EF.00.00.EN

EF.00.00.EN
Product Data Sheet
May 2015
EF.00.00.EN Rev. 4
EL-O-Matic F-Series
Rack and Pinion Pneumatic Actuators
„„High quality and economical actuator
„„Improve plant and operator safety
„„Reliable and flexible in process control
„„Increase serviceability
EL
Matic TM
Product Data Sheet
EL-O-Matic F-Series
EFG.01.00.EN Rev. 1
May 2015
Table of Contents
Section 1:
General
General Specifications.................................................................................................................... 4
Construction, Parts and Materials................................................................................................... 6
EL-O-Matic F Corrosion Protection System...................................................................................... 7
Assembly codes EL-O-Matic F actuators.......................................................................................... 8
Section 2:
Product Configuration Code
Product configuration code............................................................................................................ 9
Section 3:
Torque
Actuator Torque - Spring-Return (Nm).......................................................................................... 10
Actuator Torque - Spring-Return (lbf.in)........................................................................................ 12
Actuator Torque - Double-Acting (Nm)......................................................................................... 14
Actuator Torque - Double-Acting (lbf.in)...................................................................................... 15
Sizing of Rack & Pinion actuators.................................................................................................. 16
Spring cartridge placement.......................................................................................................... 18
Section 4:
Dimensions
Dimensions - Metric F12 (ISO5211).............................................................................................. 19
Dimensions - Imperial F12 (ISO5211)........................................................................................... 20
Dimensions - Metric F12 (DIN3337).............................................................................................. 21
Dimensions - Metric (ISO5211)..................................................................................................... 22
Dimensions - Metric (DIN3337).................................................................................................... 24
Dimensions - Imperial (ISO5211).................................................................................................. 26
Section 5:
Integral Options
Drive Inserts................................................................................................................................. 28
Center Plate.................................................................................................................................. 30
Visual indicator EL-O-Matic F-Series actuators.............................................................................. 31
High Temperature Execution........................................................................................................ 32
Low Temperature Execution......................................................................................................... 33
EL
Matic TM
EL-O-Matic F-Series
Product Data Sheet
May 2015
EFG.01.01.EN, Page 1 of 2, Rev. 3
General Specifications
Torque Range
Compliance to International Standards
——119 to 39498 lbf.in (13.4 to 4449 Nm)
——Valve flange:
ISO 5211/DIN3337
Pressure Range
——Solenoid flange:
VDE/VDI 3845 (NAMUR)
„„Double-Acting:
——Accessory flange:
VDE/VDI 3845 (NAMUR)
——European Directives:
ATEX, PED and Machinery Directive
——2.9 to 120 psig (0.2 to 8.3 barg)
Actuator Weight
„„Spring-Return:
——87 to 120 psig (6 to 8.3 barg), with maximum spring set
——43.5 to 120 psig (3 to 8.3 barg), reduced spring quantity
Pressure Media
——Dew point at least 10K below ambient temperature
——For sub-zero applications, take appropriate measures
——Mentioned pressure levels are "gauge pressures".
Gauge
pressure is equal to abso­lute pressure minus atmospheric
pressure.
Finish
Chromated and polyurethane powder coated
——End caps:
Chromated and polyurethane powder coated
——Pistons:
Chromated
——Pinion:
Hard Anodized
——Fasteners:
Stainless steel or Deltatone® coated
lbs
1.3
3.1
4.6
6.2
7.7
10.8
13.2
22
44
60
95
126
192
F 12
F 25
F 40
F 65
F 100
F 150
F 200
F 350
F 600
F 950
F 1600
F 2500
F 4000
——Air, dry or lubricated and inert gases
——Body:
Double-Acting
Actuator
Model
Operating Speed
Lubrication
——Castrol High Temperature grease (or equivalent)
Cycle time in seconds
Temperature Range
„„Standard:
Actuator
Model
-4 to 175°F (-20°C to 80°C)
„„Option:
F 12
F 25
F 40
F 65
F 100
F 150
F 200
F 350
F 600
F 950
F 1600
F 2500
F 4000
——Low temperature: -40°F to 176°F (-40°C to 80°C)
——High temperature:- 20°F to 248°F (-20°C to 120°C)
Angle of Rotation
„„Factory set at 90°
„„Adjustable range:
—— Size 25 to 600:
-5° to +10° and +80° to 95°
—— Size 950 to 4000:
-3° to +10° and +80° to 93°
Size 25 - 600
10°
Size 950 - 4000
-5°
10°
90°
90°
80°
80°
95°
93°
Angle of Rotation
4
(kg)
0.6
1.4
2.1
2.8
3.5
4.9
6.0
10.2
20
27
43
57
87
Spring-Return
Springset N=6
lbs
(kg)
1.5
0.7
3.5
1.6
5.1
2.3
7.3
3.3
9.5
4.3
14.6
6.6
18.3
8.3
32
14.5
62
28
86
39
146
66
194
88
291
132
-3°
Spring-Return
A-port
pressurized
0.4
0.5
0.6
0.7
0.8
1.0
1.3
1.9
3.2
4.6
6.9
9.0
15.4
Test conditions:
1.
2.
3.
4.
5.
6.
7.
Spring
Stroke
0.4
0.4
0.5
0.5
0.6
0.8
0.9
1.3
1.9
3.2
4.8
6.3
10.8
Double-Acting
A-port
B-port
pressurized pressurized
0.4
0.4
0.5
0.4
0.6
0.5
0.6
0.6
0.8
0.7
0.9
0.8
1.0
1.0
1.4
1.5
2.2
2.2
3.9
3.6
5.9
4.8
7.8
7.9
13.3
13.0
Solenoid with flow capacity:
0.6 m3/hr
Pipe diameter:
6 mm
Medium:
clean air
Supply pressure:
5.5 bar
Load:with average load
Stroke:
90°
Temperature:Room temperature
Product Data Sheet
EL-O-Matic F-Series
EFG.01.01.EN, Page 2 of 2, Rev. 3
May 2015
Actuator air volumes and consumption
Actuator
model
F0012
F0025
F0040
F0065
F0100
F0150
F0200
F0350
F0600
F0950
F1600
F2500
F4000
Actuator
model
F0012
F0025
F0040
F0065
F0100
F0150
F0200
F0350
F0600
F0950
F1600
F2500
F4000
Actuator volumes:
Maximum volume (in liters)
Central1
End cap2 Displaced3
chamber chamber
volume
0.05
0.06
0.04
0.11
0.19
0.08
0.16
0.36
0.15
0.36
0.55
0.22
0.4
0.8
0.3
0.8
0.7
0.5
0.8
1.0
0.7
1.9
1.7
1.2
3.1
2.9
2.1
5.1
4.3
3.2
7.8
7.0
5.2
10.4
11.1
8.2
18.4
18.9
14.0
Consumption per stoke (in liters, pressure in Bar)
Outward Stroke
Inward Stroke
Double-Acting and Spring-Return
Double-Acting only
2.0 barg 4.0 barg 8.0 barg 2.0 barg 4.0 barg 8.0 barg
0.29
0.50
0.9
0.46
0.85
1.6
0.29
0.50
0.9
0.46
0.85
1.6
0.47
0.8
1.5
0.87
1.6
3.0
0.9
1.6
3.1
1.3
2.4
4.6
1.0
1.7
3.2
2.0
3.6
6.9
2.1
3.6
6.8
1.9
3.4
6.2
2.4
4.0
7.3
2.7
4.6
8
5.1
9
17
5
8
15
8
14
27
8
14
25
13
23
44
12
20
37
21
36
68
19
33
62
29
50
92
30
53
97
51
87
161
52
89
165
Actuator volumes:
Maximum volume (in Cu.in.)
Central1
End cap2 Displaced3
chamber chamber
volume
3.1
3.7
2.5
6.4
11.8
4.7
10.0
22
8.9
22
34
13.5
22
50
19.9
48
43
32
50
59
44
118
103
76
189
174
129
310
260
193
477
430
319
638
676
501
1122
1151
853
Consumption per stoke (in Cu.in., pressure in psig)
Outward Stroke
Inward Stroke
Double-Acting and Spring-Return
Double-Acting only
40 psig
80 psig
120 psig
40 psig
80 psig
120 psig
11
19
28
13
23
33
23
40
58
37
70
102
36
64
92
70
131
192
74
134
194
107
200
293
80
140
200
158
295
433
163
295
427
151
270
389
182
320
458
207
369
532
402
729
1055
359
642
925
650
1171
1692
610
1091
1571
1049
1905
2760
910
1628
2346
1635
2951
4267
1505
2691
3877
2259
4018
5776
2367
4232
6097
3946
7040
10134
4027
7202
10377
Notes:
1. For Double-acting and Spring-return. Pistons at 90° outward position
2. Only for Double-acting. Pistons at 0° inward position
3. Stroke is 90°
Central air chamber volume
Double-Acting and Spring-Return
A
End cap air chamber volume
Double-Acting only
B
5
EL-O-Matic F-Series
Product Data Sheet
June 2014
EFG.01.02.EN Rev. 1
Construction, Parts and Materials
21
11
15
19
1
9
4
13
7
3
5
14
2
10
20
18
17
6
22
8
16
12
23
Notes:
1. Chromated and polyurethane powder coated
2. Chromated
3. Hard anodized
4. Electrophoretic coated
5. Deltatone® coated
Pos.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Qty.
1
2
2
1
Max. 12
2
2
2
1
8
1
2
2
2
2
2
2
2
2
2
1
1
1
*
*
*
*
*
*
*
*
*
*
Description
House
End cap
Piston
Pinion
Spring cartridge
Bearing strip piston rack
Bearing piston
Bearing pinion
Thrust washer
End cap screw
Circlip
O-ring seal pinion
O-ring seal piston
O-ring seal end cap
O-ring seal limit stop
B-port seal
Limit stop screw
Limit stop nut
Limit stop washer
Warning sticker
Indicator assembly
Center plate (option)
Insert drive
* = Included in Service Kit.
6
Material
Cast Aluminium alloy
Cast Aluminium alloy
Cast Aluminium alloy
High grade aluminium
Spring steel
POM
PTFE 25% carbon-filled
POM
POM, black UV-stabilized
Stainless Steel
Spring steel
Nitrile rubber
Nitrile rubber
Nitrile rubber
Nitrile rubber
Silicon rubber
Stainless steel
Stainless steel
PA66
Polyester
ABS + stainless steel screw
Nylon PA6, Black
Aluminium alloy
Notes
1
1
2
3
4
5
Product Data Sheet
EL-O-Matic F-Series
EFG.01.03.EN Rev. 3
May 2015
EL-O-Matic F Corrosion Protection System
Description
The corrosion protection system of a standard EL-O-Matic
F-Series pneumatic actuator consists of the following
treatments or materials:
Pre-treatment
The housing and end caps get a chromate pre-treatment prior
to painting. The pre-treatment takes care of a perfect bonding
of the paint layer to the aluminium housing and gives additional
corrosion protection to the bore of the housing.
Powder coat
„„Polyurethane powder coating for exterior use.
Stainless steel or Deltatone treated external
steel parts
External parts are stainless steel or steel alloy with a Deltatone®
treatment for optimum protection and durability.
The chemical and durability assessment
All these components, treatments and finishes, including the
durable pinion design, anodized surface finish, standard powder
coat paint and Stainless steel treated external fasteners shows
no decline of actuator functions after 500 hours salt spray test.
Technical Data
Coating : Polyurethane powder coating for
exterior use.
Salt spray test :
ASTM B117: 500 hours
„„The powder coating is applied cold using automatic
electrostatic spray equipment and is cured for about 10
minutes at a minimum of 200°C (392°F) offering excellent
light and weather resistance.
„„The powder coating thickness is between 80 and 160
microns (3.15 and 6.3 mils).
„„Good chemical resistance against most bases, acids,
solvents, alkalis and oils at normal temperatures.
„„Excellent exterior mechanical durability.
Color : Yellow (RAL 1007)
Materials: Housing:
Chromated aluminium alloy
Endcaps:
Chromated aluminium alloy
Pistons:
Chromated aluminium alloy
Pinion:
High grade aluminium alloy,
hard anodized (Option: Stainless steel)
Fasteners:
Stainless steel or alloy steel with
Deltatone® treatment
„„The coating has passed a salt spray test according to ASTM
B117 for 500 hours.
Type Sticker: Nylon
The powder coating is virtually solvent free, and therefore
environmentally friendly.
Application:
Standard EL-O-Matic F-Series
pneumatic actuators
High grade & hard anodized aluminium pinion
Actuators with high grade & hard anodized aluminium pinions,
passed a 500 hours salt spray test. Optional stainless steel
pinions are available for a higher corrosion resistance.
Table 1. Test result polyurethane powder coating
No
1
Item
Hardness
Standard
ASTM D3363 Pencil (Mitsubishi Uni)
2
Adhesion
ISO 2409, ASTM D3359 Cross hatch test (2 mm)
3
4
5
6
7
8
Impact test
Bend test
Acid resistance
Alkali resistance
Water resistance
Boiling test
ASTM D2794 5/8” Ball (direct)
DIN 53152, ISO1519, ASTM D522
ISO 2512 5% H2SO4, 1 Hour
ISO 2812 5% Na CO3, 1 hour
20° C, 7 days
1 hour @ 98°C
Specification
2H
Gt (0)
100% Adhesion
Min. 25 lb.in without detachment
Min 5 mm without cracking
No Blistering
No Blistering
No Blistering
No Blistering
1. This data sheet contains general information as supplied by the paint supplier and describes typical properties for the coating.
7
EL-O-Matic F-Series
Product Data Sheet
March 2014
EFG.01.04.EN Rev. 0
Assembly codes EL-O-Matic F actuators
Spring-return actuators
Assembly code: CW
Assembly code: CC
= Standard, Clockwise-to-Close rotation
= Reverse, Counterclockwise-to-Open
= Fail-to-Close
= Fail-to-Open
B
A
A
B
Pinion
Pistons
A
A
Spring
cartridge
B
B
Pistons
A = Central air chamber pressurized
B = Spring stroke
Double-acting actuators
Assembly code: CW
Assembly code: CC
= Standard, Clockwise-to-Close rotation
= Reverse, Counterclockwise-to-Open
B
A
A
Pinion
Pistons
A
B
B
A = Central air chamber pressurized
B = End cap air chambers pressurized
All views are from above. Pistons are shown in inward position.
8
A
B
Pistons
Product Data Sheet
EL-O-Matic F-Series
EFG.02.01.EN Rev. 1
May 2015
Product configuration code
FS 0150 . N U 40 CW AL T . NL17 S K A . 00 XX
Type
FD
FS
Double-Acting
Spring-Return
Size
0012
0025
0040
0065
0100
0150
0200
0350
Size 0012
Size 0025
Size 0040
Size 0065
Size 0100
Size 0150
Size 0200
Size 0350
Cycle Speed Option
Internal Code 1
Color/Finish
Visual Indicator
Temperature
Valve Stem Connection
Valve Interface
Pinion Material
Rotation Direction
Spring Set
Threads
Rotation Angle
Size
Type
Ÿ•
Rotation Angle
N
90° Rotation
Threads
M
Metric ISO 5211
U
UNC/NPT/Imperial
Spring Set
00
Double-Acting (No Springs)
10
Spring Set 10
20
Spring Set 20
30
Spring Set 30
40
Spring Set 40
50
Spring Set 50
60
Spring Set 60
Valve Stem Connection (Insert Sizes)
Parallel
Diagonal
Actuator
Square
Drive
Drive
Size(s)
0000
No Insert
NL09
ND09
9mm / 0.354" 0012
NL11
YD11
11mm / 0.433" 0025
NL14
YD14
14mm / 0.551" 0040 & 0065
17mm / 0.669"
NL19
YD17
0100 & 0150
19mm / 0.748"
NL22
YD22
22mm / 0.866" 0200
22mm / 0.866"
NL27
YD22
0350
27mm / 1.063"
See Insert Supplement for Additional Insert Options.
Temperature Ranges
S Standard: -20°C to +80°C (-4°F to +176°F)
H High: -20°C to +120°C (-4°F to +248°F)
L Low: -40°C to +80°C (-40°F to +176°F)
Visual Indicator Code
K Standard (Knob)
N No Visual Indicator
Finish
A Standard Coating
Ÿ•
Internal Code 1
00 Standard
Rotation Direction
CW
Spring to Close/Clockwise
CC
Spring to Open/Counterclockwise
Cycle Speed Options
XX Standard
H1 1/2" High Flow plate
Pinion Material
AL
High-Grade Aluminium, Hard Anodized
Notes
Valve Interface
T
Standard ISO 5211 Interface
S
Small Interface with Center Plate (DIN3337)
L
Large Interface with Center Plate (DIN3337)
These options are all options available. Not all options apply to
all configurations.
Valve Interface: Option "S"; Small Interface with Center Plate (DIN3337)
is not available for size 0025.
Ÿ•
9
EL-O-Matic F-Series
Product Data Sheet
March 2014
EFM.03.01.EN, Page 1 of 2, Rev. 0
Actuator
Size
FS 12
FS 25
FS 40
FS 65
FS 100
FS 150
FS 200
FS 350
FS 600
10
Spring
set nr.
Actuator Torque - Spring-Return (Nm)
Spring
Stroke
Torque
(Nm)
Start End
Air Stroke Torque (Nm)
SUPPLY PRESSURE
3.0 barg
3.5 barg
4.0 barg
4.5 barg
5.0 barg
5.5 barg
6.0 barg
7.0 barg
8.0 barg
Start End Start End Start End Start End Start End Start End Start End Start End Start End
20
7
5
2
-
4
1
5
2
6
3
8
5
9
6
10
7
13
10
15
12
10
4
2
12
10
14
13
17
15
19
17
21
20
24
22
26
25
31
29
36
34
20
7
4
9
6
12
9
14
11
16
13
19
16
21
18
24
21
28
25
33
30
30
11
7
7
2
9
4
11
7
14
9
16
12
19
14
21
17
26
21
31
26
40
14
9
-
-
-
-
9
3
11
5
14
8
16
10
18
12
23
17
28
22
50
18
11
-
-
-
-
-
-
9
1
11
4
14
6
16
8
21
13
26
18
60
21
13
-
-
-
-
-
-
-
-
-
-
11
2
13
4
18
9
23
14
10
7
4
22
19
26
24
31
28
36
33
40
37
45
42
49
46
58
55
67
64
20
13
8
17
12
22
16
26
21
31
25
35
30
40
34
44
39
53
48
62
57
30
20
12
12
4
17
9
21
13
26
18
31
22
35
27
40
31
49
40
58
49
40
26
17
-
-
12
1
17
6
21
10
26
15
30
19
35
24
44
33
53
42
50
33
21
-
-
-
-
-
-
17
3
21
7
26
12
30
16
39
25
48
34
60
39
25
-
-
-
-
-
-
-
-
-
-
21
4
25
9
34
18
43
27
10
10
6
33
29
40
36
47
43
54
50
61
57
68
63
75
70
88
84
102
98
20
20
13
26
17
33
24
40
31
47
38
53
45
60
52
67
59
81
72
95
86
30
31
19
19
5
25
12
32
19
39
26
46
33
53
40
60
47
74
61
87
74
40
41
26
-
-
-
-
25
8
32
14
39
21
46
28
52
35
66
49
80
63
50
51
32
-
-
-
-
-
-
24
3
31
10
38
17
45
23
59
37
73
51
60
61
39
-
-
-
-
-
-
-
-
-
-
31
5
38
12
52
25
65
39
10
15
9
49
43
60
53
70
64
80
74
90
84
100
94
111
104
131
125
151
145
20
30
19
39
26
49
36
59
47
69
57
79
67
90
77
100
87
120
108
141
128
30
44
28
28
9
38
19
48
30
59
40
69
50
79
60
89
70
109
91
130
111
40
59
37
-
-
27
2
38
13
48
23
58
33
68
43
78
53
99
74
119
94
50
74
47
-
-
-
-
-
-
37
6
47
16
57
26
68
36
88
57
108
77
60
89
56
-
-
-
-
-
-
-
-
-
-
47
9
57
19
77
40
98
60
10
24
15
79
69
96
86
112
102
128
118
145
135
161
151
177
167
210
200
243
233
20
47
30
62
42
79
59
95
75
111
91
128
108
144
124
160
140
193
173
226
206
30
71
44
45
15
62
32
78
48
94
64
111
81
127
97
143
113
176
146
209
179
40
94
59
-
-
45
5
61
21
77
37
94
54
110
70
126
86
159
119
192
152
50
118
74
-
-
-
-
-
-
60
10
77
26
93
43
109
59
142
92
175
124
60
141
89
-
-
-
-
-
-
-
-
-
-
76
16
92
32
125
65
158
97
10
33
21
108
94
131
117
153
139
175
161
198
184
220
206
242
228
287
273
332
318
20
65
41
85
57
107
79
129
102
152
124
174
146
196
169
219
191
263
236
308
280
30
98
62
61
19
83
42
106
64
128
86
150
109
173
131
195
153
240
198
284
243
40
131
82
-
-
-
-
82
26
104
49
127
71
149
93
171
116
216
161
261
205
50
163
103
-
-
-
-
-
-
81
11
103
34
125
56
148
78
192
123
237
168
60
196
124
-
-
-
-
-
-
-
-
-
-
102
18
124
41
169
85
213
130
10
56
35
189
165
227
204
266
243
305
281
344
320
383
359
422
398
499
476
577
553
20
112
70
148
101
187
139
226
178
265
217
303
256
342
295
381
334
459
411
537
489
30
168
106
108
36
146
75
185
114
224
153
263
192
302
231
341
269
418
347
496
425
40
224
141
-
-
106
11
145
50
184
89
222
127
261
166
300
205
378
283
455
360
50
280
176
-
-
-
-
-
-
143
24
182
63
221
102
260
141
337
218
415
296
60
335
211
-
-
-
-
-
-
-
-
-
-
180
38
219
77
297
154
374
232
10
96
60
320
279
386
345
452
411
518
477
584
543
650
609
716
675
848
807
980
939
20
192
121
251
169
317
235
383
301
449
367
515
433
581
499
647
565
779
697
911
829
30
287
181
181
59
247
125
313
191
379
257
445
323
511
389
577
455
709
587
841
719
40
383
241
-
-
178
15
244
81
310
147
376
213
442
279
508
345
640
477
772
609
50
479
302
-
-
-
-
-
-
241
37
307
103
373
169
439
235
571
367
703
499
60
575
362
-
-
-
-
-
-
-
-
-
-
303
59
369
125
501
257
633
389
Product Data Sheet
EL-O-Matic F-Series
EFM.03.01.EN, Page 2 of 2, Rev. 0
March 2014
Actuator
Size
FS 950
FS 1600
FS 2500
FS 4000
Note:
Spring
set nr.
Actuator Torque - Spring-Return (Nm)
Spring
Stroke
Torque
(Nm)
Start End
Air Stroke Torque (Nm)
SUPPLY PRESSURE
3.0 barg
3.5 barg
4.0 barg
4.5 barg
5.0 barg
5.5 barg
6.0 barg
7.0 barg
8.0 barg
Start End Start End Start End Start End Start End Start End Start End Start End Start End
10
150
95
496
432
598
534
701
637
803
739
906
842
1008
944
1110 1047
1315 1251
1520 1456
20
300
189
387
259
490
362
592
464
694
567
797
669
899
772
1002
874
1207 1079
1412 1284
30
450
284
278
87
381
189
483
292
586
394
688
497
791
599
893
702
1098
907
1303 1111
40
600
378
-
-
-
-
375
119
477
222
580
324
682
427
784
529
989
734
1194
939
50
750
473
-
-
-
-
-
-
368
49
471
152
573
254
676
357
881
562
1086
767
60
900
567
-
-
-
-
-
-
-
-
-
-
465
82
567
184
772
389
977
594
10
246
155
811
707
979
875
1147 1042
1314 1210
1482 1377
1650 1545
1817 1713
2153 2048
2488 2383
20
491
309
634
425
801
592
969
760
1136
928
1304 1095
1472 1263
1639 1431
1975 1766
2310 2101
30
737
464
456
142
623
310
791
478
959
645
1126
813
1294
981
1462 1148
1797 1484
2132 1819
40
982
619
-
-
-
-
613
195
781
363
948
531
1116
698
1284
866
1619 1201
1954 1537
50
1228
773
-
-
-
-
-
-
603
81
771
249
938
416
1106
584
1441
919
1777 1254
60
1473
928
-
-
-
-
-
-
-
-
-
-
761
134
928
302
1263
637
1599
10
396
249
1308 1140
1578 1410
1848 1680
2119 1950
2389 2221
2659 2491
2929 2761
3470 3302
4010 3842
20
792
499
1021
685
1292
955
1562 1225
1832 1495
2102 1766
2373 2036
2643 2306
3183 2847
3724 3387
30
1187
748
735
230
1005
500
1275
770
1545 1040
1816 1311
2086 1581
2356 1851
2897 2392
3437 2932
40
1583
997
-
-
-
-
988
315
1259
585
1529
856
1799 1126
2070 1396
2610 1937
3151 2477
50
1979 1247
-
-
-
-
-
-
972
130
1242
401
1513
671
1783
941
2323 1482
2864 2022
60
2375 1496
-
-
-
-
-
-
-
-
-
-
1226
216
1496
486
2037 1027
2577 1567
10
633
399
2093 1823
2525 2256
2958 2688
3390 3121
3822 3553
4255 3986
4687 4418
5552 5283
6417 6148
20
1267
798
1634 1095
2067 1528
2499 1960
2931 2393
3364 2825
3796 3258
4229 3690
5094 4555
5958 5420
30
1900 1197
1175
367
1608
800
2040 1232
2473 1665
2905 2097
3338 2530
3770 2962
4635 3827
5500 4692
40
2533 1596
-
-
-
-
1582
504
2014
937
2447 1369
2879 1802
3311 2234
4176 3099
5041 3964
50
3167 1995
-
-
-
-
-
-
1555
209
1988
641
2420 1074
2853 1506
3718 2371
4583 3236
60
3800 2394
-
-
-
-
-
-
-
-
-
-
1962
2394
3259 1643
4124 2508
1. Emerson Process Management recommends that the valve
manufacturer supply the maximum required torque values
(Including any adjustments or suggested safety factors for valve
service conditions or application).
2. Additionally, the valve manufacturer must identify at which
position(s) and direction(s) of rotation (Counterclockwise or
Clockwise) these maximum requirements occur.
3. If in doubt, or you require any assistance with sizing actuators, do
not hesitate to contact your nearest Emerson's Valve Automation
representative.
Figure 1.
346
778
972
Spring-return torque diagram
Air stroke
Spring stroke
Start
Torque
Rotation
Counter Clockwise
Start
End
Torque
End
Rotation
Clockwise
11
EL-O-Matic F-Series
Product Data Sheet
March 2014
EFI.03.01.EN, Page 1 of 2, Rev. 1
Actuator Torque - Spring-Return (lbf.in)
Air Stroke Torque (lbf.in)
SUPPLY PRESSURE
70 psig
80 psig
90 psig
Start End Start End Start End
Spring
set nr.
Spring Stroke
Torque
Actuator
Size
FS 12
20
64
41
15
-
31
5
47
21
63
37
79
53
95
69
111
84
142
116
10
31
20
93
80
123
109
152
139
181
168
211
198
240
227
270
257
329
316
20
63
39
70
44
100
73
129
103
159
132
188
162
218
191
247
221
306
280
30
94
59
48
8
77
37
107
67
136
96
166
126
195
155
225
185
283
244
40
125
79
-
-
-
-
84
31
113
60
143
90
172
119
202
149
261
208
50
156
99
-
-
-
-
-
-
91
24
120
54
150
83
179
113
238
172
60
188
118
-
-
-
-
-
-
-
-
98
18
127
47
157
77
216
136
10
58
37
175
150
230
206
285
261
341
316
396
371
451
427
506
482
617
592
20
116
73
133
84
188
139
243
195
299
250
354
305
409
360
464
415
575
526
30
174
110
91
18
146
73
201
128
257
183
312
239
367
294
422
349
533
459
40
231
146
-
-
-
-
159
62
214
117
270
172
325
227
380
283
491
393
50
289
183
-
-
-
-
-
-
172
50
228
106
283
161
338
216
449
327
60
347
220
-
-
-
-
-
-
-
-
186
39
241
94
296
150
407
260
10
90
57
265
227
349
311
434
395
518
479
602
564
686
648
770
732
939
900
20
181
114
200
123
284
207
368
291
452
376
537
460
621
544
705
628
873
796
30
271
171
134
19
219
103
303
188
387
272
471
356
555
440
639
524
808
693
40
361
228
-
-
-
-
237
84
322
168
406
252
490
336
574
420
742
589
50
452
285
-
-
-
-
-
-
256
64
340
148
424
232
509
317
677
485
60
542
341
-
-
-
-
-
-
-
-
275
44
359
129
443
213
612
381
10
131
83
394
339
518
463
643
588
767
712
892
836
1016
961
1141
1085
1390
1334
20
262
166
299
188
423
313
548
437
672
562
797
686
921
811
1046
935
1295
1184
30
392
248
203
38
328
162
452
287
577
411
701
536
826
660
950
785
1199
1034
40
523
331
-
-
-
-
357
136
482
261
606
385
731
510
855
634
1104
883
50
654
414
-
-
-
-
-
-
387
110
511
235
636
359
760
484
1009
733
60
785
497
-
-
-
-
-
-
-
-
416
85
540
209
665
334
914
583
10
208
131
633
544
832
743
1031
942
1231
1142
1430
1341
1629
1540
1829
1740
2227
2138
20
416
262
482
304
681
504
881
703
1080
902
1279
1102
1479
1301
1678
1500
2077
1899
30
625
393
332
65
531
264
730
464
930
663
1129
862
1328
1062
1528
1261
1926
1660
40
833
524
-
-
-
-
580
224
779
424
979
623
1178
823
1377
1022
1776
1421
50
1041
654
-
-
-
-
-
-
629
185
828
384
1027
583
1227
783
1626
1181
60
1249
785
-
-
-
-
-
-
-
-
678
145
877
344
1076
543
1475
942
10
289
182
862
739
1135
1012
1408
1285
1681
1558
1954
1831
2226
2104
2499
2376
3045
2922
20
578
364
653
407
926
680
1198
953
1471
1226
1744
1499
2017
1771
2290
2044
2836
2590
30
867
547
443
75
716
348
989
621
1262
894
1535
1166
1808
1439
2080
1712
2626
2258
40
1156
729
-
-
-
-
780
289
1052
561
1325
834
1598
1107
1871
1380
2417
1926
50
1445
911
-
-
-
-
-
-
843
229
1116
502
1389
775
1662
1048
2207
1593
60
1734
1093
-
-
-
-
-
-
-
-
906
170
1179
443
1452
716
1998
1261
10
495
312
1503
1293
1978
1767
2452
2241
2926
2716
3400
3190
3874
3664
4348
4138
5296
5086
20
990
624
1145
724
1619
1199
2093
1673
2567
2147
3041
2621
3515
3095
3990
3569
4938
4517
30
1485
936
786
156
1261
630
1735
1104
2209
1578
2683
2052
3157
2526
3631
3000
4579
3948
40
1979
1248
-
-
-
-
1376
535
1850
1009
2324
1483
2798
1957
3272
2431
4221
3380
50
2474
1560
-
-
-
-
-
-
1492
440
1966
914
2440
1388
2914
1863
3862
2811
60
2969
1872
-
-
-
-
-
-
-
-
1607
346
2081
820
2555
1294
3504
2242
10
848
534
2551
2190
3356
2996
4162
3801
4968
4607
5773
5413
6579
6218
7385
7024
8996
8635
20
1695
1068
1937
1216
2743
2021
3548
2827
4354
3633
5160
4438
5965
5244
6771
6050
8382
7661
30
2543
1601
1324
241
2129
1047
2935
1853
3741
2658
4546
3464
5352
4270
6158
5075
7769
6687
40
3391
2135
-
-
-
-
2321
878
3127
1684
3933
2490
4738
3295
5544
4101
7155
5712
50
4238
2669
-
-
-
-
-
-
2513
710
3319
1515
4125
2321
4930
3127
6542
4738
60
5086
3203
-
-
-
-
-
-
-
-
2706
541
3511
1346
4317
2152
5928
3763
FS 25
FS 40
FS 65
FS 100
FS 150
FS 200
FS 350
FS 600
12
(lbf.in)
Start End
40 psig
Start End
50 psig
Start End
60 psig
Start End
100 psig
Start End
120 psig
Start End
Product Data Sheet
EL-O-Matic F-Series
EFI.03.01.EN, Page 2 of 2, Rev. 1
March 2014
Actuator
Size
FS 950
FS 1600
FS 2500
FS 4000
Note:
Spring
set nr.
Actuator Torque - Spring-Return (lbf.in)
60 psig
Start End
Air Stroke Torque (lbf.in)
SUPPLY PRESSURE
70 psig
80 psig
90 psig
Start End Start End Start End
Spring Stroke
Torque
(lbf.in)
Start End
40 psig
Start End
50 psig
Start End
100 psig
Start End
120 psig
Start End
10
1328
837
3950
3385
5200
4635
6451
5886
7701
7136
8952
8387
10202 9637
11453 10888 13954 13389
20
2656
1673
2988
1859
4239
3109
5489
4360
6740
5610
7990
6861
9241
8111
10491 9362
12992 11863
30
3983
2510
2027
333
3277
1583
4528
2834
5778
4084
7029
5334
8279
6585
9530
7835
12030 10336
40
5311
3346
-
-
-
-
3566
1307
4817
2558
6067
3808
7318
5059
8568
6309
11069 8810
50
6639
4183
-
-
-
-
-
-
3855
1032
5106
2282
6356
3532
7606
4783
10107 7284
60
7967
5019
-
-
-
-
-
-
-
-
4144
756
5394
2006
6645
3257
9146
10
2173
1369
6464
5540
8510
7586
10557 9633
12603 11679 14650 13726 16696 15772 18743 17819 22836 21911
5758
20
4346
2738
4890
3042
6937
5088
8983
7135
11030 9181
13076 11228 15123 13274 17169 15321 21262 19414
30
6519
4107
3317
544
5363
2591
7410
4637
9456
6684
11503 8730
40
8692
5476
-
-
-
-
5836
2139
7882
4186
9929
6232
11975 8279
14022 10325 18115 14418
50
10865
6845
-
-
-
-
-
-
6309
1688
8355
3734
10402 5781
12448 7827
16541 11920
60
13038
8214
-
-
-
-
-
-
-
-
6782
1237
8828
10875 5330
14968 9423
13549 10776 15595 12823 19688 16916
3283
10
3503
2207
10420 8930
13719 12229 17018 15528 20317 18827 23616 22126 26915 25425 30214 28724 36812 35322
20
7006
4414
7883
4904
11182 8203
14481 11502 17780 14801 21079 18100 24378 21399 27678 24698 34276 31296
30
10509
6621
5347
877
8646
4176
11945 7475
15244 10774 18543 14073 21842 17372 25141 20671 31739 27269
40
14012
8828
-
-
-
-
9408
3449
12707 6748
16006 10047 19305 13346 22604 16645 29202 23243
50
17515 11035
-
-
-
-
-
-
10170 2721
13469 6020
16768 9319
20067 12618 26665 19216
60
21018 13242
-
-
-
-
-
-
10933 1994
14232 5293
17531 8592
10
5605
3531
16673 14289 21952 19568 27230 24847 32509 30125 37788 35404 43066 40683 48345 45961 58903 56519
7063
-
-
24129 15190
20
11210
12614 7846
17893 13125 23171 18404 28450 23683 33729 28961 39008 34240 44286 39519 54844 50076
30
16816 10594
8555
1404
13834 6682
40
22421 14125
-
-
-
-
50
28026 17656
-
-
-
-
-
-
60
33631 21188
-
-
-
-
-
-
19112 11961 24391 17240 29670 22518 34949 27797 40227 33076 50785 43633
15054 5518
1. Emerson Process Management recommends that the valve
manufacturer supply the maximum required torque values
(Including any adjustments or suggested safety factors for valve
service conditions or application).
2. Additionally, the valve manufacturer must identify at which
position(s) and direction(s) of rotation (Counterclockwise or
Clockwise) these maximum requirements occur.
3. If in doubt, or you require any assistance with sizing actuators, do
not hesitate to contact your nearest Emerson's Valve Automation
representative.
20332 10797 25611 16076 30890 21354 36168 26633 46726 37190
16273 4354
-
-
Figure 1.
21552 9633
26831 14912 32109 20190 42667 30748
17493 3190
22772 8469
28050 13747 38608 24305
Spring-return torque diagram
Air stroke
Spring stroke
Start
Torque
Rotation
Counter Clockwise
Start
End
Torque
End
Rotation
Clockwise
13
EL-O-Matic F-Series
Product Data Sheet
April 2014
EFM.03.02.EN, Rev. 0
Actuator Torque - Double-Acting (Nm)
Torque in Nm
Supply Pressure (barg)
Actuator
Size
2
3
3.5
4
4.5
5
5.5
6
6.5
7
8
FD 12
4.8
7.3
8.5
9.7
10.9
12.2
13.4
14.6
15.9
17.1
19.6
FD 25
9
13
16
18
20
23
25
27
29
32
36
FD 40
17
25
29
34
38
42
47
51
55
59
68
FD 65
25
38
45
51
58
64
71
77
84
90
103
FD 100
38
57
66
76
86
95
105
115
124
134
153
FD 150
60
91
106
122
137
153
168
183
199
214
245
FD 200
82
124
146
167
188
209
230
251
272
293
335
FD 350
143
216
253
290
326
363
400
436
473
510
583
FD 600
243
368
430
492
554
617
679
741
804
866
991
FD 950
377
570
667
764
861
957
1054
1151
1247
1344
1537
FD 1600
617
934
1092
1250
1408
1567
1725
1883
2041
2200
2516
FD 2500
995
1505
1760
2015
2270
2525
2780
3036
3291
3546
4056
FD 4000
1592
2408
2816
3225
3633
4041
4449
4857
5265
5673
6490
Note:
1. Emerson Process Management recommends that the valve
manufacturer supply the maximum required torque values
(Including any adjustments or suggested safety factors for valve
service conditions or application).
2. Additionally, the valve manufacturer must identify at which
position(s) and direction(s) of rotation (Counterclockwise or
Clockwise) these maximum requirements occur.
3. If in doubt, or you require any assistance with sizing actuators, do
not hesitate to contact your nearest Emerson's Valve Automation
representative.
Figure 1.
Double-acting torque diagram
Start
End
Torque
Rotation
14
Product Data Sheet
EL-O-Matic F-Series
EFI.03.02.EN, Rev. 0
April 2014
Actuator Torque - Double-Acting (lbf.in)
Torque in lbf.in
Supply pressure (psig)
Actuator
Size
30
35
40
45
50
55
60
70
75
80
90
100
120
FD 12
44
51
59
66
74
81
89
104
112
119
134
149
179
FD 25
81
95
109
123
137
151
165
193
207
220
248
276
332
FD 40
153
179
205
231
257
283
309
361
387
413
466
518
622
FD 65
233
272
312
352
392
431
471
550
590
630
709
789
948
FD 100
344
403
461
520
579
638
696
814
873
931
1049
1166
1401
FD 150
551
645
739
833
927
1021
1115
1304
1398
1492
1680
1868
2244
FD 200
754
883
1011
1140
1269
1398
1527
1784
1913
2042
2299
2557
3072
FD 350
1310
1534
1758
1981
2205
2429
2653
3100
3324
3547
3995
4442
5337
FD 600
2226
2606
2987
3367
3747
4127
4508
5268
5648
6028
6789
7549
9070
FD 950
3455
4045
4636
5226
5816
6406
6996
8177
8767
9357
10537
11717
14078
FD 1600
5655
6621
7586
8552
9518
10484
11450
13381
14347
15313
17244
19176
23039
FD 2500
9116
10673
12230
13787
15344
16900
18457
21571
23128
24685
27799
30913
37141
FD 4000
14586
17077
19568
22060
24551
27042
29533
34516
37007
39498
44481
49463
59428
Note:
1. Emerson Process Management recommends that the valve
manufacturer supply the maximum required torque values
(Including any adjustments or suggested safety factors for valve
service conditions or application).
2. Additionally, the valve manufacturer must identify at which
position(s) and direction(s) of rotation (Counterclockwise or
Clockwise) these maximum requirements occur.
3. If in doubt, or you require any assistance with sizing actuators, do
not hesitate to contact your nearest Emerson's Valve Automation
representative.
Figure 2. Double-acting torque diagram
Start
End
Torque
Rotation
15
EL-O-Matic F-Series
Product Data Sheet
March 2014
EFG.03.03.EN, Page 1 of 2, Rev. 0
Sizing of Rack & Pinion actuators
Sizing is the selection procedure to select the right size of
actuator on a valve with a given torque characteristic. This data
sheet gives brief samples on how to size actuators and which
data is needed.
Sizing Double-acting actuators
Figure 2. Double-acting torque characteristicTorque output
( opening )
Torque output
( closing )
Torque characteristics of valves
EL-O-Matic F actuators are commonly used to operate butterfly-,
ball- and plug valves. The below instructions are intended for
these valve applications, but can also be used for other quarter
turn applications.
Figure 1.
Generic torque characteristic of a valve
Close
Break torque
Torque
Open
Open
Close
Re-seating torque
Run torque
Close
Open
Opening stroke
Sample calculation of double-acting sizing
Run torque
Open
Close
Closing stroke
Valve torque values and safety factors
Emerson Process Management recommends that the valve
manufacturer supply the maximum required and allowed
torque values (Including any adjustments or suggested safety
factors for valve service conditions or application).
Additionally, the valve manufacturer must identify at which
position(s) and direction(s) of rotation (Counterclockwise or
Clockwise) these maximum requirements occur.
If in doubt or if you require any assistance with sizing actuators,
do not hesitate to contact your nearest Emerson's Valve
Automation representative.
16
Torque
„„Publish valve break torque:
40 Nm
354 Ibf.in
„„Publish maximum stem torque:
105 Nm
929 lbf.in
„„Recommended safety factor:
1.2 (20%)
„„Minimum supply pressure:
5.5 bar
80 psi
„„Maximum supply pressure:
6.5 bar
94 psi
Calculation:
1. Because the recommended safety factor is 1.2 the sizing
torque will be 40 x 1.2 = 48 Nm (354 x 1.2 = 425 lbf.in).
2. Lookup in the double-acting torque table, in the 5.5 bar
column (or 80 psi column), from top down, the first actuator
size that generates more than 48 Nm (or 425 lbf.in).
3. Size FD65 is the first actuator that supplies more than
a. 48 Nm (71 Nm) at 5.5 bar.
b. 425 lbf.in (630 lbf.in) at 80 PSI.
4. The maximum torque output of a FD65 is 84 Nm (743 lbf.in).
This is lower than the maximum stem torque of 105Nm.
Conclusion
Because FD65 supplies more torque than the sizing torque (see
point 3) and less than the maximum stem torque (see point 4),
size FD65 is suitable to operate this valve.
Product Data Sheet
EL-O-Matic F-Series
EFG.03.03.EN, Page 2 of 2, Rev. 0
March 2014
Sizing spring-return actuators
Calculation:
1. Because the recommended safety factor is 1.5 the sizing
torques will be:
Figure 3. Spring-to-Close configuration
start
end
start
end
Torque
Close
Open
Open
Close
Table 1. For Fail-to Close actuators applies:
——Break
150 Nm x 1.5 = 225 Nm
1991 lbf.in
——Run open
45 Nm x 1.5 = 67.5 Nm
597 lbf.in
——Run close
45 Nm x 1.5 = 67.5 Nm
597 lbf.in
——Re-seat
90 Nm x 1.5 = 135 Nm
1195 lbf.in
2. Lookup in the spring-return torque table, in the "spring end"
torque column, from top down, the first actuator size that
generates more than 135 Nm (or 1195 lbf.In) of re-seat
torque.
3. Size FS350 with spring set 4 is the first actuator that supplies
more spring end torque (149 Nm or 1655 lbf.In).
4. Check now for the other three positions whether the
actuator torque exceeds the valve torques.
Actuator stroke:
Valve Stroke:
Air-Start torque
> Break torque
and
Actuator stroke:
Valve Stroke:
Air-End torque
> Run open torque
and
Air-Start: 252 Nm
> Break open: 225 Nm
Spring-Start torque
> Run open torque
and
Air-End: 157 Nm
> Run open: 67.5 Nm
Spring-End torque
> Re-seat torque
Spring-Start: 232 Nm
> Run close: 67.5 Nm
Spring-End: 149 Nm
> Re-seat: 135 Nm
Table 2. For Fail-to Open actuators applies:
Actuator stroke:
Valve Stroke:
Spring-Start torque
> Break torque
and
Spring-End torque
> Run torque
and
Air-Start torque
> Run torque
and
Air-End torque
> Re-seat torque
Sample calculation spring-return sizing for a
Spring-to-Close application
„„Published valve torques
——
Break torque:
150 Nm
1328 lbf.in
——
Run torque opening:
45 Nm
398 lbf.in
——
Run torque closing:
45 Nm
398 lbf.in
——
Re-seating torque;
90 Nm
797 lbf.in
„„Publish maximum stem torque:
375 Nm
3496 lbf.in
„„Recommended safety factor:
1.5 (50%)
„„Minimum supply pressure:
5.5 bar
80 psi
„„Maximum supply pressure:
6.0 bar
87 psi
5. The maximum torque output of a FS350 with springset 4 at
maximum pressure of 6 bar is 291 Nm (2575 lbf.in). This is
lower than the maximum stem torque of 375 Nm (3496 lbf.in).
Conclusion
Because FS350 n=40 supplies more torque than the sizing
torque (see point 3) and less than the maximum stem torque
(see point 5), size FS350 n=40 is suitable to operate this valve.
Note:
„„If the first found actuator does not exceed the valve torque at
all the positions, check the next size actuator.
„„If
the next size actuator does exceed the valve torque at
all the positions, but fails at maximum stem torque check
whether the same actuator but with a higher springset
(i.e. 50 instead of 40) does meet this requirement.
17
EL-O-Matic F-Series
Product Data Sheet
March 2014
EFG.03.04.EN Rev. 0
Spring cartridge placement
When replacing spring cartridges in a spring-return actuator, ensure that the cartridges are replaced in their identical position from
where they were removed.
Check below figure to see where to place the spring cartridges in case of spring set conversion.
Before assembling the spring cartridges and end caps, make sure that the pistons are completely inwards.
Figure 1.
Spring cartridge placement
6
N = 30
2
5
1
4
3
6
N = 20
5
2
2
4
3
1
N = 10
5
1
4
3
6
A
A = Piston top view
B = Position of piston gear rack
18
6
4
3
5
2
N = 50
1
6
4
5
1
2
N = 40
5
2
1
4
3
6
3
B
N = 60
Product Data Sheet
EL-O-Matic F-Series
EFM.06.0012.EN Rev. 0
March 2014
Data sheet F12
Metric - ISO5211
E
M5x8
G1/4"
15
F
I
G
Principle
Pneumatic rack & pinion actuator
General data
Bore
46
mm
Stroke
12.6
mm
SR
0.6
kg
Weight
DA
0.7
kg
Port A 0.05
L
Volume
Port B 0.06
L
Air connection
2x 1/8"
BSP
MOP 8
barg
SR
3-8
barg
Pressure range
DA
0.2 - 8
barg
Clean, dry or lubricated air
Pressure media
or inert gas
Cycle speed DA
Open 0.4
Sec.
Close 0.4
Sec.
Cycle speed SR
Open 0.4
Sec.
Close 0.4
Sec.
Temperature range
-20°C to +80°C
Lubrication
Lubricated for life (1
Stroke
90°
Finish
Polyurethane powder coat
Y
D
E2
K1 C
J
45
M
N ±0.5
K
L
L1
.5
W1
X
O
H
øP
+0
øV
W
T
W2
R
U U1
A
B
4
Dim in mm.
1. According to EN 15714-3
2. Test conditions:
Solenoid with flow capacity: 0.6 m3/hr
Pipe diameter: 6 mm
Medium: clean air
Supply pressure: 5.5 barg ~ 80psig
Load: with average load
Stroke: 90°
Temperature: Room temperature
Size 12
A FD
B FS
C
D
E
E2
F
G
H
I
103
118
60
20
16
23
10
12
60
33
J
K
K1
L
L1
M
N
21
12.7
6.4
25.4
50.8
16.5
1
O max. O min.
R
R1
T
U
V
W
W1
W2
40
40
40
31
42
M6x8
M4x7
M4x7
9.14
P
9.05
12.1
X
Y
G1/8" M6x12
Torque Output
Spring-return
Spring
set
2
Spring Stroke
Torque
Start
End
7.2
4.6
Double-acting
Air Stroke Torque (Nm)
3.0 barg
3.5 barg
4.0 barg
4.5 barg
5.0 barg
5.5 barg
6.0 barg
7.0 barg
8.0 barg
Start End Start End Start End Start End Start End Start End Start Start Start End Start End
-
-
3.8
7.3
1
8.5
5.1
2.3
6.4
9.7
3.6
11.0
7.7
4.9
12.2
9.0
6.2
13.4
10.3
7.5
12.9 10.1 15.6 12.8
14.6
17.1
19.6
„„Flange and square drive to ISO 5211
European Directives:
„„PED : suitable for use with group 2 gases according to
Pressure Equipment Directive 97/23/EC
„„Option: Solenoid mounting interface according to VDI/VDE
„„ATEX : suitable for use in hazardous areas classified as II 2 GD,
Notes:
„„Volume is the actual free air volume at 1 atm
3845 (NAMUR). See dotted image.
zones 1 or 2 (gases) and 21 or 22 (dust).
„„For further information regarding options, materials,
certifications and additional execution please contact your
regional sales office
19
EL-O-Matic F-Series
Product Data Sheet
March 2014
EFI.06.0012.EN Rev. 0
Data sheet F12
Imperial - ISO5211
UNC10-24
x .31
E
Principle
0.59
F
G
I
Pneumatic rack & pinion actuator
Y
General data
D
1/4" NPT
E2
K1 C
J
1.811
inch
Stroke
0.496
inch
SR
1.3
lb
DA
1.5
lb
Weight
1.77
M
N
K
L
L1
W1
X
Bore
Volume
±0.02
O
Port A 3.1
cu.in.
Port B 3.7
cu.in.
Air connection
H
Pressure range
2x 1/4"
NPT
MOP
116
psig
SR
43 - 116
psig
.0
2
DA
W
T
øP
+0
øV
Pressure media
W2
Cycle speed DA (2
R
U U1
A
B
4
Dim in mm.
A FD
B FS
103
J
Cycle speed SR (2
Size 12
C
D
E
E2
F
G
H
I
118
60
20
16
23
10
K
K1
L
L1
M
N
12
60
33
21
12.7
6.4
25.4
50.8
16.5
1
R
R1
T
U
V
W
W1
W2
40
40
40
31
42
M6x8
M4x7
M4x7
O max. O min.
9.14
12.1
X
Y
Close
0.4
Sec.
Open
0.4
Sec.
Close
0.4
Sec.
Temperature range
-40°F to +176°C
Lubrication
Lubricated for life (1
Stroke
90°
Finish
Polyurethane powder coat
1. According to EN 15714-3
2. Test conditions:
Solenoid with flow capacity: 21 foot3/hr
Pipe diameter: 1/4"
Medium: clean air
Supply pressure: 5.5 barg ~ 80psig
Load: with average load
Stroke: 90°
Temperature: Room temperature
P
9.05
3 - 116
psig
Clean, dry or lubricated air
or inert gas
Open 0.4
Sec.
G1/8" M6x12
Torque Output
Spring-return
Spring
set
2
Spring Stroke
Torque
Start
End
7.2
4.6
Double-acting
Air Stroke Torque (Nm)
3.0 barg
3.5 barg
4.0 barg
4.5 barg
5.0 barg
5.5 barg
6.0 barg
7.0 barg
8.0 barg
Start End Start End Start End Start End Start End Start End Start Start Start End Start End
-
-
3.8
7.3
1
8.5
5.1
2.3
6.4
9.7
3.6
11.0
7.7
4.9
12.2
9.0
6.2
13.4
10.3
7.5
12.9 10.1 15.6 12.8
14.6
17.1
19.6
„„Flange and square drive to ISO 5211
European Directives:
„„PED : suitable for use with group 2 gases according to
Pressure Equipment Directive 97/23/EC
„„Option: Solenoid mounting interface according to VDI/VDE
„„ATEX : suitable for use in hazardous areas classified as II 2 GD,
Notes:
„„Volume is the actual free air volume at 1 atm
3845 (NAMUR). See dotted image.
„„For further information regarding options, materials,
certifications and additional execution please contact your
regional sales office
20
zones 1 or 2 (gases) and 21 or 22 (dust).
Product Data Sheet
EL-O-Matic F-Series
EFD.06.0012.EN Rev. 0
March 2014
Data sheet F12
Metric - DIN3337
E
M5x8
G1/4"
Principle
15
F
I
G
Y
Pneumatic rack & pinion actuator
General data
D
E2
K1 C
J
45
N
L
L1
46
mm
Stroke
12.6
mm
SR
0.6
kg
DA
0.7
kg
Weight
M
K
W1
X
Bore
±0.5
Volume
øP+0.5
Port A 0.05
L
Port B 0.06
L
Air connection
H
Pressure range
2x 1/8"
BSP
MOP
8
barg
SR
3-8
barg
DA
øV
O
W
T
Pressure media
W2
Cycle speed DA
R
U U1
A
B
Cycle speed SR
4
Dim in mm.
Size 12
A FD
B FS
C
D
E
E2
F
G
H
I
103
118
60
20
16
23
10
12
60
33
J
K
K1
L
L1
M
N
21
12.7
6.4
25.4
50.8
16.5
1
O max. O min.
R
R1
T
U
V
W
W1
W2
40
40
40
31
42
M6x8
M4x7
M4x7
9.14
12.1
X
Y
Close
0.4
Sec.
Open
0.4
Sec.
Close
0.4
Sec.
Temperature range
-20°C to +80°C
Lubrication
Lubricated for life (1
Stroke
90°
Finish
Polyurethane powder coat
1. According to EN 15714-3
2. Test conditions:
Solenoid with flow capacity: 0.6 m3/hr
Pipe diameter: 6 mm
Medium: clean air
Supply pressure: 5.5 barg ~ 80psig
Load: with average load
Stroke: 90°
Temperature: Room temperature
P
9.05
0.2 - 8
barg
Clean, dry or lubricated air or
inert gas.
Open 0.4
Sec.
G1/8" M6x12
Torque Output
Spring-return
Spring
set
2
Spring Stroke
Torque
Start
End
7.2
4.6
Double-acting
Air Stroke Torque (Nm)
3.0 barg
3.5 barg
4.0 barg
4.5 barg
5.0 barg
5.5 barg
6.0 barg
7.0 barg
8.0 barg
Start End Start End Start End Start End Start End Start End Start Start Start End Start End
-
-
3.8
7.3
1
8.5
5.1
2.3
6.4
9.7
3.6
11.0
7.7
4.9
12.2
9.0
6.2
13.4
10.3
7.5
12.9 10.1 15.6 12.8
14.6
17.1
19.6
„„Flange and square drive to ISO 5211
European Directives:
„„PED : suitable for use with group 2 gases according to
Pressure Equipment Directive 97/23/EC
„„Option: Solenoid mounting interface according to VDI/VDE
„„ATEX : suitable for use in hazardous areas classified as II 2 GD,
Notes:
„„Volume is the actual free air volume at 1 atm
3845 (NAMUR). See dotted image.
zones 1 or 2 (gases) and 21 or 22 (dust).
„„For further information regarding options, materials,
certifications and additional execution please contact your
regional sales office
21
EL-O-Matic F-Series
Product Data Sheet
May 2015
EFM.04.01.EN, Page 1 of 2, Rev. 3
Dimensions - Metric (ISO5211)
Envelope dimensions - Solenoid interface - Top mounting interface
Solenoid interface
A2 (DA)
Top mounting interface
C2
C1
C3
2x
1/4” BSP
4
32
Note 3
A3
4
C5
A4
24
C4
4X
M5x8
A8
A9
B3
4x
M5x8
M6x12
Note 3
30
B1
A7
A1 (SR)
A5
B2
A6
Tolerance limits unless
otherwise specified:
X.
= ± 0.5 mm
X.X
= ± 0.25 mm
X.XX = ± 0.1 mm
Note:
1. DA = Double-Acting, SR = Spring-Return
2. Solenoid interface and top mounting interface according to VDI/VDE3845 (NAMUR)
3. The solenoid drilling pattern is shifted 4 mm for size 0025 and 2 mm for size 0040 vs
the centerline of the actuator.
Dim. in
mm
0025
0040
0065
0100
0150
0600
0950
1600
2500
4000
A1
166
192
217
247
304
362
385
476
xxx
xxx
xxx
xxx
A2
166
192
217
247
223
256
269
336
xxx
xxx
xxx
xxx
A3
91
112
124
131
157
163
201
248
xxx
xxx
xxx
xxx
A4
119
139
151
158
185
191
230
292
xxx
xxx
xxx
xxx
A5
82
95
104
115
127
134
165
199
xxx
xxx
xxx
xxx
A6
49
55
58
64
69
72
85
102
xxx
xxx
xxx
xxx
A7
30
34
38
38
49
49
42
67
xxx
xxx
xxx
xxx
A8
48
58
69
69
75
87
109
132
xxx
xxx
xxx
xxx
A9
18
25
27
28
46
46
46
60
xxx
xxx
xxx
xxx
B1
43
45
50
60
75
75
85
98
xxx
xxx
xxx
xxx
B2
94
94
94
97
94
94
100
148
xxx
xxx
xxx
xxx
B3
80
80
80
80
80
80
80
130
130
130
130
130
C1
16
22
22
22
34
36
36
55
55
64
55
64
C2
23
30
30
30
45
45
45
65
65
75
65
80
C3
10
14
14
14
19
19
19
36
36
36
36
36
C4
20
20
20
20
20
20
20
30
30
30
30
30
C5
12
12
12
12
12
12
12
10
10
10
10
10
22
Actuator size
0200
0350
Product Data Sheet
EL-O-Matic F-Series
EFM.04.01.EN, Page 2 of 2, Rev. 3
May 2015
Dimensions - Metric (ISO5211)
Valve Flange and Drive details
Size 25
to 950
Size 1600
& 2500
øD1
øD3
D6
4x D4
Note:
1. Flange and square drive
according to ISO 5211
234.6
D6
97.2
4x D2
E4
D5
4x
M16x25
D5
øE5
øD1
øD3
Size
4000
E3
Tolerance limits unless
otherwise specified:
X.
=
± 0.5 mm
X.X
=
± 0.25 mm
X.XX =
± 0.1 mm
E7 ±0.5
øE6
D6
øE2
262
+0.5
0
E1
4x D2
4x D4
Dim in.
mm
0025
0040
0065
0100
0150
Actuator size
0200
0350
0600
0950
1600
2500
ISO 1
F05
F07
F07
F07
F10
F10
F10
F12
F14
F16
F16
F25
D1
50
70
70
70
102
102
102
125
125
165
165
254
M16x25
4000
D2
M6x10
M8x13
M8x13
M8x13
M10x15
M10x15
M10x15
M12x18
M12x18
M20x20
M20x20
ISO 2
F03
F05
F05
F05
F07
F07
F07
F10
F10
F25*
F25*
F16
D3
36
50
50
50
70
70
70
102
102
-/-
-/-
165
D4
M5x8
M6x10
M6x10
M6x10
M8x13
M8x13
M8x13
M10x16
M10x16
-/-
-/-
M20x20
D5
50
68
68
66
97
94
94
118
xx.x
xx.x
xx.x
xx.x
D6
48
65
65
63
92
90
94
113
xx.x
xx.x
xx.x
xx.x
E1 Max
11.08
14.08
14.08
19.08
19.08
22.10
27.11
27.11
36.16
46.16
46.16
55.24
E1 Min
11.00
14.00
14.00
19.00
19.00
22.00
27.00
27.00
36.00
46.00
46.00
55.00
E2
14.1
18.1
18.1
25.2
25.5
28.2
36.2
36.21
58.2
60.2
60.2
72.2
E3
15
15
15
18
27.5
27.5
27.5
27.5
xx.x
xx.x
xx.x
xx.x
E4
34
34
34
34
50
50
50
50
xx.x
xx.x
xx.x
xx.x
E5
14.1
18.1
21.1
23.5
28.5
32.1
32.1
36.5
xx.x
xx.x
xx.x
xx.x
E6
24.5
34.5
34.5
38
56.5
56.5
56.5
67.5
xx.x
xx.x
xx.x
xx.x
E7
0.5
1
1
1
1.2
1.2
1.2
1.2
x.x
x.x
x.x
x.x
23
EL-O-Matic F-Series
Product Data Sheet
May 2015
EFD.04.01.EN Page 1 of 2, Rev. 3
Dimensions - Metric (DIN3337)
Envelope dimensions - Solenoid interface - Top mounting interface
A2 (DA)
C2
C1
C3
2x
G1/4”
4
32
Note 3
A3
4
C5
A4
24
C4
4X
M5x8
A8
A9
B3
4x
M5x8
Note 3
M6x12
30
B1
A7
A1 (SR)
A5
B2
A6
Tolerance limits unless
otherwise specified:
X.
=
± 0.5 mm
X.X
=
± 0.25 mm
X.XX =
± 0.1 mm
Note:
1. DA = Double-Acting, SR = Spring-Return
2. Solenoid interface and top mounting interface according to VDI/VDE3845 (NAMUR)
3. The solenoid drilling pattern is shifted 4 mm for size 0025 and 2 mm for size 0040 vs
the centerline of the actuator.
Dim. in
mm
0025
0040
0065
0100
0150
0600
0950
1600
2500
4000
A1
166
192
217
247
304
362
385
476
xxx
xxx
xxx
xxx
A2
166
192
217
247
223
256
269
336
xxx
xxx
xxx
xxx
A3
91
112
124
131
157
163
201
248
xxx
xxx
xxx
xxx
A4
119
139
151
158
185
191
230
292
xxx
xxx
xxx
xxx
A5
82
95
104
115
127
134
165
199
xxx
xxx
xxx
xxx
A6
49
55
58
64
69
72
85
102
xxx
xxx
xxx
xxx
A7
30
34
38
38
49
49
42
67
xxx
xxx
xxx
xxx
A8
48
58
69
69
75
87
109
132
xxx
xxx
xxx
xxx
A9
18
25
27
28
46
46
46
60
xxx
xxx
xxx
xxx
B1
43
45
50
60
75
75
85
98
xxx
xxx
xxx
xxx
B2
94
94
94
97
94
94
100
148
xxx
xxx
xxx
xxx
B3
80
80
80
80
80
80
80
130
130
130
130
130
C1
16
22
22
22
34
36
36
55
55
64
55
64
C2
23
30
30
30
45
45
45
65
65
75
65
80
C3
10
14
14
14
19
19
19
36
36
36
36
36
C4
20
20
20
20
20
20
20
30
30
30
30
30
C5
12
12
12
12
12
12
12
10
10
10
10
10
24
Actuator size
0200
0350
Product Data Sheet
EL-O-Matic F-Series
EFD.04.01.EN Page 2 of 2, Rev. 3
May 2015
Dimensions - Metric (DIN3337)
Valve Flange and Drive details
Size
25 to
950
Size 1600
& 2500
øD5
øD1
Note:
1. Flange and square drive
according to DIN 3337
234.6
2. Drilling pattern DIN 1 is
default. Drilling pattern
DIN 2 is optional.
D10
4x D2
D6
97.2
4x D6
D5
4x
M16x25
D9
øE6
øE5
D5
øD1
øD3
Size
4000
E7
E3
±0.5
Tolerance limits unless
otherwise specified:
X.
=
± 0.5 mm
X.X
=
± 0.25 mm
X.XX =
± 0.1 mm
E4
E8
D4 (D8)
D3 (D7)
2
D6 262
E1
4x D2
øE2+0.5
0
4x D6
Dim in.
mm
0025
0040
0065
0100
0150
Actuator size
0200
0350
0600
0950
1600
2500
DIN 1
F05
F05
F05
F07
F07
F10
F10
F12
F14
F16
F16
F25
D1
50
50
50
70
70
102
102
125
125
165
165
254
D2
M6x10
M6x10
M6x10
M8x13
M8x13
M10x15
M10x15
M12x18
M12x18
M20x20
M20x20
M16x25
D3
35
35
35
55
55
70
70
85
100
130
130
200
D4
29
32
32
40
50
54
54
68
75
95
95
120
DIN 2
F03
F07
F07
F05
F10
F07
F07
F10
F10
-/-
-/-
-/-
D5
36
70
70
50
102
70
70
102
102
-/-
-/-
-/-
D6
M5x8
M8x13
M8x13
M6x10
M10x15
M8x13
M8x13
M10x15
M10x15
-/-
-/-
-/-
D7
-
40
40
32
54
50
50
-/-
-/-
-/-
-/-
-/-
4000
D8
-
55
55
35
70
55
55
-/-
-/-
-/-
-/-
-/-
D9
50
68
68
66
97
94
94
118
xx.x
xx.x
xx.x
xx.x
D10
48
65
65
63
92
90
94
113
xx.x
xx.x
xx.x
xx.x
E1 Max.
11
14
14
17
17
22
22
27
36.16
46.16
46.16
55.24
E1 Min.
11
14
14
17
17
22
22
27
36
46
46
55
E2
14
18
18
25
26
28
36
36
58.2
60.2
60.2
72.2
E3
15
15
15
18
28
28
28
28
xx.x
xx.x
xx.x
xx.x
E4
34
34
34
34
50
50
50
50
xx.x
xx.x
xx.x
xx.x
E5
14
18
21
24
29
32
32
37
xx.x
xx.x
xx.x
xx.x
E6
25
35
35
38
57
57
57
68
xx.x
xx.x
xx.x
xx.x
E7
1
1
1
1
1
1
1
1
x.x
x.x
x.x
x.x
E8
5
5
5
5
5
5
5
5
6
7
?
?
25
EL-O-Matic F-Series
Product Data Sheet
May 2014
EFI.04.01.EN, Page 1 of 2, Rev. 2
Dimensions - Imperial (ISO5211)
Envelope dimensions - Solenoid interface - Top mounting interface
A2 (DA)
C2
C1
C3
2x
1/4” NPT
0.16
1.26”
Note 3
A3
0.16
C5
A4
0.95”
C4
4X
UNC 10-24
x0.31
A8
A9
B3
M6x0.47”
Note 3
1.181”
A7
A1 (SR)
B1
4X
UNC 10-24
x0.31
A5
B2
A6
Tolerance limits unless
otherwise specified:
X.X
=
± 0.02"
X.XX =
± 0.01"
Note:
1. DA = Double-Acting, SR = Spring-Return
2. Solenoid interface and top mounting interface according to VDI/VDE3845 (NAMUR)
3. The solenoid drilling pattern is shifted 0.16” for size 0025 and 0.08” for size 0040 vs.
the centerline of the actuator.
Dim in.
Inches
0025
0040
0065
0100
0150
Actuator size
0200
0350
0600
0950
1600
2500
4000
A1
6.54
7.55
8.53
9.72
11.97
14.23
15.15
18.73
xx.xx
xx.xx
xx.xx
xx.xx
A2
6.54
7.55
8.53
9.72
8.80
10.07
10.58
13.21
xx.xx
xx.xx
xx.xx
xx.xx
A3
3.59
4.39
4.86
5.14
6.19
6.42
7.92
9.77
xx.xx
xx.xx
xx.xx
xx.xx
xx.xx
26
A4
4.69
5.47
5.94
6.22
7.28
7.52
9.06
11.50
xx.xx
xx.xx
xx.xx
A5
3.23
3.74
4.09
4.53
5.00
5.28
6.50
7.83
xx.xx
xx.xx
xx.xx
xx.xx
A6
1.91
2.15
2.28
2.50
2.72
2.83
3.35
4.02
xx.xx
xx.xx
xx.xx
xx.xx
A7
1.16
1.34
1.48
1.50
1.93
1.92
1.65
2.64
xx.xx
xx.xx
xx.xx
xx.xx
A8
1.89
2.28
2.72
2.72
2.95
3.43
4.29
5.20
xx.xx
xx.xx
xx.xx
xx.xx
A9
0.71
0.98
1.06
1.10
1.81
1.81
1.81
2.36
xx.xx
xx.xx
xx.xx
xx.xx
B1
1.69
1.77
1.97
2.36
2.95
2.95
3.35
3.86
xx.xx
xx.xx
xx.xx
xx.xx
B2
3.70
3.70
3.70
3.82
3.70
3.70
3.94
5.83
xx.xx
xx.xx
xx.xx
xx.xx
5.12
B3
3.15
3.15
3.15
3.15
3.15
3.15
3.15
5.12
5.12
5.12
5.12
C1
0.63
0.87
0.87
0.87
1.34
1.42
1.42
2.17
2.17
2.52
2.17
2.52
C2
0.91
1.18
1.18
1.18
1.77
1.77
1.77
2.56
2.56
2.95
2.56
3.15
C3
0.39
0.55
0.55
0.55
0.75
0.75
0.75
1.42
1.42
1.42
1.42
1.42
C4
0.79
0.79
0.79
0.79
0.79
0.79
0.79
1.18
1.18
1.18
1.18
1.18
C5
0.47
0.47
0.47
0.47
0.47
0.47
0.47
0.39
0.39
0.39
0.39
0.39
Product Data Sheet
EL-O-Matic F-Series
EFI.04.01.EN, Page 2 of 2, Rev. 2
May 2014
Dimensions - Imperial (ISO5211)
Valve Flange and Drive details
Size
25 to
950
Size 1600
& 2500
øD1
øD3
Note:
1. Flange and square drive
according to DIN 3337
9.236”
2. Drilling pattern DIN 1 is
default. Drilling pattern
DIN 2 is optional.
D6
4x D4
D6
3.827”
Tolerance limits unless
otherwise specified:
X.X
=
± 0.02"
X.XX =
± 0.01"
4x D2
D5
4x
5/8”-11
x 0.98”
D5
øE5
øD1
øD3
Size
4000
E4
E3
E7 ±0.02
øE6
10.3”
D6
øE2
+0.02
0
E1
4x D2
4x D4
Dim in.
Inches
0025
0040
0065
0100
0150
ISO 1
F05
F07
F07
F07
F10
D1
D2
ISO 2
Actuator size
0200
0350
0600
0950
1600
2500
F10
F10
F12
F14
F16
F16
F25
4.016
"3/8""-16
x0.63"
F07
4.016
"3/8""-16
x0.63"
F07
4.921
"1/2""-13
x0.79"
F10
4.921
"5/8""-11
x0.98"
F10
6.496
6.496
-/-
-/-
F25*
F25*
10.000
"5/8""-11
x0.98"
F16
1.969
2.756
2.756
2.756
4.016
"1/4""-20 "5/16""-18 "5/16""-18 "5/16""-18 "3/8""-16
x0.39"
x0.39"
x0.39"
x0.39"
x0.63"
2.62
3.82
3.7
3.7
4.65
4.016
"3/8""-16
x0.63"
xx.x
-/-
-/-
-/-
-/-
xx.x
xx.x
1.969
2.756
2.756
2.756
4.016
"1/4""-20 "5/16""-18 "5/16""-18 "5/16""-18 "3/8""-16
x0.39"
x0.39"
x0.39"
x0.39"
x0.63"
F03
F05
F05
F05
F07
4000
D5
1.417
"10-24
x0.31"
1.97
1.969
"1/4""-20
x0.39"
2.68
1.969
"1/4""-20
x0.39"
2.68
D6
1.89
2.56
2.56
2.48
3.62
3.54
3.7
4.45
xx.x
xx.x
xx.x
xx.x
E1 Max
0.436
0.554
0.554
0.751
0.751
0.87
1.067
1.067
1.424
1.817
1.817
2.175
E1 Min
0.433
0.551
0.551
0.748
0.748
0.866
1.063
1.063
1.417
1.811
1.811
2.165
E2
0.555
0.713
0.713
0.992
1.004
1.11
1.425
1.426
2.291
2.37
2.37
2.843
E3
0.591
0.591
0.591
0.709
1.083
1.083
1.083
1.083
xx.x
xx.x
xx.x
xx.x
E4
1.34
1.34
1.34
1.34
1.97
1.97
1.97
1.97
xx.x
xx.x
xx.x
xx.x
E5
0.56
0.71
0.83
0.93
1.12
1.26
1.26
1.44
xx.x
xx.x
xx.x
xx.x
E6
0.96
1.36
1.36
1.5
2.22
2.22
2.22
2.66
x.xxx
x.xxx
x.xxx
x.xxx
E7
0.02
0.04
0.04
0.04
0.05
0.05
0.05
0.05
x.xx
x.xx
x.xx
x.xx
D3
D4
6.496
"3/4""-10
x1.14"
xx.x
27
EL-O-Matic F-Series
Product Data Sheet
March 2014
EFG.05.01.EN, Page 1 of 2, Rev. 0
Drive Inserts
Description
Drive inserts can be supplied on factory built actuators or as loose
items and are easily replaceable at distributor or end user level.
The EL-O-Matic F actuators are fitted with drive inserts.
These drive inserts allow actuators to be directly mounted
onto suitable valves and eliminates the need for a bracket
and coupling type mounting kit. The use of direct mounts
significantly cuts the cost of the valve/actuator assembly.
Where direct mounts are not possible, for instance on valves
with exposed grand packing, the use of inserts often simplifies
the design of the mounting kit.
Standard actuators are fitted with square drive inserts in
accordance with ISO 5211. The ISO 5211 covers now parallel and
diagonal oriented inner squares (as per old DIN 3337 standard).
A wide variety of other inserts are also available. Special inserts
may have oversized or undersized squares, double-D and shaft
key way forms.
„„Material: Aluminium alloy
„„Finish : Anodized
Note:
Size D12 does not have inserts. This actuator have the inner
square directly in the bottom of the pinion.
Table 1. Inserts with inner-square-dimensions per actuator size (metric)
Inserts with inner-square-dimensions per actuator type
F0040/
F0025
F0100
F0150
F0200
F0350
F0065
Standard square insert dimensions
11
14
19
19
22
27
Parallel:
11
14
17
17
22
22
Diagonal:
Optional square insert dimensions
9
10
12
14
14
14
10
12
14
16
16
16
16
22
17
17
24
19
19
27
24
24
Maximum insert dimensions
M1
34.5
34.5
34.5
50
50
50
M2
27
37
37
P1
14.1
18.1
23.1
28.5
32.1
32.1
P2
25.2
36.2
36.2
Sq. max.
11
16
19
27
27
27
D max.
13.8
21
23.6
33.6
33.6
33.6
Dim. in mm
F0600
F0950
F1600
F2500
F4000
27
27
36
36
46
46
46
46
55
55
14
16
17
19
24
22
-
-
-
??
??
??
??
??
52
36.5
27
33.6
64
48.5
36
45
82
60.5
46
60
82
60.5
46
60
??
??
??
??
??
??
- Parallel Insert
Standard available
insert shapes
sq
Max.
Optional available
insert shapes
D
Max.
M1 M2
- Diagonal insert
mounting
mounting
Ø P2
Ø P1
Ø P2
Ø P1
M1 M2
Center plate
D
Max.
28
Product Data Sheet
EL-O-Matic F-Series
EFG.05.01.EN, Page 2 of 2, Rev. 0
March 2014
Table 2. Inserts with inner-square-dimensions per actuator size (Imperial)
Dim. In
inches
Inserts with inner-square-dimensions per actuator type
F0040/
F0025
F0100
F0150
F0200
F0350
F0065
F0600
F0950
F1600
F2500
F4000
Standard square insert dimensions
0.433
0.551
0.748
Parallel:
0.748
0.866
1.063
1.063
1.417
1.811
1.811
2.165
Optional square insert dimensions
0.354
0.394
0.472
0.394
0.472
0.551
0.630
-
0.551
0.630
0.866
0.945
1.063
0.551
0.630
0.669
0.748
0.945
0.551
0.630
0.669
0.748
0.945
0.551
0.630
0.669
0.748
0.945
0.866
-
-
-
??
??
??
??
??
Maximum insert dimensions
M1
1.358
1.358
M2
P1
0.555
0.713
P2
Sq. max.
0.433
0.630
D max.
0.543
0.827
1.969
1.122
1.063
1.323
1.969
1.457
1.264
1.425
1.063
1.323
1.969
1.457
1.264
1.425
1.063
1.323
2.047
1.437
1.063
1.323
2.520
1.909
1.417
1.772
3.228
2.382
1.811
2.362
3.228
2.382
1.811
2.362
??
??
??
??
??
??
1.358
1.063
0.909
0.992
0.748
0.929
- Parallel Insert
mounting
Standard available
insert shapes
Optional available
insert shapes
Ø P2
Ø P1
sq
Max.
D
Max.
M1 M2
D
Max.
29
EL-O-Matic F-Series
Product Data Sheet
March 2014
EFG.05.02.EN Rev. 0
Centering Plate
EL-O-Matic F actuators can be equipped with a centering plate
which takes care that actuator and valve (or valve mounting kit)
are aligned when mounted. For most of the actuator sizes two
centering plates are available.
„„Specifications:
——Material plate:
Nylon PA6, Black
Centering plate
ELOMATIC F actuator models
F 25
F 40
F 65
F 100
F 150
F 200
F 350
F 600
F 950
F 1600
F 2500
F 4000
Default*
F05
F05
F05
F07
F07
F10
F10
F12
F14
F16
F16
F25
Option
-/-
F07
F07
F05
F10
F07
F07
F10
-/-
-/-
-/-
-/-
1. * Default selection if actuator needs to comply to DIN 3337, see dimension sheet EFD.04.01.EN.
30
Product Data Sheet
EL-O-Matic F-Series
EFG.05.03.EN Rev. 0
March 2014
Visual indicator EL-O-Matic F-Series actuators
Description
EL-O-Matic F-Series actuators have a large visual position
indicator which allows clear indication of the valve's position at
almost any position.
Indicator mounting "In line"
EL-O-Matic F-Series indicator is designed for position indication
of actuators mounted “in line” with the pipe line and mounted
“cross line” with the pipe line.
Conversion is easily done by turning the indicator 90° and
reassemble back in place.
Default, the position indicator will be mounted “in line”.
Specifications:
Materials:
„„Indicator knob: ABS, Black
„„Indicator arrow:
ABS, White
„„Indicator screw:
SS Head cap screw M6x12
Indicator mounting "Across line"
31
EL-O-Matic F-Series
Product Data Sheet
March 2014
EFG.05.05.EN Rev. 0
High Temperature Execution
Description
A double piston, rack and pinion pneumatic actuator,
incorporating an anti-blowout pinion and a piston support
system with high duty synthetic bearings at all bearing points.
This version is a standard aluminum actuator, but incorporating
grease, O-ring seal and bearing materials, suitable for high
temperature operation up to 248°F (120°C).
Specification
Max. pressure:
Torque:
Media:
Temperature:
Finish:
120 psig (8.3 barg)
Standard
Air or non corrosive gas
-4°F to +248°F (-20°C to +120°C)
Polyurethane powder coating
(see data sheet EFG.01.03.EN)
Spare parts
Dedicated high temperature spare part kits are available for
maintenance or to convert a standard actuator into a version
suitable for high temperature operation.
Description
House
End cap
Piston
Pinion
Spring cartridge
Bearing strip piston rack
Bearing piston
Bearing pinion
Thrust washer
End cap screw
Circlip
O-ring seal pinion
O-ring seal piston
O-ring seal end cap
O-ring seal limit stop
B-port seal
Limit stop screw
Limit stop nut
Limit stop washer
Warning sticker
Indicator assembly
Center plate (option)
Insert drive
Grease
32
Material
Cast Aluminium alloy
Cast Aluminium alloy
Cast Aluminium alloy
High grade aluminium
Spring steel
Nylon 66 resin containing Aramid Fibre & PTFE
PTFE 25% carbon filled
Nylon 66 resin containing Aramid Fibre & PTFE
POM, black UV stabilized
Stainless Steel
Spring steel
Viton FPM
Viton FPM
Viton FPM
Viton FPM
Silicon rubber
Stainless steel
Stainless steel
PA66
Polyester
ABS + stainless steel screw
Nylon PA6, Black
Aluminium alloy
Castrol High temperature grease
High temperature components:
- Castrol High temperature grease
- Viton (FPM) O-ring seals
- PTFE 25% carbon filled piston bearings
- Nylon 66 resin containing Aramid Fibre &
PTFE for bearing strip piston rack and
pinion bearings.
Product Data Sheet
EL-O-Matic F-Series
EFG.05.06.EN Rev. 0
March 2014
Low Temperature Execution
Description
A double piston, rack and pinion pneumatic actuator,
incorporating an anti-blowout pinion and a piston support
system with high duty synthetic bearings at all bearing points.
Low temperature components:
- Castrol Optitemp TT1 grease
- Silicone (MVQ70 rubber) O-ring seals
This version is a standard aluminum actuator, but incorporating
grease and O-ring seal materials, suitable for low temperature
operation down to -40°F (-40°C).
Note:
When operating actuators in sub-zero temperatures (< 0°C or
< 32°F) care should be taken to counter the effects of freezing
condensate inside the actuator.
Specification
Max. pressure:
Torque:
Media:
Temperature:
Finish:
120 psig (8.3 barg)
Standard
Air or non corrosive gas
-40°C to +80°C (-40°F to +176°F)
Polyurethane powder coating
(see data sheet EFG.01.03.EN)
Spare parts
Dedicated low temperature spare part kits are available for
maintenance or to convert a standard actuator in to a version
suitable for low temperature operation.
Description
House
End cap
Piston
Pinion
Spring cartridge
Bearing strip piston rack
Bearing piston
Bearing pinion
Thrust washer
End cap screw
Circlip
O-ring seal pinion
O-ring seal piston
O-ring seal end cap
O-ring seal limit stop
B-port seal
Limit stop screw
Limit stop nut
Limit stop washer
Warning sticker
Indicator assembly
Center plate (option)
Insert drive
Grease
Material
Cast Aluminium alloy
Cast Aluminium alloy
Cast Aluminium alloy
High grade aluminium
Spring steel
POM
PTFE 25% carbon filled
POM
POM, black UV stabilized
Stainless Steel
Spring steel
Silicone MVQ70
Silicone MVQ70
Silicone MVQ70
Silicone MVQ70
Silicon rubber
Stainless steel
Stainless steel
PA66
Polyester
ABS + stainless steel screw
Nylon PA6, Black
Aluminium alloy
Castrol Optitemp TT1 grease
33
World Area Configuration Centers (WACC) offer sales support,
service, inventory and commissioning to our global customers.
Choose the WACC or sales office nearest you:
NORTH & SOUTH AMERICA
MIDDLE EAST & AFRICA
19200 Northwest Freeway
Houston, TX 77065
T +1 281 477 4100
F +1 281 477 2809
P. O. Box 17033
Dubai
United Arab Emirates
T +971 4 811 8100
F +971 4 886 5465
Av. Hollingsworth,
325, Iporanga Sorocaba,
SP 18087-105
Brazil
T +55 15 3238 3788
F +55 15 3228 3300
ASIA PACIFIC
No. 9 Gul Road
#01-02 Singapore 629361
T +65 6501 4600
F +65 6268 0028
No.1 Lai Yuan Road
Wuqing Development Area
Tianjin 301700
P.R.China
T +86 22 8212 3300
F +86 22 8212 3308
P. O. Box 10305
Jubail 31961
Saudi Arabia
T +966 3 340 8650
F +966 3 340 8790
24 Angus Crescent
Longmeadow Business Estate
East P.O. Box 6908; Greenstone;
1616 Modderfontein, Extension 5
South Africa
T +27 11 451 3700
F +27 11 451 3800
EUROPE
Asveldweg 11
7556 BR Hengelo (O)
The Netherlands
T +31 74 256 1010
F +31 74 291 0938
For complete list of sales and manufacturing sites, please visit
www.emersonprocess.com/valveautomationlocations
Or contact us at [email protected]
EL
Matic TM
www.emersonprocess.com/elomatic
All Rights Reserved.
We reserve the right to modify or improve the designs or specifications
of the products mentioned in this manual at any time without notice.
Emerson Process Management does not assume responsibility for the
selection, use or maintenance of any product. Responsibility for proper
selection, use and maintenance of any Emerson Process Management
product remains solely with the purchaser.
©2014 Emerson Electric Co.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement