VOLTA VODVR 3204 User manual

VODVR 9000 Series DVR

Quick Operation Guide

User Manual of VODVR 9000 Series DVR

Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.

This manual is applicable to OPTIVA VODVR 9000 series DVR.

Verify Contents

Verify that the package contents are correct by checking the items against the packing list.

Note: Please contact your dealer for damaged or missing items.

DVR Pre-Installation

The 9000/9100 Series DVR is highly advanced surveillance equipment that should be installed with care. Please take into consideration the following precautionary steps before installation of the DVR.

1.

Keep all liquids away from the DVR.

2.

Install the DVR in a well-ventilated and dust-free area.

3.

Ensure environmental conditions meet factory specifications.

4.

Install a manufacturer recommended HDD.

DVR Installation

During the installation of the DVR:

1.

Use brackets for rack mounting.

2.

Ensure there is ample room for audio and video cables.

3.

When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter.

4.

Connect both the alarm and RS-485 cable.

5.

Allow at least 2cm (~0.75-inch) of space between racks mounted devices.

6.

Ensure the DVR is grounded.

7.

Environmental temperature should be within the range of -10 ºC ~ 55 ºC, 14ºF ~ 131ºF.

8.

Environmental humidity should be within the range of 10% ~ 90%.

Hard Disk Installation

Before you start:

Before installing a hard disk drive (HDD), please make sure the power is disconnected from the DVR. A factory recommended HDD should be used for this installation.

Tools Required: Screwdriver.

To install a HDD on your DVR:

1.

Remove the cover fr om the DVR by unfastening the screws on the back and side.

2.

Install the HDD in the HDD rack using the provided screws. Fasten the screws on the bottom to fix the HDD.

1

User Manual of VODVR 9000 Series DVR

3.

Connect the HDD to the motherboard of the DVR with the included data cable.

4.

Connect the power cable to the HDD.

5.

Re-install the cover of the DVR and fasten screws.

2

User Manual of VODVR 9000 Series DVR

Front Panel

The front panel of VODVR9100 /VODVR9100 is shown below:

No.

1

2

3

4

5

Name

POWER

STATUS

Tx/Rx

USB Interface

IR Receiver

Rear Panel

VODVR9104HVI/ :

Table 1 Description of Control Panel Buttons

Function Description

POWER indicator turns green when DVR is powered up.

STATUS indicator lights in red when HDD is reading/writing.

Tx/Rx indictor blinks green when network connection is functioning properly.

Connects USB mouse or USB flash memory devices.

Receiver for IR remote.

VODVR9116 :

Note: The rear panel of VODVR9108 provides 8 video input interfaces.

VODVR9116 :

Note: The rear panel of VODVR9108 provides 8 video input interfaces.

3

User Manual of VODVR 9000 Series DVR

6

7

8

9

No.

1

2

3

4

5

10

11

12

Item

VIDEO IN

VIDEO OUT

USB Interface

HDMI

VGA

AUDIO IN

AUDIO OUT

LAN Interface

RS-485 Interface

12V

POWER

GND

Table 2 Description of Rear Panel

Description

BNC connector for analog video input.

BNC connector for video output.

Connects USB mouse or USB flash memory devices.

HDMI video output.

DB15 connector for VGA output. Display local video output and menu.

RCA connector for audio input.

RCA connector for audio output.

Connector for LAN (Local Area Network).

Connector for RS-485 devices. Connect the D+ and D- terminals to T+ and T- of PTZ receiver respectively.

12VDC power supply.

Switch for turning on/off the device.

Ground(needs to be connected when DVR starts up)

Peripheral Connections

RS-485 Connections

To connect RS-485 devices (e.g., pan/tilt unit) to the DVR:

Press and hold the orange part of the pluggable block; insert signal cables into slots and release the orange part.

Ensure signal cables are in tight.

Note: Make sure the pan/tilt receiver unit is connected to the D+ and D- of the RS-485 terminal of DVR.

4

User Manual of VODVR 9000 Series DVR

Specifications

Table 3 Specifications for VODVR9100

Model

Video/Audio input

VODVR9104 VODVR9008 VODVR9016

Video compression H.264

Video input 4-ch 8-ch

Video input interface BNC (1.0 Vp-p, 75 Ω), PAL /NTSC self-adaptive

16-ch

Audio compression G.711u

Video/Audio output

Hard disk

Audio input 1-ch, RCA (2.0 Vp-p, 1 kΩ)

Two-way audio input 1-ch, RCA (2.0 Vp-p, 1 kΩ) (using the audio input)

HDMI/VGA output

CVBS output

1-ch, resolution:

1920 × 1080P / 60 Hz ,1600 × 1200 / 60 Hz,1280 × 1024 / 60 Hz,

1280 × 720 / 60 Hz, 1024 × 768 / 60 Hz

1-ch, BNC (1.0 Vp-p, 75 Ω), resolution: PAL: 704 × 576, NTSC: 704 × 480

Encoding resolution 4CIF / 2CIF / CIF / QCIF

Frame rate

Video bit rate

Audio output

Audio bit rate

Dual-stream

Stream type

Synchronous playback

SATA

Capacity

Mode1:

4CIF / 2CIF @ 12 fps or

CIF / QCIF @ 25 fps

(P) / 30 fps (N)

Mode2:

Channel 1: 4CIF /

2CIF / CIF / QCIF @

25 fps (P) / 30 fps (N),

Channel 2~4: CIF /

QCIF @ 25 fps (P) /

30 fps (N)

Mode1:

4CIF / 2CIF @ 8 fps or

CIF / QCIF @ 25 fps (P) / 30 fps (N)

Mode2:

Channel 1&

Channel 5: 4CIF /

2CIF / CIF / QCIF

@ 25 fps (P) / 30 fps (N),

Other Channels:

CIF / QCIF @ 25 fps (P) / 30 fps (N)

32 Kbps ~ 3072 Kbps, or user defined (Max. 3072 Kbps)

Mode1:

4CIF / 2CIF

@6fps or

CIF / QCIF @ 25 fps (P) / 30 fps

(N) Mode2:

Channel 1: 4CIF /

2CIF / CIF / QCIF

@ 25 fps (P) / 30 fps (N),

Channel 2~16:

CIF / QCIF @

25 fps (P) / 30 fps (N)

1-ch, RCA (Linear, 1 kΩ)

64 Kbps

Support;

Sub-stream: CIF @ 6 fps, QCIF @ 25 fps (P) /30 fps (N))

Video, Video & Audio

4-ch

1 SATA interface

Up to 4TB capacity

8-ch 16-ch

5

User Manual of VODVR 9000 Series DVR

External interface

Network interface 1, RJ45 10M / 100M Ethernet interface

1 RS-485 interface, half-duplex Serial interface

USB interface 2, USB 2.0

Power supply

Consumption

(without hard disk or

DVD-R/W)

12 VDC

≤ 10 W

Working temperature -10 ºC ~+55 ºC

Working humidity 10% ~ 90%

≤ 10 W ≤ 15 W

General

Chassis Standalone 1U chassis

Dimensions

(W × D × H)

315 × 230 × 45 mm

Weight (without hard

≤ 2 kg ≤ 4 kg ≤ 4 kg disk or DVD-R/W)

HDD Storage Calculation Chart

The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate.

384K

448K

512K

640K

768K

896K

1024K

1280K

Bit Rate

96K

128K

160K

192K

224K

256K

320K

1536K

1792K

2048K

168M

196M

225M

281M

337M

393M

450M

562M

Storage Used

42M

56M

70M

84M

98M

112M

140M

675M

787M

900M

Note: Please note that supplied values for storage space used is just for reference. Storage space used is estimated by formulas and may have some deviation from actual value.

6

User Manual of VODVR 9000 Series DVR

Menu Operation

Menu Structure

The menu structure of the DVR is shown as below:

Startup and Shutdown

Proper startup and shutdown procedures are crucial to expanding the life of the DVR.

Before you start:

Check that the voltage of the extra power supply is the same with the device’s requirement, and the ground connection is working properly.

Starting up the device:

Steps:

1.

Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an

Uninterruptible Power Supply (UPS) be used in conjunction with the device.

2.

Press the POWER button on the rear panel. The Power indicator LED should turn green indicating that the unit begins to start up.

Shutting down the device:

Steps:

1.

Enter the Shutdown menu.

Menu > Shutdown

7

User Manual of VODVR 9000 Series DVR

2.

Click the Shutdown button to enter the following dialog box:

3.

Click the Yes button. The following message box pops up:

4.

Turn off the power switch on the rear panel of DVR.

Using the Setup Wizard

The Setup Wizard can walk you through some important settings of the device. By default, the Setup Wizard starts once the device has loaded.

Operating the Setup Wizard:

1.

Select the system resolution from the drop-down menu. The default resolution is 1280×1024/60Hz.

Click Apply to save the resolution settings.

8

User Manual of VODVR 9000 Series DVR

2.

Check the checkbox to enable Setup Wizard when device starts. Click Next to continue the setup wizard.

You can also click Cancel to exit the Setup Wizard, or use the Setup Wizard next time by leaving the “Start wizard when DVR starts?” checkbox checked and exit.

3.

Click Next button on the Wizard window to enter the Login window.

1) Enter the admin password. By default, the password is 12345.

2) To change the admin password, check the New Admin Password checkbox. Enter the new password and confirm the password in the given fields.

4.

Click the Next button to enter the Date and Time settings window.

Set the time zone, date format, system date and system time.

9

User Manual of VODVR 9000 Series DVR

5.

Click Next button which takes you back to the Network Setup Wizard window.

Set the network parameters, including the NIC type, IPv4 address, IPv4 subnet mask, default gateway, etc.

You can enable the DHCP to automatically obtain an IP address and other network settings from that server.

6.

Click Next button to enter the HDD Management window.

To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD.

10

User Manual of VODVR 9000 Series DVR

7.

Click Next button to enter the Record Settings window.

1) Select the camera to configure.

2) Check the checkbox to enable Start Recording.

3) Select the recording mode to Normal or Motion Detection.

4) Click Copy to copy the record settings of the current camera to other camera (s) if needed.

11

User Manual of VODVR 9000 Series DVR

5) Click OK to return to the Record Settings window.

8.

Click OK to complete the startup Setup Wizard.

Live View

Some icons are provided on screen in Live View mode to indicate different camera status. These icons include:

Live View Icons

In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the record and alarm in the channel, so that you can find problems as soon as possible.

Alarm (video loss, tampering or motion detection).

Alarm & Record

PTZ Control

Follow the procedure to set the parameters for PTZ. The configuring of the PTZ parameters should be done before you set the PTZ camera.

Before you start, please check that the PTZ and the DVR are connected properly through RS-485 interface.

In the Live View mode, you can press the PTZ Control button on the IR remote control, or choose the PTZ

Control icon to enter the PTZ toolbar.

12

User Manual of VODVR 9000 Series DVR

Icon

Table 5

Description of the PTZ toolbar icons

Description Icon Description Icon Description

Direction button and the auto-cycle button

Zoom+, Focus+,

Iris+

Zoom-, Focus-,

Iris-

The speed of the PTZ movement

Light on/off Wiper on/off

3D-Zoom

Patrol

Image

Centralization

Pattern

Preset

Menu

Previous item Next item

Start pattern/patrol

Stop the patrol or pattern movement

Minimize windows

Record

You can use the right-click menu in live view mode to configure recording for all channels.

1.

In the live view mode, use the mouse to right-click on the window to access the following menu:

Exit

13

User Manual of VODVR 9000 Series DVR

2.

Click the Start Recording submenu and select the recording mode to Normal Record or Motion Detection

Record.

3.

In the pop-up message box, click Yes to finish the quick recording settings for all channels.

Note: The full-screen motion detection triggered recording is configured by default in this mode.

Playback

Play back the record files of a specific channel in the live view menu.

Instant playback by channel

Choose a channel under live view using the mouse and click the button in the shortcut operation menu.

Note: Only record files recorded during the past five minutes on this channel will be played back.

14

User Manual of VODVR 9000 Series DVR

All-day Playback by channel

1.

Enter the All-day Playback menu.

Mouse: right click a channel in live view mode and select All-day Playback from the menu.

Press PLAY button on the IR remote control to play back record files of the channel under single-screen live view.

Under multi-screen live view, record files of the top left channel (not masked) will be played back.

2.

Playback management.

The toolbar in the bottom part of Playback interface can be used to control playing process.

15

User Manual of VODVR 9000 Series DVR

The channel and time selection menu will display by moving the mouse to the right of the playback interface.

Tick the channel or channels if you want to switch playback to another channel or execute simultaneous playback of multiple channels.

Backup

Recorded files can be backed up to various devices, such as USB flash drives, USB HDDs or a DVD writer.

To export recorded files:

1.

Click Menu>Export to enter Video Export interface.

Choose the channel (s) you want to back up and click the Quick Export button.

16

User Manual of VODVR 9000 Series DVR

2.

Enter Export interface, choose backup device and click Export button to start exporting.

3.

Check backup result.

Choose the record file in Export interface and click the button to check it.

17

User Manual of VODVR 9000 Series DVR

18

0201021020831