INSTALLATION
FRONT LED SIGNAL CONVERSION—2 CIRCUIT
PARTS INCLUDED
2 Deep Dish LED Signals
1
1
3 Connector
1 Dielectric Grease
1
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING K
ϋ
RYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDING
THE USE AND CARE OF THIS PRODUCT.
WARNING! THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING
ATTENTION! This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality.
TOOLS SUGGESTED
Phillips Screwdriver, Pliers, and a Wire stripper
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
STEP 1
STEP 2
STEP 3
THE CONTENTS DESCRIBED HEREIN CAN RESULT IN
POTENTIAL DEATH OR SERIOUS INJURY
Read and understand all steps in the instructions before starting the
Installation. Park the motorcycle on a hard, level surface; turn off the ignition and allow the engine to cool.
Using a Phillips Screwdriver, remove the screw from the underside of your OEM turn signal assembly and set it aside, it will be reused.
Remove the OEM lens being careful not to lose the threaded clip on the OEM lens tab or the rubber gasket. Gasket needs to remain in the housing. Pic. 1
PIC 1
Notice Tab Positions
5033
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS [email protected] or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products sold hereunder, shall be free of defects in materials and workmanship for a period of one (1) year from the date of purchase by the consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s).
● The product must be properly installed, maintained and operated under normal conditions.
● Küryakyn makes no warranty, expressed or implied, with respect to any gold plated products.
● Küryakyn shall not be liable for any consequential and incidental damages, including labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breech of contract or duty between
Küryakyn and a customer.
● Küryakyn products are often intended for use in specific applications. Küryakyn makes no warranty if a Küryakyn product is used in applications other than intended.
● Küryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. Components of Küryakyn products containing L.E.D.s will be warranted for defects in materials and workmanship for 3 years from the date of purchase.
● Küryakyn makes no warranty of any kind in regard to other manufacturer¹s products distributed by Küryakyn. Küryakyn will pass on all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but ultimately, responsibility for disposition of the warranty claim lies with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.
-cont.- OEM GASKET
5033-21MC-1010
STEP 4
STEP 5
STEP 6
STEP 7
STEP 8
STEP 9
Use pliers to grip and remove the OEM heat shield/reflector.
Remove the threaded clip from the OEM bezel tab and install on the new LED Conversion tab.
Remove stock bulb, notice the position of the pins on the connector before installing new LED
Conversion. Insert connector into the terminal socket.
Insert the LED conversion into the signal housing while making sure the mounting tab and clip line up with the fastener hole in the lower turn signal housing.
NOTE: Use dielectric grease on all electrical connections.
Reinstall the screw removed in STEP 2 to secure the new conversion to the turn signal housing.
Repeat steps 1-8 for the opposite side. Secure all fasteners.
ATTENTION!
It is the installer’s responsibility to ensure that all of the fasteners
(including pre-assembled) are tightened before operation of the motorcycle. Küryakyn will not issue a warranty on components lost due to improper installation. Periodic
maintenance may be required.
LOAD EQUALIZER
STEP 10 If you are not using a Kuryakyn Run, Turn, Brake controller, you will need to cut the white plug off the end of the Load Equalizer.
STEP 11 Depending on the model of your bike, the load equalizer needs to be installed where your main wiring harness and the rear fender harness are connected. This is typically located under the seat or side cover.
STEP 12
STEP 13
One violet wire from the load equalizer will go to the right turn signal positive wire.
One violet wire from the load equalizer will go to the left turn signal positive wire.
STEP 14 The black wire from the load equalizer should be connected to a confirmed ground wire or clean chassis ground.
STEP 15 Use the supplied connectors to mate all the wires from the Load Equalizer to the wires located on the bike.
Ride On!
PAGE
2
FRONT LED SIGNAL CONVERSION—2 CIRCUIT INSTALLATION
