IP Power 9258 DS Power Distribution Unit User Manual
Below you will find brief information for Power Distribution Unit 9258 DS. The IP Power 9258 DS is a state of the art Power Distribution Unit (PDU) & Remote Power Control (RPC) system. The 9258 DS can be used for various applications including: Power Management, Server Management, Internet Controllable Timer, System Integration and much more. This device allows you to control up to 8 separate devices via the internet. By using a web browser, you can remotely control the power of the 9258 DS from virtually anywhere.
Advertisement
Advertisement
IP Power 9258 DS
User Manual
Firmware Version: 4.03
Date Released: 11/09/2012
- 1 –
Ref: DS9258Y90M02
Warning:
Any changes made to this equipment without permission may cause damages to the device!
IMPORTANT NOTICE
1. IP Power 9258 DS was designed for indoor use, we carry no responsibility for possible damages caused by outdoor use, especially in the rain.
2. Please use the power adapter provided by the dealer, we carry no responsibility for the possible damage from using power adapters not .
4. Do not shake the IP Power 9258 DS in any fashion
5. Please contact the dealer If IP Power 9258 DS is not working properly.
Copyright © 2009 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of us.
All trademarks and products mentioned in this document are the properties of us.
- 2 –
Ref: DS9258Y90M02
Table of Content
F
RONT
V
IEW
..................................................................................................... E
RROR
!
B
OOKMARK NOT DEFINED
.
- 3 –
Ref: DS9258Y90M02
Set Device DNS Command ...................................................................... Error! Bookmark not defined.
- 4 –
Ref: DS9258Y90M02
1.) Welcome
Introduction
The IP Power 9258 DS is a state of the art Power Distribution Unit (PDU) & Remote Power Control (RPC) system. The 9258 DS can be used for various applications including: Power Management, Server
Management, Internet Controllable Timer, System Integration and much more.
This device allows you to control up to 8 separate devices via the internet. By using a web browser, you can remotely control the power of the 9258 DS from virtually anywhere.
What makes this device different from other PDU’s is that it has a dual switch design.
Unlike other PDU or RPC units the 9258 DS is completely safe. The dual switch design cuts off the power and will eliminate any most electrical threats that other systems may have.
Minimum System Requirements
Operating Systems: WINDOWS Operating Systems (IE5.0+SPI) & LINUX
RJ45 LAN & Internet HUB & Switch
Internet (For remote access) or Ethernet Network (Internal Network use) with some type of Internet connection, (i.e. ADSL, Cable, Dial up or any other forms of Internet service)
- 5 –
Ref: DS9258Y90M02
2.) Product Overview
Features
1. Dual Switch Design for extra safety and protection
2. HUB function four 4 RJ45 connections
3. Auto-ping (Watch dog) Device Auto Restart / Reboot.
4. Supports: RJ45(HUB), TCP/IP, Http API, Web Server, SMTP Server, SNMP & TRAP, DHCP,
DDNS, CNT, XML
5. 8 Power control output
6. 2 Main power inputs.
7. 1 RS232 port for System Integration.
8. Design Pressure System: Prevent interference with power noise design. (Second stage isolation)
9. Scheduler System for date sensitive control
10. Http commands through Internet
11. Log Capability
12. CNT Technology: No Port Forwarding Needed in Router – Just Plug & Play
13. IP Service: Easily Find your device on the internet without having to remember complicated IP’s
14. Light Aluminum Design
15. Supports UPNP (Universal Plug & Play)
Specification
1. Input Power Voltage: 90-240 VAC
2. Input Frequency: 50/60 Hz full range
3. Dimension: 440x235x40 mm 1.8kg
4. Reliability testing Certification MBTF 200,000 hrs +
5. Operating temperature range: 0 - 50 degrees Celsius.
- 6 –
Ref: DS9258Y90M02
1.) 9258 DS Unit x 1
2.) 9258 DS Installation CD
Package Contents
3.) Extra Fuse x 1: Located in the power input of the 9258 DS
Refer to installing fuse section
4.) RJ45 Cable x 1 (Optional)
5.) Input Power Cable x 2
(Optional)
- 7 –
Ref: DS9258Y90M02
3.) Interface Description
Front View
4 Port Ethernet Hub:
Connect up to 4 separate devices with the built in hub.
1 Serial Ports:
Serial Port 1: Regular Speed
Reset Button:
To reset to original manufacture settings, hold down the reset button with a pen or a pin for 15 seconds until will hear a long beep sound.
Power Status Indicator:
The Power Status indicator
- 8 –
Ref: DS9258Y90M02
Rear View
Rear View
Rear View
8 Output Power Ports:
Connect up to 8 separate devices that will be controlled by the 9258 DS. Ports 1-4
2 Input Power Ports:
The input power sends power to the 2 sets o
9258.
2 Power Switch:
The 2 Power switch turns on the input power
Ports 1-4: Switch 1
Ports 5-8 Switch 2
Replaceable Fuse: The 9258 uses a
TYPE
：U/C GFE 10A 250V (PF)
- 9 –
Ref: DS9258Y90M02
4.) Quick Start Guide
Quick Hardware Setup
*Before you plug in the device make sure you have the appropriate input plugs.
* For 220-250V, please use power cable that can support 10A current.
Max Output Current: (total of each four outlets) 10A, (each outlet) 6A.
* For 100-120V, please use power cable that can support 15A current.
Max Output Current: (total of each four outlets) 15A, (each outlet) 6A
1.) Make sure that all the package contents are included, if anything is missing please contact the store.
2.) Plug the RJ45 (Ethernet Cable) from your router or modem to any of the 4 ports on the
9258 DS.
3.) Plug in the Input Power Plugs into the device and then into the wall of your device.
4.) Plug in the devices that you want to control in the output ports of the 9258 DS
Quick Device Setup
Using IPEdit
1.) Click on the REF button, and wait a few seconds. IPEdit will automatically detect the network settings and setup the device.
2.) Once settings have been detected hit the apply button to apply the new settings.
3.) Hit yes to confirm and Enter the login and password for the Device to Approve changes
- 10 –
Ref: DS9258Y90M02
4.) Then hit the rescan button on IPEdit to confirm the changes have been made.
5.) Once you have found your device double click on the device and the internet explorer will pop up and ask for your login information.
6.) Type in your password & login and the device is ready to use.
* Remember that to access your device from the outside network, you will need to port forward the
IP Address of your device.
5.) Hardware Setup
1.) Connect the IP Power 9258 DS to a HUB or Router with a RJ45 network cable.
2.) Connect the HUB or Router to the internet (May through ADSL/XDSL modem).
3.) Connect the power adapter to the IP Power 9258 DS.
4.) Connect the power adapters of under control electric equipment to corresponding out port of IP Power 9258-Pro.
Turn on your computer and the power adapter of IP Power 9258-Pro
* For 220-250V, please use power cable that can support 10A current.
Max. output current: (total of each four outlets) 10A, (each outlet) 6A.
* For 100-120V, please use power cable that can support 15A current.
Max. Output current: (total of each four outlets) 15A, (each outlet) 6A
- 11 –
Ref: DS9258Y90M02
6.) Software Setup
The software for the device is located on the Media Link-IP Family CD that came with the device. IP
Power Pack is located on the main page of the CD. Please follow the directions carefully and install the necessary files
The IP Power Necessary Software:
* IPEdit : For search our IP product , access, modify basic configurations of IP POWER 9258DS.
* IP POWER Center : Own software for CNT and multiple IP power to control in one software .
Installing IP Power Software
1.) First place the Media Link-IP Family CD that came with your device into your CD/DVD Rom drive.
The CD should auto run but if it does not go to the CD/DVD Rom drive and select the file
“autorun.html”.
2.) Once the CD has started, go to the IP Power section and click and install the following:
IPedit:
IP Family Program used to search, access, modify basic configurations of IP Family products.
IP Power Center:
Multiple IP Power device manager to control the ON and OFF of the managed devices. (For IP Power
9258 Ping , 9280, 9211, 9222.)
3.) Once installation is complete please double click the IPEdit to configure and search for your device.
- 12 –
Ref: DS9258Y90M02
Using IP Edit
IPEdit is a search tool designed to setup and access the device.
It comes with the IP Service feature which searches for the device easily without having to remember long complicated IP addresses. Instead, this technology allows the user to use a name method to find his or her device through the internet. .
Please make sure you have the most updated version of IPEdit. Contact your distributor to provide you with the newest updated IPEdit.
1.) After correctly installing the IPEdit software, double click on the IPEdit icon to run the program.
2.) Open IPEdit and any device in the same network should automatically be detected and listed in the local devices sections.
The devices will need to be setup correctly through IPEdit so that you can properly access the device.
- 13 –
Ref: DS9258Y90M02
3.) Setup the Device:
All devices will need to be on the same network if not the device cannot be accessed and will not be detected. a. Quick Easy Setup (Recommended)
7.) Click on the REF button, and wait a few seconds. IPEdit will automatically detect the network settings and setup the device.
8.) Once settings have been detected hit the apply button to apply the new settings.
9.) Hit yes to confirm and Enter the login and password for the Device to Approve changes
10.) Then hit the rescan button on IPEdit to confirm the changes have been made. b. Custom Setup (Advance Users)
1.) Highlight the device on the local devices section and on the right side of IPEdit all network information on the device will be displayed.
- 14 –
Ref: DS9258Y90M02
If the device is not on the same network a Red Exclamation mark will appear in the IP
Network information section
2.) To setup the device, type in the correct Gateway and IP Address.
* Gateway Address: The gateway address can be obtained in Windows under the network connections page
* IP Address: Make sure the first 3 sections of the IP Address matches the gateway address.
Example: Gateway Address – 192.168.1.1 IP Address – 192.168.1.xxx
3.) Once the Default Gateway information has been obtained, enter the correct information into IPEdit and hit the submit button.
4.) Then hit the rescan button on IPEdit to confirm the changes have been made
- 15 –
Ref: DS9258Y90M02
IP Service
How to use IP Service on IPEdit:
IP service allows the user to directly connect to his / her device through the internet without having to remember long confusing IP Address. Instead with this IP Service Technology, the user only has to remember the name of the device that the user has selected. Then the user can connect to IP Service, type in the device name, and connect directly to the device.
First if you have de-activated IP Service on your device make sure you re-enable it. (Refer to your manual if you have questions on How to activate IP Service)
1.) Open IPEdit, the device will show up in the Local Device Section. If you have not selected a name for the device, please refer to the section on the manual labeled: “Naming your device”.
2.) To start IP Service, Hit the green connect button on the top of IPEdit.
3.) Once you have been connected search for your device by typing in at least the first 3 letters that you named your device with. Then hit the search button.
4.) Double click on your device and a Internet Explorer window will appear connecting directly to your device.
*Remember: It is crucial to have the IP Address of the device port forwarded from the router that you are using so you can connect to your device from anywhere. Please refer to your routers user manual on how to port forward your device.
- 16 –
Ref: DS9258Y90M02
7.) Hardware Interface
Hardware Reset
To reset the device back to manufacturer default, use a small pen or pin and press the reset button and hold for a minimum of 10 seconds. Once you hear a “beep” sound the device will be reset.
Serial Port Control
Please view the Controlling the Device section on this manual on page 31.
How to Replace Fuse
1.) The fuse is located between the power switch and the power input plugs.
2.) Carefully remove the fuse holder with a flat screwdriver.
3.) The fuse can be purchased at most electrical stores
Model: U/C GFE 10A 250V (PF)
- 17 –
Ref: DS9258Y90M02
8.) Web Interface
Connection to your Device
Once you have the 9258 DS setup correctly.
Open IPEdit and double click on your IP Power 9258 DS.
A Internet Explorer browser screen pop up with the login screen for the 9258 DS.
Default IP: 192.168.1.100 (When 9258 DS is connected to PC directly)
Default Login: Admin
Default Password: 12345678
The Control Console
The Right Panel of the Web Interface controls the functionality and setup of the IP Power 9258 DS.
- 18 –
Ref: DS9258Y90M02
Power Setup
Power Controls
The Power Controls setting allows you to control the devices that are connected to the 9258 DS.
Name: The name field allows you to enter a name of the Power that you are controlling. Simple type in the name of the device next to the outlet that it is connected to, then hit apply.
Control: Control allows the user to actively control the device on each port. To turn off or turn on the device, select the control you want then hit the apply button
Timer: The timer allows you to turn On or Off your device with a delay. Please view the example below:
Power 1: The device will turn on when you hit the apply button and after 5 seconds the device will be turned off.
Power 2: The device will be off and when you hit apply after 10 seconds then the device will turn on.
- 19 –
Ref: DS9258Y90M02
System Configuration
System Setup
The System Setup page is where you would configure the basic IP information needed for the device to work properly
IP Address: The IP Address of the 9258 DS can be specified here. If you are using a hub or router, the IP address may be selected for you already. Otherwise you can manually select the IP Address here.
Subnet Mask: The Subnet Mask Address of the 9258 DS can be specified here. If you are using a hub or router, the IP address may be selected for you already. Otherwise you can manually select the IP Address here.
Default Gateway: The Default Gateway is given by a router or hub and this is where that information would be specified.
DNS: The DNS is the Domain Name Server. This information can be obtained by contacting the ISP
DHCP Client: The DHCP client allows the 9258 DS to use DHCP to obtain the IP Information from a Hub or Router.
Beeper: The Beeper turns on/off the beeper sound from the 9258 DS. When commands are sent a beep sound will appear
.
Http Command Verification: The HTTP Verification turns on or off the HTTP Command mode. This mode allows you to send commands directly to the device via internet without having to enter the device.
Device Name: In this section you can change the name of the 9258 DS for easier identification purposes.
It is also a way to find your device using IP Service.
Release Version: Displays information on the Firmware version and release date.
- 20 –
Ref: DS9258Y90M02
DDNS
The DDNS section allows you to setup the 9258 DS with a DDNS server (i.e. www.dyndns.com
). The the server has been setup correctly, enter the necessary information into the 9258 DS DDNS settings.
DDNS Server IP: Input IP Address of the DDNS server.
Your Domain: Type in the Domain Name that you selected for your DDNS server
DDNS Username: Enter the DDNS Username
DDNS Password: Enter the corresponding Password for your DDNS account
Enable DDNS: Select Enable or Disable to turn on or off DDNS settings for the 9258 DS
Proxy Enable: Select enable or disable if any proxy servers are used.
Proxy IP: Enter the proxy server IP Address of the proxy server here.
Proxy Port: Enter Port of the proxy server
- 21 –
Ref: DS9258Y90M02
The 9258 DS has an e-mail function that can be used in various scenarios and conditions. When a power port is activated or deactivated, the device will send an email.
When the scheduler is used the device will also send emails when ports are activated or deactivated.
To send out mail successfully , please do set the DNS correctly . You can check with your ISP for correct
DNS information.
Smtp Server: Input the server name of the mail server.
Smtp Port: Input the outgoing Server Port
Pop 3 Server: Input the incoming pop 3 server information
Username: Enter E-mail username
Password: Enter E-mail password (no longer than 8 characters.)
Sender: Enter Sender Email Address
Receiver 1-3: Enter up to 3 receivers
Subject: Enter the email Subject line
- 22 –
Ref: DS9258Y90M02
Mail Body: Enter Email Body information.
Schedule Ports 1-4 & Ports 5-8
The scheduler function allows you automatically control the device(s) without having to login. This function allows you to turn on or turn off, cycle power of your devices at scheduled times. To use the this function some key parameters must be set correctly.
Power
Date: Input the date for the device to activate power controls. Format: (YYYY-MM-DD)
Time: Enter the exact time of when the device will be activated on. Format: (HH:MM:SS)
Note: Hour is based on a 24hr military time.
Frequency: Select the number of times this event will be activated (Disable, Just Once, Everyday,
Workdays, Weekend)
Disable: Disables the scheduler
Just Once: Activates the schedule only once
Everyday: Activates everyday until schedule has been deactivated
Workdays: Activates every week from Monday – Friday until deactivated
Weekend: Activates every week on Saturday & Sunday until deactivated
Power On / Off: Set the power to On or Off when the scheduler is activated
- 23 –
Ref: DS9258Y90M02
IP Service
The IP Service functionality allows your 9258 DS to easily be found on the internet by using IP Service.
This function allows you to search for your device on IPEdit without having to remember long IP Addresses.
Instead all you need is the name of your 9258 DS and you can access it there. Refer to Page 13 of the
manual on how to use IP Service
On / Off: This allows you to turn on or off IPEdit. By default this function is enabled
Server Address: The IP Service Server address by default is 220.135.169.136. Please contact your
distributor for information on how to setup your own IP Service
*Note: To use IP Service Make sure that you have port forwarded the IP Address of the 9258 DS. IF not you will not be able to access your device.
- 24 –
Ref: DS9258Y90M02
Ping
The Auto-ping functionality allows the 9258 DS to check if the device have malfunctioned or needs to be restarted. If the device is no working correctly the 9258 Ping will activate the action that you have selected to reinstate the state of the device
Outlet: A description of which on let to use Ping function
Enable: Disable or Enable ping settings
Ping Address: Specify the IP Address to Ping
Ping Failures: The number of ping failures before the Action is activated.
Action Delay (Seconds): When Ping Failures is reached the number of seconds delay before action is activated.
(I.E some systems or computers that require a shut down time)
Startup Delay (Seconds): The number of seconds it takes the attached devices to startup. Once those devices start, the Start up Action will be activated to continue pinging or stop pinging.
Start up Action: After start up Delay has been reached the start up action will either Continue Pinging or
Stop Pinging
Action: When the number of Ping Failures have been reached. The 9258 will either
Ping Time Interval (Seconds): The number of seconds between each ping
Ping Response Time (Milliseconds): The number of milliseconds the device will wait for a response from the pinged device if no ping is detected within this time it will be considered a ping failure.
Please view the example below for more details:
- 25 –
Ref: DS9258Y90M02
In the picture above:
1. Power1 Ping function is enabled
2. The 9258 DS will ping the web address www.sample.com
3. If there is a response within the Ping Response Time the 9258 DS will send another ping signal the set Ping Time Interval which is 3 seconds for this example.
4. If the 9258 DS does not receive a response from the device it will constitute a Ping Failure.
5. After 3 consecutive failure the device will go to the Action Delay section. In this case the device will delay for 3 seconds.
6. When action delay has been reached the Action will be set off. Here we have set the 9258
DS to Reset the device.
7. Once the device has been reset the 9258 will go into Startup Delay mode. In this case it is
3 seconds.
8. After the startup delay mode has been reached the 9258 will check the Startup Action whether to continue or stop pinging the device. Here we have it set to Continue.
Then the process starts all over.
- 26 –
Ref: DS9258Y90M02
Network Wakeup
The network wakeup function is used to boot up a computer that has the Wake on Lan functionality. Just enter the MAC address of the target computer and the 9258 DS will be able to turn on the device.
Change Password
The change password page allows you to change your password for the 9258 DS. To change the password:
5.) Enter the current password.
6.) Type in the New Password
7.) Confirm New Password
Firmware Update
Follow the instructions carefully and update with caution.
1.) Click the update Button.
2.) Wait for the continue button to load properly. Then hit the continue button.
- 27 –
Ref: DS9258Y90M02
3.) Once you have clicked continue the 9258 DS will take you to the update page.
4.) Browse for the update file
5.) Hit the update button and wait for as least 1 minute for the upgrade to complete.
Time Change
The change time feature allows you to change time of your device by setting the time or selecting a NTP server.
Set Date and Time
To set the time of the device enter the Date/ Time with
Date: YYYY-MM-DD Time:24HH-MM-SS
NTP Server
The NTP Server allows the 9258 DS to check with a NTP (Network Time Protocol) to constantly keep the internal clock of the device updated. The network environment must connect to Internet.
- 28 –
Ref: DS9258Y90M02
9.) Controlling the Device
CGI HTTP Commands
CGI Commands allow you to easily integrate the 9258 DS with other systems and programs. Please read the instructions carefully on how to use the Http:// Commands
To use http:// Commands open up a web browser and type in the command that you would like to use.
The command structure looks like this http://xxx.xxx.x.xxx/set.cmd?user=USER+pass=PASSWORD+cmd=COMMAND
Set Power Command
Command http://IP /set.cmd?cmd=setpower+p6x=y+p6x=y+p6x=y+p6x=y+p6x=y+p6x=y+p6x=y+p6x=y x = 1~8 means output number y = 1/ 0 means power on/off . 1 means power ON , 0 means power off
Example : http://IP /set.cmd?cmd=setpower+p61=0+p62=1+p63=0+p64=1+p65=0+p66=+p67=0+p68= means turn OFF of output 1,3,5&7 means turn ON of output 2,4,6&8
Set Power Delay Command
Command http://IP /set.cmd?cmd=setpower+p6x=y+p6xn=0+t6x=A x = 1~8 means output number y = 1/ 0 means power on/off . 1 means power ON , 0 means power off
A = 1~9999 means delay second .
Example :
Turn Output #1 as power on and then turn off after 30 seconds http://192.168.1.123
/set.cmd?cmd=setpower+p61=1+p61n=0+t61=30
- 29 –
Ref: DS9258Y90M02
Set Name Command
Command: setportn+ch=Port Number+porn=Name of Port http://xxx.xxx.x.xxx/set.cmd?user=admin+pass=12345678+cmd=setportn+ch=
Port Number
+portn=
Name of Port
Example:
http://192.168.1.39/set.cmd?user=admin+pass=12345678+cmd=setportn+Ch=1+portn=test1
Response Message: Port1Name_Set_Ok
Get Name Command
Command: getportn+ch=Port Number+portn=Name of Port
Format: http://xxx.xxx.x.xxx/set.cmd?user=admin+pass=12345678+cmd=getportn+ch=
Port
Number +portn= Name of Port
Example:
http://192.168.1.39/set.cmd?user=admin+pass=12345678+cmd=getportn+ch=1+portn
Response Message: Port1Name:test1
Get Firmware Version Command
Command:
GetVersion
Format: http://xxx.xxx.x.xxx/set.cmd?user=admin+pass=12345678+cmd=getversion
Example:
http://192.168.1.42/set.cmd?user=admin+pass=12345678+cmd=getversion
Response Message: Version:V1.025
Get Time Command
Command:
- 30 –
Ref: DS9258Y90M02
getsysclock
Format: http://xxx.xxx.x.xxx/set.cmd?user=admin+pass=12345678+smd=getsysclock
Example:
http://192.168.1.9/set.cmd?user=admin+pass=12345678+cmd=getsysclock
Response Message: YR:2008 MO:01 DATE:05 HR:11 MN:38 SEC:42
Set Time Command
Command:
setsysclock+y=YYYY+m=MM+d=DD+h=HH+m=MM+s=SS
Date Parameters
y=Year in YYYY format m=Month in MM format d=Day in DD format
Time Parameter
h=Hour in HH (24 hour Military Format) m=Minutes in MM format s=Seconds in SS format
Format: http://192.168.1.100/set.cmd?user=admin+pass=12345678+cmd=setsysclock+y=
YYYY +m= MM +d= DD + h= HH +m= MM +s= SS
Example:
http://192.168.1.100/set.cmd?user=admin+pass=12345678+cmd=setsysclock+y=2008+m=7+d=30+h
=15+m=44+s=55
Response Message: YR:2008 MO:07 DATE:30 HR:15 MN:44 SEC:55
Set Device Gateway Command
Command: setfactory+gateway=xxx.xxx.x.xxx+confirm=factoryonly
Format: http:192.168.1.100/set.cmd?user=admin+pass=12345678+cmd=setfactory+gateway=
xxx.xxx.x.xxx
+co
nfirm=factoryonly
Example:
http:192.168.1.100/set.cmd?user=admin+pass=12345678+cmd=setfactory+gateway=192.168.1.1+co nfirm=factoryonly
- 31 –
Ref: DS9258Y90M02
Response Message: Gateway: 192.168.1.1
Turn D HCP ON/OFF
Command: setfactory+dhcp=x+confirm=factoryonly
Format: http://xxx.xxx.xxx/set.cmd?user=admin+pass=12345678+cmd=setfactory+dhcp=(0 =off
1=on)+confirm=factoryonly
Example:
http:192.168.1.100/set.cmd?user=admin+pass=12345678+cmd=setfactory+dhcp=1+confirm=factory only
Response Message:
DHCP: 0 or
DHCP: 1
View Log Command
Command: getlog+num=01~50
Format: http://xxx.xxx.x.xxx/set.cmd?user=admin+pass=12345678+cmd=getlog+num=01~50
Example:
http://192.168.1.42/set.cmd?user=admin+pass=12345678+cmd=getversion
Log No. 1 Newest Log
Log No. 50 Oldest Log
Response Message:
Sample Log:
Power1:ON
Power2:ON
Power3:OFF
Power4:OFF
Power5:OFF
Power6:OFF
Power7:OFF
Power8:ON
Socket1:TurnOn
Socket2:TurnOn
Socket3:TurnOff
- 32 –
Ref: DS9258Y90M02
Socket4:TurnOff
Socket5:TurnOff
Socket6:TurnOff
Socket7:TurnOff
Socket8:TurnOn
LogNO.1 PortState:83-PortAct:ffTime:2008-12-16 17:02:54
What this log shows:
Status of Powers 1-8
Status of Sockets 1-8
Log NO.1
Power: Represents the current status of the outlets.
Sockets: Represents the last changed status of the outlets.
Serial Com (RS-232) Control
Com1
The Com1 allows you to read the status of the 9258 DS. Information can be extracted through this port like an output
1.) Use DB9 cable connect to the COM1 of PC and the RS232 of device
2.) Execute WIN program "Hyper Terminal" : please go to " Start" / "program" /
"Accessories" / "Communications" / "Hyper Terminal" .
3.) Set the "Bits per second" as 19200 at COM1 (Must at COM1)
- 33 –
Ref: DS9258Y90M02
4.) Turn off the device then turn it back on and the screen will display the following information:
SNMP
Initial Setup:
1.) Download Net-SNMP (
http://www.net-snmp.org
) and install the software
2.) Once the software has been installed Register the agent
3.) Register the agent
4.) Start the service
- 34 –
Ref: DS9258Y90M02
SNMP MIB
Get Status MIB
Port 1: 1.3.6.1.4.1.92.59.2.1.0
Port 2: 1.3.6.1.4.1.92.59.2.2.0
Port 3: 1.3.6.1.4.1.92.59.2.3.0
Port 4: 1.3.6.1.4.1.92.59.2.4.0
Port 5: 1.3.6.1.4.1.92.59.2.5.0
Port 6: 1.3.6.1.4.1.92.59.2.6.0
Port 7: 1.3.6.1.4.1.92.59.2.7.0
Port 8: 1.3.6.1.4.1.92.59.2.8.0
Ex: snmpget -v 1 -c public 192.168.1.96 1.3.6.1.4.1.92.59.2.1.0
Response: SNMPv2-SMI::enterprises.92.59.2.1.0 = INTEGER: 0
Integer 0 = Off Integer 1 = On
Get Voltage MIB
1.3.6.1.4.1.92.59.3.1.0
Ex: snmpget -v 1 -c public 192.168.1.96 1.3.6.1.4.1.92.59.3.1.0
Response: SNMPv2-SMI::enterprises.92.59.3.1.0 = INTEGER: 113
Get Current MIB
1.3.6.1.4.1.92.59.4.1.0
- 35 –
Ref: DS9258Y90M02
Ex: snmpget -v 1 -c public 192.168.1.96 1.3.6.1.4.1.92.59.4.1.0
Response: SNMPv2-SMI::enterprises.92.59.4.1.0 = INTEGER: 0
Get Current 2 MIB
1.3.6.1.4.1.92.59.4.2.0
Ex: snmpget -v 1 -c public 192.168.1.96 1.3.6.1.4.1.92.59.4.2.0
Response: SNMPv2-SMI::enterprises.92.59.4.2.0 = INTEGER: 0
Get Temperature MIB
1.3.6.1.4.1.92.59.5.1.0
Ex: snmpget -v 1 -c public 192.168.1.96 1.3.6.1.4.1.92.59.5.1.0
Response: SNMPv2-SMI::enterprises.92.59.5.1.0 = INTEGER: 51
Set Port MIB
1.3.6.1.4.1.92.59.2.1.0
Port 1: 1.3.6.1.4.1.92.59.2.1.0
Port 2: 1.3.6.1.4.1.92.59.2.2.0
Port 3: 1.3.6.1.4.1.92.59.2.3.0
Port 4: 1.3.6.1.4.1.92.59.2.4.0
Port 5: 1.3.6.1.4.1.92.59.2.5.0
Port 6: 1.3.6.1.4.1.92.59.2.6.0
Port 7: 1.3.6.1.4.1.92.59.2.7.0
Port 8: 1.3.6.1.4.1.92.59.2.8.0
Integer 0 = Off
Integer 1 = On
Ex: snmpset -v 1 -c public 192.168.1.96 1.3.6.1.4.1.92.59.2.1.0 integer 1
Response: SNMPv2-SMI::enterprises.92.59.2.1.0 = INTEGER: 1
- 36 –
Ref: DS9258Y90M02
10.) XML Functionality
The 9258 DS supports XML. Before you can start using it you will need to enable it by using the http command: http://xxx.xxx.x.xxx/Set.cmd?user=admin+pass=12345678+CMD=EnableXML
Once the XML is enabled you should see a message that says: EnableXML
Once XML has been enabled to access the XML type in the command: http://xxx.xxx.x.xxx/info.xml
The XML commands are listed below: http://xxx.xxx.x.xxx/info.xml
http://xxx.xxx.x.xxx/Set.cmd?user=admin+pass=12345678+CMD=EnableXML http://xxx.xxx.x.xxx/Set.cmd?user=admin+pass=12345678+CMD=DisableXML
Please view the XML output for reference.
- 37 –
Ref: DS9258Y90M02
11.) Frequently Asked Questions (F.A.Q)
Q1: How do I reset the device back to manufacturer default values?
Ans: In the front panel of the 9258 DS, there is a reset feature that will reset the device back to manufacturer default settings. Take a pen or small pin, then press and hold for about 10-15 seconds. Once you hear a single “beep” sound the device will be reset back to manufacturer default
Default IP: 192.168.1.100 (When 9258 DS is connected to PC directly)
Default Login: Admin
Default Password: 12345678
Q2:
What can I do if I forget my password?
Ans: In the login field enter the field
1.) “super user”: do not enter the quotation marks and there is a space between super and user.
2.) Then do not enter, a password and hit the submit button
3.) Unplug the device and plug it back in.
4.) Then use the default login and password
Default Login: admin
Default Password: 12345678
For security concern , please do power reboot 9258 in 1 minutes after click submit as type " super user " in the username as login
Q3: What is dual switch technology?
Ans: Dual Switch technology is an additional safety feature of the 9258 DS. Unlike conventional power distribution units or remote power control units the 9258 DS has a dual switch design which will completely cut off the power to the devices. Other designs which do not have this feature will may create a harmful environment that will affect the devices or the things around it. Below is a picture of
Q4: How come I cannot connect to my device from an outside network?
Ans: To use the device outside of LAN (Local Area Network. If a router is present you will have to port forward the Local IP Address of the 9258 DS so that it could be reached by the outside world. Please refer to the manual on how to accomplish this task.
- 38 –
Ref: DS9258Y90M02
Advertisement
Key Features
- Dual Switch Design
- Auto-ping (Watch dog)
- Supports: TCP/IP, Http API, Web Server
- Scheduler System
- 8 Power control output
- 1 RS232 port
- CNT Technology
- Supports UPNP
