Meijer.com

AGES 3

0810

0811

0812

0813

0814

0815

0816

0817

0818

0819

(0810-0819)

CHEVROLET

OWNER'S MANUAL

Please read entire manual before starting assembly.

Keep this manual along with your purchase receipt for future reference.

Chevrolet, all related emblems and the distinctive vehicle model body and grille designs are General Motors Trademarks used under license to National Products

Limited.

CAUTION

Screws contain potentially hazardous sharp points or sharp edges. Adult assembly required.

WARNING

To reduce the risk of injury, adult supervision is required. Never use on road ways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water. Always wear shoes, and never allow more than two riders.

National Products Ltd.

Room 413-415, Houston Centre,

63 Mody Road, Tsim Sha Tsui East,

Kowloon, Hong Kong.

WWW.NPL2.COM

[email protected]

CONTAINS LEAD. MAY BE HARMFUL IF EATEN OR

CHEWED. MAY GENERATE DUST CONTAINING LEAD.

CHOKING HAZARD-Small parts.

Not for children under 3 yrs.

Contents, colors and decorations may vary from those shown.

nt rta po Im

IMPORTANT

You must charge your battery for 18 hours before you use your vehicle for the first time.

Remember to

...

Charge the battery immediately after each use.

Charge the battery at least once a month during storage, even if the vehicle has not been used.

he battery a if you fail to follow the

instructions. Please refer to the Battery Care Section in this manual for more information.

Meijer.com

2

LIMITED WARRANTY

(The warranty and toll free number only apply in the United States and Canada.) under normal circumstances, solely for the purpose for which it was intended and has been given proper care and maintenance. The warranty does not cover damage by customer, damage which results from normal wear and tear or from alterations made by the customer, or damage caused by use for an unintended purpose. Shipping and handling are not covered by this warranty.

Please keep the original purchase receipt for any warranty claims, and inspect the product upon purchase for any defects or missing parts.

We are here to help -

For parts order, please visit: www.funcreation.net

For Customer Service, please email us: [email protected]

Or call our toll free number: 1-877-743-3899

on ati rm fo nt In rta po Im

Meijer.com

Table of Contents

3

2

3

Warning

.......................................................................................................................

4

Battery Warning

..........................................................................................................

5

Battery Charging

.........................................................................................................

6

Battery Care and Disposal

.......................................................................................

7

Parts List

......................................................................................................................

8

Assembly

..............................................................................................................

9- 12

Radio Installation

............................................................................................

.........

.

13

Operating your Vehicle

.....................................................................................................

14

Trouble Shooting ....

15-17

Label Decoration

...........................................................................................................

1 8

Parts Diagram

...................................................................................................

19

Important Information

Your new vehicle requires adult assembly. Please set aside at least 60 minutes for assembly.

You must charge your battery for 18 hours before you use your vehicle for the first time.

We recommend that you start charging your battery before beginning assembly . Please see Battery charging beginning on page 6 for detailed instructions.

Read this manual carefully for important safety information and operating instructions before using your vehicle. Keep these instructions for future reference as they contain important information.

This vehicle is designed for use on: concrete, asphalt or other hard surfaces; on generally level terrain; by children ages 3 and up.

Instruct the children on operation and safe driving rules before they take their first drive:

- always sit in the seat.

- always wear shoes.

- maximum two (2) riders at a time.

- do not place hands, feet or any part of the body,

clothing or other articles near moving parts while

the vehicle is in operation.

- do not allow other children near the car when driving.

Use this vehicle ONLY outdoors. Most interior flooring can be damaged by riding this vehicle indoors.

NPL ® will not be responsible for damage to the floor if the vehicle is used indoors.

To prevent damaging the motors and gears, do not tow anything behind the vehicle or overload it. Do not exceed the maximum weight capac ity of 130 lbs. (59 kg).

If you have any questions about your vehicle, please call our toll-free service lines at 1-877-743-3899 from 9 AM to 5 PM ( PST ) Monday through Friday.

Trained customer service representatives are available to take your call.

The NPL ® service centers will repair or replace parts under warranty at no extra charge, and can perform non-warranty repairs for a minimal charge.

(The warranty and customer service contact in this manual only apply in the United States and Canada.

)

IMPORTANT INFORMATION:

YOUR NEW VEHICLE REQUIRES ADULT ASSEMBLY.

PLEASE SET ASIDE AT LEAST 60 MINUTES FOR

ASSEMBLY.

g in rn Wa

Meijer.com

Warning

To Prevent Serious Injuries

This product is intended for use by children ages

3 and up, and is not intended for children under 3 years of age due to lack of ability to operate safely.

Maximum weight 130 Ibs. ( 59 kg). Maximum 2 riders at a time.

Do not leave children unattended. Adult supervision required.

from the children until assembled.

Read manual for detailed safety information prior to use.

Inspect product at regular intervals for wear or loose hardware and tighten as required. Remove from service if any abnormal conditions such as cracks or breaks exist.

Check all coverings regularly to make sure they are in place.

Batteries can fall out and injure a child if the vehicle tips over. Always use the battery c over.

When the temperature falls below 0°F(-18°C), outdoor use of this product is not recommended.

In extreme cold, plastic materials might lose resilience and may become brittle and crack upon impact. Store in a warmer and protected place.

Do not operate the vehicle outdoors if it is raining. Keep it in a dry area when not in use.

Disconnect the battery power supply when the vehicle is not in use to prevent the children driving the car without adult supervision.

Always make sure the seat is securely attached.

Only use the charger specified by NPL ® .

The charger and battery are not toys and must be regularly examined for damage to the cord, plug, enclosure and other parts.

In the event of damage, the damage or worn part must not be used until replaced.

Never modify the electrical system. Use o f the wrong type battery or charger could cause a fire or explosion.

Battery compartment and area under seat are not storage areas. Storing other articles may create a fire hazard. Do not store any articles in or near motor compartment.

Safe Driving Rules

ADULT SUPERVISION REQUIRED.

MAKE SURE CHILDREN KNOW AND

FOLLOW THESE RULES FOR SAFE

DRIVING .

Restrict children to safe riding areas:

Away from swimming pools and other bodies of water to prevent drowning.

Level ground to prevent tipovers and unintended downhill motion.

Away from steps, hills, driveways, roads and alleys.

Teach and learn the safety first:

Although most children can master the physical driving skills to control the vehicles, they do not have the mature judgment skills. Never let a child drive at any time without adult supervision, and take the time to carefully evaluate child’s skill levels and abilities to operate the vehicle safely. Children can not always recognize the hazards even after instruction. So teach appropriate safety rules before allowing any child to operate vehicle, and remember that THERE IS NO

SAFE SUBSTITUTE FOR DIRECT ADULT

SUPERVISON.

Riding rules:

Always sit on the seat and wear shoes.

Maximum two riders at a time.

Do not operate in the street or near moving vehicles.

Do not operate near bodies of water, obstructions or drop-offs.

Do not operate on sand, dirt or gravel.

Do not operate in the dark. Unexpected obstacles could cause an accident.

Do not operate on inclines or steep slopes.

Do not operate near flammable vapors (e.g. gasoline, paint thinner, acetone, liquid wax, etc.) Using the vehicle near flammable liquids can or vapors could cause an explosion or fire.

Do not place anything near moving parts such as motors, gears or wheels. Rotating parts can snag hair, fingers, etc., which may cause serious injury.

4

g in arn W ry tte Ba

Meijer.com

Battery Warning

5

ELECTRICAL HAZARD

WARNING

if vehicle tips over. Always use battery cover.

PREVENT FIRE

- Never modify the electrical system.

Alterations could cause a fire resulting

in serious injury and could also ruin the

electrical system.

- Use of the wrong type battery or

charger could cause a fire or explosion

resulting in serious injury.

- Use of NPL ® components in products

other than NPL ® vehicles could cause

overheating,fire or explosion.

The battery must be handled by adults o nly. The battery is heavy and contains

sulfuric acid (electrolyte). Dropping the

battery could result in serious injury.

Never allow children to charge the battery.

only. A child could be injured by the

electricity involved in charging the battery.

Never lift or carry the battery by the wires o r connector. This can damage the battery

and possibly cause a fire resulting in

serious injury. Lift and carry the battery

by the case only.

Read the safety instructions on t he battery.

Examine the battery, charger and their c onnectors for excessive wear or damage

each time you charge the battery. If

damage or excessive wear is detected, do

not use the charger or the battery until you

have replaced the worn or damaged part.

CAUTION

Only use the battery specified by NPL ®

Only use the charger specified by NPL

Only use the charger in dry locations.

®

.

.

About Thermal Fuses

Your NPL ®

12 volt battery is equipped with a built-in thermal fuse. The thermal fuse is a self-resetting safety device which automatically trips and shuts down operation of the vehicle if the vehicle is overloaded or the driving conditions too severe. Once a fuse has tripped it will automatically reset itself after approximately 10 seconds and allow the vehicle to resume normal operations. To avoid repeated automatic shut downs, do not overload the vehicle by exceeding the 130 lbs.(59 kg) maximum weight capacity or by towing anything behind the vehicle.

Avoid severe driving conditions, such as driving up very steep slopes or running into fixed objects, which can cause the wheels to stop spinning while power is still being supplied to the motors.

If a thermal fuse in a battery continually trips under normal driving conditions, please contact NPL ®

Service

Center at 1-877-743-3899.

(The warranty and toll free number only apply in the United

States and Canada.)

Important Notes

Your new battery must be charged for at least 18 hours

before you use it in your vehicle for the first time.

You do not need to remove the battery from your

vehicle to recharge it.

The battery must be upright while charging.

The charger is not a toy.

Do not short circuit the battery.

We recommend that you start charging your battery

before beginning assembly of your new vehicle.

Before charging the battery, examine the battery case

for cracks and other damage which may cause sulfuric

acid (electrolyte) to leak during the charging process.

If damage is detected, do not charge the battery or use it in your vehicle. Battery acid is very corrosive and can cause severe damage to surfaces it contacts.

Do not charge the battery on a surface which could be

damaged by the acid contained inside the battery. Take

precautions to protect the surface on which you charge

your battery.

If your battery is old and will not accept a charge, do not

leave it in the vehicle. Always remove a dead battery

from the vehicle.

Non-rechargeable batteries are not to be recharged.

Rechargeable batteries are only to be charged under adult supervision.

Do not mix new and old batteries.

Only batteries of the same or equivalent type as recommended are to be used.

Batteries are to be inserted with the correct polarity.

Exhausted batteries are to be removed from the toy.

The supply terminals are not to be short-circuited.

Do not mix alkaline, standard (carbon-zinc),or rechargeable (nickel-cadmium) batteries.

Rechargeable batteries (AA type ) are to be removed from the toy before being charged.

g in arg Ch ry tte Ba

Battery Charging

CAUTION

Non-rechargeable batteries are not to be recharged.

Make sure the charger connector is matching with the battery connector.

Make sure the brand, voltage and frequency of the

12V charger are in accordance with the wall outlet.

Battery

Connector

Batteries are to be inserted with the correct polarity.

Charger

Connector

The supply terminals are not to be short circuited.

1

Plug the battery connector into the charger connector.

Plug the charger into a standard wall outlet.

® ®

Only use the NPL 12 volt charger to charge your NPL 12 volt battery.

Note: if power flow to the wall outlet is controlled by a switch , make sure the switch is "ON".

Before first-time use, charge the battery for at least 18 hours. Never charge the battery longer than 24 hours.

Recharge the battery for at least 12 hours after each use of your vehicle.

Do not charge the battery longer than 24 hours.

Do not charge or store battery upside down. Charging produces explosive gases. Charge away from flames, sparks and lit cigarettes. Charge in a well ventilated area.

The power indicator on the charger allows you to see that there is power from the wall outlet.

Once the battery is charged, disconnect the battery connector from the charger connector. Unplug the charger from the wall outlet. The battery is now ready to be installed in your vehicle. Please see the following

Battery Installation Section for detailed instructions on installing your vehicle:

2

Meijer.com

6

Open the hood.

4

Disconnect the battery and vehicle plugs .

Connect the charger and vehicle plugs .

After it is fully charged, the battery plug must be reconnected into the plug from the main body.

l sa po d Dis an re Ca ry tte Ba

Meijer.com

Battery Care and Disposal

7

Care

If a battery leak develops, avoid contact with the leaking acid and place the damaged battery in a

bag.

If acid comes in contact with skin or eyes, flush with cool water for at least 15 minutes and call a physician immediately.

If acid is internally ingested, give water, milk of magnesia or egg whites immediately. Never give emetics or induce vomiting. Call a physician immediately.

Charge a new battery for at least 18 hours before first use.

Never charge the battery longer than 24 hours.

Overcharging or undercharging the battery may shorten battery life and decrease vehicle running time.

After the first charge, recharge the battery for at least

12 hours after each use. Never charge the battery longer than 24 hours. Charge the battery after each use, regardless of how long the vehicle was used.

The battery must be upright while charging.

Do not allow the battery to run down completely before charging.

Charge the battery before storing the vehicle.

Charge the battery at least once per month, even if the vehicle has not been used.

Leaving the battery in a discharged condition will ruin it.

If the vehicle will be stored for more than two months, be sure to disconnect the motor harness from the battery.

Do not store the battery in temperatures above o 75 F o or below-10 F.

Only use the 12 Volt battery specified by NPL ® .

Prevent the battery from moving freely inside the battery compartment. Make sure all screws for battery cover tighten.

Examine the battery, charger and its connector for excessive wear or damage each time you charge the battery. If damage is detected, do not use the charger or the battery until you have replaced the worn or damaged part.

Remember to remove an exhausted battery from the vehicle.

Battery leakage and corrosion can damage the vehicle.

Disposal

Your NPL ® battery is a sealed lead-acid

battery. It must be recycled or disposed of it in an

environmentally sound manner.

Never dispose your battery in the regular, household

trash. The incineration, landfilling or mixing of sealed

lead-acid batteries with household trash is prohibited

by law in most areas.

To get a replacement battery, please visit your local

retailer or contact at 1- 877-743 - 3899.

Always remove exhausted batteries from your toy.

Dispose of dead batteries properly. Never burn or

bury them.

Do not dispose of a lead-acid battery in a fire. The battery may explode or leak.

Return exhausted batteries to a federal or state approved l ead-acid battery recycler, such as a NPL ®

authorized service center, or a local seller of

automotive batteries.

For the service center, please call at 1- 877-743 - 3899 .

Contact your local waste management officials for

other information regarding the environmentally sound

collection, recycling and disposal of lead-acid

batteries. If you live in the State of Florida or

Minnesota, it is prohibited by law for anyone to throw

away lead-acid batteries in the municipal waste

stream.

(The warranty and customer service contact in this manual only apply in the United States and Canada.

)

TO PROLONG BATTERY LIFE, YOU MUST RECHARGE THE

BATTERY AFTER EACH USE. YOU MUST ALSO CHARGE

YOUR BATTERY IF IT HAS NOT BEEN USED FOR 30 DAYS

OR MORE.

t Lis rts Pa

Meijer.com

Parts List

Please identify all parts before assembly and save all packaging material until assembly is completed to ensure that no parts are discarded.

Metal parts have been coated with lubricant for protection during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant.

8

Front Bumper x 1 Hood x 1

Vehicle x 1

Grill x 1 Mirrors x 2 Windshield x 1 Dashboard x 1

Bumper Support x 1 Seat x 1 Rear Deck x 1 Rear Bumper x 1

Screw x 10(ST4 x 20)

For wheels:

Screw x 31(ST4 x 14) Screw x 2(ST4 x 14)

For steering wheel:

Charger x1

Hubcap x 2 Bushing x 2

Nut x2

(M8 x T5)

Front Wheel x 2

Tools needed:

Wheel Cover x 2

Washer x 4

Nut x2

(M10 x T5)

Turning shaft x1 Steering Wheel x 1

Steering Wheel Cover x 1

Spare parts: Requires:

Screwdriver(Not included)

Lock nut tool(Included)

Bushing x1 Washer x2

Nut x1

(M10 x T5)

Nut x1

(M8 x T5) d.c.1.5V AA LR6

Screw x 2(ST4 x 20) Screw x 2(ST4 x 14) Screw x 2(ST4 x 14)

3 X 1.5V "AA" (LR6) batteries (Not included)

I ly mb se As

Meijer.com

Assembly

9

WARNING

Children can be harmed by small parts, sharp edges and sharp points in the vehicles unassembled state, or by electrical items. Care should be taken in unpacking and assembling the vehicle. Children should not handle parts, including the battery, or help in the assembly of the vehicle.

1 2

Screw x 4(ST4 x 14)

3

Fit the rear deck onto the vehicle.

Screw x 12(ST4 x 14)

Fit the rear bumper onto the vehicle.

Screw x 3(ST4 x 14)

Note: The seat is adjustable and has two positions. You can move the seat back as your child grows.

- Insert both tabs on the front edge of the seat

into on of the sets of slots inside the vehicle.

- Choose the slots closets to the dash for

shorter drivers and the slots furthest from the.

dash for taller drivers

Screw x4(ST4 x 14)

Fit the dashboard onto the windshield.

II ly mb se As

Meijer.com

Assembly

6

Screw x 4(ST4 x 20) Screw x 2(ST4 x 14)

Fit the dashboard and windshield assembly onto the posts near front end of the vehicle.

Screw x4(ST4 x 14)

- Fit a mirror onto the vehicle.

Hint: Each mirror do not seem to fit, try assem

bling on the other side.

- Insert two (ST4 x 14 ) screws into the mirror

with vehicle and tighten.

- Repeat the procedure for the other side.

7 8

10

Screw x 2(ST4 x 20)

Place the vehicle upside down.

- Slide the bumper support (Ribbed side up)

into the slot front end of the vehicle.

- Insert two (ST4 x 20 ) screws into the bumper

support and tighten.

Screw x 6(ST4 x 20)

Fit front bumper onto the vehicle. Insert 6 screws and tighten.

III ly mb se As

Meijer.com

Assembly

10

11

9

Screw x6(ST4 x 14)

- Place the vehicle upside down.

- Insert 4 screws into the front bumper with

bumper support and tighten.

Screw x2(ST4 x 14)

- Fit the grill onto the front bumper.

- Insert two screws into the grill and tighten.

11 12 washer x 4

Nut x2

(M10 x T5)

- Slide the washer onto axle

- Place bushing into inner recess on side of

wheel.

- Slide wheel, wheel cover and washer onto

axle.

- Use lock nut tool to tighten the nut.

- Snap the hubcap.

- Repeat the procedure for the other side

Nut x1

(M8 x T5)

- Insert the straight end of the steering column

down through the hole in the vehicle floor and

out through the hole in the dash.

- Insert the curved end of the steering column

through the bole in the steering linkage.

- Use lock nut tool to tighten the nut.

IV ly mb se As

Meijer.com

13

Assembly

14

15

Apply all decals before you install the steering wheel.

Nut x1

(M8 x T5)

- Position the steering wheel so that the large

opening is UP.

- Fit the steering wheel onto the steering column.

- Use lock nut tool to tighten the nut.

- Snap the steering wheel cup.

12

- Fit the long tabs on the hood into the slots in

the front end of the vehicle.

- Pull the hood forward and lower

Note: The hood is held down by magnets. Simply lift to open the hood. Do not use around items that are sensitive to or affected by magnetic fields.

n tio lla sta In dio Ra

13

1

Radio Installation

2

Meijer.com

Take out the radio.

3 X 1.5V "AA" (LR6) batteries (Not included) the compartment.

SOUND BUTTONS

POWER ON/OFF &

VOLUME CONTROL

TUNE -

MP3 LINE

IN JACK

TUNE +

INDICATOR LIGHT

Tip for MP3:

Turn on the power switch.

Plug in MP3 cable (not included).

Adjust volume when need.

Radio and sound features will be shut off when MP3 is plugged in.

le hic Ve ur g yo tin era Op

Meijer.com

Operating your Vehicle

Forward

Push the shifter in Forward position and press the accelerator slowly.

Reverse

Push the shifter in Reverse position and press the accelerator slowly.

High Speed

The high speed lock-out must first be removed.

Afterwards push the shifter to High speed position and press the accelerator slowly.

Important tip

Make sure the vehicle has come to a completely stop before switching between “ Forward ” and “ Reverse ”.

Beginner use - low speed

Vehicle has been pre-set to operate at low speed

(2.5 mph, (4 kmh) maximum). Once your child has mastered safe driving skills and understands the Safe Driving Rules, the high speed lock – out screw can be removed to allow the vehicle to operate at both high and low speeds.

Advanced use - disconnecting the high speed lock-out

Removing the high speed lock-out screw will allow the vehicle to be driven at the higher speed (5 mph,

(8 kmh) maximum) as well as the the lower speed

(2.5 mph, (4 kmh) maximum).

However, prior to removing the screw, be sure your child can safely steer and operate the vehicle and knows the rules for safe driving.

Cautious: High speed lock - out screw removing must be done by an adult!

Stop

Vehicle will automatically stop after the accelerator is released.

Safety devices

AUTO POWER OFF. If the motor is overloaded for any reason, including improper usage, an electrical circuit breaker will automatically cut off the power, then resume after the parts have cooled!

Maintenance

Clean with a dry, soft cloth only. Do not wash with water or corrosive agents.

Store vehicle in a dry area when not in use, since moisture could cause the metal components and electrical parts to corrode.

High speed Forward Reverse

Remove lock - out screw for high speed

Accelerator

Remember to charge the battery monthly while the vehicle is not in regular use.

Check and tighten all screws and coverings regularly.

Check all plastic parts for cracks. Replace as necessary.

14

g I tin oo Sh le ub Tro

Meijer.com

Trouble Shooting

15

IMPORTANT! If you experience a problem with your vehicle, first check the Problems and Solutions Guide below. If you still experience a problem, please contact NPL

®

Service Center , Toll-free at 1-877-743-3899 from 9 AM to 5 PM ( PST )

Monday through Friday. Or email us [email protected] or visit us www.funcreation.net for assistance and information from our trained technical staff. (The warranty and customer service contact in this manual only apply in the

United States and Canada.

)

Problem Possible Cause Solution

Car does not move Circuit breaker tripped Circuit breaker may “trip” and stop the vehicle if it is overloaded or the driving conditions too severe. The breaker will automatically reset after approximately 10 seconds, and the vehicle will operate normally. To avoid repeated automatic shut downs, do not overload the vehicle by exceeding the weight limit of 59kg, or by towing anything behind the vehicle. Do not drive uphill or run into fixed objects, which can cause the wheels to stop spinning while power is still being supplied to the motors. If breaker continually trips, contact your NPL ® Service Center.

Loose wire or connectors

Dead battery

Undercharged battery

Check all wires and connectors. Make sure that the motor harness connector is plugged in tightly to the battery, and that there are no loose wires around the motor.

An old or improperly cared battery may be dead. If you are unsure whether it is dead or not, you can have it tested at your NPL ®

Service Center.

A new battery should have been charged for at least 18 hours before using the vehicle for the first time. After that, it must be recharge the battery for at least 12 hours after each use .Never charge longer than

24 hours. Check all connectors; make sure the charger is plugged into the wall. Make sure the power flow to the outlet is on.

Charger is not working

Electricity switch damages

Car was running but suddenly stopped

Loose wire or connectors

Circuit breaker tripped

You must have a volt meter in order to tell whether the charger is working or not. If you think there maybe a problem with the charger ,

When exposed to water or moisture, electricity can become corroded, or can jam due to loose dirt, sand or gravel.

Check all wires and connectors. Make sure that the motor harness connector is plugged into the battery tightly, and that there are no loose wires around the motor.

Circuit breaker may “trip” and stop the vehicle if it is overloaded or the driving conditions too severe. The breaker will automatically reset after approximately 10 seconds, and the vehicle will operate normally. To avoid repeated automatic shutdowns, do not overload the vehicle by exceeding the weight limit of 59kg, or by towing anything behind the vehicle. Do not drive uphill or run into fixed objects, which can cause the wheels to stop spinning while power is still being supplied to the motors. If breaker continually trips, contact your NPL ® Service Center.

g II tin oo Sh le ub Tro

Meijer.com

Trouble Shooting

Problem

Short operating time (less than 1 hour per charge)

Vehicle is sluggish

Only one rear wheel spins

Possible Cause

Undercharged battery

Overcharge battery

Solution

A new battery should have been charged for at least 18 hours before using the vehicle for the first time. After that, it must be recharge the battery for at least 12 hours after each use .Never charge longer than 24 hours. Check all connectors; make sure the charger is plugged into the wall.

Make sure the power flow to the outlet is on.

Never charge battery longer than 24 hours. If you think the battery maybe damage due to overcharging, contact

NPL

®

Service Center for testing.

Old battery will not accept a full charge Even with proper care, a rechargeable battery does not last forever. Average battery life is 1 to 3 years depending on vehicle use and use conditions. Replace the battery with a new NPL

®

12 volt rechargeable battery. Do not substitute parts. To get a replacement battery, please contact NPL ® Service Center.

Undercharged battery A new battery should have been charged for at least 18 hours before using the vehicle for the first time. After that, it must be recharge the battery for at least 12 hours after each use .Never charge longer than 24 hours .Check all connectors; make sure the charger is plugged into the wall.

Make sure the power flow to the outlet is on.

Battery needs charging Be sure to charge the battery after each use.

16

Old battery will not accept a full charge Even with proper care, a rechargeable battery does not last forever. Average battery life is 1 to 3 years depending on vehicle use and use conditions. Replace the battery with a new NPL ® 12 volt rechargeable battery. Do not substitute parts. To get a replacement battery, please contact NPL ® Service Center.

Vehicle is overloaded

Driving conditions are too stressful

Allow no more than 2 riders at a time, follow the 130

Ibs. (59 kg) weight capacity and don't tow anything behind the vehicle.

Use only on a generally level ground.

Vehicle is operating in low speed It is possible that only one rear wheel may spin when both rear wheels are raised off the ground and the vehicle is in low speed. This does not necessarily indicate a problem.

Check for proper operation of the drive system by raising the rear wheels off the ground and pressing the foot pedal.

If only one rear wheel spins, carefully press your hand on the spinning wheel to slow it down. The other rear wheel should begin to spin. If the other rear wheel does not begin to spin, there may be a problem with the vehicle. Contact

NPL ® Service Center for diagnosis and repair.

g III tin oo Sh le ub Tro

Meijer.com

Trouble Shooting

17

Problem

Intermittent vehicle operation

When the go foot pedal is pressed, the vehicle won't run without a push

Possible Cause

Loose wire or connector

Motor or electrical switch damage

Loose wire or connector

“Dead Spot” on motor

Solution

Check all wires around the motors and all connectors to make sure they are tight.

Contact your NPL ® Service Center for diagnosis and repair at 1-877-743-3899.

Check all wires around the motors and all connectors to make sure they are tight.

Contact your NPL

®

Service Center for diagnosis and repair at 1-877-743-3899.

Contact your NPL

®

Service Center for diagnosis and repair at 1-877-743-3899.

No action required.

Motor gear box makes a loud grinding or clacking noise

Charger get warm during use

Broken gears

Battery makes gurgling or sizzling noise while charging

This is normal and should not be a concern.

Some noise and swelling is normal and should not be a concern

No action required. If the battery does not make noise while charging. It does not mean it isn't accepting the charging.

If, after reviewing the Problems and Solutions Guide, the vehicle still fails to operate, please contact your NPL

®

Service Center toll-free at 1-877-743-3899.

Note! For faster service when calling Consumer Relations, completely charge the battery before calling and have the following available by the phone:

Vehicle

Vehicle model number .

Vehicle production run number .

( The warranty and customer service contact in this manual only apply in the United States and Canada.

)

n tio ra co l De be La

Meijer.com

Label Decoration

Proper label application will help to keep the labels looking their best! When applying labels, keep the following guidelines in mind:

Wash your hands before applying the labels.

Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils.

Place the labels exactly as shown in the illustrations.

For best results, avoid repositioning a label once it has been applied to the vehicle.

After applying a label, rub the label firmly with a clean, dry cloth to make sure the label is adhered to your

vehicle. Start at the center of a label, and smooth towards the outer edges to remove air bubbles.

18

Front View

View Back

m gra Dia rts Pa

Meijer.com

Parts Diagram

5

6

4

7

8

19

2

3

9

10

1

22

21

20

19

18 17

14

16

15 13

12

11

Note: Some parts shown are assembled to both sides of the vehicle.

6

7

4

5

8

No.

Part

1 Vehicle

2

3

Rear Bumper

Rear Deck

Seat

Steering Wheel Cover

Steering Wheel

Turning Shaft

Dashboard

Quantity

1

1

1

1

1

1

1

1

No.

9

10

11

12

13

14

15

16

Part

Windshield

Hood

Grill

Front Bumper

Bumper Support

Battery

Washers

Bushings

Quantity

1

1

1

1

2

1

1

2

No.

Part

17 Front Wheels

18 Wheel Covers

19 Washers

20 Nuts

21

22

Hubcaps

Mirrors

Quantity

2

2

2

2

2

2

Meijer.com

National Products Limited

STOP!

DO NOT RETURN TO STORE

This product cannot be returned for a refund after it has been unpacked and used.

Call our toll- free 1-877-743-3899 or fax us 1-909-869-5945 or email us customers erv ice@funcre ation.net or visit us www.funcre ation.net for assistance and information from our trained technical staff .