KSP-ME LOW FREQUENCY TRANSMITTER INSTALLATION BEFORE USE ....

KSP-ME LOW FREQUENCY TRANSMITTER INSTALLATION BEFORE USE ....
KSP-ME
INSTRUCTION MANUAL
LOW FREQUENCY TRANSMITTER
BEFORE USE ....
Thank you for choosing M-System. Before use, check the
package you received as below.
If you have any problems or questions with the product,
please contact M-System's Sales Office or representatives.
n PACKAGE INCLUDES:
Signal conditioner (body + base socket)...................(1)
n MODEL NO.
Check that model No. described on specification label is
exactly what you ordered.
n INSTRUCTION MANUAL
This manual describes necessary points of caution when you
use this product, installation, connection and basic maintenance procedures.
INSTALLATION
Detach the yellow clamps located at the top and bottom of the
unit for separating the body from the base socket.
n DIN RAIL MOUNTING
Set the base socket so that
its DIN rail adaptor is at
the bottom. Position the
upper hook at the rear
side of base socket on the
DIN rail and push in the
lower. When removing
the socket, push down the
DIN rail adaptor utilizing
a screwdriver (–) and pull.
Specification
Zero Adj.
Span Adj.
Base Socket
Clamp
(top & bottom)
DIN Rail
35mm wide
Spring Loaded
DIN Rail Adaptor
n WALL MOUNTING
Refer to the drawings in
Shape and size of the base socket
the following page.
are slightly different with various
socket types.
COMPONENT IDENTIFICATION
Body
KSP-ME
MODEL
(50 Hz minimum, for Mitsubishi inverter)
TERMINAL CONNECTIONS
Connect the unit as in the diagram below or refer to the connection diagram label on the front of the unit.
K-UNIT
INPUT
+ 3
1 +
– 4
2 –
OUTPUT
7 U(+)
8 V(–)
POWER
Note) Do NOT connect other devices except the transmitter
to the inverter's FM terminal.
Do NOT bundle the FM and motor wirings.
EM-3572_ME Rev.1
P. 1 / 2
KSP-ME
POINTS OF CAUTION
CHECKING
1) Terminal wiring: Check that all cables are correctly connected according to the connection diagram.
2) Power input voltage: Check voltage across the terminal
7 – 8 with a multimeter.
3) Input: Check input terminal 3 (+) – 4 (–) with an oscilloscope.
Confirm the pulse width is of 50%±30 of the 100%. input
duty ratio. Signal level must be greater than 4.7V for
H. level and lower than 0.3 for L. level. Frequency must
be within the described specification on the label.
4) Output: Check that the load resistance meets the described
specifications.
ADJUSTMENT PROCEDURE
This unit is calibrated at the factory to meet the ordered specifications, therefore you usually do not need any calibration.
For matching the signal to a receiving instrument or in case
of regular calibration, adjust the output as explained in the
following.
n HOW TO CALIBRATE THE OUTPUT SIGNAL
Use a signal source and measuring instruments of sufficient
accuracy level. Turn the power supply on and warm up for
more than 10 minutes.
1) ZERO: Apply 10% input and adjust output to 10%.
2) SPAN: Apply 100% input and adjust output to 100%.
3) Check ZERO adjustment again with 10% input.
4) When ZERO value is changed, repeat the above procedure
1) – 3).
EXTERNAL DIMENSIONS
n GENERAL
• Before you remove the unit from its base socket or mount
it, turn off the power supply and input signal for safety.
n ENVIRONMENT
• When heavy dust or metal particles are present in the air,
install the unit inside proper housing and ventilate it.
• Do not install the unit where it is subjected to continuous
vibration. Do not apply physical impact to the unit.
• Environmental temperature must be within -5 to +55°C
(23 to 131°F) with relative humidity within 30 to 90% RH in
order to ensure adequate life span and operation.
n WIRING
• Do not install cables (power supply, input and output) close
to noise sources (relay drive cable, high frequency line, etc.).
• Do not bind these cables together with those in which noises
are present. Do not install them in the same duct.
n AND ....
• The unit is designed to function as soon as power is supplied,
however, a warm up for 10 minutes is required for satisfying
complete performance described in the data sheet.
MAINTENANCE
Regular calibration procedure is explained below:
n CALIBRATION
Warm up the unit for at least 10 minutes. Apply 10%, 25%,
50%, 75% and 100% input signal. Check that the output
signal for the respective input signal remains within accuracy
described in the data sheet. When the output is out of tolerance, recalibrate the unit according to the "ADJUSTMENT
PROCEDURE" explained earlier.
mm (inch)
CLAMP
(top & bottom)
20
(.79)
7.8 (.31)
50 (1.97)
123 (4.84)
[3.3 (.13)]
5
4
3
7
8
1
2
2–4.5 (.18) dia.
MTG HOLE
15 (.59) deep
8–M3.5
SCREW
103 (4.06)
6
80 (3.15)
80 (3.15)
35.4 (1.39)
DIN RAIL
35mm wide
40 (1.57)
50 (1.97)
• When mounting, no extra space is needed between units.
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such
product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System’s sole liability, and purchaser’s exclusive
remedies, under this warranty are, at M-System’s option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this
warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original
sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]
EM-3572_ME Rev.1
P. 2 / 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement