I NSTRUCTI ON M ANUAL
Before commencing assembly , please read these instructions thoroughly .
6='2*$5
(GM048XM)
Specifications
Wing Span: 98.5 in / 2500 mm
Wing Area: 667 sq in / 43 sq dm
Flying Weight: 48 oz / 1360 g
Fuselage Length: 45 in / 1145 mm
Requires: 4-channel radio w/ 4 micro servos. Outrunner
Motor KM0283010 w/ Propeller Adaptor HW2340100
20A Brushless ESC, 3 cells 11.1V 15C 1800 mAh Li-Po
battery & charger.
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
* Specifications are subject to change without notice.*
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
www . thewingsmaker . com
GM048XMPO28181206
SZD-45 OGAR
INDEX
BEFORE YOU BEGIN
P.1
PARTS LIST
P.2
ASSEMBLY
P.3-P.9
SAFETY PRECAUTIONS
P.9
BEFORE YOU BEGIN
1 Read through the manual before you begin, so you will have an overall idea of what to do.
2 Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for
warranty replacement. The manufacturer will replace any defective parts, but will not extend
to the parts that are good before gluing to defective parts during assembly. Warranty will
not cover any parts modified by customer. For pre-assembled kits, please check proper
functions of all servos on the ground before flying. Servo gears could be damaged when
control surfaces are hit during transportation of models. The manufacturer will replace any
servos due to manufacturer`s defect, but will not cover plane crashes due to damaged
servos not detected before flying.
3 Symbols used throughout this instruction manual comprise of the following :-
3mm
Apply epoxy glue.
Apply instant glue
(C.A.glue, super glue.)
Apply thread locker
Must be purchased separately !
Assemble left and right
sides the same way.
Ensure smooth non-binding
movement while assembling.
Peel off shaded portion
covering film.
Cut off shaded portion.
Drill holes with the specified
diameter (here: 3mm).
Pierce the shaded portion
covering film.
Warning!
Pay close attention here!
GM048XMPO28181206
P.1
Do not overlook this symbol !
Parts List
1.MAIN WING -- 1 pair
MICRO AILERON SERVO MOUNT PL5310020 -- 1 pair
STRAPER PL4112106 -- 2 pcs
CLEVIS PL4112105 -- 2 pcs
FUEL TUBE d2xD4x4mm -- 4 pcs
HORN PL4113103 -- 2 pcs
PUSHROD Ø1.4x60mm w/ Threads (For Aileron) -- 2 pcs
SCREW PA1.7x8mm -- 8 pcs
FIBRE TAPE 17x435mm -- 2 pcs
PLYWOOD 36.5x36.5x2mm -- 2 pcs
5.MAIN LANDING GEAR -- 1 pc.
MAIN WHEEL Ø50mm PL3111500-- 1 pc.
PLASTIC COLLAR d4xD8x3mm -- 1 pc.
COLLAR Ø3.1mm w/ Set Screw -- 1 set
SCREW PA3x10mm -- 2 pcs
SOCKET HEAD SCREW M3x30mm -- 1 pc.
WASHER d3.2xD12mm -- 2 pcs
M3 NYLON INSERT LOCK NUT -- 1 pc.
6.MOTOR MOUNT PL5440000 -- 1 pc.
SOCKET HEAD SCREW M3x8mm -- 4 pcs
SOCKET HEAD SCREW M2.5x8mm -- 4 pcs
SCREW PM2x12mm -- 3 pcs
SCREW PA1.7x8mm -- 3 pcs
WASHER d3xD7mm -- 4 pcs
WASHER d2.5xD6mm -- 4 pcs
SPINNER Ø36mm SP28036WH0 -- 1 set
9x6 FOLDING PROPELLER(3 BLADE) PL6314051 -- 1 set
2.FUSELAGE -- 1 set
STABILIZER & ELEVATOR -- 1 set
FIBRE TAPE 17x525mm -- 1 pc.
SCREW PA1.7x8mm -- 4 pcs
MICRO AILERON SERVO MOUNT PL5310020(R) -- 1 pc.
STRAPER PL4112106 -- 1 pc.
CLEVIS PL4112105 -- 1 pc.
FUEL TUBE d2xD4x4mm -- 2 pcs
HORN PL4113103 -- 1 pc.
PUSHROD Ø1.4x33mm w/ Threads (For Elevator) -- 1 pc.
PLYWOOD 36.5x36.5x2mm -- 1 pc.
NYLON BOLT M3x25mm PL6510202 -- 2 pcs
NYLON WASHER d3.1XD11mm PL6610202 -- 2 pcs
TUBES -- 2 pcs
3.FIBRE TAPE 17x185mm -- 1 pc.
SCREW PA1.7x8mm -- 4 pcs
MICRO AILERON SERVO MOUNT PL5310020(L) -- 1 pc.
STRAPER PL4112106 -- 1 pc.
CLEVIS PL4112105 -- 1 pc.
FUEL TUBE d2xD4x4mm -- 2 pcs
HORN PL4113103 -- 1 pc.
PUSHROD Ø1.4x42mm w/ Threads (For Rudder) -- 1 pc.
PLYWOOD 36.5x36.5x2mm -- 1 pc.
7.WING TUBE Ø8x900mm -- 1 pc.
RUBBER BAND 2.5x4mm -- 2 pcs
HOOK -- 1 pc.
8.BATTERY MAT 2x50x150mm (For Radio Equipment & Battery) -- 2 pcs
BATTERY TIE 200mm -- 1 pc.
RECEIVER TIE 160mm -- 1 pc.
CABLE TIE 150mm(For Brushless ESC) -- 1 pc.
9.COCKPIT -- 1 pc.
CANOPY -- 1 pc.
PILOT PC101050A -- 1 set
10.DECALS: GM048 DEC -- 1 set
11.FIELD STAND -- 1 set
4.TAIL LANDING GEAR PL3410030 --1 set
SCREW PA2x8mm -- 2 pcs
GM048XMPO28181206
P.2
1
Aileron Servo
PA1.7x8mm
Screw
8
Plywood
36.5x36.5x2 mm
Aileron Servo Lead
Fibre Tape
17x435 mm
Bottom View
Bottom
Fibre Tape
02L
02R
03L
03R
04L
04R
Bottom View
Clevis
PA1.7x8mm
Straper
Pushrod
Ø1.4x60mm
Fuel Tube
d2xD4x4mm
Fuel Tube
d2xD4x4mm
Horn
TWM PL8210010
CLEVIS WRENCH
Please choose either (02L&02R) or (03L&03R) or (04L&04R) that suits your servo.
GM048XMPO28181206
P.3
2
Stabilizer & Elevator
PA1.7x8mm
Screw
4
M3x25 mm
Screw
2
d3.1xD11mm Washer
Plywood
36.5x36.5x2 mm
2
Fibre Tape
Fibre Tape
17x525 mm
Bottom
02L
02R
03L
03R
04L
04R
Bottom View
Bottom View
Clevis
PA1.7x8mm
Ø1.4x33mm
Pushrod
Straper
Fuel Tube
d2xD4x4mm
Fuel Tube
d2xD4x4mm
Horn
TWM PL8210010
CLEVIS WRENCH
Please choose either (02L&02R) or (03L&03R) or (04L&04R) that suits your servo.
M3x25mm
(Stabi l i zer)
A
Tubes
A'
B
B'
(Mai n Wi ng)
Washer
d3.1xD11mm
A=A'
B=B'
Temporary install the main wing,
adjust leveling of the stabilizer
to make it as parallel to the main
wing as possible
Elevator Servo Lead
Extension cords
Don`t over tighten screws,too much force will deform the foam.
GM048XMPO28181206
P.4
Completed
3
Rudder Servo
PA1.7x8mm
Screw
4
Plywood
36.5x36.5x2 mm
Rudder Servo Lead
Fibre Tape
17x185 mm
Fibre Tape
02L
02R
03L
03R
04L
04R
Clevis
PA1.7x8mm
Straper
Pushrod
Ø1.4x42mm
Fuel Tube
d2xD4x4mm
Fuel Tube
d2xD4x4mm
Horn
TWM PL8210010
CLEVIS WRENCH
Please choose either (02L&02R) or (03L&03R) or (04L&04R) that suits your servo.
4
Tail Landing Gear
PA2x8 mm
Screw
2
PA2x8mm
Wheel Ø23mm
Plastic
Collar
1.2mm
Bottom View
GM048XMPO28181206
P.5
5
Main Landing Gear
Wheel Ø50mm
d4xD8x3mm
Plastic Collar
M3x3mm Set Screw
3.1mm Collar
PA3x10mm Screw
d3.2xD12mm
Washer
d3.2xD12mm
Washer
2
M3x30mm Socket Head Screw
M3 Nylon Insert
Lock Nut
M3x30mm
1
M3
Nylon Insert Lock Nut
1
PA3x10mm
d4xD8x3mm Plastic Collar
d3.2xD12mm Washer
2
1
3.1mm Collar w/ Set Screw
1
Bottom View
6
Outrunner Motor / Spinner
M2.5x8mm Socket Head Screw
M3x8mm
4
Make sure rotating motor casing is not in contact
with wirings or anything.
1
Socket Head Screw
Outrunner Motor
4
PM2x12mm
Screw
PA1.7x8mm
Screw
M3x8mm
d3xD7mm
Washer
3
Motor Mount
PL5440000
3
d2.5xD6mm Washer
d3xD7mm
2
4
Motor Mount PL5440000
Washer
3
4
4
M2.5x8mm
d2.5xD6mm Washer
Optional Parts
Optional Parts
Outrunner Motor 28/ 30
KM0283010
Propeller Adaptor
(d3xD5) HW2340100
EZ Connector
Don't over-tighten the M2.5 screws, too much
stress on the screws could split the firewall.
5
9x6 Folding
Propeller (3 Blade)
PL6314051
6
PA1.7x8mm
PM2x12mm
Spinner Ø36mm
M5 Nut
Tighten the PM2 screws so the propeller
blades cannot swing freely, but don`t
over-tighten the screws,let the propeller
blades align themselves when spinning .
7
TWM HW3111400
PROPELLER ADAPTOR WRENCH
Completed
If you notice that the three propeller blades have not aligned themselves in one plane before flying, align them visually and
advance the throttle slowly to full throttle. The propeller blades will be self-aligned.
GM048XMPO28181206
P.6
7
Main Wing
Aileron Servo Lead
Wing Tube Ø8x900mm
Hook
Rubber Band
Completed
8
Radio Equipment
Install and arrange the equipment as shown in the picture.
Receiver Tie
Battery Mat
Iron
ESC Connector
Cable Tie
Brushless ESC
Battery
Battery Tie
Receiver
Motor
ESC
Solder
9
Solder
TWM
KP0011310
Canopy
Pilot
Completed
Double Sided Tape
GM048XMPO28181206
P.7
10
Decals
A
A’
A=A’
B
B’
C
C’
B=B’ C=C’
11
Field Stand / Launching Pad
The field stand can be used as a launching-pad if you are flying on paved
runways. Place the 6='2*$5 on the stand, point it into the wind, check
your controls and advance the throttle. When the 6='2*$5 gets enough
air speed, pull the elevator gently and the 6='2*$5 will fly off the field
stand and get airborne gracefully.
GM048XMPO28181206
P.8
12 Control Throws
Adjust the control throws as shown in
the diagram. These throws are good for
general flying. You can adjust according
to your personal preference.
Elevator
12mm
12mm
Rudder
30mm
30mm
Ailerons
15mm
15mm
13 C.G.
The ideal C.G. position is 65mm (2.56in.) behind the leading edge
measured at where the wing meets the fuselage. In order to obtain
the C.G. specified, add weight to the fuselage or move the battery
position. Check the C.G. before flying.
65mm
2.56in
C.G.
http://www.thewingsmaker.com/instructionManuals.php
Warning!
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyer
is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# szd-45 ogar is specially designed to be powered by KM0283010 Outrunner Motor.
# Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller. Extreme caution should be exercised when working with
electric powered models. Make sure the propeller is cleared of all objects, especially your
hands before connecting the battery to the model. Make sure you understand the
operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one,
as accidental movement of the throttle stick will spin the propeller and could cause injuries.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
GM048XMPO28181206
P.9
Pl8210010
Small• Clevis
Large• Clevis
Outrunner 28/ 32 Deluxe (25% higher power)
KM02832R1
-Kv(rpm/V): 1010
-Operating Power: 225W
-Operating Voltage: 6-15V
-Operating Current: 15A
-Peak Current: 20A(max.15 sec.)
-Internal Resistance: 102 m ohms
-Diameter: 28mm
-Length: 32mm
-Weight: 60g
-Shaft Diameter: 3mm
-Shaft Length: 15mm
-Mounting Screw:
M3(Front) and M2(Back)
-Distance of Mounting Holes:
16mm and 19mm(Front),
12mm(Back)
GM048XMPO28181206
www.thewingsmaker.com
THE WINGS MAKER
GM048XMPO28181206
">
