ClimateMaster | OD Series | Console Series - HVAC Tech Support

TRANQUILITY CONSOLE (TRC) SERIES
SIZE 06 - 18 (1.8kW - 5.3kW)
CONSOLES
R 4 1 0 A - 6 0 H z S TA N D A R D & E X T E N D E D R A N G E
SEIRES )CRT( ELOSNOC YTILIUQNART
)Wk3.5 - Wk8.1( 81 - 60 EZIS
SELOSNOC
E G N A R D E D N E T X E & D R A D N AT S z H 0 6 - A 0 1 4 R
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
TRANQUILITY CONSOLE (TRC) SERIES WITH
EARTHPURE® REFRIGERANT
UNIT FEATURES
The Tranquility series (TRC) console unit provides a high
efficiency WSHP “ductless” solution for spaces where
individual, quiet control of the heating and cooling
system is important. TRC units are especially ideal where
ceiling height and space are limited, or when preserving
the integrity of an existing structure. The TRC series
exceeds ASHRAE 90.1 efficiencies, yet maintains small
cabinet dimensions. Using EarthPure refrigerant, the
Tranquility console not only protects the environment,
it does so while delivering unprecedented comfort,
efficiency, and reliability.
Available in sizes 1/2 ton (1.76 kW) through 1-1/2 tons
(5.3 kW) with numerous cabinet, water piping and
control choices, the TRC series offers a wide range
of units for most any installation. The TRC has an
extended range refrigerant circuit, capable of ground
loop (geothermal) applications as well as water loop
(boiler-tower) applications. Standard features are many.
Microprocessor controls, galvanized steel cabinet,
polyester powder coat paint and TXV refrigerant
metering device are just some of the features of the
flexible TRC series.
ClimateMaster’s exclusive double isolation compressor
mounting system makes the TRC series one of the
quietest console units on the market. Compressors are
mounted on vibration isolation springs to a heavy gauge
mounting plate, which is then isolated from the cabinet
base with rubber grommets for maximized vibration/
sound attenuation. Options such as e-coated air coil,
DDC controls, internal pump and factory-installed water
solenoid valves allow customized design solutions.
• Sizes 06 (1/2 ton, 1.76 kW) through 18 (1-1/2 ton,
5.3 kW)
• Environmentally-friendly EarthPure® (HFC-410A) zero
ozone depletion refrigerant
• High Efficiency Rotary compressors
• Exceeds ASHRAE 90.1 efficiencies
• Two-piece chassis/cabinet design
• Galvanized steel cabinet with durable Polar Ice powder
coat finish and black “matte” finish on subbase
• Slope top/aluminum rigid bar supply air grille
• Unique double isolation compressor mounting for
quiet operation
• TXV metering device
• Extended range (20 to 120°F, -6.7 to 48.9°C) operation
• Advanced digital auto or manual-change-over
unit mounted controls with temperature display and
fault indication
• Remote-mounted controls available
• Microprocessor controls standard (optional DXM and/or
DDC controls)
• LonWorks, BACnet, Modbus and Johnson N2
compatibility options for DDC controls
• Right or left-hand piping arrangement
• Front or bottom return
• Unit Performance Sentinel™ performance
monitoring system
• Eight Safeties Standard
• Wide variety of options including e-coated air coils and
internal pumps
The TRC Series console water-source heat pumps are
designed to meet the challenges of today’s HVAC
demands with a low cost/high value “ductless” solution.
w w w. c l i m a t e m a s t e r. c o m
TRC
3
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Selection Procedure
Reference Calculations
Heating
HE
LWT = EWT GPM x 500
LAT = EAT +
HC
CFM x1.08
Cooling
HR
LWT = EWT +
GPM x 500
LAT (DB) = EAT (DB) -
LC = TC - SC
SC
CFM x1.08
S/T =
SC
TC
Legend and Glossary of Abbreviations
BTUH = BTU( British Thermal Unit) per hour
CFM = airflow, cubic feet/minute
COP = coefficient of performance = BTUH output/BTUH input
DB = dry bulb temperature (°F)
EAT = entering air temperature, Fahrenheit (dry bulb/wet bulb)
EER = energy efficiency ratio = BTUH output/Watt input
EPT = external pipe thread
ESP = external static pressure (inches w.g.)
EWT = entering water temperature
GPM = water flow in U.S. gallons/minute
HE = total heat of extraction, BTUH
HC = air heating capacity, BTUH
HR = total heat of rejection, BTUH
HWC
IPT
KW
LAT
LC
LWT
MBTUH
S/T
SC
TC
WB
WPD
= hot water generator (desuperheater) capacity, Mbtuh
= internal pipe thread
= total power unit input, kilowatts
= leaving air temperature, °F
= latent cooling capacity, BTUH
= leaving water temperature, °F
= 1000 BTU per hour
= sensible to total cooling ratio
= sensible cooling capacity, BTUH
= total cooling capacity, BTUH
= wet bulb temperature (°F)
= waterside pressure drop (psi & ft. of hd.)
Conversion Table - to convert inch-pound (English) to SI (Metric)
TRC
4
Air Flow
Water Flow
Ext Static Pressure
Water Pressure Drop
Airflow (L/s) = CFM x 0.472
Water Flow (L/s) = gpm x 0.0631
ESP (Pa) = ESP (in of wg) x 249
PD (kPa) = PD (ft of hd) x 2.99
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Selection Procedure
Step 1 Determine the actual heating and cooling loads at the
desired dry bulb and wet bulb conditions.
Step 2 Obtain the following design parameters: Entering water
temperature, water flow rate in GPM, air flow in CFM,
water flow pressure drop and design wet and dry bulb
temperatures. Air flow CFM should be between 300
and 450 CFM per ton. Unit water pressure drop should
be kept as close as possible to each other to make
water balancing easier. Go to the appropriate tables
and find the proper indicated water flow and water
temperature.
Step 3 Select a unit based on total and sensible cooling
conditions. Select a unit which is closest to, but no
larger than, the actual cooling load.
Step 4 Enter tables at the design water flow and water
temperature. Read the total and sensible cooling
capacities (Note: interpolation is permissible,
extrapolation is not).
Step 5 Read the heating capacity. If it exceeds the design
criteria it is acceptable. It is quite normal for WaterSource Heat Pumps to be selected on cooling capacity
only since the heating output is usually greater than the
cooling capacity.
Step 6 Determine the correction factors associated with the
variable factors of dry bulb and wet bulb (page 14).
Corrected Total Cooling = tabulated total cooling x wet
bulb correction.
Corrected Sensible Cooling = tabulated sensible
cooling x wet/dry bulb correction.
Step 7 Compare the corrected capacities to the load
requirements. Normally if the capacities are within 10%
of the loads, the equipment is acceptable. It is better
to undersize than oversize, as undersizing improves
humidity control, reduces sound levels and extends the
life of the equipment.
Step 8 When completed, calculate water temperature rise
and assess the selection. If the units selected are not
within 10% of the load calculations, then review what
effect changing the GPM, water temperature and/or air
flow and air temperature would have on the corrected
capacities. If the desired capacity cannot be achieved,
select the next larger or smaller unit and repeat the
procedure. Remember, when in doubt, undersize
slightly for best performance.
Example Equipment Selection For Cooling
Step 1 Load Determination:
Assume we have determined that the appropriate cooling load at
the desired dry bulb 80°F and wet bulb 65°F conditions is as follows:
Total Cooling ...........................................10,200 BTUH
Sensible Cooling ........................................8,350 BTUH
Entering Air Temp ........ 80°F Dry Bulb / 65°F Wet Bulb
Step 2 Design Conditions:
Similarly, we have also obtained the following design parameters:
Entering Water Temp ............................................90°F
Water Flow (Based upon 12°F rise in temp.) 2.3 GPM
Air Flow .........................................................350 CFM
Step 3, 4 & 5 HP Selection:
After making our preliminary selection (TRC12), we enter the tables
at design water flow and water temperature and read Total Cooling,
Sens. Cooling and Heat of Rej. capacities:
Total Cooling ............................................10,800 BTUH
Sensible Cooling ........................................9,200 BTUH
Heat of Rejection .....................................13,900 BTUH
Step 6 & 7 Entering Air and Airflow Corrections:
Next, we determine our correction factors.
Table
Ent Air Air Flow
Corrected
Corrected Total Cooling =
10,800 x 0.976 x 0.954 =
Corrected Sens Cooling =
9,200 x 1.071 x 0.927 =
Corrected Heat of Reject = 13,900 x 0.979 x 0.958 =
10,056
9,134
13,037
Step 8 Water Temperature Rise Calculation & Assessment:
Actual
Temperature Rise
11.3°F
When we compare the Corrected Total Cooling and Corrected
Sensible Cooling figures with our load requirements stated in Step
1, we discover that our selection is within +/- 10% of our sensible
load requirement. Furthermore, we see that our Corrected Total
Cooling figure is slightly undersized as recommended, when
compared to the actual indicated load.
w w w. c l i m a t e m a s t e r. c o m
TRC
5
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
TRC Series Nomenclature
1 2 3
4 5
6
7
8
9
10
11
12
13
14
15
TRC 0 9 A G C A S S C S R S
Model Type
Standard
TRC = Console
S = Standard
Piping Connections
Unit Size
R = Right Piping
L = Left Piping
06, 09, 12, 15, 18
Revision Level
A = Current Revision
Water Circuit Options
Voltage
G = 208-230/60/1
Controls
A = MCO Unit Mounted Tstat w/CXM
B = MCO Unit Mounted Tstat w/DXM
C = ACO Unit Mounted Tstat w/CXM
D = ACO Unit Mounted Tstat w/DXM
R = Remote Mounted Tstat w/CXM
S = Remote Mounted Tstat w/DXM
L = Remote Mounted w/CXM & LON
M = Remote Mounted w/DXM & LON
N = Remote Mounted w/CXM & MPC
P = Remote Mounted w/DXM & MPC
Power Termination
A = Field Connected (Hard Wire)
B = 20Amp Plug & Cord
D = Disconnect Switch & 15Amp Fuse
F = Disconnect Switch (Non Fused)
H = 20Amp Plug, Cord, Receptacle,
Disconnect Switch & 15Amp Fuse
K = 20Amp Plug, Cord, Receptacle &
Disconnect Switch (Non Fused)
Sweat IPT EPT
None
Motorized Water Valve
Autoflow (2.25 Gpm/Ton)
Autoflow (3.0 Gpm/Ton)
Motorized Water Valve & Afr (2.25)
Motorized Water Valve & Afr (3.0)
Secondary Circulation Pump
S
A
B
C
D
E
U
F
G
H
J
K
L
V
M
N
P
Q
R
T
W
Heat Exchanger Options
A = Copper Water Coil w/E-Coated Air Coil
C = Copper Water Coil
J = Cupro-Nickel Water Coil w/E-Coated Air Coil
N = Cupro-Nickel Water Coil
V = Copper Water Coil w/E-Coated Air Coil & Extended Range Insulation
E = Copper Water Coil w/Extended Range Insulation
M = Cupro-nickel Water Coil w/E-Coated Air Coil & Extended Range Insulation
F = Cupro-nickel Water Coil w/Extended Range Insulation
Subbase
S = 5” Subbase
H = 5” Subbase w/Motorized Damper
N = None
Cabinet Insulation
S = Bottom Return
L = Bottom Return w/Locking Control Door
F = Front Return
G = Front Return w/Locking Control Door
N = No Cabinet Chassis Only
Rev.: 12/15/06D
TRC
6
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Performance Data
ARI/ASHRAE/ISO 13256-1
ASHRAE/ARI/ISO 13256-1. English (IP) Units
Water Loop Heat Pump
Model
Cooling 86°F
Capacity
Btuh
EER
Btuh/W
Ground Water Heat Pump
Heating 68°F
Capacity
Btuh
COP
TRC06
TRC09
Cooling 59°F
Capacity
Btuh
EER
Btuh/W
Ground Loop Heat Pump
Heating 50°F
Capacity
Btuh
COP
Cooling 77°F
Heating 32°F
Capacity
Btuh
EER
Btuh/W
Capacity
Btuh
COP
8,800
14.9
7,300
3.3
Data not available at time of publication.
8,600
13.3
11,400
4.6
9,200
18.6
9,500
4.0
TRC12
11,300
13.3
14,900
4.9
12,500
18.7
12,100
4.1
11,800
15.1
9,300
3.7
TRC15
14,100
13.5
18,200
5.1
16,600
21.3
14,800
4.3
15,100
15.8
11,400
3.5
TRC18
16,200
13.0
20,100
4.5
17,600
19.5
16,500
4.0
16,500
15.0
13,200
3.4
Cooling capacities based upon 80.6°F DB, 66.2°F WB entering air temperature
Heating capacities based upon 68°F DB, 59°F WB entering air temperature
All air flow is rated on high speed, Units factory shipped on medium and low motor taps.
All ratings based upon operation at lower voltage of dual voltage rated models
ASHRAE/ARI/ISO 13256-1. Metric (SI) Units
Water Loop Heat Pump
Model
Cooling 30°C
Ground Water Heat Pump
Heating 20°C
Cooling 15°C
Heating 10°C
Capacity
Watts
EER
W/W
Capacity
Watts
COP
Capacity
Watts
TRC09
2,521
3.9
3.341
4.6
2,696
5.5
2,784
TRC12
3,312
3.9
4,367
4.9
3,664
5.5
TRC15
4,132
4.0
5,334
5.1
4,865
6.2
TRC18
4,572
3.8
5,891
4.5
5,158
5.7
TRC06
EER
W/W
Ground Loop Heat Pump
Capacity
Watts
Cooling 25°C
Heating 0°C
Capacity
Watts
EER
W/W
Capacity
Watts
COP
4.0
2,579
4.4
2,140
3.3
3,546
4.1
3,458
4.4
2,726
3.7
4,338
4.3
4,426
4.6
3,341
3.5
4,836
4.0
4,836
4.4
3,869
3.4
COP
Data not available at time of publication.
Cooling capacities based upon 27°C DB, 19°C WB entering air temperature
Heating capacities based upon 20°C DB, 15°C WB entering air temperature
All air flow is rated on high speed, Units factory shipped on medium and low motor taps.
All ratings based upon operation at lower voltage of dual voltage rated models
w w w. c l i m a t e m a s t e r. c o m
TRC
7
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Performance Data
Selection Notes
For operation in the shaded area when water is used
in lieu of an anti-freeze solution, the LWT (Leaving
Water Temperature) must be calculated. Flow must be
maintained to a level such that the LWT is maintained
above 42°F [5.6°C] when the JW3 jumper is not clipped
(see example below). This is due to the potential of the
refrigerant temperature being as low as 32°F [0°C] with
40°F [4.4°C] LWT, which may lead to a nuisance cutout
due to the activation of the Low Temperature Protection.
JW3 should never be clipped for standard range
equipment or systems without antifreeze.
7°F
HR
Heating - EAT 70°F
EER
ended
HC
kW
HE
LAT
COP
5.5
0.50
3.8
91.0
3.22
10.9
26.7
6.0
0.51
4.3
93.1
3.44
10.9
29.9
6.3
0.52
4.5
94.1
3.55
10.9
31.7
6.4
0.52
4.7
94.8
3.62
10.8
22.9
6.9
0.53
5.1
96.5
3.79
10.9
25.8
7.2
0.54
5.4
97.9
3.91
At 50°F EWT (Entering Water Temperature) and 1.5 gpm/
ton, a 3 ton unit has a HE of 22,500 Btuh. To calculate
LWT, rearrange the formula for HE as follows:
10.9
27.4
7.4
0.55
5.6
98.6
3.97
10.6
19.6
7.8
0.56
5.9
100.0
4.10
10.8
22.1
8.2
0.57
6.3
101.6
4.23
HE = TD x GPM x 500, where HE = Heat of Extraction
(Btuh); TD = temperature difference (EWT - LWT) and
GPM = U.S. Gallons per Minute.
10.8
23.4
8.4
0.57
6.5
102.4
4.30
10.4
16.6
8.7
0.58
6.7
103.6
4.39
10 5
18 8
92
0 59
72
105 4
4 53
Example:
TD = HE / (GPM x 500)
TD = 22,500 / (4.5 x 500)
TD = 10°F
LWT = EWT - TD
LWT = 50 - 10 = 40°F
In this example, a higher flow rate will be required for EWTs at or below 50°F without antifreeze. At 2 gpm/ton, the
calculation above results in a TD of 7.5. LWT = 50 - 7.5 = 42.5°F, which is above 42°F EWT, and is acceptable for
this application.
TRC
8
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Performance Data
TRC06
Data for this model was not available at time of publication.
w w w. c l i m a t e m a s t e r. c o m
TRC
9
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Performance Data
TRC09
350 CFM Nominal (Rated) Airflow
*WPD Adder for
Motorized Valve,
TRC09
(Cv = 4.9,
MOPD = 125 psi)
WPD Adder
GPM
PSI
FT
1.1
0.3
0.6
1.6
0.6
1.3
2.2
1.2
2.7
WPD*
EWT
°F
GPM
20
30
40
50
60
70
80
85
90
100
110
120
Performance capacities shown in thousands of Btuh
Cooling - EAT 80/67°F
Sens/Tot
Ratio
EER
HC
6.3
0.67
4.0
86.6
2.72
10.7
20.6
6.9
0.69
4.6
88.2
2.94
0.43
10.4
20.7
7.2
0.69
4.8
89.0
3.04
0.74
0.43
10.2
20.6
7.3
0.69
5.0
89.4
3.11
6.9
0.73
0.47
11.1
19.9
7.9
0.70
5.5
90.9
3.29
6.8
0.73
0.45
10.9
20.5
8.3
0.71
5.9
91.8
3.41
9.2
6.7
0.73
0.45
10.7
20.6
8.5
0.71
6.1
92.4
3.48
2.8
9.5
7.0
0.74
0.51
11.3
18.5
8.9
0.72
6.5
93.7
3.63
2.2
5.1
9.5
6.9
0.73
0.49
11.1
19.5
9.3
0.73
6.9
94.7
3.76
3.8
8.8
9.4
6.9
0.73
0.47
11.1
19.9
9.6
0.73
7.1
95.4
3.84
1.1
1.1
2.5
9.4
7.1
0.76
0.56
11.3
16.7
10.0
0.74
7.5
96.4
3.95
1.6
2.1
4.9
9.5
7.0
0.74
0.53
11.3
17.9
10.4
0.75
7.9
97.6
4.08
2.2
3.7
8.5
9.5
7.0
0.74
0.51
11.2
18.6
10.7
0.75
8.1
98.3
4.16
1.1
1.0
2.3
9.0
7.1
0.79
0.62
11.2
14.5
11.0
0.76
8.4
99.0
4.23
1.6
2.0
4.6
9.3
7.1
0.77
0.58
11.3
15.9
11.4
0.77
8.8
100.2
4.36
2.2
3.5
8.1
9.4
7.1
0.76
0.56
11.3
16.7
11.7
0.77
9.1
101.0
4.43
1.1
1.0
2.3
8.5
7.0
0.82
0.69
10.9
12.3
11.9
0.78
9.2
101.4
4.47
1.6
1.9
4.4
8.8
7.1
0.80
0.65
11.1
13.7
12.3
0.79
9.6
102.6
4.58
2.2
3.2
7.4
9.0
7.1
0.79
0.62
11.2
14.5
12.6
0.80
9.9
103.4
4.64
1.1
1.0
2.2
8.1
6.9
0.84
0.73
10.6
11.1
12.3
0.79
9.6
102.5
4.56
1.6
1.9
4.4
8.5
7.0
0.82
0.68
10.9
12.5
12.7
0.80
10.0
103.6
4.66
2.2
3.1
7.2
8.8
7.0
0.80
0.66
11.0
13.3
13.0
0.81
10.2
104.3
4.71
1.1
0.9
2.1
7.8
6.7
0.87
0.77
10.4
10.1
12.7
0.80
10.0
103.5
4.66
1.6
1.9
4.4
8.2
6.9
0.84
0.72
10.7
11.4
13.1
0.81
10.3
104.6
4.74
2.2
3.0
6.9
8.5
7.0
0.82
0.69
10.9
12.2
13.3
0.82
10.5
105.2
4.77
1.1
0.9
2.1
6.9
6.3
0.91
0.86
9.8
7.9
1.6
1.8
4.2
7.4
6.6
0.89
0.81
10.2
9.1
2.2
2.9
6.7
7.7
6.7
0.87
0.78
10.4
9.9
1.1
0.9
2.1
5.8
5.6
0.97
0.96
9.1
6.0
1.6
1.8
4.2
6.4
6.0
0.94
0.91
9.5
7.0
2.2
2.9
6.7
6.7
6.2
0.92
0.87
9.7
7.7
1.1
0.9
2.1
4.5
4.6
1.00
1.07
8.2
4.2
1.6
1.8
4.2
5.1
5.1
1.00
1.02
8.6
5.0
2.2
2.8
6.5
5.5
5.4
0.98
0.98
8.9
5.6
TC
SC
kW
PSI
FT
2.2
5.0
11.6
1.1
1.6
3.7
9.2
6.7
0.73
0.44
1.6
2.6
6.0
8.9
6.6
0.74
2.2
4.5
10.4
8.8
6.5
1.1
1.4
3.2
9.4
1.6
2.3
5.3
9.3
2.2
4.2
9.7
1.1
1.2
1.6
2.2
HR
Heating - EAT 70°F
Operation Not Recommended
kW
LAT
COP
Operation Not Recommended
Interpolation is permissible; extrapolation is not.
All entering air conditions are 80°F DB and 67°F WB in cooling, and 70°F DB in heating.
ARI/ISO certified conditions are 80.6°F DB and 66.2°F WB in cooling and 68°F DB in heating.
Table does not reflect fan or pump power corrections for ARI/ISO conditions.
All performance is based upon the lower voltage of dual voltage rated units.
Operation below 40°F EWT is based upon a 15% antifreeze solution.
Operation below 60°F EWT requires optional insulated water/refrigerant circuit (standard on residential models).
See performance correction tables for operating conditions other than those listed above.
See Performance Data Selection Notes for operation in shaded areas.
TRC
10
HE
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Performance Data
TRC12
450 CFM Nominal (Rated) Airflow
*WPD Adder for
Motorized Valve,
TRC12
(Cv = 4.9,
MOPD = 125 psi)
WPD Adder
WPD*
EWT
°F
GPM
20
30
Performance capacities shown in thousands of Btuh
Cooling - EAT 80/67°F
TC
SC
Sens/Tot
Ratio
kW
HR
PSI
FT
3.0
7.8
18.0
1.5
2.1
4.9
12.6
8.2
0.65
0.56
14.5
Heating - EAT 70°F
EER
HC
kW
HE
LAT
COP
7.3
0.79
4.7
85.1
2.71
22.4
8.1
0.81
5.4
86.7
2.96
Operation Not Recommended
2.3
4.5
10.4
12.4
8.0
0.65
0.53
14.2
23.3
8.5
0.81
5.7
87.5
3.06
PSI
FT
3.0
6.8
15.7
12.3
8.0
0.65
0.52
14.0
23.6
8.7
0.82
5.9
87.9
3.12
1.5
0.5
1.0
1.5
2.0
4.6
12.7
8.4
0.67
0.61
14.7
20.7
9.4
0.83
6.7
89.4
3.35
2.3
1.2
2.7
2.3
4.2
9.7
12.6
8.2
0.65
0.58
14.6
21.9
9.9
0.83
7.1
90.4
3.48
3.0
2.2
5.0
3.0
6.1
14.1
12.6
8.2
0.65
0.56
14.5
22.4
10.2
0.84
7.3
90.9
3.56
1.5
1.8
4.2
12.5
8.7
0.70
0.67
14.8
18.7
10.8
0.85
8.0
92.3
3.74
2.3
3.8
8.8
12.6
8.5
0.68
0.63
14.8
20.0
11.4
0.86
8.5
93.5
3.91
3.0
5.8
13.4
12.7
8.4
0.67
0.61
14.7
20.7
11.7
0.86
8.8
94.1
4.00
1.5
1.7
3.9
12.1
9.0
0.74
0.73
14.6
16.6
12.2
0.87
9.3
95.1
4.14
2.3
3.7
8.5
12.4
8.8
0.71
0.69
14.7
17.9
12.9
0.87
9.9
96.5
4.32
3.0
5.2
12.0
12.5
8.7
0.70
0.67
14.8
18.6
13.2
0.88
10.2
97.2
4.41
1.5
1.5
3.5
11.6
9.2
0.79
0.80
14.4
14.5
13.6
0.88
10.6
97.9
4.50
2.3
3.5
8.1
12.0
9.1
0.76
0.76
14.5
15.8
14.3
0.89
11.2
99.4
4.69
3.0
4.9
11.3
12.1
9.0
0.74
0.73
14.6
16.5
14.6
0.90
11.6
100.1
4.79
1.5
1.4
3.2
11.0
9.2
0.83
0.89
14.1
12.5
14.8
0.90
11.8
100.5
4.84
2.3
3.2
7.4
11.4
9.2
0.81
0.83
14.3
13.7
15.5
0.91
12.4
101.9
5.01
3.0
4.8
11.1
11.6
9.2
0.79
0.81
14.4
14.4
15.8
0.91
12.7
102.6
5.10
1.5
1.4
3.1
10.7
9.1
0.85
0.93
13.9
11.5
15.4
0.90
12.3
101.6
4.98
2.3
3.1
7.2
11.1
9.2
0.83
0.88
14.1
12.7
16.0
0.91
12.9
102.9
5.13
3.0
4.7
10.7
11.3
9.2
0.81
0.85
14.2
13.4
16.3
0.92
13.1
103.5
5.20
1.5
1.3
3.0
10.4
9.1
0.87
0.98
13.7
10.6
15.9
0.91
12.8
102.7
5.11
2.3
3.0
6.9
10.8
9.2
0.85
0.92
13.9
11.7
16.5
0.92
13.3
103.9
5.25
3.0
4.5
10.4
11.0
9.2
0.84
0.89
14.1
12.3
16.7
0.92
13.6
104.4
5.31
1.5
1.3
3.0
9.7
8.7
0.90
1.08
13.4
9.0
2.3
2.9
6.7
10.1
9.0
0.88
1.02
13.6
9.9
3.0
4.3
9.9
10.3
9.0
0.88
0.99
13.7
10.5
1.5
1.2
2.8
9.0
8.2
0.91
1.20
13.1
7.5
2.3
2.9
6.7
9.4
8.5
0.90
1.13
13.3
8.4
3.0
4.2
9.7
9.6
8.7
0.90
1.09
13.4
8.8
1.5
1.2
2.8
8.4
7.5
0.89
1.33
12.9
6.3
2.3
2.8
6.5
8.7
7.9
0.91
1.25
13.0
7.0
3.0
4.1
9.5
8.9
8.1
0.91
1.21
13.1
7.4
GPM
40
50
60
70
80
85
90
100
110
120
Operation Not Recommended
Interpolation is permissible; extrapolation is not.
All entering air conditions are 80°F DB and 67°F WB in cooling, and 70°F DB in heating.
ARI/ISO certified conditions are 80.6°F DB and 66.2°F WB in cooling and 68°F DB in heating.
Table does not reflect fan or pump power corrections for ARI/ISO conditions.
All performance is based upon the lower voltage of dual voltage rated units.
Operation below 40°F EWT is based upon a 15% antifreeze solution.
Operation below 60°F EWT requires optional insulated water/refrigerant circuit (standard on residential models).
See performance correction tables for operating conditions other than those listed above.
See Performance Data Selection Notes for operation in shaded areas.
w w w. c l i m a t e m a s t e r. c o m
TRC
11
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Performance Data
TRC15
520 CFM Nominal (Rated) Airflow
*WPD Adder for
Motorized Valve,
TRC15
(Cv = 4.9,
MOPD = 125 psi)
WPD Adder
WPD*
EWT
°F
GPM
20
30
Performance capacities shown in thousands of Btuh
Cooling - EAT 80/67°F
TC
SC
Sens/Tot
Ratio
kW
HR
PSI
FT
3.7
5.1
11.8
1.9
1.5
3.5
16.9
11.0
0.65
0.62
19.0
Heating - EAT 70°F
EER
HC
kW
HE
LAT
COP
8.9
0.92
5.8
85.9
2.86
27.1
10.0
0.94
6.8
87.8
3.11
Operation Not Recommended
2.8
3.0
6.9
16.5
10.4
0.63
0.58
18.5
28.6
10.5
0.95
7.2
88.6
3.22
PSI
FT
3.7
4.7
10.9
16.3
10.1
0.62
0.56
18.2
29.2
10.7
0.96
7.5
89.1
3.28
1.9
0.7
1.7
1.9
1.2
2.8
16.9
11.4
0.67
0.70
19.3
24.1
11.7
0.98
8.4
90.8
3.51
2.3
1.7
4.0
2.3
4.2
9.7
12.6
8.2
0.65
0.58
14.6
21.9
9.9
0.83
7.1
90.4
3.48
3.7
3.3
7.6
3.7
4.3
9.9
16.9
11.0
0.65
0.62
19.0
27.1
12.6
0.99
9.2
92.4
3.71
1.9
1.0
2.3
16.6
11.5
0.69
0.79
19.3
21.0
13.4
1.01
10.0
93.9
3.91
2.8
2.3
5.3
16.9
11.5
0.68
0.73
19.4
23.1
14.1
1.02
10.7
95.2
4.06
3.7
3.9
9.0
16.9
11.4
0.67
0.70
19.3
24.2
14.5
1.03
11.0
95.9
4.15
1.9
0.9
2.1
15.9
11.3
0.71
0.89
18.9
17.9
15.2
1.04
11.7
97.1
4.29
2.8
2.1
4.9
16.4
11.4
0.70
0.82
19.2
19.9
16.0
1.05
12.4
98.5
4.46
3.7
3.5
8.1
16.6
11.5
0.69
0.79
19.3
21.0
16.4
1.06
12.8
99.3
4.56
1.9
0.9
2.1
15.0
10.9
0.73
0.99
18.4
15.2
16.9
1.06
13.3
100.1
4.66
2.8
2.0
4.6
15.6
11.2
0.72
0.92
18.8
16.9
17.8
1.08
14.1
101.6
4.84
3.7
3.3
7.6
15.9
11.3
0.71
0.89
18.9
17.9
18.2
1.08
14.5
102.5
4.93
1.9
0.9
2.1
14.0
10.5
0.75
1.10
17.8
12.7
18.5
1.09
14.8
103.0
4.99
2.8
1.8
4.2
14.6
10.8
0.74
1.03
18.2
14.2
19.4
1.10
15.6
104.5
5.17
3.7
3.1
7.2
15.0
10.9
0.73
1.00
18.4
15.0
19.8
1.10
16.1
105.3
5.26
1.9
0.9
2.0
13.4
10.3
0.77
1.16
17.4
11.6
19.2
1.10
15.5
104.3
5.14
2.8
1.8
4.0
14.1
10.5
0.75
1.09
17.8
13.0
20.1
1.11
16.3
105.8
5.31
3.7
3.0
6.9
14.4
10.7
0.74
1.05
18.0
13.8
20.5
1.11
16.7
106.5
5.40
1.9
0.8
1.8
12.9
10.0
0.78
1.22
17.0
10.5
20.0
1.11
16.2
105.6
5.29
2.8
1.7
3.9
13.5
10.3
0.76
1.15
17.5
11.8
20.8
1.12
17.0
107.0
5.45
3.7
2.9
6.7
13.9
10.5
0.75
1.11
17.7
12.5
21.2
1.12
17.3
107.7
5.53
1.9
0.8
1.8
11.7
9.6
0.82
1.35
16.3
8.7
2.8
1.6
3.7
12.4
9.8
0.80
1.27
16.7
9.7
3.7
2.8
6.5
12.7
10.0
0.78
1.23
17.0
10.3
1.9
0.8
1.8
10.6
9.2
0.87
1.48
15.7
7.2
2.8
1.6
3.7
11.2
9.4
0.84
1.40
16.0
8.0
3.7
2.7
6.2
11.5
9.5
0.83
1.37
16.2
8.4
1.9
0.7
1.6
9.6
9.0
0.94
1.62
15.1
5.9
2.8
1.5
3.5
10.1
9.1
0.90
1.54
15.4
6.5
3.7
2.7
6.2
10.4
9.2
0.88
1.51
15.5
6.9
GPM
40
50
60
70
80
85
90
100
110
120
Operation Not Recommended
Interpolation is permissible; extrapolation is not.
All entering air conditions are 80°F DB and 67°F WB in cooling, and 70°F DB in heating.
ARI/ISO certified conditions are 80.6°F DB and 66.2°F WB in cooling and 68°F DB in heating.
Table does not reflect fan or pump power corrections for ARI/ISO conditions.
All performance is based upon the lower voltage of dual voltage rated units.
Operation below 40°F EWT is based upon a 15% antifreeze solution.
Operation below 60°F EWT requires optional insulated water/refrigerant circuit (standard on residential models).
See performance correction tables for operating conditions other than those listed above.
See Performance Data Selection Notes for operation in shaded areas.
TRC
12
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Performance Data
TRC18
620 CFM Nominal (Rated) Airflow
*WPD Adder for
Motorized Valve,
TRC18
(Cv = 4.9,
MOPD = 125 psi)
WPD Adder
GPM
PSI
FT
2.3
0.2
0.6
3.4
0.6
1.3
4.5
1.1
2.5
WPD*
EWT
°F
GPM
20
30
40
50
60
70
80
85
90
100
110
120
Performance capacities shown in thousands of Btuh
Cooling - EAT 80/67°F
TC
SC
Sens/Tot
Ratio
Heating - EAT 70°F
PSI
FT
4.5
7.5
17.3
2.3
2.2
5.1
18.6
12.3
0.66
0.72
3.4
4.4
10.2
17.6
11.6
0.66
4.5
6.9
15.9
16.9
11.1
2.3
2.0
4.6
19.3
3.4
4.1
9.5
19.0
4.5
6.3
14.6
2.3
1.8
4.2
3.4
3.8
8.8
19.3
13.3
0.69
0.84
22.2
23.1
17.7
1.31
13.2
96.4
3.95
4.5
6.0
13.9
19.4
13.2
0.68
0.81
22.1
23.9
17.8
1.31
13.3
96.5
3.97
2.3
1.6
3.7
18.4
13.3
0.72
1.01
21.8
18.2
18.2
1.31
13.8
97.2
4.07
3.4
3.6
8.3
18.9
13.4
0.71
0.94
22.1
20.1
18.5
1.31
14.0
97.6
4.12
4.5
5.6
12.9
19.1
13.5
0.70
0.91
22.2
21.0
18.6
1.31
14.2
97.8
4.15
2.3
1.5
3.5
17.2
12.8
0.75
1.13
21.1
15.3
19.3
1.32
14.8
98.8
4.27
3.4
3.4
7.9
17.9
13.1
0.73
1.06
21.5
17.0
19.7
1.33
15.2
99.5
4.36
4.5
5.2
12.0
18.2
13.3
0.73
1.02
21.7
17.9
20.0
1.33
15.5
99.9
4.40
2.3
1.4
3.2
15.9
12.1
0.76
1.25
20.2
12.7
21.0
1.35
16.4
101.3
4.55
3.4
3.2
7.4
16.7
12.6
0.75
1.18
20.7
14.1
21.8
1.37
17.1
102.6
4.68
4.5
5.0
11.6
17.0
12.7
0.75
1.14
21.0
14.9
22.3
1.38
17.6
103.3
4.75
2.3
1.4
3.1
15.3
11.7
0.77
1.32
19.8
11.6
22.2
1.38
17.6
103.2
4.73
3.4
3.1
7.15
16.0
12.2
0.76
1.25
20.3
12.9
23.3
1.40
18.6
104.9
4.88
4.5
4.9
11.35
16.4
12.4
0.76
1.21
20.6
13.6
24.0
1.42
19.2
105.9
4.97
2.3
1.3
3.0
14.6
11.3
0.77
1.39
19.4
10.5
23.5
1.40
18.7
105.1
4.91
3.4
3.0
6.9
15.3
11.8
0.77
1.32
19.8
11.6
24.9
1.43
20.0
107.2
5.08
4.5
4.8
11.1
15.7
12.0
0.76
1.28
20.1
12.3
25.7
1.45
20.8
108.4
5.18
2.3
1.3
3.0
13.5
10.5
0.78
1.53
18.8
8.8
3.4
2.9
6.7
14.1
10.9
0.78
1.46
19.1
9.6
4.5
4.6
10.6
14.4
11.1
0.77
1.42
19.2
10.1
2.3
1.2
2.8
12.8
9.8
0.77
1.67
18.5
7.6
3.4
2.8
6.5
13.1
10.1
0.77
1.60
18.6
8.2
4.5
4.5
10.4
13.3
10.3
0.78
1.56
18.7
8.5
2.3
1.2
2.8
12.6
9.4
0.74
1.82
18.9
6.9
3.4
2.8
6.5
12.6
9.5
0.76
1.75
18.6
7.2
4.5
4.4
10.2
12.7
9.7
0.76
1.71
18.5
7.4
kW
HR
EER
HC
13.9
1.24
9.8
90.8
3.29
21.0
25.7
15.3
1.28
11.0
92.8
3.51
0.69
19.9
25.3
15.7
1.28
11.3
93.4
3.57
0.66
0.68
19.3
24.8
15.8
1.29
11.5
93.7
3.61
13.2
0.68
0.80
22.1
24.2
16.6
1.30
12.2
94.8
3.74
12.8
0.67
0.75
21.6
25.3
16.9
1.30
12.4
95.2
3.79
18.8
12.5
0.67
0.73
21.3
25.6
17.0
1.31
12.6
95.4
3.81
19.1
13.5
0.70
0.90
22.2
21.4
17.5
1.31
13.0
96.1
3.91
Operation Not Recommended
kW
HE
LAT
COP
Operation Not Recommended
Interpolation is permissible; extrapolation is not.
All entering air conditions are 80°F DB and 67°F WB in cooling, and 70°F DB in heating.
ARI/ISO certified conditions are 80.6°F DB and 66.2°F WB in cooling and 68°F DB in heating.
Table does not reflect fan or pump power corrections for ARI/ISO conditions.
All performance is based upon the lower voltage of dual voltage rated units.
Operation below 40°F EWT is based upon a 15% antifreeze solution.
Operation below 60°F EWT requires optional insulated water/refrigerant circuit (standard on residential models).
See performance correction tables for operating conditions other than those listed above.
See Performance Data Selection Notes for operation in shaded areas.
w w w. c l i m a t e m a s t e r. c o m
TRC
13
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Performance Data
Correction Tables
Air Flow Correction Table
Airflow
Cooling
Heating
% of
Rated
Total
Capacity
Sensible
Capacity
Power
Heat of
Rejection
Heating
Capacity
Power
Heat of
Extraction
73%
0.946
0.898
0.971
0.951
0.967
1.084
0.937
78%
0.954
0.927
0.976
0.958
0.976
1.062
0.954
83%
0.964
0.953
0.981
0.967
0.983
1.042
0.968
89%
0.974
0.974
0.987
0.977
0.990
1.026
0.981
94%
0.987
0.990
0.993
0.988
0.995
1.012
0.991
100%
1.000
1.000
1.000
1.000
1.000
1.000
1.000
106%
1.015
1.002
1.008
1.014
1.004
0.991
1.007
111%
1.031
0.996
1.016
1.028
1.006
0.985
1.011
Entering Air Correction Table
Heating
Cooling
Entering
Air DB°F
Heating
Capacity
Power
Heat of
Extraction
60
1.036
0.910
1.068
65
1.019
0.955
68
1.008
70
Entering
Air WB°F
Total
Capacity
1.035
60
0.926
0.982
1.014
65
1.000
1.000
1.000
75
0.980
1.046
0.964
80
0.960
1.091
0.927
Sensible Cooling Capacity Multiplier Entering DB °F
Power
90
65
70
75
80
80.6
85
0.632
0.820
1.004
1.182
*
*
*
1.003
0.931
0.976
0.615
0.856
1.071
1.095
1.260
*
1.000
0.979
66.2
0.990
0.555
0.807
1.030
1.055
1.224
*
1.000
0.992
67
1.000
0.507
0.765
1.000
1.017
1.188
*
1.000
1.000
70
1.039
0.620
0.865
0.893
1.076
1.252
1.001
1.032
75
1.113
0.566
0.597
0.805
1.013
1.002
1.089
* = Sensible capacity equals total capacity
ARI/ISO/ASHRAE 13256-1 uses entering air conditions of Cooling - 80.6°F DB/66.2°F WB, 1
and Heating - 68°F DB/59°F WB entering air temperature
TRC
14
Heat of
Rejection
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Antifreeze Correction Table
Antifreeze Type
Water
Propylene Glycol
Methanol
Ethanol
Ethylene Glycol
Antifreeze
%
Cooling
Heating
EWT 90°F
EWT 30°F
WPD
Corr. Fct.
EWT 30°F
Total Cap
Sens Cap
Power
Htg Cap
Power
0
1.000
1.000
1.000
1.000
1.000
1.000
5
0.995
0.995
1.003
0.989
0.997
1.070
15
0.986
0.986
1.009
0.968
0.990
1.210
25
0.978
0.978
1.014
0.947
0.983
1.360
5
0.997
0.997
1.002
0.989
0.997
1.070
15
0.990
0.990
1.007
0.968
0.990
1.160
25
0.982
0.982
1.012
0.949
0.984
1.220
5
0.998
0.998
1.002
0.981
0.994
1.140
15
0.994
0.994
1.005
0.944
0.983
1.300
25
0.986
0.986
1.009
0.917
0.974
1.360
5
0.998
0.998
1.002
0.993
0.998
1.040
15
0.994
0.994
1.004
0.980
0.994
1.120
25
0.988
0.988
1.008
0.966
0.990
1.200
w w w. c l i m a t e m a s t e r. c o m
TRC
15
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Blower Performance &
Electrical Data
Blower Performance
Model
Rated
CFM
TRC06
SCFM
Low
Speed
Medium
Speed
High
Speed
Not available at time of publication.
TRC09
350
270
310
350
TRC12
450
290
360
450
TRC15
520
360
440
520
TRC18
620
400
500
620
Fan speed is user selectable
All airflow is rated at lowest Voltage if unit is dual Voltage rated, i.e. 208V for 208-230V units
All units ARI/ISO/ASHRAE 13256-1 rated on high fan speed
All units are designed and rated for zero external static pressure (non-ducted) application
Electrical Data
Model
Voltage
Code
Voltage
Min/Max
Voltage
Compressor
QTY
TRC06
TRC09
TRC12
TRC15
TRC18
TRC
16
RLA
LRA
Fan
Motor
FLA
Total
Unit
FLA
Min
Circuit
Amps
Max
Fuse/
HACR
Data not available at time of publication.
A
115/60/1
104-126
1
8.1
46.5
0.6
8.6
10.7
15
G
208-230/60/1
197-254
1
4.5
23.0
0.4
4.9
6.0
15
E
265/60/1
239-292
1
3.1
24.0
0.4
3.5
4.3
15
A
115/60/1
104-126
1
10.6
55.8
1.0
11.6
14.3
25
G
208-230/60/1
197-254
1
5.2
24.0
0.6
5.8
7.1
15
E
265/60/1
239-292
1
4.2
25.0
0.4
4.6
5.7
15
G
208-230/60/1
197-254
1
6.1
30.0
0.8
6.9
8.4
15
E
265/60/1
239-292
1
4.7
28.5
0.6
5.3
6.5
15
G
208-230/60/1
197-254
1
6.8
38.0
0.7
7.5
9.2
15
E
265/60/1
239-292
1
6.2
29.0
0.6
6.8
8.4
15
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Physical Data
Model
06
09
12
Compressor (1 Each)
Factory Charge R410A (oz) [kg]
15
18
Rotary
*
28 [0.794]
29 [0.822]
37 [1.049]
39 [1.105]
Fan Motor (hp) [W]
*
1/20 [37]
1/12 [62]
1/8 [93]
1/8 [93]
Blower Wheel Size (dia x w) (in) [mm] - Qty 2
*
PSC Fan Motor & Blower (3 Speeds)
5.25 x 6.25 [133 x 159]
Water Connection Size
O.D. Sweat (in) [mm]
*
1/2 [12.7]
3/4 [19.1]
Optional IPT Fittings (in)
*
1/2
3/4
Optional EPT Fittings (in)
*
1/2
3/4
Condensate Connection Size
I.D. Vinyl Hose (In) [mm]
*
5/8 [15.9]
Air Coil Size
Dimensions (h x w) - (in) [mm]
*
8 x 26
[20.3 x 66.0]
10 x 26 [25.4 x 66.0]
10 x 32
[25.4 x 81.2]
Filter Size
Bottom Return (in) [cm]
*
1 - 10 x 30 x 1 [25.4 x 76.2 x 2.5]
2 - 10 x 16 x 1
[25.4 x 40.6 x 2.5]
Front Return (In) [cm]
*
1 - 7 x 29.5 x 1/8 [17.8 x 74.9 x 0.32]
7 x 31.5 x 1/8
[17.8 x 80.0 x .32]
Bottom Return (Std. 5" Base)
(W x H x D) - (In) [cm]
*
48 x 26 x 12 [121.9 x 66.0 x 30.5]
54 x 26 x 12
[137.2 x 66.0 x 30.5]
Front Return (No Subbase)
(W x H x D) - (In) [cm]
*
48 x 21 x 12 [121.9 x 53.3 x 30.5]
54 x 21 x 12
[137.2 x 53.3 x 30.5]
Cabinet Size
Cabinet Size
Weight - Operating, (lbs) [kg]
*
175 [79]
180 [82]
190 [86.2]
220 [99.8]
Weight - Packaged, (lbs) [kg]
*
185 [83.9]
190 [86]
200 [90.8]
232 [105.2]
* Data not available at time of publication.
All units have rubber grommet compressor mountings, isolation plate, and TXV expansion devices.
w w w. c l i m a t e m a s t e r. c o m
TRC
17
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Console Cabinet Dimensions
Size 06 -15
Bottom Return - Left Hand Piping
Left Hand Bottom Return
12.6
(320)
3.5
(88.9)
Discharge
Air
1.5
(38)
30°
Control Access Door
Filter located inside and at
top of air inlet area. Push
tab up and back to release
filter for replacement.
SIDE
VIEW
FRONT VIEW
*25.9
(658)
4.9
(99)
Air
Inlet
AIR INLET AREA
33.5
(851)
1.75
(44.5)
11.5
(292)
12.0
(305)
48.0
(1219)
48.0
(1219)
10.0
(254)
L.H. Pipe &
Electric Area
BOTTOM VIEW
0.75
(19)
1.56
(40)
1 (25)
3.5
(89)
4.5
(114)
1 (25)
REAR
ACCESS
REAR VIEW
21.0
(533)
20.0
(508)
1.63
(41)
DAMPER OPENING*
0.59
(15)
11.75
(298)
9.9
(251)
48.0
(1219)
4.9
(125)
Notes:
All Dimensions are in inches (mm)
Optional autoflow valve, motorized water valve and disconnect box are shown.
TRC
18
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
Rev.: 07/14/06D
4.9
(125)
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Console Cabinet Dimensions
Size 06 - 15
Bottom Return - Right Hand Piping
Left Hand Front Return
12.6
(320)
1.5
(38.1)
3.5
(88.9)
Discharge
Air
30°
Control Access Door
FRONT VIEW
SIDE
VIEW
21.0
(533)
21.0
(533)
Air
7.9
(201) Inlet
48.0
(1219)
43.7
(1110)
12.0
(305)
Filter located behind return
air grille and requires removal of
cabinet front for access.
48.0
(1219)
12.0
(305)
L.H. Pipe &
Electric Area
BOTTOM VIEW
1 (25)
4.5
(114)
1 (25)
REAR
ACCESS
21.0
(533)
REAR VIEW
20.0
(508)
48.0
(1219)
Notes:
All Dimensions are in inches (mm)
Optional autoflow valve, motorized water valve and disconnect box are shown.
w w w. c l i m a t e m a s t e r. c o m
Rev.: 07/14/06D
TRC
19
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Console Cabinet Dimensions
Size 06 -15
Front Return - Left Hand Piping
Right Hand Bottom Return
16.0
(406)
5.0
(127)
3.5
(88.9)
Discharge
Air
30°
Control Access Door
Filter located inside and at
top of air inlet area. Push
tabs up and back to release
filter for replacement.
SIDE
VIEW
FRONT VIEW
*25.9
(658)
4.9
(99)
Air
Inlet
AIR INLET AREA
33.5
(851)
1.75
(44.5)
11.5
(292)
12.0
(305)
48.0
(1219)
48.0
(1219)
BOTTOM VIEW
10.0
(254)
R.H. Pipe &
Electric Area
0.75
(19)
1.56
(40)
1.0 (25)
3.5
(89)
4.5
(114)
1.0 (25)
REAR
ACCESS
REAR VIEW
20.0
(508)
21.0
(533)
1.63
(41)
DAMPER OPENING*
0.59
(15)
11.75
(298)
9.81
(249)
48.0
(1219)
4.9
(125)
Notes:
All Dimensions are in inches (mm)
Optional autoflow valve, motorized water valve and disconnect box are shown.
TRC
20
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
Rev.: 07/14/06D
4.9
(125)
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Console Cabinet Dimensions
Size 06 - 15
Front Return - Right Hand Piping
Right Hand Front Return
16.0
(406)
5.0
(127)
3.5
(88.9)
Discharge
Air
30°
Control Access Door
FRONT VIEW
SIDE
VIEW
21.0
(533)
21.0
(533)
7.9
Air
(201) Inlet
48.0
(1219)
43.7
(1110)
12.0
(305)
Filter located behind return
air grille and requires removal of
cabinet front for access.
48.0
(1219)
R.H. Pipe &
Electric Area
12.0
(305)
1.0 (25)
BOTTOM VIEW
4.5
(114)
1.0 (25)
REAR VIEW
20.0
(508)
21.0
(533)
REAR
ACCESS
48.0
(1219)
Notes:
All Dimensions are in inches (mm).
Optional autoflow valve, motorized water valve and disconnect box are shown.
w w w. c l i m a t e m a s t e r. c o m
Rev.: 07/14/06D
TRC
21
20.50
(521)
TRC
22
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
Optional
Disconnect Box
(mounted to cabinet
not chassis)
Water Connections
5/8" (15.9 mm)
OD Copper,
1/2" IPT or
1/2" EPT
Optional
Motorized
Water Valve
Optional
Autoflow
Valve
3.56
(90)
7.5
(191)
0.87
(22)
3.42
(87)
5.36
(136)
3.01
(76)
4.46
(113)
0.75
(19)
5/8" ID Vinyl Hose
Condensate
*1.94
(49)
*7.06
(179)
*16.66
(423)
Water Out
Water In
3.88
(99)
1.843
(47)
30°
Power Supply
11.54
(293)
3.43
(87)
5.36
(136)
3.01
(76)
3.56
(90)
7.5
(191)
0.87
(22)
5/8" ID Vinyl Hose
Condensate
4.49
(114)
3.50
(89)
0.75
(19)
1.93
(49)
Optional
Motorized
Water Valve
Optional
Autoflow
Valve
Blower Access Panel
20.44
(52)
Rev.: 07/14/06D
0.75
(19)
Compressor
Access
Panel
Control Box
Water Connections
5/8" (15.9 mm)
OD Copper,
1/2" IPT or
1/2" EPT
Optional Fused
Disconnect Box
(mounted to cabinet
not chassis)
Also Available in Non-Fused
40.98
(1041)
Blower Deck
Left Hand Configuration
11.54
(293)
1.843
(47)
3.88
(99)
*7.06
(179)
*1.94
(49)
*16.66
(423)
Power Supply
Water Out
Water In
30°
Right Hand Configuration
Compressor
Access
Panel
Control Box
1.84
(47)
3.28
(83)
Notes:
All Dimensions are in inches (mm)
* For installed dimension, add to dimension shown 2.9" [74mm] with 3" subbase and 4.9" [124mm] for 5" subbase.
Optional autoflow valve, motorized water valve and disconnect box are shown.
Water connection in same location regardless of connection type.
0.75
(19)
Blower Access Panel
Blower Deck
40.98
(1040)
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Console Chassis Dimensions
Size 06 - 15
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Piping Detail
Size 06 - 15
3.28
(83)
5.36
(136)
3.01
(76)
Power Supply
1.84
(47)
30°
Water Out
Water In
Control Box
0.87
(22)
Op
Au
Va
*16.66
(423)
Compressor
Access
Panel
7.5
(191)
4.46
(113)
0.75
(19)
*1.94
(49)
*7.06
(179)
Opt
Mot
Wat
3.56
(90)
1.843
(47)
Condensate
5/8" ID Vinyl Hose
3.88
(99)
11.54
(293)
Water
5/8" (1
OD C
1/2" IP
1/2" E
3.43
(87)
Right Hand Configuration
5.36
(136)
3.01
(76)
Power Supply
Water Out
Water
In
30°
40.98
(1041)
3.50
(89)
1.93
(49)
0.87
(22)
3.42
(87)
Blower Deck
*16.66
(423)
7.5
(191)
*1.94
(49)
3.56
(90)
Blower Access Panel
*7.06
(179)
1.843
(47)
11.54
(293)
3.88
(99)
4.49
(114)
Condensate
0.75
(19)
5/8" ID Vinyl Hose
Left Hand Configuration
w w w. c l i m a t e m a s t e r. c o m
TRC
23
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Console Cabinet Dimensions
Size 18
Bottom Return - Left Hand Piping
Left Hand Bottom Return
12.6
(320)
3.5
(88.9)
Discharge
Air
1.5
(38)
30°
Control Access Door
Filter located inside and at
top of air inlet area. Push
tab up and back to release
filter for replacement.
SIDE
VIEW
FRONT VIEW
*25.9
(658)
4.9
(99)
Air
Inlet
AIR INLET AREA
39.5
(1003)
1.75
(44.5)
11.5
(292)
12.0
(305)
54.0
(1372)
54.0
(1372)
10.0
(254)
L.H. Pipe &
Electric Area
BOTTOM VIEW
0.75
(19)
1.56
(40)
1 (25)
3.5
(89)
4.5
(114)
1 (25)
REAR
ACCESS
REAR VIEW
21.0
(533)
20.0
(508)
1.63
(41)
DAMPER OPENING*
0.59
(15)
11.75
(298)
9.9
(251)
54.0
(1372)
4.9
(125)
Notes:
All Dimensions are in inches (mm)
Optional autoflow valve, motorized water valve and disconnect box are shown.
TRC
24
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
Rev.: 07/14/06D
4.9
(125)
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Console Cabinet Dimensions
Size 18
Bottom Return - Right Hand Piping
Left Hand Front Return
12.6
(320)
1.5
(38.1)
3.5
(88.9)
Discharge
Air
30°
Control Access Door
FRONT VIEW
SIDE
VIEW
21.0
(533)
21.0
(533)
Air
7.9
(201) Inlet
54.0
(1372)
48.0
(1219)
12.0
(305)
Filter located behind return
air grille and requires removal of
cabinet front for access.
54.0
(1372)
12.0
(305)
L.H. Pipe &
Electric Area
BOTTOM VIEW
1 (25)
4.5
(114)
1 (25)
REAR
ACCESS
21.0
(533)
REAR VIEW
20.0
(508)
54.0
(1372)
Notes:
All Dimensions are in inches (mm)
Optional autoflow valve, motorized water valve and disconnect box are shown.
w w w. c l i m a t e m a s t e r. c o m
Rev.: 07/14/06D
TRC
25
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Console Cabinet Dimensions
Size 18
Front Return - Left Hand Piping
Right Hand Bottom Return
16.0
(406)
5.0
(127)
3.5
(88.9)
Discharge
Air
30°
Control Access Door
Filter located inside and at
top of air inlet area. Push
tabs up and back to release
filter for replacement.
SIDE
VIEW
FRONT VIEW
*25.9
(658)
4.9
(99)
Air
Inlet
AIR INLET AREA
39.5
(1003)
1.75
(44.5)
11.5
(292)
12.0
(305)
54.0
(1372)
54.0
(1372)
BOTTOM VIEW
10.0
(254)
R.H. Pipe &
Electric Area
0.75
(19)
1.56
(40)
1.0 (25)
3.5
(89)
4.5
(114)
1.0 (25)
REAR
ACCESS
REAR VIEW
20.0
(508)
21.0
(533)
1.63
(41)
DAMPER OPENING*
0.59
(15)
11.75
(298)
9.81
(249)
54.0
(1372)
4.9
(125)
Notes:
All Dimensions are in inches (mm)
Optional autoflow valve, motorized water valve and disconnect box are shown.
TRC
26
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
Rev.: 07/14/06D
4.9
(125)
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Console Cabinet Dimensions
Size 18
Front Return - Right Hand Piping
Right Hand Front Return
16.0
(406)
5.0
(127)
3.5
(88.9)
Discharge
Air
30°
Control Access Door
FRONT VIEW
SIDE
VIEW
21.0
(533)
21.0
(533)
7.9
Air
(201) Inlet
54.0
(1372)
48.0
(1219)
12.0
(305)
Filter located behind return
air grille and requires removal of
cabinet front for access.
54.0
(1372)
R.H. Pipe &
Electric Area
12.0
(305)
1.0 (25)
BOTTOM VIEW
4.5
(114)
1.0 (25)
REAR VIEW
20.0
(508)
21.0
(533)
REAR
ACCESS
54.0
(1372)
Notes:
All Dimensions are in inches (mm).
Optional autoflow valve, motorized water valve and disconnect box are shown.
w w w. c l i m a t e m a s t e r. c o m
Rev.: 07/14/06D
TRC
27
20.50
(521)
TRC
28
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
Optional
Disconnect Box
(mounted to cabinet
not chassis)
Water Connections
5/8" (15.9 mm)
OD Copper,
1/2" IPT or
1/2" EPT
Optional
Motorized
Water Valve
Optional
Autoflow
Valve
3.56
(90)
7.5
(191)
0.87
(22)
3.42
(87)
5.36
(136)
3.01
(76)
4.46
(113)
0.75
(19)
5/8" ID Vinyl Hose
Condensate
*1.94
(49)
*7.06
(179)
*16.66
(423)
Water Out
Water In
3.88
(99)
1.843
(47)
30°
Power Supply
11.54
(293)
3.43
(87)
5.36
(136)
3.01
(76)
3.56
(90)
7.5
(191)
0.87
(22)
5/8" ID Vinyl Hose
Condensate
4.49
(114)
3.50
(89)
0.75
(19)
1.93
(49)
Optional
Motorized
Water Valve
Optional
Autoflow
Valve
Blower Access Panel
20.44
(52)
Rev.: 07/14/06D
0.75
(19)
Compressor
Access
Panel
Control Box
Water Connections
5/8" (15.9 mm)
OD Copper,
1/2" IPT or
1/2" EPT
Optional Fused
Disconnect Box
(mounted to cabinet
not chassis)
Also Available in Non-Fused
46.98
(1193)
Blower Deck
Left Hand Configuration
11.54
(293)
3.88
(99)
1.843
(47)
*7.06
(179)
*1.94
(49)
*16.66
(423)
Power Supply
Water Out
Water In
30°
Right Hand Configuration
Compressor
Access
Panel
Control Box
1.84
(47)
3.28
(83)
Notes:
All Dimensions are in inches (mm)
* For installed dimension, add to dimension shown 2.9" [74mm] with 3" subbase and 4.9" [124mm] for 5" subbase.
Optional autoflow valve, motorized water valve and disconnect box are shown.
Water connection in same location regardless of connection type.
0.75
(19)
Blower Access Panel
Blower Deck
46.98
(1193)
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Console Chassis Dimensions
Size 18
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Piping Detail
Size 18
3.28
(83)
5.36
(136)
3.01
(76)
Power Supply
1.84
(47)
30°
Water Out
Water In
Control Box
0.87
(22)
*16.66
(423)
Compressor
Access
Panel
7.5
(191)
4.46
(113)
0.75
(19)
*1.94
(49)
*7.06
(179)
O
M
W
3.56
(90)
1.843
(47)
Condensate
5/8" ID Vinyl Hose
3.88
(99)
11.54
(293)
Wa
5/8
OD
1/2
1/2
3.43
(87)
Right Hand Configuration
5.36
(136)
3.01
(76)
Power Supply
Water Out
Water
In
30°
46.98
(1193)
3.50
(89)
1.93
(49)
0.87
(22)
3.42
(87)
Blower Deck
*16.66
(423)
7.5
(191)
*1.94
(49)
3.56
(90)
Blower Access Panel
*7.06
(179)
1.843
(47)
11.54
(293)
3.88
(99)
4.49
(114)
Condensate
0.75
(19)
5/8" ID Vinyl Hose
Left Hand Configuration
w w w. c l i m a t e m a s t e r. c o m
TRC
29
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
TRC Series Wiring Diagram Matrix
Only CXM and DXM diagrams, with a representative diagram of LON and MPC Options are presented in this submittal.
Other diagrams can be located online at www.climatemaster.com using the part numbers presented below.
Model
TRC06 TRC18
Refrigerant
Wiring Diagram
Part Number
R410A
96B0099N50
R410A
96B0099N03
R410A
96B0099N04
R410A
R410A
R410A
96B0100N03
R410A
96B0100N04
R410A
96B0100N05
Electrical
Control
Agency
ACO/MCO
CSA
REM
CSA
LON
CSA
96B0099N05
MPC
CSA
96B0100N50
ACO/MCO
CSA
REM
CSA
LON
CSA
MPC
CSA
115/60/1,
208-230/60/1,
CXM
265/60/1
115/60/1,
208-230/60/1,
265/60/1
DXM
All wiring diagrams available at www.climatemaster.com.
TRC
30
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Typical Wiring Diagram
Manual & Auto Change Over TRC Units
With CXM Controller
w w w. c l i m a t e m a s t e r. c o m
TRC
31
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Typical Wiring Diagram
Remote Mounted Thermostat TRC Units
With CXM Controller
TRC
32
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Typical Wiring Diagram
TRC Units
With CXM & LON Controller
w w w. c l i m a t e m a s t e r. c o m
TRC
33
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Typical Wiring Diagram
TRC Units
With CXM & MPC Controller
TRC
34
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Typical Wiring Diagram
Manual & Auto Change Over TRC Units
With DXM Controller
w w w. c l i m a t e m a s t e r. c o m
TRC
35
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Typical Wiring Diagram
Remote Mounted Thermostat TRC Units
With DXM Controller
TRC
36
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Typical Wiring Diagram
TRC Units
With DXM & LON Controller
w w w. c l i m a t e m a s t e r. c o m
TRC
37
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Typical Wiring Diagram
TRC Units
With DXM & MPC Controller
TRC
38
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Tranquility Console (TRC) Series 60Hz
Engineering Specifications Rev.: 04/02/07
General:
Furnish and install ClimateMaster “Console” Water Source Heat Pumps, as indicated on the plans. Equipment shall be completely
assembled, piped and internally wired. Capacities and characteristics as listed in the schedule and the specifications that follow.
Console Water Source Heat Pumps:
Units shall be supplied completely factory built for an entering water temperature range from 20º to 120ºF (-6.7º to 48.9ºC) as
standard. Equivalent units from other manufacturers can be proposed provided approval to bid is given 10 days prior to bid
closing. All equipment listed in this section must be rated and certified in accordance with American Refrigeration Institute /
International Standards Organization (ARI / ISO) and Environmental Testing Laboratories for United States and Canada (ETL-US-C).
The units shall have ARI / ISO and ETL-US-C labels.
Basic Construction:
Console Units shall have one of the following air flow and piping arrangements: Front Inlet/Right-hand Piping; Front Inlet/
Left-hand piping; Bottom Inlet/Right-hand piping; or Bottom Inlet/Left-hand piping as shown on the plans. If units with
these arrangements are NOT used, the contractor is responsible for any extra costs incurred by other trades. If other
arrangements make servicing difficult, the contractor must provide access panels and clear routes to ease service. Architect/
Engineer must approve any changes in layout.
The cabinet, wall mounting hardware and subbase shall be constructed of heavy gauge galvanized steel with a baked polyester
powder coat paint finish. Corrosion protection system shall meet the stringent 1000 hour salt spray test per ASTM B117. Unit
corrosion protection must meet these stringent requirements or unit(s) will not be accepted. Color will be Polar Ice. Both sides
of the steel shall be painted for added protection. Additionally, the wall mounting hardware shall have welded corner bracing. The
easily removable cabinet enclosure allows for easy service to the chassis, piping compartment and control compartment.
All interior surfaces shall be lined with 1/4 inch (6.4mm) thick, dual density, 2 lb/ft3 (32 kg/m3) acoustic flexible blanket type glass
fiber insulation with a non-woven, anti-microbial treated mat face. Insulation placement shall be designed in a manner that will
eliminate any exposed edges to prevent the introduction of glass fibers into the air stream.
Standard insulation must meet NFPA Fire Hazard Classification requirements 25/50 per ASTM E84, UL 723, CAN/ULC S102-M88
and NFPA 90A requirements; air erosion and mold growth limits of UL-181; stringent fungal resistance test per ASTM-C1071 and
ASTM G21; and shall meet zero level bacteria growth per ASTM G22. Unit insulation must meet these stringent requirements
or unit(s) will not be accepted.
The cabinet shall have a 30º sloped top with aluminum rigid bar type discharge grille. Aluminum discharge grille shall be
anodized charcoal grey in color including hinged control door. Cabinet shall have rounded edges (0.325 inch / 8.255 mm
minimum radius) on all exposed corners for safety and esthetic purposes. Units not having sloped top and rounded corners
(0.325 inch / 8.255 mm minimum) on front, side, top slope, and top corners shall not be accepted.
Return Air Filter shall be 1” (25.4mm) fiberglass disposable type media for bottom return units (units with subbase) or 1/8”
(3.2mm) permanent cleanable type media for front return type units.
Option: The unit shall be provided with a keyed lock on the control access door.
Option: The unit shall be provided with a motorized outside air damper and damper assembly, factory mounted and wired.
Option: The unit shall be provided without a subbase (5 inch / 127mm high subbase is standard).
Option: The unit shall include a front return air grille integrally stamped into Cabinet (no subbase allowed).
Option: The unit shall include an optional architectural-style field installed return air grille to help conceal the subbase return air
opening (units with bottom return only).
Option: The unit shall be supplied with extended range Insulation option, which adds closed cell insulation to internal water lines,
and provides insulation on suction side refrigeration tubing including refrigerant to water heat exchanger.
Fan and Motor Assembly:
Fan and motor assembly shall be assembled on a slide out fan deck with quick electrical disconnecting means to provide and
facilitate easy field servicing. The fan motor shall be multi-speed, permanently lubricated, PSC type, with internal thermal
w w w. c l i m a t e m a s t e r. c o m
TRC
39
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
overload protection. Units supplied without permanently lubricated motors must provide external oilers for easy service. The fan
motor shall include a torsionally flexible motor mounting system or saddle mount system with resilient rings to inhibit vibration
induced high noise levels associated with “hard wire belly band” motor mounting. The airflow rating of the unit shall be based on
a wet coil and a clean filter in place. Ratings based on a dry coil and / or no filter shall NOT be acceptable.
Refrigerant Circuit:
All units shall contain an EarthPure® (HFC 410A) sealed refrigerant circuit including a high efficiency rotary compressor designed
for heat pump operation, a thermostatic expansion valve for refrigerant metering, an enhanced corrugated aluminum lanced fin
and rifled copper tube refrigerant to air heat exchanger, reversing valve, coaxial (tube in tube) refrigerant to water heat exchanger,
and safety controls including a high pressure switch, low pressure switch (loss of charge), water coil low temperature sensor, and
air coil low temperature sensor. Access fittings shall be factory installed on high and low pressure refrigerant lines to facilitate field
service. Activation of any safety device shall prevent compressor operation via a microprocessor lockout circuit. The lockout circuit
shall be reset at the thermostat or at the contractor supplied disconnect switch. Units that cannot be reset at the thermostat
shall not be acceptable.
Hermetic compressors shall be internally sprung. The compressor shall have a dual level vibration isolation system. The
compressor will be mounted on computer selected vibration isolation grommets to a large heavy gauge compressor mounting
tray plate, which is then isolated from the cabinet base with rubber grommets for maximized vibration attenuation. Compressor
shall have thermal overload protection. Compressor shall be located in an insulated compartment away from air stream to
minimize sound transmission.
Refrigerant to air heat exchangers shall utilize enhanced corrugated lanced aluminum fins and rifled copper tube construction
rated to withstand 625 PSIG (4309 kPa) refrigerant working pressure. Refrigerant to water heat exchangers shall be of copper
inner water tube and steel refrigerant outer tube design, rated to withstand 625 PSIG (4309 kPa) working refrigerant pressure and
450 PSIG (3101 kPa) working water pressure. The refrigerant to water heat exchanger shall be “electro-coated” with a low cure
cathodic epoxy material a minimum of 0.4 mils thick (0.4 – 1.5 mils range) on all surfaces. The black colored coating shall provide
a minimum of 1000 hours salt spray protection per ASTM B117-97 on all external steel and copper tubing. The material shall be
formulated without the inclusion of any heavy metals and shall exhibit a pencil hardness of 2H (ASTM D3363-92A), crosshatch
adhesion of 4B-5B (ASTM D3359-95), and impact resistance of 160 in-lbs (184 kg-cm) direct (ASTM D2794-93).
Refrigerant metering shall be accomplished by thermostatic expansion valve only. Expansion valves shall be dual port balanced
types with external equalizer for optimum refrigerant metering. Units shall be designed and tested for operating ranges of
entering water temperatures from 20° to 120°F (-6.7° to 48.9°C). Reversing valve shall be four-way solenoid activated refrigerant
valve, which shall default to heating mode should the solenoid fail to function. If the reversing valve solenoid defaults to cooling
mode, an additional low temperature thermostat must be provided to prevent over-cooling an already cold room.
Option: The unit will be supplied with cupro nickel coaxial water to refrigerant heat exchanger.
Option: The unit will be supplied with internally factory mounted two-way water valve for variable speed pumping requirements.
A factory-mounted or field-installed high pressure switch shall be installed in the water piping to disable compressor
operation in the event water pressures build due to water freezing in the piping system.
Option: The unit will be supplied with internally factory mounted automatic water flow regulators.
Option: The unit will be supplied with internally mounted secondary pump for primary/secondary applications, specifically onepipe systems.
Option: The unit shall be supplied with extended range Insulation option, which adds closed cell insulation to internal water lines,
and provides insulation on suction side refrigeration tubing including refrigerant to water heat exchanger.
Option: The refrigerant to air heat exchanger shall be “electro-coated” with a low cure cathodic epoxy material a minimum of
0.4 mils thick (0.4 – 1.5 mils range) on all surfaces. The black colored coating shall provide a minimum of 1000 hours salt
spray protection per ASTM B117-97 on all galvanized end plates and copper tubing, and a minimum of 2000 hours of salt
spray on all aluminum fins. The material shall be formulated without the inclusion of any heavy metals and shall exhibit a
pencil hardness of 2H (ASTM D3363-92A), crosshatch adhesion of 4B-5B (ASTM D3359-95), and impact resistance of 160
in-lbs (184 kg-cm) direct (ASTM D2794-93).
Piping:
Water piping shall terminate in the same location regardless of the connection and valve options.
Option: Threaded EPT copper fittings (sweat connections are standard).
TRC
40
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Option: Threaded IPT copper fittings (sweat connections are standard).
Drain Pan:
The drain pan shall be constructed of galvanized steel and have a powder coat paint application to further inhibit corrosion. This
corrosion protection system shall meet the stringent 1000 hour salt spray test per ASTM B117. If plastic type material is used,
it must be HDPE (High Density Polyethylene) to avoid thermal cycling shock stress failure over the lifetime of the unit. Stainless
Steel materials are also acceptable. Drain pan shall be fully insulated. Drain outlet shall be located at pan as to allow complete
and unobstructed drainage of condensate. The unit as standard will be supplied with solid-state electronic condensate overflow
protection. Mechanical float switches will NOT be accepted.
Electrical:
Unit controls shall be located under the hinged control door in the sloped top grille. Operating controls shall consist of slide
switches to select “OFF”, “HEAT,” “COOL,” “AUTO” (when equipped with auto change-over option – “AUTO” is not available
for standard manual change-over controls), Fan “AUTO” (fan cycles with compressor), Fan “ON” (continuous fan), Fan “LO” (low
speed fan), and Fan “HI” (high speed fan). Temperature adjustment shall be accomplished via two push buttons, one labeled with
an arrow up, and the other labeled with an arrow down. Controls shall include an LCD display for display of temperature and set
point. Units without an LCD display shall not be accepted.
A control box shall be located above the unit compressor compartment and shall contain operating controls as outlined in the
paragraph above, 24VAC transformer, double-pole compressor relay, and solid-state controller for complete unit operation.
Reversing valve and fan motor wiring shall be routed through this electronic controller. Units shall be name-plated for use with time
delay fuses or HACR circuit breakers. A unit-mounted digital thermostat with a remote bulb measuring return air temperature shall
control the compressor operation for heating and cooling. Control shall be equipped with a fan switch (provides options to cycle fan
with compressor or provide continuous fan) and a fault indicator light. Units without a fault indicator light shall not be accepted.
Option: Digital ACO unit mounted thermostat (MCO is standard).
Option: Provisions for remote thermostat (unit mounted is standard).
Option: Disconnect Switch, Non-Fused.
Option: Disconnect Switch, Fused with 15A fuse.
Option: 20A power plug/cord.
Option: 20A plug, cord, receptacle, disconnect switch, fused with 15A fuse.
Option: 20A plug, cord, receptacle, disconnect switch, non fused.
Solid State Control System (CXM):
Units shall have a solid-state control system. Units utilizing electro-mechanical control shall not be acceptable. The control
system microprocessor board shall be specifically designed to protect against building electrical system noise contamination,
EMI, and RFI interference. The control system shall interface with a heat pump type thermostat. The control system shall have the
following features:
a.
b.
c.
d.
e.
f.
g.
h.
i.
j.
k.
l.
m.
n.
Anti-short cycle time delay on compressor operation.
Random start on power up mode.
Low voltage protection.
High voltage protection.
Unit shutdown on high or low refrigerant pressures.
Unit shutdown on low water temperature.
Condensate overflow electronic protection.
Option to reset unit at thermostat or disconnect.
Automatic intelligent reset. Unit shall automatically reset the unit 5 minutes after trip if the fault has cleared. If a fault occurs
3 times sequentially without thermostat meeting temperature, then lockout requiring manual reset will occur.
Ability to defeat time delays for servicing.
Light emitting diode (LED) on circuit board to indicate high pressure, low pressure, low voltage, high voltage, low water/air
temperature cut-out, condensate overflow, and control voltage status.
The low-pressure switch shall not be monitored for the first 120 seconds after a compressor start command to prevent
nuisance safety trips.
24V output to cycle a motorized water valve or other device with compressor contactor.
Unit Performance Sentinel (UPS). The UPS warns when the heat pump is running inefficiently.
w w w. c l i m a t e m a s t e r. c o m
TRC
41
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
o.
p.
Water coil low temperature sensing (selectable for water or anti-freeze).
Air coil low temperature sensing.
NOTE: Units not providing the 8 safety protections of anti-short cycle, low voltage, high voltage, high refrigerant pressure,
low pressure (loss of charge), air coil low temperature cut-out, water coil low temperature cut-out, and condensate
overflow protections will not be accepted.
Option: Enhanced solid state control system (DXM)
This control system features two stage control of cooling and two stage control of heating modes for exacting temperature and
dehumidification purposes.
This control system coupled with a multi-stage thermostat will better dehumidify room air by automatically running the heat
pump’s fan at lower speed on the first stage of cooling thereby implementing low sensible heat ratio cooling. On the need for
higher cooling performance the system will activate the second stage of cooling and automatically switch the fan to the higher
fan speed setting. This system may be further enhanced with a humidistat. Units not having automatic low sensible heat ratio
cooling will not be accepted; as an alternate a hot gas reheat coil may be provided with control system for automatic activation.
Control shall have all of the above mentioned features of the CXM control system along with the following expanded features:
a.
b.
c.
d.
e.
f.
g.
h.
i.
j.
k.
l.
m.
n.
o.
Removable thermostat connector.
Night setback control.
Random start on return from night setback.
Minimized reversing valve operation (Unit control logic shall only switch the reversing valve when cooling is demanded for
the first time. The reversing valve shall be held in this position until the first call for heating, ensuring quiet operation and
increased valve life.).
Override temperature control with 2-hour (adjustable) timer for room occupant to override setback temperature at
the thermostat.
Dry contact night setback output for digital night setback thermostats.
Ability to work with heat pump or heat/cool (Y, W) type thermostats.
Ability to work with heat pump thermostats using O or B reversing valve control.
Emergency shutdown contacts.
Boilerless system heat control at low loop water temperature.
Ability to allow up to 3 units to be controlled by one thermostat.
Relay to operate an external damper.
Ability to automatically change fan speed from multistage thermostat.
Relay to start system pump.
75 VA control transformer. Control transformer shall have load side short circuit and overload protection via a built in
circuit breaker.
Remote Service Sentinel (CXM/DXM):
Solid state control system shall communicate with thermostat to display (at the thermostat) the unit status, fault status, and
specific fault condition, as well as retrieve previously stored fault that caused unit shutdown. The Remote Service Sentinel allows
building maintenance personnel or service personnel to diagnose unit from the wall thermostat. The control board shall provide a
signal to the thermostat fault light, indicating a lockout. Upon cycling the G (fan) input 3 times within a 60 second time period, the
fault light shall display the specific code as indicated by a sequence of flashes. A detailed flashing code shall be provided at the
thermostat LED to display unit status and specific fault status such as over/under voltage fault, high pressure fault, low pressure
fault, low water temperature fault, condensate overflow fault, etc. Units that do not provide this remote service sentinel shall
not be acceptable.
Option: Lonworks interface system
Units shall have all the features listed above (either CXM or DXM) and the control board will be supplied with a LONWORKS
interface board, which is LONMark certified. This will permit all units to be daisy chained via a 2-wire twisted pair shielded cable.
The following points must be available at a central or remote computer location:
a.
Space temperature
b. Leaving water temperature
c.
Discharge air temperature
d. Command of space temperature setpoint
e. Cooling status
f.
Heating status
g. Low temperature sensor alarm
h. Low pressure sensor alarm
TRC
42
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
i.
j.
k.
l.
m.
n.
o.
p.
q.
r.
High pressure switch alarm
Condensate sensor alarm
Hi/low voltage alarm
Fan “ON/AUTO” position of space thermostat as specified above
Unoccupied / occupied command
Cooling command
Heating command
Fan “ON / AUTO” command
Fault reset command
Itemized fault code revealing reason for specific shutdown fault (any one of 7)
This option also provides the upgraded 75VA control transformer with load side short circuit and overload protection via a built in
circuit breaker.
Option: MPC (Multiple Protocol Control) interface system
Units shall have all the features listed above (either CXM or DXM) and the control board will be supplied with a Multiple Protocol
interface board. Available protocols are BACnet MS/TP, Modbus, or Johnson Controls N2. The choice of protocol shall be field
selectable/changeable via the use of a simple selector switch. Protocol selection shall not require any additional programming or
special external hardware or software tools. This will permit all units to be daisy chain connected by a 2-wire twisted pair shielded
cable. The following points must be available at a central or remote computer location:
a.
Space temperature
b. Leaving water temperature
c.
Discharge air temperature
d. Command of space temperature setpoint
e. Cooling status
f.
Heating status
g. Low temperature sensor alarm
h. Low pressure sensor alarm
i.
High pressure switch alarm
j.
Condensate overflow alarm
k.
Hi/low voltage alarm
l.
Fan “ON/AUTO” position of space thermostat as specified above
m. Unoccupied / occupied command
n. Cooling command
o. Heating command
p. Fan “ON / AUTO” command
q. Fault reset command
r.
Itemized fault code revealing reason for specific shutdown fault (any one of 7)
This option also provides the upgraded 75VA control transformer with load side short circuit and overload protection via a built in
circuit breaker.
Warranty:
Climate Master shall warranty equipment for a period of 12 months from start up or 18 months from shipping (which ever occurs first).
Option: Extended 4-year compressor warranty covers compressor for a total of 5 years.
Option: Extended 4-year refrigeration circuit warranty covers coils, reversing valve, expansion valve and compressor for a total of
5 years.
Option: Extended 4-year control board warranty covers the CXM/DXM control board for a total of 5 years.
FIELD INSTALLED OPTIONS
Hose Kits:
Hoses shall be 1 foot (31cm) long, braided stainless steel; fire rated hoses complete with adapters. Only fire rated hoses will be
accepted. Note: Threaded connection piping option must be ordered for hose kit connections.
Option: 2 foot (61cm) hose lengths instead of standard 1 foot (31cm) length.
Valves:
The following valves are available and will be shipped loose:
a.
Ball valve; bronze material, standard port full flow design, IPT connections.
w w w. c l i m a t e m a s t e r. c o m
TRC
43
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
b.
c.
d.
e.
Ball valve with memory stop and PT Port; standard port full flow design, IPT connections.
“Y” strainer with cap; bronze material, IPT connections.
“Y” strainer with blowdown valve; bronze material, IPT connections.
Motorized water valve; slow acting, 24v, IPT connections.
Hose Kit Assemblies:
The following assemblies ship with the valves already assembled to the hose described:
a.
Supply and return hoses having ball valve with PT port.
b. Supply hose having ball valve with PT port; return hose having automatic flow regulator valve (Measureflo) with PT ports, and
ball valve.
c.
Supply hose having “Y” strainer with blowdown valve, and ball valve with PT port; return hose having automatic flow
regulator (Measureflo) with PT ports, and ball valve.
Thermostats:
The thermostat shall be a ClimateMaster mechanical or electronic type thermostat as selected below with the described features
(Note: “Remote mounted thermostat” control option must be selected for the console unit):
a.
b.
c.
d.
e.
f.
g.
h.
TRC
44
Single Stage Standard Manual Changeover (ATM11C01)
Thermostat shall be a single-stage, vertical mount, manual changeover with HEAT-OFF-COOL system switch and fan ONAUTO switch. Thermostat shall have a mechanical temperature indicator and set point indication. Thermostat shall only
require 4 wires for connection. Mercury bulb thermostats are not acceptable.
Single Stage Digital Manual Changeover with Two-Speed Fan Control (ATM11C03) – Recommended for Console RemoteMount Thermostat (DXM required)
Thermostat shall be a single-stage, digital, manual changeover with HEAT-OFF-COOL system switch, fan ON-AUTO switch,
and fan LO-HI switch. Thermostat shall have an LCD display with temperature and set-point(s) in ºF or ºC. The Thermostat
shall provide permanent memory of set-point(s) without batteries. A fault LED shall be provided to display specific fault
condition. Thermostat shall come standard with remote temperature sensor, but may be operated with internal sensor if
desired via installation of a jumper.
Single Stage Digital Auto or Manual Changeover (ATA11U01)
Thermostat shall be a single-stage, digital, auto or manual changeover with HEAT-OFF-COOL-AUTO system switch and fan
ON-AUTO switch. Thermostat shall have an LCD display with temperature and set-point(s) in ºF or ºC. The Thermostat shall
provide permanent memory of set-point(s) without batteries. A fault LED shall be provided to display specific fault condition.
Thermostat shall provide temperature display offset for custom applications.
Single Stage Digital Automatic Changeover with Two-Speed Fan Control (ATA11C04) – Recommended for Console RemoteMount Thermostat (DXM required)
Thermostat shall be a single-stage, digital, auto or manual changeover with HEAT-OFF-COOL-AUTO system switch, fan
ON-AUTO switch, and fan LO-HI switch. Thermostat shall have an LCD display with temperature and set-point(s) in ºF or ºC.
The Thermostat shall provide permanent memory of set-point(s) without batteries. A fault LED shall be provided to display
specific fault condition. Thermostat shall come standard with remote temperature sensor, but may be operated with internal
sensor if desired via installation of a jumper.
Multistage Digital Automatic Changeover (ATA22U01)
Thermostat shall be multi-stage (2H/2C), manual or automatic changeover with HEAT-OFF-COOL-AUTO system settings and
fan ON-AUTO settings. Thermostat shall have an LCD display with temperature, set-point(s), mode, and status indication.
The temperature indication shall be selectable for ºF or ºC. The thermostat shall provide permanent memory of set-point(s)
without batteries. A fault LED shall be provided to indicate specific fault condition(s). Thermostat shall provide temperature
display offset for custom applications. Thermostat shall allow unit to provide better dehumidification with optional DXM
controller by automatically using lower fan speed on stage 1 cooling (higher latent cooling) as main cooling mode, and
automatically shifting to high speed fan on stage 2 cooling.
Single Stage Manual Changeover Programmable 5/2 Day (ATP11N01)
Thermostat shall be 5 day/2 day programmable (with up to 4 set points per day), single stage (1H/1C), manual changeover
with HEAT-OFF-COOL system settings and fan ON-AUTO settings. Thermostat shall have an LCD display with temperature,
set-point(s), mode, and status indication. The temperature indication shall be selectable for ºF or ºC. The thermostat shall
provide permanent memory of set-point(s) without batteries. Thermostat shall provide convenient override feature to
temporarily change set point.
Multistage Automatic or Manual Changeover Programmable 5/2 Day (ATP21U01)
Thermostat shall be 5 day/2 day programmable (with up to 4 set points per day), multi-stage (2H/1C), automatic or manual
changeover with HEAT-OFF-COOL-AUTO system settings and fan ON-AUTO settings. Thermostat shall have an LCD display
with temperature, set-point(s), mode, and status indication. The temperature indication shall be selectable for ºF or ºC. The
thermostat shall provide permanent memory of set-point(s) without batteries. Thermostat shall provide convenient override
feature to temporarily change set point.
Multistage Automatic or Manual Changeover Programmable 7 Day (ATP32U01)
Thermostat shall be 7 day programmable (with up to 4 set points per day), multi-stage (3H/2C), automatic or manual
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
i.
changeover with HEAT-OFF-COOL-AUTO system settings and fan ON-AUTO settings. Thermostat shall have a blue backlit
dot matrix LCD display with temperature, set-points, mode, and status indication. The temperature indication shall be
selectable for ºF or ºC. Time display shall be selectable for 12 or 24 hour clock. Fault identification shall be provided (when
used with ClimateMaster CXM or DXM controls) to simplify troubleshooting by providing specific unit fault at the thermostat
with red backlit LCD during unit lockout. The thermostat shall provide permanent memory of set-points without batteries.
Thermostat shall provide heating set-point range limit, cooling set-point range limit, temperature display offset, keypad
lockout, dead-band range setting, and inter-stage differential settings. Thermostat shall provide progressive recovery to
anticipate time required to bring space temperature to the next programmed event. Thermostat shall provide an installer
setup for configuring options and for setup of servicing contractor name and contact information. Thermostat shall allow the
use of an accessory remote and/or outdoor temperature sensor (AST008). Thermostat navigation shall be accomplished via
five buttons (up/down/right/left/select) with menu-driven selections for ease of use and programming.
Multistage Automatic or Manual Changeover Programmable 7 Day with Humidity Control (ATP32U02)
Thermostat shall be 7 day programmable (with up to 4 set points per day), multi-stage (3H/2C), automatic or manual
changeover with HEAT-OFF-COOL-AUTO system settings and fan ON-AUTO settings. Separate dehumidification and
humidification set points shall be configurable for discreet outputs to a dehumidification option and/or an external
humidifier. Installer configuration mode shall allow thermostat dehumidification mode to operate with ClimaDry reheat or
with ECM fan dehumidification mode via settings changes. Thermostat shall have a blue backlit dot matrix LCD display
with temperature, relative humidity, set-points, mode, and status indication. The temperature indication shall be selectable
for ºF or ºC. Time display shall be selectable for 12 or 24 hour clock. Fault identification shall be provided (when used with
ClimateMaster CXM or DXM controls) to simplify troubleshooting by providing specific unit fault at the thermostat with red
backlit LCD during unit lockout. The thermostat shall provide permanent memory of set-points without batteries. Thermostat
shall provide heating set-point range limit, cooling set-point range limit, temperature display offset, keypad lockout,
dead-band range setting, and inter-stage differential settings. Thermostat shall provide progressive recovery to anticipate
time required to bring space temperature to the next programmed event. Thermostat shall provide an installer setup for
configuring options and for setup of servicing contractor name and contact information. Thermostat shall allow the use of
an accessory remote and/or outdoor temperature sensor (AST008). Thermostat navigation shall be accomplished via five
buttons (up/down/right/left/select) with menu-driven selections for ease of use and programming.
DDC Sensors:
ClimateMaster wall mounted DDC sensor to monitor room temperature and interfaces with optional interface system described
above. Several types as described below:
a.
Sensor only with no display (LON and MPC).
b. Sensor with override (LON only).
c.
Sensor with setpoint and adjustment override (MPC only).
d. Sensor with setpoint and adjustment override, LCD display, status/fault indication (LON and MPC).
w w w. c l i m a t e m a s t e r. c o m
TRC
45
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Section Change Log
Date:
TRC
46
Item:
Action:
05/23/07
Specifications
Updated for new Safety Agency
05/23/07
Decoder
Updated decoder
01/01/07
First Published
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
THE SMART SOLUTION FOR ENERGY EFFICIENCY
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
Notes:
w w w. c l i m a t e m a s t e r. c o m
TRC
47
C L I M AT E M A S T E R W AT E R - S O U R C E H E AT P U M P S
Tr a n q u i l i t y C o n s o l e ( T R C ) S e r i e s
R e v. : 0 5 / 2 3 / 0 7 D
TRC
48
C l i m a t e M a s t e r W a t e r- S o u r c e H e a t i n g a n d C o o l i n g S y s t e m s
Download PDF

advertising