HP ProLiant DL560 Specifications

HP ProLiant DL560 Specifications
HP ProLiant DL560 Gen8 Server
Maintenance and Service Guide
Abstract
This guide describes identification and maintenance procedures, diagnostic tools, specifications, and requirements for hardware components and
software. This guide is for an experienced service technician. HP assumes you are qualified in the servicing of computer equipment, trained in
recognizing hazards in products, and are familiar with weight and stability precautions.
Part Number: 696743-003
February 2014
Edition: 3
© Copyright 2012, 2014 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation. Intel® and Xeon® are trademarks of Intel Corporation in the
United States and other countries.
Contents
Customer self repair ...................................................................................................................... 5
Parts only warranty service ......................................................................................................................... 5
Illustrated parts catalog ............................................................................................................... 15
Mechanical components........................................................................................................................... 15
System components ................................................................................................................................. 18
Removal and replacement procedures ........................................................................................... 23
Required tools ......................................................................................................................................... 23
Safety considerations ............................................................................................................................... 23
Preventing electrostatic discharge .................................................................................................... 23
Symbols on equipment ................................................................................................................... 23
Server warnings and cautions ......................................................................................................... 24
Preparation procedures ............................................................................................................................ 24
Power down the server ................................................................................................................... 25
Extend the server from the rack........................................................................................................ 25
Remove the server from the rack ...................................................................................................... 26
Access the Systems Insight Display ................................................................................................... 27
Access the product rear panel ......................................................................................................... 27
Release the full-length expansion board retainer ................................................................................ 28
Access panel .......................................................................................................................................... 29
Air baffle ............................................................................................................................................... 29
2U rack bezel ......................................................................................................................................... 30
PCIe riser blank....................................................................................................................................... 31
PCIe riser cage (primary) .......................................................................................................................... 31
PCIe riser cage (secondary) ...................................................................................................................... 32
PCIe riser board ...................................................................................................................................... 33
Drive blank ............................................................................................................................................. 34
Hot-plug drive ......................................................................................................................................... 34
Power supply blank ................................................................................................................................. 35
AC power supply .................................................................................................................................... 35
Power supply backplane .......................................................................................................................... 36
Hot-plug fan ........................................................................................................................................... 37
FlexibleLOM ........................................................................................................................................... 38
Front panel assembly ............................................................................................................................... 40
Flash-backed write cache procedures ......................................................................................................... 41
Flash-backed write cache module .................................................................................................... 41
Flash-backed write cache capacitor pack.......................................................................................... 43
Recovering data from the flash-backed write cache ............................................................................ 45
Expansion slot blanks............................................................................................................................... 46
Expansion boards ................................................................................................................................... 47
Half-length expansion board ........................................................................................................... 47
Full length expansion board ............................................................................................................ 47
Heatsink ................................................................................................................................................. 48
Processor ............................................................................................................................................... 51
DIMMs................................................................................................................................................... 55
System battery ........................................................................................................................................ 56
Contents
3
System board ......................................................................................................................................... 57
150W PCIe power cable option ............................................................................................................... 63
HP Trusted Platform Module ...................................................................................................................... 63
Cabling ..................................................................................................................................... 64
SAS drive cabling ................................................................................................................................... 64
FBWC cabling ........................................................................................................................................ 65
Diagnostic tools .......................................................................................................................... 66
Troubleshooting resources ........................................................................................................................ 66
HP Insight Diagnostics .............................................................................................................................. 66
HP Insight Diagnostics survey functionality ........................................................................................ 67
HP ROM-Based Setup Utility ..................................................................................................................... 67
Integrated Management Log ..................................................................................................................... 67
USB support and functionality ................................................................................................................... 68
USB support .................................................................................................................................. 68
Internal USB functionality ................................................................................................................ 68
External USB functionality ............................................................................................................... 68
Component identification ............................................................................................................. 69
Front panel components ........................................................................................................................... 69
Front panel LEDs and buttons .................................................................................................................... 69
Systems Insight Display LEDs ..................................................................................................................... 70
Systems Insight Display LED combinations ................................................................................................... 71
Rear panel components ............................................................................................................................ 72
Rear panel LEDs and buttons ..................................................................................................................... 73
Non-hot-plug PCIe riser board slot definitions .............................................................................................. 73
System board components ........................................................................................................................ 74
System maintenance switch ............................................................................................................. 75
NMI functionality ........................................................................................................................... 76
DIMM slot locations ....................................................................................................................... 77
Hot-plug drive bay numbering ................................................................................................................... 77
Hot-plug drive LED definitions.................................................................................................................... 77
PCIe riser cage LED ................................................................................................................................. 78
FBWC module LEDs (P222, P420, P421) ................................................................................................... 79
Hot-plug fans .......................................................................................................................................... 79
Storage and expansion diagram ............................................................................................................... 81
Specifications ............................................................................................................................. 82
Environmental specifications ..................................................................................................................... 82
Mechanical specifications ........................................................................................................................ 82
Power supply specifications ...................................................................................................................... 82
HP 1200 W CS HE Power Supply (94%) specifications ...................................................................... 82
Acronyms and abbreviations ........................................................................................................ 84
Documentation feedback ............................................................................................................. 86
Index ......................................................................................................................................... 87
Contents
4
Customer self repair
HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow for
greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP service
providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will
ship that part directly to you for replacement. There are two categories of CSR parts:
•
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts,
you will be charged for the travel and labor costs of this service.
•
Optional—Parts for which customer self repair is optional. These parts are also designed for customer
self repair. If, however, you require that HP replace them for you, there may or may not be additional
charges, depending on the type of warranty service designated for your product.
NOTE: Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty,
HP requires that an authorized service provider replace the part. These parts are identified as "No" in the
Illustrated Parts Catalog.
Based on availability and where geography permits, CSR parts will be shipped for next business day
delivery. Same day or four-hour delivery may be offered at an additional charge where geography permits.
If assistance is required, you can call the HP Technical Support Center and a technician will help you over the
telephone. HP specifies in the materials shipped with a replacement CSR part whether a defective part must
be returned to HP. In cases where it is required to return the defective part to HP, you must ship the defective
part back to HP within a defined period of time, normally five (5) business days. The defective part must be
returned with the associated documentation in the provided shipping material. Failure to return the defective
part may result in HP billing you for the replacement. With a customer self repair, HP will pay all shipping
and part return costs and determine the courier/carrier to be used.
For more information about HP's Customer Self Repair program, contact your local service provider. For the
North American program, refer to the HP website (http://www.hp.com/go/selfrepair).
Parts only warranty service
Your HP Limited Warranty may include a parts only warranty service. Under the terms of parts only warranty
service, HP will provide replacement parts free of charge.
For parts only warranty service, CSR part replacement is mandatory. If you request HP to replace these parts,
you will be charged for the travel and labor costs of this service.
Réparation par le client (CSR)
Les produits HP comportent de nombreuses pièces CSR (Customer Self Repair = réparation par le client) afin
de minimiser les délais de réparation et faciliter le remplacement des pièces défectueuses. Si pendant la
période de diagnostic, HP (ou ses partenaires ou mainteneurs agréés) détermine que la réparation peut être
effectuée à l'aide d'une pièce CSR, HP vous l'envoie directement. Il existe deux catégories de pièces CSR:
Customer self repair 5
Obligatoire - Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de
remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
Facultatif - Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également
conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous demandez à HP de
remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type de garantie applicable à
votre produit.
REMARQUE: Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la
réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit effectué
par un Mainteneur Agréé. Ces pièces sont identifiées par la mention "Non" dans le Catalogue illustré.
Les pièces CSR sont livrées le jour ouvré suivant, dans la limite des stocks disponibles et selon votre situation
géographique. Si votre situation géographique le permet et que vous demandez une livraison le jour même
ou dans les 4 heures, celle-ci vous sera facturée. Pour bénéficier d'une assistance téléphonique, appelez le
Centre d'assistance technique HP. Dans les documents envoyés avec la pièce de rechange CSR, HP précise
s'il est nécessaire de lui retourner la pièce défectueuse. Si c'est le cas, vous devez le faire dans le délai
indiqué, généralement cinq (5) jours ouvrés. La pièce et sa documentation doivent être retournées dans
l'emballage fourni. Si vous ne retournez pas la pièce défectueuse, HP se réserve le droit de vous facturer les
coûts de remplacement. Dans le cas d'une pièce CSR, HP supporte l'ensemble des frais d'expédition et de
retour, et détermine la société de courses ou le transporteur à utiliser.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus
d'informations sur ce programme en Amérique du Nord, consultez le site Web HP
(http://www.hp.com/go/selfrepair).
Service de garantie "pièces seules"
Votre garantie limitée HP peut inclure un service de garantie "pièces seules". Dans ce cas, les pièces de
rechange fournies par HP ne sont pas facturées.
Dans le cadre de ce service, la réparation des pièces CSR par le client est obligatoire. Si vous demandez à
HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
Riparazione da parte del cliente
Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti
difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente
dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di servizi o di assistenza
HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo spedirà direttamente al cliente per
la sostituzione. Vi sono due categorie di parti CSR:
Obbligatorie – Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida la
riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio.
Opzionali – Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di componenti
progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP, potrebbe dover sostenere
spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
NOTA: alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare la
garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti sono
identificate da un "No" nel Catalogo illustrato dei componenti.
Customer self repair 6
In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro il
giorno lavorativo seguente. La consegna nel giorno stesso o entro quattro ore è offerta con un supplemento
di costo solo in alcune zone. In caso di necessità si può richiedere l'assistenza telefonica di un addetto del
centro di supporto tecnico HP. Nel materiale fornito con una parte di ricambio CSR, HP specifica se il cliente
deve restituire dei componenti. Qualora sia richiesta la resa ad HP del componente difettoso, lo si deve
spedire ad HP entro un determinato periodo di tempo, generalmente cinque (5) giorni lavorativi. Il
componente difettoso deve essere restituito con la documentazione associata nell'imballo di spedizione
fornito. La mancata restituzione del componente può comportare la fatturazione del ricambio da parte di HP.
Nel caso di riparazione da parte del cliente, HP sostiene tutte le spese di spedizione e resa e sceglie il
corriere/vettore da utilizzare.
Per ulteriori informazioni sul programma CSR di HP contattare il centro di assistenza di zona. Per il
programma in Nord America fare riferimento al sito Web HP (http://www.hp.com/go/selfrepair).
Servizio di garanzia per i soli componenti
La garanzia limitata HP può includere un servizio di garanzia per i soli componenti. Nei termini di garanzia
del servizio per i soli componenti, HP fornirà gratuitamente le parti di ricambio.
Per il servizio di garanzia per i soli componenti è obbligatoria la formula CSR che prevede la riparazione da
parte del cliente. Se il cliente invece richiede la sostituzione ad HP, dovrà sostenere le spese di spedizione
e di manodopera per il servizio.
Customer Self Repair
HP Produkte enthalten viele CSR-Teile (Customer Self Repair), um Reparaturzeiten zu minimieren und höhere
Flexibilität beim Austausch defekter Bauteile zu ermöglichen. Wenn HP (oder ein HP Servicepartner) bei der
Diagnose feststellt, dass das Produkt mithilfe eines CSR-Teils repariert werden kann, sendet Ihnen HP dieses
Bauteil zum Austausch direkt zu. CSR-Teile werden in zwei Kategorien unterteilt:
Zwingend – Teile, für die das Customer Self Repair-Verfahren zwingend vorgegeben ist. Wenn Sie den
Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und Arbeitskosten für diesen
Service berechnet.
Optional – Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für Customer
Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen lassen möchten,
können bei diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche
Kosten anfallen.
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog
sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert.
Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen einen
Aufpreis verfügbar. Wenn Sie Hilfe benötigen, können Sie das HP technische Support Center anrufen und
sich von einem Mitarbeiter per Telefon helfen lassen. Den Materialien, die mit einem CSR-Ersatzteil geliefert
werden, können Sie entnehmen, ob das defekte Teil an HP zurückgeschickt werden muss. Wenn es
erforderlich ist, das defekte Teil an HP zurückzuschicken, müssen Sie dies innerhalb eines vorgegebenen
Zeitraums tun, in der Regel innerhalb von fünf (5) Geschäftstagen. Das defekte Teil muss mit der zugehörigen
Dokumentation in der Verpackung zurückgeschickt werden, die im Lieferumfang enthalten ist. Wenn Sie das
Customer self repair 7
defekte Teil nicht zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung stellen. Im Falle von Customer
Self Repair kommt HP für alle Kosten für die Lieferung und Rücksendung auf und bestimmt den
Kurier-/Frachtdienst.
Weitere Informationen über das HP Customer Self Repair Programm erhalten Sie von Ihrem Servicepartner
vor Ort. Informationen über das CSR-Programm in Nordamerika finden Sie auf der HP Website unter
(http://www.hp.com/go/selfrepair).
Parts-only Warranty Service (Garantieservice
ausschließlich für Teile)
Ihre HP Garantie umfasst möglicherweise einen Parts-only Warranty Service (Garantieservice ausschließlich
für Teile). Gemäß den Bestimmungen des Parts-only Warranty Service stellt HP Ersatzteile kostenlos zur
Verfügung.
Für den Parts-only Warranty Service ist das CSR-Verfahren zwingend vorgegeben. Wenn Sie den Austausch
dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und Arbeitskosten für diesen Service
berechnet.
Reparaciones del propio cliente
Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar (Customer Self
Repair, CSR) para minimizar el tiempo de reparación y ofrecer una mayor flexibilidad a la hora de realizar
sustituciones de componentes defectuosos. Si, durante la fase de diagnóstico, HP (o los proveedores o socios
de servicio de HP) identifica que una reparación puede llevarse a cabo mediante el uso de un componente
CSR, HP le enviará dicho componente directamente para que realice su sustitución. Los componentes CSR se
clasifican en dos categorías:
•
Obligatorio: componentes para los que la reparación por parte del usuario es obligatoria. Si solicita a
HP que realice la sustitución de estos componentes, tendrá que hacerse cargo de los gastos de
desplazamiento y de mano de obra de dicho servicio.
•
Opcional: componentes para los que la reparación por parte del usuario es opcional. Estos
componentes también están diseñados para que puedan ser reparados por el usuario. Sin embargo, si
precisa que HP realice su sustitución, puede o no conllevar costes adicionales, dependiendo del tipo de
servicio de garantía correspondiente al producto.
NOTA: Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para que
el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios autorizado
realice la sustitución de estos componentes. Dichos componentes se identifican con la palabra "No" en el
catálogo ilustrado de componentes.
Según la disponibilidad y la situación geográfica, los componentes CSR se enviarán para que lleguen a su
destino al siguiente día laborable. Si la situación geográfica lo permite, se puede solicitar la entrega en el
mismo día o en cuatro horas con un coste adicional. Si precisa asistencia técnica, puede llamar al Centro de
asistencia técnica de HP y recibirá ayuda telefónica por parte de un técnico. Con el envío de materiales
para la sustitución de componentes CSR, HP especificará si los componentes defectuosos deberán
devolverse a HP. En aquellos casos en los que sea necesario devolver algún componente a HP, deberá
hacerlo en el periodo de tiempo especificado, normalmente cinco días laborables. Los componentes
defectuosos deberán devolverse con toda la documentación relacionada y con el embalaje de envío. Si no
Customer self repair 8
enviara el componente defectuoso requerido, HP podrá cobrarle por el de sustitución. En el caso de todas
sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de
componentes y escogerá la empresa de transporte que se utilice para dicho servicio.
Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en
contacto con su proveedor de servicios local. Si está interesado en el programa para Norteamérica, visite
la página web de HP siguiente (http://www.hp.com/go/selfrepair).
Servicio de garantía exclusivo de componentes
La garantía limitada de HP puede que incluya un servicio de garantía exclusivo de componentes. Según las
condiciones de este servicio exclusivo de componentes, HP le facilitará los componentes de repuesto sin
cargo adicional alguno.
Para este servicio de garantía exclusivo de componentes, es obligatoria la sustitución de componentes por
parte del usuario (CSR). Si solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse
cargo de los gastos de desplazamiento y de mano de obra de dicho servicio.
Customer Self Repair
Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot een
minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is. Deze
onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd. Als HP (of een HP Service Partner) bij
de diagnose vaststelt dat de reparatie kan worden uitgevoerd met een CSR-onderdeel, verzendt HP dat
onderdeel rechtstreeks naar u, zodat u het defecte onderdeel daarmee kunt vervangen. Er zijn twee
categorieën CSR-onderdelen:
Verplicht: Onderdelen waarvoor reparatie door de klant verplicht is. Als u HP verzoekt deze onderdelen
voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in rekening gebracht.
Optioneel: Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn ontworpen
voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen, kunnen
daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor het
product.
OPMERKING: Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband met
de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden vervangen.
Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee".
Afhankelijk van de leverbaarheid en de locatie worden CSR-onderdelen verzonden voor levering op de
eerstvolgende werkdag. Levering op dezelfde dag of binnen vier uur kan tegen meerkosten worden
aangeboden, indien dit mogelijk is gezien de locatie. Indien assistentie gewenst is, belt u een HP Service
Partner om via de telefoon technische ondersteuning te ontvangen. HP vermeldt in de documentatie bij het
vervangende CSR-onderdeel of het defecte onderdeel aan HP moet worden geretourneerd. Als het defecte
onderdeel aan HP moet worden teruggezonden, moet u het defecte onderdeel binnen een bepaalde
periode, gewoonlijk vijf (5) werkdagen, retourneren aan HP. Het defecte onderdeel moet met de
bijbehorende documentatie worden geretourneerd in het meegeleverde verpakkingsmateriaal. Als u het
defecte onderdeel niet terugzendt, kan HP u voor het vervangende onderdeel kosten in rekening brengen. Bij
reparatie door de klant betaalt HP alle verzendkosten voor het vervangende en geretourneerde onderdeel en
kiest HP zelf welke koerier/transportonderneming hiervoor wordt gebruikt.
Customer self repair 9
Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair programma
van HP. Informatie over Service Partners vindt u op de HP website (http://www.hp.com/go/selfrepair).
Garantieservice "Parts Only"
Het is mogelijk dat de HP garantie alleen de garantieservice "Parts Only" omvat. Volgens de bepalingen van
de Parts Only garantieservice zal HP kosteloos vervangende onderdelen ter beschikking stellen.
Voor de Parts Only garantieservice is vervanging door CSR-onderdelen verplicht. Als u HP verzoekt deze
onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in rekening
gebracht.
Reparo feito pelo cliente
Os produtos da HP são projetados com muitas peças para reparo feito pelo cliente (CSR) de modo a
minimizar o tempo de reparo e permitir maior flexibilidade na substituição de peças com defeito. Se,
durante o período de diagnóstico, a HP (ou fornecedores/parceiros de serviço da HP) concluir que o reparo
pode ser efetuado pelo uso de uma peça CSR, a peça de reposição será enviada diretamente ao cliente.
Existem duas categorias de peças CSR:
Obrigatória – Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas peças,
serão cobradas as despesas de transporte e mão-de-obra do serviço.
Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o
reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de
taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de
cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças estão
identificadas com a marca "No" (Não), no catálogo de peças ilustrado.
Conforme a disponibilidade e o local geográfico, as peças CSR serão enviadas no primeiro dia útil após o
pedido. Onde as condições geográficas permitirem, a entrega no mesmo dia ou em quatro horas pode ser
feita mediante uma taxa adicional. Se precisar de auxílio, entre em contato com o Centro de suporte técnico
da HP para que um técnico o ajude por telefone. A HP especifica nos materiais fornecidos com a peça CSR
de reposição se a peça com defeito deve ser devolvida à HP. Nos casos em que isso for necessário, é
preciso enviar a peça com defeito à HP dentro do período determinado, normalmente cinco (5) dias úteis.
A peça com defeito deve ser enviada com a documentação correspondente no material de transporte
fornecido. Caso não o faça, a HP poderá cobrar a reposição. Para as peças de reparo feito pelo cliente, a
HP paga todas as despesas de transporte e de devolução da peça e determina a transportadora/serviço
postal a ser utilizado.
Para obter mais informações sobre o programa de reparo feito pelo cliente da HP, entre em contato com o
fornecedor de serviços local. Para o programa norte-americano, visite o site da HP
(http://www.hp.com/go/selfrepair).
Serviço de garantia apenas para peças
A garantia limitada da HP pode incluir um serviço de garantia apenas para peças. Segundo os termos do
serviço de garantia apenas para peças, a HP fornece as peças de reposição sem cobrar nenhuma taxa.
Customer self repair 10
No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP substitua essas
peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
Customer self repair 11
Customer self repair 12
Customer self repair 13
Customer self repair 14
Illustrated parts catalog
Mechanical components
Item
Description
Spare part number
Customer self repair
(on page 5)
1
Access panel
696239-001
Mandatory1
2
Air baffle
696238-001
Mandatory1
3
Front cage assembly
696240-001
Optional2
4
PCIe riser cage
662526-001
Optional2
5
Hard drive blank
667276-001
Optional2
6
Hardware blank kit
662519-001
Mandatory1
a) FlexibleLOM blank*
—
—
b) PCIe riser cage blank*
—
—
c) Expansion slot blank*
—
—
d) Power supply blank
—
—
e) Optical device blank*
—
—
f) Fan blank*
—
—
Illustrated parts catalog
15
Item
Description
Spare part number
Customer self repair
(on page 5)
7
Rack mounting hardware
—
—
a) Ball bearing rail kit, LFF
692480-001
Mandatory1
b) Cable management arm*
675606-001
Mandatory1
8
Heatsink blank
662522-001
Mandatory1
9
Plastics kit
696243-001
Mandatory1
a) Capacitor pack cable routing guide*
—
—
b) Capacitor pack holder
—
—
c) Capacitor pack cable routing trough*
—
—
10
Processor cage*
662537-001
Optional2
11
2U rack bezel*
662529-001
Mandatory1
* Not shown
1
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be
charged for the travel and labor costs of this service.
2
Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If,
however, you require that HP replace them for you, there may or may not be additional charges, depending on the type
of warranty service designated for your product.
3
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty, HP requires that
an authorized service provider replace the part. These parts are identified as "No" in the Illustrated Parts Catalog.
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de
remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
2
Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également
conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous demandez à HP de remplacer ces
pièces, l'intervention peut ou non vous être facturée, selon le type de garantie applicable à votre produit.
3
No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la réparation. Pour
que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit effectué par un Mainteneur Agréé. Ces
pièces sont identifiées par la mention “Non” dans le Catalogue illustré.
1
Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida la
riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio.
2
Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di componenti
progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP, potrebbe dover sostenere spese
addizionali a seconda del tipo di garanzia previsto per il prodotto.
3
No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare la
garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti sono identificate
da un “No” nel Catalogo illustrato dei componenti.
1
Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden müssen. Wenn Sie
diese Teile von HP ersetzen lassen, werden Ihnen die Versand- und Arbeitskosten für diesen Service berechnet.
2
Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für Customer
Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen lassen möchten, können bei
diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche Kosten anfallen.
3
No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen,
muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw.
„Nein“ gekennzeichnet.
1
Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es obligatoria. Si solicita a HP
que realice la sustitución de estos componentes, tendrá que hacerse cargo de los gastos de desplazamiento y de mano
de obra de dicho servicio.
1
Illustrated parts catalog
16
Optional: Opcional— componentes para los que la reparación por parte del usuario es opcional. Estos componentes
también están diseñados para que puedan ser reparados por el usuario. Sin embargo, si precisa que HP realice su
sustitución, puede o no conllevar costes adicionales, dependiendo del tipo de servicio de garantía correspondiente al
producto.
3
No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para que el usuario
haga valer su garantía, HP pone como condición que un proveedor de servicios autorizado realice la sustitución de estos
componentes. Dichos componentes se identifican con la palabra “No” en el catálogo ilustrado de componentes.
2
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt deze onderdelen te
vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
2
Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn
ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen, kunnen
daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor het product.
3
No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband met de
garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden vervangen. Deze
onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee".
1
Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas peças,
serão cobradas as despesas de transporte e mão-de-obra do serviço.
2
Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o
reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa
adicional, dependendo do tipo de serviço de garantia destinado ao produto.
3
No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de cumprir a garantia
do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças estão identificadas com a marca “No”
(Não), no catálogo de peças ilustrado.
1
Illustrated parts catalog
17
System components
Item
Description
Spare part number
Customer self repair (on
page 5)
System components
12
Hot-plug fan module
696241-001
Mandatory1
13
Power supply, hot-plug 1200 W, Platinum Plus,
94%
Processors
660185-001
Mandatory1
—
—
14
a) 2.4-GHz Intel Xeon processor E5-4657L v2
733831-001
115W
b) 2.7-GHz Intel Xeon processor E5-4650 130W* 687963-001
Optional2
c) 2.4-GHz Intel Xeon processor E5-4650 v2
95W*
d) 2.4-GHz Intel Xeon processor E5-4640 95W*
733832-001
Optional2
687964-001
Optional2
e) 2.2-GHz Intel Xeon processor E5-4640 v2
95W*
f) 2.2-GHz Intel Xeon processor E5-4620 95W*
733833-001
Optional2
687965-001
Optional2
g) 2.6-GHz Intel Xeon processor E5-4620 v2
95W*
h) 2.4-GHz Intel Xeon processor E5-4610 95W*
733834-001
Optional2
687966-001
Optional2
i) 2.3-GHz Intel Xeon processor E5-4610 v2 95W* 733835-001
Optional2
j) 2.2-GHz Intel Xeon processor E5-4607 95W*
687967-001
Optional2
k) 2.6-GHz Intel Xeon processor E5-4607 v2
95W*
l) 2.0-GHz Intel Xeon processor E5-4603 95W*
733836-001
Optional2
687968-001
Optional2
m) 2.2 GHz Intel Xeon processor E5-4603 v2
733837-001
95W*
n) 2.6-GHz Intel Xeon processor E5-4650 115W* 687969-001
Optional2
Optional2
Optional2
Illustrated parts catalog
18
Item
15
Description
Spare part number
Customer self repair (on
page 5)
o) 3.3-GHz Intel Xeon processor E5-4627 v2*
733838-001
Optional2
p) 2.9-GHz Intel Xeon processor E5-4617 130W* 687970-001
Optional2
Heatsink, standard efficiency
662522-001
Optional2
Hot-plug SAS drives
—
—
a) 300-GB, 10,000-rpm, SFF, 6G, dual port
653955-001
Mandatory1
b) 450-GB, 10,000-rpm, SFF, 6G, dual port*
653956-001
Mandatory1
c) 600-GB, 10,000-rpm, SFF, 6G, dual port*
653957-001
Mandatory1
d) 900-GB, 10,000-rpm, SFF, 6G, dual port*
653971-001
Mandatory1
e) 146-GB, 15,000-rpm, SFF, 6G, dual port*
653950-001
Mandatory1
f) 300-GB, 15,000-rpm, SFF, 6G, dual port*
653960-001
Mandatory1
g) 500-GB, 7,200-rpm, SFF, 6G, dual port*
653953-001
Mandatory1
h) 1-TB, 7,200-rpm, SFF, 6G, dual port*
653954-001
Mandatory1
Hot-plug solid state SAS drives*
—
—
a) 200-GB, SFF, SLC SC
653961-001
Mandatory1
b) 400-GB, SFF, SLC SC
653962-001
Mandatory1
c) 400-GB, SFF, MLC SC
653963-001
Mandatory1
d) 800-GB, SFF, MLC SC
653964-001
Mandatory1
e) 200-GB, SFF, MLC SC
658580-001
Mandatory1
Hot-plug solid state SATA drives*
—
—
a) 100-GB, SFF, MLC SC, 3G
653965-001
Mandatory1
b) 200-GB, SFF, MLC SC, 3G
653966-001
Mandatory1
c) 400-GB, SFF, MLC SC, 3G
653967-001
Mandatory1
DIMMs
—
—
a) 4-GB, PC3-14900R-13, single-rank x4*
715272-001
Mandatory1
b) 4-GB, PC3L-12800R-11, single-rank x4*
715282-001
Mandatory1
c) 4-GB, PC3-12800R-11, single-rank x4*
664689-001
Mandatory1
d) 4-GB, PC3L-10600R-9, single-rank x4*
664688-001
Mandatory1
e) 8-GB, PC3-14900R-13, single-rank x4*
735303-001
Mandatory1
f) 8-GB, PC3-14900R-13, dual-rank x4*
715273-001
Mandatory1
g) 8-GB, PC3L-12800R-11, dual-rank x4*
715283-001
Mandatory1
h) 8-GB, PC3-12800R-11, single-rank x4*
664691-001
Mandatory1
i) 8 GB, PC3-12800R-11, dual-rank x4*
698807-001
Mandatory1
j) 8-GB, PC3L-10600R-9, dual-rank x4*
664690-001
Mandatory1
Drives
16
17
18
Memory
19
Illustrated parts catalog
19
Item
Description
Spare part number
Customer self repair (on
page 5)
k) 16-GB, PC3-14900R-13, dual-rank x4*
715274-001
Mandatory1
l) 16-GB, PC3L-12800R-11, dual-rank x4*
715284-001
Mandatory1
m) 16-GB, PC3-12800R-11, dual-rank x4*
684031-001
Mandatory1
n) 16-GB, PC3L-10600R-9, dual-rank x4*
664692-001
Mandatory1
o) 32-GB, PC3-14900L-13, quad-rank x4*
715275-001
Mandatory1
p) 32-GB, PC3L-10600L-9, quad-rank x4*
664693-001
Mandatory1
PCIe riser board
—
—
a) PCIe riser board, standard 3-slot
662524-001
Optional2
b) PCIe riser board, optional 2-slot*
662525-001
Optional2
21
Power supply backplane
662528-001
Mandatory1
22
FlexibleLOM
—
—
a) HP 1GbE 4-port, 331FLR Adapter FIO Kit
634025-001
Mandatory1
b) HP 10GbE 2-port, 530FLR Adapter FIO Kit*
649869-001
Mandatory1
634026-001
Mandatory1
656090-001
Mandatory1
656091-001
Mandatory1
23
c) HP Ff 10Gb 2-port, 554FLR-SFP+ Adapter FIO
Kit*
d) HP InfiniBand FDR/EN 10/40Gb 2-port,
544FLR-QSFP Adapter*
e) HP InfiniBand QDR/EN 10Gb 2-port,
544FLR-QSFP Adapter*
System board assembly
696237-001
Optional2
24
HP Trusted Platform Module
505836-001
No3
Controller option
—
—
FBWC cache module
—
—
a) 512-MB cache
633540-001
Optional2
b) 1-GB cache*
633542-001
Optional2
c) 2-GB cache*
633543-001
Optional2
FBWC capacitor pack
—
—
a) 24-inch FBWC capacitor pack with cable
660092-001
Optional2
b) 36-inch FBWC capacitor pack with cable*
660093-001
Optional2
Systems Insight Display subassembly, with cables* 664927-001
Optional2
Boards
20
25
26
Systems Insight Display
27
Cables
28
Cable kit*
696242-001*
Mandatory1
a) Mini-SAS hard drive backplane to storage card —
—
b) Primary power cable 2x4
—
—
c) Secondary power cable 2x4
—
—
d) Sideband fan cable
—
—
Illustrated parts catalog
20
Item
Description
Spare part number
Customer self repair (on
page 5)
29
Mini-SAS storage cable*
699144-001
Mandatory1
Battery
—
—
System battery, 3.3-V, lithium*
153099-001
Mandatory1
30
*Not shown
**All processors in this HP ProLiant server must have the same cache size, speed, number of cores, and rated maximum
power consumption.
1
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be
charged for the travel and labor costs of this service.
2
Optional—Parts for which customer self repair is optional. These parts are also designed for customer self repair. If,
however, you require that HP replace them for you, there may or may not be additional charges, depending on the type
of warranty service designated for your product.
3
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer warranty, HP requires that
an authorized service provider replace the part. These parts are identified as "No" in the Illustrated Parts Catalog.
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de
remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés.
2
Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également
conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous demandez à HP de remplacer ces
pièces, l'intervention peut ou non vous être facturée, selon le type de garantie applicable à votre produit.
3
No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la réparation. Pour
que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit effectué par un Mainteneur Agréé. Ces
pièces sont identifiées par la mention “Non” dans le Catalogue illustré.
1
Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida la
riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio.
2
Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di componenti
progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP, potrebbe dover sostenere spese
addizionali a seconda del tipo di garanzia previsto per il prodotto.
3
No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per rispettare la
garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza autorizzato. Tali parti sono identificate
da un “No” nel Catalogo illustrato dei componenti.
1
Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden müssen. Wenn Sie
diese Teile von HP ersetzen lassen, werden Ihnen die Versand- und Arbeitskosten für diesen Service berechnet.
2
Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch für Customer
Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP vornehmen lassen möchten, können bei
diesem Service je nach den für Ihr Produkt vorgesehenen Garantiebedingungen zusätzliche Kosten anfallen.
3
No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen,
muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw.
„Nein“ gekennzeichnet.
1
Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es obligatoria. Si solicita a HP
que realice la sustitución de estos componentes, tendrá que hacerse cargo de los gastos de desplazamiento y de mano
de obra de dicho servicio.
2
Optional: Opcional— componentes para los que la reparación por parte del usuario es opcional. Estos componentes
también están diseñados para que puedan ser reparados por el usuario. Sin embargo, si precisa que HP realice su
sustitución, puede o no conllevar costes adicionales, dependiendo del tipo de servicio de garantía correspondiente al
producto.
3
No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario. Para que el usuario
haga valer su garantía, HP pone como condición que un proveedor de servicios autorizado realice la sustitución de estos
componentes. Dichos componentes se identifican con la palabra “No” en el catálogo ilustrado de componentes.
1
Illustrated parts catalog
21
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt deze onderdelen te
vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
2
Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn
ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te vervangen, kunnen
daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type garantieservice voor het product.
3
No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband met de
garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden vervangen. Deze
onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met "Nee".
1
Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas peças,
serão cobradas as despesas de transporte e mão-de-obra do serviço.
2
Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o
reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa
adicional, dependendo do tipo de serviço de garantia destinado ao produto.
3
No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de cumprir a garantia
do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças estão identificadas com a marca “No”
(Não), no catálogo de peças ilustrado.
1
Illustrated parts catalog
22
Removal and replacement procedures
Required tools
You need the following items for some procedures:
•
T-10/T-15 Torx screwdriver
•
HP Insight Diagnostics software ("HP Insight Diagnostics" on page 66)
Safety considerations
Before performing service procedures, review all the safety information.
Preventing electrostatic discharge
To prevent damaging the system, be aware of the precautions you need to follow when setting up the system
or handling parts. A discharge of static electricity from a finger or other conductor may damage system
boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
To prevent electrostatic damage:
•
Avoid hand contact by transporting and storing products in static-safe containers.
•
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
•
Place parts on a grounded surface before removing them from their containers.
•
Avoid touching pins, leads, or circuitry.
•
Always be properly grounded when touching a static-sensitive component or assembly.
Symbols on equipment
The following symbols may be placed on equipment to indicate the presence of potentially hazardous
conditions.
This symbol indicates the presence of hazardous energy circuits or electric shock
hazards. Refer all servicing to qualified personnel.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure. Refer all maintenance, upgrades, and servicing to qualified personnel.
This symbol indicates the presence of electric shock hazards. The area contains no user
or field serviceable parts. Do not open for any reason.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure.
Removal and replacement procedures
23
This symbol on an RJ-45 receptacle indicates a network interface connection.
WARNING: To reduce the risk of electric shock, fire, or damage to the equipment, do
not plug telephone or telecommunications connectors into this receptacle.
This symbol indicates the presence of a hot surface or hot component. If this surface is
contacted, the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow the surface to cool
before touching.
27.66
61.00
This symbol indicates that the component exceeds the recommended weight for one
individual to handle safely.
WARNING: To reduce the risk of personal injury or damage to the equipment, observe
local occupational health and safety requirements and guidelines for manual material
handling.
These symbols, on power supplies or systems, indicate that the equipment is supplied
by multiple sources of power.
WARNING: To reduce the risk of injury from electric shock, remove all power cords to
completely disconnect power from the system.
Server warnings and cautions
Before installing a server, be sure that you understand the following warnings and cautions.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it.
Pay particular attention to the plug, electrical outlet, and the point where the cord extends from
the server.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
CAUTION: Do not operate the server for long periods with the access panel open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can
lead to thermal damage.
Preparation procedures
To access some components and perform certain service procedures, you must perform one or more of the
following procedures:
•
Extend the server from the rack (on page 25).
Removal and replacement procedures
24
If you are performing service procedures in an HP, Compaq branded, telco, or third-party rack cabinet,
you can use the locking feature of the rack rails to support the server and gain access to internal
components.
For more information about telco rack solutions, refer to the RackSolutions.com website
(http://www.racksolutions.com/hp).
•
Power down the server (on page 25).
If you must remove a server from a rack or a non-hot-plug component from a server, power down the
server.
•
Remove the server from the rack (on page 26).
If the rack environment, cabling configuration, or the server location in the rack creates awkward
conditions, remove the server from the rack.
•
Access the product rear panel (on page 27).
•
Access the Systems Insight Display (on page 27).
•
Release the full-length expansion board retainer (on page 28).
Power down the server
Before powering down the server for any upgrade or maintenance procedures, perform a backup of critical
server data and programs.
IMPORTANT: When the server is in standby mode, auxiliary power is still being provided to the
system.
To power down the server, use one of the following methods:
•
Press and release the Power On/Standby button.
This method initiates a controlled shutdown of applications and the OS before the server enters standby
mode.
•
Press and hold the Power On/Standby button for more than 4 seconds to force the server to enter
standby mode.
This method forces the server to enter standby mode without properly exiting applications and the OS.
If an application stops responding, you can use this method to force a shutdown.
•
Use a virtual power button selection through HP iLO.
This method initiates a controlled remote shutdown of applications and the OS before the server enters
standby mode.
Before proceeding, verify the server is in standby mode by observing that the system power LED is amber.
Extend the server from the rack
WARNING: To reduce the risk of personal injury or equipment damage, be sure that the rack is
adequately stabilized before extending a component from the rack.
1.
Pull down the quick release levers on each side of the server.
Removal and replacement procedures
25
2.
Extend the server from the rack.
3.
After performing the installation or maintenance procedure, slide the server back into the rack, and then
press the server firmly into the rack to secure it in place.
WARNING: To reduce the risk of personal injury, be careful when pressing the server rail-release
latches and sliding the server into the rack. The sliding rails could pinch your fingers.
Remove the server from the rack
To remove the server from an HP, Compaq branded, telco, or third-party rack:
1.
Power down the server (on page 25).
2.
Extend the server from the rack (on page 25).
3.
Disconnect the cabling and remove the server from the rack. For more information, refer to the
documentation that ships with the rack mounting option.
4.
Place the server on a sturdy, level surface.
Removal and replacement procedures
26
Access the Systems Insight Display
To access the HP Systems Insight Display:
1.
Press and release the panel.
2.
After the display fully ejects, rotate the display sideways to view the LEDs.
Access the product rear panel
Opening the cable management arm
To access the server rear panel:
1.
Release the cable management arm.
Removal and replacement procedures
27
2.
Open the cable management arm. The cable management arm can be right-mounted or left-mounted.
Release the full-length expansion board retainer
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
Release the full-length expansion board retainer.
To replace the component, reverse the removal procedure.
Removal and replacement procedures
28
Access panel
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
CAUTION: For proper cooling, do not operate the server without the access panel, baffles,
expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize
the amount of time the access panel is open.
To remove the component:
1.
Power down the server if performing a non-hot-plug installation or maintenance procedure ("Power
down the server" on page 25).
2.
Extend the server from the rack (on page 25).
3.
Use a T-15 Torx screwdriver to loosen the security screw on the hood latch.
4.
Lift up on the hood latch handle, and then remove the access panel.
To replace the component, reverse the removal procedure.
Air baffle
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
CAUTION: For proper cooling, do not operate the server without the access panel, baffles,
expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize
the amount of time the access panel is open.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
CAUTION: Do not detach the cable that connects the battery pack to the cache module.
Detaching the cable causes any unsaved data in the cache module to be lost.
IMPORTANT: It is necessary to remove the PCI riser cage only if there is a full-length expansion
board installed.
Removal and replacement procedures
29
5.
6.
If any full-length expansion boards are installed, do one of the following:
o
Remove the primary PCIe riser cage ("PCIe riser cage (primary)" on page 31)
o
Remove the secondary PCIe riser cage ("PCIe riser cage (secondary)" on page 32)
Remove the air baffle.
To replace the component, reverse the removal procedure.
2U rack bezel
To remove the component:
Unlock the 2U rack bezel, press the latch on the 2U rack bezel, and then remove the 2U rack bezel.
To replace the component, reverse the removal procedure.
Removal and replacement procedures
30
PCIe riser blank
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all PCI slots have either an expansion slot cover or an expansion board installed.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
Remove the PCIe riser blank.
To replace the component, reverse the removal procedure.
PCIe riser cage (primary)
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
Removal and replacement procedures
31
4.
Remove the access panel ("Access panel" on page 29).
5.
Disconnect any external cables that are connected to the expansion board.
6.
Disconnect any internal cables that are connected to the expansion board.
7.
If any full-length expansion boards are installed, release the full-length expansion board retainer (on
page 28).
8.
Remove the PCIe riser cage.
To replace the component, reverse the removal procedure.
PCIe riser cage (secondary)
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
Disconnect any external cables that are connected to the expansion board.
6.
Disconnect any internal cables that are connected to the expansion board.
7.
If any full-length expansion boards are installed, release the full-length expansion board retainer (on
page 28).
Removal and replacement procedures
32
8.
Remove the secondary PCIe riser cage.
To replace the component, reverse the removal procedure.
PCIe riser board
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
If any full-length expansion boards are installed, release the full-length expansion board retainer (on
page 28).
6.
Remove the PCIe riser cage ("PCIe riser cage (primary)" on page 31).
7.
Remove any expansion boards from the PCIe riser cage ("Expansion boards" on page 47).
Removal and replacement procedures
33
8.
Remove the PCIe riser board.
To replace the component, reverse the removal procedure.
Drive blank
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
Remove the drive blank.
To replace the component, slide the component into the bay until it clicks.
Hot-plug drive
CAUTION: For proper cooling, do not operate the server without the access panel, baffles,
expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize
the amount of time the access panel is open.
1.
Determine the status of the drive from the hot-plug drive LED definitions (on page 77).
2.
Back up all server data on the drive.
Removal and replacement procedures
34
3.
Remove the drive.
To replace the component, reverse the removal procedure.
Power supply blank
Remove the blank.
To replace the component, reverse the removal procedure.
AC power supply
CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless
all bays are populated with either a component or a blank.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Access the product rear panel (on page 27).
4.
Remove the power supply.
Removal and replacement procedures
35
WARNING: To reduce the risk of personal injury from hot surfaces, allow the power supply or
power supply blank to cool before touching it.
To replace the component, reverse the removal procedure.
Power supply backplane
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Remove all power supplies ("AC power supply" on page 35).
4.
Extend the server from the rack (on page 25).
5.
Remove the access panel ("Access panel" on page 29).
Removal and replacement procedures
36
6.
Disconnect the USB cable.
7.
Remove the power supply backplane.
To replace the component, reverse the removal procedure.
Hot-plug fan
CAUTION: To avoid damage to server components, all fan modules must be installed in fan bays
for any processor configuration.
For all processor configurations, the HP ProLiant DL560 Gen8 Server requires six fan modules for
redundancy. A fan failure causes a loss of cooling redundancy. A second fan failure or a missing fan module
causes an orderly shutdown of the server.
The server supports variable fan speeds. The fans operate at minimum speed until a temperature change
requires a fan speed increase to cool the server.
Removal and replacement procedures
37
The server shuts down in the following temperature-related scenarios:
•
At POST and in the OS, HP iLO performs an orderly shutdown if a cautionary temperature level is
detected. If the server hardware detects a critical temperature level before an orderly shutdown occurs,
the server performs an immediate shutdown.
•
When the Thermal Shutdown feature is disabled in RBSU, HP iLO does not perform an orderly shutdown
when a cautionary temperature level is detected. Disabling this feature does not disable the server
hardware from performing an immediate shutdown when a critical temperature level is detected.
CAUTION: A thermal event can damage server components when the Thermal Shutdown feature
is disabled in RBSU.
IMPORTANT: An immediate shutdown is a hardware-controlled function and it overrides any
firmware or software actions.
To remove the component:
1.
Remove the fan module.
CAUTION: Do not operate the server for long periods with the access panel open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can
lead to thermal damage.
To replace the component, reverse the removal procedure.
FlexibleLOM
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
To remove the component:
1.
Power down the server (on page 25).
Removal and replacement procedures
38
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Remove any attached network cables.
4.
Extend the server from the rack (on page 25).
5.
Remove the access panel ("Access panel" on page 29).
6.
Remove the primary PCIe riser cage ("PCIe riser cage (primary)" on page 31).
7.
Loosen the thumbscrew.
8.
Remove the existing FlexibleLOM.
Using the blue touchpoint tabs, pull the FlexibleLOM toward the front of the server while removing it, to
avoid catching it on the rear chassis.
To replace the component:
1.
Using the blue touchpoint tabs, firmly seat the FlexibleLOM in the slot, and then tighten the thumbscrew.
Removal and replacement procedures
39
2.
Install the PCIe riser cage ("PCIe riser cage (primary)" on page 31).
3.
Install the access panel ("Access panel" on page 29).
4.
Slide the server into the rack.
5.
Connect the LAN segment cables.
6.
Connect each power cord to the server.
7.
Connect each power cord to the power source.
8.
Power up the server.
Front panel assembly
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
Remove the serial label pull tab and retain it for the new front panel assembly.
6.
Remove the air baffle ("Air baffle" on page 29).
7.
Remove all fan modules ("Hot-plug fan" on page 37).
8.
Remove all drives ("Hot-plug drive" on page 34).
9.
Disconnect all cables from the front panel assembly.
Removal and replacement procedures
40
IMPORTANT: If any cables in the front panel assembly need replacing, the entire front panel
assembly must be replaced.
10.
Remove the four T-10 Torx screws from each side, and then remove the front panel assembly.
To replace the component, reverse the removal procedure.
Flash-backed write cache procedures
Two types of procedures are provided for the FBWC option:
•
•
Removal and replacement of failed components:
o
Removing the cache module ("Flash-backed write cache module" on page 41)
o
Removing the capacitor pack ("Flash-backed write cache capacitor pack" on page 43)
Recovery of cached data from a failed server ("Recovering data from the flash-backed write cache" on
page 45)
CAUTION: Do not detach the cable that connects the battery pack or capacitor pack to the cache
module. Detaching the cable causes all data in the cache module to be lost.
Flash-backed write cache module
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
To remove the component:
CAUTION: The cache module connector does not use the industry-standard DDR3 mini-DIMMs.
Do not use the controller with cache modules designed for other controller models, because the
controller can malfunction and you can lose data. Also, do not transfer this cache module to an
unsupported controller model, because you can lose data.
Removal and replacement procedures
41
1.
Back up all data.
2.
Close all applications.
3.
Power down the server (on page 25).
4.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
CAUTION: In systems that use external data storage, be sure that the server is the first unit to be
powered down and the last to be powered back up. Taking this precaution ensures that the system
does not erroneously mark the drives as failed when the server is powered up.
5.
Extend the server from the rack (on page 25).
6.
Remove the access panel ("Access panel" on page 29).
7.
If it is populated with expansion boards, remove the PCIe riser cage for better access ("PCIe riser cage
(primary)" on page 31).
8.
If the existing cache module is connected to a capacitor pack, observe the FBWC module LEDs:
9.
o
If the amber LED is flashing, data is trapped in the cache. Restore system power, and then restart this
procedure from step 1.
o
If the amber LED is not illuminated, remove the controller from the server, and then continue with the
next step.
Open the ejector latches on each side of the cache module connector. Normally, the cache module is
ejected from the cache module connector. If the module is not ejected automatically, remove the cache
module.
Removal and replacement procedures
42
10.
If the cache module is connected to a capacitor pack, disconnect the capacitor pack cable from the
connector on the top of the cache module.
To replace the component, reverse the removal procedure.
CAUTION: To prevent damage to the cache module during installation, be sure the cache
module is fully inserted before pressing down.
Flash-backed write cache capacitor pack
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
To remove the component:
1.
Back up all data.
2.
Close all applications.
3.
Power down the server (on page 25).
4.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
CAUTION: In systems that use external data storage, be sure that the server is the first unit to be
powered down and the last to be powered back up. Taking this precaution ensures that the system
does not erroneously mark the drives as failed when the server is powered up.
5.
Extend the server from the rack (on page 25).
6.
Remove the access panel ("Access panel" on page 29).
7.
If it is populated with expansion boards, remove the PCIe riser cage for better access ("PCIe riser cage
(primary)" on page 31).
Removal and replacement procedures
43
8.
If the capacitor pack is connected to the cache module, disconnect the capacitor pack cable from the
connector on the top of the cache module.
9.
Disconnect the SAS hard drive backplane ribbon cable.
10.
Remove the capacitor pack.
o
Single capacitor pack holder:
Removal and replacement procedures
44
o
Double capacitor pack holder:
To replace the component, reverse the removal procedure.
Recovering data from the flash-backed write cache
If the server fails, use the following procedure to recover data temporarily stored in the FBWC.
CAUTION: Before starting this procedure, read the information about protecting against
electrostatic discharge ("Preventing electrostatic discharge" on page 23).
1.
Perform one of the following:
o
Set up a recovery server using an identical server model. Do not install any internal drives or FBWC
in this server. (HP recommends this option.)
o
Find a server that has enough empty drive bays to accommodate all the drives from the failed server
and that meets all the other requirements for drive and array migration.
2.
Power down the failed server ("Power down the server" on page 25).
3.
Transfer the drives from the failed server to the recovery server.
4.
Perform one of the following:
5.
o
If the array controller has failed, remove the cache module ("Flash-backed write cache module" on
page 41) and capacitor pack ("Flash-backed write cache capacitor pack" on page 43) from the
failed array controller, and install the cache module and capacitor pack on an identical array
controller model in the recovery server.
o
If the server has failed, remove the controller ("Half-length expansion board" on page 47), cache
module ("Flash-backed write cache module" on page 41), and capacitor pack ("Flash-backed write
cache capacitor pack" on page 43) from the failed server, and install the controller, cache module,
and capacitor pack in the recovery server.
Power up the recovery server. If there was data in the cache at the time of the controller or server failure,
a 1792 POST message appears, stating that valid data was flushed from the cache. This data is now
stored on the drives in the recovery server. You can now transfer the drives (and controller, if one is
used) to another server.
Removal and replacement procedures
45
If the drives are migrated to different drive positions or there are volumes present in the recovery server,
a 1724 POST message appears, stating that logical drive configuration has been updated
automatically.
Expansion slot blanks
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
CAUTION: For proper cooling, do not operate the server without the access panel, baffles,
expansion slot covers, or blanks installed. If the server supports hot-plug components, minimize
the amount of time the access panel is open.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
Disconnect any external cables that are connected to the expansion board.
6.
Disconnect any internal cables that are connected to the expansion board.
7.
Remove the PCIe riser cage ("PCIe riser cage (primary)" on page 31).
8.
Remove the expansion slot blank.
To replace the component, reverse the removal procedure.
Removal and replacement procedures
46
Expansion boards
Half-length expansion board
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
Disconnect any external cables that are connected to the expansion board.
6.
Disconnect any internal cables that are connected to the expansion board.
7.
Remove the PCIe riser cage ("PCIe riser cage (primary)" on page 31).
8.
Remove the expansion board.
To replace the component, reverse the removal procedure.
Full length expansion board
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
Removal and replacement procedures
47
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
Disconnect any external cables that are connected to the expansion board.
6.
Disconnect any internal cables that are connected to the expansion board.
7.
Release the full-length expansion board retainer, and then remove the PCIe riser cage.
8.
Remove the full-length expansion board.
To replace the component, reverse the removal procedure.
Heatsink
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
CAUTION: The heatsink thermal interface media is not reusable and must be replaced if the
heatsink is removed from the processor after it has been installed.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
Removal and replacement procedures
48
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
Remove the air baffle ("Air baffle" on page 29).
6.
Remove the heatsink.
Removal and replacement procedures
49
To replace the component:
1.
Remove the thermal interface protective cover from the heatsink.
2.
Install the heatsink.
3.
Install the air baffle ("Air baffle" on page 29).
4.
Install the access panel ("Access panel" on page 29).
5.
Slide the server into the rack.
6.
Connect each power cord to the server.
7.
Connect each power cord to the power source.
Removal and replacement procedures
50
8.
Power up the server.
Processor
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the
internal system components to cool before touching them.
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
CAUTION: To prevent possible server malfunction and damage to the equipment, multiprocessor
configurations must contain processors with the same part number.
CAUTION: The heatsink thermal interface media is not reusable and must be replaced if the
heatsink is removed from the processor after it has been installed.
CAUTION: To prevent possible server overheating, always populate processor socket 2 with a
processor and a heatsink or a processor socket cover and a heatsink blank.
IMPORTANT: Processor socket 1 must be populated at all times or the server does not function.
To remove the processor:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
Remove the air baffle ("Air baffle" on page 29).
6.
Remove the heatsink ("Heatsink" on page 48).
Removal and replacement procedures
51
7.
Open each of the processor locking levers in the order indicated, and then open the processor retaining
bracket.
8.
Remove the processor from the processor retaining bracket.
CAUTION: To avoid damage to the processor, do not touch the bottom of the processor,
especially the contact area.
Removal and replacement procedures
52
To replace the component:
1.
Install the processor. Verify that the processor is fully seated in the processor retaining bracket by
visually inspecting the processor installation guides on either side of the processor. THE PINS ON THE
SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED.
CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. To
avoid damage to the system board, do not touch the processor or the processor socket contacts.
2.
Close the processor retaining bracket. When the processor is installed properly inside the processor
retaining bracket, the processor retaining bracket clears the flange on the front of the socket.
CAUTION: Do not press down on the processor. Pressing down on the processor may cause
damage to the processor socket and the system board. Press only in the area indicated on the
processor retaining bracket.
Removal and replacement procedures
53
3.
Press and hold the processor retaining bracket in place, and then close each processor locking lever.
Press only in the area indicated on the processor retaining bracket.
4.
Clean the old thermal grease from the heatsink with the alcohol swab. Allow the alcohol to evaporate
before continuing.
5.
Apply all the grease to the top of the processor in the following pattern to ensure even distribution.
Removal and replacement procedures
54
6.
Install the heatsink.
7.
Install the air baffle ("Air baffle" on page 29).
8.
Install the access panel ("Access panel" on page 29).
9.
Slide the server into the rack.
10.
Connect each power cord to the server.
11.
Connect each power cord to the power source.
12.
Power up the server.
DIMMs
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
IMPORTANT: This server does not support mixing RDIMMs and UDIMMs. Attempting to mix
these two types causes the server to halt during BIOS initialization.
To identify the DIMMs installed in the server, see "DIMM slot locations (on page 77)."
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
Removal and replacement procedures
55
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
Remove the air baffle ("Air baffle" on page 29).
6.
Remove the DIMM.
To replace the component, reverse the removal procedure.
For DIMM configuration information, see the server user guide.
System battery
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
If the server no longer automatically displays the correct date and time, you may need to replace the battery
that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years.
WARNING: The computer contains an internal lithium manganese dioxide, a vanadium
pentoxide, or an alkaline battery pack. A risk of fire and burns exists if the battery pack is not
properly handled. To reduce the risk of personal injury:
•
•
•
•
Do not attempt to recharge the battery.
Do not expose the battery to temperatures higher than 60°C (140°F).
Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
Replace only with the spare designated for this product.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
Removal and replacement procedures
56
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove the access panel ("Access panel" on page 29).
5.
Remove the secondary PCIe riser cage ("PCIe riser cage (secondary)" on page 32), if installed.
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the expansion boards.
6.
Remove the battery.
IMPORTANT: Replacing the system board battery resets the system ROM to its default
configuration. After replacing the battery, reconfigure the system through RBSU.
To replace the component, reverse the removal procedure.
For more information about battery replacement or proper disposal, contact an authorized reseller or an
authorized service provider.
System board
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
To remove the component:
1.
Power down the server (on page 25).
2.
Remove all power:
a. Disconnect each power cord from the power source.
b. Disconnect each power cord from the server.
3.
Extend the server from the rack (on page 25).
4.
Remove all power supplies ("AC power supply" on page 35).
Removal and replacement procedures
57
5.
Remove the access panel ("Access panel" on page 29).
6.
Remove the air baffle ("Air baffle" on page 29).
7.
Remove the PCIe riser cage ("PCIe riser cage (primary)" on page 31).
8.
If installed, remove the secondary PCIe riser cage ("PCIe riser cage (secondary)" on page 32).
9.
If installed, remove the FBWC capacitor pack ("Flash-backed write cache capacitor pack" on page
43).
10.
If installed, remove the cache module ("Flash-backed write cache module" on page 41).
11.
Remove the FlexibleLOM ("FlexibleLOM" on page 38).
12.
Remove all DIMMs ("DIMMs" on page 55).
13.
Remove the power supply backplane ("Power supply backplane" on page 36).
14.
Disconnect all cables connected to the system board.
15.
Remove the heatsink ("Heatsink" on page 48).
16.
Remove the processor ("Processor" on page 51).
17.
Loosen the system board thumbscrews.
18.
Remove the system board, using the handle to lift it out of the chassis.
Removal and replacement procedures
58
To replace the component:
1.
Install the spare system board.
2.
Open each of the processor locking levers in the order indicated, and then open the processor retaining
bracket.
Removal and replacement procedures
59
3.
Remove the clear processor socket cover. Retain the processor socket cover for future use.
4.
Install the processor. Verify that the processor is fully seated in the processor retaining bracket by
visually inspecting the processor installation guides on either side of the processor. THE PINS ON THE
SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED.
CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. To
avoid damage to the system board, do not touch the processor or the processor socket contacts.
5.
Close the processor retaining bracket. When the processor is installed properly inside the processor
retaining bracket, the processor retaining bracket clears the flange on the front of the socket.
Removal and replacement procedures
60
CAUTION: Do not press down on the processor. Pressing down on the processor may cause
damage to the processor socket and the system board. Press only in the area indicated on the
processor retaining bracket.
6.
Press and hold the processor retaining bracket in place, and then close each processor locking lever.
Press only in the area indicated on the processor retaining bracket.
7.
Install the processor socket cover onto the processor socket of the failed system board.
8.
Clean the old thermal grease from the heatsink and the top of the processor with the alcohol swab.
Allow the alcohol to evaporate before continuing.
9.
Apply all the grease to the top of the processor in the following pattern to ensure even distribution.
Removal and replacement procedures
61
10.
Install the heatsink.
IMPORTANT: Install all components with the same configuration that was used on the failed
system board.
11.
Install all components removed from the failed system board.
12.
Install the access panel ("Access panel" on page 29).
13.
Install the power supplies ("AC power supply" on page 35).
14.
Power up the server.
After you replace the system board, you must re-enter the server serial number and the product ID.
1.
During the server startup sequence, press the F9 key to access RBSU.
2.
Select the Advanced Options menu.
3.
Select Service Options.
4.
Select Serial Number. The following warnings appear:
WARNING! WARNING! WARNING! The serial number is loaded into the system during
the manufacturing process and should NOT be modified. This option should only
be used by qualified service personnel. This value should always match the
serial number sticker located on the chassis.
Warning: The serial number should ONLY be modified by qualified personnel.
This value should always match the serial number located on the chassis.
5.
Press the Enter key to clear the warning.
6.
Enter the serial number and press the Enter key.
7.
Select Product ID. The following warning appears:
Removal and replacement procedures
62
Warning: The Product ID should ONLY be modified by qualified personnel. This
value should always match the Product ID on the chassis.
8.
Enter the product ID and press the Enter key.
9.
Press the Esc key to close the menu.
10.
Press the Esc key to exit RBSU.
11.
Press the F10 key to confirm exiting RBSU. The server automatically reboots.
150W PCIe power cable option
WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment,
remove the power cord to remove power from the server. The front panel Power On/Standby
button does not completely shut off system power. Portions of the power supply and some internal
circuitry remain active until AC power is removed.
Disconnect the cable as indicated.
To replace the component, reverse the removal procedure.
HP Trusted Platform Module
The TPM is not a customer-removable part.
CAUTION: Any attempt to remove an installed TPM from the system board breaks or disfigures
the TPM security rivet. Upon locating a broken or disfigured rivet on an installed TPM,
administrators should consider the system compromised and take appropriate measures to ensure
the integrity of the system data.
If you suspect a TPM board failure, leave the TPM installed and remove the system board. Contact an HP
authorized service provider for a replacement system board and TPM board.
Removal and replacement procedures
63
Cabling
SAS drive cabling
Cabling 64
FBWC cabling
•
SFF FBWC cabling
•
PCIe option
Depending on the server configuration, you may need to remove the primary PCIe riser cage ("PCIe
riser cage (primary)" on page 31) before cabling to a PCIe expansion board.
Cabling 65
Diagnostic tools
Troubleshooting resources
The HP ProLiant Gen8 Troubleshooting Guide, Volume I: Troubleshooting provides procedures for resolving
common problems and comprehensive courses of action for fault isolation and identification, issue resolution,
and software maintenance on ProLiant servers and server blades. To view the guide, select a language:
•
English (http://www.hp.com/support/ProLiant_TSG_v1_en)
•
French (http://www.hp.com/support/ProLiant_TSG_v1_fr)
•
Spanish (http://www.hp.com/support/ProLiant_TSG_v1_sp)
•
German (http://www.hp.com/support/ProLiant_TSG_v1_gr)
•
Japanese (http://www.hp.com/support/ProLiant_TSG_v1_jp)
•
Simplified Chinese (http://www.hp.com/support/ProLiant_TSG_v1_sc)
The HP ProLiant Gen8 Troubleshooting Guide, Volume II: Error Messages provides a list of error messages
and information to assist with interpreting and resolving error messages on ProLiant servers and server
blades. To view the guide, select a language:
•
English (http://www.hp.com/support/ProLiant_EMG_v1_en)
•
French (http://www.hp.com/support/ProLiant_EMG_v1_fr)
•
Spanish (http://www.hp.com/support/ProLiant_EMG_v1_sp)
•
German (http://www.hp.com/support/ProLiant_EMG_v1_gr)
•
Japanese (http://www.hp.com/support/ProLiant_EMG_v1_jp)
•
Simplified Chinese (http://www.hp.com/support/ProLiant_EMG_v1_sc)
HP Insight Diagnostics
HP Insight Diagnostics is a proactive server management tool, available in both offline and online versions,
that provides diagnostics and troubleshooting capabilities to assist IT administrators who verify server
installations, troubleshoot problems, and perform repair validation.
HP Insight Diagnostics Offline Edition performs various in-depth system and component testing while the OS
is not running. To run this utility, boot the server using Intelligent Provisioning.
HP Insight Diagnostics Online Edition is a web-based application that captures system configuration and
other related data needed for effective server management. Available in Microsoft Windows and Linux
versions, the utility helps to ensure proper system operation.
For more information or to download the utility, see the HP website (http://www.hp.com/servers/diags). HP
Insight Diagnostics Online Edition is also available in the SPP.
Diagnostic tools
66
HP Insight Diagnostics survey functionality
HP Insight Diagnostics (on page 66) provides survey functionality that gathers critical hardware and software
information on ProLiant servers.
This functionality supports operating systems that are supported by the server. For operating systems
supported by the server, see the HP website (http://www.hp.com/go/supportos).
If a significant change occurs between data-gathering intervals, the survey function marks the previous
information and overwrites the survey data files to reflect the latest changes in the configuration.
Survey functionality is installed with every Intelligent Provisioning-assisted HP Insight Diagnostics installation,
or it can be installed through the SPP.
HP ROM-Based Setup Utility
RBSU is a configuration utility embedded in HP ProLiant servers that performs a wide range of configuration
activities that can include the following:
•
Configuring system devices and installed options
•
Enabling and disabling system features
•
Displaying system information
•
Selecting the primary boot controller
•
Configuring memory options
•
Language selection
For more information on RBSU, see the HP ROM-Based Setup Utility User Guide on the HP RBSU Information
Library (http://www.hp.com/go/rbsu/docs).
Integrated Management Log
The IML records hundreds of events and stores them in an easy-to-view form. The IML timestamps each event
with 1-minute granularity.
You can view recorded events in the IML in several ways, including the following:
•
From within HP SIM
•
From within operating system-specific IML viewers
o
For Windows: IML Viewer
o
For Linux: IML Viewer Application
•
From within the HP iLO user interface
•
From within HP Insight Diagnostics (on page 66)
Diagnostic tools
67
USB support and functionality
USB support
HP provides both standard USB 2.0 support and legacy USB 2.0 support. Standard support is provided by
the OS through the appropriate USB device drivers. Before the OS loads, HP provides support for USB
devices through legacy USB support, which is enabled by default in the system ROM.
Legacy USB support provides USB functionality in environments where USB support is not available normally.
Specifically, HP provides legacy USB functionality for the following:
•
POST
•
RBSU
•
Diagnostics
•
DOS
•
Operating environments which do not provide native USB support
Internal USB functionality
An internal USB connector is available for use with security key devices and USB drive keys. This solution
provides for use of a permanent USB key installed in the internal connector, avoiding issues of clearance on
the front of the rack and physical access to secure data.
External USB functionality
HP provides external USB support to enable local connection of USB devices for server administration,
configuration, and diagnostic procedures.
For additional security, external USB functionality can be disabled through RBSU.
Diagnostic tools
68
Component identification
Front panel components
Item
Description
1
Video connector
2
Serial pull tab
3
USB connector
4
Fan module
5
Hot-plug hard drive
6
Systems Insight Display
Front panel LEDs and buttons
Component identification 69
Item
Description
Status
1
NIC status LED
Solid green = Link to network
Flashing green (1 Hz/cycle per sec) = Network active
Off = No network activity
2
Health LED
Solid green = Normal
Flashing amber = System degraded
Flashing red (1 Hz/cycle per sec) = System critical
Fast-flashing red (4 Hz/cycles per sec) = Power fault*
3
Power On/Standby button
and system power LED
Solid green = System on
Flashing green (1 Hz/cycle per sec) = Performing power on sequence
Solid amber = System in standby
Off = No power present**
4
UID button/LED
Solid blue = Activated
Flashing blue (1 Hz/cycle per sec) = Remote management or
firmware upgrade in progress
Off = Deactivated
* To identify components in a degraded or critical state, see the Systems Insight Display LEDs, check iLO/BIOS logs, and
reference the server troubleshooting guide.
** Facility power is not present, power cord is not attached, no power supplies are installed, power supply failure has
occurred, or the power button cable is disconnected.
Systems Insight Display LEDs
The HP Systems Insight Display LEDs represent the system board layout. The display enables diagnosis with
the access panel installed.
Item
Description
Status
1
Over temp
Off = Normal
Solid amber = High system temperature
detected
Component identification 70
Item
Description
Status
2
NIC link/activity
Off = No link to network. If the power is off,
view the rear panel RJ-45 LEDs for status
("Rear panel LEDs and buttons" on page
73).
Flashing green = Network link and activity
Solid green = Network link
3
AMP status
Off = AMP modes disabled
Solid green = AMP mode enabled
Solid amber = Failover
Flashing amber = Invalid configuration
4
Power cap
Off = System is in standby, or no cap is set.
Solid green = Power cap applied
—
All other LEDs
Off = Normal
Amber = Failure
For more information on the activation of
these LEDs, see "Systems Insight Display
LED combinations (on page 71)."
Systems Insight Display LED combinations
When the health LED on the front panel illuminates either amber or red, the server is experiencing a health
event. Combinations of illuminated Systems Insight Display LEDs, the system power LED, and the health LED
indicate system status.
Systems Insight Display Health LED
LED and color
Processor (amber)
Red
System power
LED
Status
Amber
One or more of the following conditions may
exist:
•
•
•
•
Processor in socket X has failed.
Processor X is not installed in the socket.
Processor X is unsupported.
ROM detects a failed processor during
POST
Processor (amber)
Amber
Green
Processor in socket X is in a pre-failure
condition.
DIMM (amber)
Red
Green
One or more DIMMs have failed.
DIMM (amber)
Amber
Green
DIMM in slot X is in a pre-failure condition.
Overtemperature (amber)
Amber
Green
The Health Driver has detected a cautionary
temperature level.
Overtemperature (amber)
Red
Amber
The server has detected a hardware critical
temperature level.
Fan (amber)
Amber
Green
One fan has failed.
Fan (amber)
Red
Green
Two or more fans have failed or there is a
missing fan module.
Component identification 71
Systems Insight Display Health LED
LED and color
Power supply (amber)
Red
System power
LED
Status
Amber
•
•
•
Power supply (amber)
Amber
Green
•
•
•
•
Only one power supply is installed and
that power supply is in standby.
Power supply fault
System board fault
Redundant power supply is installed and
only one power supply is functional.
AC power cord is not plugged into
redundant power supply.
Redundant power supply fault
Power supply mismatch at POST or
power supply mismatch through hot-plug
addition.
Power cap (off)
—
Amber
Standby
Power cap (green)
—
Flashing green
Waiting for power
Power cap (flashing
amber)
—
Amber
Power cap has been exceeded
Power cap (green)
—
Green
Power is available
IMPORTANT: If more than one DIMM slot LED is illuminated, further troubleshooting is required.
Test each bank of DIMMs by removing all other DIMMs. Isolate the failed DIMM by replacing
each DIMM in a bank with a known working DIMM.
Rear panel components
Item
Description
1
PCIe slots 1–3 (top to bottom)
2
PCIe slots 4–6 (top to bottom)
3
Power supply 1 (PS1)
4
Power supply 1 power connector
5
Power supply 2 power connector
6
Power supply 2 (PS2)
7
USB connectors (4)
Component identification 72
8
Video connector
9
iLO connector
10
Serial connector
11
FlexibleLOM ports (Shown: 4x1Gb/Optional: 2x10Gb); port 1 on right side
Rear panel LEDs and buttons
Item
Description
Status
1
Power supply 1
LED
Off = System is off or power supply has failed.
Solid green = Normal
2
Power supply 2
LED
Off = System is off or power supply has failed.
Solid green = Normal
3
UID LED/button
Off = Deactivated
Solid blue = Activated
Flashing blue = System being managed remotely
4
NIC activity LED
Off = No network activity
Solid green = Link to network
Flashing green = Network activity
5
NIC link LED
Off = No network link
Green = Network link
Non-hot-plug PCIe riser board slot definitions
•
Primary riser cage connector, connected to processor 1 or the southbridge
Slot
PCIe 3-slot riser cage*
PCIe 2-slot x16 riser cage
1 - FL/FH
PCIe2 or PCIe3** x16 (16,8,4,2,1)
—
2 - HL/FH
PCIe2 or PCIe3** x8 (8,4,2,1)
—
3 - HL/FH
PCIe2 x8 (4,2,1)†
—
•
Secondary riser cage connector, connected to processor 2 (Processor 2 must be installed)
Slot
PCIe 3-slot riser cage*
PCIe 2-slot x16 riser cage
4 - FL/FH
PCIe2 or PCIe3** x16 (16,8,4,2,1)
PCIe2 or PCIe3** x16 (16,8,4,2,1)
Component identification 73
Slot
PCIe 3-slot riser cage*
PCIe 2-slot x16 riser cage
5 - HL/FH
PCIe2 or PCIe3** x8 (8,4,2,1)
PCIe2 or PCIe3** x16 (16,8,4,2,1)
6 - HL/FH
PCIe2 or PCIe3** x8 (8,4,2,1)
—
*Depending on the server model, the server might ship with one or two riser cages installed.
**These slots can run 8 GT/s signaling rate in either PCIe2 or PCIe3 mode, depending on the capability of the installed
processor.
†PCIe slot 3 is connected to the southbridge and runs at the Gen2 signaling rate.
Notes:
"Primary" denotes the riser cage is installed in the primary riser connector.
"Secondary" denotes the riser cage is installed in the secondary riser connector.
Installing the riser cages listed in the table above in either the primary or secondary riser connectors determines the form
factor of the PCIe boards supported by those riser cages.
FL/FH denotes full-length, full-height. HL/FH denotes half-length, full-height. LP denotes low profile.
The PCIe 2-slot x16 riser cage supports a maximum power of 150 W with an HP power cable. This cable must be used
for PCIe board wattages greater than 75 W.
System board components
Item
Description
1
Processor 3 DIMM slots (7-12)
2
Front power switch
Component identification 74
Item
Description
3
Processor 3 socket
4
Drive cage power connector 2
5
Processor 3 DIMM slots (1-6)
6
Systems Insight Display connector
7
Sideband signal connector
8
Processor 4 DIMM slots (7-12)
9
Processor 4 socket
10
Discovery services connector
11
Drive cage power connector 1
12
Front video connector
13
Processor 4 DIMM slots (1-6)
14
Processor 2 DIMM slots (1-6)
15
Power supply backplane connector
16
USB connector 1
17
System battery
18
MicroSD card slot
19
Internal USB connector
20
Secondary (processor 2) PCIe riser connector
21
TPM connector
22
Processor 2 socket
23
Processor 2 DIMM slots (7-12)
24
Processor 1 DIMM slots (1-6)
25
System maintenance switch
26
Primary (processor 1) PCIe riser connector
27
FlexibleLOM slot
28
SAS connector 1
29
USB connector 2
30
SAS connector 2
31
Cache module connector
32
Processor 1 DIMM slots (7-12)
33
Processor 1 socket
System maintenance switch
Position
Default
Function
S1
Off
Off = HP iLO security is enabled.
On = HP iLO security is disabled.
S2
Off
Off = System configuration can be
changed.
On = System configuration is locked.
S3
Off
Reserved
S4
Off
Reserved
S5
Off
Off = Power-on password is enabled.
On = Power-on password is disabled.
Component identification 75
Position
Default
Function
S6
Off
Off = No function
On = ROM reads system configuration
as invalid.
S7
—
Reserved
S8
—
Reserved
S9
—
Reserved
S10
—
Reserved
S11
—
Reserved
S12
—
Reserved
To access the redundant ROM, set S1, S5, and S6 to on.
When the system maintenance switch position 6 is set to the On position, the system is prepared to erase all
system configuration settings from both CMOS and NVRAM.
CAUTION: Clearing CMOS and/or NVRAM deletes configuration information. Be sure to
properly configure the server or data loss could occur.
NMI functionality
An NMI crash dump enables administrators to create crash dump files when a system is hung and not
responding to traditional debug mechanisms.
Crash dump log analysis is an essential part of diagnosing reliability problems, such as hangs in operating
systems, device drivers, and applications. Many crashes freeze a system, and the only available action for
administrators is to cycle the system power. Resetting the system erases any information that could support
problem analysis, but the NMI feature preserves that information by performing a memory dump before a
hard reset.
To force the OS to invoke the NMI handler and generate a crash dump log, the administrator can use the iLO
Virtual NMI feature.
For more information, see the HP website (http://www.hp.com/support/NMI).
Component identification 76
DIMM slot locations
DIMM slots are numbered sequentially (1 through 12) for each processor. The supported AMP modes use the
letter assignments for population guidelines.
Hot-plug drive bay numbering
Hot-plug drive LED definitions
Component identification 77
Item
LED
Status
1
Locate
Solid blue
The drive is being identified by a host application.
Flashing blue
The drive carrier firmware is being updated or requires an update.
Rotating green
Drive activity
Off
No drive activity
Solid white
Do not remove the drive. Removing the drive causes one or more of
the logical drives to fail.
Off
Removing the drive does not cause a logical drive to fail.
Solid green
The drive is a member of one or more logical drives.
Flashing green
The drive is rebuilding or performing a RAID migration, strip size
migration, capacity expansion, or logical drive extension, or is
erasing.
Flashing
amber/green
The drive is a member of one or more logical drives and predicts
the drive will fail.
Flashing amber
The drive is not configured and predicts the drive will fail.
Solid amber
The drive has failed.
Off
The drive is not configured by a RAID controller.
2
3
4
Activity ring
Do not remove
Drive status
Definition
PCIe riser cage LED
CAUTION: To prevent damage to the server or expansion boards, power down the server and
remove all AC power cords before removing or installing the PCI riser cage.
Status
On = AC power is connected.
Off = AC power is disconnected.
Component identification 78
FBWC module LEDs (P222, P420, P421)
The FBWC module has three single-color LEDs (one amber and two green). The LEDs are duplicated on the
reverse side of the cache module to facilitate status viewing.
1 - Amber
2 - Green
3 - Green
Interpretation
Off
Off
Off
The cache module is not powered.
Off
Flashing 0.5 Hz
Flashing 0.5 Hz
The cache microcontroller is executing from within its
boot loader and receiving new flash code from the host
controller.
Off
Flashing 1 Hz
Flashing 1 Hz
The cache module is powering up, and the capacitor
pack is charging.
Off
Off
Flashing 1 Hz
The cache module is idle, and the capacitor pack is
charging.
Off
Off
On
The cache module is idle, and the capacitor pack is
charged.
Off
On
On
The cache module is idle, the capacitor pack is charged,
and the cache contains data that has not yet been
written to the drives.
Off
Flashing 1 Hz
Off
A backup is in progress.
Off
On
Off
The current backup is complete with no errors.
Flashing 1 Hz
Flashing 1 Hz
Off
The current backup failed, and data has been lost.
Flashing 1 Hz
Flashing 1 Hz
On
A power error occurred during the previous or current
boot. Data may be corrupt.
Flashing 1 Hz
On
Off
An overtemperature condition exists.
Flashing 2 Hz
Flashing 2 Hz
Off
The capacitor pack is not attached.
Flashing 2 Hz
Flashing 2 Hz
On
The capacitor has been charging for 10 minutes, but
has not reached sufficient charge to perform a full
backup.
On
On
Off
The current backup is complete, but power fluctuations
occurred during the backup.
On
On
On
The cache module microcontroller has failed.
Hot-plug fans
Component identification 79
CAUTION: To avoid damage to server components, all fan modules must be installed in fan bays
for any processor configuration.
For all processor configurations, the HP ProLiant DL560 Gen8 Server requires six fan modules for
redundancy. A fan failure causes a loss of cooling redundancy. A second fan failure or a missing fan module
causes an orderly shutdown of the server.
The server supports variable fan speeds. The fans operate at minimum speed until a temperature change
requires a fan speed increase to cool the server.
The server shuts down in the following temperature-related scenarios:
•
At POST and in the OS, HP iLO performs an orderly shutdown if a cautionary temperature level is
detected. If the server hardware detects a critical temperature level before an orderly shutdown occurs,
the server performs an immediate shutdown.
•
When the Thermal Shutdown feature is disabled in RBSU, HP iLO does not perform an orderly shutdown
when a cautionary temperature level is detected. Disabling this feature does not disable the server
hardware from performing an immediate shutdown when a critical temperature level is detected.
CAUTION: A thermal event can damage server components when the Thermal Shutdown feature
is disabled in RBSU.
IMPORTANT: An immediate shutdown is a hardware-controlled function and it overrides any
firmware or software actions.
Component identification 80
Storage and expansion diagram
Component identification 81
Specifications
Environmental specifications
Specification
Value
Temperature range*
Operating
10°C to 35°C (50°F to 95°F)
Shipping
-30°C to 50°C (-22°F to 122°F)
Storage
-30°C to 60°C (-22°F to 140°F)
Maximum wet bulb
temperature
28°C (82.4°F)
Relative humidity
(noncondensing)**
Operating
10% to 90%
Non-operating
5% to 95%
* All temperature ratings shown are for sea level. An altitude derating of 1°C per 300 m (1.8°F per 1,000 ft) to 3048
m (10,000 ft) is applicable. No direct sunlight allowed.
** Storage maximum humidity of 95% is based on a maximum temperature of 45°C (113°F). Altitude maximum for
storage corresponds to a pressure minimum of 70 KPa.
Mechanical specifications
Specification
Value
Height
8.73 cm (3.44 in)
Depth
74.93 cm (29.50 in)
Width
44.54 cm (17.54 in)
Weight (maximum)
27.66 (61.00)
Weight (minimum)
18.59 (41.00)
Power supply specifications
The server is configured with the HP 1200 W CS HE Power Supply (94%) ("HP 1200 W CS HE Power Supply
(94%) specifications" on page 82).
HP 1200 W CS HE Power Supply (94%) specifications
Specification
Value
Input requirements
Rated input voltage
100 to 120 VAC, 200 to
240 VAC
Rated input frequency
50 Hz to 60 Hz
Specifications
82
Rated input current
9.1 A at 100 VAC
6.7 A at 200 VAC
Maximum rated input power
897 W at 100V AC input
1321 W at 200V AC input
Btus per hour
3408 at 120V AC input
4433 at 200V to 240V AC input
Power supply output
Rated steady-state power
800 W at 100V AC input
900 W at 120V AC input
1200 W at 200V to 240V AC
input
Maximum peak power
800 W at 100V AC input
900 W at 120V AC input
1200 W at 200V to 240V AC
input
Specifications
83
Acronyms and abbreviations
DDR
double data rate
FBWC
flash-backed write cache
iLO
Integrated Lights-Out
IML
Integrated Management Log
NMI
nonmaskable interrupt
NVRAM
nonvolatile memory
PCIe
Peripheral Component Interconnect Express
POST
Power-On Self Test
RBSU
ROM-Based Setup Utility
SAS
serial attached SCSI
SATA
serial ATA
TPM
Trusted Platform Module
Acronyms and abbreviations 84
UID
unit identification
USB
universal serial bus
Acronyms and abbreviations 85
Documentation feedback
HP is committed to providing documentation that meets your needs. To help us improve the documentation,
send any errors, suggestions, or comments to Documentation Feedback (mailto:[email protected]).
Include the document title and part number, version number, or the URL when submitting your feedback.
Documentation feedback
86
Index
1
150W PCIe power cable 63
A
expansion slot blanks 46, 47
extending server from rack 25
external USB functionality 68
F
battery 56
blank, power supply 35
buttons 23, 69
fans 37
FBWC cabling 65
FBWC capacitor pack 43
FBWC module 41, 79
FBWC procedures 41, 45
features 69
FlexibleLOM 38
front panel components 69
full-length expansion board 28, 47
C
H
cable management arm 27
cables 64
cabling 64
cautions 24
components 15, 69
components, identification 15, 69
connectors 69
CSR (customer self repair) 5
customer self repair (CSR) 5
hard drive bays 69, 77
hard drive blanks 34
hard drive LEDs 77
hard drives, determining status of 77
heatsink 48
hot-plug fans 27, 79
HP Insight Diagnostics 66, 67
HP technical support 5
AC power supply 35, 82
access panel 29
air baffle 29
B
D
data recovery 45
diagnostic tools 66
diagnostics utility 66
DIMM slot locations 77
DIMMs 55, 77
drive bays 77
drive LEDs 77
drives 34, 77
E
electrostatic discharge 23
environmental specifications 82
error messages 66
expansion board retainers 28
expansion boards 47
I
illustrated parts catalog 15
iLO (Integrated Lights-Out) 67
IML (Integrated Management Log) 67
Insight Diagnostics 66, 67
Integrated Lights-Out (iLO) 67
Integrated Management Log (IML) 67
internal USB functionality 68
L
LEDs 71, 77
LEDs, front panel 77
LEDs, hard drive 77
LEDs, SAS hard drive 77
LEDs, troubleshooting 78
Index
87
M
O
specifications, power 82
specifications, server 82
static electricity 23
symbols on equipment 23
system battery 56
system board components 74
system board replacement 57
system components 69
system maintenance switch 75
Systems Insight Display 27, 70, 71
Systems Insight Display LEDs 70, 71
optical drive 69
T
P
technical support 5
tools 23
TPM (Trusted Platform Module) 63
troubleshooting 66
maintenance 23
management tools 66
mechanical components 15
mechanical specifications 82
N
NIC connectors 72
part numbers 15
PCI expansion slots 73
PCIe riser blank 31
PCIe riser board 33
PCIe riser cage 31, 32
POST error messages 66
power cables 63
power supplies 35, 82
power supply 35
power supply backplane 36
power supply blank 35
power supply LEDs 73
power supply specifications 82
powering down 25
preparation procedures 24
processors 51
U
USB connector 69
USB support 68
utilities 66
V
video connector 69
W
warnings 24
R
rack bezel 30
RBSU (ROM-Based Setup Utility) 67
rear panel buttons 73
rear panel components 72
rear panel LEDs 73
rear panel, accessing 27
recovering the data from the cache 45
removal and replacement procedures 23
removing server from rack 26
S
safety considerations 23
spare part numbers 15
specifications 82
specifications, environmental 82
specifications, mechanical 82
Index
88
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement