Motorola DCT6400 Phase III User guide 41 Pages
advertisement
User Guide
DCT6400 Phase III
High Definition
DVR Cable Terminal
CAUTION
RISK OF ELECTRIC SHOCK
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Graphical symbols and supplemental warning marking locations on bottom of terminal.
WARNING
TO REDUCE THE RISK OF FIRE OR SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
TO PREVENT ELECTRICAL SHOCK, DO NOT USE THIS (POLARIZED) PLUG
WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS
THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
REPAIRS
If you find the unit in need of repair, call Motorola Support at 1-866-668-2271 or
1-866-MOT-BCS1.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article
820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close as possible to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING
Electric service equipment
Ground clamp
Antenna lead in wire
Antenna discharge unit
(NEC Section 810-20)
Grounding clamps
Grounding conductors
(NEC Section 810-21)
Power service grounding electrode system
(NEC Article 250, Part H)
NEC=NATIONAL ELECTRICAL CODE
IMPORTANT SAFETY INSTRUCTIONS
1
Read these instructions.
2
Keep these instructions.
3
Heed all warnings.
4
Follow all instructions.
5
Do not use this apparatus near water.
6
Clean only with dry cloth.
7
Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
8
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11
Only use attachments/accessories specified by the manufacturer.
12
Unplug this apparatus during lightning storms or when unused for long periods of time.
13
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Regulatory Information
Federal Communications Commission Radio and Television Interface Statement for a Class ‘B’
Device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in the residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• Increase the separation between the equipment and the affected receiver
• Connect the equipment on a circuit different from the one the receiver is on
• Ensure that the cover plate for the security card is secured and tight
Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Declaration of Conformity
According to 47 CFR, Parts 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU
Boards and Power Supplies used with Class B Personal Computers, Motorola, Inc., 6450 Sequence
Drive, San Diego, CA 92121, 1-800-225-9446, declares under sole responsibility that the product identifies with 47 CFR Part 2 and 15 of the FCC Rules as a Class B digital device. Each product marketed is identical to the representative unit tested and found to be compliant with the standards.
Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47 CFR
2.909. Operation is subject to the following condition: This device must accept any interference received, including interference that may cause undesired operation. The above named party is responsible for ensuring that the equipment complies with the standards of 47 CFR, Paragraphs 15.101 to 15.109. The
Class B digital apparatus meets all requirements of the Canadian Interface Causing Equipment
Regulations.
Canadian Compliance
This Class B digital device complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Software License
IMPORTANT: PLEASE READ THIS SOFTWARE LICENSE (“LICENSE”) CAREFULLY BEFORE YOU
USE ANY SOFTWARE, FIRMWARE AND RELATED DOCUMENTATION (“SOFTWARE”) PROVIDED
WITH MOTOROLA’S DIGITAL CABLE RECEIVER OR HOME THEATER SYSTEM (EACH SHALL BE
REFERRED TO IN THIS LICENSE AS A “RECEIVER”). BY USING THE RECEIVER AND/OR USING
ANY OF THE SOFTWARE, YOU INDICATE YOUR ACCEPTANCE OF EACH OF THE TERMS OF
THIS LICENSE. UPON ACCEPTANCE, THIS LICENSE WILL BE A LEGALLY BINDING AGREEMENT
BETWEEN YOU AND MOTOROLA. THE TERMS OF THIS LICENSE APPLY TO YOU AND TO ANY
SUBSEQUENT USER OF THIS SOFTWARE.
IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS LICENSE (I) DO NOT USE THE
SOFTWARE AND (II) RETURN THE RECEIVER AND THE SOFTWARE (COLLECTIVELY,
“PRODUCT”), INCLUDING ALL COMPONENTS, DOCUMENTATION AND ANY OTHER MATERIALS
PROVIDED WITH THE PRODUCT, TO YOUR POINT OF PURCHASE OR SERVICE PROVIDER, AS
THE CASE MAY BE, FOR A FULL REFUND.
The Software includes associated media, any printed materials, and any “on-line” or electronic documentation. Software provided by third parties may be subject to separate end-user license agreements from the manufacturers of such Software. The Software is never sold. Motorola licenses the
Software to the original customer and to any subsequent licensee for personal use only on the terms of this License. Motorola and its third party licensors retain the ownership of the Software.
You may:
USE the Software only in connection with the operation of the Product.
TRANSFER the Software (including all component parts and printed materials) permanently to another person, but only if the person agrees to accept all of the terms of this License. If you transfer the
Software, you must at the same time transfer the Product and all copies of the Software (if applicable) to the same person or destroy any copies not transferred.
TERMINATE this License by destroying the original and all copies of the Software (if applicable) in whatever form.
You may not:
(1) Loan, distribute, rent, lease, give, sublicense or otherwise transfer the Software, in whole or in part, to any other person, except as permitted under the TRANSFER paragraph above. (2) Copy or translate the User Guide included with the Software, other than for personal use. (3) Copy, alter, translate, decompile, disassemble or reverse engineer the Software, including but not limited to, modifying the
Software to make it operate on non-compatible hardware. (4) Remove, alter or cause not to be displayed, any copyright notices or startup message contained in the Software programs or documentation. (5) Export the Software or the Product components in violation of any United States export laws.
The Product is not designed or intended for use in on-line control of aircraft, air traffic, aircraft navigation or aircraft communications; or in design, construction, operation or maintenance of any nuclear facility.
MOTOROLA AND ITS THIRD PARTY LICENSORS DISCLAIM ANY EXPRESS OR IMPLIED
WARRANTY OF FITNESS FOR SUCH USES. YOU REPRESENT AND WARRANT THAT YOU SHALL
NOT USE THE PRODUCT FOR SUCH PURPOSES.
Title to this Software, including the ownership of all copyrights, mask work rights, patents, trademarks and all other intellectual property rights subsisting in the foregoing, and all adaptations to and modifications of the foregoing shall at all times remain with Motorola and its third party licensors.
Motorola retains all rights not expressly licensed under this License. The Software, including any images, graphics, photographs, animation, video, audio, music and text incorporated therein is owned by
Motorola or its third party licensors and is protected by United States copyright laws and international treaty provisions. Except as otherwise expressly provided in this License, the copying, reproduction, distribution or preparation of derivative works of the Software, any portion of the Product or the documentation is strictly prohibited by such laws and treaty provisions. Nothing in this License constitutes a waiver of Motorola’s rights under United States copyright law.
This License and your rights regarding any matter it addresses are governed by the laws of the
Commonwealth of Pennsylvania, without reference to conflict of laws principles. THIS LICENSE SHALL
TERMINATE AUTOMATICALLY if you fail to comply with the terms of this License.
Motorola is not responsible for any third party software that is provided as a bundled application, or otherwise, with the Software or that is downloaded to, or otherwise installed on, the Product.
U.S. GOVERNMENT RESTRICTED RIGHTS
The Product and documentation is provided with RESTRICTED RIGHTS. The use, duplication or disclosure by the Government is subject to restrictions as set forth in subdivision (c)(1)(ii) of The Rights in Technical Data and Computer Software clause at 52.227-7013. The contractor/manufacturer is
Motorola, Inc., Broadband Communications Sector, 101 Tournament Drive, Horsham, PA 19044.
Contact Us
For technical support for your DCT6400 cable terminal, call Motorola
Support at 1-866-668-2271 or 1-866-MOT-BCS1.
For questions about your cable TV service, call your cable provider.
For Motorola consumer cable products, education, and support: http://www.motorola.com/broadband
For an overview of high definition television (HDTV): http://broadband.motorola.com/consumers/hdtv/default.asp
___________________________________________________________________________________
Copyright © 2005 Motorola, Inc.
All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation or adaptation) without written permission from Motorola, Inc.
Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Motorola may make improvements or changes in the product(s) described in this manual at any time.
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Dolby Digital manufactured under license from Dolby Laboratories Licensing Corporation. Dolby, Dolby Digital,
ProLogic and the double-D symbol are registered trademarks of Dolby Laboratories. All other product or service names are the property of their respective owners.
© Motorola, Inc. 2005
CONTENTS
DCT6400 Phase III User Guide
Turning Power On and Off ............................................................... 6
Changing Channels .......................................................................... 6
Adjusting the Volume....................................................................... 6
Interactive Program Guide............................................................... 6
Digital Video Recorder (DVR)................................................................. 7
Optimizing Your DCT6400 For High Definition TV............................... 8
On-Screen Graphics ............................................................................. 12
Connecting Your DCT6400................................................................... 13
Video Connection Options ............................................................ 14
Important Safety Considerations .................................................. 15
Connecting Your DCT6400 to aN HDTV – Video Only ....................... 16
Connecting HDTV – Video Only .................................................... 17
Connecting Your DCT6400 to a HDTV – Audio Only ......................... 18
Connecting HDTV – Audio Only.................................................... 19
Connecting Your DCT6400 to an A/V Receiver – Audio Only........... 20
Connecting an A/V Receiver – Audio Only .................................. 21
Connecting Your DCT6400 to a Stereo TV ........................................ 22
Connecting a Stereo TV ................................................................. 23
Connecting Your DCT6400 to a Stereo TV and Stereo VCR ............ 24
Connecting a Stereo TV and Stereo VCR..................................... 25
Connecting Your DCT6400 to an A/V Receiver, TV, and VCR ......... 26
Connecting an A/V Receiver, TV, and VCR.................................. 27
1
Recording Your Connections .............................................................. 28
2
INTRODUCTION
DCT6400 Phase III User Guide
Congratulations on receiving a Motorola DCT6400 Series Phase III High
Definition Advanced DVR Cable Terminal. Motorola has merged the extraordinary features of digital cable – the seemingly endless programming options, interactive program guides, video on demand (VoD), and commercial free, CD quality music – with the flexibility of a dual tuner digital video recorder (DVR) and the incredible picture quality and sound of high definition TV (HDTV). HDTV provides up to twice the color resolution and up to six times the sharpness of standard definition TV.
The DCT6400 enables a direct digital connection to consumer audio and video devices through IEEE-1394 DTV and HDMI interfaces. It contains a hard drive for hours of DVR functionality, including recording high definition (HD) programs and watch and record functionality.
This User Guide introduces the basic features, outlines important safeguards, and provides options for integrating your DCT6400 into your entertainment system. Please take a few moments to read through this
User Guide. The configuration diagrams, on-screen menu description, and troubleshooting section will help you make the most of your home entertainment experience.
To determine which digital cable features are provided in your area, please check with your cable operator. They will be happy to provide instructions for these optional services.
In this guide, “DCT6400” refers to all DCT6400 Series Phase III cable terminals, including the DCT6412 and DCT6416.
They function identically, but have different size hard drives. For example:
Model
Drive
Size
Estimated Recording Hours For
Analog
Channels
Standard Digital
Channels
HDTV
Channels
24 to 32 38 to 73 10 to 15 DCT6412 120 GB
DCT6416 160 GB 35 to 43 55 to 100 14 to 21
All times are approximate.
The actual hours you can record depends on multiple factors.
3
FRONT PANEL
Message Indicator
Lights when message is waiting
POWER switch
Turns unit on or off
MENU switch
Displays menu
INFO switch
Displays current channel and program information
CURSO R
INFO
M ENU
PO WER
M SG S.
O N
USB 2 .0
VIDEO IN
Dua l Tu ne r DVR / HDTV Ca pa ble
L AUDIO IN R
USB 2.0
Connector
AUDIO IN (L/R)*
Audio input from
CD player or tuner
VIDEO IN*
Video input from VCR, camcorder, or other device
CURSOR
Moves cursor around guide and menu screens
POWER indicator
Lights when unit is on
AUDIO IN (R/L)*
Audio input from CD player or tuner
OPTICAL SPDIF
OPTICAL
SPDIF
R
AUDIO
IN L
RF OUT
RF IN 2 CM IN
CABLE
IN
RF IN 1
CABLE IN
Input from cable provider
IR
Enables you to control VCR while recording selected program
(Not supported by all program guides)
IR
S-VIDEO
R AUDIO
OUT
L
RF OUT
Output to TV
S-VIDEO
Output to
TV or VCR
AUDIO OUT (R/L)
Audio output to stereo receiver
4
RECORD Indicator
Lights when DVR is recording
SELECT switch
Selects menu options
GUIDE switch
Displays program guide
OPTION switch
Reserved
DCT6400 Phase III User Guide
CHANNEL
RECO RD
REM OTE
O PTIO N
G UIDE
SELECT
SM ART CARD
DCT6400 III
Display
Displays channel number and time of day
REMOTE indicator
Lights when remote control is in use
CHANNEL
Scrolls up or down through the channels
SMART CARD*
Supports Smart Card functionality
SPDIF (coaxial)
VIDEO IN*
Video input from VCR, camcorder, or other device
VIDEO OUT
Video output to TV, VCR, or other device
ETHERNET*
RJ-45 connector
BACK PANEL
AC Switched Outlet
Provides AC power to TV,
VCR, or other device
SPDIF
Y
IN
Pb
VIDEO
ETHERNET
Pr
OUT
HDMI USB
SATA
TV PASS CARD
IEEE
1394
SWITCHED
105-125V
60Hz
4A MAX
500W MAX
Y Pb Pr
HDTV video output
HDMI
HDTV output
IEEE 1394
HDTV output
SATA
Connects to external hard drive
USB 2.0
Connector
* Your DCT6400 may not support all of the inputs and outputs shown.
5
OPERATION
Turning Power On and Off
Press
POWER on the front panel to turn the DCT6400 on or off. When using the remote control, be sure it is in cable mode by pressing
CABLE before pressing
POWER
.
Changing Channels
You can change channels in two ways:
• Press S or T on the DCT6400 front panel, or press
CHANNEL
+ or - on the remote control to step through the channel selection.
• Enter the number of the channel you wish to view using the number keys on the remote control.
Adjusting the Volume
Press
VOLUME
+ or – on the remote control to adjust the volume. When you adjust the volume, the volume scale is displayed on the screen.
Press
MUTE
on the remote control to turn the sound off and on again.
For best audio quality, use the remote control to set the DCT6400 to approximately ¾ of the maximum volume level and then adjust the audio levels on external devices such as your TV or A/V Receiver.
Interactive Program Guide
The interactive program guide (IPG) displays information about TV programs and enables you to access features such as Parental Control or Pay-Per-View. IPGs can vary with each cable service provider. Refer to your IPG manual for detailed instructions.
6
DIGITAL VIDEO RECORDER (DVR)
DCT6400 Phase III User Guide
The DCT6400 contains a hard drive for the digital video recorder (DVR) to record standard- and high-definition TV (HDTV) programs.
A standard VCR records and plays analog video. DVR records and plays digital video. Unlike an analog tape, the hard drive allows simultaneous recording and playback.
A DVR offers the ability to control your viewing experience by pausing
(time shifting) live TV and providing trick playback modes (pause, fast forward, slow forward, fast rewind, slow rewind). You may experience a slight delay between time shifted and live TV.
With the DCT6400, you can:
Record Programming
Record hours of TV programming. The total hours of recorded content depends on your hard drive capacity and content type (digital, analog, or
HD) that you record.
Maintain a Personal Program Library
Maintain a personal library of recorded programming, accessed using the interactive program guide (IPG).
Control Live TV
Pause, rewind, or fast-forward live TV.
Simultaneously Watch Two Programs
Watch two programs and easily switch between them using the
SWAP key on your remote control. (Dependent upon program guide support.)
Simultaneous Watch and Record
Record one program in the background while viewing another live broadcast at the same time.
Simultaneously Record Two Shows
Record two programs from two different channels at the same time.
Simultaneously Record Two Shows and Watch a Recorded Program
Watch a recorded program while recording up to two other programs at the same time. You can also easily switch viewing the pre-recorded program and either of the programs you’re recording.
7
OPTIMIZING YOUR DCT6400 FOR HIGH DEFINITION TV
The DCT6400 outputs HD video through its Y Pb Pr (component), HDMI, or IEEE 1394 connectors. This section describes how to optimize standard and HD video based on your HDTV and personal preferences.
If you use the IEEE 1394 output, no adjustments to the settings are required.
For a TV with an HDMI connection, be sure the TV is on and connected to the DCT6400 HDMI OUT connector before adjusting the settings.
Motorola recommends using HDMI cables less than 20 meters long.
You can configure the TV type, HDMI and/or Y Pb Pr video output, and closed captioning.
To optimize the output settings:
1
2
Be sure your DCT6400 is plugged into a power outlet and connected to your TV.
Power off the DCT6400 and then immediately press the
MENU
key on the front panel. If your TV is on, the on-screen menu lists the settings you can configure:
HDMI/YpbPr OUTPUT
4:3 OVERRIDE
USER SETTINGS
16:9
1080I
480I
DISABLED
SERVICE SELECTION
ANALOG
DIGITAL
FONT SIZE
FONT COLOR
FONT OPACITY
FONT EDGE TYPE
FONT EDGE COLOR
BACKGROUND COLOR
BACKGROUND OPACITY
SETTINGS
RESTORE ALL DEFAULTS
CC1
PRIMARY LANGUAGE
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
8
DCT6400 Phase III User Guide
Use your remote control or the cursor keys on the front panel to navigate the on-screen display:
• Press ▲ and ▼ keys to highlight the setting you wish to change.
• Press ► key to select an option.
• To exit the setting and move to another setting, use the ▲ and ▼ keys.
If the User Settings menu does not display on the HDTV screen, the TV may not support the default video output setting. Use the front panel LED to adjust the settings as described in “There is no video on the TV screen” in “Troubleshooting.”
For a TV with an HDMI connection, be sure the TV is on and connected to the DCT6400 HDMI OUT connector before adjusting the settings.
The User Settings menu options are:
Setting Description
TV Type
HDMI/YPbPr
Output
Sets the aspect ratio. The front panel display indicates the type you select. Defaults to 16:9. Options are 16:9 for wide screen TVs or 4:3 LETTERBOX or 4:3 PAN/SCAN for standard TVs:
• 4:3 LETTERBOX fits widescreen programming on the screen by placing black bars at the top and bottom.
• 4:3 PAN/SCAN fills the screen by cropping the left and right edges of widescreen programming.
Sets the video display format for the HDMI or component video outputs. The front panel display indicates the format you select. Defaults to 1080i. Options are 1080i, 720p, 480p, or 480i. For HDMI only, additional options you can use to display video on a computer monitor are PC1-VGA
(640x480) and PC2-XVGA (800x600).
Some TVs only support certain display formats. Check your
TV user manual for more information.
If you are not using the HDMI connection, the HDMI/YPbPr
OUTPUT setting displays as YPbPr OUTPUT.
9
Setting Description
4:3 Override
Font Size
Font Style
Sets the display format for 4:3 standard-definition programming. If the YPbPr Output is set to 1080i, 720p, or
480p, this setting defaults to 480i. If the YPbPr Output is set to 480i, this setting defaults to OFF and cannot be changed.
Options are:
•
OFF displays non-high-definition programs having a 4:3 aspect ratio in wide screen format. On an HDTV, black bars display on the left and right of the picture. Selecting
OFF for a 4:3 TV may result in a small picture with black bars around it.
•
480i
displays non-high-definition programs in their original 480i format. Some TVs cannot display 480i format on their component video inputs (YPbPr). Check the TV user manual for more information.
•
480p
converts non-high-definition TV programs to a higher-quality 480p format. Some TVs cannot display
480p format on their component video inputs (YPbPr).
Check the TV user manual for more information.
•
Stretch
automatically stretches all standard definition programming to fill your widescreen display. Stretch can only be selected if you have TV Type set to 16:9.
Closed Caption Turns closed captions off or on. The front panel display indicates the status of the closed captions. Defaults to
DISABLED. Options are ENABLED or DISABLED.
Closed Caption
Turns closed captions off or on. The LED panel displays the status of the closed captions. Defaults to DISABLED.
Options are ENABLED or DISABLED.
Service
Selection
Sets the service used for closed captions:
•
Analog
: CC1, CC2, CC3, CC4, T1, T2, T3, or T4. The default is CC1.
•
Digital:
PRIMARY LANGUAGE, SECONDARY
LANGUAGE, 3, 4, 5, or 6. The default is PRIMARY
LANGUAGE.
Sets the font size for closed captions. Defaults to AUTO.
Options are AUTO, STANDARD, LARGE, or SMALL.
Sets the font style. Defaults to AUTO. Options are AUTO,
MONO SERIF, PROPORTION SERIF, MONO NO SERIF,
PROPORTION NO SERIF, CASUAL, CURSIVE, or SMALL.
10
DCT6400 Phase III User Guide
Setting Description
Font Color
Sets the font color. Defaults to AUTO. Options are AUTO,
WHITE, BLACK, RED, GREEN, BLUE, YELLOW,
MAGENTA, or CYAN.
Font Opacity Sets the opacity. Defaults to AUTO. Options are AUTO,
TRANSPARENT, TRANSLUCENT, SOLID, or FLASHING.
Font Edge Type Sets the edge appearance — AUTO, NONE, RAISED,
DEPRESSED, UNIFORM, LEFT SHADOWED, or RIGHT
SHADOWED. The default is AUTO.
Font Edge Color Sets the edge color — AUTO, WHITE, BLACK, RED,
GREEN, BLUE, YELLOW, MAGENTA, or CYAN. The default is AUTO.
Background
Color
Sets the background color for closed captions. Defaults to
AUTO. Options are AUTO, WHITE, BLACK, RED, GREEN,
BLUE, YELLOW, MAGENTA, or CYAN.
Background
Opacity
Settings
Restore All
Defaults
Sets the background opacity for closed captions. Defaults to
AUTO. Options are AUTO, TRANSPARENT,
TRANSLUCENT, SOLID, or FLASHING.
Sets the default settings for closed captions (AUTO) or the settings you have configured (USER). Defaults to AUTO.
Options are AUTO or USER.
To reset all User Settings to their defaults, select this option and press the ► key.
For HDMI only, when you first connect a TV to the DCT6400 using the HDMI connection, the TV and the DCT6400 exchange information to automatically determine the best possible TV TYPE and HDMI/YPbPr OUTPUT settings. You can change these settings at any time:
• To cause the HDMI TV and DCT6400 to re-exchange information to restore the automatic settings, select
Restore All Defaults with the HDMI connection in place and the TV powered on.
• If you connect another HDMI TV to the DCT6400, select
Restore All Defaults. This causes the TV and DCT6400 to exchange information, enabling settings suited to your new TV.
To exit the menu and save your settings, press the
POWER
or
MENU
key.
11
ON-SCREEN GRAPHICS
The DCT6400 can generate on-screen graphics that overlay the video programming or fill the entire television screen. Common examples include on-screen menus (such as the User Setting menu), closed captions, and interactive program guides. The DCT6400 overlays these graphics whenever you display a menu, enable closed captions, or scroll through a program grid.
On-screen graphics are available for all DCT6400 video outputs except for IEEE 1394.
12
CONNECTING YOUR DCT6400
DCT6400 Phase III User Guide
This section describes connecting the DCT6400 to your home entertainment system.
Instructions and diagrams are included for connections to:
•
High definition television (HDTV)
•
A/V Receiver – Audio
•
Stereo TV
•
Stereo TV and Stereo VCR
•
A/V Receiver, TV, and VCR
Before you move or change components on your entertainment system, review the following:
• For basic cable connections, use 75-ohm coaxial cables equipped with F-type connectors.
• Disconnect power from the cable terminal before connecting or changing cable connections.
For information on connecting for HDTV, see “Video Options” on the next page.
CAUTION!
Do not place anything on top of the cable terminal, especially other home entertainment components. Be sure to provide adequate ventilation to
prevent overheating.
13
Video Connection Options
The DCT6400 offers the following video outputs:
HDTV
Component video, HDMI, or IEEE 1394
Standard Composite video, S-Video, or RF coaxial
To determine the available inputs on your TV, check the manual supplied with the TV or the TV itself.
Use the following guidelines to determine the best video connection for your home entertainment system:
•
Component video (Y Pb Pr) – HDTV and standard
The Y Pb Pr connectors on your DCT6400 provide component video, which is the most widely supported HDTV connection.
•
HDMI or IEEE 1394 – HDTV and standard
HDMI and IEEE 1394 offer higher video quality than component video. If your TV has an HDMI input, use the HDMI connections on your DCT6400 instead of IEEE 1394. Motorola recommends using
HDMI cables less than 20 meters long.
HDMI and IEEE 1394 are video and audio connections. If you use
HDMI or IEEE 1394, no separate audio connection to your TV is required.
HDMI is compatible with DVi. If your TV has a DVI input, you can use an HDMI-to-DVI converter cable to connect to the DCT6400
HDMI connector.
If you use IEEE 1394, on-screen graphics do not display.
•
S-Video – standard only
If your TV has an S-Video input, use S-Video. S-Video is the highest quality standard-definition video output on the DCT6400.
•
Composite video – standard only
If your TV does not have an S-Video input, use the composite video ( VIDEO ) output.
•
RF coaxial – standard only
If your TV only has a coaxial RF input, connect it to the DCT6400
RF OUT connector.
14
DCT6400 Phase III User Guide
Important Safety Considerations
V E N T I L A T E
2
inch space
2 inch
C URSOR
INFO
M ENU
POWER
M SGS.
ON
M U T E
P RECORD
REM OTE
OPTION
GUIDE
SELECT
CHAN NEL
2 inch
USB 2. 0 VIDEO IN L AUDIO IN R
Dual Tune r DVR / HDTV Ca pa ble
SM ART CARD
DCT6416 III
Follow these important safety guidelines when positioning and connecting your cable terminal:
• Position the DCT6400 with at least 2 inches of space above and on all sides
• Do not block the slots and openings
• Do not place anything on top of the DCT6400
• Do not position the DCT6400 in an enclosed space that would restrict airflow around the unit
• Do not position the DCT6400 near any external heat source that could raise the temperature around the unit. Do not place the terminal on top of another heat-producing electronic device.
• Allow for adequate ventilation around the DCT6400 to maintain normal operating temperature. Do not place it in a sealed enclosure without providing for adequate airflow.
• Do not plug the AC power cord into a switched power outlet.
15
CONNECTING YOUR DCT6400 TO AN HDTV – VIDEO ONLY
HDMI connection
Component video connection
IEEE 1394 connection
R
RF IN 2 CM IN
CABLE
RF IN 1
RF OUT
IR
S-VIDEO
R
DCT6400 Phase III
L
SPDIF
IN
L Y Pb
VIDEO
ETHERNET
Pr
OUT
HDMI USB
SATA
TV PASS CARD
SWITCHED
60Hz
Cable in
Either / or
CABL E/
ANT E NNA IN
HDM I
IE EE 1394
HDTV
Co m p o n en t
Vid eo In p u t
Y
P b
P r
16
DCT6400 Phase III User Guide
Connecting HDTV – Video Only
1
2
Connect an RF coaxial cable to the cable wall outlet and the
CABLE IN
connector on the DCT6400.
Connect the HDTV using component video, HDMI, or IEEE 1394.
Component video (Y Pb Pr)
Connect the component video cables to the Y, Pb, and Pr connectors on your DCT6400 and the HDTV.
This connection carries video only. To connect the audio connections for your HDTV, refer to the following page. To connect your audio connections for a home theater receiver, refer to “Connecting Your
DCT6400 to an A/V Receiver – Audio Only.”
HDMI
If your HDTV has a HDMI input, connect an HDMI cable less than 20 meters long to the
HDMI OUT
connector on your HDTV and the DCT6400.
If you use the TV as the primary audio source or your home theater receiver has an HDMI input and output, the HDMI connection carries video and audio.
If your TV has a DVI input, you can use an HDMI-to-DVI converter cable to connect to the DCT6400 HDMI connector.
For information on configuring your DCT6400 settings, see “Optimizing
Your DCT6400 for High Definition TV.”
IEEE 1394
If your HDTV has an IEEE 1394 connector, you can connect an IEEE
1394 cable to the
IEEE 1394
connector on your HDTV and the DCT6400.
If you use the TV as the primary audio source, the IEEE 1394 connection carries video and audio.
If you use the IEEE 1394 connection, on-screen graphics cannot display.
17
CONNECTING YOUR DCT6400 TO A HDTV – AUDIO ONLY
Audio connection
Optical SPDIF connection
SPDIF audio connection
DCT6400 Phase III
R
RF IN 2 CM IN
CABLE
IN
RF IN 1
RF OUT
IR S-VIDEO
R
L SPDIF
L Y
IN
Pb
VIDEO ETHERNET
Pr
OUT
HDMI USB
SATA
TV PASS CARD
IEEE
1394
SWITCHED
60Hz
Cable in
Either / or
CABL E/
ANT ENNA IN
OPT ICAL
SPDIF
HDTV
INPUT
DIGITAL INPUT
COAX
AUDIO L EF T
AUDIO RIGHT
18
DCT6400 Phase III User Guide
Connecting HDTV – Audio Only
Connect the stereo audio cable to the AUDIO R and L connectors on the
DCT6400 and the corresponding connectors on the HDTV.
If your equipment supports it, use the
OPTICAL SPDIF
or coaxial digital
SPDIF
outputs instead of the AUDIO R and L outputs. In most cases,
S/PDIF offers better audio quality, including support for Dolby 5.1
Surround Sound.
HDMI and IEEE1394 carry video and audio. If you connect the DCT6400 to your HDTV using HDMI or IEEE1394, no additional audio connections to the TV are necessary.
For information on configuring your DCT6400 settings, see “Optimizing
Your DCT6400 for High Definition TV.”
19
CONNECTING YOUR DCT6400 TO AN A/V RECEIVER – AUDIO ONLY
Audio connection
SPDIF audio connection
Optical SPDIF connection
DCT6400 Phase III
RF IN 2 CM IN
CABLE
IN
RF IN 1
RF OUT
IR S-VIDEO
R
R
AUDIO
IN
L SPDIF
AUDIO
OUT
L Y
IN
Pb
VIDEO
ETHERNET
Pr
OUT
HDMI USB
SATA
TV PASS CARD
IEEE
1394 SWITCHED
105-125V
60Hz
500W MAX
Either / or
DVD
CABL E/T V
VIDEO 2
R
AUDIO
L
IN
VCR
OUT
VIDEO
VIDEO
S-VIDEO
DIGITAL INPUT
COAX
OPT ICAL
T V/M ONIT OR
OUT PUT
VIDEO S-VIDEO
SPEAKER
CONNECT ORS
A/V receiver
20
DCT6400 Phase III User Guide
Connecting an A/V Receiver – Audio Only
The audio connections options to your A/V receiver or home theater receiver are:
• Optical SPDIF: Connect the optical SPDIF cable to the OPTICAL
SPDIF connector on the DCT6400 and the corresponding connector on the A/V receiver.
• Coaxial SPDIF: Connect the digital audio cable to the SPDIF connector on the DCT6400 and the corresponding connector on the A/V receiver.
• Stereo audio R and L : Connect the stereo audio cable to the
AUDIO R and L connectors on the DCT6400 and the corresponding connectors on the A/V receiver.
If you’re A/V receiver supports it, use the OPTICAL SPDIF or coaxial SPDIF outputs on the DCT6400 instead of its stereo AUDIO R and L outputs. In most cases, S/PDIF offers better audio quality, including support for
Dolby 5.1 Surround Sound.
For information on configuring your DCT6400 settings, see “Optimizing
Your DCT6400 for High Definition TV.”
21
CONNECTING YOUR DCT6400 TO A STEREO TV
RF (75 ohm) connection
S-Video
connection
Video connection
Audio connection
R
RF IN 2 CM IN
CABLE
IN
RF IN 1
RF OUT
IR S-VIDEO
R
DCT6400 Phase III
L
SPDIF
IN
L Y
VIDEO
ETHERNET
Pb Pr
OUT
HDMI USB
SATA
TV PASS CARD
IEEE
1394 SWITCHED
60Hz
Cable in
CABL E/
ANT ENNA IN
Stereo TV
INPUT
S-VIDE O
VIDE O
AUDIO L E F T
AUDIO RIGHT
Either / or
Depending on the TV’s inputs:
1
If possible, use the S VIDEO and AUDIO connectors on the DCT6400.
2
If the TV has no S-Video input, use the composite VIDEO and AUDIO connectors on the DCT6400.
3
If the TV has an RF input only, use the RF OUT connector on the
DCT6400. The RF connection carries video and audio.
22
DCT6400 Phase III User Guide
Connecting a Stereo TV
1
2
3
Connect an RF coaxial cable to the cable wall outlet and the
CABLE IN
connector on the DCT6400.
Connect the stereo audio cable to the AUDIO R and L connectors on the DCT6400 and the corresponding connectors on the stereo TV.
Connect an S-video cable to the
S VIDEO
connectors on the
DCT6400 and the TV. or
Connect a video cable to the VIDEO OUT connector on the DCT6400 and the
VIDEO IN
connector on the TV.
OR
1
2
Connect an RF coaxial cable to the cable wall outlet and the
CABLE IN
connector on the DCT6400.
Connect an RF coaxial cable to the
RF OUT
connector on the
DCT6400 and the RF connector on the TV.
This video connection method does not support HD video. For more information, see “Connecting Your DCT6400 to an HDTV – Video Only.”
23
CONNECTING YOUR DCT6400 TO A STEREO TV AND STEREO VCR
RF (75 ohm) connection
Video connection
Audio connection
RF IN 2 CM IN
R
RF IN 1
RF OUT
IR S-VIDEO
R
DCT6400 Phase III
L
SPDIF
IN
L Y Pb
VIDEO
ETHERNET
Pr
OUT
HDMI USB
SATA
TV PASS CARD
IEEE
1394
SWITCHED
60Hz
Cable in
CABL E/
ANT ENNA IN
To T V
Stereo VCR
INP UT
AUDIO V IDEO
OUT PUT
AUDIO VIDE O
R L R L
CABL E /
ANT E NNA IN
Stereo TV
INPUT
S-VIDE O
VIDE O
AUDIO L E F T
AUDIO RIGHT
24
DCT6400 Phase III User Guide
Connecting a Stereo TV and Stereo VCR
1
2
3
4
5
Connect an RF coaxial cable to the cable wall outlet and the
CABLE IN
connector on the DCT6400.
Connect a stereo audio cable to the
AUDIO OUT R and
L
connectors on the DCT6400 and the
INPUT AUDIO R
and
L
connectors on the stereo VCR.
Connect a video cable to the
VIDEO OUT
connector on the DCT6400 and the
INPUT VIDEO
connector on the stereo VCR.
Connect a stereo audio cable to the
OUTPUT AUDIO R
and
L connectors on the stereo VCR and the
INPUT AUDIO RIGHT
and
LEFT connectors on the stereo TV.
Connect a video cable to the
OUTPUT VIDEO
connector on the stereo
VCR and the
INPUT VIDEO
connector on the stereo TV.
This video connection method does not support HD video. For more information, see “Connecting Your DCT6400 to an HDTV – Video Only.”
25
CONNECTING YOUR DCT6400 TO AN A/V RECEIVER, TV, AND VCR
RF (75 ohm) connection
Video connection
Audio connection
Optical SPDIF connection
RF IN 2 CM IN
DCT6400 Phase III
R
RF IN 1
RF OUT
IR S-VIDEO
R
L SPDIF
IN
L Y Pb
VIDEO ETHERNET
Pr
OUT
HDMI USB
SATA
TV PASS CARD
SWITCHED
60Hz
Cable in
CABL E/
ANT ENNA IN
To T V
Stereo VCR
INPUT
AUDIO VIDEO
OUT PUT
AUDIO VIDEO
R L R L
CABL E/
ANT ENNA IN
Stereo TV
INPUT
S-VIDEO
VIDEO
AUDIO L EF T
AUDIO RIGHT
DVD
CABL E/T V
VIDEO 2
R
AUDIO
L
IN
VCR
OUT
VIDEO
VIDEO S-VIDEO
OPT ICAL
A/V receiver
DIGITAL INPUT
COAX
T V/M ONIT OR
OUT PUT
VIDEO S-VIDEO
SPEAKER
CONNECT ORS
26
DCT6400 Phase III User Guide
Connecting an A/V Receiver, TV, and VCR
1
Connect an RF coaxial cable to the cable wall outlet and the
CABLE IN
connector on the DCT6400.
2
3
4
5
6
7
8
Connect a stereo audio cable to the
AUDIO OUT R
and
L connectors on the DCT6400 and the
INPUT R and
L
connectors on the
A/V receiver.
Connect a video cable to the
VIDEO OUT
connector on the DCT6400 and the
CABLE / TV VIDEO
connector on the A/V receiver.
Connect a stereo audio cable to the
VCR AUDIO OUT R
and
L connectors on the A/V receiver and the
INPUT AUDIO R
and
L connectors on the stereo VCR.
Connect a stereo audio cable to the
OUTPUT AUDIO OUT R
and
L connectors on the stereo VCR and the
VCR AUDIO IN R
and
L connectors on the A/V receiver.
Connect a video cable to the
INPUT VIDEO
connector on the stereo
VCR and the
VIDEO VCR OUT
connector on the A/V receiver.
Connect a video cable to the
OUTPUT VIDEO
connector on the stereo
VCR and the
VIDEO VCR IN
connector on the A/V receiver.
Connect a video cable to the
INPUT VIDEO
connector on the stereo
TV and the
TV / MONITOR OUTPUT
video connector on the A/V receiver.
If you can:
• Use
AUDIO R
OPTICAL SPDIF or coaxial SPDIF outputs instead of the stereo
and
L
outputs. In most cases, S/PDIF offers better audio quality, including support for Dolby 5.1 Surround Sound.
• Use the S-video connections instead of the standard RCA video connections. In most cases, S-video offers better video quality.
This video connection method does not support HD video. For more information, see “Connecting Your DCT6400 to an HDTV – Video Only.”
27
RECORDING YOUR CONNECTIONS
Use this diagram to record connections between your home entertainment components. You can use this diagram to reconnect your system if you move the equipment or add new equipment.
Disconnect the power from the DCT6400 before connecting or changing cable connections. Do not place another component or object on top of the DCT6400.
DCT6400 Phase III
RF IN 2 CM IN
CABLE
IN
RF IN 1
RF OUT
IR
OPTICAL
SPDIF
R
AUDIO
IN
L
SPDIF
IN
S-VIDEO
R AUDIO
OUT
L Y
VIDEO
OUT
ETHERNET
HDMI USB
Pb Pr
SATA
TV PASS CARD
IEEE
1394
105-125V
60Hz
4A MAX
500W MAX
VCR
CABL E/
ANT ENNA IN
To T V
INP UT
AUDIO V IDEO
OUT PUT
AUDIO VIDE O
R L R L
CD IN
AUX IN
R L
IN
TAPE 1
OUT
Stereo receiver
S PE AKER
CONNE CT ORS
CABL E/
ANT ENNA IN L /M ONO
R
OP T ICAL
S PDIF
SPDIF DVI-HDT V
TV
R L
AUDIO IN V IDEO IN S-VIDEO IN HDM I
Y
Pb
Pr
AUDIO OUT VIDE O OUT S-VIDEO OUT IEEE 1394
COAX
AUDIO OUT
OPT ICAL R
DIGITAL ANAL OG
L
DVD
CABL E/T V
V IDEO 2
R
AUDIO
L
IN
V CR
OUT
V IDEO
VIDE O S-V IDEO
A/V receiver
DIGITAL INPUT
COAX
OPT ICAL
T V/M ONIT OR
OUT P UT
VIDE O S -V IDEO
SP EAKE R
CONNECT ORS
DVD
V IDEO
V IDEO OUT
S-V IDEO
28
DATA DEVICES
DCT6400 Phase III User Guide
DCT6400 Phase III
RF IN 2 CM IN
CABLE
IN
RF IN 1
RF OUT
OPTICAL
SPDIF
R
AUDIO
IN L SPDIF
IN
IR S-VIDEO
R AUDIO
OUT
L Y
VIDEO
Pb Pr
OUT
ETHERNET
HDMI USB
SATA
IEEE
1394
TV PASS CARD
105-125V
60Hz
USB devices
External hard drive
Audio/video devices
Do not attempt to connect data devices without contacting your service provider. Advanced data features require the proper application and network infrastructure to operate.
In addition to high quality audio and video, the DCT6400 can deliver high-speed data services such as Internet access, e-mail, IP Telephony,
E-Commerce, and home banking.
The functionality of the illustrated interfaces depends on the services offered by your service provider.
29
TROUBLESHOOTING
Before calling your service provider, review this troubleshooting guide.
This information is to help you quickly solve a problem. If your problem still exists, contact your service provider.
The DCT6400 will not power on
The remote control does not work
The DCT6400 may have received a software update and may not power on while the new software is being installed. Try again in a few minutes.
Verify that the AC power cord is connected to the DCT6400 and an AC outlet. Unplug the DCT6400 from the AC outlet, plug it back in, and then press the
POWER
button.
If the DCT6400 is connected to a switched outlet on another unit, verify that that unit is powered on.
Press the
POWER
button on the DCT6400 front panel instead of the remote control. The batteries in the remote control may be depleted.
Verify that the remote control is in “Cable” mode.
Verify that there are no obstructions between the remote control and the DCT6400. Aim the remote control directly at the DCT6400 front panel, not the TV or VCR.
The angle between the remote control and the DCT6400 may be too large. Stand in front of the DCT6400 and not too far to either side.
Press and release operation keys one at a time, firmly and deliberately.
Try changing channels using the buttons on the
DCT6400 front panel.
Check the batteries in the remote control. Install new batteries if needed.
30
DCT6400 Phase III User Guide
There is no audio when viewing cable channels
There is no audio from the center and/or surround speakers of a home theater receiver connected to the
DCT6400
Verify that the
MUTE
button on the DCT6400 or the remote control was not pressed. Press
MUTE
on the remote control to restore sound.
If the DCT6400 audio output is connected to the TV, verify that the
MUTE
button on the TV was not pressed.
If the DCT6400 audio output is connected to a home theater receiver, verify that the receiver is set to the appropriate input source and the mute button on the receiver was not pressed.
Verify that you used the correct audio cables for the ports.
Verify that the audio cables are firmly connected between the DCT6400 and the audio playback device
(TV, receiver, DVD player, etc.).
Not all Dolby Digital programs feature full 5.1 surround sound. In some cases, the programs may only contain left and right stereo audio.
Verify that the coaxial or optical SPDIF cable is firmly connected to the DCT6400 and the home theater receiver.
Verify that the home theater receiver is set to a surround sound audio mode (Dolby Digital, Dolby Pro Logic
®
II, or
Dolby Pro Logic).
Verify that the receiver is properly configured to work with all connected speakers.
31
There is no video on the TV screen
No graphics or program guides appear on the TV screen
No closed captions display
Verify that the TV is powered on and set to the appropriate input source for the DCT6400.
Verify that the DCT6400 is powered on and tuned to an authorized cable channel.
Verify that all video cables between the DCT6400 and the TV are firmly connected.
Verify that the coaxial cable feed is firmly connected to the DCT6400 and the wall jack.
If the DCT6400 is connected to a home theater unit, verify that the home theater unit is powered on and set to the appropriate input source.
If the DCT6400 is connected to a TV through its HDMI connection, power off the TV and then power off the
DCT6400. Wait one second and then power on the devices.
Not all HDTVs can display every output format (1080i,
720p, 480p, or 480i) available on the DCT6400. To select a different format:
1
2
3
4
Ensure that your DCT6400 is plugged into a power outlet and is turned off.
Press the
MENU
key on the front panel. Your settings are displayed on the DCT6400 front panel display.
Press the ▲ and ▼ keys to display the
HDMI/YPbPr OUTPUT setting.
Press the ► key to cycle through the available output formats until a picture displays on the TV.
If you use the IEEE 1394 connection, on-screen graphics, including closed captions and program guides, are not displayed. If possible, use HDMI or component video instead.
Verify on the User Settings menu that closed captions are enabled on the DCT6400.
Verify that closed captions are enabled on the TV.
32
DCT6400 Phase III User Guide
There are black bars to the right and left of the picture
There are black bars above and below the picture
Wide screen TVs display 4:3 programs in this format unless set to Stretch. Turn on the 4:3 OVERRIDE feature in the User Settings menu. This enables most wide screen TVs to stretch the video to fill the screen (see your TV manual for information about stretching 4:3 video).
If the DCT6400 is connected to a wide screen TV, verify that the TV TYPE is set to 16:9 in the User Settings menu.
Many HD programs are broadcast in pillar-box format with black bars to the left and right of the picture. These programs are broadcast in 16:9 HD formats even though the video is not 16:9.
All 4:3 HDTVs display HD programs in letterbox format
(black bars above and below the picture) because of the shape of the display screen.
Turn on the 4:3 OVERRIDE feature in the User Settings menu. This enables most standard screen TVs to display a full screen picture when the DCT6400 is tuned to a 4:3 program.
Set the TV TYPE to 4:3 Pan-Scan. This enables the
DCT6400 to remove the black bars above and below the picture when possible.
Some SD programs are broadcast in the letterbox format with black bars above and below the picture. Some wide screens TVs offer a zoom feature that may be able to remove the black bars (see your TV manual for information about zooming 4:3 video).
33
There are black bars on all four sides of the picture
The DCT6400 is making a humming noise.
This may occur on a 4:3 TV if the 4:3 OVERRIDE setting is OFF. To set 4:3 SD programming to fill the screen, depending on the capabilities of the TV, set
4:3 OVERRIDE to 480i or 480p.
This may occur on a 16:9 TV if the active video for an SD broadcast is in letterbox format. To confirm, wait for a commercial or look for a graphic, such as a network logo.
If the commercial fills the screen from top to bottom, or the graphic appears below the active video, the program is being letterboxed by the broadcaster. You can minimize this by activating the zoom feature on the TV.
A broadcaster may include black bars on either side of a wide screen broadcast. This is called a “hybrid” aspect ratio and results in a black border surrounding the video on a 4:3 TV. Because this is part of the broadcast, the
DCT6400 cannot correct the video. You may be able to minimize the border using the zoom feature on the TV.
The DCT6400 includes an integrated hard drive and a fan for cooling. During normal operation, the DCT6400 emits a low humming noise, similar to a personal computer. The noise varies in volume occasionally when the speed of the internal fan adjusts to changes in the temperature around the DCT6400. Please note the hard drive will stay on even when the DCT6400 is turned off.
34
advertisement