Starting Guide - Poseidon 3265
Poseidon 3265 – starting guide
HW group
Poseidon 3265
Starting Guide - Poseidon 3265
First steps for remote monitoring with Poseidon & GSM
1) Connecting Poseidon 3265
1.1) Check DIP switches settings. For installation keep them as
shown on the picture on the right (DIP1=Off, DIP2=Off).
1.2) RS-232 serial port for connecting GSM modem and setup
purposes.
1.3) Connect power adapter to power supply (230 /
110V) and to power jack of Poseidon. The connector
must be plugged in fully, green LED lights up.


1.4) Connect temperature or humidity sensor to IT bus
(Temp-1Wire or Humid-1Wire - RJ12 connector), the
connector must click.
1.5) Connect Poseidon to Ethernet (use direct
cable to Switch, cross-over cable to PC)
Green POWER LED on RJ45 connector lights up – power supply is OK
Yellow LED on the RJ45 connector blinks – connection to 10 Mbit network is OK
Accessories
GSM Modemcom G10
600 312
Poseidon T-Box
600 040
HTemp-Rack19
600 330
Temp-1Wire 1m
600 242
Humid-1Wire 3m
600 279
600 165
Poseidon 3265
Poseidon model 3265 unit with 5 sensors and GSM modem support
600 313
Poseidon 3265 GSM2 Tset
Start set - GSM modem, temperature sensors, power supply etc.
600 005
Temp-1Wire 3m
Temperature probe, 3m connecting cable (1m=600 242,10m=600 056)
600 311
Temp-1Wire-Outdoor 3m
Temperature probe for external use in food industry, cable 3m long
600 279
Humid-1Wire 3m
Humidity probe, extending cable 3m long(1m= 600 278)
600 040
Poseidon T-Box
Termination-Box for connecting up to 5 sensors, 10 cm long cable
600 280
Poseidon T-Box2
Termination-Box for connecting 2 sensors, 3m long cable
www.HW-group.com
600 166
Poseidon 3265 – starting guide
HW group
2) Configuring the IP address – UDP Config
UDP Config program – in the root folder of the supplied CD (Windows and Linux version).
The program can be
downloaded from
www.HW-group.com
Software -> UDP Config.
.
Click the icon to run
UDP Config – the
program
automatically
searches
for
connected devices
Click the Find
Devices button to
start searching for
devices.
The program looks for devices on your local
network. To identify a particular Poseidon unit, look
at its MAC address (printed on the label at the
bottom of the unit).
Double click a MAC address to open a dialog
window with basic device settings.
Set up network parameters
IP address
HTTP Port (default is 80)
Mask
Gateway IP address
Name of your device – optional
Click the Apply Changes button to save the
settings.
Note: Contact your network administrator if you
are unsure about these settings.
DIP1
DIP2
• Reset to factory defaults
Toggle DIP1 several times within 5 seconds after powering up. Default settings
contains none passwords.
• Disable any configuration changes (online demo mode)
While DIP2=On any configuration change disabled.
Note: Set Dip2=Off to be able change IP address configuration
www.HW-group.com
600 166
Poseidon 3265 – starting guide
HW group
3) Poseidon setting – Internet browser
3.1)
type device IP address into your web browser address bar or run UCP Config and click on
device IP address in the list of found devices
3.2)
Poseidon 3265 webpage
Device IP address
Contact unique ID
Monitored range of
each probe
Notification about
value out of range
You can change this
text, check manual..
Device name
„Flash setup“
detailed configuration
Display of SNMP MIB
and values.XML
Current Value – current value of the connected sensor. „-999.9“ means that the sensor is not available
or was initialized after device started.
Safe Range – Sensor value range that is not in Alarm.
Alarm Alert – Monitoring of the defined “Safe Range” exceeded or switch Dry contact input on/off
initiate Alarm state.
„For more information“– A contact to service organization, this can be changed from „Telnet setup“.
Reading current values
XML – values.xml file, format described using XSD – for download on the main page, detailed
comments on XML structure are available in the manual.
SNMP – description file poseidon.mib can be downloaded on the main page. Standard SNMP
ports 161 and 162 can be configured in Flash setup.
Modbus/TCP– structure description is available in the manual and in application examples.
Standard port 502 is opened for reading.
www.HW-group.com
600 166
Poseidon 3265 – starting guide
HW group
4) Flash Setup – probe detection
Click on “Flash Setup” from web page to open this graphics page.
Flash Setup requires Macromedia Flash player installed in web browser. If you do not have it, you
can download the latest version from Internet or find it on CD: \Poseidon\ install_flash_player_7.msi
Sensor detection: Tab „Sensors Setup“, click on “Autodetect Sensors”.
Using Flash setup you can:
Setup names of sensors, „Safe Range“ for alarm and to where the
Alarm alert will be sent.
Detect and configure GSM modem.
Monitor current values, refresh in seconds.
Select temperature units (°C, °F, °K)
Setup actual time and select NTP server to synchronize the time.
Setup SNMP parameters (Community names & rights) and define
where to send SNMP Traps.
Setup Alarm alert via email, and test it.
Setup security elements: Names and password, ranges of IP
addresses.
More information can be found in the manual or at www.HW-group.com
www.HW-group.com
600 166
Poseidon 3265 – starting guide
HW group
5) Connecting GSM modem
Following description is related to FW version 3.0.5 and higher. Latest FW can be downloaded from
the Poseidon XXXX page.
1. Deactivate PIN code protection of the SIM card.
If the function is active, the phone requires PIN code after start up.
2. Setup IP address and connect sensors to Poseidon 3265 according to previous procedure.
3. Connect GSM modem and Poseidon 3265 with supplied RS-232 cable.
4. Insert SIM card to modem slot.
5. Connect power supply to the GSM modem
6. Connect power supply to the Poseidon, wait for about 50 seconds for GSM modem activation.
Enable GSM modem
Send Test SMS when GSM
modem Ready
SMS Center number
detected automatically
from the SIM card, when
GSM modem Ready
7. Web browser opens FLASH Setup, tab "Email & SMS Setup" and verify if "Enabled" is
checked on "GSM SMS Interface" field.
o "RS-232 GSM module" should show "FOUND".
o "SMS centre" should show values from SIM card. If not, fill in your operator number.
8. Fill in "Alarm SMS Recipient 1" with target phone number where alarm is sent to and push
"SendTestSMS" button.
www.HW-group.com
600 166
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement