Jetwave SIP Trunk Setup Guide
DSX
JetWave SIP Trunk Setup
April 23, 2011
Issue 1.01
NEC Corporation of America
4 Forest Parkway, Shelton, CT 06484
JetWave SIP Trunk Setup
DSX
1.01
Copyright 2011
NEC Corporation of America
6535 N. State Highway 161
Irving, TX 75039-2402
Communications Technology Group
Revision History
Issue
Date
1.00
3/18/11
•
Initial release.
1.01
4/23/11
•
Updated required software level, expanded RTP port forwarding
range, and added System Administrator screen shots.
•
Removed requirement for 1104-09.
•
Line Phone Numbers should now be a DID number provided by
Jetwave, not a username.
NEC Corporation of America
Revisions
Page 2 of 7
April 23, 2011
DSX
JetWave SIP Trunk Setup
1.01
Contents
1 Overview................................................................................................................................................ 4 2 JetWave Setup ...................................................................................................................................... 4 3 System Router Setup............................................................................................................................. 4 3.1 NAT and SIP....................................................................................................................................... 4 3.2 Port Forwarding .................................................................................................................................. 4 4 DSX Setup ............................................................................................................................................. 4 4.1 Software Level .................................................................................................................................... 4 4.2 Assign SIP Lines................................................................................................................................. 5 4.3 Select the SIP Trunk Provider Type ................................................................................................... 6 4.4 Set Up the SIP Trunk Registration...................................................................................................... 6 4.5 Codec Setup ....................................................................................................................................... 7 4.6 Assign Phone Numbers to your SIP Lines.......................................................................................... 7 4.7 Outgoing Caller ID .............................................................................................................................. 7 4.8 Fax Setup ........................................................................................................................................... 7 Tables
Table 1: JetWave Account Information ........................................................................................................ 4 NEC Corporation of America
Page 3 of 7
April 23, 2011
DSX
1
JetWave SIP Trunk Setup
1.01
Overview
The DSX is compatible with JetWave SIP Trunking. This setup guide summarizes the account information
you will receive from JetWave and provides step-by-step instructions on how to program that information
into the DSX.
You must set up JetWave SIP trunks as DID lines. All the feature available with other types of DID lines
are also available with JetWave SIP trunk lines. For details on the features available with DID lines, refer
to the on-line DSX Software Manual at: http://www.necdsx.com/docs/dita/dsx_v3_complete/index.html
2
JetWave Setup
To set up your SIP trunking account, contact JetWave at http://www.jetwaveservices.com. Once your
account is set up you need the service information:
Table 1: JetWave Account Information
Option
Server Address
3.1
The Server Address is the SIP registration domain for your
JetWave SIP trunks. When your SIP trunks initially register
they use this address.
Username
This is the username that JetWave uses to authenticate your
registration.
Password
This is the password required with your Login.
DID Number(s)
3
Description
These are the telephone numbers that users will dial to reach
you over your JetWave SIP trunks.
System Router Setup
NAT and SIP
In the router to which the DSX is connected, enable NAT and disable all special SIP management
features (such as SIP ALG).
3.2
Port Forwarding
Forward UDP ports 5060 and 1024 through 1215 to the DSX system’s IP address.
4
4.1
DSX Setup
Software Level
3.31.96 or higher.
NEC Corporation of America
Page 4 of 7
April 23, 2011
DSX
4.2
JetWave SIP Trunk Setup
1.01
Assign SIP Lines
1231-01: IP Lines [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
The first DSX SIP line is the first line beyond the last assigned line. Each SIP line uses an IP
resource (licensed VoIP port) in DSX. The maximum number of VoIP licenses is 8 in DSX-40 and
16 in DSX-80/160.
Example with DSX-40:
•
The first SIP line in a DSX-40 without a COIU expansion card is line 5. Available SIP line
numbers are 5-12.
•
With the COIU expansion card installed, the first SIP line is line 9. Available SIP line
numbers are 9-16.
•
DSX-40 supports a maximum of 8 VoIP licenses. When the total number of licenses are in
use, only Peer-to-Peer calls are available.
Example with DSX-80/160:
•
The first SIP line in a DSX-80/160 with a single 8COIU card is line 9. Available SIP lines
are 9-17.
•
The last line number in DSX-80/160 is 64. In a system with an 8COIU and two T1/PRI
cards, this will limit the available number of SIP lines.
•
DSX-80/160 supports a maximum of 16 VoIP licenses. When the total number of licenses
are in use, only Peer-to-Peer calls are available.
1232-01: IP Line Provider Number [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
Assign each SIP line in DSX to a provider number (1 or 2). DSX supports up to two providers
simultaneously.
Example: If JetWave is your only SIP trunk provider, assign all the SIP lines designated in 1231-01
to provider 1.
1232-02: IP Line Username [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
1232-03: IP Line Password [SYSTEM: PORTS: IP LINES: IP LINE ASSIGNMENT]
These options are not used with JetWave SIP trunks.
NEC Corporation of America
Page 5 of 7
April 23, 2011
DSX
4.3
JetWave SIP Trunk Setup
1.01
Select the SIP Trunk Provider Type
1831-01: Provider Number [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2)]
Select the provider number you want to set up. This selection corresponds to the provider number
you assigned to the SIP lines in 1232-01.
Example: If JetWave is your only SIP trunk provider, and you have chosen provider 1 in 1232-01,
select provider 1 for this option also.
1831-02: Provider Type [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): SERVICE PROVIDER]
Dial 13 to choose Jetwave as the type for the provider selected in 1831-01.
1831-03: Provider Name [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): DESCRIPTION]
The provider name is an optional 18-character entry that describes the provider. Enter any name
you like – the entry does not affect provider setup or registration.
1831-04: Profile [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): PROFILE]
Select the VoIP profile that the system will use when connecting to the SIP trunk provider. The
entry you make here corresponds to the profiles set up in programs 1811-1815. Choose profile 4.
4.4
Set Up the SIP Trunk Registration
1832-01: Provider IP Registration [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): SERVER ADDRESS]
Select the provider number you want to set up (see 1831-01) and enter the Table 1 Server Address
as it was provided to you by JetWave. This option uses the text entry method.
1832-02: Registration Type [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): REGISTRATION TYPE]
Choose the IP line registration type. DSX IP lines can share the same registration (01: Common) or
have a unique registration for each line (02: Per Line). For JetWave, choose 01: Common.
1832-03: Account Username [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): USER]
Enter the username for your JetWave SIP trunk account. This option uses the text entry method
and is the Username entry in Table 1.
1832-04: Account Password [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): PASSWORD]
This option is the password associated with the Account Username assigned in 1832-03. The
password can be up to 24 characters long. This is the Password entry in Table 1.
1832-05: Proxy [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): PROXY ADDRESS]
1832-06: SIP Type or Service (ToS) [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): SIP TOS]
1832-07: RTP Type of Service (ToS) [SYSTEM: VOIP: PROVIDERS: PROVIDER (1 OR 2): RTP TOS]
These options are not used with JetWave SIP trunks.
NEC Corporation of America
Page 6 of 7
April 23, 2011
DSX
4.5
JetWave SIP Trunk Setup
1.01
Codec Setup
1812: Codecs [SYSTEM: VOIP: PROFILE 4: CODECS]
For JetWave SIP Trunks, for Profile 4 set:
- Codec 1 to G.711, 40mS Frame Size.
Set all other priorities to None.
4.6
Assign Phone Numbers to your SIP Lines
3101-07: Telephone Number [LINES: CONFIG: SETUP: TYPE: PHONE NUMBER]
For each of your SIP lines, enter a DID Number from Table 1 as the Phone Number entry.
4.7
Outgoing Caller ID
JetWave delivers Caller ID to outside callers using the following priority:
1. 2101-01: Outgoing ANI ID [STATIONS: CONFIG: SETUP: TYPE: ANI ID]
2. 3101-07: Telephone Number [LINES: CONFIG: SETUP: TYPE: PHONE NUMBER]
3. 1011-02: Telephone Number [SYSTEM: CONFIG: SETUP: IDENTIFICATION: PHONE NUMBER]
4.8
Fax Setup
Contact JetWave for fax solutions. Normally, you should not use your JetWave SIP trunks for fax.
NEC Corporation of America
Page 7 of 7
April 23, 2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement