IC693PWR321

IC693PWR321
This Datasheet for the
IC693PWR321
Power Supply, 120/240 VAC, 125 VDC, Standard, Battery not included
http://www.cimtecautomation.com/parts/p-14693-ic693pwr321.aspx
Provides the wiring diagrams and installation guidelines for this GE Series 90-30
module.
For further information, please contact Cimtec Technical Support at
1-866-599-6507
[email protected]
4
AC/DC Input Power Supplies
IC693PWR321 Standard Power Supply, 120/240 VAC or 125 VDC Input
The IC693PWR32 is a 30 watt supply that can operate from an input voltage source in the range
of 85 to 264 VAC or 00 to 300 VDC. This power supply provides three outputs:
Ŷ
+5 VDC output,
Ŷ
+24 VDC Relay power output which provides power to circuits on Series 90-30 Output Relay
modules.
Ŷ
Isolated +24 VDC, which is used internally by some modules, can also be used to provide
external power for 24 VDC Input modules.
The load capacity for each output of this power supply is shown in the following table.
Table 4-2. IC693PWR321 Power Supply Capacities
Catalog
Number
IC693PWR32
Load
Capacity
30 Watts
Nominal
Input
Output Capacities (Voltage/Power *)
00 to 240 VAC or
25 VDC
+5 VDC
5 watts
+24 VDC Isolated
20 watts
+24 VDC Relay
5 watts
*Total of all outputs combined cannot exceed 30 watts.
IC693PWR321
GE Fanuc
SERIES 90-30
PWR
SYSTEM
STATUS
INDICATORS
OK
RUN
BATT
STANDARD
POWER SUPPLY
PROGRAMMABLE CONTROLLER
INPUT
∼
100-240 VAC
50/60HZ 90 VA
CONNECTIONS
FOR
AC/DC POWER
SOURCE
125 VDC, 50W
INTERNAL
POWER SOURCE
FOR
MODULES REQUIRING
24VDC
+
24 VDC
OUTPUT
0.8A MAX.
LITHIUM
BACK-UP
BATTERY
B
A
T
T
E
R
Y
RS-485
COMPATIBLE
SERIAL PORT
BATTERY
CONNECTORS
Figure 4-1. Standard AC/DC Input Power Supply - IC693PWR321
Power supplies must be installed in the leftmost slot in all baseplates.
4-2
Series 90-30 PLC Installation and Hardware Manual – August 2002
GFK-0356Q
4
Table 4-3. Specifications for IC693PWR321 Standard AC/DC Input Power Supply
Nominal Rated Voltage
Input Voltage Range
AC
DC
20/240 VAC or 25 VDC
Input Power
(Maximum with Full Load)
Inrush Current
Output Power
90 VA with VAC Input
50 W with VDC Input
4A peak, 250 milliseconds maximum
5 VDC and 24 VDC Relay: 5 watts maximum
24 VDC Relay: 5 watts maximum
24 VDC Isolated: 20 watts maximum
NOTE: 30 watts maximum total (all three outputs)
5 VDC: 5.0 VDC to 5.2 VDC (5. VDC nominal)
Relay 24 VDC: 24 to 28 VDC
Isolated 24 VDC: 2.5 VDC to 28 VDC
Output Voltage
Protective Limits
Overvoltage:
Overcurrent:
Holdup Time:
GFK-0356Q
Chapter 4 Power Supplies
85 to 264 VAC
00 to 300 VDC
5 VDC output: 6.4 to 7 V
5 VDC output: 4 A maximum
20 milliseconds minimum
4-3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement