Edimax | AR-7064g+ | User`s manual | Edimax AR-7064g+ User`s manual

Edimax AR-7064g+ User`s manual
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
FCC DoC TEST REPORT
According to
FCC Part 15
Test
Κ ADSL2+Wireless-G Router, ADSL2+Router with 4 Port Switch
Κ AR-7064g+, AR-7064+
Κ EDIMAX TECHNOLOGY CO., LTD.
Item
Model
No.
Responsible
Party
NO. 3, WU CHUAN 3RD ROAD, WU-KU INDUSTRIAL PARK,
TAIPEI HSIEN, TAIWAN, R. O. C.
Address
Issued Date
Subpart B
:
NVLAP Signature :
JAN.
19,
2006
M. Y. Tsui
M. Y. Tsui / President
ΘThe test report shall not be reproduced except in full, without the written approval of
the laboratory.
ΘThe report must not be used by the client to claim product endorsement by NVLAP or any
agency of the United States government.
ΘThis report is only for item test which described in page 4 .
ΘThe testing result in this report are traceable to national and international standard .
PEP TESTING LABORATORY
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL : 886-2-26922097
FAX : 886-2-26956236
Page 1
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
Table of Contents
1.
SCOPE
3
2.
PRODUCT INFORMATION
4
3.
EUT DESCRIPTION AND TEST CONCLUSION
5
4.
MODIFICATION(S)
6
5.
TEST SOFTWARE USED
6
6.
SUPPORT EQUIPMENT USED
7
7.
DESCRIPTION OF CONDUCTED EMISSIONS TEST
9
8.
DESCRIPTION OF RADIATED EMISSIONS TEST
10
9.
CONDUCTED EMISSIONS TEST SETUP PHOTO
13
10.
CONDUCTED EMISSIONS TEST DATA
14
11.
RADIATED EMISSIONS TEST SETUP PHOTOS
17
12.
RADIATED EMISSIONS TEST DATA
18
13.
LIST OF MEASURED INSTRUMENTS
20
14.
DUTIES OF THE RESPONSIBLE PARTY
21
15.
LABELLING REQUIREMENTS
22
16.
INFORMATION TO THE USER
23
17.
EUT PHOTOGRAPHS
24
Page 2
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
1. Scope
Measurement and determination of electromagnetic emissions (EME) of radio frequency devices
including intentional and/or unintentional radiators for compliance with the technical rules and
regulations of the Federal Communications Commission under EUT Docket 95-19 Declaration of
Conformity(DoC).
Responsible
Party*:
NO. 3, WU CHUAN 3RD ROAD, WU-KU INDUSTRIAL
PARK, TAIPEI HSIEN, TAIWAN, R. O. C.
Address:
Contact
Phone
EDIMAX TECHNOLOGY CO., LTD.
Person:
No.:
TRACY CHENG /
ASSISTANT
886-2-22995648
Fax
No.:
886-2-22995647
Regulation:
FCC Part 15 & Part 2; Docket 95-19
Limitation:
CISPR 22 CLASS B
Test Procedure:
ANSI C63.4 (2001)
Test Item:
DSL2+Wireless-G Router, ADSL2+Router with 4 Port Switch
Model No.:
AR-7064g+, AR-7064+
Serial No.:
N/A
Place of Test:
PEP Testing Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL : 886-2-26922097 FAX : 886-2-26956236
Measurement Uncertainty :
The uncertainty of the testing result is given as below. The method of uncertainty
Calculation is provided in PEP Testing Lab document No. QP-T-28-B & QP-T-27-B
Frequency ( MHz )
0.15 ~ 30
30 ~ 1000
Expanded Uncertainty Ӵc
1.4 (dB)
2.84 (dB)
ϡʳ95% Confidence Level; K=2
Page 3
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
2. Product Information
a.
EUT Name:
b.
Model No.
c.
ADSL2+Wireless-G Router
Κ
CPU TypeΚ
AR-7064g+
N/A
Κ
N/A
d.
CPU Frequency
e.
Crystal/Oscillator(s)
f.
Chassis Used
g.
Port/Connector(s)
h.
Power Rating
Adapter ----ManufacturerΚAHEAD
Model No. : JAD-0901500E
Input : AC 230V 50Hz 150mA
Output : DC 9V 1500mA
i.
Condition of the EUT :
ϭ Prototype Sample
ϭ Production Sample
j.
Test Item Receipt Date :
SEP.
k.
Date(s) of performance of test:
Κ
Κ
Κ
24 MHz, 25 MHz, 17.664 MHz
ABS
Κ
RJ45 Port * 4, RJ11 Port * 1
23,
SEP.
Page 4
Engineering Sample
2005
23,
of 24
2005– OCT. 28, 2005
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
3. EUT Description and Test Conclusion
The EUT: ADSL2 + Wireless-G Router model AR-7064g+ and ADSL2 + Router With 4 Port
Switch model AR-7064+. in this reissued test report is originated from the model: A2WR
listed in PEP Report No. E 940705. The use of this test report by EDIMAX TECHNOLOGY
CO., LTD. is authorized by the original applicant. The following EUT configuration setup for
test and the test result are both originated and copied from PEP Report No. E 940705.
The equipment under test (EUT) is are ADSL2 + Wireless-G Router model AR-7064g+ and
ADSL2 + Router With 4 Port Switch model AR-7064+. These two models have identical
electrical design and construction except that model AR-7064g+ comes with additional
built-in wireless module and wireless antenna. Unless otherwise specified, we took the
worst-case model: AR-7064g+ as representative instead of serial model for tests. The
equipment is designed for multiple computers to share resources from worldwide area
network and local area network through Ethernet and wireless connections. AC adaptor
supplies EUT 9Vdc from ac mains. For more detail specification about the EUT, please refer
to the user’s manual.
Test method: According to the major function designed, the EUT worst-case configuration
was set up by the following steps for test:
(A)
Connect EUT one RJ-45 port to PC LAN card.
(B)
Plug the rest of EUT RJ-45 ports and RJ-11 port by data cables.
All corresponding peripherals to PC I/O ports and EUT were set to proceed
with test. The test was respectively carried out on EUT operational conditions
of Ethernet transmission mode and TX-On mode and the worst-case test result
of each test mode was recorded and provided in this report.
Conducted emission test:
The system was setup with the EMI diagnostic software running. The power line conducted
EMI tests were run on the line and neutral conductors of the power cord and the results were
recorded. The effect of varying the position of the interface cables has been investigated to
find the worst-case configuration that produces maximum emission.
At the frequencies where the peak values of the emission exceeded the quasi-peak limit, the
emissions were also measured with the quasi-peak detectors. The average detector also
measured the emission either (A) quasi-peak values were under quasi-peak limit but exceeded
average limit, or (B) peak values were under quasi-peak limit but exceeded average limit.
Radiated emission test:
The maximum readings were found by varying the height of antenna and then rotating the
turntable. Both polarization of antenna, horizontal and vertical, are measured. The effect of
varying the position of the interface cables has been investigated to find the configuration that
produces maximum emission.
The highest emissions were also analyzed in details by operating the spectrum analyzer in
fixed tuned quasi-peak mode to determine the precise amplitude of the emissions.
Page 5
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
4. Modification(s):
For more details about the modification(s) incorporated into EUT, please refer to EUT
photographs listed in this report.
5. Test Software Used
(A) PING command was executed to access EUT on network during the test.
(B) EMCTEST program that continuously generates a complete line of repeating “H” letter was
the software used during test.
(C) Testutility_3.1 program was the software used to operate EUT wireless function during the
test.
Page 6
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
6. Support Equipment Used
1. Personal Computer (PC3) * 2
2. Monitor (MON1 15”) * 2
CPU : Intel P4 Socket 478 1.6GHz
FCC ID Declaration of Conformity(DoC)
Manufacturer LEMEL
Model Number LMIH1A2
Power Supply Switching
Power Cord Non-Shielded, Detachable, 1.8m
Data Cable
N/A
Κ
Κ
Κ
Κ
Κ
Κ
Κ
FCC ID Declaration of Conformity(DoC)
Manufacturer SAMSUNG
Model Number 550S
Power Supply Switching
Power Cord Non-Shielded, Detachable, 1.8m
Data Cable 1 > Shielded , Non-detachable,1.2m
Κ
Κ
Κ
Κ
Κ
2 > Back Shell : Metal
3. Printer (PRN1)
Κ
FCC ID B94C2642X
Manufacturer Hewlett-Packard
Model Number C2642E
Power Supply Linear, 30Vdc O/P
Power Cable Non-Shielded , Detachable,1.8m
Data Cable 1 > Shielded , Detachable,1.2m
Κ
Κ
Κ
Κ
Κ
2 > Back Shell : Metal
4. Modem (MOD1)
Κ
FCC ID IFAXDM1414
Manufacturer ACEEX
Model Number 1414
Power Supply Linear, 9Vac O/P
Power Cable Non-Shielded , Detachable,1.7m
Data Cable 1 > Shielded , Detachable,1m
Κ
Κ
Κ
Κ
Κ
2 > Back Shell : Metal
Page 7
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
5. Keyboard (KBS1 PS/2) * 2
Κ
FCC ID E5XKB5121WTH0110
Manufacturer BTC
Model Number 5121W
Power Supply +5Vdc from PS2 of PC
Power Cord N/A
Data Cable 1 > Shielded , Non-detachable,1.6m
Κ
Κ
Κ
Κ
Κ
2 > Back Shell : Metal
6. Mouse (MOUS/1 PS/2) * 2
Κ
FCC ID DZL211106
Manufacturer LOGITECH
Model Number M-S43
Power Supply +5Vdc from PS2 of PC
Power Cord N/A
Data Cable 1 > Shielded , Non-detachable,1.8m
Κ
Κ
Κ
Κ
Κ
2 > Back Shell : Metal
Page 8
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
7. Description of Conducted Emissions Test
7.1 Conducted Emissions
A 1m x1.5m wooden table 80 cm high is placed 40cm away from the vertical wall. Two AMN
are bonded to the grounding plane. The EUT is powered from the designated AMN and the
support equipment is powered from another designated AMN. Powers to the AMN are filtered
by a high-current high insertion loss power line filters. All electrical cables are shielded by
braided tinned copper zipper tubing with inner diameter of 1/2”. All interconnecting cables
more than 1 meter were shortened by non-inductive bundling (serpentine fashion) to a 1-meter
length.
Sufficient time for the EUT, support equipment, and test equipment was allowed in order for
them to warm up to their normal operating condition. The RF output of the AMN was
connected to the spectrum analyzer to determine the frequency producing the maximum EME
from the EUT.
The spectrum was scanned from 150kHz to 30 MHz with1.5 sec sweep time. The frequency
producing the maximum level was re-examined using Quasi-Peak adapter. The detector
function was set to CISPR quasi-peak mode. The bandwidth of the receiver was set to 10kHz.
The EUT, support equipment, and interconnecting cables were re-arranged and manipulated to
maximize each EME emission. Each emission was maximized by: switching power lines;
varying the mode of operation or resolution; clock or data exchange speed; scrolling H pattern
to the EUT and/or support equipment, and powering the monitor from the floor mounted outlet
box and the computer aux AC outlet, if applicable; whichever determined the worst-case
emission.
7.2 Conducted Emissions Limits
Frequency
Maximum
Class
RF
Line
Voltage dB(uV)
A
Class
B
MHz
QUASI-PEAK
AVERAGE
QUASI-PEAK
AVERAGE
0.15 - 0.50
79
66
66-56
56-46
0.50 - 5.0
73
60
56
46
5.0 - 30
73
60
60
50
Remarks : In the above table, the tighter limit applies at the band edges.
Page 9
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
8. Description of Radiated Emissions Test
8.1 Radiated Emissions
Preliminary measurements were made indoors chamber at 3 meter using broadband
antennas, broadband amplifier, and spectrum analyzer to determine the frequency
producing the maximum EME. Appropriate precaution was taken to ensure that all EME
from the EUT were maximized and investigated. The system configuration, clock speed,
mode of operation or video resolution, turntable azimuth with respect to the antenna were
noted for each frequency found. The spectrum was scanned from 30 to 1000 MHz using
logbicon antenna. Above 1GHz, linearly polarized double ridge horn antenna was used.
Final measurements were made outdoors at 10-meter test range using logbicon antenna
and horn antenna. The test equipment was placed on a wooden bench situated on a 1.5x1
meter area adjacent to the measurement area. Sufficient time for the EUT, support
equipment, and test equipment was allowed in order for them to warm up to their normal
operating condition. Each frequency found during pre-scan measurements was
re-examined and investigated using Quasi-Peak Adapter. The detector function was set to
CISPR quasi-peak mode and the bandwidth of the receiver was set to 120kHz.
The turntable containing the system was rotated; the antenna height was varied 1 to 4
meters and stopped at the azimuth or height producing the maximum emission. Each
emission was maximized by: varying mode of operation or resolution; clock or data
exchange speed; scrolling H pattern to the EUT and/or support equipment, and powering
the monitor from the floor mounted outlet box and the computer aux AC outlet , if
applicable; and changing the polarity of the antenna, whichever determined the worst-case
emission. Photographs of the worst-case emission can be seen in radiated emission test
photo.
Page 10
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
8.2 Test Configuration
10
cm
10
cm
EUT
NONCONDUCTIVE
TABLE 1.5 x 1 METER
5
5
6
80 cm TO
GROUND PLANE
7
4
2
1
8
3
40 cm
8
CONDUCTING GROUND
PLANE EXTENDS AT
LEAST 0.5m BEYOND
EUT SYSTEM FOOTPRINT
LEGEND
1.
Interconnecting cables which hang closer than 40 cm to the ground plane shall be folded back and forth forming a bundle 30 to 40
cm long. hanging approximately in the middle between ground plane and table.
2.
I/O cables which are connected to a peripheral hall be bundled in center. The end of the cable may b terminated if required using
correct terminating impedance. The total length shall not exceed 1 m.
3.
If LISN are kept in the test setup for radiated emissions, it is preferred that they be installed under the ground if requires
receptacle flush with the ground plane.
4.
Cables of hand-operated devices, such as keyboards, KEYPADs, etc., have to be placed as close as possible to the controller.
5.
Non-EUT components of EUT system being tested.
6.
The rear of all components of the system under test shall be located flush with the rear of the table.
7.
No vertical conducting wall used.
8.
Power cords drape to the floor and are routed over to receptacle.
Page 11
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
8.3 Radiated Emission Limits
Limits
for
radiated disturbance of Class A ITE
a measuring distance of 10 m
Frequency
MHz
at
Field Strength
dB(ӴV/m)
30
to
230
40
230
to
1 000
47
NOTES
1 The lower limit shall apply at the transition frequency.
2 Additional provisions may be required for cases where
interference occurs.
Limits
for
radiated disturbance of Class B
a measuring distance of 10 m
Frequency
MHz
ITE
at
Field Strength
dB(ӴV/m)
30
to
230
30
230
to
1 000
37
NOTES
1 The lower limit shall apply at the transition frequency.
2 Additional provisions may be required for cases where
interference occurs.
Page 12
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
9. Conducted Emissions Test Setup Photo
< FRONT
Page 13
VIEW >
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
10. Conducted Emissions Test Data
Model No.
Frequency range
Detector
Temperature
Humidity
Test
Data :
: AR-7064g+
: 150KHz to 30MHz
: Quasi-peak Value
: 29
: 52 %
к
#
521
ˏ ˟˜ˡ˘ʳˑ
#
519
ˏˡ˘˨˧˥˔˟ˑ
Note 1. Level = Read Level + Cable Loss + Probe (LISN)
2. Over Limit = Level – Limit = Margin
Page 14
of 24
NVLAP LAB CODE: 200097-0-
!
!
!
!
!
Page 15
of 24
NVLAP LAB CODE: 200097-0-
!
!
!
!
!
!
!
!
!
!
!
!
Page 16
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
11. Radiated Emissions Test Setup Photos
< FRONT
< REAR
Page 17
VIEW >
VIEW >
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
12. Radiated Emissions Test Data
Model No.
Frequency range
Frequency range
Temperature
Antenna
: AR-7064g+
: 30MHz to 1GHz
: above 1GHz
: 29o C
polarization :
Over
Freq.
(MHz)
Level
Limit
(dBuV/m) (dB)
Limit
Detector
Detector
Humidity
: Quasi-Peak Value
: Quasi-Peak/Average Value
: 55 %
HORIZONTAL ; Test
Read
Antenna Cable
Line
Level
Factor
(dBuV/m) (dBuV) (dB)
Loss
(dB)
distance :
10m
;
Preamp
Factor
(dB)
Azimuth Antenna
(̓angle) High(m)
!
!!!236/111!!!31/62!!!.:/5:!!!41/11!!!39/14!!!23/69!!2/41!!!32/51!!!291/1!!!5/1!
!!!311/131!!!38/:3!!!.3/19!!!41/11!!!46/94!!!22/5:!!2/:1!!!32/41!!!!!1/1!!!5/1!!
!!!361/156!!!42/41!!!.6/81!!!48/11!!!49/91!!!22/61!!3/41!!!32/41!!!!!1/1!!!5/1!!!
!!!611/111!!!39/82!!!.9/3:!!!48/11!!!39/95!!!28/28!!4/61!!!31/91!!!291/1!!!4/6!!!
!!!636/3::!!!45/26!!!.3/96!!!48/11!!!44/68!!!28/78!!4/72!!!31/81!!!291/1!!!4/5!
!!!686/111!!!43/61!!!.5/61!!!48/11!!!41/83!!!29/78!!4/92!!!31/81!!!291/1!!!4/5
Note :
1.
2.
Level = Read Level + Antenna Factor + Cable Loss – Preamp Factor
Over Limit = Level – Limit Line
Page 18
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
Model No.
Frequency range
Frequency range
Temperature
Antenna
: AR-7064g+
: 30MHz to 1GHz
: above 1GHz
: 29o C
polarization :
Over
Freq.
(MHz)
Level
Limit
(dBuV/m) (dB)
Limit
Detector : Quasi-Peak Value
Detector : Quasi-Peak/Average Value
Humidity : 55 %
VERTICAL
Read
;
Test distance :
Antenna Cable
Line
Level
Factor
(dBuV/m) (dBuV) (dB)
Loss
(dB)
10m
;
Preamp
Factor
(dB)
Azimuth Antenna
(̓angle) High(m)
!
!!!!61/129!!!33/98!!!.8/24!!!41/11!!!44/18!!!21/81!!!1/61!!!32/51!!291/1!!!2/1!!
!!!286/133!!!34/19!!!.7/:3!!!41/11!!!39/81!!!25/19!!!2/81!!!32/51!!291/1!!!2/1!
!!!311/135!!!39/69!!!.2/53!!!41/11!!!47/5:!!!22/5:!!!2/:1!!!32/41!!291/1!!!2/1!!!!!
!!!361/141!!!43/71!!!.5/51!!!48/11!!!51/21!!!22/61!!!3/41!!!32/41!!291/1!!!2/1!!!
!!!611/111!!!45/25!!!.3/97!!!48/11!!!45/38!!!28/28!!!4/61!!!31/91!!!!1/1!!!2/1!!!
!!!636/63:!!!42/24!!!.6/98!!!48/11!!!41/5:!!!28/83!!!4/73!!!31/81!!291/1!!!2/1
Note :
1.
2.
Level = Read Level + Antenna Factor + Cable Loss – Preamp Factor
Over Limit = Level – Limit Line
Page 19
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
13. List of Measured Instruments
Test Mode
Conduction
( No.1)
Radiation
(OP No.1)
Instrument
Model No.
Serial No.
Next Cal. Date
Cal. Interval
R&S
Receiver
ESHS10
830223/008
May 22, 2006
1Year
Rolf Heine
LISN
NNB-4/63TL
98008
May 01, 2006
1Year
R&S
LISN
ESH3-Z5
844982/039
Aug. 06, 2006
1Year
Spectrum
Analyzer
R3261A
91720076
June 08, 2006
1Year
RF Cable
Rg400
N/A
May 12, 2006
1Year
Schaffner
ISN
T411
N/A
June 29, 2006
1Year
R&S
Receiver
ESVS30
863342/012
Apr. 23, 2006
1Year
Schaffner
Pre-amplifier
CPA9232
1028
May 20, 2006
1Year
10095
May 21, 2007
2Year
970 + 971
953 + 954
June 26, 2006
3Year
841104/037
Apr. 29, 2007
2Year
N/A
May 11, 2006
1Year
9904-1370
Aug. 24, 2006
1Year
COM-Power
AH-118
(1GHz~18GHz)
Horn Ant.
Schwarzbeck
VHAP
Precision Dipole
(30MHz~1GHz)
Ant
R &S Signal
SMY01
Generator
RF Cable
No. 1
EMCO
Antenna
(26MHz~2GHz)
3142B
Page 20
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
14. Duties of The Responsible Party
The responsible party upon signing or accepting the Declaration of Conformity as specified in
Section 2.906 of the FCC Rules hereby agrees to the duties listed below.
̺2.1073(a).
The responsible party warrants that each unit of equipment marketed under DoC is identical to the unit
tested and found acceptable with the standards and that the records maintained by the responsible party
continue to reflect the equipment being produced is within the variation that can be expected due to
quantity production and testing on a statistical bass.
̺2.1073(b).
The responsible party must have a written statement from the manufacturer or accredited test
laboratory that the equipment complies with the appropriate technical standards.
̺2.1073(c).
In case of transfer of control of equipment, as in the case of sale or merger, the new responsible party
shall bear the responsibility of continued compliance of the equipment.
̺2.1073(d).
Equipment shall be retested if any modifications or changes are made that could adversely affect the
emanation characteristics of the equipment.
̺2.1073(e).
If any modifications or changes made by anyone other than the responsible party, the party making the
modifications of changes, if located within the U.S., becomes the new responsible part. The new
responsible party must comply with all provisions for the DoC, including having test data on file
demonstrating that the product continues to comply with all of the applicable technical standards.
̺2.1075(a)(1).
The responsible party shall maintain records of the original design drawings and specifications and all
changes made to the product that may affect compliance.
̺2.1075(a)(2).
The responsible party shall maintain records of the procedures used for production inspection and
testing to insure the conformance with the FCC Rules.
̺2.946(a)(1).
The test report data shall be provided to the FCC within 14 days of delivery of request. The test
sample(s) shall be provided within 60 days of delivery of request.
̺2.946(b)
In case involving harmful interference or safety of life or property, the production sample must be
provided within 60 days, but not less than 14 days. Failure to comply with such a request with the
time frame shown may be cause for forfeiture, pursuant to Section 1.80 of Part 1 of the FCC Rules.
*The Responsible Party is the manufacturer, system integrator, or the importer as defined in Section
2.909 of the FCC Rules. The Rules. The Responsible Party for a DoC must be located within the
United States as specified in Section 2.1077.
Page 21
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
15. Labelling Requirements
The sample label shown below shall be permanently affixed at a conspicuous location on
the device, instructions manual or pamphlet supplied to the user and be readily visible to the
purchaser at the time of purchase. However, when the device is so small wherein placement
of the label with specified statement is not practicable, only the trade name, model number,
and the FCC logo must be displayed on the device per Section ̺15.19 (b)(1)(i).
Trade Name
Model Number
Page 22
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
16. Information To The User
For a Class B digital device or peripheral, the instructions furnished the user shall include the
following or similar statement, placed in a prominent location in the text of the manual:
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
-
Page 23
of 24
PEP
Testing
Laboratory
12-3Fl, No. 27-1, Lane 169, Kang-Ning St., Hsi-Chih,
Taipei Hsien, Taiwan, R. O. C.
TEL: 886-2-26922097
FAX: 886-2-26956236
NVLAP LAB CODE: 200097-0-
REPORT NO. :E940705(A)
17. EUT Photographs
Model
No. :
Page 24
AR-7064g+
of 24
DECLARATION OF CONFORMITY CERTIFICATE
Responsible Party :
EDIMAX TECHNOLOGY CO., LTD.
Address :
NO. 3, WU CHUAN 3RD ROAD, WU-KU INDUSTRIAL PARK,
TAIPEI HSIEN, TAIWAN, R. O. C.
Contact Person :
TRACY CHENG /
Equipment :
ADSL2+Wireless-G Router, ADSL2+Router with 4 Port Switch
Model No.:
AR-7064g+, AR-7064+
Traceability:
FCC Part 15 & Part 2; Docket 95-19
Limitation:
CISPR 22 CLASS B
Date of issued:
JAN.
Report No.:
E940705(A)
19,
ASSISTANT
2006
The device bearing the trade name and model specified above has been shown to comply with the
applicable technical standards as indicated in the measurement report and was tested in accordance
with the measurement procedures specified in ANSI C63.4-2001. (See Test Report if any
modifications were made for compliance.)
PEP certifies that no party to this application has been denied the NVLAP benefits pursuant to
Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a).
M. Y. Tsui /NVLAP Signatory
NVLAP LAB CODE: 200097-0
DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Responsible Party:
EDIMAX TECHNOLOGY CO., LTD.
Address:
NO. 3, WU CHUAN 3RD ROAD, WU-KU INDUSTRIAL PARK,
TAIPEI HSIEN, TAIWAN, R. O. C.
Contact Person:
TRACY CHENG /
ASSISTANT
Phone
886-2-22995648
Fax
No.:
Equipment
:
Model No. :
No.:
886-2-22995647
ADSL2+Wireless-G Router, ADSL2+Router with 4 Port Switch
AR-7064g+, AR-7064+
We hereby declare that the equipment bearing the trade name and model number
specified above was tested conforming to the applicable FCC Rules under the
most accurate measurement standards possible, and that all the necessary steps
have been taken and are in force to assure that production units of the same
equipment will continue to comply with the Commission s requirements.ġ
ġ
ġ
ġ
ġ
ġ
ġ
ġ
ġ
ġ
ġ
ġ
Signature
ġ
ġ
Date
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising