVI slot
Figure 5: NVIDIA Quadro FX 4600
Barco - LC-5621 - User manual _______________________________________________________ 17
Installation
6.3.1.3
Downloading the correct drivers
NOTE :
Before you install the LC-5621, use an additional LCD monitor to install the drivers to the workstation.
First the correct driver should be installed on your system.
Go to http://www.nvidia.com
Go to download drivers and select the following items
Now the following screen should appear:
18 _______________________________________________________ Barco - LC-5621 - User manual
6.3.1.4
Installation
Check the checkbox and push the “Download Now” button.
Now the driver should be downloaded on your system.
Installing the drivers
Install the driver of the NVIDIA Quadro FX 4600 by double clicking the icon on your desktop. Following image appears on the screen:
Accept the license agreement and click “Next”.
Barco - LC-5621 - User manual _______________________________________________________ 19
Installation
Click “Next”.
Following screen appears on the screen, click “Next” to install the drivers to your computer.
20 _______________________________________________________ Barco - LC-5621 - User manual
Select “Yes, I want to restart my computer now”. Click “Finish”.
Installation
It is possible that the computer doesn’t restart automatically. If needed, restart the computer manually.
Barco - LC-5621 - User manual _______________________________________________________ 21
Installation
6.3.1.5
Connecting the LC-5621 to the workstation
NOTE :
Switch the additional LCD screen with the LC-5621.
Put DVI-D Master of the unit to the master DVI connector on the graphics card closest to the motherboard. Put DVI-D Slave of the unit to the slave DVI connector on the graphics card furthest from the motherboard.
When the computer is restarted, the following screen appears on the right side of the unit. The left side of the unit is black.
Click “Next” to continue.
Following screen appears on the screen.
22 _______________________________________________________ Barco - LC-5621 - User manual
Installation
Select “Custom setup” and click “Next”.
Following screen appears on the screen.
Select “Color LCD (1 of 2) and click “Next”.
Barco - LC-5621 - User manual _______________________________________________________ 23
Installation
Following screen appears on the screen.
Select the screen resolution and Color quality as shown on the image above.
Click “Next”.
Following screen appears on the screen.
24 _______________________________________________________ Barco - LC-5621 - User manual
Installation
Click “Next”.
Following screen appears on the screen.
Choose “Span” and click “Next”.
Barco - LC-5621 - User manual _______________________________________________________ 25
Installation
Following screen appears on the screen.
Click “Finish”.
Now the left side of the unit and the right side of the unit show the total picture.
26 _______________________________________________________ Barco - LC-5621 - User manual
6.3.2
Installation
Case 2: Workstation delivered by Barco
When the workstation (PWS-101) is provided by Barco, the NVIDIA Quadro FX
4600 will be installed on this work station. The correct drivers of this graphics card will be installed.
The unit can be attached directly to the workstation. Connect the unit with the master DVI-D connector to the master DVI connector of the graphics card. This is the DVI connector closest to the motherboard (as shown on the picture below).
Connect the slave DVI-D connector of the unit to the slave DVI connector of the graphics card. This is the DVI connector furthest of the motherboard (as shown on the picture below).
2
1
1
2
Master DVI slot
Slave DVI slot
Figure 6: Location of the master & slave DVI-connector
Barco - LC-5621 - User manual _______________________________________________________ 27
Operation
7
7.1
7.1.1
7.1.1.1
Operation
Function of primary controls and indicators
Primary controls
Location of the primary controls
1
2
5
6
7
3
4
SOURCE
MODE
ENTER
/+
/-
MENU
7.1.1.2
5
6
7
1
2
3
4
Standby
Source
Mode
Enter
Up
Down
Menu
Figure 7: Primary controls of the LC-5621
Standby button
Pressing this button puts the display in standby mode.
Standby mode means that the power to the LCD panel and backlight is disabled and that all power consumption is reduced to a strict minimum. The display turns black.
To bring the unit out of this mode, press the button again. Power is restored immediately.
28 _______________________________________________________ Barco - LC-5621 - User manual
Operation
7.1.1.3
Source button
SOURCE
7.1.1.4
Pressing this button adjusts the gamma settings of the display.
Mode button
MODE
7.1.1.5
Pressing this button shows information on the display.
Enter button
ENTER
7.1.1.6
Pressing this button enables the user to select/activate the menu item when the
OSD menu is activated.
Up/Down buttons
/+ /-
7.1.1.7
Pressing this buttons will navigate the “cursor” through the OSD menu when active or increase/decrease the selected value in the OSD.
Menu button
MENU
Pressing this button will activate the OSD menu. Pressing this button when the
OSD menu is already activated will close the OSD menu.
Barco - LC-5621 - User manual _______________________________________________________ 29
Operation
7.1.2
7.1.2.1
IR control
Location of the primary controls on the IR control
2
7.1.2.2
7.1.2.3
7.1.2.4
7.1.2.5
3
6
1
F1
F2
F3
F4
F5
ADJ EXIT
PAUSE
?
9
7
0
5
3
1
4
2
8
6
TREBLE
BASS
ENTER
TEXT
PHASE
SHARPN
TINT
COLOR
BRIGHTN
COLOR
BALANCE
VOL
5
6
7
1
2
3
4
4
5
7
F1 (Source)
F2 (Mode)
ADJ (Menu)
EXIT (Menu)
ENTER (Enter)
Stand-by
Up/Down
Figure 8: Location of the primary controls on the IR control
F1 button (IR control)
F1
Pressing this button adjusts the gamma settings of the display.
F2 button (IR control)
F2
Pressing this button shows information on the display.
ADJ button (IR control)
ADJ
Pressing this button will activate the OSD menu.
Exit button (IR control)
EXIT
Pressing this button when the OSD menu is activated will close the OSD menu.
30 _______________________________________________________ Barco - LC-5621 - User manual
7.1.2.6
7.1.2.7
Operation
Enter button (IR control)
ENTER
Pressing this button enables the user to select/activate the menu item when the
OSD menu is activated.
Standby button (IR control)
7.1.2.8
Pressing this button puts the display in standby mode.
Standby mode means that the power to the LCD panel and backlight is disabled and that all power consumption is reduced to a strict minimum. The display turns black.
To bring the unit out of this mode, press the button again. Power is restored immediately.
Up/down buttons (IR control)
7.1.3
7.1.3.1
Pressing this buttons will navigate the “cursor” through the OSD menu when active or increase/decrease the selected value in the OSD.
Indicators
Location of the indicators
1 2
1
2
IR receiver
Power LED
Figure 9: Location of the indicators
Barco - LC-5621 - User manual _______________________________________________________ 31
Operation
7.1.3.2
Power LED
Led indicator
Orange
Green
Mode
Standby
In operation
32 _______________________________________________________ Barco - LC-5621 - User manual
7.2
7.2.1
Adjusting display settings
Overview of the on screen display
Operation
Figure 10: Overview of the on screen display
Barco - LC-5621 - User manual _______________________________________________________ 33
Operation
7.2.2
7.2.2.1
Using the on screen display
Overview of the key functions
Before depicting the OSD menus we will give an overview of the key functions.
Entering one of these menus via control panel?
• Press MENU , the OSD main menu appears on the screen.
• Press /+ or / until the desired submenu is selected.
• Press ENTER to enter the desired submenu.
Quitting a menu?
• To quit a menu push
MENU
.
• Remark: MENU from the main menu closes the OSD.
Changing a value?
• Press /+ or / to select the desired line.
• If the line displays a value that can be modified:
3 Press ENTER and change the value with
Executing a command?
• Go to the desired execute line.
/+ or / keys.
• Press ENTER to execute the command.
Read-only text
• When a line is not selectable, this line is “read-only”.
Entering one of these menus via IR control?
The procedure for entering the menus via IR control is equal to the procedure for entering the menus via control panel.
The buttons used for the IR control are shown below, the left side shows the buttons of the control panel on the display, the right side shows the buttons of the IR control.
34 _______________________________________________________ Barco - LC-5621 - User manual
Operation
7.2.2.2
Main menu
ENTER
MENU
/+
/-
MENU
ENTER
ADJ
EXIT
7.2.2.3
Figure 11: Main menu
The main menu enables the user to scroll through the different menu items of the display.
Brightness menu
Figure 12: Brightness menu
To enter the brightness menu, push
ENTER
. The brightness bar becomes visible.
Push /+ or / to increase/decrease the brightness value.
Barco - LC-5621 - User manual _______________________________________________________ 35
Operation
7.2.2.4
Brightness can be adjusted from 0 (minimum light output) to 100 (maximum light output). The default value for brightness is 30.
Contrast menu
Figure 13: Contrast menu
7.2.2.5
To enter the contrast menu, push ENTER . The contrast bar becomes visible.
Push /+ or / to increase/decrease the contrast value.
Contrast can be adjusted from 0 to 100. The default value for contrast is 50.
Gamma menu
Figure 14: Gamma menu
In the gamma menu, the different gamma settings can be adjusted. One can choose between following gamma settings:
• Gamma off
• Gamma 2.2
• Gamma 2.4
• Gamma 2.6
• Gamma DICOM
• Gamma USER
Gamma DICOM sets the gamma for Medical applications.
Gamma USER activates the LUT that is uploaded via RS-232.
36 _______________________________________________________ Barco - LC-5621 - User manual
Operation
7.2.2.6
Color temp menu
7.2.2.7
Figure 15: Color temp menu
In the color temp menu, the different color temperatures can be set. One can choose between following color temperatures:
• 5600K
• 6500K
• 7500K
• 8500K
• 9300K
User color menu
Figure 16: User color menu
To enter the user color menu, push
ENTER
. The color bar becomes visible. One can adjust the gain of the red, green and blue components. Push increase/decrease the color value.
Color can be adjusted from 0 to 255.
/+ or / to
Barco - LC-5621 - User manual _______________________________________________________ 37
Operation
7.2.2.8
Sys info
7.2.2.9
Figure 17: System info
This menu shows system information such as horizontal frequency (HF), vertical frequency (VF), resolution (Res), model number (Mdl), firmware version (MVer),
FPGA version (FVer) and runtime hours (Hrs).
Fan status menu
Figure 18: Fan status menu
The fan status menu shows the fan speed (RPM) of the different fans and the temperature reading of the thermal sensor in the display.
38 _______________________________________________________ Barco - LC-5621 - User manual
Operation
7.2.2.10
Language menu
Figure 19: Language menu
The language of the OSD menus can be set in this menu. The different languages that one can choose are:
• English
• German
• Spanish
• Italian
• Japanese
7.2.2.11
Misc menu
Figure 20: Misc menu
One can reset all settings of the display to the factory settings by entering this menu.
The display RS-232 address can be adjusted via “Display Addr”.
Barco - LC-5621 - User manual _______________________________________________________ 39
Troubleshooting
8
8.1
Troubleshooting
Troubleshooting procedure
No picture on screen.
• The signal cable should be completely connected to the graphics card/computer.
• The graphics card should be completely seated in its slot.
• Check the power switch should be in the ON position.
• Front power switch and computer power switch should be in the ON position.
• Check to make sure that a supported mode has been selected on the graphics card or system being used (Please consult graphics card or system manual to change graphics mode.).
• Check the monitor and your graphics card with respect to compatibility and recommended settings.
• Check the signal cable connector for bent or pushed-in pins.
• Ensure the DVI input mode is set to digital when the MAC digital output is connected to the DVI-I connector.
Image persistence.
• Image persistence is when a residual or “ghost” image of a previous image remains visible on the screen. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. See chapter “Recommended use”.
Image is unstable, unfocused or swimming in apparent.
• Signal cable should be completely attached to the computer.
No signal
• Signal cable should be completely attached to the computer.
• Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).
• If no video is present on the screen, turn the power button off and on again.
LED on monitor is not lit (no green or orange color can be seen)
• Power switch should be in the ON position and power cord should be connected.
• Check the power cable should be connected surely.
40 _______________________________________________________ Barco - LC-5621 - User manual
9
9.1
9.1.1
9.1.2
9.1.2.1
9.1.2.2
9.1.2.3
9.1.2.4
9.1.2.5
Technical specifications
Technical specifications
Electro-optical specifications
Panel
• a-Si TFT Active Matrix LCD (AM-LCD) – 8 bit/color
• Super MVA technology, normally black
Image specifications
Screen dimensions
• Aspect ratio 16:9
• Screen dimensions:
3 1244.16 x 699.84 mm (48.98” x 27.55”)
3 1427.48 mm (56.2”) diagonal
Screen specifications
• 16.8 million colors - 256 gray scales
• Typical viewing angle:
3 Horizontal: 176°, Vertical: 176° @ CR>=30
Light output
• White surface luminance at maximum brightness
3 max. 400 cd/m² (116.75 fL)
Contrast ratio
• Contrast ratio in dark environment: 1200:1
• Typical specular reflection: <0.5%
• Typical diffuse reflection: TBD%
Resolution
• 3840 x 2160 pixels.
• 1 pixel is composed of 3 sub pixels R, G and B (RGB Vertical Stripe configuration)
• pixel dimensions: 0.108 mm x 0.342 mm
Barco - LC-5621 - User manual _______________________________________________________ 41
Technical specifications
9.1.2.6
9.1.2.7
Color temperature
• color temperatures can be switched between 5600K, 6500K, 7500K, 8500K,
9300K or USER
• Typical CIE coordinates are mentioned in the table below
RED
GREEN
BLUE
WHITE x
0,651 + 0.03
0,269 + 0.03
0,144 + 0.03
0,285 + 0.03
y
0,332 + 0.03
0,593 + 0.03
0,060 + 0.03
0,293 + 0.03
CIE-1931 x,y coordinates are measured
Response time (at 25°C ambient)
• Rise time (black to white transition): typ. 8 ms
• Fall time (white to black transition): typ. 8 ms
42 _______________________________________________________ Barco - LC-5621 - User manual
9.1.3
9.1.3.1
Signal inputs
DVI connector
DVI-D connector layout
DVI-D receptable connector (24 pins), right angle with pegs
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
Technical specifications
DVI input pinning
Pin
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
21
22
23
24
17
18
19
20 signal
TMDS Data 2-
TMDS Data 2+
TMDS Data 2/4 Shield
TMDS Data 4-
TMDS Data 4+
DDC Clock
DDC Data
NC
TMDS Data 1-
TMDS Data 1+
TMDS Data 1/3 Shield
TMDS Data 3-
TMDS Data 3+
+5V Power
Ground for +5V
Hot Plug Detect
TMDS Data 0-
TMDS Data 0+
TMDS Data 0/5 Shield
TMDS Data 5-
TMDS Data 5+
TMDS Clock Shield
TMDS Clock+
TMDS Clock-
Barco - LC-5621 - User manual _______________________________________________________ 43
Technical specifications
9.1.3.2
Control connector
9 pins subD male connector layout
1
6 9
5
9.1.4
9.1.4.1
9.1.4.2
9.1.4.3
9.1.4.4
Control pinning
6
7
4
5
8
9
2
3
Pin
1 signal
Nc
Signal receive
Signal transmit
Nc
GND
Nc
Nc
Nc
Nc
Power supply specification
115 Vac / 220 Vac (50 ~ 60 Hz) supply
• Nominal voltage: 115 Vac or 220 Vac
• Operates between 85 Vac – 264 Vac
• Frequency range: 50 ~60 Hz
Power consumption
• Pmax = 500 W
Safety
• Unit meets:
3 IEC 60950-1
3 IEC 60601-1
Power connector
• 115/220 Vac
3 IEC power chassis connector for 115 Vac and 220 Vac
44 _______________________________________________________ Barco - LC-5621 - User manual
9.1.5
9.1.5.1
9.1.5.2
9.1.5.3
Technical specifications
Human Machine Interface (HMI)
On-Screen Display (OSD)
• The On-Screen Display (OSD) feature is the ability to display text on top of the input.
• The OSD can be used to adjust parameters like brightness, contrast, gamma,…
• The OSD menu can be accessed via the IR control.
• This information is also accessible form the host processor through the RS-
232 interface according to the BARCO remote protocol.
Controls
The controls of the monitor are located on the right side of the unit (seen from front). There are 7 buttons:
Main function
Power (¨)
Menu
Standby / switch into operation
Mode
Enter c/+ d/-
Menu
Indicators
Led indicator
Orange
Green
Show information
Activate selection
Scroll up for menu items
Scroll down for menu items
Opens OSD, exits OSD, exit OSD control
Mode
Standby
In operation
Barco - LC-5621 - User manual _______________________________________________________ 45
Technical specifications
9.2
9.2.1
9.2.2
9.2.3
9.2.3.1
9.2.3.2
Mechanical specifications
Dimensions
Height
Width
Depth
With stand
866 mm (34.09”)
1345.1 mm (52.96”)
300 mm (11.81”)
Without stand
800.8 mm (31.53”)
1345.1 mm (52.96”)
135.2 mm (5.32”)
Weight
• With stand: 58 kg (128 lbs)
• Without stand: 53 kg (117 lbs)
Mounting specifications
VESA compliant mounting solution
The LC-5621 is standard mounted on a stand.
The unit is foreseen with mounting holes to be mounted on a vesa arm or wall with VESA MIS F, 800, 400, 8 standards.
Drawings LC-5621
Figure 21: LC-5621 Front view
46 _______________________________________________________ Barco - LC-5621 - User manual
DVI-D (Master) RS232 DVI-D (Slave)
USB HUB
ON
OFF
MA IN
POWE R AC IN
Figure 22: LC-5621 Rear view
Figure 23: LC-5621 Bottom view
Technical specifications
Barco - LC-5621 - User manual _______________________________________________________ 47
Technical specifications
Figure 24: LC-5621 Side view
48 _______________________________________________________ Barco - LC-5621 - User manual
9.3
9.3.1
9.3.1.1
9.3.1.2
9.3.2
9.3.3
9.3.4
9.3.4.1
9.3.4.2
9.4
9.4.1
9.4.2
Technical specifications
Environmental specifications
Temperature
Operating (continuous)
• High temp.: + 35°C (+95°F)
• Low temp.: + 5° C (+41°F)
Storage
• High temp.: +55°C (+131°F)
• Low temp.: -20°C (-4°F)
Altitude/Low pressure
• Operating nom. 3000 m
• Storage nom. 3000 m
Relative Humidity (RH)
• Operating & storage: nom 75% @ 35°C (95°F) non-condensing
EMI/EMC
Immunity EN 61000-4-x
• Unit meets following immunity specifications :
3 EN 61000-4-2 (Level 3): Electrostatic Discharge immunity
3 EN 61000-4-3 (Level 3): Radiated, RF immunity, electromagnetic immunity
3 EN 61000-4-4 (Level 3): EFT-Burst immunity
3 EN 61000-4-5 (Level 3): Surge immunity
3 EN 61000-4-6 (Level 2): RF conducted disturbances
3 EN 61000-4-8: Power frequency magnetic immunity
3 EN 61000-4-11: Mains voltage interruptions and variations
Emission
• Unit meets FCC-A
• Unit meets EN 55022 Limit A
Other specifications
MTBF
• 50000 hours
MTTR
• TBD
Barco - LC-5621 - User manual _______________________________________________________ 49
List of abbreviations for all units
10 List of abbreviations for all units
This list of abbreviations is drawn up for all Barco units. Some of these abbreviations are not applicable for the product described in this manual.
µ
µC
A
Conn.
CPLD
CPU
CS
CVBS
D
Db
DC
DCM
DDC
BLOS
BNC
C
CAN
CCFL
CLK
CM
COMM
A
AC
ActEv
ADC
ADP
AGC
AIB
ALC
B
BIB
BIT
BIL
AMLCD
APA
APPLIC
AR coating
Microcontroller
Ampère
Alternating Current
Action and Events
Analog Digital Converter
Auxiliary Display Panel
Automatic Gain Control
Analog Input Board
Ambient Light Controller
Active Matrix Liquid Crystal Display
Automatic Phase Adjust
Application
Anti-Reflective coating
Backlight Inverter Board, Backlight Input Board
Built In Test
Barco Intermodule Link
Backlight OpticaL Stabilisation
Bayonet Neil-Concelman or British Naval Connector
Controller Area Network
Cold Cathode Fluorescent Lamp
CLocK
Console mounted
Communication
Connector
Complex Programmable Logic Device
Central Processing Unit
Composite Sync
Composite Video Burst Sync
Decibels
Direct Current
Display Control Module
Direct Digital Controls
50 _______________________________________________________ Barco - LC-5621 - User manual
List of abbreviations for all units
IOB
IOM
IOPC
IPB
IR
ITO
HMI
HS
I
I2C
I/O
ICD
IIB
IMB
FPGA
FRONT
G
GND
GNDA
GNDD
H
HB
EMC
EMI
ESD
ETI
F
FCC
FIFO
FLIR
DDR SDRAM Double Data Rate Synchronous Dynamic Random Access
Memory
DDS
DEF-STAN
Direct Digital Synthesizer
Defense Standard
DEI
DIB
Diff
DM
DEInterlacer
Digital Input Board
Differential
Display Module
Digital Video Interface DVI
E
EDID
EEPROM
(E²PROM)
Extended Display Identification Data
Electrically Erasable and Programmable Read Only Memory
Electro Magnetic Conductive
Electro Magnetic Immunity
Electrostatic Discharge
Elapsed Time Indication
Federal Communication Commission
First In First Out
Forward Looking InfraRed
Field Programmable Gate Arrays
Assembly of more than 1 I/O connector
Ground
Ground Analog
Ground Digital
High Bright
Human Machine Interface
Horizontal Sync
Inter-IC (bus)
Input/Output
Interface Control Document
Image Input Board
Interface Mother Board
Input/Output Board
Input/Output MIL Connector Board
Input /Output Power Control
Image Processing Board
InfraRed
Indium Tin Oxide
Barco - LC-5621 - User manual _______________________________________________________ 51
List of abbreviations for all units
PIB
PIP
PLL
PM
PSB
PVM
PWM
PWR
Q
R
RAM
MRFD ms
MTBF
MTTR
N
N/A
NTSC
NV or NVIS
NVG
O
OSD
OVERTEMP
P
PAL
PCB
PDB
LUT
LVDS
LVTTL
M
MH
MIL
MHz
MMAN
J
JTAG
K
KEYB
L
LCD
LFC
LRU
Joint Test Action Group
Keyboard
Liquid Crystal Display
Light Flicker Compensation
Line Replaceable Unit
Look-Up Table
Low Voltage Differential Signalling
Low Voltage Transistor-Transistor Logic
Mounting Holes
Military
Mega Hertz
Maintenance Manual
Modular Rugged Flat Display
Millisecond
Mean Time Between Failures
Mean Time To Repair
Not Applicable
National Television Standard Committee
Night Vision
Night Vision Goggle
On Screen Display
Overtemperature
Phase Alternating Line
Printed Circuit Board
Panel Driver Board
Panel Interface Board
Parallel Interface Port
Phase Locked Loop
Panel Module
Power Supply Board
Panel Video Module
Pulse Width Modulation
Power
Random Access Memory
52 _______________________________________________________ Barco - LC-5621 - User manual
List of abbreviations for all units
SVGA
SW
SXGA
S/N
T
TBB
TBD
TBT
SGB
SIB
SMPTE
SOG
SONAR
SRAM
SRU
STD
RX
S
SBB
SDRAM
SECAM
SEL
SER
SG
RADAR
RDM
RFU
RGB
RISC
RM
ROM
RPM
TMAN
TCK
TDI
TDO
Temp
TFT
TIB
TID
TL
TMS
TNC
Radio Detection and Ranging
Rugged Display Module
Reserved for future use
Red Green Blue
Reduced Instruction Set Computer
Rack Mounted
Read-Only Memory
Rotation Per Minute
Receiver
Symbol Generator Bypass Board
Synchronous Dynamic Random Access Memory
Sequential Couleur avec Memoire
Selection
Serial Port
Symbol Generator
Symbol Generator Board
Signal Interface Board
Society of Motion Picture and Television Engineers
Sync On Green
Sound Navigation and Ranging
Static Random Access Memory
Shop Replaceable Unit
Standard
Super Video Graphic Array
Software
Super extended Graphics Array
Serial Number
ThinLITE Backlight Board
To Be Defined
To Be Tested
Technical Manual
Test ClocK
Test Data Input
Test Data Output
Temperature
Thin-Film Transistor
ThinLITE Interface Board
Touch Input Device
Thinlite
Test Mode Select
Threaded Neill Concelman
Barco - LC-5621 - User manual _______________________________________________________ 53
List of abbreviations for all units
VL
VL RX
VM
VPB
Vpp
VS
W
WDI
WUXGA
X
XGA
Y
Y
V
V
VCM
VESA
VGA
VHDL
VHSIC
VID
TRST
TRT
TTL
TX
U
UART
UMAN
UXGA
Test Reset
TRT connectors
Transistor-Transistor Logic
Transmitter
Universal Asynchronous Receiver-Transmitter
User Manual
Ultra eXtended Graphic Array
Volt
Video Control Module
Video Electronics Standards Association
Video Graphic Array
Is the VHSIC Hardware Description Language
Very High Speed Integrated Circuit
Video
Vectorlink
VectorLink Receiver
Vesa Mounted
Video Processing Board
Voltage peak power point
Vertical Sync
Watch Dog Input
Widescreen Ultra eXtended Graphics Array
EXtended Graphic Array
Luminance
54 _______________________________________________________ Barco - LC-5621 - User manual
Table of contents
11 Table of contents
1 About the manual.............................................................................. 3
1.1 Contents of the user manual............................................................... 3
1.3 Notation convention .......................................................................... 4
2 Important notice ............................................................................... 5
2.1 Commercial In Confidence.................................................................. 5
2.3 Federal Communication Commission (FCC) notice.................................. 5
2.4 Disposal information.......................................................................... 5
3 Safety precautions ............................................................................ 7
4 Package & storage............................................................................. 8
4.2 Procedure in case of damaging............................................................ 8
5 About the product ............................................................................. 9
5.2 Recommended use .......................................................................... 10
5.2.1 General precautions for all units ......................................................... 10
6.1 Mounting procedure......................................................................... 11
6.1.1 LC-5621 mounted on stands .............................................................. 11
6.1.2 LC-5621 with VESA compliant mounting solution .................................. 12
6.2 Connecting the signals..................................................................... 13
6.2.2 Detailed connector information........................................................... 14
6.2.2.1 Power connector ................................................................... 14
6.2.2.2 DVI connector ...................................................................... 15
6.2.2.3 Control connector ................................................................. 16
6.3.1 Case 1: Customer buys NVIDIA Quadro FX 4600 .................................. 17
6.3.1.1 System requirements ............................................................ 17
6.3.1.2 NVIDIA Quadro FX 4600 ........................................................ 17
6.3.1.3 Downloading the correct drivers.............................................. 18
6.3.1.4 Installing the drivers ............................................................. 19
6.3.1.5 Connecting the LC-5621 to the workstation .............................. 22
6.3.2 Case 2: Workstation delivered by Barco............................................... 27
7.1 Function of primary controls and indicators......................................... 28
7.1.1.1 Location of the primary controls.............................................. 28
7.1.1.2 Standby button .................................................................... 28
7.1.1.3 Source button ...................................................................... 29
Barco - LC-5621 - User manual _______________________________________________________ 55
Table of contents
7.1.1.4 Mode button......................................................................... 29
7.1.1.5 Enter button ........................................................................ 29
7.1.1.6 Up/Down buttons.................................................................. 29
7.1.1.7 Menu button ........................................................................ 29
7.1.2.1 Location of the primary controls on the IR control ..................... 30
7.1.2.2 F1 button (IR control)............................................................ 30
7.1.2.3 F2 button (IR control)............................................................ 30
7.1.2.4 ADJ button (IR control).......................................................... 30
7.1.2.5 Exit button (IR control).......................................................... 30
7.1.2.6 Enter button (IR control) ....................................................... 31
7.1.2.7 Standby button (IR control) ................................................... 31
7.1.2.8 Up/down buttons (IR control) ................................................. 31
7.1.3.1 Location of the indicators ....................................................... 31
7.1.3.2 Power LED ........................................................................... 32
7.2 Adjusting display settings................................................................. 33
7.2.1 Overview of the on screen display ...................................................... 33
7.2.2 Using the on screen display ............................................................... 34
7.2.2.1 Overview of the key functions................................................. 34
7.2.2.2 Main menu........................................................................... 35
7.2.2.3 Brightness menu................................................................... 35
7.2.2.4 Contrast menu ..................................................................... 36
7.2.2.5 Gamma menu ...................................................................... 36
7.2.2.6 Color temp menu.................................................................. 37
7.2.2.7 User color menu ................................................................... 37
7.2.2.8 Sys info............................................................................... 38
7.2.2.9 Fan status menu................................................................... 38
7.2.2.10 Language menu .................................................................. 39
7.2.2.11 Misc menu ......................................................................... 39
8 Troubleshooting .............................................................................. 40
8.1 Troubleshooting procedure ............................................................... 40
9 Technical specifications .................................................................... 41
9.1 Electro-optical specifications ............................................................. 41
9.1.2.1 Screen dimensions ................................................................ 41
9.1.2.2 Screen specifications ............................................................. 41
9.1.2.3 Light output ......................................................................... 41
9.1.2.4 Contrast ratio....................................................................... 41
9.1.2.5 Resolution ........................................................................... 41
9.1.2.6 Color temperature ................................................................ 42
9.1.2.7 Response time (at 25°C ambient) ........................................... 42
9.1.3.1 DVI connector ...................................................................... 43
9.1.3.2 Control connector ................................................................. 44
9.1.4.1 115 Vac / 220 Vac (50 ~ 60 Hz) supply ................................... 44
9.1.4.2 Power consumption ............................................................... 44
9.1.4.3 Safety ................................................................................. 44
9.1.4.4 Power connector ................................................................... 44
56 _______________________________________________________ Barco - LC-5621 - User manual
Table of contents
9.1.5.2 Controls .............................................................................. 45
9.1.5.3 Indicators ............................................................................ 45
9.2 Mechanical specifications.................................................................. 46
9.2.3.1 VESA compliant mounting solution .......................................... 46
9.2.3.2 Drawings LC-5621 ................................................................ 46
9.3 Environmental specifications............................................................. 49
9.3.1.1 Operating (continuous).......................................................... 49
9.3.1.2 Storage ............................................................................... 49
9.3.4.1 Immunity EN 61000-4-x ........................................................ 49
9.3.4.2 Emission.............................................................................. 49
10 List of abbreviations for all units ...................................................... 50
11 Table of contents............................................................................55
12 List of figures.................................................................................58
Barco - LC-5621 - User manual _______________________________________________________ 57
List of figures
12 List of figures
58 _______________________________________________________ Barco - LC-5621 - User manual
End of document
List of figures
Barco - LC-5621 - User manual _______________________________________________________ 59
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement