Maytag Range MGR5750BDB

Maytag Range MGR5750BDB
www.dexpress.com
DIMENSION EXPRESS
This Data Sheet Includes Information On
Maytag
•
Product Model Number (s):
•
Free Standing Gas Ranges:
MGR5750BDW, MGR5750BDQ and MGR5750BDB
•
Dimensions (Actual Size)
Height of cooking surface: 35 7/8"
Fax on Demand (775) 833-3600
29 7/8"
(not to scale)
•
Height overall: 46 3/4"
46 3/4"
Case width: 29 7/8"
Depth NOT including handle: 25 1/2"
35 7/8"
Door swing: 20"
20"
Height at full leg adjustment: 36"
Height at 0" leg adjustment: 35 1/2"
•
Additional Information
•
• Units depth including door handle is 28 1/8".
• Can be installed with the back against (0") a vertical
combustible wall, and the sides below the cooktop
surface against (0") combustible base cabinets.
• Electrical requirements: 120 VAC,60Hz. 15 amp
grounded circuit protection is required.
• Gas requirements: Gas supply line should be 3/4".
Install a manual shutoff valve in an accessible location
in the gas line external to this appliance for the purpose
of turning on or shutting off gas to the appliance. The
appliance is shipped from the factory equipped for use
with natural gas and can be converted to LP gas in the
field . The maximum gas supply pressure for both LP
and natural gas is 14" WC. Minimum Pressure for
Natural gas is 4" WC. Minimum Pressure for LP gas is
10" WC.
• Proper operation requires use of range hood.
• Cabinetry over cooktop : 30' minimum clearance
between the top of the cooking surface and the bottom
of an unprotected wood or metal cabinet. 24" minimum
when bottom of wood or metal cabinet is protected by
not less than 1/4" flame retardant millboard covered
with not less than no. 28 MSG sheet steel, 0.015"
stainless steel, 0.024" aluminum or copper.
Door open
25 1/2"
1"
Locate gas line
within shadded
area
Wall View
(not to scale)
Locate electrical
supply outlet (flush
with wall) within
hashed area. Area is
13" W X 9" H.
located 9 3/8" above
floor and 1 1/2" from
right wall.
28"
Electric
Location
18"
Gas Location
2 1/4"
Wall View
(not to scale)
30"
See page 2 for additional information
Upper cabinets
can only be 13"
deep maximum.
Over range
cabinet is NOT
recommended.
30" Min.
18"
Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall
not exceed $50.00.
Copyright © Dimension Express, 2002.
255
• NEVER reuse Data Sheets. Data Sheets are subject to change without
notice. Dimension Express is a FREE service bureau and is updated daily,
it makes far more sense to spend the time necessary to request new Data
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.
36"
Countertop
height
Range
Side clearance
from cooktop to
18" above the
cooktop is 3" on
each side (see
solid arera)
30" Minimum
cutout width
• Call Dimension Express if you have any questions at (775) 833-3633 •
• Always refer to a current Code at a Glance or manufacturer directory •
• Data Sheet codes change on the first of odd numbered months at 12:01am •
BN • A255B149 • • 032603 • 95657 • 45163
www.dexpress.com
DIMENSION EXPRESS
Fax on Demand (775) 833-3600
This Data Sheet Includes Information On
Maytag
Page 2
•
Product Model Number (s):
•
Free Standing Gas Ranges:
MGR5750BDW, MGR5750BDQ and MGR5750BDB
Additional Information:
• To eliminate the hazard of reaching over heated surface units,
cabinet storage space located above the surface units should be
avoided. If cabinet storage is to be provided, the hazard can be
reduced by installing a range hood that projects horizontally a
minimum of 5" beyond the bottom of the cabinets.
• For Free-standing installations the cutout opening width is 30" ± 1/16"
minimum. The height of the countertop is 36" and countertop depth is
25".
• MGR5750ADA : Monochromatic Almond.
• MGR5750ADW : Monochromatic White.
Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or
outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.
Copyright © Dimension Express, 2002.
149
• NEVER reuse Data Sheets. Data Sheets are subject to change without
notice. Dimension Express is a FREE service bureau and is updated daily,
it makes far more sense to spend the time necessary to request new Data
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.
• Call Dimension Express if you have any questions at (775) 833-3633 •
• Always refer to a current Code at a Glance or manufacturer directory •
• Data Sheet codes change on the first of odd numbered months at 12:01am •
BN • A255B149 • • 032603 • 95657 • 45163
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement