Elation 36 Specifications

Elation 36 Specifications
Design LED 36 TRI Brick
Elation Professional™
6122 S. Eastern Ave.
Los Angeles, Ca 90040
www.elationlighting.com
Rev. 12/12/2008 – visage
Software Ver. 3.1
DESIGN LED 36 TRIBRICK™
TABLE OF CONTENS
1.
General Information……………………………………………………………………… 2
a. Introduction………………………………………………………………………. 2
b. Unpacking………………………………………………………..…...………..… 2
c.
Customer Support…………………………………………….………………… 2
d. Warranty Registration……………………………………………….……..…… 3
2.
Safety Instructions………………………………………………………........…………. 4
3.
Features…………………………………………………………………………………… 6
4.
General Guidelines………………………………………………………………………. 7
5.
Fixture Overview…………………………………………………………………………. 8
6.
Mounting and Installation…………………………………………………….…….……. 10
a. Yoke Assembly…………………………………………………….…………….. 10
b. Mounting Positions……………………………………………….………………12
c.
Mounting Points…………………………………………………………………. 13
d. Clamp Mounting…………………………………………………………………. 14
e. Securing………………………………………………………………………….. 14
7.
Understanding DMX……………………………………………………………………... 15
a. DMX Connections………………………………………………………………. 16
b. DMX Terminator…………………………………………………………………. 17
c.
3-Pin to 5-Pin Conversion………………………………………………………. 17
d. Fixture DMX Addressing.……………………………..………………………… 17
8.
Display LED Indicators..………………………………………………………………… 19
9.
Fixture Menu..…………………………………………………………………………… 20
10. DMX Traits………………………………………………………………………………… 22
a. 3-Channel Mode………………………………………………………………… 22
b. 4-Channel Mode…..…………………………………………………………..… 23
c.
6-Channel Mode…………………………………………………………………. 24
d. 12-Channel Mode…..…………………………………………………………… 26
e. 15-Channel Mode…..…………………………………………………………… 28
11. Lens Replacement……… ……………………………………………………………… 31
12. Cleaning and Maintenance……………………………………………………………… 32
13. Warranty…………………………………………………………………………………... 33
14. Photometric Data………………………………………………………………………… 35
15. Dimensional Drawings………………………………………………….……………….. 36
16. Circuit Schematic………...………………………………………………………………. 37
17. Technical Specifications…………………………………………...………….………… 38
©Elation Professional, Los Angeles Ca.
1
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and
reliable LED fixtures on the market today! The Design LED Tri Brick,™ has been designed to
perform reliably for years when the guidelines in this booklet are followed. Please read and
understand the instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information regarding safety during
use and maintenance.
UNPACKING: Thank you for purchasing the Design LED Tri Brick™ by Elation
Professional®. Every Design LED Tri Brick™ has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping carton for damage that
may have occurred during shipping. If the carton appears to be damaged, carefully inspect
your fixture for damage and be sure all accessories necessary to operate the fixture have
arrived intact. In the event damage has been found or parts are missing, please contact our
customer support team for further instructions. Inside the box you should find: the fixture, a
DMX XLR cable, a safety cable, and this manual. Please do not return this unit to your
dealer without first contacting customer support at the number listed below.
CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to provide
set up help and to answer any question should you encounter problems during your set up
or initial operation. You may also visit us on the web at www.elationlighting.com for any
comments or suggestions. For service related issue please contact Elation Professional®.
Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice:
(323) 582-3322
Fax:
(323) 832-9142
E-mail:
[email protected]
Forum:
www.ElationLighting.com/forum
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to
rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
©Elation Professional, Los Angeles Ca.
2
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
yourself. Doing so will void your manufactures warranty.
Please do not discard the shipping carton in the trash. Please recycle whenever possible.
WARRANTY REGISTRATION: The Design LED Tri Brick™ carries a two year (730 days)
limited warranty. Please fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written
on the outside of the return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included in the shipping
container. If the unit is under warranty, you must provide a copy of your proof of purchase
invoice. Items returned without a R.A. number clearly marked on the outside of the package
will be refused and returned at customer’s expense. You may obtain a R.A. number by
contacting customer support at (323) 582-3322.
©Elation Professional, Los Angeles Ca.
3
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
2. SAFETY INSTRUCTIONS
To guarantee proper and consistent operation, it is important to
follow the guidelines in this manual. Elation Professional will not
accept responsibility for damages resulting from the misuse of
this fixture due to the disregard of the information printed in this
manual.
1. Always be sure that the fan and the air inlets remain clean and are never
blocked. Allow about 6” (15cm) between this fixture and other devices or a wall
to allow for proper cooling.
2. Never touch the fixture during normal operation.
3. Never look directly into the light source. You risk injury to your retina, which may
induce blindness.
4. For safe operation, follow the Installation guide described in chapter two of this
manual. Operating the Design LED 36 Tri Brick™ without suited safety aids
such as safety cables or clamps can increase the risk of damage and/or
personal injury.
5. Qualified and certified personnel should only perform installation.
6. When mounting this fixture, use only the original rigging points included with this
fixture. Any structural modification will void the original manufactures warranty
and may increase the risk of damage and/or personal injury.
7. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.
8. Do not attempt to operate this fixture if the power cord has become damaged or
frayed.
9. Never open this fixture while in use.
10. This device falls under protection-class I. Therefore it is essential that the device
be grounded properly.
11. Qualified personnel should perform all electrical connections.
12. Be sure the available voltage matches the voltage requirements of the unit. Be
©Elation Professional, Los Angeles Ca.
4
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
sure the power cord is never crimped or damaged. If the power cord is damaged,
replace it immediately with a new one of similar power rating.
13. Always disconnect from main power before performing any type of service or
any cleaning procedure.
14. Only handle the power cord by the plug. Never pull out the plug by tugging the
wire portion of the cord.
15. Please be aware that damages caused by modifications to the device are
not subject to warranty.
Important Notice: Damages resulting from the disregard of safety and general user
instructions found in this user manual are not subject to any warranty claims.
©Elation Professional, Los Angeles Ca.
5
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
3. FEATURES
•
Low power consumption
•
Minimal heat emission
•
Maintenance free operation
•
Equipped with 12 1-Watt Tri-Color LEDs (36 LEDs Total)
•
No Tri-Color Shadows
•
High power LEDs manufactured by Lumileds, USA
•
100,000 hours rated LED life
•
Seamless RGB color changing
•
USITT DMX-512 Complaint
•
Preprogrammed colored macros
•
Strobe-effect with a maximum flash rate of 18fps
•
DMX-controlled operation or stand-alone operation with Master/Slave-function
•
8 built-in programs can be called up via DMX-controller
~ 48 preprogrammed scenes per a program
•
Sound-controlled via built-in microphone
•
Five DMX Control Modes:
15 DMX channels
12 DMX channels
6 DMX channels
4 DMX channels
3 DMX channels
•
DMX-control via standard DMX-controller
•
3-pin and 5-pin DMX connectors
•
Flicker-free operation for television and film
•
Compact design: fits in 12” box truss
•
Brilliant light output
©Elation Professional, Los Angeles Ca.
6
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
4. GENERAL GUIDELINES
This fixture is a professional lighting effect designed for use on stage, in nightclubs, in
theatres, and other types of architectural installations. Do not attempt operation or
installation without a proper knowledge on how to do so.
This fixture was designed for indoor use only; use of this fixture outside will void the
manufacture’s warranty.
Consistent operational breaks will ensure that the fixture will function properly for many
years to come.
Do not shake the fixture around. Avoid brute force when installing or operating the fixture.
While choosing an installation location, please be sure that the fixture will not be exposed to
extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or flat
surface should be at least 0.5 meter (about 1.5ft).
Always install the fixture with an appropriately rated safety cable. When installing the fixture
in a suspended environment always be sure to use mounting hardware no less than M10 x
25 mm, also be sure the hardware is only inserted in the yoke’s mounting holes.
Do not attempt to operate this fixture until you have familiarized yourself with all of its
functions.
Do not permit operation by persons not qualified for operating this type of theatrical fixture.
Most damages are the result of improper operation.
Please use the original packaging to transport the fixture in for service.
For your own safety, please read this user manual carefully before installing the device.
©Elation Professional, Los Angeles Ca.
7
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
5. FIXTURE OVERVIEW
1. LED Lens Assembly – The lens assembly may be user replaced in the event repair
is needed or a different beam angle is required.
2. Lens Cover – This cover holds the lens assemblies in place and is easily removed.
3. Hanging Bracket Locking Knob – This knob is used to secure the hanging bracket
in to place.
4. On/Off Power Switch – Controls main power to the unit.
5. Power Output Jack – Use this jack to jump power to another Design LED 36
©Elation Professional, Los Angeles Ca.
8
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
TriBrick™ in an array system.
6. Power Input/Fuse Holder Assembly – This assembly holds the safety fuse and
provides a female IEC connector for power. If needed, always replace fuse with an
exact match unless otherwise specified by an Elation Service Technician. Using a
fuse other than that specified could damage the unit and will void your warranty.
7. Eyebolt – Use this bold as a safety-cable rigging point. Always secure any
installation with a properly rated safety-cable.
8. Menu Button – This button is used to access the fixtures menu functions.
9. Up Button – The up button is used to toggle forward through the menu functions and
settings.
10. Down Button – The down button is used to toggle backwards through the menu
functions and settings.
11. Enter Button – The enter button is used to enter in to a certain menu function or to
lock a menu setting in to memory.
12. LED Display – 4-segment menu display. Used to display the DMX address as well
as all other menu functions.
13. 5-pin DMX In Jack – This jack accepts an incoming DMX signal via a male, 5-pin
XLR jack.
14. 5-pin DMX Out Jack – This jack is used to send an incoming DMX signal to the next
fixture in the DMX chain via a female, 5-pin XLR jack.
15. 3-pin DMX Out Jack – This jack is used to send an incoming DMX signal to the next
fixture in the DMX chain via a female, 3-pin XLR jack.
16. 3-Pin DMX In Jack – This jack accepts an incoming DMX signal via a male, 3-pin
XLR jack.
©Elation Professional, Los Angeles Ca.
9
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
6. MOUNTING AND INSTALLATION
Yoke Assembly – Single Unit Operation
The device can be placed directly on the stage floor or rigged in any orientation on a truss
without altering its operation characteristics. When connecting the hanging yoke to the
fixture, refer to the illustration below.
Yoke Assembly – Multiple Unit Operation
You can connect up to four Design LED Tri Bricks together in a bar assembly. To connect
multiple units together use the included mounting hardware and refer to the diagram below.
©Elation Professional, Los Angeles Ca.
10
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
Please note: To ensure maximum stability, no more than for units should be mounted
together in this fashion. Connecting more than four units will result in an unstable
assembly, which could collapse and damage the units.
Cautions:
For added protection mount the fixtures in areas outside walking paths, seating areas, and
away from areas were the fixture might be reached by unauthorized personal.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
To avoid injury, never stand directly below the device when mounting, removing, or servicing
the fixture.
Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE0711-217
for proper installation in Europe To ensure proper installation, only
qualified staff should attempt installation.
Mounting points
Overhead mounting requires extensive experience, including amongst others calculating
working load limits, a fine knowledge of the installation material being used, and periodic
safety inspection of all installation material and the fixture. If you lack these qualifications, do
not attempt the installation yourself. Improper installation can result in bodily injury.
CAUTION!
Be sure a qualified electrician performs all electrical
connections.
Be sure to complete all rigging and installation procedures before connecting the main
©Elation Professional, Los Angeles Ca.
11
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
power cord to the appropriate wall outlet.
Mounting
The Design LED Tri Brick™ is fully operational in any mounting position, hanging
upside-down from a ceiling, side mounted, or set on a flat level surface, etc. Be sure this
fixture is kept at least 0.5m away from any flammable materials (decoration etc.). When
clamp mounting; always use and install the supplied safety cable as an added safety
measure to prevent accidental damage in the event of a clamp failure. See the image
below.
Clamp Mounting
The Design LED Tri Brick™ provides a unique mounting bracket assembly that allows the
unit to stand on flat surface, hang on truss via a clamp, or be used in cluster allow multiple
©Elation Professional, Los Angeles Ca.
12
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
units to rigged together (see the illustration below). Regardless of the mounting option you
choose please refer to the safety guidelines in this manual to avoid damage to the unit
and/or injury to persons.
When mounting this fixture to truss be sure to secure an appropriately rated clamp to the
hanging yoke using a M10 screw fitted through the center hole of the hanging yoke. As an
added safety measure be sure to attach at least one properly rated safety cable to the fixture.
See illustrations below.
©Elation Professional, Los Angeles Ca.
13
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
Securing the Design LED Tri Brick™
Always be sure to secure your fixture with a safety cable when
suspending the unit from truss or other means. The fixture
provides a built-in rigging point for a safety cable as illustrated
above. Be sure to only use the designated rigging point for the
safety cable and never secure a safety cable to the hanging
bracket.
©Elation Professional, Los Angeles Ca.
14
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
7. UNDERSTANDING DMX
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by lighting and
controller manufactures as a form of communication between intelligent fixtures and
controllers. DMX allows all makes and models of different manufactures to be linked
together and operate from a single controller. This is possible as long as all the fixtures and
the controller are DMX compliant. A DMX controller sends the DMX data instructions to a
fixture allowing the user to control the different aspects of an intelligent light. DMX data is
sent out as serial data that travels from fixture to fixture via data “IN” and “OUT” XLR
terminals located on the fixtures (most controllers will only have output jacks).
DMX Linking: To ensure proper DMX data transmission, always use proper DMX cables
and a terminator, never use microphone cables. When using several DMX fixtures try to use
the shortest cable path possible. Never split a DMX line with a “Y” style connector. The order
in which the fixtures are connected in a DMX line does not influence the DMX addressing.
For example; a fixture assigned a DMX address of 1 may be placed anywhere in the DMX
chain, at the beginning, at the end, or anywhere in the middle. The DMX controller knows to
send data assigned to address 1 to that fixture no matter where it is located in the DMX
chain. The Design LED 36 TriBrick™ can be controlled via DMX-512 protocol. The Design
LED 36 TriBrick™ is a fixture that can operate in five different DMX modes; 3, 5, 6, 12, or 15
channels (see page 22 for the different DMX operations). The DMX address is set
electronically using the controls on the LED menu.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): Your
fixture and your DMX controller require a standard 3-pin or 5-pin XLR connector for data
input and data output (the illustration on the next page is of a 3-Pin XLR connector). If you
are making your own cables, be sure to use two conductor shielded digital DMX cable rated
at 120 ohms, this cable is designed for DMX transmission and may be purchased from your
Elation dealer or at most professional lighting retailers. Your cables should be made with a
male and female XLR connector on either end of the cable. Also, remember that a DMX line
must be daisy chained and cannot be split, unless using an approved DMX splitter such as
the Elation Opto Branch 4™ or DMX Branch/4™.
©Elation Professional, Los Angeles Ca.
15
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
Be sure to follow the above figure when making your own cables. Do not use the ground lug
on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or
allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the
shield could cause a short circuit and erratic behavior.
DMX-512 control connection
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the
other side to the male 3-pin XLR input of the fixture (Please refer to the diagram below.). You
can chain multiple fixtures together through serial linking. The cable needed should be two
conductor, shielded cable with XLR input and output connectors. Always be sure daisy chain
your in and out data connections, never split or “Y” your DMX connections unless you are
using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX Branch/4™.
©Elation Professional, Los Angeles Ca.
16
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
DMX-512 connection with DMX terminator
A DMX terminator should be used in all DMX lines especially in longer runs. The use of a
terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt
resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA
-). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain
to terminate the line. Using a line terminator (Elation part: DMX T PACK) will decrease the
possibilities of erratic behavior.
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA
transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX
line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must
be used, these adaptors are readily available at most electric stores. The following chart
details a proper cable conversion.
Fixture DMX addressing;
All fixtures should be given a DMX starting address when using a DMX controller, so the
correct fixture responds to the correct control signal. This digital starting address is the
©Elation Professional, Los Angeles Ca.
17
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
channel number from which the fixture starts to “listen” to the digital control information sent
out from the DMX controller. The allocation of this starting DMX address is achieved by
setting the correct DMX address on the digital display located on the back of the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set different
address for each individual fixture. Be advised that setting all you fixtures to the same DMX
address will subsequently control all fixtures in the same fashion, in other words, changing
the settings of one channel will affect all the fixtures simultaneously.
If you set each fixture to a different DMX address, each unit will start to “listen” to the
channel number you have set, based on the quantity of control channels (DMX channels) of
each fixture. That means changing the settings of one channel will only affect the selected
fixture.
In the case of the Design LED 36 TriBrick™, which is up to a 15 channel fixture, you should
set the starting DMX address of the first unit to 1, the second unit to 16 (15 + 1), the third unit
to 31 (15 + 16), and so on.
Note: During start-up the Design LED 36 TriBrick™ will automatically detect whether a DMX
data signal is being received or not. If a DMX data signal is being received, the display will
show "A.XXX" (XXX representing the actual DMX address). If the fixture is not receiving a
DMX signal the display will flash "A.XXX" (XXX representing the actual DMX address).
If your fixture is connected to a DMX controller and the display is flashing (not receiving a
DMX signal), please check the following:
-
The 3-pin or 5-pin XLR plug (cable with DMX signal from controller) may not be
connected or is not inserted completely into the DMX input jack.
-
The DMX controller is switched off or defective.
-
The DMX cable or connector is defective.
-
A DMX terminator has been inserted into the last fixture in your DMX chain.
©Elation Professional, Los Angeles Ca.
18
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
8. DISPLAY LED INDICATORS.
The Design LED 36 TriBrick has two LED indicators on the display. These indicators are
designed to give a quick visual indication of the fixtures’ status. The illustration below details
the functionality of the LED indicators.
. .
DMX OK
.
.
NO DMX
Lamp on
Lamp on
NO DMX
Lamp off
DMX OK
Lamp off
The first LED indicators represents DMX signal:
•
If the indicators is on a clean DMX signal is present
•
If the indicator is off there is no DMX signal present
The second LED indicator represents lamp condition; this is only applicable to fixtures with
traditional lamp sources.
©Elation Professional, Los Angeles Ca.
19
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
9. DISPLAY MENU
Default settings shaded.
MODE
ADDR
DISP
FLIP
CHAN
SLAV
CNTL
MANU
BLAC
Set the starting DMX address
Display “Blackout” function. When activated the display
ON/OFF
will automatically blackout when not in use.
ON/OFF
When “ON” this function rotate the display 180°
3 CH
3 DMX CHANNELS (RGB)
4 CH
4 DMX CHANNELS (RGB+MASTER DIM)
6 CH
6 DMX CHANNELS
Set 12 channel mode
12CH
15CH
Set 15 channel mode
ON/OFF
UNIT FUNCTIONS AS SLAVE
Fixture will function as a master unit in Master/Slave
MAST
mode
Fixture will function “Stand Alone” mode
ALON
BLACKOUT – All LEDs off
Manual Mode - Manual setting of RED levels
RED
RXXX
AXXX (1-512)
GXXX
BLUE
BXXX
STRB
SXXX
SPED
XXX
Adjust program 1 speed
FADE
XXX
Adjust program 1 fade time
STRB
XXX
Adjust strobe rate of program 1
SPED
XXX
Adjust program 2 speed
FADE
XXX
Adjust program 2 fade time
STRB
XXX
Adjust strobe rate of program 2
SPED
XXX
Adjust program 3 speed
FADE
XXX
Adjust program 3 fade time
STRB
XXX
Adjust strobe rate of program 3
COLR
CHAS
CHS1
CHS2
CHS3
Manual Mode - Manual setting of GREEN levels
GREN
©Elation Professional, Los Angeles Ca.
Manual Mode - Manual setting of BLUE levels
Manual Mode - Manual setting of STROBE rate
20
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
CHS4
CHS5
CHS6
CHS7
CHS8
OTHR
DIMR
SPED
XXX
Adjust program 4 speed
FADE
XXX
Adjust program 4 fade time
STRB
XXX
Adjust strobe rate of program 4
SPED
XXX
Adjust program 5 speed
FADE
XXX
Adjust program 5 fade time
STRB
XXX
Adjust strobe rate of program 5
SPED
XXX
Adjust program 6 speed
FADE
XXX
Adjust program 6 fade time
STRB
XXX
Adjust strobe rate of program 6
SPED
XXX
Adjust program 7 speed
FADE
XXX
Adjust program 7 fade time
STRB
XXX
Adjust strobe rate of program 7
SPED
XXX
Adjust program 8 speed
FADE
XXX
Adjust program 8 fade time
STRB
XXX
Adjust strobe rate of program 8
MOD1
MOD2
LOAD
VER
V X.X
Default - Fixture will function with a stepping dimmer
rate.
Linear - Fixture will function with a smoother dimming
rate of 0~100%
Restores the factory default settings
“X.X’ will represent the fixture’s current firmware
version
Remarks:
1) If the fixture does not receive a DMX signal the menu display will flash
repeatedly.
2) SPED: Adjust the hold time for each scene in built-in chase programs.
3) FADE: Adjust the fade time between each scene in the built-in programs.
©Elation Professional, Los Angeles Ca.
21
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
10. DMX TRAITS
DMX Operation Notes:
The fixture will function in DMX mode whenever the unit is receiving a DMX signal. Please
note that this will override all manual settings.
This unit will keep and retain the last DMX command in the event of DMX signal failure. To
reset the fixture you must turn the power off.
DMX CHANNEL TRAITS
The charts below outline the different DMX traits for the 4 different DMX modes.
3-Channel mode: In this mode channel 1 controls all the red LEDs, channel 2 controls all
the green LEDs, and channels 3 controls all the blue LEDs.
CHANNEL 1:Red
CHANNEL 2:Green
CHANNEL 3:Blue
3 Channel Mode: The chart below details the DMX channel layout for 3-channel assignment.
DMX channel’s functions and their values (3 Channel Mode):
Channel 1
- Red:
0-255
Red (0-Black, 255 - 100% Red)
Channel 2
- Green:
0-255
Green (0-Black, 255 - 100% Green)
Channel 3 - Blue:
0-255
Blue (0-Black, 255 - 100% Blue)
©Elation Professional, Los Angeles Ca.
22
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
4-Channel mode: In this mode channel 1 controls all the red LEDs, channel 2 controls all
the green LEDs, channels 3 controls all the blue LEDs, and channel 4 will control the master
dimming level.
CHANNEL 1:Red
CHANNEL 2:Green
CHANNEL 3:Blue
CHANNEL 4:Dimmer/Speed
4 Channel Mode: The chart below details the DMX channel layout for 4-channel assignment.
DMX channel’s functions and their values (4 Channel Mode):
Channel 1
- Red:
0-255 Red (0-Black, 255 - 100% Red)
Channel 2
- Green:
0-255 Green (0-Black, 255 - 100% Green)
Channel 3 - Blue:
0-255 Blue (0-Black, 255 - 100% Blue)
Channel 4 - Dimming / Program Speed Control
This channel has two functions depending on the operating mode. When running the built-in
programs this channel will control the program
speed.
0-255 Dimming (0%-100%) ~ Normal Operation
0-255 Speed (min to max) ~ When running built-in programs on channel 4
©Elation Professional, Los Angeles Ca.
23
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
6 Channel Mode: This chart details a simple layout of the DMX channel assignment in
CHANNEL 1: Red
CHANNEL 2: Green
CHANNEL 3: Blue
CHANNEL 4: Auto Programs (Built-in Programs)
CHANNEL 5: Strobe
CHANNEL 6: Dimmer/Speed
DMX channel’s functions and their values (6 Channel Mode):
Channel 1 - Red:
0-255
Red (0-Black, 255-100% Red)
Channel 2 - Green:
0-255
Green (0-Black, 255- 100% Green)
Channel 3 - Blue:
221-255
Blue (0-Black, 255- 100% Blue)
Channel 4 - Internal programs:
0-10
No function
11-40
Internal program 1
41-70
Internal program 2
71-100
Internal program 3
101-130
Internal program 4
131-160
Internal program 5
161-190
Internal program 6
191-220
Internal program 7
221-255
Internal program 8
Channel 5 - Strobe:
0
No function
©Elation Professional, Los Angeles Ca.
24
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
1~95
Strobe effect slow to fast
96-127
No function
128-159
Pulse effect in sequences
160-191
No function
192-223
Random strobe effect slow to fast
224-255
No function
Channel 6 - General dimming / Program Speed Control
This channel has two functions depending on the operating mode. When running the built-in
programs this channel will control the program speed, when not running the built-in programs
this channel will control master dimming.
0-255
Dimming (0%-100%) ~ Normal Operation
0-255
Speed (min to max) ~ When running built-in programs on channel 4
©Elation Professional, Los Angeles Ca.
25
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
12-Channel mode: In this mode all channels are used to control the various RGB LEDs.
CHANNEL 1:Red
CHANNEL 2:Green
CHANNEL 3:Blue
CHANNEL 4:Red
CHANNEL 5:Green
CHANNEL 6:Blue
CHANNEL 7:Red
CHANNEL 8:Green
CHANNEL 9:Blue
CHANNEL 10:Red
CHANNEL 11:Green
CHANNEL 12:Blue
12 Channel Mode: The chart below details the DMX channel layout for 12-channel
assignment.
DMX channel’s functions and their values (12 Channel Mode):
Channel 1 - Red:
0-255
Red (0-Black, 255-100% Red)
Channel 2 - Green:
0-255
Green (0-Black, 255- 100% Green)
Channel 3 - Blue:
221-255
Blue (0-Black, 255- 100% Blue)
Channel 4 - Red:
0-255
Red (0-Black, 255-100% Red)
Channel 5 - Green:
©Elation Professional, Los Angeles Ca.
26
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
0-255
Green (0-Black, 255- 100% Green)
Channel 6 - Blue:
221-255
Blue (0-Black, 255- 100% Blue)
Channel 7 - Red:
0-255
Red (0-Black, 255-100% Red)
Channel 8 - Green:
0-255
Green (0-Black, 255- 100% Green)
Channel 9 - Blue:
221-255
Blue (0-Black, 255- 100% Blue)
Channel 10 - Red:
0-255
Red (0-Black, 255-100% Red)
Channel 11 - Green:
0-255
Green (0-Black, 255- 100% Green)
Channel 12 - Blue:
221-255
Blue (0-Black, 255- 100% Blue)
©Elation Professional, Los Angeles Ca.
27
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
15-Channel mode: In this mode channels 1~12 are used to control the various RGB LEDs
and channels 13~15 will control special features.
CHANNEL 1:Red
CHANNEL 2:Green
CHANNEL 3:Blue
CHANNEL 4:Red
CHANNEL 5:Green
CHANNEL 6:Blue
CHANNEL 7:Red
CHANNEL 8:Green
CHANNEL 9:Blue
CHANNEL 10:Red
CHANNEL 11:Green
CHANNEL 12:Blue
CHANNEL 13:Auto Programs (Built-in Programs)
CHANNEL 14:Strobe
CHANNEL 15:Dimmer/Speed
15 Channel Mode: The charts below and on the next page detail the DMX channel layout for
15-channel assignment.
©Elation Professional, Los Angeles Ca.
28
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
DMX channel’s functions and their values (15 Channel Mode):
Channel 1
0-255
Channel 2
0-255
- Red:
Red (0-Black, 255-100% Red)
- Green:
Green (0-Black, 255- 100% Green)
Channel 3 - Blue:
0-255
Channel 4
0-255
Channel 5
0-255
Blue (0-Black, 255- 100% Blue)
- Red:
Red (0-Black, 255-100% Red)
- Green:
Green (0-Black, 255- 100% Green)
Channel 6 - Blue:
0-255
Channel 7
0-255
Channel 8
0-255
Blue (0-Black, 255- 100% Blue)
- Red:
Red (0-Black, 255-100% Red)
- Green:
Green (0-Black, 255- 100% Green)
Channel 9 - Blue:
0-255
Blue (0-Black, 255- 100% Blue)
Channel 10
- Red:
0-255
Red (0-Black, 255-100% Red)
©Elation Professional, Los Angeles Ca.
29
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
Channel 11
- Green:
0-255
Green (0-Black, 255- 100% Green)
Channel 12 - Blue:
0-255
Blue (0-Black, 255- 100% Blue)
Channel 13 - Internal programs:
0-10
No function
11-40
Internal program 1
41-70
Internal program 2
71-100
Internal program 3
101-130
Internal program 4
131-160
Internal program 5
161-190
Internal program 6
191-220
Internal program 7
221-255
Internal program 8
Channel 14
- Strobe:
0
No function
1~95
Strobe effect slow to fast
96-127
No function
128-159
Pulse effect in sequences
160-191
No function
192-223
Random strobe effect slow to fast
224-255
No function
Channel 15 - General dimming / Program Speed Control
This channel has two functions depending on the operating mode. When running the built-in
programs this channel will control the program speed, when not running the built-in programs
this channel will control master dimming.
0-255
Dimming (0%-100%) ~ Normal Operation
0-255
Speed (min to max) ~ When running built-in programs on channel 4
©Elation Professional, Los Angeles Ca.
30
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
11. LENS REPLACEMENT
The Design LED Tri Brick comes with a removable front cover that allows lens assembly to
be changed out to achieve different beam angles.
The lens cover is held in place by two ¼ turn locking fasteners. To remove the cover; 1) Turn
the locking fasteners in a counter-clockwise direction. 2) Once the fasteners are loose lift the
cover straight up to access the four individual lenses (see first illustration below). 3) Locate
the 8 securing screws on the inner cover and remove them. 4) Remove the inner cover to
access the lenses (see second illustration below). Once the lenses are changed reassemble
in reverse order.
©Elation Professional, Los Angeles Ca.
31
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
12. CLEANING AND MAINTENANCE
Consider the following points during normal service and inspection:
1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may
fall out during normal operation resulting in damage or injury as larger parts could fall.
2. Electric power supply cables must not show any damage, material fatigue or
sediments. Never remove the ground prong from the power cable.
Further instructions depending on the installation spot and usage have to be adhered by a
skilled installer and any safety problems have to be removed.
Disconnect from mains before starting maintenance operation.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never
use alcohol or solvents.
There are no user serviceable parts inside this fixture, please refer all other service issues to
an authorized Elation service technician.
Should you need any spare parts, please order genuine parts from your local dealer.
©Elation Professional, Los Angeles Ca.
32
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
13.
A.
2-YEAR LIMITED WARRANTY
Elation Professional® hereby warrants, to the original purchaser, Elation Professional®
products to be free of manufacturing defects in material and workmanship for a period of two
years, (730 days) from the date of purchase. This warranty shall be valid only if the product
is purchased within the United States of America, including possessions and territories. It is
the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B.
For warranty service, send the product only to the Elation Professional® factory. All
shipping charges must be pre-paid. If the requested repairs or service (including parts
replacement) are within the terms of this warranty, Elation Professional® will pay return
shipping charges only to a designated point within the United States. If the entire instrument
is sent, it must be shipped in its original package. No accessories should be shipped with the
product. If any accessories are shipped with the product, Elation Professional® shall have no
liability what so ever for loss of or damage to any such accessories, nor for the safe return
thereof.
C.
This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which Elation Professional® concludes, after inspection, affects the
reliability of the product; if the product has been repaired or serviced by anyone other than
the Elation Professional® factory unless prior written authorization was issued to purchaser
by Elation Professional®; if the product is damaged because not properly maintained as set
forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, Elation Professional® will replace
defective parts at its expense, and will absorb all expenses for warranty service and repair
labor by reason of defects in material or workmanship.
The sole responsibility of Elation
Professional® under this warranty shall be limited to the repair of the product, or replacement
thereof, including parts, at the sole discretion of Elation Professional®. All products covered
by this warranty were manufactured after January 1, 1990, and bare identifying marks to that
©Elation Professional, Los Angeles Ca.
33
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
effect.
E.
Elation Professional® reserves the right to make changes in design and/or
improvements upon its products without any obligation to include these changes in any
products theretofore manufactured.
F.
No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by
applicable law, all implied warranties made by Elation Professional® in connection with this
product, including warranties of merchantability or fitness, are limited in duration to the
warranty period set forth above. And no warranties, whether expressed or implied, including
warranties of merchantability or fitness, shall apply to this product after said period has
expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as
is expressly provided above; and under no circumstances shall Elation Professional® be
liable for any loss or damage, direct or consequential, arising out of the use of, or inability to
use, this product.
G.
This warranty is the only written warranty applicable to Elation Professional® Products
and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
©Elation Professional, Los Angeles Ca.
34
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
14.
PHOTOMETRIC DATA
©Elation Professional, Los Angeles Ca.
35
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
15.
DIMENSIONAL DRAWINGS
©Elation Professional, Los Angeles Ca.
36
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
16.
CIRCUIT SCHEMATIC
©Elation Professional, Los Angeles Ca.
37
www.ElationLighting.com
DESIGN LED 36 TRIBRICK™
17.
TECHNICAL SPECIFICATIONS
Power supply:
100v~240v / 50Hz~60Hz AC
Power consumption:
MAXIMUM 65W
LED Configuration:
12 Tri-Color, 1Watt SMDs / 36 1-Watt Total
IP Rating:
IP20
Weight:
4.3 Kgs / 9.5Lbs
DMX Channels:
15, 12, 6, 4, or 3 Channel mode
DMX Drive:
Standard DMX-512,
3 pole XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1.
5 pole XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1.
Pins 4 & 5 are not applicable
Color Mixing:
RGB Color Additive Mixing
Beam Angle:
38.5˚
Fuse:
GMA 220v~2A
Dimmer:
Continuous Dimming 0~100%
Strobe:
Electronic Strobe 0~18
Lamp Life:
100,000 Hours Rated Life
Dimensions:
(41.5 x 23 x 8)cm
Fps
16.3” x 9” x 3.15”
Please Note: Specifications and improvements in the design of this unit and this manual are
subject to change without any prior written notice.
©Elation Professional, Los Angeles Ca.
38
www.ElationLighting.com
Elation Professional
6122 S. Eastern Ave.
Los Angeles, CA. 90040
323-582-3322 / 323-832-9142 fax
www.ElationLighting.com /
[email protected]
Rev. 12/12/2008 – visage
Software Ver. 3.1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement