IPC-622 Series User Manual 6U-High Multi-segment Rackmount Industrial Computer

IPC-622 Series User Manual 6U-High Multi-segment Rackmount Industrial Computer
IPC-622 Series
6U-High Multi-segment
Rackmount Industrial Computer
Chassis
User Manual
Copyright Notice
This documentation and the software included with this product are copyrighted, December 2005, by Advantech Co., Ltd. All rights are reserved.
Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of
Advantech Co., Ltd. Information provided in this manual is intended to
be accurate and reliable. However, Advantech Co., Ltd. assumes no
responsibility for its use, or for any infringements of the rights of third
parties which may result from its use.
Acknowledgements
Intel®, Pentium® 4, and Celeron® are trademarks of Intel Corporation.
The IPC-622, PCA-6120, PCA-6120P4, PCA-6120D, PCA-6120DP4,
PCA-6120Q, PCA-6120P12, PCA-6120P18, PCA-6119P7, PCA6119P16, PCA-6119P17, PCA-6118DP7, PCA-6116QP2, and PCA6115QP2X-A1 are trademarks of Advantech Co., Ltd.
All other product names or trademarks are the properties of their respective owners.
On-line Technical Support
For technical support and service, please visit our support website at:
http://www.advantech.com/support
Part No. 2002062201 2nd Edition
December, 2005
IPC-622 User Manual
ii
A Message to the Customer
Advantech customer services
Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech
equipment is destined for the laboratory or the factory floor, you can be
assured that your product will provide the reliability and ease of operation
for which the name Advantech has come to be known. Your satisfaction
is our primary concern. Here is a guide to Advantech's customer services.
To ensure you get the full benefit of our services, please follow the
instructions below carefully.
Technical support
We want you to get the maximum performance from your products. If
you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones
we can give over the phone.
Please consult this manual first. If you still cannot find the answer, gather
all the information or questions that apply to your problem, and with the
product close at hand, call your dealer. Our dealers are well trained and
ready to give you the support you need to get the most from your Advantech products. In fact, most problems reported are minor and are easily
solved over the phone.
In addition, free technical support is available from Advantech engineers
every business day. We are always ready to give advice on application
requirements or specific information on the installation and operation of
any of our products.
Product warranty
Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
If an Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
iii
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1.
Collect all the information about the problem encountered. (For
example, model no. of the product, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything
abnormal and list any on-screen messages you get when the problem occurs.
2.
Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.
3.
If your product is diagnosed as defective, obtain an RMA (return
material authorization) number from your dealer. This allows us to
process your return more quickly.
4.
Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for warranty service.
5.
Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.
Initial Inspection
Before you installing your backplane, please make sure that the following
materials have been shipped:
• IPC-622 Chassis
• User Manual
• Warranty Card
• Accessory box with a pack of screws (for fixing disk drives, backplane
and ear handles), a pair of keys, two ear handles, three spare filters and
two 4-pin power wires inside.
If any of these items are missing or damaged, contact your distributor or
sales representative immediately. We have carefully inspected the IPC622 mechanically and electrically before shipment. It should be free of
marks and scratches and in perfect working order upon receipt. As you
unpack the IPC-622, check it for signs of shipping damage. (For example,
damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the
specifications, notify our service department or your local sales representative immediately. Also notify the carrier. Retain the shipping carton and
packing material for inspection by the carrier. After inspection, we will
make arrangements to repair or replace the unit.
IPC-622 User Manual
iv
Contents
Chapter
1 Introduction ..................................................... 2
1.1
1.2
1.3
1.4
1.5
1.6
Chapter
2
3
4
4
5
6
2 System Setup.................................................... 8
2.1
2.2
2.3
2.4
2.5
Chapter
Introduction .............................................................
Specifications ..........................................................
Power Supply Options.............................................
Environment Specifications ....................................
Dimensions..............................................................
Safety Precautions...................................................
Removing the top cover .......................................... 8
Installing the Backplane .......................................... 9
Installing CPU card and add-on cards................... 10
Rubber pad ............................................................ 11
Installing Disk Drives ........................................... 11
3 Operation ....................................................... 14
3.1
The Front Panel of IPC-622 .................................. 14
3.1.1 Switch and Buttons .............................................. 14
3.1.2 LED indicators for System Status ....................... 14
3.1.3 LED indicators for Power Status ......................... 15
3.2
3.3
Replacing the Cooling Fan.................................... 16
Replacing the Filter ............................................... 17
3.3.1 Replacing the filter behind the front upper cover 17
3.3.2 Replacing the filter behind the front door ........... 18
3.4
Replacing the power supply ................................. 19
3.4.1 The redundant power supply model .................... 19
3.4.2 The PS/2 power supply model ............................. 20
Chapter
4 Alarm Board .................................................. 24
4.1
4.2
4.3
4.4
Alarm Board Layout .............................................
Alarm Board Specifications .................................
Switch Settings......................................................
Thermal Sensor .....................................................
v
24
25
26
27
Table of Contents
Appendix A Exploded Diagram ........................................ 30
Appendix B Backplane Options ........................................ 34
Appendix C Safety Instructions ........................................ 36
C.1 English................................................................... 36
C.2 German/Wichtige/Sicherheishinweise .................. 37
IPC-622 User Manual
vi
1
CHAPTER
2
General Information
Chapter 1 Introduction
1.1 Introduction
The IPC-622 is a 6U-high rackmount industrial computer chassis
designed for multi-system applications. It supports a backplane with up to
20 slots for quad-segment industrial system. It is configured with a 400 W
or 500 W PS/2 power supply or 460 W redundant power supply.
Unique alarm detection and notification to reduce system down time
The IPC-622 comes with a unique alarm module. This module automatically detects the system operating conditions, such as power, HDD, fan,
and system temperature. The front LED indicators show the system and
power status clearly. In the event of system failure, the alarm module will
make an audible beep to warn users to take essential actions.
Flexible storage options
IPC-622 provides abundant data storage solutions, such as two drive
housings that hold four front-accessible 5.25" disk drives (CD-ROM
drive, DVD-ROM drive or removable disk drive), and two internal 3.5"
HDD. The IPC-622 chassis allows integration with a wide range computing peripherals.
Outstanding mechanical designs
The IPC-622 is designed for multi-system use. With abundant power supply options and four high speed cooling fans support, it provides reliable
operation and good airflow design. The shockproof drive bay and the rubber pad with rubber cushions protect the system against harsh industrial
environments and unexpected shock. The front door with user-friendly
rotary lock prevents unauthorized access to the data storage. The redundant power supply module is hot-swappable and rear accessible. All these
easily-maintained modules reduce the system's Mean Time to Repair
(MTTR) and make IPC-622 the best solution for price, performance and
total cost of ownership.
IPC-622 User Manual
2
1.2 Specifications
• Construction: Heavy-duty steel
• Disk drive capacity: Support four front accessible 5.25" disk drives
and two internal 3.5" disk drives
• LED Indicators on front panel: Bi-color LEDs (green/red) for Power,
Fan and Temperature status; single-color LEDs (green) for HDD activity and Power Singles Status (+5 V, -5 V, +12 V, -12 V and +3.3 V)
• Switch and buttons on front panel: Power switch, Alarm Reset button
and up to four System Reset buttons behind the lockable front door
• Cooling fan: Four 9 cm x 9 cm x 25 mm, 53 CFM, hot-swappable cooling fans
• Air Filters: Two filters (142 mm x 97 mm) behind the front door. One
filter (380 mm x 92 mm) behind the upper front cover.
• Slide rails: General Device C-300 series supported
• Chassis color: Beige (Pantone 414U)
• Gross weight: 30 kg (66 lbs)
• Dimensions (W x H x D): 482 x 266 x 463 mm (19" x 10.5" x 18")
• Compliance: CE compliant, UL/cUL approved
3
Chapter 1
1.3 Power Supply Options
Table 1.1: Power Supply Options
Model Name
1757000193
1757000162
1757000177
Watt
400 W max.
(with PFC)
100 ~ 240 VAC
(Full range)
+5 V @ 35 A,
+3.3 V @ 25 A,
+12 V @ 30 A,
-5 V @ 0.8 A,
-12 V @ 1 A,
+5 VSB @ 2 A
500 W max.
(with PFC)
100 ~ 240 VAC
(Full range)
+5 V @ 40 A,
+3.3 V @ 30 A,
+12 V @ 32 A,
-5 V @ 0.8 A,
-12 V @ 1 A,
+5 VSB @ 2 A
460 W max.
(1+1 redundant)
100 ~ 240 VAC
(Full range)
+5 V @ 40 A,
+3.3 V @ 30 A,
+12 V @ 32 A,
-5 V @ 0.8 A,
-12 V @ 1 A,
+5 VSB @ 2 A
Minimum
load
+5 V @ 3 A,
+12 V @ 1 A,
+5 VSB @ 0.1 A
+5 V @ 2.5 A,
+12 V @ 1 A,
+5 VSB @ 0.1 A
+5 V @ 5 A,
+3.3 V @ 1 A,
+12 V @ 2.5 A,
+5 VSB @ 0.1 A
MTBF
91,000 hours @
25°C
UL/TUV/CB/
CCC
98,000 hours @
25°C
UL/TUV/CB/
CCC
98,000 hours @
25°C
UL/TUV/CB/
CCC
Input rating
Output
voltage
Safety
1.4 Environment Specifications
Table 1.2: Environment Specifications
Environment
Operating
Temperature
0 to 40°C
-20 to 60°C
(32 to 104°F)
(-4 to 140°F)
10 to 85% @ 40°C,
10 to 95% @ 40°C,
non-condensing
non-condensing
1 Grms
2G
10 G with 11 ms dura30 G
tion, half sine wave
0 to 3,048 m (0 ~ 10,000 ft)CE compliant, UL/cUL approved-
Humidity
Vibration
Shock
Altitude
Safety
IPC-622 User Manual
Non-operating
4
1.5 Dimensions
Figure 1.1: Dimensions of IPC-622
5
Chapter 1
1.6 Safety Precautions
Warning!
Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the
power is on. Sensitive electronic components can be damaged by sudden
power surges. Only experienced electronics personnel should open the
PC chassis.
Caution!
Always ground yourself to remove any static charge before touching the
motherboard, backplane, or add-on cards. Modern electronic devices are
very sensitive to static electric charges. As a safety precaution, use a
grounding wrist strap at all times. Place all electronic components on a
static-dissipative surface or in a static-shielded bag when they are not in
the chassis.
FCC
This device complies with the requirements in part 15 of the FCC rules:
Operation is subject to the following two conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired operation
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
device in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his/her
own expense. The user is advised that any equipment changes or modifications not expressly approved by the party responsible for compliance
would void the compliance to FCC regulations and therefore, the user's
authority to operate the equipment.
IPC-622 User Manual
6
CHAPTER
2
2
System Setup
Chapter 2 System Setup
The following procedures instruct users to install the backplane, add-on
cards, disk drives into the IPC-622 chassis. Please refer to Appendix A,
Exploded Diagram, for all the detailed parts names of IPC-622.
Note: Use caution when installing or operating the components with the
chassis open. Be sure to turn off the power, unplug the power cord and
ground yourself by touching the metal chassis before you handle any
components inside the machine.
2.1 Removing the top cover
To remove the top cover, please refer to Figure 2.1 and proceed as below.
1.
Detach the eight screws along with the top cover and three screws
on top front of the top cover.
2.
Remove the top cover.
Figure 2.1: Removing the top cover
IPC-622 User Manual
8
2.2 Installing the Backplane
IPC-622 supports backplanes of up to 20 slots. To install the backplane,
please refer to Figure 2.2 and proceed as follows:
1.
Remove the top cover.
2.
Attach the EMI shield on the backplane. Put the backplane in the
proper location and then fasten it onto the chassis.
3.
Connect the 12-pin AT power connector, 6-pin +3.3V and 6-pin
+5V power connector from the power supply to the backplane.
Figure 2.2: Installing the backplane
9
Chapter 2
2.3 Installing CPU card and add-on cards
IPC-622 supports up to 20 add-on cards. To install a CPU card or add-on
cards, please proceed as follows:
1.
Remove the top cover.
2.
Select a vacant PICMG slot for the full-length CPU card or PCI/
ISA slot for other add-on cards and remove the corresponding I/O
bracket attached to the rear plate of the chassis.
3.
Insert the CPU card or add-on card vertically into the proper slot
(See Figure 2.3). For CPU cards or full-length cards, please make
sure that the card bracket has been inserted properly and the other
edge of the card has been inserted into the plastic guiding fillister.
Fasten the card by a screw on top of the I/O bracket.
4.
Repeat Step 2 and 3 if there is more than one add-on card.
5.
Plug the ATX feature wire from the power supply into the CPU
card.
6.
Plug the relevant wires on the chassis to the CPU card such as
power switch wire, system reset switch wire, power LED wire, and
HDD LED wire.
Figure 2.3: Installing a CPU card or a full-length card
IPC-622 User Manual
10
2.4 Rubber pad
The rubber pad underneath the top cover is designed for protecting CPU
cards from vibration and shock. (See Figure 2.4).
Figure 2.4: Top cover with the rubber pad
2.5 Installing Disk Drives
The disk drive bay in the front section can hold four 5.25" disk drives
(such as CD-ROM drive, CD-R/W drive, DVD-ROM drive, or removable
disk drives, etc.). To install the disk drive, please proceed as follows:
1.
Remove the top cover.
2.
Unscrew the four screws on the front of the disk drive shield. Hold
the two thumb screws to take out the disk drive housing. (Figure
2.5)
3.
Insert the disk drive in place in the disk drive housing, and then fix
it with the screws provided. (Figure 2.6)
4.
Connect a 40-pin flat cable to a CD-ROM drive (or CD-RW drive
or DVD-ROM drive or IDE HDD), or a SCSI cable to a SCSI
HDD, or a SATA cable to a SATA HDD. Then plug the 4-pin power
connector into each disk drive.
11
Chapter 2
5.
Put back the disk drive housing to the correct location and fasten it
with the four screws.
Figure 2.5: Taking out the disk drive housing
Figure 2.6: Installing the disk drives
IPC-622 User Manual
12
CHAPTER
3
2
Operation
Chapter 3 Operation
3.1 The Front Panel of IPC-622
On the front panel, there is one Power On/Off switch, one Alarm Reset
button, four System Reset buttons, and four USB ports. There are 9 LED
indicators on the lockable front door. Their individual functions are
described as below.
3.1.1 Switch and Buttons
Power On/Off switch: Press this button to turn the system power on or
off.
System Reset button: Press the button to reboot the individual system
(up to four systems).
Alarm Reset button: Whenever a fault occurs in the system (e.g., fan
failure or the temperature in the chassis is too high), the audible alarm
will be activated. Pressing this button will stop the alarm from beeping.
3.1.2 LED indicators for System Status
The LED panel on the front door shows a series of indicators which are
grouped into two categories for System Status and Power Status.
Figure 3.1: LED indicators
The following table describes the LED indicators for System Status.
Table 3.1: LED indicators for System Status
LED
Description
Green
Red
PWR
HDD
TEMP
FAN
System power
Hard disk drive activity
Temperature in the chassis
Cooling fan status
Normal
Data access
Normal
Normal
Abnormal
No light
Abnormal
Abnormal
IPC-622 User Manual
14
When the system powers is on, the PWR LED is always Green.
When the PWR LED is RED, it indicates a redundant power supply module
failure. To stop the alarm beep, press the Alarm Reset button. Examine the
redundant power supply module right away and replace the failed module
with a good one.
If the TEMP LED is RED, it means that inside of the chassis is overheated.
An audible alarm will be activated. To stop the alarm beep, press the Alarm
Reset button. Inspect the fan filter and the rear section of the chassis immediately. Make sure the airflow inside the chassis is smooth and not blocked
by dust or other particles.
When the FAN LED is RED, it indicates a failed cooling fan, and the alarm
is also activated. To stop the alarm beep, press the Alarm Reset button and
then replace the failed fan with a good one immediately.
3.1.3 LED indicators for Power Status
The following table is the individual LED which indicates the status of
the backplane voltage signals.
Table 3.2: LED indicators for Power Status
LED
Description
LED on
LED off
+5V
+12V
-5V
-12V
+3.3V
+5V signal
+12V signal
-5V signal
-12V signal
+3.3V signal
Normal
Normal
Normal
Normal
Normal
Abnormal
Abnormal
Abnormal
Abnormal
Abnormal
When an LED fails to light up, it means there is a problem with one of the
voltage signals. Please check if the power supply connector is properly
attached to the backplane. If the problem persists, consult with an experienced technician.
15
Chapter 3
3.2 Replacing the Cooling Fan
There are four cooling fans located in the front top of the chassis. They
provide the system with ample cooling by blowing air rearwards. To
replace the cooling fan, please refer to Figure 3.2 and proceed as below.
1.
Remove the front top chassis cover.
2.
Loose the thumb screw on top of the fan unit and then smoothly
pull it out. It will disconnect the cooling fan power connector.
3.
Replace the cooling fan with a new one.
4.
Fix the new cooling fan by fastening the thumb screw.
5.
Replace the front top chassis cover and fasten it.
Figure 3.2: Replacing the cooling fan
IPC-622 User Manual
16
3.3 Replacing the Filter
The filter is to block the dust or the particles from the work environment
and extend the system longevity. It's better to replace the new filter periodically. There is one filter behind the front upper cover and two filters on
lower left and lower right sides of the front door. To replace the filter,
please refer to Figure 3.3 and Figure 3.4 and proceed as follows.
3.3.1 Replacing the filter behind the front upper cover
1.
Loosen the four thumb screws located on the front upper cover and
then gently pull it forward. Please see Figure 3.3.
2.
Remove the filter and replace it with a new one.
3.
Return the front upper cover and then fasten it.
Figure 3.3: Replacing the filter
17
Chapter 3
3.3.2 Replacing the filter behind the front door
1.
Open the front door by rotating the lock.
2.
Loosen the screw located on the filter cover and then pull it aside.
Please see Figure 3.4.
3.
Remove the filter and replace it with a new one.
4.
Return the filter cover and then fasten it.
Figure 3.4: Replacing the filter
IPC-622 User Manual
18
3.4 Replacing the power supply
IPC-622 supports either PS/2 power supply or redundant power supply.
For replacing the power supply, please see details below.
3.4.1 The redundant power supply model
The redundant power supply is rear-accessible and hot-swappable. To
change the module, please proceed as below.
1.
Press the alarm reset button on the front panel to stop the alarm.
2.
Unplug the power cord on the failed power supply module.
3.
Loosen the screws on the module and then grab the handle to gently
pull it out (see Figure 3.5).
4.
Make sure that the new power supply module is the same rating as
the currently installed one.
5.
Slide the power supply module inward until it locks into the right
position.
6.
Fasten the screws and then plug the power cord.
Figure 3.5: Replacing the redundant power supply module
Note: When you plug the two power cords into the socket, please make
them the same direction (See Figure 3.6).
19
Chapter 3
Figure 3.6: Power cord plugs orientation on the socket
3.4.2 The PS/2 power supply model
With PS/2 power supply model, please proceed as below to replace the
power supply.
1.
Unplug the power cord from the power supply.
2.
Remove the top cover.
3.
Unplug the 12-pin AT power connector, 6-pin +3.3V and 6-pin
+5V power connectors from the backplane. And unplug other
power connectors from the disk drives.
4.
Loose the 8 screws on the top and both sides of the rear lower plate.
5.
Remove the four screws which mount the power supply to the rear
plate, then remove the rear lower plate and take out the power supply. Please see Figure 3.7.
6.
Place a new power supply and fix it onto the rear plate.
7.
Return the rear lower plate and then fasten it.
8.
Plug the 12-pin AT power connector, 6-pin +3.3V and 6-pin +5V
power connectors to the backplane. And plug other power connectors to the essential disk drives.
9.
Return the top cover and fasten it.
10.
Plug in the power cord.
IPC-622 User Manual
20
Figure 3.7: Replacing the single power supply
21
Chapter 3
IPC-622 User Manual
22
CHAPTER
4
2
Alarm Board
Chapter 4 Alarm Board
The alarm board is located behind the cooling fan near the middle section.
The alarm board makes an audible alarm when:
• Any power supply module of the redundant power supply fails
• One of the cooling fans fails
• Internal temperature of the chassis is too high
To stop the alarm beep, simply press the Alarm Reset button on the front
panel.
4.1 Alarm Board Layout
The layout and detailed specification of the alarm board are given below.
Figure 4.1: Alarm board layout
IPC-622 User Manual
24
4.2 Alarm Board Specifications
Input Power: +5V, +12V
Input Signals:
• 7 FAN connectors
• One thermal board connector (can connect up to 8 thermal boards in
series way)
• One power good input
• One alarm reset input
• One voltage signal connector (connect from backplane, includes 12V,
5V, +3.3V)
• One Hard Disk LED connector (connect from CPU card)
Output Signals:
• One LED board connector
• One LCM board connector
• One Buzzer output
Pin Definition
CN1: Auxiliary external power connector, standard mini 4-Pin
power connector
Pin 1
Pin 2
+12V
GND
Pin 3
Pin 4
GND
+5V
CN4: Thermal sensor (LM75) connector
Pin 1
Pin 2
+5V
T_SCLK
Pin 3
Pin 4
T_SDAT
GND
CN13: Voltage detect input connector
Pin 1
+5VSB
Pin 5
+5V
Pin 2
Pin 3
Pin 4
GND
GND
-5V
Pin 6
Pin 7
Pin 8
+3.3V
-12V
+12V
Pin 2
GND
CN16: Power good input
Pin 1
Power Good A
25
Chapter 4
CN17: Alarm reset connector
Pin 1
ALARM RESET
Pin 2
GND
Pin 9
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Temperature Good LED
Temperature Fail LED
FAN Good LED
FAN Fail LED
N/A
Power Good +3.3V
Power Good +5VSB
CN18: LED board connector
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
GND
Power Good +5V
Power Good +12V
Power Good -5V
Power Good -12V
HDD_1
Power Good LED
Pin 8
Power Fail LED
CN26: External HDD LED connector
Pin 1
HLED_ACT
Pin 2
N/A
Pin 2
+5V
Pin 5
Pin 6
Pin 7
Pin 8
GND
FAN_SEL3
GND
RESET
J1: External buzzer connector
Pin 1
Buzzer
SW1: Fan number select switch
Pin 1
Pin 2
Pin 3
Pin 4
GND
FAN_SEL1
GND
FAN_SEL2
4.3 Switch Settings
Fan Number Setting
Fan Number
SW 1-1
SW 1- 2
SW 1- 3
SW 1- 4
1
2
3
4
5
6
7
OFF
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
IPC-622 User Manual
26
4.4 Thermal Sensor
There is one thermal sensor located near the upper rear of the chassis
right plate. Please refer to Figure 4.2.
Thermal Sensor
Figure 4.2: Thermal sensor location
When inside temperature of the chassis is overheated, the thermal sensor
sends a signal to the alarm board and a continuous alarm will sound. To
stop the alarm beep, press the Alarm Reset button on the front panel.
Please refer to Figure 4.3 for the thermal sensor module layout. And users
can refer to the following temperature setting by adjusting the switch.
Figure 4.3: Thermal sensor module
27
Chapter 4
CN1: Temperature Sensor Connector
Pin 1
Pin 2
+5V
T_SCLK
Pin 3
Pin 4
T_SDAT
GND
CN2: Temperature Sensor Connector
Pin 1
Pin 2
+5V
T_SCLK
Pin 3
Pin 4
T_SDAT
GND
Sensor Number
SW 1 -1
SW 1 - 2
SW 1 - 3
SW 1 - 4
1
2
3
4
5
6
7
8
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
IPC-622 User Manual
28
A
APPENDIX
2
Exploded Diagram
Appendix A Exploded Diagram
Figure A.1: Exploded Diagram (1)
IPC-622 User Manual
30
Figure A.2: Exploded Diagram (2)
31
Appendix A
IPC-622 User Manual
32
B
APPENDIX
2
Backplane Options
Appendix B Backplane Options
IPC-622 supports a variety of backplanes, from 18-slot to 20-slot. Users
can contact an Advantech local sales representative for detailed backplane specification and relevant information.
Table B.1: Backplane models
Model Name
Segment
Slots Per Segment
PICMG
PICMG/PCI
PCI
ISA
PCA-6120-0B1
PCA-6120P4-0B1
PCA-6120P12-0A1
PCA-6120P18-0A1
PCA-6119P7-0B1
PCA-6119P16X
PCA-6119P17-0B1
PCA-6120D-0B1
PCA-6120DP4-0B1
PCA-6120DP7-0B1
PCA-6120Q-0B1
PCA-6116QP2-0B1
PCA-6115QP2X-A1
Single
Single
Single
Single
Single
Single
Single
Dual
Dual
Dual
Quad
Quad
Quad
-2
1
1
2
2
1
-4
3
-7
7
--1
1
--1
-2
-----
-4
11
17
7
16
16
-6
14
-8
8
20
14
7
1
10
1
-20
7
1
20
1
--
IPC-622 User Manual
34
C
APPENDIX
2
Safety Instructions
Appendix C Safety Instructions
C.1 English
1.
Read these safety instructions carefully.
2.
Keep this installation reference guide for later reference.
3.
Disconnect this equipment from any AC outlet before cleaning. Do
not use liquid or spray detergents for cleaning. Use a damp cloth.
4.
For pluggable equipment, the power outlet must be installed near
the equipment and must be easily accessible.
5.
Keep this equipment away from humidity.
6.
Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause damage.
7.
The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8.
Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.
9.
Position the power cord so that people cannot step on it. Do not
place anything over the power cord.
10.
All cautions and warnings on the equipment should be noted.
11.
If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient over-voltage.
12.
Never pour any liquid into an opening. This could cause fire or
electrical shock.
13.
Never open the equipment. For safety reasons, the equipment
should be opened only by qualified service personnel.
14.
If any of the following situations arises, get the equipment checked
by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work
according to the installation reference guide.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
IPC-622 User Manual
36
15.
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY
DAMAGE THE EQUIPMENT.
The sound pressure level at the operator's position according to IEC 7041:1982 is equal to or less than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1.
Advantech disclaims all responsibility for the accuracy of any statements
contained herein.
C.2 German/Wichtige/Sicherheishinweise
1.
Bitte lesen sie Sich diese Hinweise sorgfältig durch.
2.
Heben Sie diese Anleitung für den späteren Gebrauch auf.
3.
Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen.
Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten
dient ein angefeuchtetes Tuch zur Reinigung.
4.
Die Netzanschlußsteckdose soll nahe dem Gerät angebracht und
leicht zugänglich sein.
5.
Das Gerät ist vor Feuchtigkeit zu schützen.
6.
Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten.
Ein Kippen oder Fallen könnte Verletzungen hervorrufen.
7.
Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät
vor überhitzung schützt. Sorgen Sie dafür, daß diese Öffnungen
nicht abgedeckt werden.
8.
Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.
9.
Verlegen Sie die Netzanschlußleitung so, daß niemand darüber
fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden.
10.
Alle Hinweise und Warnungen die sich am Geräten befinden sind
zu beachten.
11.
Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten
Sie es vom Stromnetz trennen. Somit wird im Falle einer
Überspannung eine Beschädigung vermieden.
12.
Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder
Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw
elektrischen Schlag auslösen.
37
Appendix C
13.
Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der
elektrischen Sicherheit nur von authorisiertem Servicepersonal
geöffnet werden.
14.
Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz
zu trennen und von einer qualifizierten Servicestelle zu überprüfen:
a. Netzkabel oder Netzstecker sind beschädigt.
b. Flüssigkeit ist in das Gerät eingedrungen.
c. Das Gerät war Feuchtigkeit ausgesetzt.
d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend
funktioniert oder Sie mit Hilfe dieser Anleitung keine
Verbesserung erzielen.
e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
15.
Bitte lassen Sie das Gerät nicht unbehehrt hinten unter -20° C (-4°
F) oder oben 60° C (140° F), weil diesen Temperaturen das Gerät
zerstören könten.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000
beträgt 70dB(A) oder weiger.
DISCLAIMER: This set of instructions is provided according to IEC7041. Advantech disclaims all responsibility for the accuracy of any
statements contained herein.
IPC-622 User Manual
38
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement