Yamaha | YSP-1100 | Owner`s manual | Yamaha YSP-1100 Owner`s manual

YSP-1100_UAB-cv.fm Page 1 Friday, August 11, 2006 4:42 PM
UAB
YSP-1100
Digital Sound Projector
© 2006
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WH82880
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
■ Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert you to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
1
Read these instructions.
2
Keep these instructions.
3
Heed all warnings.
4
Follow all instructions.
5
Do not use this apparatus near water.
6
Clean only with dry cloth.
7
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10 Protect the power supply cable from being walked on or
pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
i En
IMPORTANT SAFETY INSTRUCTIONS
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by YAMAHA may
void your authority, granted by the FCC, to use the product.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
2. IMPORTANT:
When connecting this product to accessories and/or another
product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could
void your FCC authorization to use this product in the USA.
Relocate either this product or the device that is being
affected by the interference.
3. NOTE:
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements
provides a reasonable level of assurance that your use of
this product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the
operation of other electronic devices.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact YAMAHA Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by YAMAHA Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying
blaring or distortion – and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries
Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.
ii En
CAUTION: READ THIS BEFORE OPERATING THIS UNIT.
CAUTION: READ THIS BEFORE OPERATING THIS UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this sound system in a well ventilated, cool, dry, clean
place with at least 5 cm of space above (or below) this unit –
away from direct sunlight, heat sources, vibration, dust, moisture,
and/or cold.
Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes from cold
to hot, and do not locate this unit in an environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this
unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
Do not plug in this unit to a wall outlet until all connections are
complete.
Do not operate this unit upside-down. It may overheat, possibly
causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might damage
the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. YAMAHA will
not be held responsible for any damage resulting from use of this
unit with a voltage other than specified.
To prevent damage by lightning, keep the power cable
disconnected from a wall outlet or this unit during a lightning
storm.
Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed.
The cabinet should never be opened for any reasons.
When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
Before moving this unit, press STANDBY/ON to set this unit in
standby mode, and disconnect the AC power plug from the wall
outlet.
Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave the unit alone.
When using the unit for a long time, the unit may become warm.
Turn the power off, then leave the unit alone for cooling.
Install this unit near the AC outlet and where the AC power plug
can be reached easily.
The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
iii En
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
WARNING
THE POWER SUPPLY CABLE OF THIS UNIT MUST BE
CONNECTED TO THE MAIN SOCKET OUTLET VIA A
PROTECTIVE EARTHING CONNECTION.
This unit is not disconnected from the AC power source as long
as it is connected to the AC wall outlet, even if this unit itself is
turned off. This state is called the standby mode. In this state,
this unit is designed to consume a very small quantity of power.
IMPORTANT
Please record the serial number of this unit in the space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain this
Owner’s Manual in a safe place for future reference.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide
slot and fully insert.
This Class B digital apparatus complies with Canadian ICES003.
FOR U.K. CUSTOMERS
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below. Note that the plug severed from
the mains lead must be destroyed, as a plug with bared
flexible cord is hazardous if engaged in a live socket outlet.
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED. Make sure that neither core is connected to the
earth terminal of the three pin plug.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
01EN_YSP-1100_UAB_EN.book Page 1 Wednesday, August 30, 2006 1:46 PM
CONTENTS
OVERVIEW ........................................................... 2
FEATURES............................................................. 3
USING THIS MANUAL ........................................ 4
SUPPLIED ACCESSORIES ................................. 5
CONTROLS AND FUNCTIONS ......................... 6
PREPARATION
INSTALLATION ................................................. 11
Before installing this unit......................................... 11
Installing this unit .................................................... 11
CONNECTIONS .................................................. 15
GETTING STARTED.......................................... 24
USING SET MENU.............................................. 26
Displaying the OSD................................................. 26
The flow chart of SET MENU................................. 27
CHANGING OSD LANGUAGE ........................ 28
AUTO SETUP (IntelliBeam) ............................... 29
The flow chart of AUTO SETUP ............................ 29
Installing the optimizer microphone........................ 30
Using AUTO SETUP (IntelliBeam)........................ 31
Convenient usage of the system memory ................ 36
Saving settings ......................................................... 36
Loading settings....................................................... 37
What is a sound field? ............................................. 50
Sound field program descriptions............................ 51
Turning on CINEMA DSP programs ...................... 52
Turning off CINEMA DSP programs ..................... 54
Adjusting CINEMA DSP effect levels .................... 54
USING THE VOLUME MODE
(Night listening mode/TV volume
equal mode)........................................................55
USING BASS SOUND ENHANCER
(TruBass)............................................................57
USING THE SLEEP TIMER ..............................58
Setting the sleep timer ............................................. 58
Canceling the sleep timer ........................................ 59
ADVANCED OPERATION
MANUAL SETUP.................................................60
Using MANUAL SETUP ........................................ 61
BEAM MENU ......................................................... 62
SOUND MENU....................................................... 66
INPUT MENU......................................................... 68
DISPLAY MENU.................................................... 70
ADJUSTING THE AUDIO BALANCE .............72
Using the test tone ................................................... 72
Using the audio output being player back ............... 73
SELECTING THE INPUT MODE .....................75
ADJUSTING SYSTEM PARAMETERS ...........76
Using the system parameters ................................... 76
Setting the MEMORY PROTECT .......................... 76
Setting the MAX VOLUME.................................... 77
Setting the TURN ON VOLUME ........................... 78
Setting the DEMO MODE ...................................... 78
Setting the FACTORY PRESET ............................. 79
REMOTE CONTROL FEATURES ...................81
Setting remote control codes ................................... 81
Controlling other components ................................. 82
Using the TV macro ................................................ 84
ADDITIONAL INFORMATION
BASIC OPERATION
PLAYBACK.......................................................... 39
TROUBLESHOOTING .......................................86
GLOSSARY...........................................................89
Audio formats .......................................................... 89
Audio information ................................................... 89
INDEX ....................................................................90
SPECIFICATIONS...............................................91
ENJOYING SURROUND SOUND .................... 42
5 beam...................................................................... 42
LIST OF REMOTE CONTROL CODES ....................i
1 En
English
Selecting the input source........................................ 39
Playing back sources................................................ 40
Adjusting the volume............................................... 41
Muting the sound ..................................................... 41
ADDITIONAL
INFORMATION
USING THE SYSTEM MEMORY .................... 36
USING SOUND FIELD PROGRAMS................50
ADVANCED
OPERATION
Installing batteries in the remote control ................. 24
Operation range of the remote control..................... 24
Using the remote control ......................................... 25
Turning on the power............................................... 25
Using auto-adjust function....................................... 48
Using manual-adjust function.................................. 49
BASIC
OPERATION
SETUP
Stereo playback........................................................ 47
PLAYING BACK SOUND CLEARLY
(My beam) ..........................................................48
SETUP
Connecting a TV...................................................... 16
Connecting a DVD player/recorder ......................... 17
Connecting a VCR................................................... 18
Connecting a digital satellite tuner or
a cable TV tuner .................................................. 19
Connecting a digital airwave tuner .......................... 20
Connecting other external components ................... 21
Connecting a subwoofer .......................................... 22
Connecting the power supply cable......................... 23
About the RS-232C/REMOTE IN/IR-OUT
terminals .............................................................. 23
ENJOYING STEREO SOUND ...........................47
PREPARATION
Front panel ................................................................. 6
Front panel display .................................................... 7
Rear panel .................................................................. 8
Remote control........................................................... 9
Stereo plus 3 beam................................................... 43
3 beam...................................................................... 43
Enjoying 2-channel sources
in surround sound ................................................ 45
Adjusting surround mode parameters...................... 46
INTRODUCTION
INTRODUCTION
OVERVIEW
OVERVIEW
It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of
wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of
surround sound experience as your local movie theater.
YAMAHA YSP-1100 Digital Sound Projector challenges this preconception that complicated speaker setup and
troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.
This slimline unit does away with the need for complicated wiring and installation worries, leaving you with a unit that is
not only easy to set up, but which is also capable of reproducing the kind of powerful surround sound you have been
waiting for from its built-in 2 woofers and 40 full-range small speakers.
You can fine-tune the parameters of this unit to adjust the delay time for separate sound beams, resulting in highly
directional sound that comes in on the listening position from all directions.
The YSP-1100 projects sound beams containing surround sound information for the front right (R), front left (L),
surround right (SR) and surround left (SL) speaker positions, which are reflected off the walls of your listening room
before reaching the actual listening position. With the addition of center (C) sound beams, this Digital Sound Projector
creates true-to-life 5.1 channel surround sound that makes you feel as if there are actual speakers around the room.
Sit back and enjoy the real sound experience of this simple, yet stylish Digital Sound Projector.
Imaginary
front right
speaker
R
C
SR
L
SL
Imaginary
surround right
speaker
Imaginary
front left
speaker
Imaginary
center
speaker
Listening position
Imaginary
surround left
speaker
2 En
FEATURES
FEATURES
My beam
This unit employs the my beam so that you can achieve a
clear sound in noisy environment. You can adjust the
beam angle manually or automatically using the supplied
remote control.
Cinema DSP Digital
This unit employs the Cinema DSP Digital technology
developed by YAMAHA Electronics Corp. so that you can
experience movies at home with all the dramatic sound
impact that the director intended to convey.
Versatile Remote Control
The supplied remote control come with preset remote
control codes to be used to control the DVD player, VCR,
cable TV tuner and digital satellite tuner connected to this
unit. In addition, the remote control is equipped with the
macro capability so that you can perform a series of
operations with the press of a single button.
The “
” logo and “IntelliBeam” are trademarks of
YAMAHA Corporation.
The “
” logo and “Cinema DSP” are registered
trademarks of YAMAHA Corporation.
AUTO SETUP (IntelliBeam)
This unit employs the automatic sound beam and acoustic
optimization technology with the aid of the supplied
optimizer microphone so that you can avoid troublesome
listening-based speaker setup and achieve highly accurate
sound beam adjustments that best match your listening
environment.
INTRODUCTION
Digital Sound Projector
This unit employs the digital sound projector technology
that allows one slim unit to control and steer multiple
channels of sound to generate multi channel surround
sound, thus eliminating the need for satellite loudspeakers
and cabling normally associated with conventional
surround sound systems. This unit is also equipped with
the following beam modes so that you can enjoy the
surround sound.
◆ 5 beam
◆ Stereo plus 3 beam
◆ 3 beam
This unit also employs the stereo playback and my beam.
Compatibility with the Newest Technologies
This unit employs decoders compatible with Dolby
Digital, DTS (Digital Theater Systems), Dolby Pro Logic,
Dolby Pro Logic II and DTS Neo:6.
◆ Dolby Digital
This is the standard audio signal format used on DVDs and
other purely digital media. This surround technology deliver
high-quality digital audio for up to 5.1 discrete channels to
produce a directional and more realistic effect.
◆ DTS (Digital Theater Systems)
This is an audio signal format used on DVDs and other purely
digital media. This surround technology deliver high-quality
digital audio for up to 5.1 discrete channels to produce a
directional and more realistic effect.
◆ Dolby Pro Logic
This sophisticated, matrix decoding technology up-converts
any 2 channel source audio to a 5.1 channel full bandwidth
playback, resulting in a surround sound experience.
◆ Dolby Pro Logic II
This is fundamentally a redesigned version of Dolby Pro
Logic that employs 2 stereo surround channels, a subwoofer
and a greatly enhanced steering logic. As a result, this
improved technology provides an exceptionally stable sound
field that simulates 5.1 to a much greater degree than the
original Dolby Pro Logic. In addition, Dolby Pro Logic II
features Movie, Music and Game modes specifically designed
for movies, music and games respectively.
◆ DTS Neo:6
This technology decodes the conventional 2 channel sources
for 6 channel playback, enabling playback with the full-range
channels with higher separation. Music mode and Cinema
mode are available to play back music and movie sources
respectively.
“DTS” and “Neo:6” are trademarks of Digital Theater Systems,
Inc.
Manufactured under license from 1 Ltd. Worldwide patents
applied for.
The “
” logo and “Digital Sound Projector™” are trademarks
of 1 Ltd.
TruBass, SRS and the “
” symbol are registered trademarks
of SRS Labs, Inc. TruBass technology is incorporated under
license from SRS Labs, Inc.
3 En
English
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
USING THIS MANUAL
USING THIS MANUAL
Notes
• This manual describes how to connect and operate this unit. For details regarding the operation of external components, refer to the
supplied owner’s manual for the component.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In such cases, the operation is
described using remote control operation.
• y indicates a tip for your operation.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and product, the product has priority.
1
Install this unit in your listening room.
See “INSTALLATION” on page 11.
2
Connect this unit to your TV and other external components.
See “CONNECTIONS” on page 15.
3
Prepare the remote control and turn on the power of this unit.
See “GETTING STARTED” on page 24.
4
Run AUTO SETUP.
See “AUTO SETUP (IntelliBeam)” on page 29.
5
Play back a source.
See “PLAYBACK” on page 39.
6
Change the beam modes and/or CINEMA DSP settings.
See “ENJOYING SURROUND SOUND” on page 42.
If you want to make additional settings
and adjustments
7
Run MANUAL SETUP to fine-tune settings and/or set remote control codes.
See “MANUAL SETUP” on page 60 and “REMOTE CONTROL FEATURES” on page 81.
4 En
SUPPLIED ACCESSORIES
SUPPLIED ACCESSORIES
Remote control (×1)
Optical cable (×1)
POWER POWER
STANDBY/ON
AV
STB
Batteries (×2)
(AA, R6, UM-3)
INTRODUCTION
Check that you have received all of the following parts.
TV
VCR
DVD
AUX
INPUT1
TV
INPUT2
MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
OSD video pin cable (×1)
1
2
3
STEREO
MY BEAM
SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
(Yellow)
OFF
0
+10
CH LEVEL
Digital audio pin cable (×1)
3BEAM
(Orange)
MENU
TV/AV
Optimizer microphone (×1)
Audio pin cable (×1)
ENTER
YSP
RETURN
TEST
VOLUME
CH
MUTE
TV INPUT
TV VOL
(White/Red)
TV MUTE
CODE SET
Cable clamp (×1)
Cardboard microphone
stand (×1)
Fasteners (×4)
Power supply cable (×1)
English
5 En
01EN_YSP-1100_UAB_EN.book Page 6 Wednesday, August 30, 2006 1:46 PM
CONTROLS AND FUNCTIONS
CONTROLS AND FUNCTIONS
Front panel
1
2
INPUT
VOLUME
4
5
1 OPTIMIZER MIC jack
Use to connect the supplied optimizer microphone to be
used to run AUTO SETUP (see page 30).
2 Front panel display
Shows information about the operational status of this
unit.
3 Remote control sensor
Receives infrared signals from the remote control.
4 INPUT
Press repeatedly to switch between input sources (TV,
VCR, DVD or AUX). See page 39 for details.
Outputs a test tone to experience the sound beam (see
page 72).
5 VOLUME –/+
Controls the volume level of all audio channels (see
page 41).
6 En
3
+
STANDBY/ON
6
6 STANDBY/ON
Turns on the power of this unit or sets it to the standby
mode (see page 25).
Notes
• When you turn on the power of this unit, you will hear a click
and there will be a 4 to 5-second delay before it can reproduce
sound.
• In the standby mode, this unit consumes a small amount of
power in order to receive infrared-signals from the remote
control.
CONTROLS AND FUNCTIONS
Front panel display
2
NIGHT
SLEEP
3
PCM
INTRODUCTION
1
4
DIGITAL
PL
VOL
m
ft
mS
dB
5
1 NIGHT indicator
Lights up when one of the night listening modes is
selected (see page 55).
2 SLEEP indicator
Lights up when the sleep timer is turned on (see page 58).
3 Decoder indicators
Light up when the corresponding decoder of this unit is in
operation (see page 44).
4 Volume level indicator
Shows the current volume level (see page 41).
5 Multi-information display
Shows information when you adjust the parameters of this
unit.
y
You can adjust the brightness of the front panel display using the
DISPLAY MENU parameters in MANUAL SETUP (see
page 70).
English
7 En
CONTROLS AND FUNCTIONS
Rear panel
E
1
2
DVD
COAXIAL
RS-232C
REMOTE IN
3
4
AUX
TV/STB
OPTICAL
DIGITAL IN
5
TV/STB
6 7
VCR
AUDIO IN
1 RS-232C/REMOTE IN terminals
These are control expansion terminals for factory use only
(see page 23).
2 DVD COAXIAL DIGITAL IN jack
Use to connect a DVD player/recorder via a coaxial digital
connection (see page 17).
3 AUX OPTICAL DIGITAL IN jack
Use to connect an external component via an optical
digital connection (see page 21).
4 TV/STB OPTICAL DIGITAL IN jack
Use to connect a TV, a digital satellite tuner or a cable TV
tuner via an optical digital connection (see pages 16, 19
and 20).
5 TV/STB AUDIO IN jacks
Use to connect a TV, a digital satellite tuner or a cable TV
tuner via an analog audio connection (see pages 16, 19
and 20).
6 VCR AUDIO IN jacks
Use to connect a VCR via an analog audio connection
(see pages 17 and 18).
89
VCR
SUBWOOFER
COMPONENT
F
0
A
DVD/AUX
VIDEO IN
COMPONENT
B
C
D
COMPONENT
STB
VIDEO OUT
0 DVD/AUX COMPONENT VIDEO IN jacks
Use to connect a DVD player/recorder or an external
component via a component analog video connection
(see page 17).
A STB VIDEO IN jack
Use to connect a digital satellite tuner or a cable TV tuner
via a composite analog video connection (see pages 19
and 20).
B STB COMPONENT VIDEO IN jacks
Use to connect a digital satellite tuner or a cable TV tuner
via a component analog video connection (see pages 19
and 20).
C VIDEO OUT jack
Use to connect to the video input jack of your TV via a
composite analog video connection to display the OSD of
this unit (see page 16).
D COMPONENT VIDEO OUT jacks
Use to connect to the video input jacks of your TV via a
component analog video connection to display the OSD of
this unit (see page 16).
7 SUBWOOFER jack
Use to connect a subwoofer (see page 22).
E IR-OUT terminal
This is a control expansion terminal for factory use only
(see page 23).
8 VCR VIDEO IN jack
Use to connect a VCR via a composite analog video
connection (see page 18).
F AC IN
Use to connect the supplied power supply cable
(see page 23).
9 DVD/AUX VIDEO IN jack
Use to connect a DVD player/recorder or an external
component via a composite analog video connection
(see page 17).
8 En
CONTROLS AND FUNCTIONS
Remote control
y
You can also control other components using the remote control
once you set the appropriate remote control codes. See
“Controlling other components” on page 82 for details.
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 STANDBY/ON
Sets this system to the standby mode (see page 25).
3 Transmission indicator
Lights up when infrared control signals are being output.
INTRODUCTION
The functions of some buttons change depending on the
position of the operation mode selector (S). This section
basically describes the functions of the remote control
used to control this unit.
4 Input selector buttons
Use to select an input source (STB, VCR, DVD, AUX or TV).
Use to change the control area of the remote control. (S:TV/AV)
POWER POWER
STANDBY/ON
STB
VCR
INPUT1
AV
TV
DVD
AUX
6 AUTO SETUP
Use to enter the AUTO SETUP menu (see page 29).
TV
INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
0
7 Numeric buttons
Use to enter numbers. (S:TV/AV)
8 STEREO
Use the playback sources in 2-channel stereo (see
page 47).
9 Sound field program buttons
Use to select sound field programs (see page 50).
OFF
+10
CH LEVEL
5 VOL MODE
Turns on or off the volume modes (see page 55).
MENU
0 CH LEVEL
Adjusts the volume level of each channel (see page 73).
TV/AV
ENTER
YSP
RETURN
TEST
VOLUME
MUTE
CH
TV INPUT
TV VOL
TV MUTE
CODE SET
A Cursor buttons
/
/ / , ENTER
Use to select and adjust SET MENU items.
Use to select DVD menu items. (S:TV/AV)
B TEST
Outputs a test tone when adjusting the output level of each
speaker (see page 72).
C VOLUME +/–
Increases or decreases the volume level of this unit (see
page 41).
D MUTE
Mutes the sound. Press again to restore the audio output to
the previous volume level (see page 41).
E TV INPUT
Switches the input source or the TV (see page 82).
F DVD player/VCR control buttons
Use to control the DVD player or the VCR (see pages 82
and 83).
9 En
English
G My beam microphone
Use to collect the test tones from this unit when using the
my beam auto-adjust function (see page 48).
CONTROLS AND FUNCTIONS
H TV POWER
Turns on the power of the TV or sets it to the standby
mode (see page 82).
I AV POWER
Turns on the power of the selected component or sets it to
the standby mode (see pages 82 and 83).
J INPUT1/INPUT2
Selects the input source of the TV (see page 82).
K MACRO
Use to set the TV macro (see page 84).
L SLEEP
Sets the sleep timer (see page 58).
M INPUTMODE
Switches between input modes (AUTO, DTS or
ANALOG). See page 75 for details.
N Beam mode buttons
Change the beam mode settings (see pages 42, 47 and 48).
O SURROUND
Selects the surround mode for playback (see page 42).
P MY BEAM
Use to select the my beam as the beam mode (see
page 48).
Q
TruBass
Use to effectively reproduce the bass sound (see page 57).
R MENU
Displays the setup menu on your TV monitor (see
pages 31 and 61).
Display the DVD menu. (S:TV/AV)
S Operation mode selector
Selects the operation mode of this unit. Select YSP when
operating this unit and select TV/AV when operating the
TV or other AV components set up the appropriate remote
control codes.
T RETURN
Use to select sleep timer settings or return to the previous
SET MENU screen.
Use to return to the previous DVD menu screen or exit the
DVD menu. (S:TV/AV)
U TV VOL +/–
Adjusts the volume level of the TV (see page 82).
V CH +/–
Switches between channels of the TV or the VCR (see
pages 82 and 83).
W TV MUTE, CODE SET
Mutes the audio output of the TV (see page 82).
Use to set up remote control codes (see page 81).
10 En
INSTALLATION
INSTALLATION
This section describes a suitable installation location to install the unit using a metal wall bracket, a rack or a stand.
Before installing this unit
Installing this unit
Install this unit where there are no obstacles such as
furniture obstructing the path of sound beams. Otherwise,
the desired surround sound effects may not be achieved.
You may install this unit in parallel with the wall or in the
corner.
Parallel installation
Install this unit in the exact center of the wall when it is
measured from the left and right corners.
PREPARATION
This unit creates surround sound by reflecting projected
sound beams off the walls of your listening room. The
surround sound effects produced by this unit may not be
sufficient when the unit is installed in the following
locations.
• Rooms with surfaces inadequate for reflecting sound
beams
• Rooms with acoustically absorbent surfaces
• Rooms with measurements outside the following range
W (3 to 7 m) x H (2 to 3.5 m) x D (3 to 7 m)
• Rooms with less than 1.8 m from the listening position
to the speaker positions
• Rooms where objects such as furniture are likely to
obstruct the path of sound beams
• Rooms where the listening position is close to the walls
• Rooms where the listening position is not in front of
this unit
Make sure you leave an adequate amount of ventilation
space so that heat can escape. Make at least 5 cm of space
above or below this unit.
An object, such as furniture
Side view
Corner installation
Install this unit in the corner at a 40º to 50º angle from the
adjacent walls.
5 cm or more
40° to 50°
Front
Rear
Side
Notes
An object, such as furniture
English
• We do not recommend installing this unit so that it is positioned
directly on the floor of your listening room. Please install this
unit using a metal wall bracket, rack or stand.
• This unit weighs 9.0 kg. Be sure to install this unit where it will
not fall subject to vibrations, such as from an earthquake, and
where it is out of the reach of children.
• When using a cathode-ray tube (CRT) TV, do not install this
unit directly above your TV.
• This unit is shielded against magnetic rays. However, if the
picture on your TV screen becomes blurred or distorted, we
recommend moving the speakers away from your TV.
11 En
INSTALLATION
■ Installation examples
Example 1
Install this unit as close to the exact center of the wall as possible.
Example 2
Install this unit so that the sound beams can be reflected off the walls.
Example 3
Install this unit as close to the exact front of your normal listening position.
12 En
INSTALLATION
■ Using a metal wall bracket
■ Using a TV stand
You can use the optional metal wall bracket to mount this
unit on the wall in your listening room.
You can use the optional TV stand to install this unit. For
detailed information on installing this unit using a TV
stand, refer to the installation manual supplied with the
optional TV stand.
Metal wall bracket
TV
This unit
PREPARATION
TV
y
Refer to the instructions supplied with the metal bracket for
details on how to attach the metal bracket to the wall or how to
attach this unit to the metal bracket.
■ Using a stand
You can mount your TV on the stand placed on a
commercially available rack to install this unit under your
TV.
Stand
This unit
■ Using a rack
You can install this unit either above or under your TV in a
commercially available rack.
TV
When this unit is installed above your TV
This unit
y
Refer to the instructions supplied with the stand for details on
how to install the stand or how to mount this unit and the TV on
the stand.
When this unit is installed under your TV
Note
Make sure that the rack is large enough to allow adequate
ventilation space around this unit (see page 11) and that it is
strong enough to support the weight of both this unit and your TV.
English
13 En
INSTALLATION
■ Affixing this unit
Peel off the film from each of the four supplied fasteners
and then secure them to the bottom four corners of this
unit and the top of the rack, etc.
This unit
Peel off
the pad
on the
bottom
Peel off
the film 2
Fasteners
1
Notes
• Do not install this unit on top of a slanted surface. This unit may
fall over and cause injury.
• Make sure you wipe the surface of the rack, etc. before securing
the fasteners. Applying the tape to a dirty or wet surface will
weaken the sticking power of the tape, and this unit may fall as
a result.
14 En
CONNECTIONS
CONNECTIONS
This unit is equipped with the following types of audio/video input/output jacks:
For audio input
• 2 optical digital input jacks
• 1 coaxial digital input jack
• 2 sets of analog input jacks
For video input
• 3 composite analog input jacks
• 2 sets of component analog input jacks
For video output
• 1 composite analog output jack
• 1 set of component analog output jacks
CAUTION
Do not connect this unit or other components to the main power until all connections between components are complete.
PREPARATION
Use these audio/video input/output jacks to connect external components such as your TV, DVD player, VCR, digital
satellite tuner, cable TV tuner and game console. Further, by connecting a subwoofer to this unit, you can enjoy
reinforced low bass sounds. For details on how to connect various types of external components to this unit, see pages 16
to 22.
Audio connection
Video connection
TV
This unit
DVD player
Subwoofer
VCR
Optical fiber cable
English
To prevent cables from becoming unplugged, place the supplied
cable clamp with the open side facing upward, attach it to the rear
panel of this unit in a suitable position and then affix cables in the
cable clamp.
Digital satellite tuner, cable TV
tuner or game console
Attach to this unit
15 En
CONNECTIONS
Connecting a TV
Connect a TV to this unit and display the OSD for easy viewing when you adjust the system parameters in SET MENU.
■ Audio connections
■ Video connections
Connect the analog audio output jacks of your TV to the
TV/STB AUDIO IN jacks of this unit. If your TV has an
optical digital output jack, connect the optical digital
output jack of your TV to the TV/STB OPTICAL
DIGITAL IN jack of this unit in addition to the analog
audio connection. Once the digital audio connection is
made, digital audio signals can be input to this unit during
digital broadcasting.
Connect the video input jacks of your TV to the VIDEO
OUT jacks of this unit. If your TV has component video
input jacks, connect the component video input jacks of
your TV to the COMPONENT VIDEO OUT jacks of this
unit in addition to the composite video connection. Once
the component video connection is made, you can enjoy
images with better resolution.
y
• The circuits of composite and component video signals are independent of each other.
• To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 15).
Note
If you connect this unit to the analog audio and optical digital audio output jacks at the same time as shown in the left illustration below,
the digital audio signals output at the optical digital output jack take priority over the analog audio signals output at the analog audio
output jacks.
TV
Optical digital
output
Analog audio
output
R
Video
input
Component
video input
L
Remove the caps if
attached
Check the direction
Rear panel of this unit
COMPONENT
DVD
COAXIAL
RS-232C
REMOTE IN
TV/STB
AUX
OPTICAL
DIGITAL IN
TV/STB
VCR
AUDIO IN
Cables used for audio connections
VCR
SUBWOOFER
COMPONENT
STB
VIDEO OUT
Cables used for video connections
Audio pin cable (supplied)
(White)
DVD/AUX
VIDEO IN
COMPONENT
Video pin cable (supplied)
(White)
(Yellow)
(Yellow)
(Red)
(Red)
Component video pin cable
Optical cable (supplied)
16 En
(Green)
(Green)
(Blue)
(Blue)
(Red)
(Red)
01EN_YSP-1100_UAB_EN.book Page 17 Wednesday, August 30, 2006 1:46 PM
CONNECTIONS
Connecting a DVD player/recorder
Connect a DVD player/recorder and enjoy DVDs.
■ Video connections
Connect the optical digital output jack of your DVD
player/recorder to the DVD COAXIAL DIGITAL IN jack
of this unit. In case you connect this unit to a DVD/VCR
combo player/recorder, connect the analog audio output
jacks of your DVD/VCR combo player/recorder to the
VCR AUDIO IN jacks of this unit in addition to the
optical digital audio connection.
Connect the video output jack of your DVD player/
recorder to the DVD/AUX VIDEO IN jack of this unit. If
your DVD player/recorder has component video output
jacks, connect the component video output jacks of your
DVD player/recorder to the DVD/AUX COMPONENT
VIDEO IN jacks of this unit. Once the component video
connection is made, you can enjoy images with better
resolution.
y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 15).
Notes
PREPARATION
■ Audio connections
• Check that your DVD player/recorder is properly set to output Dolby Digital and DTS digital audio signals. If not, adjust the system
settings of your DVD player/recorder. For details, refer to the operation manual supplied with your DVD player/recorder.
• If your DVD player/recorder does not have a coaxial digital output jack, make an optical digital audio connection instead
(see page 21).
DVD player/recorder
Coaxial digital Analog audio
output
output
R
Video
output
Component
video input
L
Note
*
In case you connect this
unit to a DVD/VCR
combo player/recorder
*
Note
You can only make either a
composite or a component
video connection.
Rear panel of this unit
COMPONENT
DVD
COAXIAL
RS-232C
REMOTE IN
AUX
TV/STB
OPTICAL
TV/STB
DIGITAL IN
VCR
AUDIO IN
Cables used for audio connections
VCR
SUBWOOFER
COMPONENT
STB
VIDEO OUT
Cables used for video connections
Audio pin cable
(White)
DVD/AUX
VIDEO IN
COMPONENT
Video pin cable
(White)
(Yellow)
(Yellow)
(Red)
(Red)
Component video pin cable
Digital audio pin cable (supplied)
(Orange)
(Orange)
(Green)
(Blue)
(Blue)
(Red)
(Red)
17 En
English
(Green)
CONNECTIONS
Connecting a VCR
Connect a VCR and enjoy video cassette tapes.
■ Audio connections
■ Video connections
Connect the analog audio output jacks of your VCR to the
VCR AUDIO IN jacks of this unit.
Connect the video output jack of your VCR to the VCR
VIDEO IN jack of this unit.
Note
Be sure to match the left and right output jacks of your VCR with the left and right input jacks of this unit.
VCR
Analog audio
output
R
Video
output
L
Rear panel of this unit
COMPONENT
TV/STB
AUX
OPTICAL
DVD
COAXIAL
RS-232C
REMOTE IN
DIGITAL IN
TV/STB
VCR
AUDIO IN
Cables used for audio connections
VCR
SUBWOOFER
18 En
STB
VIDEO OUT
Video pin cable
(White)
(Yellow)
(Red)
DVD/AUX
VIDEO IN
COMPONENT
Cables used for video connections
Audio pin cable
(White)
COMPONENT
(Red)
(Yellow)
01EN_YSP-1100_UAB_EN.book Page 19 Wednesday, August 30, 2006 1:46 PM
CONNECTIONS
Connecting a digital satellite tuner or a cable TV tuner
Connect a digital satellite tuner or a cable TV tuner and enjoy digital satellite broadcasting or cable TV broadcasting.
■ Video connections
Connect the optical digital output jack of your digital
satellite tuner or cable TV tuner to the TV/STB OPTICAL
DIGITAL IN jack of this unit. Connect the analog audio
output jacks of your digital satellite tuner or cable TV
tuner to the TV/STB AUDIO IN jacks of this unit in
addition to the optical digital audio connection.
Connect the video output jack of your digital satellite
tuner or cable TV tuner to the STB VIDEO IN jack of this
unit. If your digital satellite tuner or cable TV tuner has
component video output jacks, connect the component
video output jacks of your digital satellite tuner or cable
TV tuner to the STB COMPONENT VIDEO IN jacks of
this unit. Once the component video connection is made,
you can enjoy images with better resolution.
y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 15).
Digital satellite tuner
or a cable TV tuner
Optical digital
output
Analog audio
output
R
Video
output
PREPARATION
■ Audio connections
Component
video output
L
Note
You can only
make either a
composite or a
component video
connection.
Rear panel of this unit
COMPONENT
TV/STB
AUX
OPTICAL
DVD
COAXIAL
RS-232C
REMOTE IN
DIGITAL IN
TV/STB
VCR
AUDIO IN
Cables used for audio connections
VCR
SUBWOOFER
DVD/AUX
VIDEO IN
COMPONENT
STB
VIDEO OUT
Cables used for video connections
Audio pin cable
(White)
COMPONENT
Video pin cable
(White)
(Yellow)
(Yellow)
(Red)
(Red)
Component video pin cable
Optical cable
(Green)
(Green)
(Blue)
(Blue)
(Red)
(Red)
English
19 En
01EN_YSP-1100_UAB_EN.book Page 20 Wednesday, August 30, 2006 1:46 PM
CONNECTIONS
Connecting a digital airwave tuner
If your digital airwave tuner does not support analog broadcasting, make audio/video connections as shown below.
■ Audio connections
■ Video connections
Connect the optical digital output jack of your digital
airwave tuner to the TV/STB OPTICAL DIGITAL IN jack
of this unit. Connect the TV/STB AUDIO IN jacks of this
unit to the analog audio output jacks of your TV in
addition to the optical digital audio connection between
your digital airwave tuner and this unit.
Connect the video output jack of your digital airwave
tuner to the STB VIDEO IN jack of this unit. If your
digital airwave tuner has component video output jacks,
connect the component video output jacks of your digital
airwave tuner to the STB COMPONENT VIDEO IN jacks
of this unit. Once the component video connection is
made, you can enjoy images with better resolution.
y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 15).
Digital airwave tuner
Optical digital
output
Video
output
Component
video output
Connect to the analog
audio output jacks of
the TV.
Note
You can only
make either a
composite or a
component video
connection.
Rear panel of this unit
COMPONENT
AUX
TV/STB
OPTICAL
DVD
COAXIAL
RS-232C
REMOTE IN
DIGITAL IN
TV/STB
VCR
AUDIO IN
Cables used for audio connections
VCR
SUBWOOFER
DVD/AUX
VIDEO IN
COMPONENT
STB
VIDEO OUT
Cables used for video connections
Audio pin cable
(White)
COMPONENT
Video pin cable
(White)
(Yellow)
(Yellow)
(Red)
(Red)
Component video pin cable
Optical cable
20 En
(Green)
(Green)
(Blue)
(Blue)
(Red)
(Red)
01EN_YSP-1100_UAB_EN.book Page 21 Wednesday, August 30, 2006 1:46 PM
CONNECTIONS
Connecting other external components
To connect other external components, connect the optical digital output jack of an external component to the AUX
OPTICAL DIGITAL IN jack of this unit. Use this connection method to connect an external component that supports an
optical digital connection or to connect a DVD player/recorder via an optical digital connection.
y
To prevent the optical cable from being unplugged, affix the optical cable in the supplied cable clamp (see page 15).
Note
If you connect a DVD player/recorder via a coaxial digital connection, adjust settings for INPUT ASSIGNMENT (see page 68).
PREPARATION
CD player, etc.
Optical digital
output
Rear panel of this unit
COMPONENT
DVD
COAXIAL
RS-232C
REMOTE IN
AUX
TV/STB
OPTICAL
DIGITAL IN
TV/STB
VCR
AUDIO IN
VCR
SUBWOOFER
DVD/AUX
VIDEO IN
COMPONENT
COMPONENT
STB
VIDEO OUT
Cables used for connections
Optical cable
English
21 En
CONNECTIONS
Connecting a subwoofer
To connect a subwoofer, connect the monaural input jack of your subwoofer to the SUBWOOFER jack of this unit.
If a subwoofer is connected to this unit, turn on the power of your subwoofer and then run AUTO SETUP (see page 29)
or select SWFR for BASS OUT in SUBWOOFER SET (see page 67).
Subwoofer
Monaural
input
Rear panel of this unit
COMPONENT
DVD
COAXIAL
RS-232C
REMOTE IN
AUX
TV/STB
OPTICAL
DIGITAL IN
TV/STB
VCR
AUDIO IN
VCR
SUBWOOFER
DVD/AUX
VIDEO IN
Cables used for connections
Subwoofer pin cable
22 En
COMPONENT
COMPONENT
STB
VIDEO OUT
CONNECTIONS
Connecting the power supply cable
Once all other connections are complete, plug one end of the power supply cable into the AC IN terminal of this unit and
then plug the other end into the AC wall outlet.
To the AC outlet
PREPARATION
About the RS-232C/REMOTE IN/IR-OUT terminals
The RS-232C, REMOTE IN and IR-OUT terminals do not support normal external component connections. These are
control expansion terminals for factory use only.
RS-232C terminal
REMOTE IN terminal
AUX
COAXIAL
RS-232C
REMOTE IN
DVD
TV/STB
OPTICAL
DIGITAL INPUT
IR-OUT terminal
TV/STB
AUDIO
English
23 En
GETTING STARTED
GETTING STARTED
Installing batteries in the remote
control
y
Remove the transparent sheet before using the remote control.
Press
Operation range of the remote
control
1
Press and hold the
mark on the battery
cover and then slide off the cover.
2
Insert the two supplied batteries (AA, R6,
UM-3) into the battery compartment.
Make sure you insert the batteries according to the
polarity markings (+/–).
3
The remote control transmits a directional infrared beam.
Use the remote control within 6 m of this unit and point it
toward the remote control sensor on this unit during
operation.
Approximately
6m
Close the battery cover.
Notes
• Change all of the batteries if you notice the following
conditions; the operation range of the remote control decreases,
the indicator does not blink or its light becomes dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• Exhausted batteries may leak. If the batteries have leaked,
dispose of them immediately. Avoid touching the leaked
material or letting it come into contact with clothing, etc. Clean
the battery compartment thoroughly before installing new
batteries.
• Do not throw away batteries with general house waste. Dispose
of them correctly in accordance with your local regulations.
• The contents of the memory stored in the remote control may be
erased in the following cases:
– The remote control is left without batteries for more than 2
minutes.
– Exhausted batteries remain in the remote control.
– The buttons on the remote control are accidentally pressed
when you change batteries.
• If the memory stored in the remote control is unwantedly
erased, insert new batteries and reset the remote control codes
again.
24 En
Notes
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types
of conditions:
– places of high humidity, such as near a bath
– places of high temperatures, such as near a heater or a stove
– places of extremely low temperatures
– dusty places
• Do not expose the remote control sensor on this unit to direct
sunlight or lighting such as inverted fluorescent lamps.
• If the batteries grow old, the effective operation distance of the
remote control decreases considerably. If this happens, replace
the batteries with two new ones as soon as possible.
GETTING STARTED
Using the remote control
Turning on the power
This section describes how to control this unit using the
supplied remote control. The functions of the remote
control change depending on the position of the operation
mode selector. Set the operation mode selector to YSP to
switch to the operation mode of this unit. The buttons on
the remote control numbered 1 to 4 are operational only
when you select YSP. Also, functions of the buttons
numbered 5 to 9 vary depending on the position of the
operation mode selector. The corresponding functions of
the buttons, see page 9.
INPUT
y
VOLUME
+
You can control other components by setting the appropriate
remote control codes (see page 81). Once the remote control code
for each input source (DVD, VCR, STB, TV or AUX) is set, see
“Controlling other components” on page 82 for further
information on the specific functions of the available remote
control buttons for each input source.
STANDBY/ON
POWER POWER
STANDBY/ON
Operational buttons only when YSP is
selected
STB
VCR
TV
DVD
AUX
TV
INPUT2 MACRO
SETUP
INPUT1
AV
TV
STB
VCR
DVD
AUX
TV
INPUT2 MACRO
INPUT1
TV
1
5BEAM
ST+3BEAM
3BEAM
2
3
1
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
OFF
CH LEVEL
Press STANDBY/ON on the front panel or on
the remote control to turn on the power of
this unit.
The volume level appears in the front panel display
and then the input source and beam mode currently
selected are displayed.
4
+10
0
2
1
AUTO
VOL MODE SETUP INPUTMODE SLEEP
STANDBY/ON
MENU
or
TV/AV
ENTER
YSP
3
Front panel
RETURN
TEST
VOLUME
TV VOL
CH
2
Function-varying buttons
5
STB
VCR
DVD
INPUT1
Remote control
Press STANDBY/ON on the front panel or on
the remote control again to set this unit to
the standby mode.
AUX
TV
INPUT2 MACRO
Note
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
1
6
STEREO
ST+3BEAM
3BEAM
2
3
When the unit is in the standby mode, only STANDBY/ON on the
front panel or on the remote control is operational, and the other
control buttons on the front panel or on the remote control are not
operational until the power of this unit is turned on.
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
OFF
0
+10
CH LEVEL
8
English
7
MENU
TV/AV
ENTER
YSP
RETURN
TEST
VOLUME
CH
9
TV VOL
25 En
USING SET MENU
USING SET MENU
Displaying the OSD
This section simply describes how to display the OSD (on-screen display) of this unit on your TV screen and set the
parameters for your listening room. Once this is complete, you can enjoy real surround sound while watching TV in the
comfort of your own home.
Note
The OSD is not output at the COMPONENT VIDEO OUT jacks of this unit. Connect the VIDEO OUT jack of this unit to the video
input jacks of your TV to display the OSD.
5
POWER POWER
STANDBY/ON
STB
VCR
INPUT1
AV
TV
DVD
AUX
TV
INPUT2 MACRO
TV
Press TV on the remote control to display the
OSD of this unit on your TV screen.
It may take a few seconds before this unit’s OSD
appears on your TV screen.
If the OSD does not appear, use the remote control
provided with your TV to switch the video input until
the OSD appears.
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
TV
TV
AUTO:ANALOG
OFF
0
+10
OSD screen example
CH LEVEL
MENU
TV/AV
ENTER
YSP
RETURN
TEST
1
Check that the video input jack on your TV is
connected to the VIDEO OUT jacks of this
unit to display the OSD of this unit.
2
Press STANDBY/ON on the front panel or on
the remote control to turn on the power of
this unit.
STANDBY/ON
or
Front panel
Remote control
3
Turn on the power of your TV.
4
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
YSP
26 En
USING SET MENU
The flow chart of SET MENU
The following diagram illustrates the overall flow of the setup procedure.
Run LANGUAGE SETUP.
See “CHANGING OSD LANGUAGE” on page 28.
Run AUTO SETUP (IntelliBeam).
See “AUTO SETUP (IntelliBeam)” on page 29.
If an error occurs
SETUP
Look for a remedy.
See “Error messages for AUTO SETUP” on page 35 for a complete list of error
messages and possible remedies.
Play back audio signals or adjust the settings for the beam mode and the CINEMA DSP.
See “PLAYBACK” on page 39.
If you want to make additional settings
and adjustments
Run MANUAL SETUP.
See “MANUAL SETUP” on page 60.
y
• If you cannot clearly hear a sound beam from a specific channel, adjust settings for
SETTING PARAMETERS (see page 62) or for BEAM ADJUSTMENT (see page 63) in
BEAM MENU.
• If there are acoustically absorbent objects such as curtains in the path of the sound beams,
adjust settings for TREBLE GAIN in BEAM MENU (see page 65).
English
27 En
CHANGING OSD LANGUAGE
CHANGING OSD LANGUAGE
This feature allows you to select the language of your choice that appears in the SET MENU of this unit.
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
4
Press
/
to select the language and
then press ENTER.
TV/AV
YSP
ENTER
2
Press MENU on the remote control.
The SET MENU screen appears on your TV.
SET MENU
MENU
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
y
• The control buttons used for SET MENU are displayed on
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN on the remote control.
• To cancel the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
3
ENTER
Press
/
to select LANGUAGE SETUP
and then press ENTER.
The following screen appears on your TV.
ENTER
ENTER
LANGUAGE SETUP
28 En
p
p
. ENGLISH
DEUTSCH
Francais
ESPANOL
[ ]/[ ]:Select
[ENTER]:Return
Choices: ENGLISH (English), DEUTSCH (German),
Français (French), ESPAÑOL (Spanish)
AUTO SETUP (INTELLIBEAM)
AUTO SETUP (IntelliBeam)
This unit creates a sound field by reflecting sound beams on the walls of your listening room and broadening the
cohesion of all the channels. Just as you would arrange the speaker position of other audio systems, you need to set the
beam angle to enjoy the best possible sound from this unit.
This unit employs the beam optimization and sound optimization features with the aid of the supplied optimizer
microphone, allowing you to avoid troublesome listening-based setup and achieving highly accurate sound adjustments
that best match your listening environment. We call these 2 features “IntelliBeam” generically.
The beam optimization creates the best possible surround sound field without manually setting the parameters for your
listening room.
The sound optimization feature performs the following checks and automatically makes appropriate sound adjustments.
DISTANCE:
Checks the distance of each beam from this unit and adjusts the delay of each channel so that each sound beam reaches
the listening position at the same time.
EQUALIZING:
Adjusts frequency and levels of each channel’s parametric equalizer to reduce coloration across the channels and create a
cohesive sound field. The sound optimization feature incorporates three parameters (frequency, level and Q factor) for
each of the seven bands in its parametric equalizer to provide highly precise automatic adjustment of frequency
characteristics.
SETUP
LEVEL:
Checks and adjusts the sound output level of each channel.
The flow chart of AUTO SETUP
This unit performs a series of checks to optimize the beam angle, delay, volume and quality. You can choose to optimize
all or part of the parameters.
Notes
Checking the environment of
your listening room
*1
Optimizing the beam angle
Beam
optimization
*1 The beam angle checking procedure is skipped if SOUND
OPTIMZ only is selected.
*2 The sound optimization procedure is skipped if BEAM
OPTIMZ only is selected.
*3 The subwoofer checking procedure is skipped if BEAM
OPTIMZ only is selected.
*2 *3
Checking the subwoofer
Optimizing the beam delay,
frequency and volume
Sound
optimization
English
29 En
AUTO SETUP (IntelliBeam)
Installing the optimizer microphone
The supplied optimizer microphone collects and analyzes the sound that this unit produces in your actual listening
environment. Follow the procedure below to connect the optimizer microphone to this unit and make sure that the
optimizer microphone is placed in a proper location and that there are no large obstacles between the optimizer
microphone and the walls in your listening room.
Notes
• After you have completed the AUTO SETUP procedure, be sure to disconnect the optimizer microphone.
• The optimizer microphone is sensitive to heat.
– Keep it away from direct sunlight.
– Do not place it on top of this unit.
• Do not connect the optimizer microphone to an extension cable as doing so may result in an inaccurate sound optimization.
• An error may occur during the AUTO SETUP procedure if the optimizer microphone is not properly placed in your listening room. To
avoid the possibility of an error:
– Do not place the optimizer microphone to the extreme right or left from the center of this unit.
– Do not place the optimizer microphone within 1.8 m (6.0 ft) from the front of this unit.
– Do not place the optimizer microphone more than 1 m (3.3 ft) upper or lower from the center height of this unit.
• Make sure that there are no obstacles between the optimizer microphone and the walls in your listening room as these objects obstruct
the path of sound beams. However, any objects that are in contact with the walls will be regarded as a protruding part of the walls.
• The best possible results are achieved if the optimizer microphone is placed at the same height as your ears would be when you are
seated in your listening position. However, if this is not possible, you can manually fine-tune the sound beam angle and balance the
sound beam output levels using MANUAL SETUP (see page 60) once the AUTO SETUP procedure is completed.
• If a subwoofer with adjustable volume and crossover/high cut frequency controls is connected to this unit, set the volume between 11
and 1 o’clock as viewed on a conventional clockface and set the crossover/high cut frequency to the maximum.
CROSSOVER
HIGH CUT
VOLUME
MIN
MAX
MIN
MAX
Subwoofer
1
Press STANDBY/ON on the front panel or on
the remote control to turn off the power of
this unit.
STANDBY/ON
or
Front panel
2
Remote control
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the side of this
unit.
Side view
3
Place the optimizer microphone on a flat
level surface more than 1.8 m (6.0 ft) from the
front of the unit and within 1 m (3.3 ft) upper
or lower from the center height of the unit
with the optimizer microphone head upward
at your normal listening position.
Note
Be sure to place the optimizer microphone on an imaginary
center line drawn from this unit.
y
You may want to use the supplied cardboard microphone stand
to affix the optimizer microphone at the same height as your
ears would be when you are seated in your listening position.
Optimizer
microphone
Within 1 m (3.3 ft)
upper or lower
from the center
More than
1.8 m (6.0 ft)
Optimizer microphone
30 En
Cardboard
microphone stand
Sofa
AUTO SETUP (IntelliBeam)
Using AUTO SETUP (IntelliBeam)
Once the optimizer microphone is firmly connected to this
unit and properly placed in your listening room, follow the
procedure below to start the AUTO SETUP procedure.
You can also enter the AUTO SETUP procedure simply by
pressing and holding AUTO SETUP on the remote control
more than 2 seconds. In this case, this unit performs both
of the beam optimization and sound optimization
procedures.
Center line
Optimizer
microphone
■ Assembling the supplied cardboard
microphone stand
You will find three separate parts (one circular-shaped part
and two longitudinal-shaped parts) of the cardboard
microphone stand originally put together.
+
VOLUME
STANDBY/ON
SETUP
1
INPUT
2
POWER POWER
STANDBY/ON
STB
VCR
INPUT1
AV
TV
DVD
AUX
TV
INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
3
4
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
OFF
0
+10
CH LEVEL
MENU
TV/AV
ENTER
Disassemble the three parts of the cardboard
microphone stand originally put together.
2
Insert one of the longitudinal-shaped part
into the crevice of the other longitudinalshaped part.
3
Place the circular-shaped part on top of the
two combined longitudinal-shaped parts.
4
Place the supplied optimizer microphone on
top of the circular-shaped part.
YSP
TEST
RETURN
English
1
31 En
AUTO SETUP (IntelliBeam)
3
Notes
• Make sure that your listening room is as quiet as possible while
this unit is performing the AUTO SETUP procedure.
• To achieve the best results possible, evacuate yourself from
your listening room until the AUTO SETUP procedure is
completed so that you may not obstruct the path of sound
beams.
• Be advised that it is normal for loud test tones to be output
during the AUTO SETUP procedure.
• The AUTO SETUP procedure may not be run successfully if
this unit is installed in one of the rooms described in “Before
installing this unit” on page 11. In such cases, run MANUAL
SETUP (see page 60) to manually adjust the corresponding
parameters.
• If an error occurs, an error buzzer is played, the AUTO SETUP
procedure stops and then an error message appears on the
screen. See “Error messages for AUTO SETUP” on page 35 for
appropriate remedies.
SET MENU
MENU
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
y
• The control buttons used for SET MENU are displayed on
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN on the remote control.
• To cancel the SET MENU screen, press MENU again.
• You can start the BEAM+SOUND OPTIMZ procedure
simply by pressing and holding AUTO SETUP on the
remote control for more than 2 seconds. Step 4 and 5 are
skipped and then the screen shown in step 5 is displayed
on your TV. Start the AUTO SETUP procedure from
step 6.
• You can also perform the following operations in the front
panel display.
y
• The AUTO SETUP procedure takes about 3 minutes maximum.
A chime is played when the AUTO SETUP procedure is run
successfully.
• If there are curtains in your listening room, we recommend
following the procedure below.
1. Open the curtains to improve sound reflection.
2. Run BEAM OPTIMZ only.
3. Close the curtains.
4. Run SOUND OPTIMZ only.
• You can save the settings optimized by the AUTO SETUP
procedure (see page 36). A set of settings optimized according
to specific conditions of your listening environment can be
recalled later depending on the varying conditions of your
listening environment (see page 37).
Press MENU on the remote control.
The SET MENU screen appears on your TV.
4
Press
/
on the remote control to select
AUTO SETUP and then press ENTER.
The following screen appears on your TV.
ENTER
1
ENTER
Press STANDBY/ON on the front panel or on
the remote control to turn on the power of
this unit.
If a subwoofer is connected to this unit, turn on the
power of the subwoofer.
STANDBY/ON
;AUTO SETUP
or
. 1)BEAM+SOUND OPTIMZ
2)BEAM OPTIMZ only
3)SOUND OPTIMZ only
Front panel
Remote control
2
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
YSP
32 En
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
01EN_YSP-1100_UAB_EN.book Page 33 Wednesday, August 30, 2006 1:46 PM
AUTO SETUP (IntelliBeam)
5
Press
/
to select BEAM+SOUND
OPTIMZ, BEAM OPTIMZ only or SOUND
OPTIMZ only and then press ENTER.
The following screen appears on your TV.
ENTER
6
Check the following points once again before
starting the AUTO SETUP procedure.
• Is the optimizer microphone firmly connected to
this unit?
• Is the optimizer microphone placed in a proper
location?
• Are there any large obstacles in between the
optimizer microphone and the walls in your
listening room?
7
Press ENTER to start the AUTO SETUP
procedure.
The following screen appears on your TV and the
AUTO SETUP procedure starts in 10 seconds.
Evacuate yourself from your listening room before
starting the AUTO SETUP procedure.
ENTER
AUTO SETUP
PREPARATION & CHECK
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
BEAM+SOUND OPTIMZ
(Beam optimization and sound optimizaiton)
Use to optimize the beam angle, delay, volume and quality
so that the parameters best match your listening
environment.
It is recommended that you should select this optimization
feature in the following cases:
• If you make settings for the first time.
• If the unit has been relocated.
• If your listening room has been restructured.
• If the objects in your listening room (furniture, etc.)
have been rearranged.
This menu takes about 3 minutes.
BEAM OPTIMZ only
(Beam optimization only)
Use to optimize the beam angle so that the parameter best
matches your listening environment.
This menu takes about 1 minute.
SETUP
ENTER
AUTO SETUP START
WILL BEGIN in 10SEC
Please leave the room.
**-------[RETURN]:Cancel
If an error occurs, an error buzzer is played and an
error message is displayed. See “Error messages for
AUTO SETUP” on page 35 for a complete list of
error messages and their proper remedies. Follow the
instructions and perform the AUTO SETUP
procedure again.
SOUND OPTIMZ only
(Sound optimization only)
Use to optimize the beam delay, volume and quality so
that the parameters best match your listening environment.
It is recommended that you should select this optimization
feature in the following cases:
• If you have opened or closed the curtains in your
listening room before using this unit.
• If you have manually set the beam angle.
This menu takes about 2 minutes.
English
Note
You must optimize the beam angle in the BEAM OPTIMZ only
procedure before starting the SOUND OPTIMZ only procedure.
33 En
AUTO SETUP (IntelliBeam)
8
Check that the following screen is displayed
on your TV.
The results of the AUTO SETUP procedure are
displayed on your TV.
10
Disconnect the optimizer microphone from
the OPTIMIZER MIC jack on the front panel.
Side view
Example 1
SHOW RESULT
MEASUREMENT COMPLETE
BEAM MODE :5 BEAM
SUBWOOFER :NOT APPLICABLE
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
Example 2
Optimizer microphone
SHOW RESULT
MEASUREMENT COMPLETE
ENVIRONMENT CHECK[FAILED]
BEAM MODE :5 BEAM
SUBWOOFER :YES
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
y
• If ‘‘ENVIRONMENT CHECK [FAILED]’’ is
displayed, we recommend running the AUTO SETUP
procedure again. For details, see step 9.
• If ‘‘SUBWOOFER : NOT APPLICABLE’’ is
displayed even though a subwoofer is connected to this
unit, increase the volume level of the subwoofer and
run the AUTO SETUP procedure again.
• Depending on the environment of your listening room,
the beam angle of front left and right, and surround left
and right may be set to the same value even if 5BEAM
is displayed as a result.
9
Press ENTER to confirm the results or press
RETURN to cancel the results.
The following screen is displayed temporarily for 2
seconds and then disappears from your TV.
AUTO SETUP COMPLETE
ENTER
Please remove the MIC from
the YSP and the listening
position.
If ‘‘ENVIRONMENT CHECK [FAILED]’’ is displayed in
step 8, the following screen is displayed after pressing
ENTER. In this case, see ERROR E-1 in “Error messages
for AUTO SETUP” on page 35. Press ENTER to exit the
AUTO SETUP and then run the procedure again from
step 3.
AUTO SETUP COMPLETE
Your YSP unit may not be set
up correctly.
We recommend you try again.
Please press [ENTER] key to
exit.
34 En
01EN_YSP-1100_UAB_EN.book Page 35 Wednesday, August 30, 2006 1:46 PM
AUTO SETUP (IntelliBeam)
■ Error messages for AUTO SETUP
Before the AUTO SETUP procedure starts
Error message
ERROR E-2
No MIC Detected. Please check
MIC connection and re-try.
Cause
The optimizer microphone is not
connected to this unit.
Remedy
Connect the optimizer microphone to
this unit.
See
page
30
While the AUTO SETUP procedure is in progress
If one of the errors shown below except E-1 is displayed, press RETURN. In case you have started the AUTO SETUP
procedure by pressing AUTO SETUP on the remote control in step 3, run the procedure again from step 3 after once the
screen disappears. In case you have started the AUTO SETUP procedure by pressing MENU on the remote control in step
3, run the procedure again from step 4 after the screen in step 3 is displayed. Run the MANUAL SETUP if the problem is
difficult to be saved.
Error message
Cause
Remedy
See
page
There is too much unwanted noise in
your listening room.
Make sure that your listening room is as
quiet as possible. You may want to
choose certain hours during the day
when there is not much noise coming
from outside.
—
ERROR E-2
No MIC detected. Please check
MIC connection and re-try.
The optimizer microphone was
disconnected while the AUTO SETUP
procedure was in progress.
Make sure that the optimizer microphone
is firmly connected to this unit.
30
ERROR E-3
Unexpected control is detected.
Please re-try.
Some other operations were performed
on this unit while the AUTO SETUP
procedure was in progress.
Do not perform any other operations
while the AUTO SETUP procedure is in
progress.
—
ERROR E-4
Please check MIC position. MIC
should be set in front of YSP.
The optimizer microphone is not placed
in front of this unit.
Make sure that the optimizer microphone
is installed in front of this unit.
30
ERROR E-5
Please check MIC position. MIC
should be set above 1.8m/6ft.
The optimizer microphone is not placed
in the right distance from this unit.
Make sure that the optimizer microphone
is installed more than 1.8 m from the
front of this unit and within 1 m from the
center height of this unit.
30
ERROR E-6
Volume level is lower than
expected. Please check MIC
position/connection and re-try.
The optimizer microphone cannot collect
the sound produced by this unit because
the sound output level is too low.
Make sure that the optimizer microphone
is firmly connected to this unit and
placed in a proper location. If the
problem persists, contact the nearest
YAMAHA service center for assistance.
30
ERROR E-7
Unexpected error happened.
Please re-try.
An internal system error occurred.
Repeat the AUTO SETUP procedure.
—
SETUP
ERROR E-1
Please test in quieter environment.
English
35 En
USING THE SYSTEM MEMORY
USING THE SYSTEM MEMORY
Convenient usage of the system
memory
3
You can save the current settings adjusted in SET MENU
in the system memory of this unit. It is handy to save
certain settings according to the varying conditions of
your listening environment. For example, if there are
curtains in the path of beams, the effectiveness of the
beams will vary depending on whether the curtains are
open or closed.
When the curtains are
open
Press
/
to select MEMORY and then
press ENTER.
The following screen appears on your TV.
ENTER
ENTER
When the curtains are
closed
;MEMORY
. 1)LOAD
2)SAVE
4
Saving settings
1
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
Press
/
to select SAVE and then press
ENTER.
The following screen appears on your TV.
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
ENTER
TV/AV
ENTER
YSP
2
Press MENU on the remote control.
The SET MENU screen appears on your TV.
SET MENU
MENU
y
• The control buttons used for SET MENU are displayed on
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN on the remote control.
• To cancel the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
36 En
MEMORY2
MEMORY3
[ ]/[ ]:Select
[ENTER]:Enter
p
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p MEMORY1
p
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
1)MEMORY SAVE
USING THE SYSTEM MEMORY
5
Press / to select MEMORY1, MEMORY2
or MEMORY3 and then press ENTER.
The following screen appears on your TV.
Loading settings
You can recall the settings saved in “Saving settings” on
page 36 according to the varying conditions of your
listening environment.
1
ENTER
ENTER
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
YSP
2)MEMORY SAVE
2
Press MENU on the remote control.
The SET MENU screen appears on your TV.
MEMORY1 Save Now ?
SET MENU
Push [ENTER] to Save
MENU
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
Press ENTER again.
The new parameters are saved as MEMORY1,
MEMORY2 or MEMORY3. Once the parameters are
saved, the display returns to the SET MENU screen.
SETUP
6
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
y
• The control buttons used for SET MENU are displayed on
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN on the remote control.
• To cancel the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
2)MEMORY SAVE
MEMORY1 Saving
ENTER
3
Press
/
to select MEMORY and then
press ENTER.
The following screen appears on your TV.
SET MENU
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
7
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
ENTER
ENTER
Press MENU to exit.
The SET MENU screen disappears from your TV.
;MEMORY
MENU
. 1)LOAD
2)SAVE
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
English
37 En
USING THE SYSTEM MEMORY
4
Press
/
to select LOAD and then press
ENTER.
The following screen appears on your TV.
6
Press ENTER again.
The new parameters are saved as MEMORY1,
MEMORY2 or MEMORY3. Once the parameters are
saved, the display returns to the SET MENU screen.
1)MEMORY LOAD
ENTER
ENTER
MEMORY1 Loading
ENTER
1)MEMORY LOAD
p MEMORY1
MEMORY2
MEMORY3
SET MENU
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
p
p
[ ]/[ ]:Select
[ENTER]:Enter
5
Press
/
to select MEMORY1,
MEMORY2 or MEMORY3 and then press
ENTER.
The following screen appears on your TV.
7
Press MENU to exit.
The SET MENU screen disappears from your TV.
MENU
ENTER
ENTER
1)MEMORY LOAD
MEMORY1 Load Now ?
Push [ENTER] to Load
38 En
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
PLAYBACK
PLAYBACK
Selecting the input source
You can play back sound from the components connected
to this unit simply by pressing INPUT on the front panel
repeatedly or pressing one of the input selector buttons
(TV, STB, VCR, DVD or AUX) on the remote control.
The name of the selected input source and the type of the
corresponding input mode appear in the front panel
display.
■ Front panel operations
Press INPUT on the front panel repeatedly to
toggle between TV, DVD, VCR and AUX.
The name of the corresponding input source and the type
of the current input mode are shown in the front panel
display.
■ Remote control operations
Set the operation mode selector to YSP to switch
to the operation mode of this unit and then press
TV on the remote control to play back a TV
program.
TV/AV
TV
YSP
VOL
INPUT
VOLUME
+
STANDBY/ON
Name of the selected
input source
STB
VCR
DVD
AUX
TV
INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
Set the operation mode selector to YSP to switch
to the operation mode of this unit and then press
STB on the remote control to play back a satellite
broadcast.
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
TV/AV
BASIC
OPERATION
INPUT1
Type of the selected
input mode
STB
YSP
OFF
0
+10
CH LEVEL
MENU
VOL
TV/AV
ENTER
YSP
TEST
RETURN
Set the operation mode selector to YSP to switch
to the operation mode of this unit and then press
DVD on the remote control to play back a DVD.
TV/AV
DVD
YSP
VOL
English
39 En
01EN_YSP-1100_UAB_EN.book Page 40 Wednesday, August 30, 2006 1:46 PM
PLAYBACK
Set the operation mode selector to YSP to switch
to the operation mode of this unit and then press
VCR on the remote control to play back a video
tape.
TV/AV
VCR
Playing back sources
Once an input source is selected (see page 39), you can
play back the selected input source.
Note
YSP
This section uses a DVD player as an example of the playback
source.
y
VOL
Set the operation mode selector to YSP to switch
to the operation mode of this unit and then press
AUX on the remote control to play back a
component connected to the AUX jack on the
rear panel of this unit.
TV/AV
For details on the TV and the DVD player you are using, refer to
the owner’s manual supplied with the TV and the DVD player.
1
Turn on the power of your DVD player using
the remote control supplied with the DVD
player.
2
Switch to the video input on your TV using
the remote control supplied with the TV so
that the DVD menu screen is displayed.
3
If necessary, turn down the volume of your
TV until you cannot hear any sound.
4
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
AUX
YSP
VOL
TV/AV
YSP
5
Press DVD on the remote control to select
DVD as the input source.
DVD
6
Play back the DVD on your DVD player using
the supplied remote control.
Audio signals from your DVD player are output from
this unit.
y
• You can check the digital signal being input at the DVD player
with the digital connection (optical/coaxial). Press ST+3BEAM
on the remote control while playing back a DVD recorded in 5.1
DIGITAL or
channel. The
indicator lights up when
this unit detects the 5.1 channel signal input at the optical/
coaxial jack. If the PCM indicator lights up, confirm the
settings of the digital output, bitstream output, and/or DTS
output of the DVD player.
• If the output volume is too low, increase the volume on this unit
to around 45.
• If you have set the appropriate remote control codes for your
TV and DVD player, you can use the remote control supplied
with this unit to operate these components. For details on how
to set remote control codes, see page 81.
40 En
PLAYBACK
Adjusting the volume
Muting the sound
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
CODE SET
1
INPUT
VOLUME
+
STANDBY/ON
Press MUTE on the remote control to mute
the sound.
AUDIO MUTE ON appears in the front panel
display, and the volume level indicator flashes.
MUTE
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
VOL
CODE SET
Flashes
VOL
2
VOLUME
or
VOLUME
+
Front panel
Press MUTE on the remote control again (or
press VOLUME +/–) to resume the sound
output.
AUDIO MUTE OFF appears temporarily in the front
panel display (or the numeric value of the current
volume level appears if you press VOLUME +/–),
and the volume level indicator lights up.
Remote control
BASIC
OPERATION
Press VOLUME +/– on the front panel or on the
remote control to increase or decrease the
volume level.
The numeric value of the volume level appears in the front
panel display.
Control range: MIN (minimum), 01 to 99,
MAX (maximum)
VOLUME
MUTE
or
VOL
Lights up
Notes
• The volume level of all input sources (including multi-channel
as well as stereo sources) changes at the same time.
• One of the volume level increases or decreases each time you
press VOLUME +/–.
• You can continuously increase or decrease the volume level if
you press and hold VOLUME +/–.
VOL
Note
y
You can select whether the sound output is to be muted
completely or by 20 dB when you press MUTE (see page 67).
41 En
English
The sound output of all input sources (including multi-channel as
well as stereo sources) is muted at the same time.
01EN_YSP-1100_UAB_EN.book Page 42 Wednesday, August 30, 2006 1:46 PM
ENJOYING SURROUND SOUND
ENJOYING SURROUND SOUND
You can enjoy multi channel surround sound by changing the beam mode using the beam mode buttons on the remote
control. Select 3 beam, 5 beam and stereo plus 3 beam for multi channel playback.
Note
When ANGLE TO WALL OR CORNER is set in MANUAL SETUP (see page 62), 5 beam and 3 beam cannot be selected.
5 beam
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
1
STEREO
ST+3BEAM
3BEAM
2
3
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
OFF
0
+10
CH LEVEL
MENU
Outputs sound beams from the front left and right, center,
and surround left and right channels. This mode is ideal
for enjoying surround sound effects to the fullest when
watching DVDs recorded in a multi-channel format or
playing back 2-channel sources in a multi-channel format.
Press 5BEAM on the remote control to select the
5 beam.
TV/AV
ENTER
YSP
5BEAM
RETURN
TEST
1
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
Notes
TV/AV
YSP
2
Press one of the beam mode buttons
(5BEAM, ST+3BEAM or 3BEAM) to select the
desired beam mode for 5.1-channel play
back.
42 En
5BEAM
ST+3BEAM
3BEAM
1
2
3
• To achieve the best surround sound effect, make sure that there
are no obstacles placed in the path of sound beams in that the
objects may prevent the beams from rebounding directly off the
walls in your listening room.
• The front left and right sound beams are output towards the
walls in your listening room.
• If you press 5BEAM, “SP Pos. Corner!” appears in the front
panel display when INSTALLED POSITION is set to ANGLE
TO WALL OR CORNER.
01EN_YSP-1100_UAB_EN.book Page 43 Wednesday, August 30, 2006 1:46 PM
ENJOYING SURROUND SOUND
Stereo plus 3 beam
3 beam
Outputs normal sound from the front left and right
channels and sound beams from the center and surround
left and right channles. This mode is ideal for watching
live recordings on a DVD. Vocals and instrumental sounds
can be heard close to the center of the listening position
while sound reflections from the venue itself can be heard
on your right and left, giving you the feeling that you are
sitting right in front of the stage.
Outputs sound beams from the front left and right and
center channels. This mode is ideal for enjoying movies
with the whole family. Because the listening position area
is widened, you can enjoy excellent quality surround
sound over a wider area. In addition, you can use this
mode when the listening position is close to the backside
of the wall and the surround left and right beams cannot
reflect.
Press ST+3BEAM on the remote control to select
the stereo plus 3 beam.
Press 3BEAM on the remote control to select the
3 beam.
ST+3BEAM
2
3BEAM
3
y
You can achieve a more realistic surround effect if you adjust
settings for IMAGE LOCATION in BEAM MENU (see page 66).
Notes
Note
• When you play back multi-channel sources, surround left and
right signals are mixed down and output from the front left and
right channels.
• The front left and right sound beams are output towards the
walls in your listening room.
• If you press 3BEAM, “SP Pos. Corner!” appears in the front
panel display when INSTALLED POSITION is set to ANGLE
TO WALL OR CORNER.
BASIC
OPERATION
The front left and right sound beams are output directly to the
listening position.
English
43 En
ENJOYING SURROUND SOUND
■ Decoder indicators
Depending on the input source and the selected surround
mode, the indicators in the front panel display light up as
follows:
Status
When PCM signals are being
input
Indicator
PCM
When DTS digital signals are
being input or when DTS Neo:6
is selected
When Dolby Digital signals are
being input
When Dolby Pro Logic is
selected
When Dolby Pro Logic II is
selected
Recommended
source
Surround mode
Dolby Pro Logic
–
All sources
Dolby Pro Logic II
Movie
Music
Game
Movies
Music
Games
DTS Neo:6
Cinema
Music
Movies
Music
Notes
DIGITAL
PL
PL
y
• You can select an input mode (AUTO, DTS or ANALOG) by
pressing INPUTMODE on the remote control repeatedly (see
page 75).
• Discs encoded in DTS-ES or Dolby Digital 5.1 EX will be
played back in DTS or Dolby Digital.
44 En
■ Surround modes and recommended
sources
• Surround modes are available when the beam mode is set to a
setting other than the stereo playback or the my beam as the
beam mode.
• When you select an input source (see page 39), the surround
mode used for the previously selected input source is selected.
• If the power of this unit is turned off and on again, the surround
mode used for the previously selected input source before the
power was turned off is selected.
• The surround modes are available only when the CINEMA DSP
programs are turned off (see page 54) or when the movie
program is selected as the CINEMA DSP program (see
page 52).
• Only Dolby Pro Logic, Dolby Pro Logic II Movie and DTS
Neo:6 Cinema are available when the movie program is selected
as the CINEMA DSP program (see page 52).
• If the surround modes are not available, “Prohibit” appears in
the front panel display when you press SURROUND on the
remote control.
• The surround modes are available only when 2-channel signals
are being input. If you try to switch between the surround
modes when 5.1 channel signals are being input, “Prohibit”
appears in the front panel display.
ENJOYING SURROUND SOUND
Enjoying 2-channel sources
in surround sound
This unit can decode 2-channel sources for 5.1 channel
playback so that you can enjoy a variety of surround sound
effects by switching the surround mode.
2
Press SURROUND on the remote control
repeatedly (or press SURROUND and then
press / ) to switch between surround
modes.
SURROUND
y
6
The surround modes are available only when the CINEMA DSP
programs are turned off (see page 54) or when the movie program
is selected as the CINEMA DSP program (see page 52). In
addition, the beam mode must be set to the 5 beam, the stereo
plus 3 beam or the 3 beam (see page 42).
or
SURROUND
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
6
ENTER
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
OFF
0
+10
CH LEVEL
MENU
PRO LOGIC
TV/AV
ENTER
YSP
RETURN
TEST
PLII Movie
PLII Music
1
TV/AV
PLII Game
Neo:6 Cinema
YSP
Neo:6 Music
BASIC
OPERATION
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
Example of the surround
mode display in the front
panel display when the
CINEMA DSP program is
turned off
English
45 En
ENJOYING SURROUND SOUND
Adjusting surround mode
parameters
You can configure the parameters for Dolby Pro Logic II
Music and DTS Neo:6 Music to fine-tune the surround
sound effect.
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
OFF
0
+10
CH LEVEL
MENU
TV/AV
ENTER
YSP
RETURN
TEST
1
2
Repeat steps 1 and 2 in “Enjoying 2-channel
sources in surround sound” on page 45 and
select PL II Music or Neo:6 Music.
Press
/
to select the parameter.
ENTER
3
Press
/
to configure the parameter.
ENTER
46 En
■ When Dolby Pro Logic II Music is
selected
PANORAMA
Gives front left and right channel sound a wraparound
effect, distributed throughout the entire surround
sound field to give you an expansive feeling.
Choices: ON/OFF
Default setting: OFF
DIMENSION
Adjusts the difference in volume between front and
surround channels to the volume balance you desire.
Control range: –3 (toward the surround direction) to
+3 (toward the front direction)
Default setting: STD
CT WIDTH
Distributes the center channel sound to the left and
right. If set to 0, center channel sounds output only
from the center channel.
Control range: 0 to 7
Default setting: 3
■ When DTS Neo:6 Music is selected
C. IMAGE
Adjusts the center image from three channels (front
and center) to varying degrees.
Control range: 0.0 (wider) to 1.0 (toward the center)
Default setting: 0.3
ENJOYING STEREO SOUND
ENJOYING STEREO SOUND
Stereo playback
Notes
You can enjoy 2-channel stereo playback by changing the
beam mode to the stereo playback using the beam mode
buttons on the remote control. The normal sounds are
output from the front and left channels in the 2-channel
stereo. This is ideal for playing back hi-fi sources, such as
CDs, and can be used to replace your TV speakers.
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
• When you play back multi-channel sources, all signals except
those for the front left and right channels are mixed down and
output from the front left and right channels. No audio is output
from the center and rear channels.
• The surround mode becomes disabled when the stereo playback
is selected as the beam mode.
• When you play back Dolby Digital audio signals in the stereo
playback, the dynamic range becomes compressed. If the
volume level decreases to the extreme, use other beam modes
except the my beam.
• If the stereo playback is selected as the beam mode, the
surround modes (see page 44) and the CINEMA DSP programs
(see page 52) become ineffective.
OFF
0
+10
CH LEVEL
MENU
TV/AV
ENTER
YSP
RETURN
TEST
BASIC
OPERATION
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
YSP
2
Press STEREO on the remote control to
select the stereo playback as a beam mode.
STEREO
4
English
47 En
PLAYING BACK SOUND CLEARLY (MY BEAM)
PLAYING BACK SOUND CLEARLY (My beam)
You can improve listenability in a noisy environment by changing the beam mode to the my beam, outputs sound beams
directly to the listening position in a single channel. In addition, the my beam is also ideal if you do not want the sound
beams to be reflected on the walls in your listening room or if you do not disturb others asleep while enjoying music or
movies at night.
My beam
microphone
POWER POWER
STANDBY/ON
AV
TV
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
OFF
0
+10
CH LEVEL
MENU
TV/AV
ENTER
YSP
RETURN
TEST
Note
If the my beam is selected as the beam mode, the surround modes (see page 44), the CINEMA DSP programs (see page 50) and the
TruBass (see page 57) become ineffective. In addition, no audio is output from the subwoofer connected to this unit.
Using auto-adjust function
The my beam microphone on the remote control collects
the test tones from this unit, and then the beam angle is
automatically adjusted.
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
YSP
2
Press and hold MY BEAM on the remote
control more than 2 seconds.
A test tone is output twice from this unit. Keep
pointing the remote control toward this unit during
the test tones are being output so that the my beam
microphone can collect the test tones.
Control range: L50° to R50°
Operation guarantee range: 6 m, L30° to R30°
MY BEAM
5
48 En
Notes
• If an error occurs, an error buzzer is played and MY BEAM
ERROR is displayed on the front panel display.
• An error may occur if the listening room is noisy. Make sure
that the listening room is as quiet as possible during the test
tones are being output.
• Do not shake or move the remote control during the test tones
are being output.
• Do not cover the my beam microphone on the remote control
during the test tones are being output.
• The batteries in the remote control may be week if the remote
control does not function properly. In such case, replace all the
batteries and then try the procedure again.
PLAYING BACK SOUND CLEARLY (My beam)
Using manual-adjust function
You can adjust the beam angle manually while playing
back an input source. This function is also ideal if the
listening position is out of the operation guarantee range
of the auto-adjust function.
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
YSP
2
Press MY BEAM on the remote control.
MY BEAM is displayed in the front panel display.
MY BEAM
5
3
Press / while MY BEAM is displayed to
adjust the angle.
Control range: L90° to R90°
• Press repeatedly to increase the horizontal angle
on the left side.
BASIC
OPERATION
• Press repeatedly to increase the horizontal angle
on the right side.
ENTER
VOL
English
49 En
USING SOUND FIELD PROGRAMS
USING SOUND FIELD PROGRAMS
This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from
stereo or multi-channel sources. This unit is also equipped with a YAMAHA CINEMA DSP (digital sound field
processing) chip containing several sound field programs which you can use to enhance your playback experience. Most
of the sound field programs are precise digital recreations of actual acoustic environments found in famous concert halls,
music venues and movie theaters.
y
The YAMAHA CINEMA DSP modes are compatible with all Dolby Digital, DTS and Dolby Surround sources.
Note
Choose a sound field program based on your listening preference and do not purely rely on the name of the sound field program itself.
What is a sound field?
A significant factor that creates the rich, full tones of a live instrument are the multiple reflections from the walls of the
room. In addition to making the sound live, these reflections enable the listener to tell where the player is situated as well
as the size and shape of the room in which the listening is sitting.
■ Elements of a sound field
In any environment, there are two distinct types of sound reflections that combine with the direct sound coming straight
to our ears from the player’s instrument to make up the sound field.
Early reflections
Reflected sounds reach our ears extremely rapidly (50 ms to 80 ms after the direct sound) after reflecting from one
surface only (from the ceiling or a wall, for example). Early reflections help add clarity to the direct sound.
Reverberations
These are caused by reflections from more than one surface (i.e. wall, ceiling, the back of the room, etc.) so numerous
that they merge together to form a continuous sonic afterglow. They are non-directional and lessen the clarity of the direct
sound.
Direct sound, early reflections and subsequent reverberation taken together help us to determine the subjective size and
shape of the room, and it is this information that the digital sound field processor reproduces in order to create sound
fields.
If you could create the appropriate early reflections and subsequent reverberations in your listening room, you would be
able to create your own listening environment. The acoustics in your room could be changed to those of a concert hall, a
dance floor or a listening room of virtually any size at all. This ability to create sound fields at will is exactly what
YAMAHA has done with the CINEMA DSP technology.
50 En
USING SOUND FIELD PROGRAMS
Sound field program descriptions
You can select from the following sound field programs based on your listening preference when you play music, movie
or sports sources. For details on how to switch between the available sound field programs, see page 52.
Note
There is only one sports sound field program available.
Sound field program
Source
Feature
Music Video
This program produces a vibrant environment and lets you feel as if
you are at an actual jazz or rock concert.
Concert Hall
This program creates a rich surround effect of a large round concert
hall with a great deal of presence, emphasizing the extension of
sounds, and lets you feel as if you are seated close to the center of the
stage.
Music
Jazz Club
This program recreates the acoustic environment of “The Bottom
Line”, a famous jazz club in New York and lets you feel as if you are
seated right in front of the stage.
Sci-Fi
This program clearly reproduces dialogs and special sound effects of
the latest science fiction films and lets you feel a broad and expansive
cinematic space amid silence.
Spectacle
Movie
Sports
This program reproduces the energetic environment of live sports
broadcasting, converging a commentator’s voice on the center and
broadening the overall atmosphere of the stadium, and lets you feel as
if you are seated at an actual stadium or a ball park.
BASIC
OPERATION
This program reproduces the thrilling environment of the latest action
films and lets you feel the dynamic and excitement of fast-moving
scenes.
Adventure
SPORTS
This program reproduces the wide and grand environment and lets you
have added impressions on spectacular scenes with strong visual
impacts.
English
51 En
USING SOUND FIELD PROGRAMS
Turning on CINEMA DSP programs
3
You can select from three different sound field programs
(MUSIC, MOVIE and SPORTS) depending on the type of
sources you want to enjoy.
Check that MUSIC is displayed in the front
panel display and then press MUSIC on the
remote control repeatedly (or press / on
the remote control) to switch between the
music sound field programs.
Notes
• The CINEMA DSP programs are not available if the stereo
playback (see page 47) or the my beam (see page 48) is selected
as the beam mode.
• If the CINEMA DSP programs are not available, “Prohibit”
appears in the front panel display when you press one of the
sound field program buttons on the remote control.
VOL
MUSIC
5BEAM
ST+3BEAM
3BEAM
2
3
1
STEREO
7
or
ENTER
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
Music Video
OFF
+10
0
CH LEVEL
Concert Hall
MENU
Jazz Club
TV/AV
ENTER
YSP
RETURN
TEST
y
For detailed descriptions of each sound field program, see “Sound
field program descriptions” on page 51.
■ Music programs
Select this sound field program when you play music
sources. This program produces a vibrant atmosphere and
lets you feel as if you are seated in an actual rock or jazz
concert hall.
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
■ Movie programs
Select this sound field program when you play movie
sources, especially the ones encoded in Dolby Digital,
DTS or Dolby Surround. This program clearly reproduces
dialog and sound effects, thus creating a broad and
expansive cinematic space amid silence.
1
TV/AV
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
YSP
TV/AV
YSP
2
Press MUSIC on the remote control to select
the music sound field program.
MUSIC
7
2
Press MOVIE on the remote control to select
the movie sound field program.
MOVIE
8
52 En
USING SOUND FIELD PROGRAMS
3
Check that MOVIE is displayed in the front
panel display and then press MOVIE on the
remote control repeatedly (or press / on
the remote control) to switch between the
music sound field programs.
VOL
MOVIE
or
8
ENTER
Sci-Fi
Spectacle
Adventure
y
For detailed descriptions of each sound field program, see “Sound
field program descriptions” on page 51.
BASIC
OPERATION
■ Sports program
Select this sound field program when you play sports
sources. This program densely concentrates the vocal
sound of the commentator in the center while broadening
the sound from the audience or the environment all around
your listening room.
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
YSP
2
Press SPORTS on the remote control to
select the sports sound field program.
SPORTS
9
VOL
English
y
• There is only one sports sound field program available.
• For detailed descriptions of each sound field program, see
“Sound field program descriptions” on page 51.
53 En
USING SOUND FIELD PROGRAMS
Turning off CINEMA DSP programs
Adjusting CINEMA DSP effect levels
Turn off the CINEMA DSP programs if you want to enjoy
the original sound without the sound field program effect.
You can enjoy good quality sound with the factory preset
parameters. However, you can also adjust the effect level
of the CINEMA DSP programs relative to the level of the
direct sound so that each sound field program can reflect
your listening environment and your preference even more
accurately.
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
1
TV/AV
YSP
2
Press OFF on the remote control to turn off
the sound field programs.
CINEMA DSP OFF is shown in the front panel
display.
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
YSP
2
OFF
0
Press MUSIC, MOVIE or SPORTS on the
remote control to select the desired sound
field program.
MUSIC
7
MOVIE
or
8
SPORTS
or
9
VOL
3
Press
/
on the remote control.
DSP LEVEL is shown in the front panel display.
VOL
4
Press / on the remote control to adjust
the effect level of the CINEMA DSP programs.
ENTER
Control range: –6 dB to +3 dB
• A larger value increases the effect level.
• A smaller value decreases the effect level.
54 En
USING THE VOLUME MODE (NIGHT LISTENING MODE/TV VOLUME EQUAL MODE)
USING THE VOLUME MODE
(Night listening mode/TV volume equal mode)
The night listening modes are designed to improve listenability at lower volumes or at night. In addition, you can limit
the volume level of the TV so that it will not vary suddenly to a great extent whenever the contents being broadcast
change (i.e. due to commercials, etc.).
INPUT1
TV
INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
2
Press VOL MODE on the remote control
repeatedly to select NIGHT:CINEMA,
NIGHT:MUSIC, TV EQUAL VOL or OFF.
VOL MODE
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
OFF
0
+10
CH LEVEL
MENU
TV/AV
NIGHT:CINEMA
ENTER
YSP
RETURN
TEST
1
NIGHT:MUSIC
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
YSP
OFF
The NIGHT indicator lights up in the front panel
display when NIGHT:CINEMA or NIGHT:MUSIC
is selected.
BASIC
OPERATION
TV/AV
TV EQUAL VOL
NIGHT
Lights up
• Select NIGHT:CINEMA when watching films to
reduce the dynamic range of film soundtracks and
make dialog easier to hear at lower volumes.
• Select NIGHT:MUSIC when listening to music
sources to preserve ease-of-listening for all sounds.
• Select TV EQUAL VOL when watching TV
programs.
• Select OFF to turn off the volume mode.
English
55 En
USING THE VOLUME MODE (Night listening mode/TV volume equal mode)
3
Press / on the remote control to adjust
the effect level of compression while
NIGHT:CINEMA, NIGHT:MUSIC or TV EQUAL
VOL is displayed.
ENTER
Effect.Lvl:MIN
Effect.Lvl:MID
Effect.Lvl:MAX
• Select Effect.Lvl:MIN for minimum compression.
• Select Effect.Lvl:MID for standard compression.
• Select Effect.Lvl:MAX for maximum
compression.
Note
The volume mode settings are canceled if you press
STANDBY/ON on the front panel or on the remote control
or if you disconnect the power supply cable from the AC
wall outlet.
56 En
USING BASS SOUND ENHANCER (TRUBASS)
USING BASS SOUND ENHANCER (TruBass)
This unit can produce the perception of an improved low frequency performance with the aid of the SRS TruBass
technology, which improves bass even without a subwoofer and provides deeper, richer bass in the presence of a
subwoofer.
Note
The TruBass is not available when the my beam is selected as the beam mode (see page 48).
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
3
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
Press
on the remote control repeatedly
to select TruBass MID or TruBass DEEP.
You can select TruBass MID or TruBass DEEP
depending on the type of material you are playing.
OFF
0
+10
CH LEVEL
MENU
TV/AV
ENTER
YSP
RETURN
TEST
VOL
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
or
TV/AV
YSP
2
Press
on the remote control.
The current setting (TruBass MID, TruBass DEEP, or
TruBass OFF) is shown in the front panel display.
• Select TruBass MID for standard effects.
• Select TruBass DEEP for maximum effects.
• Select TruBass OFF to turn off the TruBass.
BASIC
OPERATION
VOL
VOL
or
VOL
or
English
VOL
57 En
USING THE SLEEP TIMER
USING THE SLEEP TIMER
Use this feature to automatically set this unit to the standby mode after a specified time period. The sleep timer is useful
if you are going to sleep after a certain amount of time while this unit is still playing back a source.
Each time you press SLEEP on the remote control,
the front panel display changes as shown below.
Setting the sleep timer
SLEEP
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
SLEEP
120min
SLEEP
90min
SLEEP
60min
SLEEP
30min
SLEEP
OFF
OFF
0
+10
CH LEVEL
MENU
TV/AV
ENTER
YSP
RETURN
TEST
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
3
TV/AV
YSP
2
Press SLEEP on the remote control
repeatedly to set the amount of time for the
sleep timer.
Choices: 120min, 90min, 60min, 30min, OFF
The SLEEP indicator in the front panel display
flashes while switching the amount of time for the
sleep timer.
SLEEP
SLEEP
Flashes
58 En
Wait for a few seconds without operating this
unit to confirm the setting for the sleep timer.
The SLEEP indicator lights up in the front panel
display, indicating that the sleep timer is activated.
SLEEP
Lights up
USING THE SLEEP TIMER
Canceling the sleep timer
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
YSP
2
Press SLEEP on the remote control
repeatedly so that SLEEP OFF appears in the
front panel display.
SLEEP
VOL
SLEEP
3
OFF
BASIC
OPERATION
Wait for a few seconds without operating this
unit to confirm the setting for the sleep timer.
The SLEEP indicator disappears from the front panel
display, indicating that the sleep timer is deactivated.
SLEEP
Disappears
Note
The previous setting for the sleep timer before you deactivate it is
stored in the system memory and automatically restored when
you make a new setting next time.
y
The sleep timer setting can also be deactivated if you press
STANDBY/ON on the front panel or on the remote control to set
this unit to the standby mode or unplug the power supply cable
from the AC outlet.
English
59 En
MANUAL SETUP
MANUAL SETUP
To achieve the best quality surround sound, you can use MANUAL SETUP to fine-tune the listening environment
parameters, as well as to make advanced settings for sound signals, sound beams, digital input and the OSD. Change the
initial settings (indicated in bold under each parameter) to reflect the needs of your own listening environment.
y
• You can save the settings optimized by the AUTO SETUP procedure (see page 36). A set of settings optimized according to specific
conditions of your listening environment can be recalled later depending on the varying conditions of your listening environment (see
page 37).
• Most of the parameters in SOUND MENU and BEAM MENU are automatically set when you run AUTO SETUP (see page 29). Use
SOUND MENU and BEAM MENU to make additional adjustments.
• BEAM MENU allows you to make settings for the surround sound effects normally available in the speaker settings menu.
• Make settings for the parameters in BEAM MENU first before you make settings for the parameters in SOUND MENU, INPUT
MENU and DISPLAY MENU.
SOUND MENU
Use to manually adjust various parameters related to the sound output.
Item
Features
Page
TONE CONTROL
Adjusts the output level of high-frequency or low-frequency sound.
66
SUBWOOFER SET
Adjusts the various subwoofer settings.
67
MUTE LEVEL
Adjusts the muting level.
67
AUDIO DELAY
Adjusts audio delay.
67
ROOM EQ
Adjusts the tonal quality of the listening room.
67
DD/DTS Dynamic Range
Adjusts the dynamic range of Dolby Digital or DTS signals.
68
BEAM MENU
Use to manually adjust various parameters related to the sound beam output.
Item
Features
Page
SETTING PARAMETERS
Adjusts listening room and listening position settings.
62
BEAM ADJUSTMENT
Adjusts various beam settings.
63
IMAGE LOCATION
Adjusts the sound position of the front left and right channels.
66
INPUT MENU
Use to manually adjust various parameters related to the audio and video input.
Item
Features
Page
INPUT ASSIGNMENT
Assigns jacks according to the component to be used.
68
INPUT MODE
Selects the initial input of the source.
69
INPUT TRIM
Adjusts the input level of the source.
69
INPUT RENAME
Renames the displayed input source.
70
DISPLAY MENU
Use to manually adjust various parameters related to the display.
Item
Features
Page
DIMMER SET
Adjusts the brightness of the display.
70
OSD SET
Adjusts the display position and the background color of the OSD.
71
UNIT SET
Changes the display unit of measurement.
71
60 En
MANUAL SETUP
Using MANUAL SETUP
3
Use the remote control to access and adjust each
parameter.
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
Press
/
to select MANUAL SETUP and
then press ENTER.
The following screen appears on your TV.
ENTER
ENTER
OFF
0
+10
CH LEVEL
MENU
TV/AV
ENTER
;MANUAL SETUP
YSP
RETURN
TEST
. 1)SOUND MENU
2)BEAM MENU
3)INPUT MENU
4)DISPLAY MENU
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
y
You can adjust the SET MENU parameters while the unit is
reproducing sound.
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
4
Press
/
to select a sub menu and then
press ENTER.
TV/AV
YSP
ENTER
2
ENTER
Press MENU on the remote control.
The SET MENU screen appears on your TV.
SET MENU
MENU
5
Press
/
/ /
each parameter.
and ENTER to configure
ADVANCED
OPERATION
. ;MEMORY
;AUTO SETUP
;MANUAL SETUP
;LANGUAGE SETUP
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
y
• The control buttons used for SET MENU are displayed on
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN on the remote control.
• To cancel the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
ENTER
6
Press MENU to exit.
The OSD disappears from your TV screen.
MENU
English
61 En
MANUAL SETUP
BEAM MENU
Use to manually adjust various parameters related to the
sound beam output.
SET MENU → MANUAL SETUP → BEAM MENU
• Select FLAT TO WALL if this unit is installed in
parallel with the wall in your listening room. Adjust the
width and length of your listening room as well as the
distance of the listening position from this unit and the
distance of the center of this unit from the left wall.
Listening position
from the left wall
2)BEAM MENU
. A)SETTING PARAMETERS
B)BEAM ADJUSTMENT
C)IMAGE LOCATION
Listening position
from the unit
p
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
Room length
y
Use to set the position of this unit in your listening room
and the distance of this unit from the listening position.
When you make settings for each parameter, other related
parameters are automatically adjusted to best match your
listening environment.
Choices for the room width and length:
2.0 m to 12.0 m
Choices for the listening position from this unit:
1.8 m to 9.0 m
Choices for the listening position from the left wall:
0.6 m to 11.4 m
A)SETTING PARAMETERS 2/3
Note
INSTALLED HEIGHT;;;;1.0m
p
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
p
A)SETTING PARAMETERS 1/3
. INSTALLED POSITION
;;;;;FLAT TO WALL
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
p
If you make adjustments in SETTING PARAMETERS, the beam
optimization settings made in the AUTO SETUP procedure will
be lost. If you want to keep the beam optimization settings made
in the AUTO SETUP and make further adjustments, adjust
settings in BEAM ADJUSTMENT first (see page 63).
|
-------[ 5.4m ]|
4.9m
|
Room width and length
A)SETTING PARAMETERS 3/3
Listening position from the
unit and the left wall
--------|
2.7m [ 2.5m ]
|
p
p
■ SETTING PARAMETERS
(Setting parameters)
Room width
p
You can adjust the sound beam output level of each channel in
“ADJUSTING THE AUDIO BALANCE” (see page 72).
INSTALLED POSITION
(Installed position of this unit)
Use to adjust the installed position of this unit.
Choices: FLAT TO WALL (Parallel to wall installation),
ANGLE TO WALL OR CORNER
(Corner installation)
FLAT TO WALL
62 En
ANGLE TO WALL
OR CORNER
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
MANUAL SETUP
• Select ANGLE TO WALL OR CORNER if this unit is
installed in the corner in your listening room. Adjust
the width and length of your listening room as well as
the distance of the listening position from this unit.
INSTALLED HEIGHT (Installed height of this unit)
Use to adjust the installed height of this unit.
Control range: 0.0 m to 3.0 m
Initial setting: 1.0 m
Listening position
from the unit
Room width
Room length
Choices for the room width and length:
2.0 m to 12.0 m
Choices for the listening position from this unit:
1.8 m to 9.0 m
A)SETTING PARAMETERS 2/3
----- 5.4m --|
[ 5.4m ]
|
|
p
p
Room width and length
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
A)SETTING PARAMETERS 3/3
Listening position from
the unit
\
[ 2.5m ]
\
0.0 m to 3.0 m
■ BEAM ADJUSTMENT (Beam adjustment)
Use to manually adjust the various beam settings. We
recommend that you select 5 beam as the beam mode
before adjusting these parameters.
Notes
• When INSTALLED POSITION is adjusted in MANUAL
SETUP (see page 62), the factory default value is automatically
set for this parameter except CENTER in FOCAL LENGTH
(see page 65).
• Depending on the beam mode settings (see pages 42 and 47),
some channel positions may not be available for selection. In
this case, “– –” is displayed. When using the stereo plus 3 beam
as the beam mode, set the surround left and right signals to be
output from the front left and right channels.
p
p
Floor
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
Note
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
When you set the INSTALLED POSITION parameter in
MANUAL SETUP (see page 62), the parameters newly set for
the width and length of your listening room are automatically set
as the factory default value.
ADVANCED
OPERATION
B)BEAM ADJUSTMENT
. a)HORIZONTAL ANGLE
b)VERTICAL ANGLE
c)BEAM TRAVEL LENGTH
d)FOCAL LENGTH
e)TREBLE GAIN
English
63 En
MANUAL SETUP
HORIZONTAL ANGLE (Horizontal angle)
Use to adjust the horizontal angle of beams for each
channel. By adjusting the horizontal angle of the beams,
you can optimize the sound beam paths. A test tone is
automatically output.
( )
(+)
(+)
( )
BEAM TRAVEL LENGTH (Beam travel length)
A certain amount of delay must be applied to the sound
from each channel so that all sound will arrive at the
listening position at the same time. This menu sets the
distance that sound beams travel after being output and
reflected off the wall until they arrive at the listening
position and adjust the delay applied to the respective
channel.
The lines in the illustration below indicate the distance.
Choices: L90° to R90°
Adjust towards L (left) to move the direction of the output
to the left and adjust towards R (right) to move it to the
right.
a)HORIZONTAL ANGLE5 beam
1/5
Front L
L65deg
L90
R90
*
p
p
p
p 0(deg)
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
VERTICAL ANGLE (Vertical angle)
Use to adjust the vertical angle of sound beams for each
speaker. By altering the beam path, you can optimize
sound beam angles.
Choices: 0.3 m to 24.0 m
• Front L adjusts the distance the front left channel
sound beams travel.
• Front R adjusts the distance the front right channel
sound beams travel.
• Center adjusts the distance the center channel sound
beams travel.
• Surround L adjusts the distance the surround left
channel sound beams travel.
• Surround R adjusts the distance the surround right
channel sound beams travel.
c)BEAM TRAVEL LENGTH
5 beam
. Front L;;;;;;;6.0m
Front R;;;;;;;6.0m
Center;;;;;;;;2.5m
Surround L;;;;9.1m
Surround R;;;;9.1m
p
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
0°
y
Choices: –45° to +45°
Initial setting: 0°
• Adjust towards – (minus) to move the angle downward.
• Adjust towards + (plus) to move the angle upward.
b)VERTICAL ANGLE 1/5
5 beam
(+)
------0deg.
(-)
p
p
Front L
0deg.
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
Note
A test tone is automatically output.
64 En
We recommend that you use the setting optimized by the AUTO
SETUP (see page 29). Set this menu only when you changed the
HORIZONTAL ANGLE (see page 64).
MANUAL SETUP
FOCAL LENGTH (Focal length)
Use to set the distance from the front of this unit to the
focal point of output for each channel and adjust an
expansive feeling of each channel.
The focal points except the center channel should be set
near the reflection points on the walls. The shorter the
distance, more the expansion.
TREBLE GAIN (Treble gain)
Use to adjust the high frequency output level of each
channel.
y
If the reflection point of the front left and right or surround left
and right sound beams is a curtain or other acoustically absorbent
surface, you can achieve more effective surround sound by
increasing the treble level for those sound beams.
focal length
focal point
sweet spot
Center channel
( )
(+)
e)TREBLE GAIN
-5beam+
. Front L;;;;;;;;0dB -----Front R;;;;;;;;0dB -----Center;;;;;;;;;0dB -----Surround L;;;;;0dB -----Surround R;;;;;0dB ------
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
p
ADVANCED
OPERATION
Choices: –1.0 m to +13.0 m
Adjust towards – (minus) to move the focus outward and
adjust towards + (plus) to move the focus towards the
normal position.
• Front L adjusts the focal length for the front left sound
beams.
• Front R adjusts the focal length for the front right
sound beams.
• Center adjusts the focal length for the center sound
beams. Initial setting: –0.5 m
• Surround L adjusts the focal length for the surround
left sound beams.
• Surround R adjusts the focal length for the surround
right sound beams.
p
Front left channel
Choices: –12.0 dB to +12.0 dB
Initial setting: 0 dB
• FL adjusts the high frequency output level of the front
left channel.
• FR adjusts the high frequency output level of the front
right channel.
• C adjusts the high frequency output level of the center
channel.
• SL adjusts the high frequency output level of the
surround left channel.
• SR adjusts the high frequency output level of the
surround right channel.
y
We recommend that you use the initial setting (–0.5 m) for the
center channel.
d)FOCAL LENGTH
5 beam
. Front L;;;;;;+1.5m
Front R;;;;;;+1.5m
Center;;;;;;;-0.5m
Surround L;;;+2.3m
Surround R;;;+2.3m
p
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
English
65 En
MANUAL SETUP
■ IMAGE LOCATION (Image location)
OFF
C
p
L
1)SOUND MENU
. A)TONE CONTROL
B)SUBWOOFER SET
C)MUTE LEVEL
D)AUDIO DELAY
E)ROOM EQ
F)DD/DTS Dynamic Range
[ ]/[ ]:Up/Down
[ENTER]:Enter
■ TONE CONTROL (Tone control)
You can adjust the tonal quality of the sound beams.
)ON
R
LEFT;;;;;;;;;;;0%
RIGHT;;;;;;;;;;0%
p
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
.
A)TONE CONTROLTREBLE;;;;;0dB
BASS;;;;;;;0dB
p
+
-----+
------
p
.
Use to manually adjust various parameters related to the
sound output.
SET MENU → MANUAL SETUP → SOUND MENU
p
C)IMAGE LOCATION
SOUND MENU
p
Use to adjust the direction from which the front left and
right channel sound is heard so that the each sound can be
heard closer to the center channel.
Use this feature to redirect audio signals if the sound
coming from the front left and right seems unnatural, such
as when your listening position is not the center of your
listening room.
You can only adjust this parameter when 3 beam or 5
beam is selected as the beam mode (see page 42).
Choices: ON, OFF
Setting range: 0% to 95%
Initial setting: 0%
LEFT (Left)
Adjusts audio signals towards the left.
The higher the percentage, the louder the output from the
center.
Without adjustment
With the front left
channel adjusted
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
TREBLE (Treble)
Use to adjust the high frequency response.
Choices: –12 dB to +12 dB
Initial setting: 0 dB
BASS (Bass)
Use to adjust the low frequency response.
Choices: –12 dB to +12 dB
Initial setting: 0 dB
RIGHT (Right)
Adjusts audio signals towards the right.
The higher the percentage, the louder the output from the
center.
Without adjustment
66 En
With the front right
channel adjusted
01EN_YSP-1100_UAB_EN.book Page 67 Friday, February 29, 2008 11:35 AM
MANUAL SETUP
■ SUBWOOFER SET (Subwoofer set)
Use to manually adjust various subwoofer settings.
B)SUBWOOFER SET
BASS OUT;;;;;FRONT
CROSS OVER;;;100Hz
LFE LEVEL;;;;;;0dB
DISTANCE;;;;;;3.0m
p
p
.
■ MUTE LEVEL (Muting level)
Use to adjust how much the mute function reduces the
volume level.
Choices: MUTE, –20 dB
• Select MUTE to completely halt all sound output.
• Select –20 dB to reduce the current volume level by
20 dB.
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
C)MUTE LEVEL
pMUTE
Use to delay the sound output and synchronize it with the
video image. This may be necessary when using certain
LCD monitors or projectors.
Choices: 0 to 160 msec
D)AUDIO DELAY
AUDIO DELAY;;;;;0msec
p
[ ]/[ ]:Select
[ENTER]:Return
■ ROOM EQ (Room equalizer)
Use to change the tonal qualities of your listening room
when the unit is mounted on the wall.
Choices: MOUNTING (Mount type),
REFLECTING (Reflectivity type)
E)ROOM EQ
. MOUNTING;;;;;SHELF
REFLECTING;;;NORMAL
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
p
DISTANCE (Distance)
Select to adjust the distance of the subwoofer from the
listening position.
Choices: 0.3 to 15.0 m
Initial setting: 3.0 m
■ AUDIO DELAY (Audio delay)
ADVANCED
OPERATION
LFE LEVEL (Low-frequency effect level)
Select to adjust the output level of the LFE (low-frequency
effect) channel according to the capacity of your
subwoofer. The LFE channel carries low-frequency
special effects which are only added to certain scenes.
This setting is effective only when this unit decodes Dolby
Digital or DTS signals.
Choices: –20 to 0 dB
[ ]/[ ]:Select
[ENTER]:Return
p
CROSS OVER (Cross over)
When BASS OUT is set to SWFR, you can use this
feature to select a cross-over (cut-off) frequency for all
low-frequency signals. All frequencies below the selected
frequency will be sent to the subwoofer speaker position.
Choices: 80Hz, 100Hz, 120Hz
p
-20dB
p
BASS OUT (Bass out)
Low-frequency (bass) signals can be directed to the
subwoofer or the front left and right channels. This setting
also determines the routing of LFE (low-frequency effect)
signals found in Dolby Digital or DTS sources.
Choices: SWFR (subwoofer), FRONT
• Select SWFR if you connect a subwoofer. LFE and
low-frequency signals from other channels are directed
to the subwoofer.
• Select FRONT if you do not use a subwoofer. LFE and
low-frequency signals from other channels are directed
to the front left and right channels.
MOUNTING (Mount type)
Use to enhance medium to low range sounds.
Choices: WALL (Wall mount), SHELF (Shelf mount)
• Select WALL if this unit is mounted on the wall in your
listening room.
• Select SHELF if this unit is mounted on the shelf in
your listening room.
67 En
Black process 45.0° 240.0 LPI
English
REFLECTING (Reflectivity type)
Use to select the reflectivity of your listening room.
Choices: NORMAL (Normal), HI ECHO (High echo)
• Select NORMAL if your listening room has a normal
reflectivity.
• Select HI ECHO if your listening room has highly
reflective surfaces such as concrete walls.
01EN_YSP-1100_UAB_EN.book Page 68 Wednesday, August 30, 2006 1:46 PM
MANUAL SETUP
■ DD/DTS Dynamic Range
(Dynamic range of Dolby Digital and
DTS signals)
Use to manually adjust various parameters related to the
audio and video input.
SET MENU → MANUAL SETUP → INPUT MENU
3 INPUT MENU
. A)INPUT
B)INPUT
C)INPUT
D)INPUT
ASSIGNMENT
MODE
TRIM
RENAME
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
Use to select the amount of dynamic range compression.
This setting is effective only when the unit is decoding
Dolby Digital and DTS signals. Dynamic range is the
difference between the smallest sound that can be heard
above the noise of the equipment and the biggest sound
that can be heard without distortion.
Choices: MIN (minimum), STD (standard),
MAX (maximum)
INPUT MENU
F)DD/DTS Dynamic Range
p
STD
pMAX
p
MIN
[ ]/[ ]:Select
[ENTER]:Return
Select to adjust the dynamic range compression.
• Select MIN for listening to sources at low volume
levels.
• Select STD for general use.
• Select MAX for feature films.
■ INPUT ASSIGNMENT (Input assignment)
Use to assign the input jacks of this unit to other
components if the initial settings of this unit do not
correspond to your needs. By assigning other components
to the input jacks on this unit, you can display the name of
the connected component in the front panel display and
OSD, and operate the component with the input selector
button of the same name. If you connect a component to
the input jacks of this unit and do not assign it, the default
component name for that input jack is displayed in the
front panel and OSD when selected.
• Select OPTICAL IN (1) to assign components to the
TV OPTICAL IN jack of this unit.
Choices: TV, VCR
• Select OPTICAL IN (2) to assign components to the
AUX OPTICAL DIGITAL IN jack of this unit.
Choices: AUX, DVD
A)INPUTOPTICAL
ASSIGNMENT
1/4
IN
TV
TV
AUX
AUX
)
)
p
p
. (1);;;;;
(
(2);;;;;
(
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
• Select COAXIAL IN (3) to assign components to the
COAXIAL DIGITAL IN jack of this unit.
Choices: DVD, AUX
A)INPUT ASSIGNMENT
2/4
COAXIAL IN
DVD
DVD
p
)
p
. (3);;;;;
(
68 En
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
MANUAL SETUP
■ INPUT TRIM (Input trim)
Use to adjust the input level of the input source.
C)INPUT TRIM
.
TV
VCR
AUX
DVD
ANALOG;;;-3.0dB
OPTICAL;;-3.0dB
ANALOG;;;-3.0dB
COAXIAL;;-3.0dB
COAXIAL;;-3.0dB
p
p
• Select COMPONENT (1) to assign components to the
STB COMPONENT VIDEO IN jacks of this unit.
Choices: TV, VCR
• Select COMPONENT (2) to assign components to the
DVD/AUX COMPONENT VIDEO IN jacks of this
unit.
Choices: DVD, AUX
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
A)INPUTCOMPONENT
ASSIGNMENT 3/4
TV
TV
DVD
DVD
p
)
)
p
. (1);;;;;
(
(2);;;;;
(
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
• Select COMPOSITE (3) to assign components to the
DVD/AUX VIDEO IN jack of this unit.
Choices: AUX, DVD
A)INPUTCOMPOSITE
ASSIGNMENT 4/4
AUX
AUX
p
)
p
. (3);;;;;
(
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
■ INPUT MODE (Input mode)
Use to designate the input mode for the input sources
connected to the DIGITAL INPUT jacks when you turn on
the power of this unit. For information on the types of
audio signals that can be output by this unit, see “Surround
modes and recommended sources” on page 44.
Choices: AUTO, LAST
• Select TV ANALOG to adjust the level of audio and
video signals input at the TV/STB analog audio input
jacks of this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select TV OPTICAL to adjust the level of audio and
video signals input at the TV OPTICAL IN jack of this
unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select VCR ANALOG to adjust the level of audio and
video signals input at the VCR analog audio input
jacks of this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select AUX OPTICAL to adjust the level of audio and
video signals input at the AUX OPTICAL IN jack of
this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select DVD COAXIAL to adjust the level of audio and
video signals input at the COAXIAL IN jack of this
unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
pAUTO
LAST
p
p
ADVANCED
OPERATION
B)INPUT MODE
[ ]/[ ]:Select
[ENTER]:Return
• Select AUTO to allow this unit to automatically detect
the type of input signal and select the appropriate input
mode.
• Select LAST to set this unit to automatically select the
last input mode used for that input source. If the type of
input signal is different from the setting, no sounds will
be produced.
English
69 En
MANUAL SETUP
■ INPUT RENAME (Input rename)
DISPLAY MENU
Use to change the name of the input source in the OSD
and the front panel display. Press an input selector button
(TV, STB, DVD, VCR, or AUX) to select the component
you want to change the name for and then perform the
following procedure.
Use to manually adjust various parameters related to the
display.
SET MENU → MANUAL SETUP → DISPLAY MENU
D)INPUT RENAME
4 DISPLAY MENU
DVD ->
p
1
p
p
[ ]/[ ]:Position
[ ]/[ ]:Character
[ENTER]:Return
p
[ ]/[ ]:Up/Down
[ENTER]:Enter
p
p
. A)DIMMER SET
B)OSD SET
C)UNIT SET
DVD
■ DIMMER SET (Dimmer settings)
Press / to place the _ (underbar) under
the space or the character you want to edit.
The _ (underbar) flashes.
Use to adjust the brightness of the front panel display.
A)DIMMER SET
. STANDARD DIMMER;;;;;OFF
AUTO DIMMER
;;;;;;;;;;;;;OFF
p
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
ENTER
2
Press
/
to select the desired character.
• You can use up to 8 characters for each input.
• Press
to change the character in the following
order or press
to go in the reverse order:
A to Z, a space, 0 to 9, a space, a to z, a space, #, *,
+, etc.
ENTER
3
Repeat steps 1 to 3 to rename each input.
4
Press ENTER to exit.
The new names are registered, and the display returns
to the previous screen.
ENTER
70 En
STANDARD DIMMER (Standard dimmer)
Use to adjust the brightness of the front panel display
when you operate this unit by using the control buttons on
the front panel or on the remote control.
Choices: –2, –1, OFF
AUTO DIMMER (Auto dimmer)
If no operation is performed for a specified period, the
front panel display dims. Use to adjust the brightness of
the front panel display in this case.
Choices: OFF (the same brightness as the STANDARD
DIMMER setting), –1 to –3 (based on the
STANDARD DIMMER setting), DISPLAY OFF
MANUAL SETUP
■ OSD SET (OSD settings)
Use to adjust the display position and the background
color of the OSD.
B)OSD SET
. OSD SHIFT;;;;;;;;0
OSD BACK COLOR;;;BLUE
p
p
p
p
[ ]/[ ]:Up/Down [ ]/[ ]:Sel
[ENTER]:Return
OSD SHIFT (OSD shift)
Use to adjust the vertical position of the OSD. Adjust
towards the – (minus) direction to raise the position of the
OSD, and adjust towards the + (plus) direction to lower it.
Choices: –5 to +5
Initial setting: 0
OSD BACK COLOR (OSD background color)
Use to select the background color of the OSD.
Choices: BLUE, GRAY
■ UNIT SET (Unit settings)
Use this to change the display unit of measurement.
Choices: METERS (Australia and U.K. models),
FEET (U.S.A. model)
C)UNIT SET
pMETERS
p
p
FEET
[ ]/[ ]:Select
[ENTER]:Return
• Select METERS to input distances in meters.
• Select FEET to input distances in feet.
ADVANCED
OPERATION
Note
If you change this setting, the adjusted beam settings may change.
English
71 En
ADJUSTING THE AUDIO BALANCE
ADJUSTING THE AUDIO BALANCE
You can adjust the sound beam output level of each channel by using the test tone or the audio output being played back
in each beam mode to achieve a more true-to-life surround sound experience.
3
Using the test tone
You can use the test tone feature to output a test tone from
each channel to manually balance the channel levels.
Use the test tone to set channel levels so that the volume
level of each channel is identical when heard from your
listening position.
Press
/
to select the channel you want
to adjust.
The front panel display changes as follows.
TEST FRONT L
TEST CENTER
ENTER
OFF
0
+10
CH LEVEL
TEST FRONT R
MENU
TEST SUR.R
TV/AV
ENTER
YSP
RETURN
TEST
TEST SUR.L
TEST SWFR
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TEST SWFR is only available when a subwoofer is connected to
this unit and SWFR is selected for BASS OUT in SOUND
MENU (see page 67).
TV/AV
YSP
2
Note
Press TEST on the remote control.
TEST FRONT L appears in the front panel display
and a test tone is output from the front left channel.
4
Press
/
to adjust channel volumes.
TEST
ENTER
Control range: –10 dB to +10 dB
VOL
TEST FRONT L
72 En
ADJUSTING THE AUDIO BALANCE
5
Press TEST when you have completed all
your adjustments.
TEST
Using the audio output being
player back
You can also manually adjust the channel levels while
playing back an input source such as a DVD.
OFF
0
Notes
• All the channel levels cannot be adjusted when the stereo
playback or my beam is selected as the beam mode (see
pages 47 and 48).
• FRONT L/R cannot be adjusted when the stereo plus 3 beam is
selected as the beam mode (see page 43).
• FRONT L/R are automatically adjusted depending on the
settings of the other channels when the stereo plus 3 beam or
stereo playback is selected as the beam mode (see pages 43 and
47).
+10
CH LEVEL
MENU
TV/AV
ENTER
YSP
RETURN
TEST
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
y
If the level of a particular channel cannot be adjusted, – –dB
appears in the front panel display.
TV/AV
YSP
2
Press CH LEVEL repeatedly (or press
CH LEVEL and then
/
) to select the
channel you want to adjust.
The front panel display changes as follows.
CH LEVEL
or
CH LEVEL
ENTER
ADVANCED
OPERATION
FRONT L +1.0dB
CENTER
-2.5dB
FRONT R +1.0dB
SUR.R
+2.0dB
SUR.L
+2.0dB
--dB
73 En
English
SWFR
ADJUSTING THE AUDIO BALANCE
Note
SWFR is only available when a subwoofer is connected to this
unit and SWFR is selected for BASS OUT in SOUND MENU
(see page 66).
3
Press
/
to adjust channel volumes.
ENTER
Control range: –10 dB to +10 dB
4
Wait for a few seconds without operating this
unit when you have completed your
adjustment.
Notes
• All the channel levels cannot be adjusted when the stereo
playback is selected as the beam mode (see page 47).
• FRONT L/R cannot be adjusted when the stereo plus 3 is
selected as the beam mode (see page 41).
• Only CENTER can be adjusted when the my beam is selected
as the beam mode (see page 48).
• FRONT L/R are automatically adjusted depending on the
settings of the other channels when the stereo plus 3 beam or
stereo playback is selected as the beam mode (see pages 43 and
47).
y
If the level of a particular channel cannot be adjusted, – –dB
appears in the front panel display.
74 En
SELECTING THE INPUT MODE
SELECTING THE INPUT MODE
You can select the type of audio input signals of the selected input source according to your preference or the conditions
of the input source.
y
We recommend setting the input mode to AUTO in most cases.
Notes
STB
• The input mode of VCR is fixed to ANALOG. However, if the
TV OPTICAL IN jack of this unit is assigned to VCR, AUTO,
DTS and ANALOG become available as the input mode of
VCR (see page 68).
• ANALOG is not available as the input mode of DVD and AUX.
POWER POWER
STANDBY/ON
VCR
INPUT1
AV
TV
DVD
AUX
TV
INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
1
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
• DTS
Selects only digital signals encoded in DTS.
Compared to AUTO, this input mode provides greater
stability while playing back CDs or LDs encoded in DTS.
TV/AV
YSP
2
Press one of the input selector buttons on
the remote control to select the desired input
source.
STB
VCR
DVD
• ANALOG
Selects only analog signals.
Even when both digital and analog signals are input
simultaneously, only analog signals are selected.
y
AUX
You can adjust the default input mode to be selected when the
power of this unit is turned on (see page 69).
TV
ADVANCED
OPERATION
3
• AUTO
Automatically selects audio input signals in the following
priority order:
1) Dolby Digital or DTS
2) PCM
3) Analog
Use this input mode in most cases.
Press INPUTMODE on the remote control
repeatedly to toggle between input modes.
INPUTMODE
TV AUTO
DVD AUTO
AUX AUTO
TV DTS
DVD DTS
AUX DTS
TV ANALOG
When DVD is
selected as the
input source
When AUX is
selected as the
input source
English
When TV or STB
is selected as
the input source
75 En
ADJUSTING SYSTEM PARAMETERS
ADJUSTING SYSTEM PARAMETERS
This unit has additional menus that are displayed in the front panel display. These menus offer additional operations to
adjust and customize the way this unit operates.
Using the system parameters
3
Release INPUT on the front panel.
Follow the procedure below to enter the system
parameters.
INPUT
Setting the MEMORY PROTECT
You can protect the settings you saved in the system
memory of this unit from being accidentally erased or
unwantedly changed.
INPUT
VOLUME
+
STANDBY/ON
CH LEVEL
MENU
1
Repeat steps 1 to 3 in “Using the system
parameters” on this page.
2
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
ENTER
YSP
RETURN
TEST
TV/AV
YSP
1
Press STANDBY/ON on the front panel to
turn off the power of this unit.
STANDBY/ON
3
Confirm that MEMORY PROTECT is shown in
the front panel display and then press
ENTER.
VOL
2
MEMORY PROTECT
Press and hold INPUT on the front panel and
then press STANDBY/ON on the front panel
to turn on the power of this unit.
MEMORY PROTECT is shown in the front panel
display.
STANDBY/ON
ENTER
INPUT
VOL
MEMORY PROTECT
76 En
ADJUSTING SYSTEM PARAMETERS
4
Press / to switch between PROTECT: ON
and PROTECT: OFF.
3
Press
/
on the remote control so that
MAX VOLUME SET is shown in the front
panel display.
ENTER
ENTER
VOL
PROTECT: ON
VOL
MAX VOLUME SET
VOL
PROTECT: OFF
4
Press ENTER.
• Select PROTECT: ON to activate the protection
feature.
• Select PROTECT: OFF to deactivate the protection
feature.
5
Press STANDBY/ON on the front panel to set
this unit to the standby mode.
ENTER
5
STANDBY/ON
The new setting will be activated when you turn on
the power of this unit next time.
Press
level.
/
to adjust the maximum volume
ENTER
You can set the maximum volume level so that this unit
will not output sound beyond the limited volume level.
1
2
Repeat steps 1 to 3 in “Using the system
parameters” on page 76.
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
YSP
ADVANCED
OPERATION
Setting the MAX VOLUME
Control range: MAX, 99 to 01, MIN
Control step: 1
6
Press STANDBY/ON on the front panel to set
this unit to the standby mode.
STANDBY/ON
The new setting for the maximum volume level will
be activated when you turn on the power of this unit
next time.
English
77 En
ADJUSTING SYSTEM PARAMETERS
Setting the TURN ON VOLUME
6
You can set the initial volume level when the power of this
unit is turned on.
1
2
Press STANDBY/ON on the front panel to set
this unit to the standby mode.
STANDBY/ON
Repeat steps 1 to 3 in “Using the system
parameters” on page 76.
The new setting for the maximum volume level will
be activated when you turn on the power of this unit
next time.
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
Setting the DEMO MODE
TV/AV
You can test the beam output from this unit to experience
the sound beam.
YSP
3
y
Press
/
on the remote control so that
TURN ON VOLUME is shown in the front
panel display.
You can also perform this function simply by pressing INPUT on
the front panel. A sound beam is output from this unit when you
press and hold INPUT for more than 2 seconds. The sound beam
shuttles between left and right twice, and then stops.
1
Repeat steps 1 to 3 in “Using the system
parameters” on page 76.
2
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
ENTER
TV/AV
YSP
VOL
TURN ON VOLUME
4
Press ENTER.
ENTER
5
Press
/
3
Press
/
on the remote control so that
DEMO MODE is shown in the front panel
display.
ENTER
to adjust the initial volume level.
VOL
DEMO MODE
ENTER
Control range: MAX, 99 to 01, OFF
Control step: 1
78 En
ADJUSTING SYSTEM PARAMETERS
4
Press / to switch between DEMO: ON
and DEMO: OFF.
Setting the FACTORY PRESET
You can reset all of the parameters of this unit to the
factory presets. This procedure completely resets ALL the
parameters in SET MENU.
Note
ENTER
After performing the following procedure you must run the
AUTO SETUP again to match your surround sound environment.
VOL
DEMO: ON
1
Repeat steps 1 to 3 in “Using the system
parameters” on page 76.
2
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
TV/AV
YSP
VOL
DEMO: OFF
3
• Select DEMO: ON to activate the demo mode.
• Select DEMO: OFF to deactivate the demo mode.
5
Press
/
on the remote control so that
FACTORY PRESET is shown in the front
panel display.
Press STANDBY/ON on the front panel to set
this unit to the standby mode.
ENTER
STANDBY/ON
The new setting will be activated when you turn on
the power of this unit next time.
Press ENTER to test the sound beam.
The sound beam being output shuttles between left
and right. Press ENTER again to stop shuttling.
VOL
4
ADVANCED
OPERATION
FACTORY PRESET
Press ENTER.
ENTER
English
79 En
ADJUSTING SYSTEM PARAMETERS
5
Press / to switch between PRESET:
RESET and PRESET: CANCEL.
ENTER
VOL
PRESET: RESET
VOL
PRESET: CANCEL
• Select PRESET: RESET to reset all of the current
settings.
• Select PRESET: CANCEL to cancel the resetting
procedure.
6
Press STANDBY/ON on the front panel to set
this unit to the standby mode.
STANDBY/ON
The new setting will be activated when you turn on
the power of this unit next time.
80 En
REMOTE CONTROL FEATURES
REMOTE CONTROL FEATURES
In addition to controlling this unit, the remote control can also operate other A/V components made by YAMAHA and
other manufacturers. To control other components, you must set up the remote control with the appropriate remote
control codes and set the operation mode selector to TV/AV to change the control area.
Note
Depending on the external A/V component you are using, you may not be able to operate the component with the remote control, even
if a remote control code is set. In this case, operate the component using the supplied remote control.
Setting remote control codes
2
You can control other components by setting the
appropriate remote control codes. Codes can be set up for
each input area (TV, STB, DVD, VCR and AUX).
For a complete list of available remote control codes, refer
to “LIST OF REMOTE CONTROL CODES” at the end of
this manual.
Press the numeric buttons to enter the
remote control code while holding down
CODE SET.
Setting example: YAMAHA DVD input area
SURROUND
6
TV MUTE
While holding
down, press
STB
VCR
DVD
INPUT1
SPORTS
9
CODE SET
AUX
TV
INPUT2 MACRO
SPORTS
9
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
3
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
OFF
0
+10
CH LEVEL
MENU
TV/AV
ENTER
YSP
RETURN
TEST
VOLUME
CH
TV VOL
Refer to “Controlling other components” on
page 82 to operate the external component
using the remote control.
If the external component functions correctly, the
remote control code setup was successful.
If the external component does not function correctly,
the remote control code may be incorrect. Confirm
that the remote control code is correct (see “LIST OF
REMOTE CONTROL CODES” at the end of this
manual) and start over from step 1.
MUTE
TV INPUT
If the manufacturer of your component has more than one code,
try each of them until you find the correct one.
TV MUTE
CODE SET
1
Press and hold CODE SET on the remote
control and then press one of the input
selector buttons to select the input source
you want to set a remote control code for.
The transmission indicator flashes twice and then
remains lit.
Proceed to step 2 while holding down CODE SET.
STB
TV MUTE
VCR
DVD
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries and reset the remote control codes.
When changing the batteries, be careful not to press
any of the buttons on the remote control. Doing so will
clear the contents of the memory.
AUX
English
While holding
down, press
ADVANCED
OPERATION
Note
TV
CODE SET
81 En
REMOTE CONTROL FEATURES
Controlling other components
■ Operating your TV
■ Operating your DVD player
Set the operation mode selector to TV/AV and
then press TV to select TV as the input source.
The control area of the remote control changes to the TV
operation mode.
Set the operation mode selector to TV/AV and then
press DVD to select DVD as the input source.
The control area of the remote control changes to the DVD
operation mode.
TV
TV/AV
DVD
TV/AV
YSP
YSP
POWER POWER
STANDBY/ON
AV
POWER POWER
STANDBY/ON
TV
AV
TV
1
STB
VCR
DVD
INPUT1
AUX
TV
INPUT2 MACRO
1
2
STB
AUX
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
5BEAM
ST+3BEAM
3BEAM
1
2
3
1
2
3
STEREO
MY BEAM SURROUND
2
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
0
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
8
9
OFF
+10
CH LEVEL
0
MENU
4
ENTER
YSP
RETURN
TEST
CH
+10
CH LEVEL
TV/AV
VOLUME
STEREO
7
OFF
MENU
3
TV/AV
ENTER
YSP
RETURN
TEST
TV VOL
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
5
5
4
MUTE
6
DVD
TV
INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
3
VCR
INPUT1
TV
TV INPUT
TV MUTE
CODE SET
7
CODE SET
6
1 TV POWER
Turns on or off the power of your TV.
1 AV POWER
Turns on or off the power of your DVD player.
2 TV INPUT1/2
Selects the input source of the TV.
2 Numeric buttons
Use to enter numeric digits.
3 Numeric buttons
Selects a TV channel for playback.
3 MENU
Displays the DVD menu.
4 CH +/–
Switches between the available TV channels.
5 TV VOL +/–
Adjusts the audio output level of the TV.
6 TV MUTE
Temporarily mutes audio output from the TV.
7 TV INPUT
Switches the input source for the TV.
82 En
4 Cursor buttons
/
/
Use to select DVD menu items.
/
, ENTER
5 RETURN
Use to return to the previous DVD menu screen or exit the
DVD menu.
6 Operation buttons for DVD and VCR players
Use to perform DVD player operations, such as play and
stop.
REMOTE CONTROL FEATURES
■ Operating your VCR
■ Operating your STB
(CATV/Satellite tuner)
Set the operation mode selector to TV/AV and
then press VCR to select VCR as the input
source.
The control area of the remote control changes to the VCR
operation mode.
Set the operation mode selector to TV/AV and
then press STB to select STB as the input
source.
The control area of the remote control changes to the STB
operation mode.
VCR
TV/AV
STB
TV/AV
YSP
YSP
POWER POWER
STANDBY/ON
AV
POWER POWER
STANDBY/ON
TV
AV
TV
1
STB
VCR
DVD
INPUT1
1
AUX
STB
TV
INPUT2 MACRO
VCR
DVD
INPUT1
TV
AUX
TV
INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
5BEAM
ST+3BEAM
3BEAM
1
2
3
1
2
3
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
2
OFF
0
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
OFF
+10
CH LEVEL
0
MENU
+10
CH LEVEL
MENU
TV/AV
TV/AV
ENTER
ENTER
YSP
YSP
RETURN
TEST
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
2
RETURN
TEST
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
3
CODE SET
CODE SET
3
1 AV POWER
Turns on or off the power of your STB.
2 CH +/–
Switches between the available VCR channels.
2 Numeric buttons
Use to enter the numeric digits.
3 Operation buttons for DVD and VCR
Use to perform VCR operations, such as play and stop.
3 CH +/–
Switches between the available STB channels.
ADVANCED
OPERATION
1 AV POWER
Turns on or off the power of your VCR.
English
83 En
REMOTE CONTROL FEATURES
■ Setting macros for the TV with the
tuning capability
Using the TV macro
The TV macro feature makes it possible to perform a
series of operations with the press of a single button. For
example, when you want to play a DVD, you would
normally turn on the component, select DVD as the input
source and press the play button to start playback. The TV
macro feature lets you perform all of these operations
simply by pressing the DVD macro button.
Notes
1
Press and hold CODE SET on the remote
control and then press one of the input
selector buttons to select the input source
you want to set macros for.
Proceed to step 2 while holding down CODE SET.
TV MUTE
• Be sure to set up a remote control code for your TV before
setting macros.
• The ways to set macros differ if your TV does not have the
tuning capability.
• If you press any control buttons on the remote control other than
the ones used to set macros while setting macros, the setting
procedure is automatically canceled.
• If it takes more than 10 seconds in steps 2 and 3, the setting
procedure is automatically canceled. In this case, repeat from
step 1.
STB
While holding
down, press
CODE SET
2
VCR
AUX
DVD
TV
Press MACRO on the remote control while
holding down CODE SET.
TV MUTE
While holding
down, press
MACRO
CODE SET
POWER POWER
STANDBY/ON
STB
VCR
INPUT1
AV
TV
DVD
AUX
3
Press CH +/– or the numeric buttons to select
the TV channel.
Check that the TV screen changes to the tuner screen.
TV
INPUT2 MACRO
TV
CH
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
or
MY BEAM SURROUND
5BEAM
ST+3BEAM
1
2
3
STEREO
MY BEAM
SURROUND
3BEAM
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
4
5
6
MUSIC
MOVIE
SPORTS
OFF
7
8
9
0
+10
OFF
0
+10
CH LEVEL
MENU
4
TV/AV
ENTER
YSP
Press TV INPUT on the remote control
repeatedly so that the screen changes to the
display of the input source selected in step 1.
RETURN
TEST
TV INPUT
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
CODE SET
5
Press ENTER on the remote control to
confirm the macro setting.
ENTER
84 En
REMOTE CONTROL FEATURES
■ Setting macros for the TV without the
tuning capability
■ Operating macros
1
1
Press and hold CODE SET on the remote
control and then press one of the input
selector buttons to select the input source
you want to set macros for.
Proceed to step 2 while holding down CODE SET.
TV MUTE
STB
DVD
AUX
TV/AV
YSP
2
While holding
down, press
TV
CODE SET
2
VCR
Set the operation mode selector to YSP to
switch to the operation mode of this unit.
Press and hold one of the input selector
buttons for approximately 2 seconds to
select the input source you want to operate
macros for.
The TV input changes at the same time the input
mode changes.
Press MACRO on the remote control while
holding down CODE SET.
TV MUTE
While holding
down, press
STB
MACRO
VCR
AUX
DVD
TV
CODE SET
■ Canceling the macros
3
Press INPUT1 on the remote control.
1
INPUT1
4
Press CH +/– or TV INPUT on the remote
control repeatedly so that the screen
changes to the display of the input source
selected in step 1.
Press and hold CODE SET on the remote
control and then press one of the input
selector buttons to select the input source
you want to cancel the macros for.
Proceed to step 2 while holding down CODE SET.
TV MUTE
While holding
down, press
STB
VCR
DVD
AUX
TV
CODE SET
CH
2
Press MACRO on the remote control while
holding down CODE SET.
TV MUTE
While holding
down, press
MACRO
ADVANCED
OPERATION
TV INPUT
or
CODE SET
5
Press ENTER on the remote control to
confirm the setting.
3
Press ENTER on the remote control to cancel
the macros.
ENTER
ENTER
English
85 En
TROUBLESHOOTING
TROUBLESHOOTING
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, set this unit to the standby mode, disconnect the power supply cable and contact
the nearest authorized YAMAHA dealer or service center.
■ General
See
page
Problem
Cause
Remedy
This unit fails to turn on when
STANDBY/ON is pressed, or enters
the standby mode soon after the
power has been turned on.
The power supply cable is not firmly
connected to the AC wall outlet or to the
AC inlet on the rear panel of this unit.
Connect the power supply cable firmly to
the AC wall outlet or to the AC inlet on
the rear panel of this unit.
23
This unit has been exposed to a strong
external electric shock (such as lightning
and strong static electricity).
Set this unit to the standby mode,
disconnect the power supply cable, plug
it back in after 30 seconds, then use it
normally.
—
This unit suddenly enters the
standby mode.
The internal temperature becomes too
high and the overheat protection circuitry
has been activated.
Wait about 1 hour for this unit to cool
down and then turn it back on.
—
The sleep timer has turned the unit off.
Turn on the power, and play the source
again.
—
Incorrect input or output cable
connections.
Connect the cables properly. If the
problem persists, the cables may be
defective.
15
No appropriate input source has been
selected.
Select an appropriate input source with
INPUT or the input selector buttons.
39
The volume is turned down.
Turn up the volume.
41
The sound is muted.
Press MUTE or VOLUME +/– on the
remote control to resume audio output
and then adjust the volume level.
41
Signals this unit cannot reproduce (such
as PCM signals with more than 96 kHz
of sampling frequency) are being
received froma source component.
Play a source whose signals can be
reproduced by this unit.
—
Change the system settings of the source
component.
—
The sleep timer has turned the unit off.
Turn on the power, and play the source
again.
—
The sound is muted.
Press MUTE or VOLUME +/– on the
remote control to resume audio output
and then adjust the volume level.
41
No sound from the effect
channels.
You are playing back the source or
program in the stereo mode or my beam
mode.
Press one of the beam mode buttons on
the remote control to select a multichannel playback mode and then try to
play back the source or program once
more.
42
No sound from the center channel.
The output level of the center channel is
set to minimum.
Raise the level of the center channel.
72
No sound from the surround
channels.
The output level of the surround
channels is set to minimum.
Raise the output level of the surround
channels.
72
No sound from the subwoofer.
BASS OUT in SUBWOOFER SET is set
to FRONT.
Select SWFR.
67
No sound.
The sound suddenly goes off.
The source does not contain low bass
signals.
86 En
TROUBLESHOOTING
Cause
Distorted or too little bass sound.
CROSS OVER in SUBWOOFER SET is
set incorrectly.
Set CROSS OVER correctly.
One of the night listening modes is
currently selected.
Turn off the night listening modes.
TruBass is currently turned on.
Turn off TruBass.
57
The volume level of the subwoofer is too
high.
Turn down the volume level of the
subwoofer.
—
The listening room is not a regular shape.
Install this unit in a square or rectangular
shaped room.
—
There is no wall in the path of the sound
beam.
Try placing a flat object, such as a board,
in the path of the sound beam.
—
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following
the operating instructions for your
component.
—
The input mode is set to ANALOG.
Set the input mode to AUTO.
75
The protection circuitry was in operation
because a source with strong bass
elements was played back.
Turn down the volume level.
41
Select SWFR for BASS OUT.
67
Connect a subwoofer and adjust settings
for SUBWOOFER SET.
67
Too much bass sound.
Surround sound effects are
insubstantial.
Dolby Digital or DTS sources
cannot be played. (Dolby Digital or
DTS indicator does not light up in
the front panel display.)
There is noise interference when a
subwoofer is not connected to this
unit.
Remedy
See
page
Problem
67
55
Set CROSS OVER correctly.
67
On-screen display does not
appear.
The VIDEO OUT (composite) jack of
this unit is not connected to the video
input jacks of your TV.
Connect the VIDEO OUT (composite)
jack of this unit to the video input jacks
of your TV. The OSD is not output at the
COMPONENT VIDEO OUT jacks.
16
The video pin cable is not connected
properly.
Connect the cable properly.
16
No picture is displayed for
external components, such as a
DVD player.
The video pin cable is not connected
properly.
Connect the cable properly.
17
This unit does not operate
properly.
The internal microcomputer has been
frozen by an external electric shock
(such as lightning or excessive static
electricity) or by a power supply with
low voltage.
Disconnect the AC power supply cable
from the outlet and then plug it in again
after about 30 seconds.
—
There is noise interference from
digital or high-frequency
equipment.
This unit is too close to the digital or
high-frequency equipment.
Move this unit further away from such
equipment.
—
This unit does not output effect
sounds properly.
The original source includes surround
effects.
Disable surround effect settings on this
unit.
—
My beam auto-adjust function
does not work.
The listening room is too noisy.
Keep the listening room as quiet as
possible.
—
Try manual adjustment.
49
The sound reflectivity of the listening
room is too much.
Set REFLECTING to HI ECHO.
67
The remote control may be operated
outside of the remote control operation
range.
The remote control will function within a
maximum range of 6 m and no more than
30 degrees off-axis from the front panel.
24
87 En
English
CROSS OVER in SUBWOOFER SET is
set incorrectly.
ADDITIONAL
INFORMATION
Low frequency sounds are
distorted.
TROUBLESHOOTING
■ Remote control
Problem
The remote control does not work
and/or function properly.
Cause
Remedy
See
page
Wrong distance or angle.
The remote control will function within a
maximum range of 6 m and no more than
30 degrees off-axis from the front panel.
24
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
24
The external component you want to
operate is not selected as the input
source.
Press INPUT on the front panel or the
input selector buttons on the remote
control to select the external component
you want to operate.
39
The remote control code was not
correctly set.
Set the remote control code correctly or
try another code for the same
manufacturer using the “LIST OF
REMOTE CONTROL CODES” at the
end of this manual.
81
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
Use the remote control supplied with the
external component.
—
The cursor buttons do not work
during SET MENU operation.
The operation mode selector was
unwantedly set to TV/AV.
Set the operation mode selector to YSP.
—
You cannot use the my beam autoadjust function.
Wrong distance or angle.
The remote control will function within a
maximum range of 6 m and no more than
30 degrees off-axis from the front panel.
24
You cannot operate external
components with this unit’s
remote control.
88 En
GLOSSARY
GLOSSARY
Audio formats
■ Dolby Digital
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (left, center, and right), and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (low frequency effect), the system has
a total of 5.1-channels (LFE is counted as 0.1 channel). By
using 2-channel stereo for the surround channels, more
accurate moving sound effects and surround sound
environment are possible than with Dolby Surround. The
wide dynamic range (from maximum to minimum
volume) reproduced by the 5 full-range channels and the
precise sound orientation generated using digital sound
processing provide listeners with previously unheard of
excitement and realism.
With this unit, any sound environment from monaural up
to a 5.1-channel configuration can be freely selected for
your enjoyment.
■ Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround software.
This new technology enables a discrete 5-channel
playback with 2 front left and right channels, 1 center
channel, and 2 surround left and right channels (instead of
only 1 surround channel for conventional Pro Logic
technology). Music and Game modes are also available for
2-channel sources in addition to the Movie mode.
■ Dolby Surround
DTS digital surround was developed to replace the analog
soundtracks of movies with a 6-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. Digital Theater Systems Inc.
has developed a home theater system so that you can enjoy
the depth of sound and natural spatial representation of
DTS digital surround in your home. This system produces
practically distortion-free 6-channel sound (technically, a
left, right and center channels, 2 surround channels, plus
an LFE 0.1 channel as a subwoofer, for a total of 5.1channels). The unit incorporates a DTS-ES decoder that
enables 6.1-channel reproduction by adding the surround
back channel to existing 5.1-channel format.
■ DTS Neo:6
Neo:6 decodes the conventional 2-channel sources for 6
channel playback by the specific decoder. It enables
playback with the full-range channels with higher
separation just like digital discrete signal playback. Two
modes are available; Music mode for playing music
sources and Cinema mode for movies.
■ PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for pulse code
modulation, the analog signal is encoded as pulses and
then modulated for recording.
Audio information
■ LFE 0.1 channel
This channel is for the reproduction of low bass signals.
The frequency range for this channel is 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low frequency range compared to the full-range
reproduced by the other 5/6 channels in Dolby Digital or
DTS 5.1/6.1-channel systems.
ADDITIONAL
INFORMATION
Dolby Surround uses a 4 channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range.
Dolby Surround is widely used with nearly all video tapes
and laser discs, and in many TV and cable broadcasts as
well. The Dolby Pro Logic decoder built into this unit
employs a digital signal processing system that
automatically stabilizes the volume on each channel to
enhance moving sound effects and directionality.
■ DTS (Digital Theater Systems)
Digital Surround
English
89 En
INDEX
INDEX
A
AUTO SETUP (IntelliBeam) ......................................... 29
B
Beam mode......................................................... 42, 47, 48
C
Cable clamp .................................................................... 15
Cardboard microphone stand.......................................... 31
D
Dolby Digital .................................................................. 44
Dolby Pro Logic ............................................................. 44
Dolby Pro Logic II.......................................................... 44
DTS ................................................................................ 44
DTS Neo: 6..................................................................... 44
Dynamic range................................................................ 68
F
Front panel display ........................................................... 7
L
LFE 0.1 channel.............................................................. 89
M
MANUAL SETUP ......................................................... 60
MEMORY ................................................................ 36, 37
My beam......................................................................... 48
90 En
O
On-screen display (OSD)................................................ 26
Optimizer microphone .................................................... 30
P
PCM ................................................................................ 89
Power supply cable ......................................................... 23
R
Remote control...................................................... 9, 24, 25
Remote control code ....................................................... 81
S
SET MENU .................................................................... 26
Sleep timer ...................................................................... 58
Sound field program ....................................................... 50
Surround mode................................................................ 44
T
Test tone.......................................................................... 72
TruBass ........................................................................... 57
TV macro ........................................................................ 84
V
Volume mode .................................................................. 55
SPECIFICATIONS
SPECIFICATIONS
AMP SECTION
GENERAL
• Maximum Output Power (EIAJ)
..................................................2 W (1 kHz, 10% THD, 4 Ω) × 40
20 W (100 Hz, 10% THD, 3 Ω) × 2
• Power supply
[U.S.A. and Canada models] .............................. AC 120 V, 60 Hz
[Australia model] ............................................... AC 240 V, 50 Hz
[U.K. and Europe models] ................................. AC 230 V, 50 Hz
[China model] ..................................................... AC 220 V, 50 Hz
[Korea model] .................................................... AC 220 V, 60 Hz
[General model] ................................... AC 110–120 V, 50/60 Hz
[Asia model] .......................................... AC 220–240 V, 50/60 Hz
SPEAKER SECTION
Small dia. speakers .........4 cm cone magnetic shielding type × 40
Woofers ...........................11 cm cone magnetic shielding type × 2
• Input Jacks
AUDIO VCR, TV/STB (Analog) (1 V, 32 kΩ) ... 2 pairs (Analog)
AUDIO AUX, TV/STB (Optical) ................................. 2 (Digital)
AUDIO DVD (Coaxial) .................................................1 (Digital)
COMPOSITE VIDEO, VCR, DVD/AUX, STB .......................... 3
COMPONENT VIDEO, DVD/AUX, STB ..........................2 pairs
• Output Jacks
SUBWOOFER (1.5 V, less than 120 Hz) ............... 1 (Subwoofer)
VIDEO (1 Vp-p, 75 Ω) ............................................1 (Composite)
COMPONENT VIDEO (Y: 1 Vp-p, 75 Ω
PB/PR: 0.5 Vp-p, 75 Ω) .........................1
• Power Consumption ................................................................. 50 W
• Standby Power Consumption ...................................... 0.1 W or less
• Dimensions (W x H x D) .............................. 1030 × 194 × 118 mm
• Weight .................................................................................. 13.0 kg
*
Specifications are subject to change without notice.
• System Connector Jacks
OPTIMIZER MIC ....................................... 1 (Microphone input)
RS-232C ...........................................................1 (System control)
REMOTE IN .....................................................1 (System control)
IR-OUT .............................................................1 (System control)
ADDITIONAL
INFORMATION
English
91 En
LIST OF REMOTE CONTROL CODES
TV
ADMIRAL
292, 293, 216
AIWA
294, 276, 283, 284
AKAI
295, 296
ALBA
296
AOC
297
BELL &
HOWELL
292
BESTAR
298
BLAUPUNKT 229, 222
BLUE SKY
298
BRANDT
223
BROC SONIC 297
BUSH
296
BYD:SIGN
201, 202
CLATRONIC 298
CRAIG
224
CROSLEX
225
CURTIS MATHIS
297, 226
DAEWOO
297, 298, 224,
227, 228
DAYTRON
239
DUAL
298
DWIN
293, 281
EMERSON
297, 224, 239, 232
FURGUSON 223, 265, 266
FIRST LINE 298
FISHER
295, 233
FRABA
298
FUJITSU
289
FUNAI
277, 278
GE
293, 297, 234,
235, 236
GOODMANS 296, 298, 223
GRUNDIG
229, 238, 249
HITACHI
297, 239, 242,
243, 285, 206
ICE
296
IRRADIO
296
ITT/NOKIA
244, 245
JC PENNY
293, 297, 234, 237
JVC
296, 246, 247, 286
KENDO
298
KTV
297, 239
LG/GOLDSTAR
297, 298, 239, 237
LOEWE
298, 248
LXI
293, 297, 225,
226, 233, 298
MAGNAVOX 297, 225, 239, 298
MARANTZ
298, 210
MATSUI
295
MEDION
203, 204, 298
MEMOREX
297, 216
MITSUBISHI 299, 297, 259, 287
NAD
226, 255
NEC
297, 252, 282
NOKIA
244, 245
NOKIA OCEANIC
245
NORDMENDE 265, 266
ONWA
296
PANASONIC 234, 235, 236,
253, 288, 211
PHILCO
297, 225, 239, 298
PHILIPS
298, 225, 205
PIONEER
226, 235, 254,
255, 268
PORTLAND 297, 256
PROSCAN
293, 221
i
PROSCAN
231, 241, 251
PROTON
297, 250, 260, 270
QUASAR
234, 235
RADIO SHACK299, 293, 297
RCA
293, 297, 234,
256, 257, 258, 221
RUNCO
220, 230, 271
SABA
223, 269, 265, 266
SAMPO
281, 297, 280
SAMSUNG
297, 239, 248,
262, 275
SANYO
295, 233, 279,
272, 273, 274, 212
SCHNEIDER 296
SCOTT
297
SHARP
292, 239, 232, 213
SIEMENS
229
SIGNATURE 216
SIGNATURE 292
SONY
263, 214
SYLVANIA
297, 225, 298
SYNPHONIC 217, 218, 219
TELEFUNKUN 269, 264, 265, 266
THOMSON
223, 266
TOSHIBA
292, 226, 267, 215
VIDECH
297, 242
WARDS
297, 239, 232, 216
YAMAHA
299, 292, 242,
285, 287, 253, 206
ZENITH
216, 261, 271
DVD PLAYER
AIWA
648, 649
APEX DIGITAL
652, 653, 654
BYD:SIGN
678, 679
DAEWOO
655
DENON
623, 624, 682
FUNAI
625
HARMAN/KARDON
656, 657
HITACHI
626
JVC
627
KENWOOD
628
KLH
658
LG/GOLDSTAR
645, 663, 664
MARANTZ
699, 659
MITSUBISHI 629
ONKYO
632, 633, 634
PANASONIC 623, 635, 668,
672, 682, 683, 684
PHILIPS
699, 647, 659
PIONEER
636, 637, 638,
673, 674, 675, 685
686, 687
RCA
639
SAMSUNG
642
SHARP
643
SONY
644, 676, 677
SYLVANIA
662
SYMPHONIC 662
THOMSON
646
TOSHIBA
634, 665, 666, 667
YAMAHA
699, 622, 623,
647, 682
ZERITH
663, 664
VCR
ADMIRAL
395
AIWA
396, 397, 398, 329
AKAI
322, 323, 324
AUDIO DYNAMIC
392, 394
BELL & HOWELL
393
BLAUPUNKT 325, 326
BROC SONIC 327
BUSH
322
CANON
325, 328
CGM
396, 332
CITIZEN
396
CRAIG
396, 363
CURTHIS MATHIS
397, 328, 333
DAEWOO
328, 334, 335
DBX
392, 394
DIMENSIA
333
DYNATECH 397
EMERSON
327, 334, 396, 397
FISHER
393, 336
FUNAI
397
GE
328, 333, 387
GO VIDEO
321, 331, 341,
351, 353, 363
GOODMANS 334, 337
GRUNDIG
332, 338
HITACHI
325, 333, 349,
342, 343
INSTANT REPLAY
325, 328
ITT/NOKIA
393
JC PENNY
392, 393, 394,
328, 333, 349,
396, 363
JVC
392, 394, 344,
345, 346, 347
KENDO
396
KENWOOD
392, 394, 396
LG/GOLDSTAR
396, 388
LOEWE
396, 337
LUXOR
395
LXI
393, 396, 397,
336, 349
MAGNAVOX 325, 326, 328
MARANTZ
392, 394
MARTA
396
MATSUI
396
MEMOREX
328, 336, 396, 397
MINOLTA
333, 349
MITSUBISHI 399, 344, 348,
359, 353, 352
MTC
363, 397
MULTITECH 397, 348, 354
NEC
392, 394, 344, 383
NOKIA
393, 395
NOKIA OCEANIC
395
OKANO
323
OLYMPIC
325, 328
ORION
327
PANASONIC 325, 328, 339,
355, 378, 384,
385, 386
PENTAX
333, 349
PHILCO
325, 328, 397
PHILLIPS
325, 326, 328,
337, 356, 357
PHONOLA
337
PILOT
396
PIONEER
325
QUASAR
325, 328
RCA/PROSCAN
325, 326, 328,
333, 335, 349,
358, 363, 397
REALISTIC
393, 397, 328,
336, 359, 362,
396, 363
SAMSUNG
354, 358, 363,
364, 365, 366
SANSUI
394
SANYO
393, 336, 367
SCHNEIDER 337
SCOTT
399, 335, 336,
348, 359, 354, 358
SELECO
322
SHARP
395, 362, 382
SIEMENS
393
SIGNATURE 2000
395, 397
SONY
368, 379, 372,
373, 374, 375
SYLVANIA
397, 325, 326, 328
SYMPHONIC 397
TANDBERG 334
TANDY
397
TASHIRO
396
TATUNG
392, 394
TEAC
392, 394, 397
TECHNICS
325, 328
TEKNIKA
396
TELEFUNKUN
376, 377
THOMAS
397
THORN
393, 396
TOSHIBA
335, 389
TOTEVISION 363, 396
UNITECH
363
UNIVERSUM 396, 327, 376
VIDEOSONIC 363
W.WHOUSE 396
WARDS
395, 396, 336,
362, 397, 363
YAMAHA
399, 392, 393, 394
ZERITH
344, 361, 368,
371, 379, 396, 397
CABLE TV TUNER
ABC
739, 752, 753,
755, 758, 759, 762
GENERAL INSTRUMENT
722
HAMIN
723, 724, 725,
726, 727
HITACHI
722
JEROLD
722, 728, 729,
732, 733, 734,
735, 736, 737
MAGNAVOX 738
MOTOROLA 748
OAK
739, 742, 743
PANASONIC 744, 745, 746,
747, 783, 784
PHILLIPS
763, 764, 765,
766, 767, 768
PIONEER
748, 785, 747
RADIO SHACK749
SCIENTIFIC ATLANTA
752, 753, 754
SONY
756, 757
TOCOM
755
UNIVERSAL
VIEWSTAR
769, 772, 773,
774, 775
764, 766, 776,
777, 778, 779, 782
SATELLITE TUNER
ECHOSTAR
822
GE
837, 838, 839
GENERAL INSTRUMENT
823
HITACHI
824
HUGHES
843, 844, 845, 846
JVC
822
MAGNAVOX 825
PANASONIC 826, 829
PHILLIPS
825, 843, 844,
845, 846, 847,
848, 849
PRIMESTAR 827
PROSCAN
837, 838, 839, 842
RADIO SHACK
828
RCA
837, 838, 839, 842
SAMSUNG
852
SONY
832, 835
TOSHIBA
833, 836
UNIDEN
825
ZENITH
834
ii
YSP-1100_UAB-cv.fm Page 1 Friday, February 29, 2008 11:42 AM
UAB
YSP-1100
Digital Sound Projector
© 2006
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY. LTD. LEVEL 1, 99 QUEENSBRIDGE STREET, SOUTHBANK, VIC 3006, AUSTRALIA
Black process 45.0° 240.0 LPI
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WH82880-2
English
Connecting external components to this unit
Connect external component such as a TV or DVD player to this unit.
Connect your TV or DVD player to this unit using appropriate cables as shown below. Connecting a subwoofer enhances bass sound for listening enjoyment.
For further information on connecting other components, see pages 15 to 22 in the Owner’s Manual.
YSP-1100 QUICK REFERENCE GUIDE
DVD player
Cables used for connections
Connect cables in the following order. For the connection 2, use
either (a) or (b). If your DVD player has component video output
jacks, we suggest using the cable (b).
TV
This quick reference guide explains steps to connect a TV and a DVD player to this unit and achieve the
surround sound effects in a quick, easy manner. For detailed operation, refer to the Owner’s Manual.
Coaxial
digital
output
Video
output
Component
video
output
Optical
digital
output
Analog
audio
output
R
L
Video
input
Component
video
input
Installing this unit
1
2a
2b
3
Decide where to install this unit.
4
5
6
Install this unit where there are no objects such as furniture obstructing the path of sound beams. Otherwise, the desired surround
sound effects may not be achieved. You may install this unit in parallel with the wall or in the corner.
Install this unit in the exact center of the wall when it is
measured from the left and right corners.
An object, such as furniture
Subwoofer
Install this unit in the corner at a 40˚ to 50˚ angle from
the adjacent walls.
7
Monaural
input
An object, such as furniture
COMPONENT
COMPONENT
COMPONENT
DVD
COAXIAL
RS-232C
REMOTE IN
AUX
TV/STB
OPTICAL
DIGITAL IN
TV/STB VCR
AUDIO IN
VCR
SUBWOOFER
DVD/AUX
VIDEO IN
・Do not plug the power
supply cable into a wall
outlet until all connections
are complete.
・Unplug the power supply
cable before changing
connections, moving or
cleaning this unit.
y
If a subwoofer is connected to this unit, turn on the
power of your subwoofer and then carry out the
AUTO SETUP procedure (see the backside) or
select “SWFR” for “BASS OUT” in “SUBWOOFER
SET” (see page 67 in the Owner’s Manual).
8
This unit
40˚ to 50˚
CAUTION
1 Digital audio pin cable (supplied)
2a Video pin cable
2b Component video pin cable
3 Optical cable (supplied)
4 Audio pin cable (supplied)
5 Video pin cable (supplied)
6 Component video pin cable
(in case of a component connection)
7 Subwoofer pin cable
(in case you connect a subwoofer)
8 Power supply cable (supplied)
To the AC
outlet
STB
VIDEO OUT
Setting up the listening environment automatically
Connect the optimizer microphone to this unit.
You can automatically adjust the various channel settings that best match your listening environment using the supplied optimizer microphone. Follow the procedure below to connect the optimizer microphone to this unit and place it in a proper location.
Install this unit either above or under your TV.
Connect the optimizer microphone to the OPTIMIZER MIC jack on the left side of this unit.
Please read the following for reference. For further information on installation, see pages 11 and 13 in the Owner’s Manual.
Make sure you use the supplied fasteners to prevent an accidental fall of this unit (see page 14 in the Owner’s Manual).
When installing this unit above your TV, place it on
the top panel of a commercially available rack as
shown below.
Make sure that the top panel of the rack is wide and
stable enough to support the weight of this unit.
When installing this unit under your TV, place it in a
TV cabinet as shown below.
Make sure that the cabinet is large enough to allow
adequate ventilation space around this unit.
To enjoy better surround effects, place this unit
on the upper shelf to keep it away from the floor.
Cardboard microphone stand (supplied)
Assemble the cardboard microphone stand and place the
optimizer microphone on the top of the stand.
Optimizer microphone (supplied)
Set the optimizer microphone at your normal listening position. Use the supplied cardboard microphone stand or a tripod to place the optimizer microphone at the
same height as your ears would be when you are seated.
Place the optimizer microphone on the extended center
line of this unit and 1.8 m (6.0 ft) or more away from it.
Also, make sure place the optimizer microphone within
1 m (3.3 ft) upper or lower from the center height of this
unit.
Optimizer
microphone
Within 1 m (3.3 ft)
upper or lower
from the center
More than
1.8 m (6.0 ft)
Cardboard
microphone
stand
Printed in Malaysia
WH90290
Sofa
Center line
Optimizer
microphone
If you have set the optimizer microphone,
follow the steps on the backside to start
the AUTO SETUP procedure.
C2006
Continued
on the back
All rights reserved.
Continued
from the front
Carry out the AUTO SETUP (IntelliBeam) procedure to adjust the settings that
best match your listening environment.
Enjoying surround sound
This unit employs the YAMAHA IntelliBeam technology with the aid of the supplied optimizer microphone, allowing you to achieve highly accurate sound adjustments
that best match your listening environment. Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are
no children around in the listening room while the AUTO SETUP procedure is in progress.
Enjoy TV or DVD audio in surround sound.
1
6
Press STANDBY/ON on
the remote control.
STANDBY/ON
POWER POWER
AV
・Is the optimizer microphone firmly connected to this unit?
・Is the optimizer microphone placed in a proper loacation?
・Are there any large obstacles in between the optimizer microphone and the
walls in your listening room?
・The AUTO SETUP procedure starts in 10 seconds after pressing ENTER
on step 7. To achieve the best results possible, evacuate yourself for your
listening room until the AUTO SETUP procedure is completed.
・To cancel the AUTO SETUP procedure after it is started, press RETURN.
・The AUTO SETUP procedure takes about 3 minutes.
TV
The power of this unit turns on.
STB
VCR
DVD
AUX
TV
If a subwoofer with adjustable volume and
crossover/high cut frequency controls is
connected to this unit, set the volume
between 11 and 1 o’clock as viewed on a
conventional clockface and set the
crossover/high cut frequency to the
maximum.
CROSSOVER/
HIGH CUT
VOLUME
MIN
MAX
MIN
For instructions on your TV or DVD player, refer to the owner’s manual supplied with each component.
Before carrying out the procedure below, set the volume of this unit to 30. If necessary, adjust the volume level in
step 4.
Check the following points.
Enjoying TV in surround sound
1
Select the TV channel using
the remote control supplied
Enjoying DVDs in surround sound
1
Select the DVD video input on your
TV.
with your TV.
MAX
Subwoofer
2
2
Turn on the power of your TV.
7
CH LEVEL
TV/AV
Press ENTER to start the AUTO SETUP procedure.
ENTER
YSP
CH LEVEL
Select the appropriate video input
on your TV.
MENU
AUTO SETUP START
Will begin in 10sec
TV/AV
Please leave the room
ENTER
YSP
RETURN
TEST
3
**-------[RETURN]:Cancel
Press TV on the remote
control of this unit.
This unit switches to the TV playback mode.
4
The setup screen automatically changes during the AUTO SETUP
procedure.
If any error occurs, the corresponding error message appears on the screen.
In this case, see “Error messages for AUTO SETUP” on page 35 in the
Owner’s Manual and then follow the instructions. To start the AUTO SETUP
procedure once again, press RETURN and then carry out the procedure from
step 5.
Set the operation mode selector to YSP.
CH LEVEL
MENU
RETURN
TEST
The following screen appears on the TV and the AUTO SETUP procedure
starts in 10 seconds.
3
MENU
Set the operation mode selector to YSP .
INPUT1
3
Press DVD on the remote control of this unit,
and then start playback on the DVD player.
This unit switches to the DVD playback mode.
TV
INPUT2 MACRO
STB
VCR
TV
INPUT1
AUTO
VOL MODE SETUP INPUTMODE SLEEP
DVD
AUX
TV
INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
When the AUTO SETUP procedure is complete, the following screen
appears on the TV.
TV/AV
ENTER
YSP
TEST
RETURN
SHOW RESULT
MEASUREMENT COMPLETE
BEAM MODE :5 BEAM
SUBWOOFER:NOT APPLICABLE
* This is an example of the result screen.
4
The result may differ depending on the
environment.
If you hear sound output from your TV speakers, turn down the volume level
until you cannot hear any sound.
Use the remote control supplied with your TV.
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
5
Press and hold AUTO SETUP for more than 2
seconds.
The menu screen appears on the TV.
If the menu screen does not appear, check the video pin cable (connection
5 in the diagram on the front page) is connected properly and then press
YSP followed by MENU.
STB
VCR
DVD
AUX
TV
INPUT2 MACRO
INPUT1
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
AUTO SETUP
PREPARATION & CHECK
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
5
8
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
5BEAM
ST+3BEAM
3BEAM
1
2
3
Press VOLUME +/– on the remote control to adjust
the volume level of this unit.
Press ENTER.
The result is confirmed and the following screen appears on the TV for 2
seconds and then the menu screen disappears from the TV.
The new settings are automatically saved in the system memory.
Disconnect the optimizer microphone and keep it in a safe place.
CH LEVEL
MENU
AUTO SETUP COMPLETE
TV/AV
ENTER
YSP
TEST
Please remove the MIC from
the YSP and the listening
position.
6
Press one of the beam mode buttons on the
remote control to select the desired beam mode.
Select one of the three beam modes that best matches the current input source of
this unit.
For further information on the beam modes, see page 42 in the Owner’s Manual.
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
RETURN
To fine-tune the listening environment parameters manually or make advanced settings for
speaker positions, sound beams, etc., see “MANUAL SETUP” on page 60 in the Owner’s Manual.
Download PDF

advertising