TELETEK - CA 62 uzstādīšanas instrukcija (EN)

TELETEK - CA 62 uzstādīšanas instrukcija (EN)
Alarm Control Panel
CA62
Installation and Programming
Manual
WARNING
This manual contains information on limitations regarding product use and function and information
on the limitations as to liability of the manufacturer. The entire manual should be carefully read.
The information in this manual is a subject to change without notice!
C
Guarantee
During the guarantee period the manufacturer shall, at its sole discretion, replace or repair any defective product when it is returned
to the factory. All parts replaced and/or repaired shall be covered for the remainder of the original guarantee, or for ninety (90) days,
whichever period is longer. The original purchaser shall immediately send manufacturer a written notice of the defective parts or
workmanship, which written notice must in all cases be received prior to expiry of the guarantee.
International Guarantee
Foreign customers shall enjoy the same guarantee rights as those enjoyed by any customer in Bulgaria, except that manufacturer
shall not be liable for any related customs duties, taxes or VAT, which may be payable.
Guarantee Procedure
This guarantee will be granted when the appliance in question is returned. The manufacturer shall accept no product whatsoever, of
which no prior notice has been received.
Conditions for waiving the guarantee
This guarantee shall apply to defects in products resulting only from improper materials or workmanship, related to its normal use. It
shall not cover:
• Damages resulting from transportation and handling;
• Damages caused by natural calamities, such as fire, floods, storms, earthquakes or lightning;
• Damages caused by incorrect voltage, accidental breakage or water; beyond the control of the manufacturer;
• Damages caused by unauthorized system incorporation, changes, modifications or surrounding objects:
• Damages caused by peripheral appliances (unless such peripheral appliances have been supplied by the manufacturer:
• Defects caused by inappropriate surrounding of installed products;
• Damages caused by failure to use the product for its normal purpose; Damages caused by improper maintenance;
• Damages resulting from any other cause, bad maintenance or product misuse.
In the case of a reasonable number of unsuccessful attempts to repair the product, covered by this guarantee, the manufacturer’s liability shall be limited to the replacement of the product as the sole compensation for breach of the guarantee. Under no circumstances
shall the manufacturer be liable for any special, accidental or consequential damages, on the grounds of breach of guarantee, breach
of agreement, negligence, or any other legal notion.
Waiver
This Guarantee shall contain the entire guarantee and shall be prevailing over any and all other guarantees, explicit or implicit (including any implicit guarantees on behalf of the dealer, or adaptability to specific purposes), and over any other responsibilities or liabilities
on behalf of the manufacturer. The manufacturer does neither agree, nor empower, any person, acting on his own behalf, to modify
or alter this Guarantee, nor to replace it with another guarantee, or another liability with regard to this product.
Unwarranted Services
The manufacturer shall repair or replace unwarranted products, which have been returned to its factory, at its sole discretion under
the conditions below. The manufacturer shall accept no products for which no prior notice has been received.
The products, which the manufacturer deems repairable, will be repaired and returned. The manufacturer has prepared a price list
and those products, which can be repaired, shall be paid for every repaired appliance.
The closest equivalent product, available at the time, shall replace the products manufacturer deems unrepairable. The current market price shall be charged for every replaced product.
Installation and Programming Manual - СА62 Alarm Control Panel
3
Contents
SECTION 1: INSTALLATION
1. Introduction............................................................................................................................................................. 4
2. Installation.............................................................................................................................................................. 5
2.1 General Information.................................................................................................................................. 5
2.2 CA62 Installation Steps............................................................................................................................. 5
2.3 СА62 Alarm Control Panel Metal Box....................................................................................................... 6
2.4 CA62 Alarm Control Panel Plastic Box..................................................................................................... 7
2.5 CA62 Alarm Control Panel Inputs and Outputs......................................................................................... 8
2.6 Connecting of Detectors to CA62 Alarm Control Panel............................................................................. 9
2.7 Connecting of Peripheral Devices to СА62 Alarm Control Panel.............................................................. 11
2.7.1 Connecting LED and LCD Keyboards to CA62 Alarm Control Panel......................................... 11
2.7.2 Connecting of Proxi Reader PR62 to CA62 Alarm Control Panel............................................... 13
2.8 Using of PGM1, PGM2 and PGM3 Programmable Outputs..................................................................... 14
2.9 Using of SIREN Programmable Output..................................................................................................... 14
2.10 Connecting the CA62 Built-in Digital Communicator............................................................................... 15
2.11 Installing of VD60 voice dialer to CA62 Alarm Control Panel.................................................................. 15
2.12 Installing of AJAX LAN Module in CA62 Alarm Control Panel................................................................ 16
2.13 Connecting of UWE432 Universal Wireless Expander to CA62 Alarm Control Panel............................ 16
2.14 Powering up the CA62 Alarm Control Panel........................................................................................... 17
2.14.1 Technical Trouble Indication...................................................................................................... 17
SECTION 2: Programming
1. Programming the Software Parameters of СА62 Alarm Control Panel............................................................. 18
2. The symbols used in this manual......................................................................................................................... 18
3. Programming of CA62 via LED or LCD Keyboard............................................................................................... 18
4. Remote Programming of CA62............................................................................................................................. 19
5. Programming of Default Configurations in the CA62 Alarm Control Panel...................................................... 19
Menus for Programming the Software Parameters of CA62:
0. Engineer Parameters and Common Settings.............................................................................................. 20
1. User and Manager Codes Programming.................................................................................................... 26
2. Programming of Zones................................................................................................................................ 28
3. PGM and SIREN Outputs Programming..................................................................................................... 35
4. PARTITIONS Programming........................................................................................................................ 40
6. Programming of Communication Devices................................................................................................... 42
7. Programming of Peripheral Devices........................................................................................................... 47
SUPPLEMENTS
SUPPLEMENT А - Default Programming Tables (after RESET procedure):
TABLE 1 - Engineer Programming.................................................................................................................. 51
TABLE 2 - Manager Programming.................................................................................................................. 60
TABLE 3 - User Programming......................................................................................................................... 63
SUPPLEMENT B - Examples for Security Application with CA62......................................................................... 64
SUPPLEMENT C - Additional Information:
Coding recordings in log events...................................................................................................................... 67
Table of protocol Contact ID transmitted codes from CA62............................................................................ 69
Table of protocol SIA transmitted codes from CA62....................................................................................... 70
Hexadecimal table........................................................................................................................................... 71
Solving of Technical Problems During Powering up of CA62.......................................................................... 71
SUPPLEMENT D - Algorithms for Operation of ZONES with Key-Switch Type........................................................... 72
SUPPLEMENT E - Algorithm for Recording and Listening of Voice Messages........................................................... 74
SUPPLEMENT F - General Connection Diagram........................................................................................................ 75
4
Installation and Programming Manual - СА62 Alarm Control Panel
SECTION 1: INSTALLATION
1. Introduction
The СА62 alarm control system is an upgraded version of СА60plus and is designed for security and protection of residential and office buildings. The system is based on a modular principle.
The programming of CA62 can be done by two types of keyboards (LED or LCD) or remotely via ProSTE software.
The security control is managed by means of a keyboard or a proxi reader.
General specifications of СА62 alarm control panel:
Inputs: • 6 inputs for connecting detectors (5 inputs on the panel and 1 in the keyboard).
Zones: • From 6 to 12 zones with freely programmable parameters.
• Doubling the zone number in the panel by means of specific connection of the detectors.
• Individually settings for the balancing type of each input - one or two balancing resistors or zone doubling.
Partitions: • Two fully independent partitions in the system.
• Arming modes:
- Full (Arming of all zones in the system);
- Instant (Partial arming - the user is allowed to stay in some zones; the entry zone is secured and any intrusion will starts the alarm immediately;
- Stay (Partial arming - the user is allowed to stay in some zone; the entry zone is secured, an entry time
will start up in case of an intrusion).
• Security control by means of Proximity cards reader PR62.
• Auto Arming mode for arming the security areas in preprogrammed time.
Outputs: • 3 weak current and 1 power current programmable outputs type ОС (open collector).
• Same options for programming of all outputs.
Codes: • 4 or 6 digits access codes.
• 20 User codes, 4 Manager codes, 1 Engineer code.
• Programmable function “Ambush code” - generates a "silent" panic alarm, when the user is forced to
disarm the system.
• Supervised access of the Engineer to the programmed parameters in the system.
Events LOG: • Memory LOG for 256 events with time and date - can be viewed by a keyboard or via TTProgramming
Suite software.
Report to a • Built-in digital communicator for central station monitoring via telephone line. “Contact ID” and “SIA” standMonitoring ard protocols are supported.
Station: • Ajax - LAN (TCP/IP) communication module.
• VD60 - Voice dialer.
Peripheral • Up to 8 keyboards - LED and/or LCD models.
Devices: • Up to 4 proximity cards readers - PR62.
• Supported keyboards for CA62:
- LED61 - Keyboard with LED display up to 6 zones.
- LED62 - Keyboard with LED display up to 12 zones, supports operation with 2 Partitions (A and B).
- LED63 / VG - Keyboard with LED display up to 6 zones with option for voice messages.
- LED63 VG SE - Keyboard with LED display up to 12 zones, supports operation with 2 Partitions (A and B).
- LCD62 - Keyboard with icon LCD display up to 6 zones.
- LCD62В - Keyboard with icon LCD display up to 6 zones (blue backlight of the display).
- LCD63 - Keyboard with icon LCD display up to 6 zones with option for voice messages.
- LCD63SE - Keyboard with icon LCD display up to 12 zones with option for voice messages, supports
operation with 2 Partitions (A and B).
- LCD64 - Keyboard with icon LCD display up to 12 zones, supports operation with 2 Partitions (A and B).
• All keyboards have 1 built in zone and quick access buttons.
• Flexible programming of the buttons functions for arming and disarming the partitions in the system.
Programming: • The alarm panel parameters can be programmed from every keyboard (LED or LCD) in the system.
• Programming via PC with TTProgrammig Suite software (RS232 serial bus) or via telephone line.
• 4 default configurations of the system parameters, used for basic programming of 3 typical and 1 general
system configurations.
Technical • Transformer - 17 VAC, 17 VA.
Specifications: • Accumulator charger - 13.8 V, 1A, electronic overload protection.
• Back-up power supply - accumulator 12 V, 7,2 Ah.
• Current consumption - up to 100 mA for the control panel.
• Power supply for detectors - 13.8 V, 1A, electronic overload protection.
• Power supply for additional devices - 13.8 V, 1A, electronic overload protection.
• Operating temperature - from 0°C to +50°C.
• ABS Plastic box - dimensions: 315 х 260 х 80 mm.
• Weight - 2.42 kg.
Installation and Programming Manual - СА62 Alarm Control Panel
5
2. Installation
2.1 General Information
The CA62 Alarm control panel was designed and tested in compliance with electromagnetic compatibility standards.
The following recommendations need to be observed for the proper performance of the alarm station:
➢ Ensure the alarm system is properly earthed (grounded).
➢ Insulate the high and low voltage cables and use different input openings on the box.
➢ Avoid any loops of connecting wires within the very box and in their passage over or under the printed-
circuit boarding.
➢ Additional relays must not be placed in the CA62 Alarm control panel box as these may generate
electromagnetic interference when switched.
- Use only relays with good insulation between contacts and the winding.
- Relays, connected to outputs with an open commutator, must be designed to accommodate
a 12 V DC driving voltage and an impedance at the winding greater than 400Ω.
➢ The cable connecting the control panel and the keyboard is quadruple.
It is strongly recommended not to: use this cable to make other connections - connect to a telephone line, Flash-lamps control signals, sirens or relays.
➢ Avoid channels or cable forms that contain high voltage cables when placing the connecting cables. This is very important in cases where such cables are being used to power electric motors, fluorescent lamps or triple-phase voltage. Where the above is not possible, use only shielded cables, where the shield is grounded only in the alarm system box.
2.2 СА62 Installation Steps
We recommend during the installation of СА62 to follow the next installation steps:
➢ Carefully plan the security system - the type, number and location of detectors, the location of all peripheral devices, communication modules and the control panel, the type and length of connection wires and cables, etc.
➢ Mount all system elements - СА62 control panel, detectors, peripheral devices - keyboards and proximity card readers, indoor or outdoor sirens. During the mounting follow the described in item 2.6 connection
diagrams and choose the type of zone balancing - with 1, 2 or 3 resistors.
Attention: The numeration of the keyboards sequence is important, you have to follow strictly the order 1 to 8.
The different keyboard models supported by CA62 and their connection to the control panel are described in details in item 2.7.
➢ Power up the system as follow the steps in item 2.14. Check the normal system operation - there is
communication between the control panel and the keyboards, and the LED indication of the detectors in the
system is working.
➢ Program the default configuration type 0, 1, 2 or 3 - the most suitable for your alarm system installation. Details for default configurations are described in SECTION SUPPLEMENTS of this manual.
➢ Program all other necessary parameters concerning your alarm system installation, as follow the order:
peripheral devices, zones, partitions, programmable outputs (PGM), communicator, dialer, user and manager
access codes and attributes.
➢ Test the efficiency of your system installation.
6
Installation and Programming Manual - СА62 Alarm Control Panel
2.3 СА62 Alarm Control Panel Metal Box
Figure 1. Situation of СА62 alarm panel in metal box.
Figure 2. Side view and mounting of universal metal box.
Installation and Programming Manual - СА62 Alarm Control Panel
2.4 СА62 Alarm Control Panel Plastic Box
Figure 3. Opening the CA62 plastic box and template for wall mounting.
1 - Central support opening (behind PCB)
2 - Support openings
3 - CA62 Control panel
4 - Mains power supply terminal
5 - Main cable opening
6 - Additional cable openings
7 - Mains power supply opening
8 - Tamper button for box self-protection
Figure 4. Situation of СА62 control panel in plastic box.
7
8
Installation and Programming Manual - СА62 Alarm Control Panel
2.5 CA62 Alarm Control Panel Inputs and Outputs CA62
Figure 5. CA62 control panel inputs and outputs.
Terminals description of СА62 control panel:
• AC - Power supply from 17V / 17VA mains transformer
•  - “EARTH”
• AUX - Power supply -PGM for detectors with consumption up to 1А
• +PGM - Power supply for additional devices with consumption up to 1А
• PGM1, PGM2, PGM3 - Programmable outputs
• SIREN - Siren programmable outputs (PGM4 by default)
• Z2, Z3, Z4, Z5, Z6 - Zone inputs (Z1 zone is in the keyboard))
• COM - Common mass of the zones
• A, В - Terminals for telephone line connection
• А1, В1 - Terminals for
• RED, BLACK - Keyboard power supply
• GREEN, YELLOW - Interface between the panel and the keyboard
• F1 BATT - Battery fuse 0.75А, Resettable (PTC)
• F2 AUX - Fuse for powering sensors, programmable outputs and keyboards 0.5А, Resettable (PTC)
• F3 PGM - Additional device 0.5А mains fuse, Resettable (PTC)
• BATT - Battery cables for accumulator with parameters 12V / 7.2 Ah
• JPRG - Jumper for hardware RESET and default parameter recovery
• GPIO - Interface connector for programming
• EXPAND - Terminal for expander modules (Voice dialer)
Installation and Programming Manual - СА62 Alarm Control Panel
2.6 Connecting of Detectors to CA62 Alarm Control Panel
9
The security system is mounted with detectors with relay contacts.
Fire alarm detectors supplied with relay outputs can also be used.
There are three possible options for connecting of detectors to the CA62 zone inputs. The type of balancing for each
input is programmed separately at ADDRESSES 2zz6, where "zz" is the zone number - from 02 to 06.
The possible options for connecting the detectors and for balancing the zones are shown on Figure 6: a) Connecting
Detectors with One Balancing Resistor, b) Connecting Detectors with Two Balancing Resistors and c) Connecting Detectors with Three Balancing Resistors (zone doubling with connecting two groups of detectors/ zones to one input).
The zone doubling allows to the zones with numbers 2, 3, 4, 5 and 6 of СА62 control panel to be connected two groups
of detectors, as the first group is terminated with 1 kΩ resistor, and the second - with 2.2 kΩ. When a zone doubling
is realized in the system, the number of the zone for the second group of detectors, represents the number of related
zone + 6.
Use the supplied 1 kΩ resistors to balance the zones. The balancing resistors are installed on the last detector of the
circuit. The zones, which shall not be used, are terminated with one 1 kΩ resistor at the terminals of the CA62 Control
Panel, irrespective of the chosen type of zone balancing. A second way for temporary termination of the unused zones
is as program them as 0.Unused on the respective address - see the description of ADDRESS 2010.
After the initial power up of the control panel, the zone balance type has to be programmed. By default only 1 balancing
resistor is used.
The possible options for connecting detectors and balancing the zones are shown on Figure 7.
The hardware implementation of Zone 4 of the panel permits performance in pulse count mode, suitable for connecting
a rolling shutters detector. This mode counts short pulses - 2 to 4 ms for a period of 20 seconds. The first pulse starts a
20-second countdown during which pulses are expected to be received. Their number is assigned at Address 2047 of
the engineer program. An alarm signal is emitted when this number is reached within the time of 20 seconds. Otherwise
the pulse counter will be zeroed after the time of 20 seconds expires.
Activating the pulse count mode will automatically start when a number other than 0 is keyed in at Address 2047 of
the engineer program. The connection option of a rolling shutters detector to ZONE 4 is shown on Figure 7 d).
а) Connecting Detectors with
One Balancing Resistor
Connecting up to n detectors
Connecting up to 4 detectors
b) Connecting Detectors with Two Balancing Resistors
c) Connecting Detectors with Zone Doubling
d) Connecting of rolling shutters detector to Zone 4, in zone doubling mode.
Figure 6. Options for connecting detectors to the CA62 control panel.
10
Installation and Programming Manual - СА62 Alarm Control Panel
Key-switch
Must be normally closed.
Key-switch
Must be normally closed.
Tamper switch of the key-switch.
Tamper switch of the key-switch.
Connecting with one balancing resistor
Connecting with two balancing resistors
a) Connecting key-switch
The programmable output
must be programmed
as Fire Reset and the active
status must be +12 VDC.
Fire
detector
base
Connecting a fire detector with one balancing resistor
The programmable output
must be programmed
as Fire Reset and the active
status must be +12 VDC.
Fire
detector
base
Connecting a fire detector with two balancing resistors
b) Connecting a fire detector with a relay in the base
Fire
detector
base 2
Fire
detector
base 1
The programmable output
must be programmed
as Fire Reset and the active
status must be +12 VDC.
c) Connecting of two fire detectors to a doubling zone.
Figure 7. Connecting of key-switch and a fire detector to CA62 alarm control panel.
Installation and Programming Manual - СА62 Alarm Control Panel
11
2.7 Connecting of Peripheral Devices to СА62 Alarm Control Panel
2.7.1 Connecting LED and LCD Keyboards to CA62 Alarm Control Panel
Two types of keyboards can be used to control and program the СА62 alarm panel:
• LED keyboards -models LED61, LED62, LED63/ VG
• LCD keyboards - models LCD62, LCD62B, LCD63, LCD63SE, LCD64
LED61
LED62
LED63 VG SE
LED63VG
LCD63, LCD63SE
LCD62
LCD62B / LCD64
Figure 8. Basic view of LED and LCD keyboards.
Symbols to Figure 8:
. Status LED indication.
. Buttons for programming and controlling of CA62 control panel.
. Protective cover (open).
. Microphone.
. LCD display.
Attention: The LCD display is different for the listed keyboard models:
Models: LCD62, LCD62B, LCD63VG Model: LCD63SE, LCD64
For detailed description for indication and operation of all keyboard models refer to their individual manuals.
12
Installation and Programming Manual - СА62 Alarm Control Panel
All keyboard models are factory equipped with 4 terminals for connecting to СА62 control panel and two other terminals
for connecting to ZONE 1. Note: At LED61 keyboard, the input for ZONE 1 is equipped with two 10-cm long wires - black
and white for the bus connection. These terminals are marked with the respective colors.
The colors must be observed when connecting the keyboards to the СА62 Control Panel (see Figure 9). Note:
The connection in the connection below is principled. Note that in some keyboards the terminals for connecting to
ZONE 1 could be situated above the terminals for connecting to the control panel.
The zone cables are white and black in color. The zone in the keyboards HAS not to be balanced (except LED62
and LED63VG SE keyboards - the keyboard zone can be balanced with setting the ZONE EOL jumper, see the
jumpers explanation on Figure 10b). The zone in all model keyboards HAS NOT to be programmed as double
zone also. When more than one keyboard are connected to the control panel, each keyboard have to be assigned with
individual zone number - 1 or 7. Activating any keyboard zone shall be regard as an activation of ZONE 1 or ZONE 7,
according the individual programming.
No more than 8 keyboards (irrespective of their type) can be connected to one control panel. Each keyboard must be
assigned an individual address, by placing the jumper on the keyboard at its respective place (see Figure 10а). The
individual address ensures TAMPER event identification, whenever the TAMPER switch of the respective keyboard is
turned on.
The individual address of each keyboard is assigned with the help of a jumpers. Following the table (see Figure 10а)
the respective address could be programmed. The individual address of each keyboard in the system can be checked
at ADDRESS 7000 from the Engineer menu (see page 47).
The JT jumper must be placed where only one keyboard has been connected. Where more than one keyboards are
connected, the JT jumper should be placed on the most distant one. The JT jumper is set by default.
The cable connecting the LED60 and the LED61 Keyboards to the CA62 Control Panel must be no longer than 250m
and have a cross-section of no less than 0.25mm.
Keyboard:
CA62 control
panel terminals
(SE)
ZONE 1
DETECTORS WIRES
LCD64
Figure 9. Connecting keyboards to CA62 control panel.
Address
Jumper
1
2
3
4
5
6
7
Jumper location for
keyboard models:
LED61, LED63VG,
LCD62, LCD62B,
LCD63, LCD63SE,
LCD64
8
J0
J1
J2
Legend:
- The jumper is removed;
- The jumper is set
NOTE: The JT jumper must be set
in the most far unit in the bus.
Figure 10a. Table for keyboard address programming.
The LED keyboard zone is not balanced.
The jumper Zone EOL is removed.
The zone has two states:
• zone closed (the switch is closed)
• zone open (the switch is open)
1)
2)
3)
The LED keyboard zone is balanced.
The jumper Zone EOL is set.
The zone has three states:
• zone closed (the switch is closed) - item 1
• zone open (the switch is open) - item 1
• tamper - items 2 and 3
Jumper location
for keyboard
models:
LED62
LED63VG SE
NOTE: The JT jumper
must be set in the most
far unit in the bus.
Figure 10b. Jumper location and zone balancing of LED62 and LED63VG SE keyboards.
The parameters and the functions of the buttons for each keyboard can be programmed at ADDRESSES 70xx, according to the set with jumper address of the keyboard.
Installation and Programming Manual - СА62 Alarm Control Panel
13
2.7.2 Connecting of Proxi Reader PR62 to CA62 Alarm Control Panel
The PR62 proximity card reader was designed to control security in the systems integrated within the CA62 Control
Panel. The excellent card reading distance, the triple color indications, supplemented by the sound indicator, the integrated output, as well as the fine design, all make the PR62 any attractive supplement to the security system.
The PR62 can be connected to the terminals RED, GREEN, YELLOW and BLACK of the CA62 together with the
mounted keyboards. Up to four proximity readers can be included within one security system. Programming the various
addresses onto the readers will provide identification by the TAMPER of each of these. The Table for Address Programming is provided on Figure 11.
The proximity-card enables to arm and disarm the system, as well as to control the electric lock (key-switch) via integrated output. The internal structure, and the permissible output currents, are provided in Fig. 11.
It is possible that only proximity-card readers be included in a system without having an installed keyboard. In such
systems this would hinder current programming of parameters and cards, as well as Log Review and Technical Trouble
indications. Portable LED or LCD type keyboards can be used to accomplish such tasks.
Up to 24 cards can be assigned to one security system - one card for each of the 20 users and 4 cards for the Managers
in the system.
The Managers in the system are allowed to program the performance of the cards.
Arming and/or disarming rights must be assigned for the respective user code.
The user may not be designated a code combination. In such case the only means to control the security system would
be the proximity-card.
The parameters of the proximity card readers in the system can be programmed at ADDRESSES 71хх, according to the
set with jumper address of the proxi reader.
Internal structure of built-in PGM
PGMx terminal
* The JT jumper must be set in
the most far unit on the bus.
LED indication:
- green - the card is recognized or
required action is done,
- red - the card is not recognized or
required action is rejected,
- yellow (LED blinks) - ready.
Permissable currents:
- from +12 V - up to 10 mA
- towards GND - up to 100 mA
The output activates for 2
seconds after the recognised
card is drown back.
Two color LED indicator
Setting the address of PR62
Address
Jumper
1
2
3
4
Lock
J1
J2
Legend:
- The jumper is removed;
- The jumper is set
Mounting openings
Figure 11. PR62 Proximity card reader installation and connection diagram.
Signal cables
openings
14
Installation and Programming Manual - СА62 Alarm Control Panel
2.8 Using of PGM1, PGM2 and PGM3 Programmable Outputs
The СА62 Alarm panel PGM1, PGM2 and PGM3 outputs have a programmable active level. This allows them to be used
to transmit control signals towards external devices (e.g. a block siren input) or to directly control low-powered external
devices (e.g. relays, LED, etc.).
The internal structure of all PGMs is the same and is shown on Figure 12 a).
Figure 12 b) shows the connection of the relay and a light-emitting diode to the PGM. The active level of this connection
is low.
PGMx terminal
Permissible current:
- from +12 V - up to 10 mA
- towards GND - up to 100 mA
For SIREN output the
current supplied to GND
is up to 1 A.
Figure12. а) Internal structure of
programmable PGMx output
Figure12. b) Controlling light-emitting diode and
relay using PGM1 and PGM2 outputs
2.9 Using SIREN Programmable Output (PGM4)
The СА62 Alarm panel SIREN output has a programmable active level. With the default configuration the output is
with SIREN and POLARITY set attributes, which can be programmed at ADDRESS 3041. The output is activated in
case of alarm event in the system.
The internal structure is identical to the one shown in Figure 12 a) and we should point out that the transmitter can pass
through to GND electricity of up to 1 A.
Figure 7 shows how to connect SR110E, SR120 and SR200 sirens using the SIREN output.
The BLOCK jumper
in SR120 (BL in SR200)
must be set on.
a) Connecting SR110E using
a double-wire b) Connecting SR120/SR200
using a double-wire
The BLOCK jumper
in SR120 (BL in SR200)
must be removed.
c) Connecting SR120/SR200 using triple-wire.
Figure 13. 7 Controlling sirens using SIREN output.
Installation and Programming Manual - СА62 Alarm Control Panel
15
2.10 Connecting the CA62 Built-in Digital Communicator
The telephone line is connected to A and B terminals on
the CA62 Control Panel with no requirements to observe
polarity (Figure 14).
The telephone device is connected to A1 and B1 terminals on the CA62 Control Panel with no requirements to
observe polarity (Figure 14).
The parameters of the digital communicator are engineer
programmed.
It is not necessary to install additional components if the
built-in communicator is not to be used.
Telephone line
Telephone device
Figure 14. Connecting the CA62 builtin communicator
2.11 Installing of VD60 voice dialer to CA62 Alarm Control Panel
The “VD60” Voice Telephone Dialer module supplements the СА62 Alarm Control Panel, which serves to transmit alarm
event messages to the user, under the form of eight pre-recorded voice messages, of up to 5 sec. each. Two message
types are supported - by zone or by event (see description of ADDRESS 6035).
Turn off the power supply in order to connect the PCB of the voice telephone dialer to the EXPAND socket of the CA62
Control Panel (1). Fix the PCB onto the pre-mounted plastic spacers (2). The telephone line should be connected to
terminals A and B of the СА62 Control Panel. Polarity need not be observed.
The telephone device can be connected to terminals A1 and B1 of the СА62 Control Panel with no need of observing
polarity.
The voice dialer can simultaneously operate with the built-in digital communicator.
The dialer has one LED status indicator - PLAY/RECORD and BUSY, and one single digit LED display indicating the
number of the current message. Use the MSG key to switch-over between messages. Use the PLAY key to reproduce
messages when the REC jumper is turned off, or to record when it is turned on. A speaker (8-16 ohms) for listening to
recorded messages can be connected to the SP socket.
The voice dialer parameters can be programmed in the engineering menu at ADDRESSES 603х.
Figure 15. Installing the VD60 Voice Telephone Dialer.
16
Installation and Programming Manual - СА62 Alarm Control Panel
2.12 Installing of AJAX LAN Module in CA62 Alarm Control Panel
AJAX Module is an additional accessory for built-in installation in CA62 any other security or fire control system. It
transmits the system status to Monitoring centre or to the User via Internet. The AJAX module enables easy monitoring
and transmitting of alarm events occurring in the security system to existing Monitoring centre using standard monitoring software.
The AJAX Module can be programmed by means of special programming software TTProgramming Suite. For more
information please refer to the distributor of this equipment.
For the installation of AJAX LAN module in the CA62 universal plastic box
refer to sequence shown in Figure 16 as follow the steps:
 - Break off the pins from the plastic box.
 - Fix the mounting holes to the respective pins and carefully push down.
 - Fix the module to the plastic box with the screw from the spare parts kit.
Figure 16. Installing of AJAX LAN Module.
ATTENTION: The connecting between AJAX LAN module and
CA62 alarm control panel MUST BE done only with power
supply OFF and set RESET jumper on the AJAX module!
For the connection between AJAX LAN module and CA62 alarm control panel refer to
Figure 17, as follow the steps:
 - With Power supply OFF, connect the
AJAX module to the CA62 by means the
interface cable (Note: the interface cable is
not included in the spare parts kit for CA62.)
 - Connect LAN cable for Internet connection.
 - Place a reset jumper.
 - Turn the Power supply ON and wait
for 5 seconds in order to configure and to
obtain the default factory parameters.
 - Remove the RESET jumper.
Figure 17. Connecting of AJAX LAN module to CA62. 2.13 Connecting of UWE432 Universal Wireless Expander to CA62 Alarm Control Panel
UWE432 is a universal device for expanding existing wired alarm security systems. UWE432 communicates by means
of two-way radio connection with the AVA series wireless devices. The UWE432 supports up to 32 AVA series wireless
devices. ATTENTION: The connection between the CA62 control panel and UWE432 have to be with two balancing resistors!
Figure 18. Connecting UWE432 universal expander to CA62 alarm control panel.
NOTE: Out1 - Output for Low BATT and Lost Device state of wireless devices; Out2 - Output for TAMPER state of
wireless devices; In1 - Input for resetting wireless fire detectors (not less than 2 seconds); In2 - Input for wireless siren
control.
More information about UWE432 functions and programming you can find in its installation instructions.
Installation and Programming Manual - СА62 Alarm Control Panel
17
2.14 Powering up the CA62 Alarm Control Panel
The system should be powered-up only after it is installed and all necessary devices have been connected - control
panel, keyboard, detectors, etc.
Follow the next installation procedure when power-up the CA62 system for the first time:
➢ Set the JPRG jumper (Figure 5) on CA62 control panel, in order to configure the control panel default parameters (the factory settings).
ATTENTION: The CA62 alarm control pane supports 4 different default configurations. With every full hardware
system reset (jumper JPRG is set) the parameters for default configuration 0 will be set. The special of the
default configuration 0 is that all zones in the system are disabled (the 0.Unused type is set for all), the zone
balancing is with one resistor in the circuit and so on. For details for settings of the default system configuration 0, see SECTION 2 - Programming.
➢ Supply 220V mains power. The keyboard emits a short sound signal or series of short beeps according the used model. In case of a LED keyboard the light-emitting diodes on the display blink. When a LCD keyboard is used the display will light up in blue or orange.
➢ Remove the JPRG jumper. In normal operation mode - all detectors in the security system are inactive and there are no violated anti-TAMPER chains - the RDY LED lights up in green. The station now has been programmed with the default configuration 0.
If you operate with LCD keyboard the display is looking different according the model:
Models: LCD62, LCD62B, LCD63
Model:
LCD63SE
LCD64
➢ Use the red (+) and black (-) cables to connect the battery to the station.
All light-emitting diodes will blink and a sound signal will be heard where the keyboard is open or incorrectly connected.
Where there is an open zone or an open TAMPER for any zone, the LED for the respective zone (at LCD keyboards the
zone number is enclosed in brackets) together with the MEMORY or TAMPER LEDs on the display will light up (at LCD
keyboards lights up TRBL LED and symbol "wrench" is blinking).
ATTENTION! An open anti-sabotage chain (TAMPER) in the security system will sound the siren. To stop the
siren enter Manager code 0000. The respective zone LED remains permanently lit whereas the TAMPER LED will
blink. Remove the failure - the TAMPER LED remains permanently lit. Enter code 0000 again to clear the alarm
event from the memory.
2.14.1 Technical Trouble Indication
Any technical trouble in the panel will light up the Trouble indicator (blinking TRBL LED and/ or symbol “wrench” according of the keyboard model). To view these problems enter the 0000 manager code and single-press ENTER. The display
will indicate a list of current problems. The indications and their meaning are shown in the table below:
LED Keyboard
LED lighting up
LCD Keyboard
Digit enclosed in brackets
B
C
D
E
F
G
(1)
(2)
(3)
(4)
(5)
(6)
Technical trouble
(LED or symbol
is blinking)
No 220 V power supply
Battery low
Fuse burned
No telephone line
No communication available
Active TAMPER within the system
Trouble mode indication (Technical Trouble)
18
Installation and Programming Manual - СА62 Alarm Control Panel
SECTION 2: PROGRAMMING
Programming the Software Parameters of СА62 Alarm Control Panel
The system can operate with 4 or 6 digit codes. If a 6 digit code is set at ADDRESS 1001 at the end of every valid code
an extension "00" is automatically added. Next a new 6 digit code combination can be programmed.
The respective parameters can be configured from a LED or LCD keyboard or remotely by means of connected to the
system a personal computer via a telephone using the TTProgramming Suite Software.
Symbols used in this manual
For more clear presentation of the programming with the two types (LED and LCD) keyboards and for easy performance of the information in this manual, the following symbols for indicating of active (enabled) and inactive (disabled)
parameters in the engineering programming menus are used:
Indicator
ZONES
Parameter state
LED
LCD
Active (enabled parameter)
B - Lights on
(1) - Number enclosed in brackets
Inactive (disabled parameter)
 - Lights off
1 - Number without brackets
Keyboard programming
Entering the system engineer code will initiate the CA62 Alarm System programming mode for the engineer parameters. After restoring the default parameters (system RESET) the engineer code will remain 7777.
When you enter the engineer programming menu the indication of the used keyboards will be as follows:
- LED Keyboards - the LEDs RDY (green), ARM (red), TRBL (yellow) and BPS (red) are blinking together. At LED62
keyboard the symbols “lighting”, “wrench” and “sheet” are blinking together.
- LCD Keyboards - the LEDs RDY (green), ARM (red) and TRBL (yellow) are blinking together. The
symbol
blinks together with symbol . At LCD63SE keyboard the symbol
is blinking, and at the middle tower of the castle
the symbol
is steady.
starts blinking at the place of the
At LCD type keyboards, after entering engineer programming mode the symbol
clock. Every entered digit of the ADDRESS stop blinking and stays steady, the symbol next to it will be continue blinking, which means, that the system is waiting for entering the next digit of the 4 digit ADDRESS.
After entering 4 digit number of a valid ADDRESS a confirmation sound signal will be heard.
After entering of a 4 digit ADDRESS the engineer can program the respective system parameter. Use the provided in
this section tables with detailed descriptions of all available ADDRESSES in the system. You can use also the tables in
SUPPLEMENT A for quick reference. All entered parameters have to be confirmed with pressing the ENT button. When
reviewing the programmed parameters it is recommended to exit any given address by single pressing the CLEAR
button. This function will leave the introduced parameters unchanged. In case the programmer is disoriented in the engineer menu, it is recommended to exit the menu by double clicking the CLEAR button and to begin programming the
station parameters from the start.
ATTENTION: The CA62 Alarm System engineer parameters programming mode can be begin only when the
system is in disarmed mode! When there are several (up to 8) keyboards connected to the control panel in
the system you can program parameters only from this one where the engineer code has been entered. The
indication of all other keyboards will show that the system is in engineer programming mode, but you can not
program parameters with them.
How to read the information in the tables below:
Name of the programming menu
ADDRESS
Number
Description of the programming menu
ADDRESS 0001 - HARDWARE RESET ENABLE
Reset
Enable
Disables or enables the hardware RESET of the alarm station. Specialized service is
required where the hardware RESET is disabled and the engineer code is obscure.
The parameter status can be changed with pressing of random button of the keyboard.
Indication
NO
Programming
menu parameters
The hardware RESET is disabled.
LED

LCD
1 2 3 4 5 6
Indication
YES
The hardware RESET is enabled.
Default settings
LED

LCD
(1) (2) (3) (4) (5) (6)
- YES
Default configuration settings for that programming menu
Installation and Programming Manual - СА62 Alarm Control Panel
19
For easy finding the information in the programming tables, the ADDRESSES are organized in 7 separate sections:
 The first digit of the ADDRESS structure describes:
0 - Programming the engineer and common system parameters;
1 - Programming the access codes in the system;
2 - Programming the zone parameters in the system;
3 - Programming the PGM outputs in the system;
4 - Programming the partitions in the system;
6 - Programming the parameters of the communication devices in the system;
7 - Programming the parameters of the peripheral devices in the system.
 The second and the third digit in the ADDRESS structure logically separate the unit number for every section - for example 01, 02 and so on are zone numbers. The same principle is right for the sections for programming the parameters of access codes, zones, PGM outputs, partitions, communication and peripheral devices
in the system.
 The forth digit in the ADDRESS structure is the number of a parameter for a specific system resurse.
Example for ADDRESS structure reading:
Zone number
Section for zone
programming
Parameter for
programming the
zone type
Besides the information for activating and deactivating of the system parameters, for some menus are shown and concrete examples for the status and indication of the LCD keyboards.
Basic sequence in operation when programming the Engineer menu:
Remote programming of CA62
To access a ProSTE software program system requires an ID number and a station ID number. After restoring the default parameters these numbers will be the same and are 1234. In order to provide access to the system from the central
station enter the correct number of the central station at ADDRESS 6901 (PC ID).
A 24-hour period automatically begins after default parameters are restored during which the UDL communication with
the system is enabled even when the "ring number" parameter is zeroed at ADDRESS 6904 (with set 0 number, the
UDL communication will starts after receiving of 7 rings). After the initial 24-hour period, the UDL communication with the
system will enabled only if the "ring number" parameter set at ADDRESS 6904 is different from zero.
If during the 24-hour period the system is power off (together the main power supply and the battery), at the next power
on the started already 24-hour period will be disabled and the UDL communication will be enabled only if the "ring
number" parameter set at ADDRESS 6904 is different from zero.
If during the 24-hour period the engineer enters the ADDRESS 6903 and exit it by pressing the ENT button (with confirmation), then the 24-hour time period and this case will be disabled.
Detailed working instructions for the ProSTE software program are provided in the built-in Help files. The connection
between the local computer and the CA62 control panel is via a specialized module (the module is not included in the
CA62 equipment and is sold as a separate product.)
The details listed in this manual apply to all parameters for remote system programming.
Programming of Default Configurations in the CA62 Alarm Control Panel
The system supports 2 separate default configurations with set parameters. Enter a number of default configuration
(0-3) at ADDRESS 1000 in the engineer programming menu - see item 1. User and Manager Codes Programming. At
SUPPLEMENT B are shown examples for using the default configurations in the system.
ATTENTION: With realizing full hardware reset, in the system automatically will be set the
default configuration 0 parameters!
The default configuration 0 parameters are described in details in Table 1 (SUPPLEMENT
A) and they are described in ADDRESSES tables below.
20
Installation and Programming Manual - СА62 Alarm Control Panel
0. Engineer Parameters and Common Settings
ADDRESS 0000 - CHANGING THE ENGINEER CODE
A new access code to the alarm station engineer parameters can be assigned at this address.
Note: If the 6-digit long access code is set, the combination "00" automatically will be added at the end
of all valid codes in the system.
Indication
Engineer
code
LED

LCD
1 2 (3) (4) (5) (6)
The light-emitting diodes 3, 4, 5 and 6 on the keypad display light up. These go out one by one as the
new code is entered. The new code has to be entered a second time.
Default settings
- 7777
ADDRESS 0001 - HARDWARE RESET ENABLE
Reset
Enable
Disables or enables the hardware RESET of the alarm station. Specialized service is required where
the hardware RESET is disabled and the engineer code is obscure.
The parameter status can be changed with pressing of random button of the keyboard.
Indication
NO
The hardware RESET is disabled.
LED
LCD
1 2 3 4 5 6

Indication
YES
The hardware RESET is enabled.
Default configuration
LED

LCD
(1) (2) (3) (4) (5) (6)
- YES
ADDRESS 0002 - RESTORING DEFAULT PARAMETERS (SOFTWARE RESET)
Default
settings
Restoration of default settings of the station. The buttons 1, 2, 3, 4, 5, 6 are pressed in succession and
confirmed with the ENTER button.
ADDRESS 0003 - RESTORING DEFAULT MANAGER CODE (PARTIAL SOFTWARE RESET)
Restoration of the default manager code. Buttons 1, 2, 3, 4, 5, 6 are pressed in succession and conPartial reset firmed with the ENTER button.
The station restores the default 0000 manager user code.
ADDRESS 0010 - AUTHORITY TO ARM USING A ONE PUSH-BUTTON (QUICK ARM)
Quick ARM
Enable
A quick Arming mode using one button, without need to enter a valid user code is assigned at this address. The assigning can be done for PARTITION A, PARTITION B or for both partitions.
The parameter is activated with pressing a digit number coresponding to the partition number - 1 for
PARTITION A and 2 for PARTITION B. Next pressing of the button will deactivate the parameter.
PARTITION
A
Quick Arming of PARTITION A without legal user
code.
PARTITION
B
Quick Arming of PARTITION B without legal user
code.
Default configuration
- PARTITION A, PARTITION B
Indication
LED

LCD
(1) 2 3 4 5 6
Indication
LED

LCD
1 (2) 3 4 5 6
Installation and Programming Manual - СА62 Alarm Control Panel
21
ADDRESS 0011 - AUTHORITY CODE DURING AMBUSH (AMBUSH CODE)
Ambush
Code
Enabling/ Disabling the ambush code in the system. The parameter status can be changed with pressing of random button of the keyboard.
Indication
NO
Disabled ambush code.
YES
Enabled ambush code. The code is made up by adding 1 to a legal user code. There is no carrying over for
codes ending in the figure 9.
For example, the ambush code for 1234 is 1235, and
for 9999 it is 9990.
Default settings
LED
LCD
1 2 3 4 5 6

Indication
LED

LCD
(1) (2) (3) (4) (5) (6)
- NO
ADDRESS 0012 - ENABLED KEYBOARD BLOCKING IN CASE OF ACCESS CODE ERROR
Enable
keypad
block
Enabling/ Disabling blocking the keyboards buttons in case of access code error. The parameter status
can be changed with pressing of random button of the keyboard.
NO
Disables keyboard blocking in case of access code
mistake.
YES
Enables keyboard blocking for 30 sec. following the
triple introduction in sequence of a false code - for 30
seconds the keyboard buttons are disabled, and a continuous sound signal is heard.
Default settings
Indication
LED

LCD
1 2 3 4 5 6
Indication
LED

LCD
(1) (2) (3) (4) (5) (6)
- NO
ADDRESS 0013 - TECHNICAL TROUBLE INDICATION MASK
Trouble
mask
The mask for sound indication (two short beeps in every 20 seconds) from the keyboard in Technical
Trouble mode is assigned at this address.
The trouble indication mask is enabling with pressing a button with the respective number from 1 to
6 - see item 2.14.1 for the trouble indication in the system. Pressing the button with the same number
again will disable the trouble indication mask for the respective technical problem.
Only those LEDs whose numbers correspond to technical problems for which sound indications are
available will light up on the display at the end of the procedure. The set parameters are confirmed with
pressing the ENT button.
The procedure for enabling/ disabling the trouble mask indication are the same for all types and models
CA62 keyboards.
Example for disabling a trouble indication mask using LCD62 keyboard:
1. АС Loss
Loss of 220 V mains supply.
2. ВАТТ
Low
Drop in battery charge, no battery or burnt out F1 battery fuse.
3. Blown
Fuse
Burnt out PGM fuse.
4. No Tel.
line
Loss of telephone line.
5. СОММ
Error
Central station communication failure.
6. TAMPER
Activated TAMPER within the system.
Default settings
- AC Loss, ВАТТ Low, Blown Fuse, No Tel. Line, СОММ Error, TAMPER
22
Installation and Programming Manual - СА62 Alarm Control Panel
ADDRESS 0014 - 220 V AC POWER SUPPLY FAILURE INDICATION DELAY
AC delay 30
minutes
Setting of 30 minutes delay for 220V AC power supply failure indication. The parameter status can be
changed with pressing of random button of the keyboard.
NO
Disables 30 minutes indication delay for 220 V power
supply failure in keyboards and message transmission
via digital communicator.
YES
Enables 30 minutes delay indication for 220 V power
supply failure in keyboards and message transmission
via digital communicator.
Default settings
Indication
LED

LCD
1 2 3 4 5 6
Indication
LED

LCD
(1) (2) (3) (4) (5) (6)
- NO
ADDRESS 0015 - TELEPHONE LINE FAILURE INDICATION DELAY
Line fault
delay
A delay of 0 to 99 minutes is set prior to indication of a telephone line failure (ММ). The indication has
a hexadecimal expression - see SUPPLEMENT С.
Two digits are entered. When a period is less than 10 minutes the first digit introduced must be 0. If no
indication of a dead telephone line is needed, 00 is entered.
Default settings
- 00
ADDRESS 0016 - Bell on TelEPHONE Line Fault in ARM MODE
Bell on Tel.
Line Fault
Enabling/ Disabling of sound signalization for telephone line fault, when the system is in ARM mode SIREN output is activated for the bell time of the sirens. It is possible the signalization to be activated
separately only for PARTITION A, only for PARTITION B, or for both of them for the same time.
The parameter status can be changed with pressing of random button of the keyboard.
NO
The sound signalization for telephone line fault in ARM
mode is disabled.
YES
The sound signalization for telephone line fault in ARM
mode is enabled. In case of telephone line fault in Partition A, Partition B, or in both of them the sound signalization is on if the system is in ARM mode.
In the example the Bell on Tel.Line Fault parameter
is enabled for both Partitions A and B.
Default settings
Indication
LED

LCD
1 2 3 4 5 6
Indication
LED

LCD
(1) (2) 3 4 5 6
- NO
ADDRESS 0017 - TAMPER ALARM SIGNAL
TAMPER
Alarm
signal
A sound alarm signal is enabled or disabled at this address for a TAMPER event when the system is
not armed. Programming this address will not affect the TAMPER signal when the system is in armed
mode. Programming this address will affect the performance of the programmable SIREN output.
Every pressing of a digital button alternatively changes the enabled / disabled status. The display
indication is shown in the table.
ENABLED
(sound)
Enabled sound alarm signal (keyboard buzzer and
sirens) for TAMPER event, when the system is not
armed.
DISABLED
(silent
Disabled sound alarm signal (keyboard buzzer only)
for TAMPER event, when the system is not armed.
A TAMPER event is indicated by an interrupted sound
signal emitted by the system keyboard.
Default settings
- ENABLED
Indication
LED

LCD
(1) (2) (3) (4) (5) (6)
Indication
LED

LCD
1 2 3 4 5 6
Installation and Programming Manual - СА62 Alarm Control Panel
23
ADDRESS 0020 - Test for proper zone operation (Walk test)
Walk Test
Enables functional test of zones. The respective light-emitting diode (LED keyboard) or a number of a
zone (LCD keyboard), blinks while the zone is activated (open) in this mode. During the test every zone
activation is accompanied with "Chime" sound signal and with continuous sound for "reject" - open
TAMPER zone. As long as there is an open tamper zone its respective number remains active - permanently lit LED (LED keyboard) or enclosed in brackets (LCD keyboard).
ADDRESS 0021 - KEYBOARD TEST
Keyboard
test
Checks the serviceability of the keypad light-emitting diodes and buzzer.
ADDRESS 0022 - PGM1, PGM2, PGM3 and SIREN (PGM4) PANEL PROGRAMMABLE OUTPUT TEST
Output test:
1 PGM1
2 PGM2
3 PGM3
4 SIREN
(PGM 4)
Serviceability tests of programmable outputs is carried
Индикация
out by pressing a numbered button which corresponds
LED
LCD
to the programmable output.
(1)
(2)
3 (4) 5 6

The respective number on the LED or LCD display is
activated and the output passes into a low level - 0V. Example: To the outputs PGM1, PGM2 and
Pressing the button with the corresponding number a SIREN is set a low level - 0V. To the output
second time renders the output into a high level - 12V. PGM3 is set a high level - 12V.
ADDRESS 0023 - DISPLAY COMMUNICATOR
Displa communicator
The performance of the communicator can be directly monitored at this address.
Note: Before starting the monitoring of the communicator performance you have to enter a telephone
number at ADDRESS 6010.
The ARM button causes test transmission from the communicator to the central station and from the
voice dialer to assigned telephone numbers. The 0 button aborts any running communication and deletes the queue of events to be sent.
The meaning of the symbols is given below, as the "active state" means permanent lighting of the
LEDs (LED keyboard) or enclosed in brackets number (LCD keyboard).
After communication has been successfully completed the keyboard emits a sound signal. The CLEAR
button exits Address 0023.
1: Dial Tone
• LED blinks / ( ) at LCD - searching for a “dial” free tel. line
• active state / or (1)/ - a “dial” signal has been identified
2: Dialling
• LED blinks / ( ) at LCD - dialing the telephone number
• active state / or (2)/ - telephone number has been dialed
3: Wait HS
(handshake)
• LED blinks / ( ) at LCD - expecting a HAND SHAKE from central station
• active state / or (3)/ - the necessary handshake signal has been identified
4: Send data
• LED blinks / ( ) at LCD - transmitting data to central station
• active state / or (4)/ - the current data has been transmitted
5: Wait
"kiss-off"
• LED blinks / ( ) at LCD - expecting confirmation from central station
• active state / or (5)/ - transmitted data has been successfully received
6: All sent
• active state / or (6)/ - communication process has been completed and all data has been successfully transmitted to the central station
24
Installation and Programming Manual - СА62 Alarm Control Panel
ADDRESS 0024 - DISPLAY LOG EVENTS
Display
LOG
The events recorded in the power independent memory of the station can be traced with the help of
the arrows. The first event which is visualized is the last recorded.
Viewing the LOG with a LED keyboard
The indication has a hexadecimal expression - see SUPPLEMENT С.
Viewing the LOG with a LCD keyboard
Use the 1,2 and 3 buttons to view, as follows:
- Button 1 - Displays information for the event time;
- Button 2 - Displays information for the event time;
- Button 3 - Displays information for the LOG code. See SUPPLEMENT C for detailed description of
Coding recordings in log events.
ADDRESS 0025 - DISPLAY UDL PROCESS
UDL/
Direct UDL
The Up / Down Load process can be directly monitored at this address.
A single click on the 0 button aborts current communication.
A single click on the AND button can start manual communication. This will ignore the counter for
incoming calls and will directly proceed on to step 2.
The meaning of the symbols is given below, as the "active state" means permanent lighting of the
LEDs (LED keyboard) or enclosed in brackets number (LCD keyboard).
The CLEAR button exits Address 0025.
1: Ring
• LED blinks / ( ) at LCD - each blink indicates one received call
• active state / or (1)/ - the number of designated at ADDRESS 6904 calls have been received
2: Call back
• LED blinks / ( ) at LCD - a CALL BACK process
• active state / or (2)/ - CALL BACK completed
3: Currier
• LED blinks / ( ) at LCD - process of detecting a carrier
• active state / or (3)/ - established connection to PC
4: Receive
• LED blinks / ( ) at LCD - receiving data from central station
• active state / or (4)/ - data pack received
5: Transmit
• LED blinks / ( ) at LCD - transmitting data to central station
• active state / or (5)/ - data pack transmitted
6: End
• active state / or (6)/ - up / down loading completed
ADDRESS 0026 - DIGITAL COMMUNICATOR HARDWARE TEST
Comm. HW
test
A step by step test of the hardware of the digital communicator can be done at this address. A lightemitting diode on the keypad lights up to visualize every step. There is no time limitation for the
steps.
!During the test the digital communicator is blocked and disabled!
The first step of the digital communicator hardware test automatically begins after Address 0026 is
entered. Transition between the various steps can be accomplished with the respective digital buttons
1 to 5 or with the help of the arrows. The light-emitting diodes or enclosed in brackets number, indicate
the number of the current step:
1: Relay
The built-in relay is activated at this step. As a result the telephone line, connected to terminals A and
B, is discontinued from terminals A1 and B1, where the local telephone device or some other apparatus using the telephone line, should be connected. During this step the telephone line voltage should
be measured at terminals A and B (to read usually between 40 and 60 V DC) and at terminals A1 and
B1 (to read 0 V DC).
2: Dial tone
The digital communicator has engaged the telephone line here. The voltage measured at terminals A
and B should read between 7.5 V DC and 10.5 V DC. At the same time the built-in Dial Tone Detector
is also activated - a detector for the DIAL signal.
Every time when the communicator identifies a dial tone signal, a beep sound from the keyboard will
be heard.
3: Low freq.
The digital communicator attributes low frequency to the telephone line.
4: High freq. The digital communicator attributes high frequency to the telephone line.
5: DTMF
The digital communicator attributes a DTMF signal.
Installation and Programming Manual - СА62 Alarm Control Panel
25
ADDRESS 0030 - SETTING THE BUILT-IN CLOCK
Setting the
clock
The hours and minutes are set (HH:MM).
At LED keyboards the indication is hexadecimal and the digits are displayed one by one. To view the
clock, the digits can be browsed with the help of the arrows.
At LCD keyboards you can enter the hour and minutes directly from the keypad buttons, while the
position of the entered digit blinks.
Default settings - 00:00 h
ADDRESS 0031 - SETTING THE DATE
Setting the
date
The date and month are set (DD.MM).
At LED keyboards the indication is hexadecimal and the digits are displayed one by one. To view the
date, the digits can be browsed with the help of the arrows.
At LCD keyboards you can enter the date and month directly from the keypad buttons, while the position of the entered digit blinks.
Default settings - 01:01
ADDRESS 0040 - CHIME ENABLE/DISABLE
Chime
Enable/
Disable
At this address the engineer can enable or disable the sound signallization (Chime) for opennig of
an entry-exit type zone. The parameter status can be changed with pressing of random button of the
keyboard.
Indication
YES
The Chime is Enabled.
LED

LCD
(1) (2) (3) (4) (5) (6)
Indication
NO
The Chime is Disabled
Default settings - NO
LED

LCD
1 2 3 4 5 6
26
Installation and Programming Manual - СА62 Alarm Control Panel
1. User and Manager Codes Programming
ADDRESS 1000 - DEFAULT CONFIGURATION SETTING
Setting
CA62 Alarm control panel supports 4 default parameter configurations.
of default
Enter a number from 0 to 3 of a default configuratin.
configuration All the menus in this manual are described for the DEFAULT CONFIGURATION 0.
Default settings - 0
ADDRESS 1001 - Programming the code digits
Number of
the code
digits
The system allows using 4 and 6 digits codes.
4 digits
The system Engineer, managers and users are using 4
digit access codes.
6 digits
The system Engineer, managers and users are using 6
digit access codes.
Default settings
Indication
LED
LCD
1 2 3 4 5 6

Indication
LED

LCD
(1) (2) (3) (4) (5) (6)
- 4 digits
ADDRESS 1010 - USER CODE 1 ATTRIBUTES
User Code 1
USER CODE 1 attributes are assigned at this address.
The user code can have more than one attribute. Pressing a digital button with the respective number
activates the given attribute. The selected attribute is indicated with active number of the pressed digit.
Pressing the same digit again will inactivate the attribute
Only those numbers, which correspond to the assigned attributes, will remain active at the end of the
procedure. Pressing the ENTER button confirms the programmed attributes.
Indication at Default settings
LED

LCD
(1) (2) (3) (4) (5) (6)
1. DISARM
Disarming the system
Authorizes this user code to Disarm the site.
2. STAY ARM
Arming mode at which the user can stay in certain areas
Authorizes this user code to arm those zones that have not been assigned a STAY attribute.
3. BYPASS
Zone Bypassing
Authorizes this user code to bypass zones in armed site.
4. PROGRAM
Programming
Authorizes this user code to program system parameters.
5. PART A
Partition А
Authorizes this user code to operate with Partition A in the security area (bypass, arm, disarm, etc).
6. PART B
Partition В
Authorizes this user code to operate with Partition A in the security area (bypass, arm, disarm, etc).
Default settings
- DISARM, STAY ARM, BYPASS, PROGRAM, PART А; No code*.
* Note: User codes in the system can be programmed only from the Manager Programming Menu.
Installation and Programming Manual - СА62 Alarm Control Panel
27
All the ADDRESS for User code attributes from 2 to 20 are programmed in the same way as ADDRESS 1010:
- ADDRESS 1020 - USER CODE 2 ATTRIBUTES
- ADDRESS 1030 - USER CODE 3 ATTRIBUTES
...
- ADDRESS 1090 - USER CODE 9 ATTRIBUTES
- ADDRESS 1100 - USER CODE 10 ATTRIBUTES
...
- ADDRESS 1190 - USER CODE 19 ATTRIBUTES
- ADDRESS 1200 - USER CODE 20 ATTRIBUTES
At ADDRESSES for User code attributes from 2 to 20 no code combination has been introduced, and the default settings for all of them are: DISARM, STAY ARM, BYPASS, PROGRAM, PART A.
ADDRESS 1210 - CHIEF MANAGER CODE ATTRIBUTES
Chief
Manager
MANAGER CODE attributes are assigned at this address.
The manager code can have two attributes. Pressing a digital button with the respective number activates the given attribute. The selected attribute is indicated with active number of the pressed digit.
Pressing the same digit again will inactivate the attribute
Only those numbers, which correspond to the assigned attributes, will remain active at the end of the
procedure. Pressing the ENTER button confirms the programmed attributes.
Indication at Default settings
LED

LCD
1 2 3 4 (5) (6)
5. PART A
Partition А
Authorizes the Manager code to operate with Partition A in the security area (bypass, arm, disarm,
etc).
6. PART B
Partition В
Authorizes the Manager code to operate with Partition B in the security area (bypass, arm, disarm,
etc).
Default settings
- PART A, PART B; Access code 0000
ADDRESS 1220 - MANAGER 1 CODE ATTRIBUTES
Manager 1
MANAGER 1 CODE attributes are assigned at this address.
The programming is the same as for ADDRESS 1210.
No code combination has been introduced.
ADDRESS 1230 - MANAGER 2 CODE ATTRIBUTES
Manager 2
MANAGER 2 CODE attributes are assigned at this address.
The programming is the same as for ADDRESS 1210.
No code combination has been introduced.
ADDRESS 1240 - MANAGER 3 CODE ATTRIBUTES
Manager 3
MANAGER 3 CODE attributes are assigned at this address.
The programming is the same as for ADDRESS 1210.
No code combination has been introduced.
28
Installation and Programming Manual - СА62 Alarm Control Panel
2. Programming of Zones
The zone parameters in the system are programmed at ADDRESSES 2xxx. The parameters for every zone are programmed separately, as every zone has to be attached to one or the both partitions in the system.
ADDRESS 2000 - NUMBER OF ACTIVATIONS PER ZONE FOR AUTO BYPASS MODE
The number of activations (number of alarm cycles from 0 to 9) in one arm mode, which have to be
AutoBypass accomplished for a zone with an assigned AUTO/BPS parameter, are entered at this address. After
Counter
reaching the indicated number of activations, the respective zone will be automatically bypassed.
When disarmed and then again armed the respective zone will remain armed.
Default settings - 6
ADDRESS 2001 - ENABLING FOR INSTANT TYPE ZONES
Enable
Instant
Intrusion in any Instant type zone during exit time is enabled or disabled at this address. Enabling this
operating mode would reduce the probability for a false alarm signal to be triggered off by mistake on
behalf of the user.
The parameter status can be changed with pressing of random button of the keyboard.
NO
Disabled intrusion in INSTANT type zones during exit
type.
YES
Enables intrusion in INSTANT type zones during exit
type.
Default settings
Indication
LED

LCD
1 2 3 4 5 6
Indication
LED

LCD
(1) (2) (3) (4) (5) (6)
- NO
ADDRESS 2010 - ZONE 1 TYPE
The zone type is set at this address. Only one type can be selected for a given zone. Press the
digital button, which corresponds to the number of the desired type. At LED keyboards the indication
is hexadecimal and is shown in the table in SUPPLEMENT С.
At LCD keyboards the information for the zone type is visualized on the display in two ways - with
hexadecimal number and as a natural number on the place of the last digit of the clock.
Example for programming of the Zone 1 as 1. Entry/Exit type using LCD62 keyboard:
ZONE 1
Type
The Zone types are as follows:
Indication
LED
0. Unused

The zone is not being used.
LCD
1 2 3 4 5 6
Entry- Exit zone.
Provides time to arm and disarm the site. After arming, the detector, which
was triggered off in this zone, will not sound an alarm until the programmed
EXIT TIME expires.
1. Entry/Exit
No violation of the zone when in armed mode will sound an alarm before the
programmed ENTRY TIME expires.
A sound signal is activated from the keyboard buzzer during entry and exit
time.
Indication
LED

LCD
1 2 3 4 5 (6)
ADDRESS 2010 description continues on page 29 
Installation and Programming Manual - СА62 Alarm Control Panel
2. Follow
3. Instant
4. Fire
5. Panic
6. Tamper
7. Medical
8. KeySwitch
Follow zone
An alarm zone which is active only when the site is armed. The zone operates
instantaneously and activates the programmable ALARM and SIREN type
outputs, and the communicator.
Activating the zone during entry or exit time does not cause an alarm event.
When the system is disarmed, the activation of a zone is indicated by blinking of the respective light-emitting diode for the zone (LED keyboards) or
enclosed in brackets zone number (LCD keyboards) for the time that the zone
remains open.
Follow zone
An alarm zone which is active only when the site is armed. The zone operates
instantaneously and activates the programmable ALARM and SIREN type
outputs, and the communicator.
Activating the zone during entry or exit time does not cause an alarm event.
When the system is disarmed, the activation of the zone is indicated with active zone number for the time that the zone remains open.
An INSTANT type zone can be violated while Exit time is running if at ADDRESS 2001 the "Enabled Instant" parameter is enabled.
24-hour fire zone
Allows connecting 12 V fire detectors to the system.
These should avail of a normally closed relay output in inactive status.
Any activation of the zone will trigger off SIREN type outputs, the programmable FIRE type outputs and the station communicator.
24-hour panic type zone
Silent panic (2.Silent attribute is set on ADDRESS 2хх2, where хх is the
zone number) - only the programmable PANIC type outputs and the station
communicator can be activated. The respective LED (zone number at LCD
keyboard) blinks while the zone is active. There is no memory indication. After
a legal user code is entered, the MEMORY LED and the activated zone LED
(zone number at LCD keyboard) both light up continuously.
Sound panic - the SIREN output, the programmable PANIC type outputs
and the station communicator are activated. The sirens are instantaneously
activated irrespective of the programmed time delay. Activating the zone will
cause the MEMORY LED and the activated zone LED (zone number at LCD
keyboard) to light up continuously.
The indication of the memory can be deleted by entering a legal user code, a
manager code or during the next arming.
24-hour tamper type zone
Activating this zone type triggers off the SIREN output, the programmable
TAMPER type outputs and the station communicator. Any activation of the
zone would trigger off a sound signal from the keyboard buzzer when the
system is disarmed and the TAMPER siren output has been programmed as
SILENT at ADDRESS 0017.
The indication of the memory can be deleted by entering a legal user code or
manager code or during the next arming.
24-hour medical type zone
Assigning this zone type will set the programmable MEDICAL type outputs
active and will start the communicator. The activated zone LED (zone number
at LCD keyboard) will light up irrespective of the system status. The indication
of the memory can be deleted by entering a legal user code, manager code
or during the next arming.
Key-Switch, 24-hour burglary type zone.
When this zone type is assigned, the respective panel input is used to transmit the arming and disarming signal with the help of a keyswitch.
The installer has to set the type of the zone activation:
• With an impulse (PULSE attribute is set at ADDRESS 2013);
• Reaction of open or in normal operation mode zone (LATCH attribute is set
at ADDRESS 2013).
Arming is only possible in Full Arm mode. Arming will be anticipated only when
the system is ready - all zones are inactive.
Indication
LED

LCD
1 2 3 4 (5) 6
Indication
LED

LCD
1 2 3 4 (5) (6)
Indication
LED

LCD
1 2 3 (4) 5 6
Indication
LED

LCD
1 2 3 (4) 5 (6)
Indication
LED

LCD
1 2 3 (4) (5) 6
Indication
LED

LCD
1 2 3 (4) (5) (6)
Indication
LED

LCD
1 2 (3) 4 5 6
ADDRESS 2010 description continues on page 30 
29
30
Installation and Programming Manual - СА62 Alarm Control Panel
9. Auxiliary
24-hour auxiliary type zone
When this zone type is assigned, respectively a number of AUX attribute
should be programmed at ADDRESS 2xx4, where xx is the number of the
zone.
Default settings
Indication
LED

LCD
1 2 (3) 4 5 (6)
- 0.Unused type
ADDRESS 2011 - ZONE 1 ATTRIBUTES 1
Zone 1
Attributes 1
Parameters "ATTRIBUTES 1" for ZONE 1 are programmed at this address.
More than one attribute can be assigned for the zone. Pressing a digital button with the respective
number will activate a given attribute. Every activated attribute number is indicated as a lighting on
LED or enclosed in brackets number. Pressing the same digital button again will deactivate the attribute. At the end of this procedure, the LEDs or zone numbers, which correspond to the assigned
attributes only, will remain activated.
Indication at Default settings
LED

LCD
(1) (2) 3 4 5 6
The parameters “ATTRIBUTES 1” are as follows:
1. Auto
Bypass
Attention:
This attribute is not
Authorization for automatic Bypassing the zone after reaching the number of
valid for zone types:
activations per armed mode as set in address 2000.
Fire, Panic, Medical
and Key-Switch.
2. Bypass
Attention:
Authorization to Bypass a zone. Assigning this attribute to the respective zone This attribute is valid
will authorize bypass of the zone on behalf of the system user or manager.
for all zone types, except for Key-Switch.
3. Stay
Attention:
This attribute is not
The zone is not going to be armed in the STAY mode. Assigning this attribute valid for zone types:
to the respective zone will authorize the respective Stay mode zone arming. Fire, Panic, Tamper,
Medical, Key-Switch
and Auxiliary.
4. Force
Attention:
If when arming the system the zone is open (activated), then the respective This attribute is not
Partition will be armed, and the respective zone will be armed after it is re- valid for zone types:
stored.
Entry/Exit, Follow
and Key-Switch.
5. Double
DOUBLE KNOCK type zone. Assigning this attribute to the respective zone
authorizes Double Knock mode performance in the zone.
A 3-minute time interval starts when a detector in the zone is activated for the
first time in armed mode. An alarm event is registered if a second detector
activation is recorded within this interval in the same or another zone.
An alarm event will also be registered if no zone is restored within 15 seconds
of the first activation of the zone sensor.
Attention:
This attribute is not
valid for zone types:
Fire, Panic, Medical
and Auxiliary.
6. E/E Final
When armed the zone will perform as Entry/Exit type.
The system will be armed:
А) When the exit time is over;
B) immediacy after closing the entry-exit zone.
Attention:
This attribute is valid
for zone type Entry/
Exit only.
Default settings
- AutoBypass, Bypass attributes
Installation and Programming Manual - СА62 Alarm Control Panel
31
ADDRESS 2012 - ZONE 1 ATTRIBUTES 2
Zone 1
Attributes 2
Parameters "ATTRIBUTES 2" for ZONE 1 are programmed at this address.
More than one attribute can be assigned for the zone. Pressing a digital button with the respective
number will activate a given attribute. Every activated attribute number is indicated as a lighting on
LED or enclosed in brackets number. Pressing the same digital button again will deactivate the attribute. At the end of this procedure, the LEDs or zone numbers, which correspond to the assigned
attributes only, will remain activated.
The parameters “ATTRIBUTES 2” are as follows:
The siren will be activated when the set Bell Delay time is over.
1. Bell Delay The Bell Delay time can be programmed at ADDRESS 4013 (for Partition A) and at ADDRESS 4023
(for Partition B).
2. Silent
In arming mode, the siren will not be activated if the Silent (silent panic) attribute is assigned.
The programmable PANIC type outputs and the system communicator will be activated only. A violation of a zone is indicated with a flashing LED or enclosed in brackets zone number while the zone is
active.
3. Video On
Armed
Videorecording of alarm events
In case of alarm event the VIDEO ON ARMED outputs will be activated for 1 minute.
4. Write to
LOG
Write to LOG file
Every zone activation and restoring, irrespective of the system arming status, will be recorded (by
means of special codes) in the memory LOG file, as this causes no influence on the whole functionality of the system, i.e. if there is an arming command - the system will be armed, if there is disarming
command - the system will be disarmed. The same rule is valid and for sending a system reports to a
monitoring station.
5. Chime
“CHIME” Mode
In disarmed mode and assigned "Chime" attribute, with every activation of a zone the keyboards will
produce a specific sound signal.
Default settings
- no attribute is set
ADDRESS 2013 - ZONE 1 ATTRIBUTES 3
Zone 1
Attributes 3
At this address are assigned only parameters "ATTRIBUTES 3" for Key-Switch type zone.
More than one attribute can be assigned for the zone. Pressing a digital button with the respective
number will activate a given attribute. Every activated attribute number is indicated as a lighting on
LED or enclosed in brackets number. Pressing the same digital button again will deactivate the attribute. At the end of this procedure, the LEDs or zone numbers, which correspond to the assigned
attributes only, will remain activated.
The parameters “ATTRIBUTES 3” are as follows:
1. Pulse /
Latch
24-hout Key-Switch type zone.
With assigned Pulse attribute every impulse will change alternatively the arming status of the system - respectively armed/ disarmed.
With assigned Latch attribute, if the zone is activated - the partition* is armed, if the zone is in normal operating status - the partition* is disarmed.
*The partition to which the zone is attached.
Attention: If the zone is attached to the both partitions in the system, its reaction will depend on the current partitions status. In the
SUPPLEMENT D are shown detailed algorithms for the partitions
reaction with Key-Switch type zone.
2. Full /Stay
This attribute determinates the arming type - FULL ARM or STAY
ARM.
Attribute
Pulse
Latch
Attribute
Full Arm
Stay Arm
3. Disarm
Enable
This attribute determinates whether the zone will disarm the system (DISARM ENABLED) or not (DISARM DISABLED).
Attribute
Disabled
Enabled
Default settings
- Disarm Enable attribute
Indication
LED
LCD


1
(1)
Indication
LED
LCD


2
(2)
Indication
LED
LCD


3
(3)
32
Installation and Programming Manual - СА62 Alarm Control Panel
ADDRESS 2014 - ZONE 1 ATTRIBUTES AUX
Zone 1
Attributes
AUX
At this address are assigned only parameters "ATTRIBUTES AUX" for Auxiliary type zone.
Only one attribute AUX can be assigned at this address - a number from 00 to 11.
With an assigned AUX attribute and alarm in the zone, a system status message will the generated in
the memory LOG file, which can be programmed to PGM output. The PGMx outputs programming is
described in item 3. PGM and SIREN Outputs Programming in SECTION Programming.
The indication is in hexadecimal numbers - see the Table in SUPPLEMENT С.
The parameters “ATTRIBUTES AUX” are as follows:
00
24h Burglary - 24-hour burglary alarm zone
With this attribute assigned the zone will be active irrespectively of the arming type. The zone will
operate as INSTANT type and the programmable ALARM and SIREN outputs, and the system communicator will be activated.
01
Battery Low - Low battery charging level.
02
Gas Detector - Activated gas detector.
03
Water Leakage - Activated flood detector.
04
AC Loss - Main power supply lost.
05
GSM Link Trouble - GSM communication failure.
06
Refrigeration - Activated refrigeration detector.
07
Loss of Heat - Loss of heat in the premises.
08
Foil Break - Detector foil break.
09
Low Bottled Gas Level - Activated low bottled gas detector.
10
High Temperature - High temperature in the premises.
11
Low Temperature - Low temperature in the premises.
Default settings
- 00. 24h Burglary attribute
ADDRESS 2015 - ZONE 1 ATTACHMENT
Zone 1
Attachment
At this address the ZONE 1 attachment to any of the two partitions in the system is assigned. To activate the parameter press the digit button with the respective partition number. Next pressing of the
same digit button will deactivate the parameter.
Note: The ZONE can be attached and to the both partitions in the system. In this case the E/E, Follow and Instant type zones will be armed only if the both partitions in the system are armed. Besides,
in case of alarm in a zone attached to the both partitions, records for the both of the partitions will be
present in the system memory LOG file.
Attention: If the ZONE is not attached to any of the both partitions in the system, the control panel will
not check and signalling for its state and status.
1. PART A
Partition А
The ZONE is attached to Partition A.
2. PART B
Partition B
The ZONE is attached to Partition B.
Default settings
Indication
LED

LCD
(1) 2 3 4 5 6
Indication
LED

LCD
1 (2) 3 4 5 6
- PART A
ADDRESSES 2020 ... 2025 - ZONE 2 PROGRAMMING
The programming is the same as that at ADDRESS 2010 - 2015, as the type, attributes (parameters 1, 2 and 3, AUX)
as the attachment of ZONE 2 are assigned.
The doubling zone type connection can be realized to ZONE 2 - see the Figure 6 c. The ZONE 2 corresponds to ZONE
8. The type of connection can be programmed at ADDRESS 2026 with setting the "4.Doubling" attribute.
Default settings - type Unused; ATTRIBUTES 1 - AUTOBYPASS and BYPASS; ATTRIBUTES 3 - Disarm Enable;
ATTRIBUTES AUX - 00. 24 h Burglary; Attachment - PART А
Installation and Programming Manual - СА62 Alarm Control Panel
33
ADDRESS 2026 - TYPE OF BALANCING FOR ZONE 2
The type of zone 2 balancing is selected at this address. Every consecutive pressing of a digital button alternatively changes the type of balancing. Display indications are given in the tables below.
Type of
balancing for The doubling zone type connection can be realized to ZONE 2 - see the Figure 6 c.
ZONE 2
Note: When connecting one fire detector to the zone do not assign any type of balancing for it. When
connecting 2 fire detectors to the zone you have to assign the 4.Doubling attribute!
1. EOL
Connecting of balancing resistor.
With or without TAMPER in the circuit.
EOL Connecting
Without TAMPER
With TAMPER
2. Fast/
Regular
Programmable sensitivity of the zone between 10
and 250ms.
Sensitivity
Regular (250ms)
Fast (10ms)
3. Power-up
delay
4. Doubling
The zone will be bypassed for a 120 second period after power-up of the system (that eliminated
the false alarms in the initial power-up of the control
panel).
Doubling zone connection. The parameter is assigned when the doubling zones connection is realized in the system. Activating this parameter will disable the setting of 1.EOL attribute at the beginning
of this address, as considers that the connecting of
balancing resistors in this case is with tamper in the
circuit.
Default settings
Power-up delay
Without zone bypass
Zone bypass (120 sec)
Mode
Single zone
Doubling zone
Indication
LED
LCD


1
(1)
Indication
LED
LCD


2
(2)
Indication
LED
LCD


3
(3)
Indication
LED
LCD


4
(4)
- no attribute is set
ADDRESS 2030 ... 2036 - ZONE 3 PROGRAMMING
The programming is the same as that at ADDRESS 2010 - 2015, as the type, attributes (parameters 1, 2 and 3, AUX)
as the attachment of ZONE 3 are assigned.
The doubling zone type connection can be realized to ZONE 3 - see the Figure 6 c. The ZONE 3 corresponds to ZONE
9. The type of connection can be programmed at ADDRESS 2036 with setting the "4.Doubling" attribute.
Default settings - type Unused; ATTRIBUTES 1 - AUTOBYPASS and BYPASS; ATTRIBUTES 3 - Disarm Enable;
ATTRIBUTES AUX - 00. 24 h Burglary; Attachment - PART А
ADDRESS 2040 ... 2046 - ZONE 4 PROGRAMMING
The programming is the same as that at ADDRESS 2010 - 2015, as the type, attributes (parameters 1, 2 and 3, AUX)
as the attachment of ZONE 4 are assigned.
The doubling zone type connection can be realized to ZONE 4 - see the Figure 6 c. The ZONE 4 corresponds to ZONE
10. The type of connection can be programmed at ADDRESS 2046 with setting the "4.Doubling" attribute.
Default settings - type Unused; ATTRIBUTES 1 - AUTOBYPASS and BYPASS; ATTRIBUTES 3 - Disarm Enable;
ATTRIBUTES AUX - 00. 24 h Burglary; Attachment - PART А
ADDRESS 2047 - NUMBER OF ACTIVATIONS IN ZONE 4 IN PULSE COUNT MODE
Zone 4
Pulse counter
The number of pulses for zone 4 in Pulse Count mode are entered at this address.
The indication is in hexadecimal numbers, as for LCD keyboards the entered value is also visible at the
last clock digit. The value for the pulse counter can be entered while the digit is blinking.
Values of between 0 and 9 pulses can be entered here. The 0 value blocks the Pulse Count mode and
the zone can then function with the regular time for detecting activation.
The working algorithm for zone 4 in Pulse Count mode has been clarified in
Item 2.6.
Default settings - 0
34
Installation and Programming Manual - СА62 Alarm Control Panel
ADDRESS 2050 ... 2056 - ZONE 5 PROGRAMMING
The programming is the same as that at ADDRESS 2010 - 2015, as the type, attributes (parameters 1, 2 and 3, AUX)
as the attachment of ZONE 5 are assigned.
The doubling zone type connection can be realized to ZONE 5 - see the Figure 6 c. The ZONE 5 corresponds to ZONE
11. The type of connection can be programmed at ADDRESS 2056 with setting the "4.Doubling" attribute.
Default settings - type Unused; ATTRIBUTES 1 - AUTOBYPASS and BYPASS; ATTRIBUTES 3 - Disarm Enable;
ATTRIBUTES AUX - 00. 24 h Burglary; Attachment - PART А
ADDRESS 2060 ... 2066 - ZONE 6 PROGRAMMING
The programming is the same as that at ADDRESS 2010 - 2015, as the type, attributes (parameters 1, 2 and 3, AUX)
as the attachment of ZONE 6 are assigned.
The doubling zone type connection can be realized to ZONE 6 - see the Figure 6 c. The ZONE 6 corresponds to ZONE
12. The type of connection can be programmed at ADDRESS 2066 with setting the "4.Doubling" attribute.
Default settings - type Unused; ATTRIBUTES 1 - AUTOBYPASS and BYPASS; ATTRIBUTES 3 - Disarm Enable;
ATTRIBUTES AUX - 00. 24 h Burglary; Attachment - PART А
ADDRESS 2070 ... 2075 - ZONE 7 PROGRAMMING
The programming is the same as that at ADDRESS 2010 - 2015, as the type, attributes (parameters 1, 2 and 3, AUX)
as the attachment of ZONE 7 are assigned.
Note: The ZONE 7 is a keyboard zone (it is in the keyboard just like the ZONE 1 - see also item 2.6). Every keyboard
can be recognized from the panel as ZONE 7. The programming of this function can be done at ADDRESS 7xx0 with
setting the 4.Keypad Zone attribute (xx is the address of the respective keyboard).
Default settings - type Unused; ATTRIBUTES 1 - AUTOBYPASS and BYPASS; ATTRIBUTES 3 - Disarm Enable;
ATTRIBUTES AUX - 00. 24 h Burglary; Attachment - PART А
ATTENTION: The ZONES 8 - 12 will be active only when the zone doubling connection is realized in the system. In
this case ZONE 2 corresponds to ZONE 8, ZONE 3 - to ZONE 9, etc. The zone doubling connection circuit is shown
on Figure 6c, as the respective detectors are terminated with 2.2 кΩ resistor. Besides to activate the ZONES 8 - 12
in the system, it is necessary to set the 4.Doubling attribute for the corresponding zone - see the description of the
ZONES 2 -6 programming.
ADDRESS 2080 ... 2085 - ZONE 8 PROGRAMMING
The programming is the same as that at ADDRESS 2010 - 2015, as the type, attributes (parameters 1, 2 and 3, AUX)
as the attachment of ZONE 8 are assigned.
Default settings - type Unused; ATTRIBUTES 1 - AUTOBYPASS and BYPASS; ATTRIBUTES 3 - Disarm Enable;
ATTRIBUTES AUX - 00. 24 h Burglary; Attachment - PART А
ADDRESS 2090 ... 2095 - ZONE 9 PROGRAMMING
The programming is the same as that at ADDRESS 2010 - 2015, as the type, attributes (parameters 1, 2 and 3, AUX)
as the attachment of ZONE 9 are assigned.
Default settings - type Unused; ATTRIBUTES 1 - AUTOBYPASS and BYPASS; ATTRIBUTES 3 - Disarm Enable;
ATTRIBUTES AUX - 00. 24 h Burglary; Attachment - PART А
ADDRESS 2100 ... 2105 - ZONE 10 PROGRAMMING
The programming is the same as that at ADDRESS 2010 - 2015, as the type, attributes (parameters 1, 2 and 3, AUX)
as the attachment of ZONE 10 are assigned.
Default settings - type Unused; ATTRIBUTES 1 - AUTOBYPASS and BYPASS; ATTRIBUTES 3 - Disarm Enable;
ATTRIBUTES AUX - 00. 24 h Burglary; Attachment - PART А
ADDRESS 2110 ... 2115 - ZONE 11 PROGRAMMING
The programming is the same as that at ADDRESS 2010 - 2015, as the type, attributes (parameters 1, 2 and 3, AUX)
as the attachment of ZONE 11 are assigned.
Default settings - type Unused; ATTRIBUTES 1 - AUTOBYPASS and BYPASS; ATTRIBUTES 3 - Disarm Enable;
ATTRIBUTES AUX - 00. 24 h Burglary; Attachment - PART А
ADDRESS 2120 ... 2125 - ZONE 12 PROGRAMMING
The programming is the same as that at ADDRESS 2010 - 2015, as the type, attributes (parameters 1, 2 and 3, AUX)
as the attachment of ZONE 12 are assigned.
Default settings - type Unused; ATTRIBUTES 1 - AUTOBYPASS and BYPASS; ATTRIBUTES 3 - Disarm Enable;
ATTRIBUTES AUX - 00. 24 h Burglary; Attachment - PART А
Installation and Programming Manual - СА62 Alarm Control Panel
35
3. PGM and SIREN Outputs Programming
ADDRESS 3010 - PGM1 ATTRIBUTES 1 PROGRAMMING
PGM 1
Attributes 1
The events "ATTRIBUTES 1", which activate the programmable output PGM 1, are programmed at
this address.
An arbitrary combination of events, which activate the programmable output, is allowed. The output is
activated upon the occurrence of any of the programmed events and is restored when all programmed
events are discarded.
Press a digital button, which corresponds, to a given attribute (alarm event). The attribute is selected
when the light-emitting diode on the display (LED keyboards) or an enclosed in brackets number (LCD
keyboards) with the respective number is activated. Next pressing of the same digit button will deactivate the attribute.
1. ALARM
It is activated when Entry\Exit, Follow and Instant type zones are violated while the system is in armed
mode and "00.24-hour burglary alarm zone" attribute is set at ADDRESS 2014, irrespective of the arm
mode.
• With set attribute Pulse the output is restored after a valid user code is entered, restoring of the
activated zone or following an interval of 1 min.
• With set attribute Latch the output is restored after a valid user code with disarming rights is entered
or after confirmation for stopping the alarm if the system is disarmed.
2. PANIC
It is activated when the PANIC type zone is triggered or when PANIC is triggered from the keyboard.
• With set attribute Pulse the output is restored after a valid user code is entered or following an
interval of 1 min.
• With set attribute Latch the output is restored after a valid user code with disarming rights is entered
or after confirmation for stopping the alarm if the system is disarmed.
3. TAMPER
It is activated when TAMPER is triggered off in any zone or periphery device, irrespective of the arm
mode. It is restored after activation is discarded and does not depend on the Pulse / Latch attribute.
4. FIRE
It is activated when a FIRE type zone is triggered.
• With set attribute Pulse the output is restored after a valid user code is entered or following an
interval of 1 min.
• With set attribute Latch the output is restored after a valid user code with disarming rights is entered
or after confirmation for stopping the alarm if the system is disarmed.
5. FIRE
RESET
It is activated for 4 sec. after a valid code is entered.
6. ON / OFF
It is activated by a command to arm the whole system (partition A and partition B). Output is restored
after disarming of any of the partitions (A or B) and does not depend on the Pulse / Latch attribute.
Default settings
- ALARM
ADDRESS 3011 - PGM1 ATTRIBUTES 2 PROGRAMMING
PGM 1
Attributes 2
The events "ATTRIBUTES 2", which activate the programmable output PGM 1, are programmed at
this address.
An arbitrary combination of events, which activate the programmable output, is allowed. The output is
activated upon the occurrence of any of the programmed events and is restored when all programmed
events are discarded.
Press a digital button, which corresponds, to a given attribute (alarm event). The attribute is selected
when the light-emitting diode on the display (LED keyboards) or an enclosed in brackets number (LCD
keyboards) with the respective number is activated. Next pressing of the same digit button will deactivate the attribute.
1. MEDICAL
It is activated when a MEDICAL type zone is triggered.
• With set attribute Pulse the output is restored after all MEDICAL type zones are restored.
• With set attribute Latch the output is restored after all MEDICAL type zones are restored, after a
valid user code with disarming rights is entered or after confirmation for stopping the alarm if the system is disarmed.
2. PS /
BYPASS
It is activated right after a zone has been designated to be bypassed or when the zone has been assigned a Stay ARM and Instant ARM type arming. Output is restored after de-bypassing of all zones
or after disarming.
ADDRESS 3011 description continues on page 36 
36
Installation and Programming Manual - СА62 Alarm Control Panel
3. SIREN
The output is activated, when there is an alarm event in the system.
For all kinds alarm events the siren will activate for programmed bell time for the respective partition
(at ADDRESS 4012 for Partition А and ADDRESS 4022 for Partition В) or until a valid user code is
entered.
In case of alarm event in FIRE type zone, the siren is activated in sequence of impulses (1 second on,
1 second off) until a valid user code is entered. With Fire Duration bell time set at ADDRESSES 4015
and 4025, the “SIREN” output will be restored when the bell time is over or after a valid user code is
entered.
4. TECH.
TRBL
It is activated in case of occurring "Low BATT", "Tel line fault" or "Blown fuse" events.
• With set attribute Pulse the output is restored after a valid user code is entered or following an
interval of 1 min.
• With set attribute Latch the output is restored after a valid user code with disarming rights is entered
or after confirmation for stopping the alarm if the system is disarmed.
5. PULSE /
LATCH
The output way of activation (restoring) is assigned at this address.
In SUPPLEMENT D are shown detailed algorithms for Key-Switch type
zone operation.
6. POLARITY The active level for activation of the output is assigned at this address.
Attribute
Pulse
Latch
LED
LCD


5
(5)
Indication
Active
level
0V
+12V
Default settings
Indication
LED
LCD


6
(6)
- POLARITY /+12V/
ADDRESS 3012 - PGM1 ATTACHMENT
PGM 1
Attachment
At this address the PGM 1 attachment to any of the two partitions in the system is assigned. The output
can be attached to the both partitions in the system at the same time.
1. PART A
Partition А
The PGM is attached to Partition A. (It is activated in
case of event in the Partition A.)
2. PART B
Partition В
The PGM is attached to Partition B. (It is activated in
case of event in the Partition B.)
Default settings
Indication
LED

LCD
(1) 2 3 4 5 6
Indication
LED

LCD
1 (2) 3 4 5 6
- PART A
ADDRESS 3013 - PGM 1 EXTENSIONS
PGM 1
Extensions
At this address the PGM1 EXTENSIONS parameters are assigned. The output can be activated in
case of 20 additional events occurring. The engineer have to enter one two digit number of the additional parameter - from 00 to 19. The description of the parameters is given in the table below.
00.
No additional parameter for PGM 1 output is assigned.
No Extention
01.
Battery
Trouble
The output is activated in case of lowering the accumulator voltage under 11.4V, damaged battery fuse
(BATT) or missing battery.
The output is restored after the charging level of the battery reaches value of 11.8V. The restoration of
the output does not depend on the Pulse / Latch parameter.
02.
Blown
Fuse
The output is activated in case of blown out fuse (activated PTC fuse).
- When the Pulse parameter is assigned (see ADDRESS 3011) the output is restored after entering
of a valid user code or after 1 minute.
- When the Latch parameter is assigned (see ADDRESS 3011) the output is restored after resetting
(recovering) of the fuse.
ADDRESS 3013 description continues on page 37 
Installation and Programming Manual - СА62 Alarm Control Panel
37
03.
Telephone
Line
Trouble
The output is activated in case of trouble or missing of the telephone line
The possible activating events are:
• telephone line is missing
• "Dialing tone" is missing
• no communication with Monitoring station 1
• no communication with Monitoring station 2
This parameter does not depend of programmed Pulse/ Latch parameter. The output always follows
the event.
04.
AC LOSS
Control
Panel
MainBoard
The output is activated in case of trouble in the main power supply of the control panel (control panel
PCB).
05.
AC LOSS
From Zone
The output is activated in case of activating of a ZONE with assigned Auxiliary type and AC LOSS attribute - for controlling of devices working together with the control panel, for example additional power
supply devices. In case of loss of the power supply of the ZONE, the control panel will send a message
for trouble.
06.
KEYPAD
ALARM
The output is activated in case of an alarm signal:
• for FIRE in the system (for LED62)
• MEDICAL Alarm (for LED62)
• PANIC (for all types of keyboards)
• in case of entering 3 wrong codes in sequence
• TAMPER from a keyboard
• BLOCKED keyboard
The output is activated in case of sending of FIRE signal - the FIRE button of LED62 (
07.
KEYPAD FIRE pressed and held on for 3 seconds.
ALARM
Note: This parameter can be programmed only for LED62 keyboard!
) is
08.
KEYPAD
PANIC
ALARM
The output is activated in case of sending of PANIC alarm signal - the buttons CLR+ENT are pressed
and held on for 3 seconds.
Note: For LED62 keyboard this parameter can be programmed for the PANIC button .
09.
DURESS
ALARM
The output is activated in case of sending of "AMBUSH CODE" (also known as DURESS CODE).
The AMBUSH CODE is a personal code. The User can use the AMBUSH CODE if he is forced to disarm the system. When an AMBUSH CODE is entered the system will be disarmed and a TROUBLE
signal will be send to a central monitoring station.
The AMBUSH CODE for every user code is generated with adding 1 to the last digit. If the last digit of
the code is 9 it is replaced with 0.
Example: Personal User Code: 4615 → Ambush Code: 4616
Personal User Code: 4619 → Ambush Code: 4610
10. CHIME
The output is activated in case of sending of CHIME signal from a zone with assigned CHIME attribute.
The output is restored automatically after 2-3 seconds and does not depend on the programming of
the Pulse / Latch parameter.
Note: The output depends on the programmed PARTITION attachment - for the zone and the PGM
output MUST be attached to one and the same PARTITION.
11.
AUXILIARY
ALARM
The output is activated in case of sending of alarm signal from zones with assigned AUXILIARY attribute and is restored when all AUXILIARY type zones are deactivated.
12.
BATTERY
TROUBLE
The output is activated in case of sending of alarm signal from AUXILIARY type zones with assigned
BATT LOW attribute.
13.
Wireless
The output is activated in case of sending an alarm signal for wireless transmiter loss from AUXILIARY
Transmitter type zone with "GSM Link Trouble" assigned attribute.
Supervision
Loss
14.
Wireless
The output is activated in case of wireless transmitter low battery charge or battery loss from AUXILTransmitter IARY type zone with "Battery Low" assigned attribute.
Battery Low
ADDRESS 3013 description continues on page 38 
38
Installation and Programming Manual - СА62 Alarm Control Panel
15.
AUTO-ARM
The output is activated in case of assigned "Auto-Arm" (Automatic arming of the system) attribute for
PARTITION А (ADDRESS 4016), PARTITION В (ADDRESS 4026) or for both partitions. The output is
restored with disarming of the system and does not depend on Pulse/Latch programming.
16.
Video-OnArmed
The output is activated when an already armed zone with assigned "VIDEO-ON-ARMED" attribute
is violated. "VIDEO-ON-ARMED" means that there is a video surveillance recording in the secured
area.
This parameter is valid for the programmed on ADDRESS 3014 (PGM1 EXTENSION X1).
When using the doubling zone connection of the detectors in the system, there is a relation between
the used zones - ZONE1 corresponds to ZONE7, ZONE2 corresponds to ZONE8 and so on up to
ZONE6 which corresponds to ZONE12. In this case the number of corresponding zone (7 - 12) have
to be assigned to ADDRESS 3015 (PGM1 EXTENSION X2).
The output is restored automatically after 1 minute and does not depend on the entered user codes or
the Pulse/Latch programming.
17.
Zone
Violation
The output is activated in case of opening (activating) of ZONES which numbers are assigned at ADDRESSES 3хх4 or 3хх5.
The output is deactivated when the assigned ZONES at ADDRESSES 3хх4 and 3хх5 are restored,
and does not depend on the arming mode - the output operates and in the ARM and in the DISARM
mode.
18.
Code Used
Signaling
The output is activated at:
• entering a code
• entering and AMBUSH CODE
• approaching a proxi card to the proximity reader
• programming of a selected user code
The output is restored automatically after 4-5 seconds and does not depend on the arming mode and
the Pulse/Latch programming.
19.
Proximity
Card Used
Signaling
The output is activated when approaching a proximity card to a selected proximity reader.
The output is restored after 2-3 seconds and does not depend on the Pulse/Latch programming. The
output does not depend also on the assigned PARTITION attachment of the code and the proximity
reader.
ADDRESS 3014 - PGM 1 EXTENSION X1
PGM 1
Extension
X1
At this address, as additional PGM1 attributes, are programmed code numbers for extensions from
156to 19 assigned at ADDRESS 3013.
User code or zone numbers from 1 to 6 are assigned.
To activate the parameter press the digit button with the corresponding number. The next pressing of
the same digit button will deactivate the parameter.
ADDRESS 3015 - PGM 1 EXTENSION X2
PGM 1
Extension
X2
At this address, as additional PGM1 attributes, are programmed code numbers for extensions from 16
to 19 assigned at ADDRESS 3013.
User code or zone numbers from 7 to 12 are assigned.
To activate the parameter press the digit button with the corresponding number. The next pressing of
the same digit button will deactivate the parameter.
ADDRESS 3016 - PGM 1 EXTENSION X3
PGM 1
Extension
X3
At this address, as additional PGM1 attributes, are programmed code numbers for extensions from 18
and 19 assigned at ADDRESS 3013.
User code numbers from 13 to 18 are assigned.
To activate the parameter press the digit button with the corresponding number. The next pressing of
the same digit button will deactivate the parameter.
ADDRESS 3017 - PGM 1 EXTENSION X4
PGM 1
Extension
X4
At this address, as additional PGM1 attributes, are programmed code numbers for extensions from 18
and 19 assigned at ADDRESS 3013.
User code numbers from 19 to 20 are assigned.
Manager code number from 1 to 3 and/or Chief manager code are assigned.
To activate the parameter press the digit button with the corresponding number. The next pressing of
the same digit button will deactivate the parameter.
Installation and Programming Manual - СА62 Alarm Control Panel
39
ADDRESS 3018 - PGM 1 DEVICE ID (Keyboards)
PGM 1
Device ID
At this address a number of a keyboard from 1 to 6 for PGM1 extension attribute 18 assigned to ADDRESS 3013.
To activate the parameter press the digit button with the corresponding number. The next pressing of
the same digit button will deactivate the parameter.
ADDRESS 3019 - PGM 1 DEVICE ID (Keyboards / Proxi Readers)
PGM 1
Device ID
At this address a number of a keyboard from 7 or 8 and a proximity reader number from 1 to 4 for
PGM1 extensions attributes 18 and 19 assigned to ADDRESS 3013.
To activate the parameter press the digit button with the corresponding number. The next pressing of
the same digit button will deactivate the parameter.
ADDRESSES 3020 ... 3029 - PROGRAMMING OF PGM 2
The programming is the same as at ADDRESSES from 3010 to 3019, as here are assigned the attributes (1 and 2),
attachment, extensions (00 - 19 and Х1 - Х4) and ID number for PGM2.
Default settings - Attributes 1 - ALARM; Attributes 2 - POLARITY, Attachment - PARTITION A
ADDRESSES 3030 ... 3039 - PROGRAMMING OF PGM 3
The programming is the same as at ADDRESSES from 3010 to 3019, as here are assigned the attributes (1 and 2),
attachment, extensions (00 - 19 and Х1 - Х4) and ID number for PGM3.
Default settings - Attributes 1 - ALARM; Attributes 2 - POLARITY, Attachment - PARTITION A
ADDRESSES 3040 ... 3049 - PROGRAMMING OF SIREN OUTPUT (PGM 4)
The programming is the same as at ADDRESSES from 3010 to 3019, as here are assigned the attributes (1 and 2),
attachment, extensions (00 - 19 and Х1 - Х4) and ID number for PGM4.
By default the SIREN output is indended for siren connection with assigned SIREN attribute at ADDRESS
3041.
Default settings - Attributes 2 - POLARITY and SIREN, Attributes - PARTITION A
40
Installation and Programming Manual - СА62 Alarm Control Panel
4. PARTITIONS PROGRAMMING
At ADDRESSES 40хх are assigned the attributes of the А and В partitions in the system. Every partition can be armed
and disarmed independently.
ADDRESS 4010 - PROGRAMMING OF EXIT TIME FOR PARTITION А
Exit Time
Partition А
Exit time is assigned to Entry/Exit type zones attached to Partition A. A double-digit number between 1
and 99 seconds is entered. For an interval of time, less than 10 seconds, the first digit must be 0.
The indication is hexadecimal and the digits are displayed one by one. To view the introduced data, the
digits can be browsed with the help of the arrows.
Default settings - 45 sec.
ADDRESS 4011 - PROGRAMMING OF ENTRY TIME FOR PARTITION А
Entry Time
Partition А
Entry time is assigned to Entry/Exit type zones attached to Partition A. A double-digit figure between 1
and 99 seconds is entered. For a time interval of less than 10 seconds, the first digit must be 0.
The indication is hexadecimal and the digits are displayed one by one. To view the introduced data, the
digits can be browsed with the help of the arrows.
Default settings - 15 sec.
ADDRESS 4012 - PROGRAMMING OF BELL TIME FOR PARTITION А
Bell Time
Partition А
Duration is set for the bell time of the sirens attached to Partition A. A double-digit numberbetween 0
and 99 minutes is entered. For a time interval of less than 10 seconds, the first digit must be 0.
The indication is hexadecimal and the digits are displayed one by one. To view the introduced data, the
digits can be browsed with the help of the arrows.
Default settings - 03 min.
ADDRESS 4013 - PROGRAMMING OF BELL DELAY FOR PARTITION А
Bell Delay
Partition А
Delay is set for initiating the bell time of the sirens attached to Partition A. A double-digit number between 0 and 99 seconds is entered. For a time interval of less than 10 seconds, the first digit must be
0.
The indication is hexadecimal and the digits are displayed one by one. To view the introduced data, the
digits can be browsed with the help of the arrows.
Default settings - 0 min.
ADDRESS 4014 - PROGRAMMING OF AUTO-ARM TIME FOR PARTITION А
Auto-ARM
Time
Partition А
A time (HH:MM) for automatic arming at Partition A in the system is set.
Note: To take effect the programmed time on this address it is necessary the attribute "3. Auto Arm
Enbl." at ADDRESS 4016 to be assigned.
ADDRESS 4015 - FIRE SIGNAL DURATION FOR PARTITION А
FIRE Signal
Duration
Partition А
The duration of the alarm signal for a FIRE event at Partition A is assigned at this address.
Programming this address affects the performance of the programmable SIREN output.
Every click of a digital button alternatively changes the type of duration of the sound signal. The display
indication is shown in the tables.
Until a valid
There is a FIRE alarm signal until a valid system
user code is
user or master user code is introduced.
entered
Until the Bell
Time at
The FIRE signal duration is set at address 4012
Address
BELL TIME.
4012 ends.
Default settings - Until a valid user code is entered
Indication
LED

LCD
1 2 3 4 5 6
Indication
LED

LCD
(1) (2) (3) (4) (5) (6)
Installation and Programming Manual - СА62 Alarm Control Panel
41
ADDRESS 4016 - PROGRAMMING OF ATTRIBUTES FOR PARTITION А
Attributes
Partition А
The attributes of Partition A are programmed at this address. Every attribute is activated with pressing
of a digit button with a respective number (from 1 to 4). The choosen attribute is indicated with activated number of the pressed digit.
Next pressing of the same button number will deactivate the attribute. At end of the procedure at the
keyboard dispaly have to active only the numbers of the assigned attributes.
More than one attribute can be assigned at this address.
1. Sqwk
ARM
The siren will activate singly for 1 second when arming the Partition A in the system.
2. Sqwk
DISARM
The siren will activate twice when disarming the Partition A in the system.
3. Auto-Arm
Enbl
Enabling the automatic arming of Partition A in the system for the
programmed ar ADDRESS 4014 Auto-ARM time.
Auto-Arm
Enbl
Disabled
Enabled
4. Auto Arm
Full/Stay
Automatic arming the Partition A with specifing the arming mode:
• Full
• Stay (the User can stay at some rooms).
Attribute
Full
Stay
Indication
LED
LCD


3
(3)
Indication
LED
LCD


4
(4)
ADDRESS 4017 - NUMBER FOR COMMUNICATION WITH PARTITION А
Number for A number for communication between Partitin A and a central monitoring station is entered at this adcommunica- dress.
tion
4 digits have to be enetered. The valid digits are from 0 to 9 anf symbols from A to F.
Default settings - FFFF
ADDRESSES 4020 ... 4024 - PROGRAMMING OF THE ATTRIBUTES FOR PARTITION B
The programming is the same as for ADDRESS 4010 - 4014.
Default settings - Same as PARTITION A
ADDRESS 4025 - FIRE SIGNAL DURATION FOR PARTITION B
FIRE Signal
Duration
Partition B
The duration of the alarm signal for a FIRE event at Partition A is assigned at this address.
Programming this address affects the performance of the programmable SIREN output.
Every click of a digital button alternatively changes the type of duration of the sound signal. The display
indication is shown in the tables.
Until a valid
There is a FIRE alarm signal until a valid system
user code is
user or master user code is introduced.
entered
Until the Bell
Time at
The FIRE signal duration is set at address 4022
Address
BELL TIME.
4012 ends.
Indication
LED
LCD
1 2 3 4 5 6

Indication
LED

LCD
(1) (2) (3) (4) (5) (6)
Default settings - Until a valid user code is entered
ADDRESSES 4026 and 4027 - PROGRAMMING OF THE ATTRIBUTES FOR PARTITION B
The programming is the same as for ADDRESS 4016 and 4017.
Default settings - Same as PARTITION A
42
Installation and Programming Manual - СА62 Alarm Control Panel
6. PROGRAMMING OF COMMUNICATION DEVICES
At ADDRESSES 60хх are programmed common parameters of the connected to the system communication devices.
Note: Delete the queue of events to be sent to Address 0023 by single pressing the 0 button before configuring communicator parameters of the digital communicator.
ADDRESS 6001 - NUMBER OF COMMUNICATION ATTEMPTS
Assign the number of attempts to connect to the central station for telephone monitoring and the
number of repetitions of voice messages at this address that the Control Panel will make in case of
unsuccessful communication or failure to acknowledge voice messages.
The value assigned at this address is the number of attempts to be made for each of the telephones
configured at addresses 6010 and 6020 - for the digital communicator, and at addresses 6031, 6032,
6033 and 6034 - for the voice dialer. (Example: if the assigned value is 4 and two telephone numbers,
the number of attempts which will be made are 8 - 4 for each telephone number). Any messages to the
central station will have priority. The attempts to connect to the central station will be terminated after
the assigned number is reached. Transmission of the occurred events begins via the voice dialer to
Number of
the telephones at addresses 6031 to 6034. The panel waits for 2 sec. after each “individual message”
communicain order to receive a message reception acknowledgement.
tion attempts
This is confirmed when the user presses key 9 on the telephone. The time needed to transmit one
group of voice messages, where no confirmation has been received, is up to 1 minute. The transmission to the other telephones begins after confirmation has been received from one single telephone.
After the assigned number of voice message transmissions is reached, the attempts to transmit voice
messages will be terminated. The attempts to transmit will be renewed to the central station first, when
the next transmission event occurs.
The values between 0 and 9 are permitted. The desired value is entered by single-pressing the key of
the respective figure. Where the value of 0 is entered, the panel will automatically implicate the value
of 4 for the central station and the value of 2 for the voice dialer.
Default settings - 0
ADDRESS 6002 - TEST MESSAGE TRANSMITTING PERIOD
Test period
Duration of transmission of test message in hours (HH) from 00 to 99 is entered.
The indication is hexadecimal.
Two digits must be entered. When entering a period shorter than 10 hours the first digit must
be 0.
Default settings - 24 hours
ADDRESS 6003 - SETTING TEST START TIME FOR SENDING MESSAGE
Test start
time
At this address is set the first hour, at which the test message will start to be transmitted to central
monitoring station. Hours and minutes are entered (HH:MM), as the entered time is the time of starting the first test.
The next test time will start after the assigned at ADDRESS 6002 test period.
The indication is hexadecimal.
Default settings - 00:05 h.
ADDRESS 6010 - ENTERING TELEPHONE NUMBER 1 FOR THE COMMUNICATOR
Telephone
number 1
for the communicator
A telephone number is assigned for communicating with central station - No. 1.
The indication is hexadecimal. The telephone number must not exceed 16 characters.
Some special functions can be entered by using the next button combinations:
1. Buttons ARM + 0 - Switches on "pulse dialer".
2. Buttons ARM + 1 - Switches on "tone dialer".
3. Buttons ARM + 2 - 2 seconds pause.
4. Buttons ARM + 3 - Switches on "Wait dial tone".
5. Buttons ARM + 4 - "Blind dialing"; Switches off "Wait dial tone".
6. Buttons ARM + 5 - Deletes the entered telephone number.
Dialing has been assigned a default tone signal and "Wait dial tone" function is switched on.
The entered telephone number and the special functions can be saved with pressing the ENT button.
Default settings - there are no configured numbers, tone dialer
Installation and Programming Manual - СА62 Alarm Control Panel
43
ADDRESS 6011 - ENTERING PROTOCOL 1 NUMBER FOR THE COMMUNICATOR
Enter central station No. 1 protocol number from the attached table. Valid are the symbols from 1 to
2, where:
PROTOCOL 1
Indication
Button
Protocol
1
ADEMCO CONTACT ID*
2
SIA*
LED
LCD


1 2 3 4 5 (6)
1 2 3 4 (5) 6
* Note: See also the code tables in the APPENDIX C.
Default settings - ADEMCO CONTACT ID
ADDRESS 6012 - TYPES OF MESSAGES TRANSMITTED FROM THE DIGITAL COMMUNICATOR FOR PROT. 1
Message
type
At this address are assigned the type of the messages which will be transmitted to a central monitoring
station in case of alarm condition through telephone number 1. Here also is assigned and the transmitting algorithm of the messages. The following report options can be set:
1. Message report from at least one of the two telephone numbers - Alternative report.
2. Independent message report to both telephone numbers - Split report.
3. Message report from one telephone number, which is also duplicated at the second - Both report.
Note: To the telephone number 1 can be programmed to be transmitted only chosen messages. In
case the user wants some messages to be transmitted and through telephone number 2, then the
same chosen messages have to be assigned and at ADDRESS 6022. If it does not matter through
which of the both telephone numbers, 1 and/or 2, the messages are sent, you have to leave the ADDRESS 6022 with its default programming (No messages are assigned).
The digital buttons 1 to 6 are used for programming. Pressing them each time will alternatively change
the status of the respective message type - report (active status of the parameter) or no report (inactive
status of the parameter). At the end of the procedure only those parameters, which correspond to the
designated for report messages, should remain activated on the display.
At the default settings the display will show:
LED

LCD
(1) (2) (3) (4) (5) (6)
1. ALARM
ALARM and TAMPER type messages are transmitted.
2. PANIC
PANIC type messages or entered ambush code are transmitted.
3. FIRE
FIRE and TAMPER type messages are transmitted.
4.ON/
OFF+BPS
BYPASS, ON/OFF type messages and engineer programming input are transmitted.
5. MEDICAL
MEDICAL type messages are transmitted.
6. TROUBLE TROUBLE and TEST type messages are transmitted.
Default settings - ALARM, PANIC, FIRE, ON/OFF+BPS, MEDICAL and TROUBLE
ADDRESS 6020 - ENTERING TELEPHONE NUMBER 2 FOR THE COMMUNICATOR
Telephone
number 2
for the communicator
A telephone number is assigned for communicating with central station - No. 2.
The indication is hexadecimal. The telephone number must not exceed 16 characters.
Some special functions can be entered by using the next button combinations:
1. Buttons ARM + 0 - Switches on "pulse dialer".
2. Buttons ARM + 1 - Switches on "tone dialer".
3. Buttons ARM + 2 - 2 seconds pause.
4. Buttons ARM + 3 - Switches on "Wait dial tone".
5. Buttons ARM + 4 - "Blind dialing"; Switches off "Wait dial tone".
6. Buttons ARM + 5 - Deletes the entered telephone number.
Dialing has been assigned a default tone signal and "Wait dial tone" function is switched on.
The entered telephone number and the special functions can be saved with pressing the ENT button.
Default settings - there are no configured numbers, tone dialer
44
Installation and Programming Manual - СА62 Alarm Control Panel
ADDRESS 6021 - ENTERING PROTOCOL 2 NUMBER FOR THE COMMUNICATOR
Enter central station No. 1 protocol number from the attached table. Valid are the symbols from 1 to
2, where:
PROTOCOL 2
Button
Protocol
1
ADEMCO CONTACT ID*
2
SIA*
Indication
LED
LCD


1 2 3 4 5 (6)
1 2 3 4 (5) 6
* Note: See also the code tables in the APPENDIX C.
Default settings - ADEMCO CONTACT ID
ADDRESS 6022 - TYPES OF MESSAGE TRANSMITTED FROM THE DIGITAL COMMUNICATOR, FOR PROT. 2
Messages
The programming is the same as for ADDRESS 6012.
Default settings - No messages are assigned
ADDRESS 6030 - RECORDING AND LISTENING OF VOICE MESSAGES
VD60 Voice
Dialer Programming
You can record and listen to messages in the voice dialer at this address.
At APPENDIX Е is given a detailed algorithm for recording and listening to of the voice messages.
Note: Recording and listening of voice messages can be done only if a voice dialer VD60 is integrated
to the CA62 control panel (main PCB ).
ADDRESS 6031 - ENTERING TELEPHONE NUMBER 1 FOR THE DIALER
A telephone number is assigned for communicating via voice dialer No. 1. The indication is hexadecimal. The telephone number must not exceed 16 characters
Some special functions can be entered by using the next button combinations:
1. Buttons ARM + 0 - Switches on "pulse dialer".
2. Buttons ARM + 1 - Switches on "tone dialer".
Telephone
number 1 for 3. Buttons ARM + 2 - 2 seconds pause.
4. Buttons ARM + 3 - Switches on "Wait dial tone".
the dialer
5. Buttons ARM + 4 - "Blind dialing"; Switches off "Wait dial tone".
6. Buttons ARM + 5 - Deletes the entered telephone number.
Dialing has been assigned a default tone signal and "Wait dial tone" function is switched on.
The entered telephone number and the special functions can be saved with pressing the ENT button.
Default settings - there are no configured numbers
ADDRESS 6032 - ENTERING TELEPHONE NUMBER 2 FOR THE DIALER
Telephone
A telephone number is assigned for communicating via voice dialer No. 2.
number 2 for
The programming is the same as at the ADDRESS 6031.
the dialer
Default settings - there are no configured numbers
ADDRESS 6033 - ENTERING TELEPHONE NUMBER 3 FOR THE DIALER
Telephone
A telephone number is assigned for communicating via voice dialer No. 3.
number 3 for
The programming is the same as at the ADDRESS 6031.
the dialer
Default settings - there are no configured numbers
ADDRESS 6034 - ENTERING TELEPHONE NUMBER 4 FOR THE DIALER
Telephone
A telephone number is assigned for communicating via voice dialer No. 4.
number 4 for
The programming is the same as at the ADDRESS 6031.
the dialer
Default settings - there are no configured numbers
Installation and Programming Manual - СА62 Alarm Control Panel
45
ADDRESS 6035 - GROUPS OF MESSAGES FOR VOICE DIALER TRANSMISSION
VD60 group
messages
Programming the groups of message to be transmitted by the voice dialer at this address. The possible
options are 0 and 1. The status of the parameter is changed with pressing a random digit number.
At SUPPLEMENT E - Examples for voice messages, are shown an examples for voice messages for
zones and events.
Indication
0 (Zone)
Transmitting messages by zones.
LED

LCD
1 2 3 4 5 6
Indication
1 (Events)
Transmitting messages by events.
LED

LCD
(1) (2) (3) (4) (5) (6)
Default settings - 1 (Events)
At the ADDRESSES 69хх are set the parameters for up / download programming of the integrated digital communicator
and the VD60 voice dialer.
ADDRESS 6900 - TELEPHONE NUMBER FOR UP / DOWN LOAD PROGRAMMING
Tel. number
for Up /
Download
An up / down load PC telephone number can be set at this address.
The indication is hexadecimal. The telephone number must not exceed 16 characters.
Some special functions can be entered by using the next button combinations:
1. Buttons ARM + 0 - Switches on "pulse dialer".
2. Buttons ARM + 1 - Switches on "tone dialer".
3. Buttons ARM + 2 - 2 seconds pause.
4. Buttons ARM + 3 - Switches on "Wait dial tone".
5. Buttons ARM + 4 - "Blind dialing"; Switches off "Wait dial tone".
6. Buttons ARM + 5 - Deletes the entered telephone number.
Dialing has been assigned a default tone signal and "Wait dial tone" function is switched on.
The entered telephone number and the special functions can be saved with pressing the ENT button.
Default settings - there are no configured numbers, tone dialer
ADDRESS 6901 - PERSONAL COMPUTER IDENTIFICATION NUMBER FOR UP / DOWN LOADING
PC ID
The PC ID number for up / down loading is configured at this address.
Four digits can be introduced. Valid are symbols 0 to 9.
The entered number is saved with pressing the ENT button.
Default settings - 1234
ADDRESS 6902 - CONTROL PANEL IDENTIFICATION NUMBER
Panel ID
The control panel up/down loading ID number is entered at this address.
Four digits can be introduced. Valid are symbols 0 to 9.
The entered number is saved with pressing the ENT button.
Default settings - 1234
46
Installation and Programming Manual - СА62 Alarm Control Panel
ADDRESS 6903 - CALL BACK FUNCTION
Call Back
Function
This address enables the CALL BACK option function. Every push of the digital button alternatively
changes enabled to disabled status.
The connection fails if an allowed Call Back function is enabled during an incoming exchange request
to up / down load from a PC. The control panel selects the number specified at Address 6900 and an
up / down load procedure is initiated.
The display indication on the keypad is described below.
Indication
NO
The Call Back function is disabled.
LED

LCD
1 2 3 4 5 6
Indication
YES
The Call Back function is enabled.
LED

LCD
(1) (2) (3) (4) (5) (6)
Default settings - NO
ADDRESS 6904 - NUMBER OF RINGS
Number of
rings
The symbols 0 to 9 are used.
RINGS Up/ down loading is disabled if 0 is entered.
ATTENTION: It is recommended this parameter does not exceed the value of 7!
Default settings - 7
ADDRESS 6905 - ANSWERING MACHINE FUNCTION
Answering
machine
This address enables the Answering Machine function for up / down loading. Every push of the digital
button alternatively changes enabled to disabled status.
Priority should be given to any automatic answering devices (like FAX or telephone answering machines), if such are connected to the telephone line.
The Answering Machine function should be enabled in such cases. During initial income of a series of
calls (rings), the CA62 temporizes the maximum number of calls, set at Address 6904. The automatic
answering machine must be adjusted to a fewer number of rings. If within four minutes there is another
series of incoming calls the CA62 shall answer the first one.
The display indication is shown in the tables below.
Indication
NO
The "Answering machine" function is disabled.
LED

LCD
1 2 3 4 5 6
Indication
YES
The "Answering machine" function is enabled.
Default settings - NO
LED

LCD
(1) (2) (3) (4) (5) (6)
Installation and Programming Manual - СА62 Alarm Control Panel
47
7. PROGRAMMING OF PERIPHERAL DEVICES
At ADDRESSES 70хх are programmed the parameters and the attributes for the connected to the system keyboards.
Up to 8 keyboards can be connected in the system.
ATTENTION:
The keyboards models LED61, LED63, LCD62 and LCD62B DO NOT SUPPORT SIMULTANEOUSLY OPERATION WITH THE BOTH PARTITIONS A and B.
Simultaneously operation with A and В partitions is supported from LED62, LCD63SE, LCD64 keyboards.
ADDRESS 7000 - CHECKING THE SET KEYBOARD ADDRESS
Keyboard
address
At this address the set with jumpers address of each keyboard can be checked.
The indication is hexadecimal.
ADDRESS 7010 - KEYBOARD 1 SETTINGS
Keyboard 1
Settings
At this address the Keyboard 1 parameters are assigned.
The digital buttons 1 to 6 are used for programming. Pressing them each time will alternatively change
the status of the parameter - active / inactive. At the end of the procedure only those parameters, which
correspond to the desired settings, should remain activated on the display.
Note: If a keyboard is attached to neither of the partitions, it can not control the system - arming,
disarming, bypass and etc. The user can only enter the engineer menu and do some settings in the
system.
At the default settings the display will show:
LED

LCD
(1) 2 3 4 5 (6)
1. PART A
The keyboard is attached to Partition А. The User can perform actions in Partition A*.
2. PART B
The keyboard is attached to Partition В. The User can perform actions in Partition B**.
3. Chime
disable
This is local setting for the keyboard. When the attribute is assigned
the keyboard will not produce the "Chime" sound signal.
Attribute
OFF
ON
4. Keypad
zone
5. Silent
Panic
With this attribute is assigning the number of the keyboard zone - 1 or
7. With set parameter the keyboard will be zone 7. See also the table
on the right.
With this attribute is assigned, in case of sent PANIC alarm signal from
the keyboard, the siren will not sound.
Keypad
zone
ZONE 1
ZONE 7
Attribute
Disabled
Enabled
6. Zone
Enable
With this attribute the engineer can disable or enable the keyboard
zone.
Attribute
Disabled
Enabled
Indication
LED
LCD


3
(3)
Indication
LED
LCD


4
(4)
Indication
LED
LCD


5
(5)
Indication
LED
LCD


6
(6)
Default settings - PART A, Zone Enable
* User with a personal code with rights to operate in Partition A. User code with rights to operate only with Partition B will
be rejected.
** User with a personal code with rights to operate in Partition B. User code with rights to operate only with Partition A will
be rejected.
48
Installation and Programming Manual - СА62 Alarm Control Panel
ADDRESS 7011 - LEFT ARROW BUTTON OF KEYBOARD 1
"Left arrow"
button of
Keyboard1
At this address the arming mode of the system with the "left arrow" button of the keyboard 1 is assigned.
The digital buttons 1 to 6 are used for programming. Pressing them each time will alternatively change
the status of the parameter - active / inactive.
Only one attribute can be assigned.
1. Full Arm
PART A
Full arming mode for PARTITION А.
2. Stay Arm
PART A
Stay arming mode for PARTITION А - the user is allowed to stay in certain zones in PARTITION A.
3. Stay Arm
Part В
Stay arming mode for PARTITION B - the user is allowed to stay in certain zones in PARTITION B.
4. Inst Arm
Part А
Instant arming mode of PARTITION А.
5. Inst Arm
Part B
Instant arming mode of PARTITION B.
6. Arm
Following
The arming of the partition(s) is with specifying the arming mode type: Full, Stay or Instant.
Example:
With assigning this parameter, the system arming will be as follows:
◄ (left arrow) + 0 - Full Arming Mode
◄ (left arrow) + 1 - Stay Arming Mode
◄ (left arrow) + 2 - Instant Arming Mode
Default settings - Arm Following
ADDRESS 7012 - RIGHT ARROW BUTTON OF KEYBOARD 1
At this address the arming mode of the system with the "right arrow" button of the keyboard 1 is as"Right arrow" signed.
The digital buttons 1 to 6 are used for programming. Pressing them each time will alternatively change
button of
the status of the parameter - active / inactive.
Keyboard1
Only one attribute can be assigned.
1. Full Arm
PART В
Full arming mode for PARTITION В.
2. Stay Arm
PART A
Stay arming mode for PARTITION А - the user is allowed to stay in certain zones in PARTITION A.
3. Stay Arm
Part В
Stay arming mode for PARTITION B - the user is allowed to stay in certain zones in PARTITION B.
4. Inst Arm
Part А
Instant arming mode of PARTITION А.
5. Inst Arm
Part B
Instant arming mode of PARTITION B.
6. Arm
Following
The arming of the partition(s) is with specifying the arming mode type: Full, Stay or Instant.
Example:
With assigning this parameter, the system arming will be as follows:
► (right arrow) + 0 - Full Arming Mode
► (right arrow) + 1 - Stay Arming Mode
► (right arrow) + 2 - Instant Arming Mode
Default settings - Arm Following
Installation and Programming Manual - СА62 Alarm Control Panel
49
ADDRESS 7013 - ARM Button for keyboard 1
ARM Button
Keyboard 1
At this address the function of "ARM" button of the keyboard 1 is assigned.
Note: In the LED62 the button
corresponds to ARM button.
The digital buttons 1, 2 and 6 are used for programming. Pressing them each time will alternatively
change the status of the parameter - active / inactive.
Only one attribute can be assigned.
1. No ARM
The ARM button is disabled for arming the system.
2. Full
ARM All
The ARM button is enabled for Full arming of the partition(s) to which the keyboard is attached. DISARMING the both Partitions with one button (ARM) will function only, when at ADDRESS 7010 both
attributes 1. PART A and 2. PART B are assigned.
6. Arm *
Following
The arming of the partition(s) is with specifying the arming mode type: Full, Stay or Instant.
Example:
With assigning this parameter, the system arming will be as follows:
ARM or
+ 0 - Full Arming Mode
ARM or
+ 1 - Stay Arming Mode
ARM or
+ 2 - Instant Arming Mode
* NOTE: The Arm Following procedure is applied to user codes attached only to one of the Partitions.
Default settings - Arm Following
ADDRESSES 7020 ... 7023 – KEYBOARD 2 PROGRAMMING
The programming is the same as at ADDRESSES 7010 - 7013, as the programming is for Keyboard 2.
Default settings: Configuration - Partition А, Zone Enable; Left arrow - ARM Following; Right arrow - ARM
Following; ARM button - ARM Following
ADDRESSES 7030 ... 7033 – KEYBOARD 3 PROGRAMMING
The programming is the same as at ADDRESSES 7010 - 7013, as the programming is for Keyboard 3.
Default settings: Configuration - Partition А, Zone Enable; Left arrow - ARM Following; Right arrow - ARM
Following; ARM button - ARM Following
ADDRESSES 7040 ... 7043 – KEYBOARD 4 PROGRAMMING
The programming is the same as at ADDRESSES 7010 - 7013, as the programming is for Keyboard 4.
Default settings: Configuration - Partition А, Zone Enable; Left arrow - ARM Following; Right arrow - ARM
Following; ARM button - ARM Following
ADDRESSES 7050 ... 7053 – KEYBOARD 5 PROGRAMMING
The programming is the same as at ADDRESSES 7010 - 7013, as the programming is for Keyboard 5.
Default settings: Configuration - Partition А, Zone Enable; Left arrow - ARM Following; Right arrow - ARM
Following; ARM button - ARM Following
ADDRESSES 7060 ... 7063 – KEYBOARD 6 PROGRAMMING
The programming is the same as at ADDRESSES 7010 - 7013, as the programming is for Keyboard 6.
Default settings: Configuration - Partition А, Zone Enable; Left arrow - ARM Following; Right arrow - ARM
Following; ARM button - ARM Following
ADDRESSES 7070 ... 7073 – KEYBOARD 7 PROGRAMMING
The programming is the same as at ADDRESSES 7010 - 7013, as the programming is for Keyboard 7.
Default settings: Configuration - Partition А, Zone Enable; Left arrow - ARM Following; Right arrow - ARM
Following; ARM button - ARM Following
ADDRESSES 7080 ... 7083 – KEYBOARD 8 PROGRAMMING
The programming is the same as at ADDRESSES 7010 - 7013, as the programming is for Keyboard 8.
Default settings: Configuration - Partition А, Zone Enable; Left arrow - ARM Following; Right arrow - ARM
Following; ARM button - ARM Following
50
Installation and Programming Manual - СА62 Alarm Control Panel
At ADDRESSES 71хх are programmed the parameters and the attributes for the connected to the system proximity card
readers. Up to 4 readers can be connected in the system.
ADDRESS 7100 - Proxi READER 1 SETTINGS
Proxi 1
Settings
At this address the parameters of Proxi Reader 1 are assigned.
Pressing them each time will alternatively change the status of the parameter - active / inactive.
Note: Every Proxi Reader can be attached to the both partitions in the system. In this case, if a proxi
card with user rights for the both partitions in the system is approached to the reader - the both partitions will be armed or disarmed according their current status. If the one partition is armed and the
other is disarmed, then approaching the same user card will disarm the armed partition. The next approaching of the user card will arm the both partitions again.
At the default settings the display will show:
LED

LCD
(1) 2 3 4 5 6
1. PART A
The Proxi Reader is attached to Partition А.
Note: When the Proxi Reader is attached to Partition A only, then with approaching a user card with the
respective rights, if the Partition A is disarmed - it arms, if the Partition A is armed - it disarms.
2. PART B
The Proxi Reader is attached to Partition В.
Note: When the Proxi Reader is attached to Partition B only, then with approaching a user card with
the respective rights, if the Partition A is disarmed - it arms, if the Partition B is armed - it disarms.
Default settings - PART A
ADDRESS 7110 – Proxi READER 2 SETTINGS
The programming is the same as ADDRESS 7100, as the programming is for Proxi Reader 2.
Default settings: PART А
ADDRESS 7120 – Proxi READER 3 SETTINGS
The programming is the same as ADDRESS 7100, as the programming is for Proxi Reader 3.
Default settings: PART А
ADDRESS 7130 – Proxi READER 4 SETTINGS
The programming is the same as ADDRESS 7100, as the programming is for Proxi Reader 4.
Default settings: PART А
TABLE 1 continues on 52 
Set date
Chime Enable/ Disable
0031
0040
LED 3
1. Relay
1. Ring
1. Dial tone
PGM1
ZONE 1
LED 4
LED 5
Part B
NO - LEDs off
2. BATT LOW
NO - LEDs off
NO - LEDs off
Part B
NO - LEDs off
NO - LEDs off
2. Dial tone
2. Call back
2. Dialling
PGM2
ZONE 2
Digit 2
YES - LEDs on
Digit 3
Digit 4
LED 6
4. NO TEL
LINE
6. TAMPER
ZONE 5
5. Wait kiss-off
4. High freq.
4. Receive
5. DTMF “3”
5. Transmit
Viewing the LOG memory.
4. Send data
PGM4
Testing the keyboards indication.
ZONE 4
6. End
6. All sent
ZONE 6
YES - LEDs on
Date setting (DD.MM). Default at RESET → 01.01.
Clock setting (HH:MM). Default at RESET → 00:00.
3. Low freq.
3. Currier
3. Wait HS
PGM3
ZONE 3
YES - LEDs on
5. COMM
ERROR
Audible TAMPER enabled in DISARM - LEDs on
Number 00 to 99 min → 00 min.
3. FUSE
BLOWN
YES - LEDs on
YES - LEDs on
Press the keys from 1 to 6 consequently and confirm by ENTER
Press the keys from 1 to 6 consequently and confirm by ENTER
Digit 1
0. Engineer Parameters and Common Settings
LED 2
Audible TAMPER disabled in DISARM - LEDs off
Part A
1. AC LOST
Part A
LED 1
DEFAULT CONFIGURATION 0
- Default settings at hardware or software RESET. The default CONFIGURATION 0 is set by default.
Comm. HW test
UDL / Direct UDL
0025
Set clock
Display LOG
0024
0026
Comm. Display
0023
0030
Outputs test
0022
Bell on TAMPER
0017
Walk test
Bell on Tel Line Fault
0016
Keypad test
Line fault delay
0015
0020
AC delay 30 minutes
0014
0021
Trouble mask
0013
Quick ARM enable
0010
Enable ambush code
Partial reset
0003
Enable keypad block
Default settings
0002
0011
Reset enable
0001
0012
Engineer code (7777)
MENU
0000
ADDRESS
table 1: Engineer Menu - DEFAULT CONFIGURATION 0, 1, 2 and 3
Follow the next sequence when program the system:
All parameters, attrubutes, codes and values in the
system are program in one and same way.
SUPPLEMENT A - Default programming tables
NO
Steps 1- 5
Steps 1- 6
Steps 1- 6
PGM 1 - 4
ZONE 1- 6
Enabled
15 min
NO
1, 2, 3, 4,
5, 6
NO
NO
A and B
YES
7777
DEFAULT
CONFIG. 1
NO
Steps 1- 5
Steps 1- 6
Steps 1- 6
PGM 1 - 4
ZONE 1- 6
Enabled
15 min
NO
1, 2, 3, 4,
5, 6
NO
NO
A and B
YES
7777
DEFAULT
CONFIG. 2
NO
Steps 1- 5
Steps 1- 6
Steps 1- 6
PGM 1 - 4
ZONE 1- 6
Enabled
15 min
NO
1, 2, 3, 4,
5, 6
NO
NO
A and B
YES
7777
DEFAULT
CONFIG. 3
SUPPLEMENTS - СА62 Alarm Control Panel
51
User code 10 (- - - -)
User code 11 (- - - -)
User code 12 (- - - -)
User code 13 (- - - -)
User code 14 (- - - -)
User code 15 (- - - -)
User code 16 (- - - -)
User code 17 (- - - -)
User code 18 (- - - -)
User code 19 (- - - -)
User code 20 (- - - -)
1100
1110
1120
1130
1140
1150
1160
1170
1180
1190
1200
DISARM
DISARM
DISARM
DISARM
DISARM
DISARM
DISARM
DISARM
DISARM
DISARM
DISARM
DISARM
DISARM
DISARM
DISARM
DISARM
LED 3
LED 4
DEFAULT CONFIGURATION 0
LED 5
LED 6
DEFAULT
CONFIG. 1
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
STAY ARM
4 digits - LEDs off
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
BYPASS
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
PROGRAM
Part A
Part A
Part A
Part A
Part A
Part 1
Part A
Part A
Part A
Part A
Part A
Part A
Part A
Part A
Part A
Part A
Part A
Part A
Part A
Part A
Part A
Part A
Part A
Part A
6 digits - LEDs on
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
Part B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), В
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(1111), А
4 digits
DEFAULT
CONFIG. 2
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), B
(- - - -), В
(- - - -), В
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(1111), А
4 digits
DEFAULT
CONFIG. 3
(- - - -)
(- - - -)
(- - - -)
(- - - -)
(- - - -), В
(- - - -), А
(- - - -)
(- - - -), В
(- - - -), А
(0000); А, В (0000); А, В (0000); А, В
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(- - - -), А
(1111), А
4 digits
Enter the number of the desired default configuration from 0 to 3. Setting at RESET → 0.
1. User and Manager Codes Programming
LED 2
(- - - -) means, that there is no default programmed code for this user
Manager 3 (- - - -)
User code 9 (- - - -)
1090
1240
User code 8 (- - - -)
1080
Manager 2 (- - - -)
User code 7 (- - - -)
1070
1230
User code 6 (- - - -)
1060
Manager 1 (- - - -)
User code 5 (- - - -)
1050
Chief Manager (0000)
User code 4 (- - - -)
1040
1220
DISARM
User code 3 (- - - -)
1030
1210
DISARM
User code 2 (- - - -)
1020
DISARM
User code 1 (- - - -)
1010
DISARM
Default configurations
Code digits
LED 1
1000
MENU
1001
ADDRESS
52
SUPPLEMENTS - СА62 Alarm Control Panel
TABLE 1 continues 
ZONE 4 Hardware
Zone 4 counter
Zone 4 attributes 3
2043
2047
Zone 4 attributes 2
2042
2046
Zone 4 attributes 1
2041
Zone 4 attributes AUX
Zone 4 type
2040
ZONE 4 Attachment
ZONE 3 Hardware
2036
2044
ZONE 3 Attachment
2035
2045
Zone 3 attributes 3
Zone 3 attributes AUX
2033
Zone 3 attributes 2
2032
2034
Zone 3 type
Zone 3 attributes 1
ZONE 2 Hardware
2026
2030
ZONE 2 Attachment
2025
2031
Zone 2 attributes AUX
2024
Zone 2 attributes 1
2021
Zone 2 attributes 2
Zone 2 type
2020
Zone 2 attributes 3
ZONE 1 Attachment
2015
2022
Zone 1 attributes AUX
2014
2023
Zone 1 attributes 2
Zone 1 attributes 1
2011
Zone 1 attributes 3
Zone 1 type
2010
2012
Enable Instant
2001
2013
AutoBypass counter
2000
YES - LEDs on
2. Full / Stay
2. Silent
2. BYPASS
4. FORCE
3. Disarm Enable
3. VideoOnArmed 4. Write to LOG
3. STAY
5. Chime
5. DOUBLE
6. E/E FINAL
2. Full / Stay
2. Silent
2. BYPASS
4. FORCE
3. Disarm Enable
3. VideoOnArmed 4. Write to LOG
3. STAY
5. Chime
5. DOUBLE
Choose the type of ZONE 2 (0 - 9). Setting at RESET → 0. UNUSED
Part B
6. E/E FINAL
Part B
3.Power-up Delay
4.DOUBLING
2. Full / Stay
2. Silent
2. BYPASS
4. FORCE
3. Disarm Enable
3. VideoOnArmed 4. Write to LOG
3. STAY
5. Chime
5. DOUBLE
Choose the type of ZONE 3 (0 - 9). Setting at RESET → 0. UNUSED
2. Fast/ Regular
6. E/E FINAL
3.Power-up Delay
4.DOUBLING
2. Full / Stay
2. Silent
2. BYPASS
4. FORCE
3. Disarm Enable
3. VideoOnArmed 4. Write to LOG
3. STAY
5. Chime
5. DOUBLE
Choose the type of ZONE 4 (0 - 9). Setting at RESET → 0. UNUSED
2. Fast/ Regular
Part B
6. E/E FINAL
TABLE 1 continues 
1. EOL
Part A
3.Power-up Delay
4.DOUBLING
Enter a number from 0 to 9. Setting at RESET → 0
2. Fast/ Regular
Part B
Choose the Attribute AUX for ZONE 4 (00 - 11).Setting at RESET → 00. 24h Burglary
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
1. EOL
Part A
Choose the Attribute AUX for ZONE 3 (00 - 11).Setting at RESET → 00. 24h Burglary
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
1. EOL
Part A
Choose the Attribute AUX for ZONE 2 (00 - 11).Setting at RESET → 00. 24h Burglary
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
Part A
00. 24h Burglary \ 01. Battery Low \ 02. Gas detector \ 03. Water Leakage \ 04. AC Lost\
05. GSM Link Trouble \ 06. Refrigeration \ 07. Loss of heat \ 08. Foil Break \
09. Low Bottled gas level \ 10. High temperature \ 11. Low temperature
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
0. UNUSED \ 1. Entry-Exit \ 2. FOLLOW \ 3. INSTANT \ 4. FIRE \ 5. PANIC \ 6. TAMPER \
7. MEDICAL \ 8. KEY-SWITCH \ 9. AUXILIARY
NO - LEDs off
Enter a number from 0 to 9. Setting at RESET → 6
2. Programming of Zones
Part A
00. 24h
Burglary
3.Disarm En.
2. BYPASS
1. EntryExit
NO
6
Part A and
В
00. 24h
Burglary
3.Disarm En.
2. BYPASS
1. EntryExit
NO
6
Part A
00
3.Disarm En.
2 and 3
Part A and В
00
3.Disarm En.
2 and 3
0
Part A
00
3.Disarm En.
2 and 3
3. INSTANT
Part A
00
3.Disarm En.
2 and 3
0
Part В
00
3.Disarm En.
2 and 3
1. EntryExit
Part A
00
3.Disarm En.
2 and 3
0
Part A
00
3.Disarm En.
2 and 3
3. INSTANT
Part A
00
3.Disarm En.
2 and 3
3. INSTANT 3. INSTANT 3. INSTANT
Part A
00
3.Disarm En.
2 and 3
2. FOLLOW 2. FOLLOW 2. FOLLOW
Part A
00. 24h
Burglary
3.Disarm En.
2. BYPASS
1. EntryExit
NO
6
SUPPLEMENTS - СА62 Alarm Control Panel
53
Zone 9 attributes 1
Zone 9 attributes 2
Zone 9 attributes 3
Zone 9 attributes AUX
ZONE 9 Attachment
2091
2092
2093
2094
2095
Zone 8 attributes 3
2083
Zone 9 type
Zone 8 attributes 2
2082
2090
Zone 8 attributes 1
2081
Zone 8 attributes AUX
Zone 8 type
2080
ZONE 8 Attachment
ZONE 7 Attachment
2075
2084
Zone 7 attributes AUX
2074
2085
Zone 7 attributes 2
Zone 7 attributes 3
Zone 7 attributes 1
2071
2072
Zone 7 type
2070
2073
ZONE 6 Hardware
2066
Zone 6 attributes 2
2062
ZONE 6 Attachment
Zone 6 attributes 1
2061
2065
Zone 6 type
2060
Zone 6 attributes 3
ZONE 5 Hardware
2056
Zone 6 attributes AUX
ZONE 5 Attachment
2055
2063
Zone 5 attributes AUX
2054
2064
Zone 5 attributes 2
Zone 5 attributes 3
2052
Zone 5 attributes 1
2051
2053
Zone 5 type
MENU
2050
ADDRESS
LED 3
LED 4
LED 5
2. Full / Stay
2. Silent
2. BYPASS
4. FORCE
3. Disarm Enable
3. VideoOnArmed 4. Write to LOG
3. STAY
5. Chime
5. DOUBLE
Choose the type of ZONE 5 (0 - 9). Setting at RESET → 0. UNUSED
LED 2
6. E/E FINAL
LED 6
Part B
3.Power-up Delay
4.DOUBLING
2. Full / Stay
2. Silent
2. BYPASS
4. FORCE
3. Disarm Enable
3. VideoOnArmed 4. Write to LOG
3. STAY
5. Chime
5. DOUBLE
Choose the type of ZONE 6 (0 - 9). Setting at RESET → 0. UNUSED
2. Fast/ Regular
6. E/E FINAL
3.Power-up Delay
4.DOUBLING
2. Full / Stay
2. Silent
2. BYPASS
4. FORCE
3. Disarm Enable
3. VideoOnArmed 4. Write to LOG
3. STAY
5. Chime
5. DOUBLE
Choose the type of ZONE 7 (0 - 9). Setting at RESET → 0. UNUSED
2. Fast/ Regular
Part B
6. E/E FINAL
Part B
2. Full / Stay
2. Silent
2. BYPASS
4. FORCE
3. Disarm Enable
3. VideoOnArmed 4. Write to LOG
3. STAY
5. Chime
5. DOUBLE
Choose the type of ZONE 8 (0 - 9). Setting at RESET → 0. UNUSED
6. E/E FINAL
2. Full / Stay
2. Silent
2. BYPASS
4. FORCE
3. Disarm Enable
3. VideoOnArmed 4. Write to LOG
3. STAY
5. Chime
5. DOUBLE
Choose the type of ZONE 9 (0 - 9). Setting at RESET → 0. UNUSED
Part B
6. E/E FINAL
Part A
Part B
Choose the Attribute AUX for ZONE 9 (00 - 11).Setting at RESET → 00. 24h Burglary
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
Part A
Choose the Attribute AUX for ZONE 8 (00 - 11).Setting at RESET → 00. 24h Burglary
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
Part A
Choose the Attribute AUX for ZONE 7 (00 - 11).Setting at RESET → 00. 24h Burglary
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
1. EOL
Part A
Choose the Attribute AUX for ZONE 6 (00 - 11).Setting at RESET → 00. 24h Burglary
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
1. EOL
Part A
Choose the Attribute AUX for ZONE 5 (00 - 11).Setting at RESET → 00. 24h Burglary
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
LED 1
DEFAULT CONFIGURATION 0
DEFAULT
CONFIG. 3
Part B
00
3.Disarm En.
2
Part В
00
3.Disarm En.
2 and 3
Part B
00
3.Disarm En.
2
3. INSTANT 3. INSTANT
Part В
00
3.Disarm En.
2 and 3
2. FOLLOW 3. INSTANT
DEFAULT
CONFIG. 2
Part A
00
3.Disarm En.
2
Part A
00
3.Disarm En.
2
Part A
00
3.Disarm En.
2
Part A
00
3.Disarm En.
2
Part A
00
3.Disarm En.
2
Part A
00
3.Disarm En.
2
Part A
00
3.Disarm En.
2
0. UNUSED 0. UNUSED 0. UNUSED
Part A
00
3.Disarm En.
2
0. UNUSED 0. UNUSED 0. UNUSED
Part A
00
3.Disarm En.
2
0. UNUSED 0. UNUSED 0. UNUSED
Part A
00
3.Disarm En.
6. TAMPER
Part A
00
3.Disarm En.
2
5. PANIC
DEFAULT
CONFIG. 1
54
SUPPLEMENTS - СА62 Alarm Control Panel
TABLE 1 continues 
1. MEDICAL
Zone 12 attributes 1
Zone 12 attributes 2
Zone 12 attributes 3
Zone 12 attributes AUX
ZONE 12 Attachment
PGM 1 Parameters 1
PGM 1 Parameters 2
PGM 1 Attachment
PGM 1 Extension
2121
2122
2123
2124
2125
3010
3011
3012
3013
PGM 1 Extension Х2
PGM 1 Extension Х3
PGM 1 Extension Х4
PGM 1 Device ID
PGM 1 Device ID
3015
3016
3017
3018
3019
PGM 1 Extension Х1
1. ALARM
Zone 12 type
2120
3. Disarm Enable
5. Chime
5. DOUBLE
6. E/E FINAL
Part B
2. Full / Stay
2. Silent
2. BYPASS
4. FORCE
3. Disarm Enable
3. VideoOnArmed 4. Write to LOG
3. STAY
5. Chime
5. DOUBLE
Choose the type of ZONE 11 (0 - 9). Setting at RESET → 0. UNUSED
6. E/E FINAL
2. Full / Stay
2. Silent
2. BYPASS
4. FORCE
3. Disarm Enable
3. VideoOnArmed 4. Write to LOG
3. STAY
5. Chime
5. DOUBLE
Choose the type of ZONE 12 (0 - 9). Setting at RESET → 0. UNUSED
Part B
6. E/E FINAL
Part B
2. PS/BYPASS
2. PANIC
3. SIREN
3. TAMPER
4. TECH.TRBL
4. FIRE
5. PULSE/LATCH
5. FIRE RESET
3. PGM and SIREN Outputs Programming
Part B
6. POLARITY
6. ON / OFF
Keyboard 7
Keyboard 1
Code 19
Code 13
Code/ Zone 7
Code/ Zone 1
Keyboard 8
Keyboard 2
Code 20
Code 14
Code/ Zone 8
Code/ Zone 2
Proxi Reader 1
Keyboard 3
Manager
Code 15
Code/ Zone 9
Code/ Zone 3
Proxi Reader 2
Keyboard 4
Manager 1
Code 16
Code/ Zone 10
Code/ Zone 4
Proxi Reader 3
Keyboard 5
Manager 2
Code 17
Code/ Zone 11
Code/ Zone 5
Proxi Reader 4
Keyboard 6
Manager 3
Code 18
Code/ Zone 12
Code/ Zone 6
00. No Extension \ 01. Battery Trouble \ 02. Blown Fuse \ 03. Tel. Line Trouble \
04. AC Loss - Main board \ 05. AC Loss - Zone \ 06. Keypad Alarm \ 07. Keypad Fire Alarm\ 08. Keypad
Panic Alarm \ 09. Duress Alarm \ 10. Chime \ 11. Auxiliary Alarm \
12. Battery Trouble \ 13. Wireless Transmitter Supervision Loss \
14. Wireless Transmitter Battery Low \ 15. Auto-ARM \ 16. Vide-On-Armed \
17. Zone Violation \ 18. Code Used Signalling \ 19. Proximity Card Used Signalling
Part A
Part A
Choose the Attribute AUX for ZONE 12 (00 - 11).Setting at RESET → 00. 24h Burglary
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
Part A
Zone 11 attributes AUX
ZONE 11 Attachment
3014
4. FORCE
3. VideoOnArmed 4. Write to LOG
3. STAY
Choose the Attribute AUX for ZONE 11 (00 - 11).Setting at RESET → 00. 24h Burglary
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
Part A
2114
Zone 11 attributes 3
2113
2. Full / Stay
2. Silent
2. BYPASS
Choose the type of ZONE 10 (0 - 9). Setting at RESET → 0. UNUSED
Choose the Attribute AUX for ZONE 10 (00 - 11).Setting at RESET → 00. 24h Burglary
1. Pulse / Latch
1. Bell delay
1. AUTOBYPASS
2115
Zone 11 attributes 2
Zone 11 type
2110
Zone 11 attributes 1
ZONE 10 Attachment
2105
2111
Zone 10 attributes AUX
2104
2112
Zone10 attributes 2
Zone 10 attributes 3
2102
Zone10 attributes 1
2101
2103
Zone 10 type
2100
Part A
00
3.Disarm En.
2
Part A
00
3.Disarm En.
2
Part A
00
3.Disarm En.
2
Part A
00
3.Disarm En.
2
00
Part A
6
6
Part A
00
3.Disarm En.
2
00
Part A
6
6
Part A
00
3.Disarm En.
2
00
Part A
6
6
Part A
00
3.Disarm En.
2
0. UNUSED 0. UNUSED 0. UNUSED
Part A
00
3.Disarm En.
2
0. UNUSED 0. UNUSED 0. UNUSED
Part A
00
3.Disarm En.
2
0. UNUSED 0. UNUSED 0. UNUSED
SUPPLEMENTS - СА62 Alarm Control Panel
55
TABLE 1 continues 
PGM 3 Extension Х2
PGM 3 Extension Х3
PGM 3 Extension Х4
PGM 3 Device ID
3035
3036
3037
3038
SIREN (PGM4) Extension Х1
SIREN (PGM4) Extension Х2
SIREN (PGM4) Extension Х3
SIREN (PGM4) Extension Х4
SIREN (PGM4) Device ID
SIREN (PGM4) Device ID
3044
3046
3047
3048
3049
SIREN (PGM4) Extension
3043
3045
SIREN (PGM4) Parameters 2
SIREN (PGM4) Attachment
3041
3042
PGM 3 Device ID
PGM 3 Extension Х1
3034
SIREN (PGM4) Parameters 1
PGM 3 Extension
3033
3039
PGM 3 Attachment
3032
3040
PGM 3 Parameters 1
PGM 3 Parameters 2
PGM 2 Device ID
3029
3030
PGM 2 Device ID
3028
3031
PGM 2 Extension Х4
3027
PGM 2 Extension Х1
3024
PGM 2 Extension Х2
PGM 2 Extension
3023
PGM 2 Extension Х3
PGM 2 Attachment
3022
3025
PGM 2 Parameters 2
3021
3026
PGM 2 Parameters 1
MENU
3020
ADDRESS
Part B
2. PS/BYPASS
2. PANIC
LED 2
3. SIREN
3. TAMPER
LED 3
4. TECH.TRBL
4. FIRE
LED 4
5. PULSE/LATCH
5. FIRE RESET
LED 5
6. POLARITY
6. ON / OFF
LED 6
Part B
2. PS/BYPASS
2. PANIC
Keyboard 8
Keyboard 2
Code 20
Code 14
Code/ Zone 8
Code/ Zone 2
3. SIREN
3. TAMPER
Proxi Reader 1
Keyboard 3
Manager
Code 15
Code/ Zone 9
Code/ Zone 3
4. TECH.TRBL
4. FIRE
Proxi Reader 2
Keyboard 4
Manager 1
Code 16
Code/ Zone 10
Code/ Zone 4
5. PULSE/LATCH
5. FIRE RESET
Proxi Reader 3
Keyboard 5
Manager 2
Code 17
Code/ Zone 11
Code/ Zone 5
6. POLARITY
6. ON / OFF
Proxi Reader 4
Keyboard 6
Manager 3
Code 18
Code/ Zone 12
Code/ Zone 6
Part B
2. PS/BYPASS
2. PANIC
Keyboard 8
Keyboard 2
Code 20
Code 14
Code/ Zone 8
Code/ Zone 2
3. SIREN
3. TAMPER
Proxi Reader 1
Keyboard 3
Manager
Code 15
Code/ Zone 9
Code/ Zone 3
4. TECH.TRBL
4. FIRE
Proxi Reader 2
Keyboard 4
Manager 1
Code 16
Code/ Zone 10
Code/ Zone 4
5. PULSE/LATCH
5. FIRE RESET
Proxi Reader 3
Keyboard 5
Manager 2
Code 17
Code/ Zone 11
Code/ Zone 5
6. POLARITY
6. ON / OFF
Proxi Reader 4
Keyboard 6
Manager 3
Code 18
Code/ Zone 12
Code/ Zone 6
Keyboard 7
Keyboard 1
Code 19
Code 13
Code/ Zone 7
Code/ Zone 1
Keyboard 8
Keyboard 2
Code 20
Code 14
Code/ Zone 8
Code/ Zone 2
Proxi Reader 1
Keyboard 3
Manager
Code 15
Code/ Zone 9
Code/ Zone 3
Proxi Reader 2
Keyboard 4
Manager 1
Code 16
Code/ Zone 10
Code/ Zone 4
Proxi Reader 3
Keyboard 5
Manager 2
Code 17
Code/ Zone 11
Code/ Zone 5
Proxi Reader 4
Keyboard 6
Manager 3
Code 18
Code/ Zone 12
Code/ Zone 6
Choose an Extension number for PGM 4 (00 - 19). Setting at RESET → 00. No Extension
Part A
1. MEDICAL
1. ALARM
Keyboard 7
Keyboard 1
Code 19
Code 13
Code/ Zone 7
Code/ Zone 1
Choose an Extension number for PGM 3 (00 - 19). Setting at RESET → 00. No Extension
Part A
1. MEDICAL
1. ALARM
Keyboard 7
Keyboard 1
Code 19
Code 13
Code/ Zone 7
Code/ Zone 1
Choose an Extension number for PGM 2 (00 - 19). Setting at RESET → 00. No Extension
Part A
1. MEDICAL
1. ALARM
LED 1
DEFAULT CONFIGURATION 0
00
Part A
3, 6
00
Part A
4, 6
00
Part A
6
1, 3
DEFAULT
CONFIG. 1
00
3, 6
00
Part A
4, 6
00
Part A
6
1, 3
DEFAULT
CONFIG. 2
00
3, 6
00
Part A
4, 6
00
Part A
6
1, 3
DEFAULT
CONFIG. 3
56
SUPPLEMENTS - СА62 Alarm Control Panel
TABLE 1 continues 
Bell time Part A
Bell delay Part A
Auto ARM time Part A
4012
4013
4014
Exit time Part B
Entry time Part B
Bell time Part B
Bell delay Part B
Auto ARM time Part B
4020
4021
4022
4023
4024
00:00
Enter time (HH:MM) for Automatic ARM of Part B. Settings at RESET → 00:00.
2. Sqwk DISARM 3. Auto-Arm Enbl 4. Arm Full / Stay
Telephone number 2
Comm. Protocol 2
Messages
6020
6021
6022
6. TROUBLE
from 1 to 6
TABLE 1 continues 
1. ALARM
2. PANIC
3. FIRE
4. ON/OFF+BPS
5. MEDICAL
6. TROUBLE
1
5. MEDICAL
Enter communication protocol number (1 - Contact ID; 2-SIA). Settings at RESET → 1-Contact ID.
4. ON/OFF+BPS
no tel.
number
3. FIRE
Max. phone number length - 16 symbols, pulse dialing=ARM+0, DTMF dialing=ARM+1,
pause=ARM+2, Enabling "Dial tone detector"=ARM+3, Disabling "Dial tone detector" =ARM=4, clear
number=ARM+5. Default settings at RESET -> no number.
2. PANIC
1
1. ALARM
Enter communication protocol number (1 - Contact ID; 2-SIA). Settings at RESET → 1-Contact ID.
Comm. Protocol 1
Messages
6011
6012
9999
Valid Code
00:00
0
3
15
45
9999
Valid Code
00:00
0
3
15
45
9999
Valid Code
00:00
0
3
15
45
9999
Valid Code
00:00
0
3
15
45
1
no tel.
number
from 1 to 6
1
no tel.
number
00:05
24
1
no tel.
number
from 1 to 6
1
no tel.
number
00:05
24
0, 4 attempts 0, 4 attempts 0, 4 attempts
9999
24
From 0 to 9 attempts. Settings at RESET -> 0, meaning 4 attempts
6. PROGRAMMING OF COMMUNICATION DEVICES
Communication account for Part B - 4 digits (from 0 to 9 + symbols А to F).
Settings at RESET → FFFF.
Enter the duration of the test period - from 00 to 99 hours. Settings at RESET → 24.
1. Sqwk ARM
no tel.
number
6003
0
0-99 min. Settings at RESET → 0.
Telephone number 1
Test start time
6002
6010
Test period
6001
3
0-99 min. Settings at RESET → 3.
Valid Code
15
Enter Entry time for Part B (0-99 sec). Settings at RESET → 15.
Bell Time at ADDRESS 4022 LEDs on
45
Enter Exit time for Part B (0-99 sec). Settings at RESET → 45.
Until a valid user code LEDs off
9999
2. Sqwk DISARM 3. Auto-Arm Enbl 4. Arm Full / Stay
Communication account for Part A - 4 digits (from 0 to 9 + symbols А to F).
Settings at RESET → FFFF.
1. Sqwk ARM
00:05
Communication attempts
4027
00:00
Enter time (HH:MM) for Automatic ARM of Part A. Settings at RESET → 00:00.
Enter the time for starting test period (HH:ММ). Settings at RESET → 00:05.
Communication account
Part B
0
0-99 min. Settings at → 0.
Valid Code
3
0-99 min. Settings at → 3.
Bell Time at ADDRESS 4022 LEDs on
15
Enter Entry time for Part A (0-99 sec). Settings at RESET → 15.
Until a valid user code LEDs off
45
Enter Exit time for Part A (0-99 sec). Settings at RESET → 45.
Max. phone number length - 16 symbols, pulse dialing=ARM+0, DTMF dialing=ARM+1,
pause=ARM+2, Enabling "Dial tone detector"=ARM+3, Disabling "Dial tone detector" =ARM=4, clear
number=ARM+5. Default settings at RESET -> no number.
ATTRIBUTES Part B
4026
FIRE Duration Part B
Communication account
Part A
4017
4025
ATTRIBUTES Part A
4016
FIRE Duration Part A
Entry time Part A
4011
4015
Exit time Part A
4010
4. PARTITIONS Programming
SUPPLEMENTS - СА62 Alarm Control Panel
57
Events VD60
Telephone number for
Up / Download (UDL)
PC ID number for UDL
Panel ID number for UDL
Call back
Number of rings
Answering machine
Keyboard address
Keyboard 1 Settings
Keyboard 1 left arrow
Keyboard 1 right arrow
Keyboard 1 ARM Button
Keyboard 2 Settings
Keyboard 2 left arrow
Keyboard 2 right arrow
Keyboard 2 ARM Button
6035
6900
6901
6902
6903
6904
6905
7000
7010
7011
7012
7013
7020
7021
7022
7023
TABLE 1 continues 
2. Stay ARM
Part A
1. Full ARM
Part B
2. Full ARM all
2. Stay ARM
Part A
1. Full ARM
Part A
1. NO ARM
2. Part B
1. Part A
2. Full ARM all
2. Stay ARM
Part A
1. Full ARM
Part B
1. NO ARM
2. Part B
2. Stay ARM
Part A
1. Part A
1. Full ARM
Part A
4. Instant ARM
Part A
4. Instant ARM
Part A
3. Stay ARM
Part B
3. Stay ARM
Part B
4. Instant ARM
Part A
4. Instant ARM
Part A
3. Chime disable 4. Keypad zone
3. Stay ARM
Part B
3. Stay ARM
Part B
3. Chime disable 4. Keypad zone
5. Instant ARM
Part B
5. Instant ARM
Part B
5. Silent panic
5. Instant ARM
Part B
5. Instant ARM
Part B
5. Silent panic
7
6
6
6. ARM
Following
6
6. ARM
Following
6. ARM
Following
1, 6
6
6. ARM
Following
6. Zone enable
6
6
1, 6
NO
6. ARM
Following
6. ARM
Following
6. Zone enable
Display on each keyboard its address as configured with its jumpers.
7. PROGRAMMING OF PERIPHERAL DEVICES
YES - LEDs on
Enter number of rings from 1 to 9. Settings at RESET -> 7.
NO - LEDs off
NO
1234
4 Digits (from 0 to 9). Settings at RESET → 1234.
YES - LEDs on
1234
4 Digits (from 0 to 9). Settings at RESET → 1234.
NO - LEDs off
no tel.
number
Max. phone number length - 16 symbols, pulse dialing=ARM+0, DTMF dialing=ARM+1,
pause=ARM+2, Enabling "Dial tone detector"=ARM+3, Disabling "Dial tone detector" =ARM=4, clear
number=ARM+5. Default settings at RESET -> no number.
1
no tel.
number
Max. phone number length - 16 symbols, pulse dialing=ARM+0, DTMF dialing=ARM+1,
pause=ARM+2, Enabling "Dial tone detector"=ARM+3, Disabling "Dial tone detector" =ARM=4, clear
number=ARM+5. Default settings at RESET -> no number.
Dialer VD60
Telephone number 4
6034
1 - Alarm, Panic, Tamper, Fire, Medical,
АС LOST, ВАТТ LOW
no tel.
number
Max. phone number length - 16 symbols, pulse dialing=ARM+0, DTMF dialing=ARM+1,
pause=ARM+2, Enabling "Dial tone detector"=ARM+3, Disabling "Dial tone detector" =ARM=4, clear
number=ARM+5. Default settings at RESET -> no number.
Dialer VD60
Telephone number 3
6033
0 - Alarm/ TAMPER by zones
no tel.
number
Max. phone number length - 16 symbols, pulse dialing=ARM+0, DTMF dialing=ARM+1,
pause=ARM+2, Enabling "Dial tone detector"=ARM+3, Disabling "Dial tone detector" =ARM=4, clear
number=ARM+5. Default settings at RESET -> no number.
Dialer VD60
Telephone number 2
DEFAULT
CONFIG. 1
6032
LED 6
no tel.
number
LED 5
Dialer VD60
Telephone number 1
LED 4
Records and Playback voice message into voice dialer VD60
LED 3
6031
LED 2
Max. phone number length - 16 symbols, pulse dialing=ARM+0, DTMF dialing=ARM+1,
pause=ARM+2, Enabling "Dial tone detector"=ARM+3, Disabling "Dial tone detector" =ARM=4, clear
number=ARM+5. Default settings at RESET -> no number.
LED 1
DEFAULT CONFIGURATION 0
VD60 Programming
MENU
6030
ADDRESS
6
1
6
2
6
1
1
1, 6
NO
7
NO
1234
1234
no tel.
number
1
no tel.
number
no tel.
number
no tel.
number
no tel.
number
DEFAULT
CONFIG. 2
6
6
6
1, 6
6
1
1
1, 2
NO
7
NO
1234
1234
no tel.
number
1
no tel.
number
no tel.
number
no tel.
number
no tel.
number
DEFAULT
CONFIG. 3
58
SUPPLEMENTS - СА62 Alarm Control Panel
Keyboard 3 Settings
Keyboard 3 left arrow
Keyboard 3 right arrow
Keyboard 3 ARM Button
Keyboard 4 Settings
Keyboard 4 left arrow
Keyboard 4 right arrow
Keyboard 4 ARM Button
Keyboard 5 Settings
Keyboard 5 left arrow
Keyboard 5 right arrow
Keyboard 5 ARM Button
Keyboard 6 Settings
Keyboard 6 left arrow
Keyboard 6 right arrow
Keyboard 6 ARM Button
Keyboard 7 Settings
Keyboard 7 left arrow
Keyboard 7 right arrow
Keyboard 7 ARM Button
Keyboard 8 Settings
Keyboard 8 left arrow
Keyboard 8 right arrow
Keyboard 8 ARM Button
Proxi reader 1 Setting
Proxi reader 2 Setting
Proxi reader 3 Setting
Proxi reader 4 Setting
7030
7031
7032
7033
7040
7041
7042
7043
7050
7051
7052
7053
7060
7061
7062
7063
7070
7071
7072
7073
7080
7081
7082
7083
7100
7110
7120
7130
2. Stay ARM
Part A
1. Full ARM
Part B
2. Stay ARM
Part A
1. Full ARM
Part B
2. Stay ARM
Part A
1. Full ARM
Part B
Part A
Part A
Part A
Part A
Part B
Part B
Part B
Part B
2. Full ARM all
2. Stay ARM
Part A
1. Full ARM
Part B
1. NO ARM
2. Part B
2. Stay ARM
Part A
1. Part A
1. Full ARM
Part A
2. Full ARM all
2. Stay ARM
Part A
1. Full ARM
Part B
1. NO ARM
2. Part B
2. Stay ARM
Part A
1. Part A
1. Full ARM
Part A
2. Full ARM all
2. Stay ARM
Part A
1. Full ARM
Part B
1. NO ARM
2. Part B
2. Stay ARM
Part A
1. Part A
1. Full ARM
Part A
2. Full ARM all
2. Stay ARM
Part A
1. Full ARM
Part A
1. NO ARM
2. Part B
1. Part A
2. Full ARM all
2. Stay ARM
Part A
1. Full ARM
Part A
1. NO ARM
2. Part B
1. Part A
2. Full ARM all
2. Stay ARM
Part A
1. Full ARM
Part A
1. NO ARM
2. Part B
1. Part A
4. Instant ARM
Part A
4. Instant ARM
Part A
4. Instant ARM
Part A
4. Instant ARM
Part A
4. Instant ARM
Part A
4. Instant ARM
Part A
4. Instant ARM
Part A
4. Instant ARM
Part A
4. Instant ARM
Part A
4. Instant ARM
Part A
3. Stay ARM
Part B
3. Stay ARM
Part B
4. Instant ARM
Part A
4. Instant ARM
Part A
3. Chime disable 4. Keypad zone
3. Stay ARM
Part B
3. Stay ARM
Part B
3. Chime disable 4. Keypad zone
3. Stay ARM
Part B
3. Stay ARM
Part B
3. Chime disable 4. Keypad zone
3. Stay ARM
Part B
3. Stay ARM
Part B
3. Chime disable 4. Keypad zone
3. Stay ARM
Part B
3. Stay ARM
Part B
3. Chime disable 4. Keypad zone
3. Stay ARM
Part B
3. Stay ARM
Part B
3. Chime disable 4. Keypad zone
5. Instant ARM
Part B
5. Instant ARM
Part B
5. Silent panic
5. Instant ARM
Part B
5. Instant ARM
Part B
5. Silent panic
5. Instant ARM
Part B
5. Instant ARM
Part B
5. Silent panic
5. Instant ARM
Part B
5. Instant ARM
Part B
5. Silent panic
5. Instant ARM
Part B
5. Instant ARM
Part B
5. Silent panic
5. Instant ARM
Part B
5. Instant ARM
Part B
5. Silent panic
6. ARM Following
6. ARM
Following
6. ARM
Following
6. Zone enable
6. ARM Following
6. ARM
Following
6. ARM
Following
6. Zone enable
6. ARM Following
6. ARM
Following
6. ARM
Following
Part A
Part A
Part A
Part A
6
6
6
1, 6
6
6
6
1, 6
6
6
6
1, 6
6
6. ARM
Following
6. Zone enable
6
6
1, 6
6
6
6
1, 6
6
6
6
1, 6
6. ARM
Following
6. ARM
Following
6. Zone enable
6. ARM Following
6. ARM
Following
6. ARM
Following
6. Zone enable
6. ARM Following
6. ARM
Following
6. ARM
Following
6. Zone enable
Part A
Part A
Part A
Part A
6
6
6
1,6
6
6
6
1,6
6
6
6
1,6
6
6
6
1,6
6
6
6
1,6
6
6
6
1,6
Part A
Part A
Part A
Part A
6
6
6
1, 6
6
6
6
1, 6
6
6
6
1, 6
6
6
6
1, 6
6
6
6
1, 6
6
6
6
1, 6
SUPPLEMENTS - СА62 Alarm Control Panel
59
User code 6 (- - - -)
User code 6 Attributes
Proximity card Register
Proximity card Delete
User code 7 (- - - -)
User code 7 Attributes
060
062
063
070
071
Proximity card Delete
053
061
User code 5 Attributes
User code 5 (- - - -)
050
Proximity card Register
Proximity card Delete
043
051
Proximity card Register
042
052
User code 4 (- - - -)
User code 4 Attributes
040
Proximity card Delete
033
041
User code 3 Attributes
Proximity card Register
031
User code 3 (- - - -)
030
032
Proximity card Register
Proximity card Delete
022
023
User code 2 (- - - -)
User code 2 Attributes
020
021
Proximity card Delete
013
User code 1 (- - - -)
010
User code 1 Attributes
UDL Access Block
009
Proximity card Register
Comm. manual test
002
011
Engineer access
001
012
Remote Access
MENU
000
ADDRESS
2. ARMING
LED 2
LED 3
LED 4
5. View LOG
LED 5
6. Bypass
LED 6
ENABLED
2, 4, 5
DEFAULT
CONFIG. 1
ENABLED
2, 4, 5
DEFAULT
CONFIG. 2
2. STAY ARM
3. BYPASS
4. PROGRAM
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
2. STAY ARM
3. BYPASS
4. PROGRAM
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
2. STAY ARM
3. BYPASS
4. PROGRAM
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
1. DISARM
2. STAY ARM
3. BYPASS
4. PROGRAM
5. Part A
6. Part B
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
1111
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
1111
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
1111
ENABLED
2, 4, 5
DEFAULT
CONFIG. 3
Enter permissible number of valid access codes (ARM / DISARM / BYPASS / PC ID) for UDL and 24 hour period.
Enter number from 00 up to 99. Default settings at RESET - 10 attempts.
With reaching the permissible number of valid access codes, the system will be blocked - there would be no UDL communication.
The UDL communication will be restored at 00.00 h system time.
Sending of test messages to central monitoring station or test message with the voice dialer VD60.
ENABLED - LEDs on
3. Code Access 4. Programming
Disabled - LEDs off
1. DISARMING
LED 1
DEFAULT CONFIGURATION 0
TABLE 2: Manager Menu - DEFAULT CONFIGURATION 0, 1, 2 and 3
SUPPLEMENT A - Default Programming Tables
60
SUPPLEMENTS - СА62 Alarm Control Panel
TABLE 2 continues 
Proximity card Delete
User code 15 (- - - -)
User code 15 Attributes
Proximity card Register
Proximity card Delete
143
150
151
152
153
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
2. STAY ARM
3. BYPASS
4. PROGRAM
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
2. STAY ARM
3. BYPASS
4. PROGRAM
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
1. DISARM
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
Press ENTER button to delete the card.
Put the card close to the proximity reader.
- Default settings at hardware or software RESET. The default CONFIGURATION 0 is set by default.
Proximity card Register
Proximity card Register
Proximity card Delete
132
133
142
User code 13 Attributes
131
User code 14 (- - - -)
User code 13 (- - - -)
130
User code 14 Attributes
Proximity card Delete
123
140
Proximity card Register
122
141
User code 12 (- - - -)
User code 12 Attributes
120
Proximity card Delete
113
121
Proximity card Register
User code 11 (- - - -)
110
User code 11 Attributes
Proximity card Delete
103
111
Proximity card Register
102
112
User code 10 (- - - -)
User code 10 Attributes
100
Proximity card Delete
093
101
User code 9 Attributes
Proximity card Register
091
User code 9 (- - - -)
090
092
Proximity card Register
Proximity card Delete
082
083
User code 8 (- - - -)
User code 8 Attributes
080
Proximity card Delete
073
081
Proximity card Register
072
(- - - -)
1 to 5
(- - - -)
1 to 5
(- - - -)
1 to 5
(- - - -)
1 to 5
(- - - -)
1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
(- - - -)
from 1 to 5
SUPPLEMENTS - СА62 Alarm Control Panel
61
Manager code 1 (0000)
220
Proximity card Delete
Proximity card Delete
213
223
Proximity card Register
212
Manager code 1 Attributes
Manager code Attributes
211
Proximity card Register
Manager code (0000)
210
221
Proximity card Delete
203
222
User code 20 Attributes
Proximity card Register
201
User code 20 (- - - -)
200
202
Proximity card Register
Proximity card Delete
192
193
User code 19 (- - - -)
User code 19 Attributes
190
Proximity card Delete
183
191
User code 18 Attributes
Proximity card Register
181
182
User code 18 (- - - -)
180
User code 17Attributes
171
Proximity card Register
User code 17 (- - - -)
170
Proximity card Delete
Proximity card Delete
163
172
Proximity card Register
162
173
User code 16 (- - - -)
User code 16 Attributes
160
MENU
161
ADDRESS
LED 2
LED 3
LED 4
DEFAULT CONFIGURATION 0
LED 5
LED 6
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
2. STAY ARM
3. BYPASS
4. PROGRAM
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
2. STAY ARM
3. BYPASS
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
4. PROGRAM
2. STAY ARM
3. BYPASS
4. PROGRAM
5. Part A
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
6. Part B
6. Part B
Press ENTER button to delete the card.
Put the card close to the proximity reader.
5. Part A
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
Press ENTER button to delete the card.
Put the card close to the proximity reader.
5. Part A
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
1. DISARM
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
LED 1
(- - - -) means, that there is no default programmed user / manager code combination
(- - - -)
5 and 6
(0000)
1 to 5
(- - - -)
1 to 5
(- - - -)
1 to 5
(- - - -)
1 to 5
(- - - -)
1 to 5
(- - - -)
DEFAULT
CONFIG. 1
5
(- - - -)
5 and 6
(0000)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
DEFAULT
CONFIG. 2
5
(- - - -)
5 and 6
(0000)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
1 to 4 and 6
(- - - -)
DEFAULT
CONFIG. 3
62
SUPPLEMENTS - СА62 Alarm Control Panel
Manager code 3 Attributes
Proximity card Register
Proximity card Delete
Display LOG Memory
CHIME Enable
BYPASS ZONES
Setting the clock
Setting the date
241
242
243
300
400
500
600
601
BYPASS ZONES
3
6. Part B
YES - LEDs on
LOG memory file review.
Press ENTER button to delete the card.
LED 3
LED 4
DEFAULT CONFIGURATION 0
LED 5
LED 6
YES - LEDs on
LOG memory file review.
NO
(1111)
- Default settings at hardware or software RESET. The default CONFIGURATION 0 is set by default.
Note: Table 3 contains the default settings for User programming menu entered with User Code 1.
01:01
00:00
NO
(- - - -)
6
(- - - -)
NO
(1111)
DEFAULT
CONFIG. 2
Press a number of a ZONE which you want to bypass.
Use buttons 1 - 9 and combinations ARM+0 (Zone 10), ARM+1 (Zone 11) and ARM+2 (Zone 12),
NO - LEDs off
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
LED 2
DEFAULT
CONFIG. 1
01:01
Date setting ( DD:MM). Settings at RESET → 01:01.
SUPPLEMENT A - Default Programming Tables
00:00
Clock setting ( HH:MM). Settings at RESET → 00:00.
TABLE 3: User Menu - DEFAULT CONFIGURATION 0, 1, 2 and 3
LED 1
NO
(- - - -)
(- - - -)
Press a number of a ZONE which you want to bypass.
Use buttons 1 - 9 and combinations ARM+0 (Zone 10), ARM+1 (Zone 11) and ARM+2 (Zone 12),
NO - LEDs off
6. Part B
Put the card close to the proximity reader.
5. Part A
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
Press ENTER button to delete the card.
Put the card close to the proximity reader.
5. Part A
Enter 4 or 6 digit code (depends on the settings at ADDRESS 1001 from the Engineering Menu)
(- - - -) means, that there is no default programmed user / manager code combination
Display LOG Memory
CHIME Enable
1
2
Change own code (- - - -)
0
MENU
Manager code 3 (0000)
240
ADDRESS
Proximity card Register
Proximity card Delete
232
Manager code 2 Attributes
231
233
Manager code 2 (0000)
230
NO
(1111)
DEFAULT
CONFIG. 3
01:01
00:00
NO
(- - - -)
6
(- - - -)
Installation and Programming Manual - СА62 Alarm Control Panel
63
64
SUPPLEMENTS - СА62 Alarm Control Panel
SUPPLEMENT В
Examples for Security Application with CA62
For illustration of the default factory configurations here are shown some examples for organizing the security
system.
The symbols used in the examples below have the following meaning:
MC - Magnetic contact;
PIR - Motion PIR detector;
KBD - Control keyboard;
СА62 - Control panel;
Zone n - Zone number.
DEFAULT CONFIGURATION 1
Office 4
Office 3
BookKeeping
Default codes:
• User 1 - 1111
• Manager - 0000
• Engineer - 7777
Partitions in the system:
Corridor
- PART А
Office 2
Office 1
Central
Entrance
Entrance PART A
PARTITION A
General information for DEFAULT CONFIGURATION 1:
• Zones - 6
• 1 partition - А
• 1 keyboard (suitable models LED61, LED62, LED63VG, LCD62, LCD62B, LCD63)
Short programming table for DEFAULT CONFIGURATION 1:
Zone
Type
1
Entry/Exit
2
Follow
3
Instant
4
Instant
5
Panic
6
Tamper
Attributes
Bypass
Disarm Enable
Bypass, Stay
Disarm Enable
Bypass, Stay
Disarm Enable
Bypass, Stay
Disarm Enable
Bypass, Stay
Disarm Enable
Part
Detectors
A
MC1
A
PIR1, PIR2
А
PIR3, PIR4
А
PIR5, PIR6
А
PIR6
Disarm Enable
А
Room
Central
Entrance
Corridor
Office 1
Office 2
Office 3
Office 4
Bookkeeping
TAMPER
from all of the All rooms
detectors
Control
KBD1
KBD1
KBD1
KBD1
KBD1
KBD1
65
SUPPLEMENTS - СА62 Alarm Control Panel
DEFAULT CONFIGURATION 2
PART A
Office 3
Office 4
Default codes:
• User 1 - 1111
• Manager - 0000
• Engineer - 7777
BookKeeping
Corridor
Office 1
Office 2
Entrance PART A
Central
Entrance А
Office 5
Office 6
Central
Entrance B
Entrance PART B
Partitions in the system:
Corridor
Office 7
Office 8
- PART А
- PART В
BookKeeping
PART B
General information for DEFAULT CONFIGURATION 2:
• Zones - 6
• 2 independent partitions - А and В
• 2 keyboards (suitable models LED61, LED62, LED63VG, LCD62, LCD62B, LCD63)
Short programming table for DEFAULT CONFIGURATION 2:
Zone
Type
Attributes
Part
Detectors
Bypass
1
Entry/Exit
A
MC1
Disarm Enable
Bypass, Stay
2
Follow
A
PIR1, PIR2
Disarm Enable
Bypass, Stay
PIR3, PIR4, PIR5,
3
Instant
А
Disarm Enable
PIR6, PIR7
Bypass, Stay
4
Entry/Exit
B
МС2
Disarm Enable
Bypass, Stay
5
Follow
B
PIR8, PIR9
Disarm Enable
Bypass, Stay
PIR10, PIR11, PIR12,
6
Instant
B
Disarm Enable
PIR13, PIR14
Room
Control
Central Entrance А
KBD1
Corridor
KBD1
Offices from 1 to 4,
Book-keeping
KBD1
Central Entrance В
KBD2
Corridor
KBD2
Offices from 5 to 8,
Book-keeping
KBD2
66
SUPPLEMENTS - СА62 Alarm Control Panel
DEFAULT CONFIGURATION 3
PART A
Office 3
Office 4
BookKeeping
Default codes:
• User 1 - 1111
• Manager - 0000
• Engineer - 7777
Corridor A
Office1
Office 2
Entrance PARTS A+B
Office 5
Office 6
Central
Entrance
A+B
Corridor B
Office 7
Office 8
Partitions in the system:
- PARTS А and В
- PART А
- PART В
BookKeeping
PART B
General information for DEFAULT CONFIGURATION 3:
• Zones - 6 (2 common, 2 to PART А, 2 to PART В)
• 2 partitions - А and В
• 1 keyboard (suitable models LED62, LCD63SE, LCD64)
Short programming table for DEFAULT CONFIGURATION 3:
Zone
Type
Attributes
Part
Detectors
Bypass
1
Entry/Exit
A and В
MC1
Disarm Enable
Bypass, Stay
PIR1, PIR2, PIR8,
2
Follow
A and В
Disarm Enable
PIR 9
Bypass, Stay
3
Instant
А
PIR5, PIR6, PIR7
Disarm Enable
Bypass, Stay
4
Instant
А
PIR3, PIR4
Disarm Enable
Bypass,
5
Instant
B
PIR10, PIR11, PIR14
Disarm Enable
Bypass,
6
Instant
B
PIR12, PIR13
Disarm Enable
Room
Control
Central Entrance A+B
KBD1
Corridors А and В
KBD1
Offices 3 and 4,
Book-keeping
KBD1
Offices 1 and 2
KBD1
Offices 7 and 8,
Book-keeping
KBD1
Offices 5 and 6
KBD1
SUPPLEMENTS - СА62 Alarm Control Panel
67
SUPPLEMENT С - Additional Information
Coding recordings in log events
The LOG Memory file can be viewed at ADDRESS 0024 in the Engineer menu (with entered valid engineer
code), at ADDRESS 300 in the Manager menu (with entered valid Manager code), and ADDRESS 1 in the
User menu (with entered valid user code with rights to view the log file).
In order to view a previous event press the ▼ button. In order to view a next event press the ▲ button. To
view additional information (xx is the user code or event zone number) press ENTER. Single click the ENTER
button to return to the list of events.
Recorded events can be viewed with the help of the table, which shows message coding within the system
and LED keypad indication. All possible combinations of keypad light-emitting diodes, the meaning of each
combination and the decoding of the specifying recording "xx" for the number of the user code or zone, are
shown for ease in reading log event recordings.
LED
Indication
Event
number

1
Burglary Alarm type event in xx zone

2
Burglary Alarm type restoring event in xx zone

3
Fire type alarm event in xx zone

4
Fire type restoring event in xx zone

5
Panic type alarm event in xx zone

6
Panic type restoring event in xx zone

7
Tamper type alarm event in xx zone

8
Tamper type restoring event in xx zone

9
Medical type alarm event in xx zone

10
Medical type restoring event in xx zone

11
Burglary Alarm type xx zone bypass

12
Burglary Alarm type xx zone bypass restoring

13
Fire type xx zone bypass

14
Fire type xx zone bypass restoring

15
Panic type xx zone bypass

16
Panic type xx zone bypass restoring

17
Tamper type xx zone bypass

18
Tamper type xx zone bypass restoring

19
Medical type xx zone bypass

20
Medical type xx zone bypass restoring

21
Disarm by xx user

22
Remote disarming by xx user

23
Disarming by key-switch in xx zone

24
Arming by xx user

25
Remote arming by xx user

26
Arming by key-switch in xx zone

27
Quick arm type arming
Description
68
SUPPLEMENTS - СА62 Alarm Control Panel

28
Program mode entry

29
Program mode exit

30
Entering ambush code by xx user

31
Telephone line failure

32
Recovery of faulty telephone line

33
Unsuccessful communication

34
Periodic test message communication

35
Digital communicator manual test

36
Fuse blown

37
Restored fuse

38
System default RESET

39
Loss of 220 V AC power supply

40
Restored 220 V AC power supply

41
Low battery charge level

42
Restored battery charge level

43
Activated zone with attribute “Write to log” (ADDRESS 2хх2)

44
Restored zone with attribute “Write to log” (ADDRESS 2хх2)

45
Activated zone with AUX attribute “24h Burglary” (ADDRESS 2хх4)

46
Activated zone with AUX attribute “AC LOST” (ADDRESS 2хх4)

47
Activated zone with AUX attribute “Battery Low” (ADDRESS 2хх4)

48
Activated zone with AUX attribute “GSM Link Trouble” (ADDRESS 2хх4)

49
Activated zone with AUX attribute “Gas Detector” (ADDRESS 2хх4)

50
Activated zone with AUX attribute “Refrigeration” (ADDRESS 2хх4)

51
Activated zone with AUX attribute “Loss of Heat” (ADDRESS 2хх4)

52
Activated zone with AUX attribute “Water Leakage” (ADDRESS 2хх4)

53
Activated zone with AUX attribute “Foil Break” (ADDRESS 2хх4)

54
Activated zone with AUX attribute “Low bottled gas level” (ADDRESS 2хх4)

55
Activated zone with AUX attribute “High temperature” (ADDRESS 2хх4)

56
Activated zone with AUX attribute “Low temperature” (ADDRESS 2хх4)

57
Restored zone with AUX attribute “24h Burglary” (ADDRESS 2хх4)

58
Restored zone with AUX attribute “AC LOST” (ADDRESS 2хх4)

59
Restored zone with AUX attribute “Battery Low” (ADDRESS 2хх4)

60
Restored zone with AUX attribute “GSM Link Trouble” (ADDRESS 2хх4)

61
Restored zone with AUX attribute “Gas Detector” (ADDRESS 2хх4)

62
Restored zone with AUX attribute “Refrigeration” (ADDRESS 2хх4)

63
Restored zone with AUX attribute “Loss of Heat” (ADDRESS 2хх4)
SUPPLEMENTS - СА62 Alarm Control Panel
Table of protocol Contact ID transmitted codes from CA62
Code
Description
100 - Medical alarm
Medical alarm
110 - Fire alarm
Fire alarm
120 - Panic alarm
Panic alarm
121 - Duress code
Code entered under duress
130 - Burglary alarm
Alarm
133 - 24 h Burglary
24-hour Burglary type zone
137 - Tamper alarm
Tamper alarm
138 - Оpening of zone with attr. Write to log
Activated zone with attribute "Write to log"
151 - Gas detector
Activated gas detector
152 - Refrigeration
Activated refrigeration sensor
153 - Loss of heat
Loss of heat (activated heat sensor)
154 - Water leakage
Activated water leakage detector
155 - Foil Break
Foil break
157 - Low bottled gas level
Low bottled gas level
158 - High temperature
High temperature in the premises
159 - Low temperature
Low temperature in the premises
300 - System trouble
Trouble in the system
301 - AC Loss
No 220 V power supply
302 - Battery low
Low battery charging level
305 - System RESET
System parameters default reset
311 - Battery missing
The battery is lost
330 - GSM link trouble
GSM Communication failure
338 - Closing of zone with attr. Write to log
Restored zone with attribute "Write to log"
351 - Teleco Fail
Telephone line failure
354 - Failure to communicate
Communication error
401 - Open/Close by user
Arming/ Disarming by user
407 - Remote Arm/ Disarm
Remote Arming/Disarming
408 - Quick arm
Quick arming (no code)
409 - Keyswitch Open/Close
Arming/Disarming from key-switch
571 - Fire bypass
Bypassing a FIRE type zone
572 - 24 h zone bypass
Bypassing a 24 h Burglary type zone
573 - Burglary bypass
Bypassing an Entry/Exit, Follow or Instant type zone
601 - Manual TEST report
Manual TEST signal
602 - Periodic TEST report
Periodic TEST signal
627 - Program mode entry
Engineer programming mode entry
628 - Program mode exit
Engineer programming mode exit
69
70
SUPPLEMENTS - СА62 Alarm Control Panel
Table of protocol SIA transmitted codes from CA62
Code
Description
AR
AC Restore
Restore 220V power supply
AT
AC Loss
No 220 V power supply
BA
Burglary alarm
Alarm
BB
Burglary bypass
Bypassing an Entry/Exit, Follow or Instant type zone
BH
Burglary Restore
Restore alarm
BU
Burglary bypass Restore
Restore after Bypassing an Entry/Exit, Follow or Instant type zone
CL
Quick arm
Quick arming (no code)
CL
Arming by user
Arming by user
CQ Remote arming
Remote ARMING
CS
Arming by keyswitch
Arming from key-switch
FA
Fire alarm
Fire alarm
FB
Fire bypass
Bypassing a FIRE type zone
FH
Fire Restore
Restore after Fire alarm
FU
Fire bypass Restore
Restore after bypassing a FIRE type zone
GA
Gas detector
Activated gas detector in the premises
GH Low bottled gas level restore
Restored low bottled gas level
GR Gas detector restore
Restored gas detector
GT
Low bottled gas level
Activated detector for low bottled gas level
HA
Duress code
Code introduced under duress
IA
Foil break
Foil break
IR
Foil break restore
Restored foil break
KA
High temperature
High temperature in the premises
KR
High temperature restore
Restored normal temperature in the premises
LB
Program mode entry
Engineer programming mode entry
LX
Program mode exit
Engineer programming mode exit
MA Medical alarm
Medical alarm
MB Medical bypass
Bypassing a Medical type zone
MH Medical Restore
Restore after Medical alarm
MU Medical bypass Restore
Restore after bypassing a Medical type zone
NR
GSM Link trouble restore
Restored GSM communication link
NT
GSM Link trouble
GSM communication link trouble
OP
Disarm by user
Disarming by user
OQ Remote disarm
Remote disarming
OS
Disarm by keyswitch
Disarming from key-switch
PA
Panic alarm
Panic alarm
PB
Panic bypass
Bypassing a Panic type zone
PH
Panic Restore
Bypassing a Panic type zone
PU
Panic bypass Restore
Restore after bypassing a Panic type zone
RP
Periodic TEST report
Periodic TEST signal
RX
Manual TEST report
Manual TEST signal
TA
Tamper alarm
Tamper alarm
TB
Tamper bypass
Bypassing a Tamper type zone
TH
Tamper Restore
Restore after Tamper alarm
TU
Tamper bypass Restore
Restore after bypassing a Tamper type zone
UA
Opening of zone with attr. Write to log Activated zone with attribute "Write to log"
UH
Closing of zone with attr. Write to log
Restored zone with attribute "Write to log"
WA Water leakage
Activated water leakage detector
WR Water leakage restore
Restored water leakage detector
SUPPLEMENTS - СА62 Alarm Control Panel
YC
Failure to communicate
Communication error
YK
Telephone line Retsore
Restored telephone line
YM Battery low
Low battery charge level
YP
Fuse blown
Blown fuse
YQ
Fuse Restore
Restored fuse
YR
Battery Restore
Restored battery
YS
Telephone line Fault
Telephone line failure
YT
Battery missing
No battery
YW System RESET
71
System parameters default reset
ZA
Refrigeration
Loss of heat
Low temperature
Activated detector for refrigeration
Activated heat detector
Low temperature in the premises
ZR
Refrigeration restore
Loss of heat restore
Low temperature restore
Restored detector for refrigerating
Restored heat detector
Restored normal temperature level
Hexadecimal Programming Table
Value
0
1
2
3
4
5
6
7
8
9
А
В
С
D
E
F
Status LED 3 ... 6
LED3
○
○
○
○
○
○
○
○
●
●
●
●
●
●
●
●
LED4
○
○
○
○
●
●
●
●
○
○
○
○
●
●
●
●
LED5
○
○
●
●
○
○
●
●
○
○
●
●
○
○
●
●
LED6
○
●
○
●
○
●
○
●
○
●
○
●
○
●
○
●
Buttons
combination
0
1
2
3
4
5
Legend:
○ - The LED is off.
● - The LED is on.
The expression “ARM + 1” means
pressing the “ARM” and “1” buttons in succession.
6
7
8
9
ARM + 0
ARM + 1
ARM + 2
ARM + 3
ARM + 4
ARM + 5
Solving of Technical Problems During Powering up of CA62
In case of technical trouble  - No 220 V power supply, to solve the problem do as follows:
 Turn off the main power supply;
 Check the main power supply fuse F - 0.63А. If the fuse is blown out change it with new one. If the fuse is not damaged, check the connection between the main power cables and the control panel.
 Switch on the main 220V power supply.
 Wait for 3 minutes and if after this period the alarm panel does not restores its normal operating call the
maintenance engineer.
In case of technical trouble  - Fuse burned, to solve the problem do as follows:
 Turn off the main power supply;
 Turn off the back-up power supply (open the CА62 mounting box and switch off the black wire to the
accumulator battery;
 Wait for 1 minute while the resettable (PTC) fuses F1, F2 and F3 are restored - see Figure 5.
 Switch on the main 220V power supply.
 Connect the black wire from the control panel to the accumulator battery.
72
SUPPLEMENTS - СА62 Alarm Control Panel
SUPPLEMENT D - Algorithms for Operation of ZONES with Key-Switch Type
In the tables below is described the working algorithm for Key-Switch type zones, according to the programmed at ADDRESS 2013 parameter - Pulse or Latch. The operation of the Partition(s) and the sounder(s) is described on the right
side of the tables. The operation strongly depends on the current status of the specified parameters pointed out on the
left side of the table. To follow the operation of a partition and/or sounder the installer has to know what is the current
status of the system and what attributes and parameters have been programmed before that.
Algorithm for Key-Switch type zones operating, Pulse parameter set on,
when the zone is attached to ONE Partition
Attribute
Disarm
Enable
Partition
ARMing status
Sounder
status
Enabled
DISARMED
OFF
Enabled
DISARMED
Enabled
ARMED
Enabled
ARMED
Disabled
Operation at incoming
impulse from the zone
Partition
Sounder
ARMING
-
ON
-
STOP
OFF
DISARMING
-
ON
DISARMING
STOP
DISARMED
OFF
ARMING
-
Disabled
DISARMED
ON
-
STOP
Disabled
ARMED
OFF
-
-
Disabled
ARMED
ON
-
STOP
Algorithm for Key-Switch type zones operating, Pulse parameter set on,
when the zone is attached to TWO Partitions
Attribute
Disarm
Enable
Partition A
ARMing
status
Partition B
ARMing
status
Partition A
Sounder
status
Partition B
Sounder
status
Enabled
DISARMED
DISARMED
OFF
Enabled
DISARMED
DISARMED
Enabled
DISARMED
DISARMED
Enabled
DISARMED
DISARMED
Enabled
ARMED
Enabled
Enabled
Operation at incoming impulse from the zone
Sounder Sounder
Part. А
Part. В
Partition А
Partition В
OFF
ARMING
ARMING
-
ON
OFF
-
-
STOP
-
OFF
ON
-
-
-
STOP
ON
ON
-
-
STOP
STOP
DISARMED
OFF
OFF
DISARMING
-
-
-
ARMED
DISARMED
ON
OFF
DISARMING
-
STOP
-
ARMED
DISARMED
OFF
ON
-
-
-
STOP
Enabled
ARMED
DISARMED
ON
ON
DISARMING
STOP
DISARMED
ARMED
OFF
OFF
-
DISARMING
STOP
Enabled
-
-
Enabled
DISARMED
ARMED
ON
OFF
-
-
STOP
-
Enabled
DISARMED
ARMED
OFF
ON
-
DISARMING
-
STOP
Enabled
DISARMED
ARMED
ON
ON
-
DISARMING
STOP
STOP
Enabled
ARMED
ARMED
OFF
OFF
DISARMING DISARMING
-
-
Enabled
ARMED
ARMED
ON
OFF
DISARMING DISARMING
STOP
-
Enabled
ARMED
ARMED
OFF
ON
DISARMING DISARMING
-
STOP
Enabled
ARMED
ARMED
ON
ON
DISARMING DISARMING
STOP
STOP
Disabled
DISARMED
DISARMED
OFF
OFF
ARNING
ARMING
-
-
Disabled
DISARMED
DISARMED
ON
OFF
-
-
STOP
-
Disabled
DISARMED
DISARMED
OFF
ON
-
-
-
STOP
Disabled
DISARMED
DISARMED
ON
ON
-
-
STOP
STOP
Disabled
ARMED
DISARMED
OFF
OFF
-
ARMING
-
-
Disabled
ARMED
DISARMED
ON
OFF
-
-
STOP
-
Disabled
ARMED
DISARMED
OFF
ON
-
-
-
STOP
Disabled
ARMED
DISARMED
ON
ON
-
-
STOP
STOP
Disabled
DISARMED
ARMED
OFF
OFF
ARMING
-
-
-
-
73
SUPPLEMENTS - СА62 Alarm Control Panel
Disabled
DISARMED
ARMED
ON
OFF
-
-
STOP
-
Disabled
DISARMED
ARMED
OFF
ON
-
-
-
STOP
Disabled
DISARMED
ARMED
ON
ON
-
-
STOP
STOP
Disabled
ARMED
ARMED
OFF
OFF
-
-
-
-
Disabled
ARMED
ARMED
ON
OFF
-
-
STOP
-
Disabled
ARMED
ARMED
OFF
ON
-
-
-
STOP
Disabled
ARMED
ARMED
ON
ON
-
-
STOP
STOP
АAlgorithm for Key-Switch type zones operating, Latch parameter set on,
when the zone is attached to ONE Partition
Operation at zone activating
Operation at zone de-activating
Partition
ARMing status
Sounder
status
Partititon
Sounder
Partition
Sounder
DISARMED
OFF
ARMING
-
-
-
DISARMED
ON
ARMING
STOP
-
-
ARMED
OFF
-
-
DISARMING
-
ARMED
ON
-
-
DISARMING
STOP
Algorithm for Key-Switch type zones operating, Latch parameter set on,
when the zone is attached to TWO Partitions
Operation at zone activating
Operation at zone de-activating
Part. A Part. B
Sounder Sounder
ARMing ARMing
Partition Partition Sounder Sounder Partition Partition Sounder Sounder
A
В
Status Status
A
В
А
B
A
В
А
B
Disarmed Disarmed
OFF
OFF
Arming
Arming
-
-
-
-
-
-
Disarmed Disarmed
ON
OFF
Arming
Arming
STOP
-
-
-
STOP
-
Disarmed Disarmed
OFF
ON
Arming
Arming
-
STOP
-
-
-
STOP
Disarmed Disarmed
ON
ON
Arming
Arming
STOP
STOP
-
-
STOP
STOP
Armed Disarmed
OFF
OFF
-
Arming
-
-
Disarming
-
-
-
Armed Disarmed
ON
OFF
-
Arming
STOP
-
Disarming
-
STOP
-
Armed Disarmed
OFF
ON
-
Arming
-
STOP
Disarming
-
-
STOP
Armed Disarmed
ON
ON
-
Arming
STOP
STOP
Disarming
-
STOP
STOP
Disarmed Armed
OFF
OFF
Arming
-
-
-
-
Disarming
-
-
Disarmed Armed
ON
OFF
Arming
-
STOP
-
-
Disarming
STOP
-
Disarmed Armed
OFF
ON
Arming
-
-
STOP
-
Disarming
-
STOP
Disarmed Armed
ON
ON
Arming
-
STOP
STOP
-
Disarming
STOP
STOP
Armed
Armed
OFF
OFF
-
-
-
-
Disarming Disarming
-
-
Armed
Armed
ON
OFF
-
-
STOP
-
Disarming Disarming
STOP
-
Armed
Armed
OFF
ON
-
-
-
STOP
Disarming Disarming
-
STOP
Armed
Armed
ON
ON
-
-
STOP
STOP
Disarming Disarming
STOP
STOP
74
SUPPLEMENTS - СА62 Alarm Control Panel
SUPPLEMENT Е
Algorithm for Recording and Listening of Voice Messages
Recording of voice messages
Recording and listening of voice messages in the
system is programed at ADDRESS 6030 at the
Engineer Programming menu.
Follow the steps of the algorithm to record and
listen to the voice messages.
Examples for voice messages in the system are
shown in the applied tables.
Listening the recorded messages
SUPPLEMENTS - СА62 Alarm Control Panel
Examples for voice messages
MESSAGE BY ZONE (at ADDRESS 6035 is set 0) Messag.
Event
Example message
1
Alarm or tamper from Zone 1.
“ Alarm from Zone 1” or “Alarm in Entrance zone”
2
Alarm or tamper from Zone 2.
“Alarm from Zone 2” or “Alarm in the corridor”
3
Alarm or tamper from Zone 3.
“Alarm from Zone 3” or “Alarm in the children room”
4
Alarm or tamper from Zone 4.
“Alarm from Zone 4” or “Alarm in the dinning room”
5
Alarm or tamper from Zone 5.
“Alarm from Zone 5” or “Alarm in the bedroom”
6
Alarm or tamper from Zone 6.
“Alarm from Zone 6” or “ Cable interrupting in the alarm system”
7
Disarming with Ambush code
“Duress code have been entered”
8
Personal message.
“Message for Mr. John Smith”
MESSAGE BY EVENT (at ADDRESS 6035 is set 1) Messag.
Event
Example message
1
Alarm in the system
“ Burglary alarm”
2
Panic alarm in the system
“ Panic or Duress code have been entered”
3
Tamper alarm in the system
“ Cable interrupting in the alarm system”
4
Fire alarm in the system
“Fire”
5
Medical alarm in the system
“ Medical alarm”
6
AC loss
“AC power supply interrupting”
7
Battery low
“Battery too low”
8
Common message
“Message for Mr. John Smith”
SUPPLEMENT F - General connection diagram
75
18020603, Rev. A, 02/2009
www.teletek-electronics.com
Address: Bulgaria, Sofia - 1407, 14А Srebarna Str.
Tel.: +359 2 9694 700, Fax: +359 2 962 52 13
e-mail: info@teletek-electronics.bg
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising