Advertisement
Advertisement
User's manual
LC series
Title:
Date:
LC SERIES
April 2008
ProdID: R5976934
Revision: 08
This manual is divided into 13 chapters: main issue update
Warranty statement chapter 1 chapter 2 chapter 3 chapter 4 chapter 5 chapter 6 chapter 7 chapter 8 new: corr.: add.: chapter 9 chapter 10 chapter 11 chapter 12 chapter 13
-
-
Rev. 05
Rev. 03: new dimensions LC-47, rev. 06: new drawings
OSD update, rev. 06: OSD update (SDI/HD-SDI interface)
Rev. 09: Add: SDI/HD-SDI interface
Rev. 03: new dimensions LC-47, rev. 06: Add: SDI/HD-SDI interface
Rev. 07: new dimensions LCx-42, LCx47
Revised timing, rev. 06: SDI/HDSI timings
Rev. 03, FCC statement
Rev. 06, installation of accessories
The corresponding chapters are new or completely revised.
Passages of the corresponding chapter were corrected; see modification bars.
Passages of the corresponding chapter were added; see modification bars.
Document History
Modifications which result in a new version are indicated by a vertical bar.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
___________________________________________________________________________________________
i
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufacturers.
Copyright © 2005-2008 by Barco
Die Weitergabe sowie die Vervielfältigung aller Unterlagen, die von uns überlassen werden, deren Verwertung und Mitteilung ihres Inhaltes an Dritte ist nicht gestattet, soweit dies nicht ausdrücklich zugestanden ist. Urheberrechte, insbesondere auch solche an Software, werden nur insoweit übertragen, als es für die Erreichung des speziellen Vertragszwecks erforderlich ist. Zuwiderhandlungen können zu Schadensersatz verpflichten. Alle Rechte aus der Erteilung eines Patents oder der Eintragung eines Gebrauchsmusters verbleiben bei uns.
Copyright © 2005-2008 by Barco
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco. ii_____________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
Hardware warranty
The warranty period commences at the date of signature of the Certificate of Installation and Operation or as soon as the purchaser, customer or any other party occupies or operates the system, or 3 months after shipping in case no certificate of installation and Operation is provided.
• The Seller warrants the equipment manufactured by the Seller against defects in workmanship and material, under normal use and in accordance with its specifications, during the period of 24 months from the aforementioned date. Any part of the equipment which is wholly manufactured by third parties, is guaranteed under the conditions of such manufacturer and no separate warranty is given in respect thereof by the Seller.
• In the particular case of LCD displays, the warranty does not apply to the case of image retention phenomena (shadows, dark lines and other image artifacts), that may result from a usage outside of the following specification: in the course of 24 hours, the monitor can be used for maximum 2 shifts of 8 hours, with minimum 1 hour of relaxation between the shifts.
• In the event of a defect in workmanship or material, the Seller will be obliged, at its choice and best effort base, to replace or repair the defective equipment. The replacement part will be in good working order and at least functionally equivalent to the item replaced.
• The warranty does not apply when the cause of the failure occurs after delivery of the equipment to the
Purchaser and results from abnormal conditions of operation, unauthorized access, improper use, unauthorized modification, lack of normal maintenance or unauthorized attempts to repair the equipment. See also
Pre installation requirements and conditions of use BCD system. A failure to follow these requirements can result in delay and additional costs that will be invoiced to the purchaser.
• The Purchaser must notify the Seller of any complaint within eight days of discovery of any alleged defect.
Failure by the Purchaser to so notify the Seller will relieve the Seller of its obligations under this article.
• The foregoing warranty will not apply if any payment remains outstanding from the Purchaser to the Seller.
• All items, parts or components which are replaced by the Seller under warranty or otherwise shall become the property of the Seller. All defective parts need to be sent back to the Seller.
• The replacement parts are free of charge during the warranty period.
• The Seller will ship the replacement parts to the Purchaser on a CIF base. At the same time the Seller will issue a RAN number for returning the defective parts.
• Traveling and Lodging of the service engineer will be invoiced to the Purchaser according to the Time & Material Pricing rules of the Seller.
• On site labor of the service engineer will be invoiced to the Barco National Organization or Sales Partner according to the Time & Material Pricing rules of the Seller.
• The remedies described above are Purchaser's sole remedies in the event of any breach of the warranty provided above.
• Consumables (such as lamps, dust filters, ...) are excluded from warranty.
• The warranty period of repairs and spare parts is 3 months, or at minimum the original warranty period of the system.
• The seller does no warrant uninterrupted or error-free operation of the installation
• The foregoing warranty is in lieu of all other warranties, whether oral, written, express, implied or statutory.
No implied or statutory warranties of merchantability or fitness for a particular purpose shall apply and all warranties, conditions or other terms implied by statute or common law are hereby excluded.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_________________________________________________________________________________________
iii
Software warranty
The Seller makes no warranties with respect to the software and technical information and, such items are provided to the Purchaser on an "as-is" basis without warranty of any kind, including the warranties of merchantability and fitness for a particular purpose.
• The Purchaser acknowledges and agrees that the software provided by the Seller to the Purchaser in an unmodified form is designed to operate with the hardware identified in the Certificate of Installation and
Operation, provided (i) the hardware is unmodified and (ii) the software, as unmodified, operates in conjunction with the proper computer equipment as designated in the Special Conditions.
• The Purchaser agrees to indemnify, defend and hold harmless the Seller from and against all claims, liabilities, losses, damages and costs and expenses arising out of or resulting from the combination or integration of the hardware and/or software with any item of any kind not furnished by the Seller. iv ____________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
Revision sheet
To:
An der Rossweid 5, D-76229 Karlsruhe
Phone: +49-721-6201-0, Fax: +49-721-6201-298
E-mail: [email protected], Web: www.barcocontrolrooms.de
From:
Date:
Please correct the following points in this documentation: page wrong correct
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
__________________________________________________________________________________________
v
Contents
vi ____________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5.6.2 Baud rate.......................................................................................................................................... 5-36
5.6.3 Light Sensor ..................................................................................................................................... 5-37
5.6.4 Lower brightness level .................................................................................................................... 5-37
5.6.5 Ambient light threshold .................................................................................................................. 5-37
5.6.6 Auto Source Selection...................................................................................................................... 5-38
5.8.1 Input selection with the function key F1........................................................................................ 5-44
6.1 Cleaning .......................................................................................................................................................6-2
7 Technical data 42" version (LCN-42, LCS-42) .................................................................................... 7-1
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_________________________________________________________________________________________
vii
9 Compliant timing ............................................................................................................................... 9-1
9.1 SDI input signals ..........................................................................................................................................9-2
9.2 HD-SDI input signals ....................................................................................................................................9-3
10 Troubleshooting ............................................................................................................................. 10-1
10.1 Faults....................................................................................................................................................... 10-2
10.2 Contact .................................................................................................................................................... 10-3
11 Compliance statement................................................................................................................... 11-1
11.1 FCC Compliance statement .................................................................................................................... 11-1 viii ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12.2 Table stand ............................................................................................................................................. 12-2
12.2.1 Scope of delivery ........................................................................................................................... 12-2
12.3.1 Scope of delivery ........................................................................................................................... 12-6
12.3.2 Installation ..................................................................................................................................... 12-7
12.4 Fixed wall mount.................................................................................................................................... 12-8
12.4.1 Scope of delivery ........................................................................................................................... 12-8
12.4.2 Installation ..................................................................................................................................... 12-9
12.4.4 Wall pattern ................................................................................................................................. 12-11
12.5 Tiltable wall mount .............................................................................................................................. 12-12
12.5.2 Installation ................................................................................................................................... 12-13
12.5.3 Dimensions .................................................................................................................................. 12-14
12.6.1 Scope of delivery ......................................................................................................................... 12-17
12.6.2 Installation ................................................................................................................................... 12-18
12.6.3 Dimensions .................................................................................................................................. 12-20
12.6.4 Tilting ........................................................................................................................................... 12-21
12.7 Long ceiling mount............................................................................................................................... 12-22
12.7.1 Scope of delivery ......................................................................................................................... 12-23
12.7.2 Installation ................................................................................................................................... 12-24
12.7.3 Dimensions .................................................................................................................................. 12-26
12.7.4 Tilting ........................................................................................................................................... 12-27
13 Contact ........................................................................................................................................... 13-1
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_________________________________________________________________________________________
ix
1. Preliminary Remarks
1 Preliminary Remarks
This manual describes unpacking, installation, cabling and controlling of the monitors of Barco's LC series.
The monitors of Barco's LC series are based on Super MVA TFT LCD technology and feature bright and wide images with clear contrast.
The LCD panels have 1920x1080 pixels (HD resolution) to allow extreme fine pictures at 16.7 millions colors.
The monitors provide a set of interfaces to connect any analog video and analog and digital RGB data .
All settings can easily be accessed and modified by means of the Infrared remote control unit and the
OnScreenDisplay.
RS232 remote control is also possible.
The monitors are available with a screen diagonal of 42" and 47".
LCN-47
LCS-47
LCN-42
LCS-42
Monitor with a screen diagonal of 47inch, Super MVA TFT LCD technology, HD resolution (1920x1080 pixels), aspect ratio 16:9
Monitor with a screen diagonal of 47inch, Super MVA TFT LCD technology, HD resolution (1920x1080 pixels), aspect ratio 16:9, HD-SDI input
Monitor with a screen diagonal of 42inch, Super MVA TFT LCD technology, HD resolution (1920x1080 pixels), aspect ratio 16:9
Monitor with a screen diagonal of 42inch, Super MVA TFT LCD technology, HD resolution (1920x1080 pixels), aspect ratio 16:9, HD-SDI input
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
1-1
1. Preliminary Remarks
1.1 How this manual is organized
This manual is divided into 13 chapters:
• Preliminary remarks explains the structure of the manual itself and the used typographic styles and symbols. Safety information is provided concerning the monitors of Barco's LC series.
• Unpacking and Installation gives instructions how to unpack the monitors and general installation requirements
• Design and function provides a technical description of the equipment listing the fundamental characteristics and functional principles. Knowledge of this section is not absolutely essential for operation.
• Controlling explains how the monitors are controlled
• The On Screen Display explains the commands of the menus
• Maintenance and servicing explains how the equipment can be serviced.
• Technical data of the 42" versions provides tabular overviews about the technical details of the monitor LCN-42 and LCS-42
• Technical data of the 47" versions provides tabular overviews about the technical details of the monitor LCN-47 and LCS-47
• Compliant timing lists the compliant timing of the monitor
• Trouble shooting gives hints in case the monitor does not work
• Compliance statement
Includes the FCC statement
• Accessories lists the available accessories and their installation
• Contact lists address details of the help desk
Chapters, pages, and tables are numbered separately. Chapters are indicated by a »point syntax«, e. g. 4.2.3, pages and tables by a »dash syntax«, e. g. 2-1.
1-2 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
1. Preliminary Remarks
1.2 Styles and symbols
The typographic styles and the symbols used in this document have the following meaning:
Bold Labels, menus and buttons are printed in Bold font.
Condensed Links to both other chapters of this manual and to sites in the Internet are printed condensed . In the on-line version of this manual all hyperlinks appear teal .
Courier Names of files and parts from programs are printed in the Courier font.
Courier bold Inputs you are supposed to do from the keyboard are printed in Courier bold font.
If you do not heed instructions indicated by this symbol there is a risk of damage to the equipment!
If you do not heed instructions indicated by this symbol there is a risk of electrical shock and danger to personal health!
If you do not heed instructions indicated by this symbol there is a risk of damage to parts, which are sensitive towared electrostatic charge!
If you do not heed instructions indicated by this symbol there is a risk to get harmed by sharp objects!
If you do not heed instructions indicated by this symbol there is a risk that parts may explode!
If you do not heed instructions indicated by this symbol there is a risk that hot parts impact persons or objects!
The sheet icon indicates additional notes.
Next to this icon you find further information.
This hand marks tips.
Next to this icon you find important notes.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
1-3
1. Preliminary Remarks
1.3 Safety information
This section describes safety precautions which must be observed when installing a product from Barco.
Safety standards
The safety standards of information technology equipment impose important requirements on the use of safety critical components, materials and isolation, in order to protect the user or operator against the risk of electric shock and energy hazard, and having access to live parts.
Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability and strength, enclosure construction and protection against risk of fire.
Simulated single fault condition testing ensures the safety of the equipment to the use even when the equipment’s normal operation fails.
General safety instructions
• All the safety and operating instructions should be read before using this unit.
• The operating instructions manual should be retained for future reference.
• All warnings on the device and in the documentation manuals should be adhered to.
• All instructions for operating and use of this equipment must be followed precisely.
• All local installation codes should be adhered to.
Installation and preliminary adjustments should be performed by qualified Barco personnel or authorized Barco service dealers.
1.3.1 Safety on installation
Check the power rating on your outlet before connecting the devices to the wall outlet or to a power strip. Contact your facilities manager or a qualified electrician if you are not sure what type of power is supplied to your building.
The devices are designed to operate with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.
A. Mains lead (AC Power cord) with CEE 7 plug:
The colors of the mains lead are colored in accordance with the following code:
Green-and-yellow: Earth (safety earth)
Blue:
Brown:
Neutral
Line (live)
1-4 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
1. Preliminary Remarks
B. Power cord with NEMA 15-5 plug:
The wires of the power cord are colored in accordance with the following code:
Green or green/yellow: Ground
White or blue:
Black or brown:
Neutral
Line (live)
• Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord.
• To disconnect the cord, pull it out by the plug. Never pull the cord itself.
• If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating. Also make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.
• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock.
• Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before resuming operations.
• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the monitor due to lightning and AC power-line surges.
Warning: Do not place flammable or combustible materials near the monitor!
Transportation
• Any transportation of the unopened unit in its packaging should be done by two persons.
• In transportation or storage of products in original packing, NEVER stack more than the number stated on the carton box. This warning is also indicated on the side of the card box.
• For transportation or storage, observe the warnings and instructions on the side of the card box.
Nearby equipment
If air conditioning ducts or lamps, etc. are located near the installation site, the attendant dust, extreme temperatures, humidity, and condensation may become sources of trouble. Please take sufficient steps to avoid this.
Safety locations
Do not install the unit where it may be easily touched or leaned against. Avoid locations subject to high vibrations or severe impacts. Do not install the unit where it is exposed to humidity, oil, smoke or excessive dust.
Mechanical stress.
Please be careful not to apply strong mechanical stress (shock, drop) to the LCD module. Such stress may cause break of screen glass and lamp or may be the cause for failure.
Pressure to screen surface.
Please be careful not to apply strong pressure to the screen surface. Such pressure may cause scratches at the surface or may be the cause of failure.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
1-5
1. Preliminary Remarks
Protection against scratch.
Please be careful not to hit, press or rub the screen surface with hard material like tools. In addition, please do not put heavy or hard material on the screen surface, and do not stack monitors. Polarizer at the front surface can be easily scratched.
Temperature dependence of the display.
Response speed (optical response) of the LCD display is dependent on temperature. Under low temperature, response speed is slower. Also brightness and chromaticity change slightly depend on temperature.
Image retention
Displaying the same pattern for a long time may cause image sticking, vertical dark lines or other forms of image artifacts. This is a common phenomenon of all LCD displays. It disappears after some time if the pattern is changed, or the monitor is switched off. However, image retention is not subject of warranty.
For more information contact Barco for a white paper on this topic.
Lightning conditions
Consider existing lightning and sunlight angles when creating the installation layout. Extremely bright lightning can reduce the visibility and the quality of the displayed image.
In extremely bright surroundings, adjusting screen intensity may not result in perceptibly brighter images. Keep in mind that extreme intensity settings can reduce system service life.
Barco products are designed and manufactured to meet the most stringent safety regulations. Exposing flammable or combustible materials into close proximity of this device could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an "exclusion zone" around all external surfaces of the monitor whereby no flammable or combustible materials are present. The exclusion zone must be not less than 10 cm (4"). Do not cover the monitor with any material while it is in operation.
Keep flammable and combustible materials away from the monitor at all times. Mount the monitor in a well ventilated area away from sources of ignition and out of direct sun light. Never expose this product to rain or excessive moisture. In the event of fire, use sand, CO
2
, or dry powder fire extinguishers; never use water on an electrical fire.
Always have service performed on this product by authorized Barco service personnel. Always insist on genuine
Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this device.
Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety tested at the factory and may not be used to power the display. For a replacement power cord, contact your dealer.
Slots and openings in the cabinet and the sides are provided for ventilation; to ensure reliable operation of the device and to protect it from overheating, these openings must not be blocked or covered. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
1-6 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
1. Preliminary Remarks
1.3.2 Safety on servicing
Do not attempt to service this device yourself, as opening or removing covers may expose you to dangerous voltage potential and risk of electric shock! Refer all monitor service to a qualified Barco service center.
Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
Call for service in the following conditions:
• When the power cord or plug is damaged or frayed.
• If liquid has been spilled into the device.
• If the product has been exposed to rain or water.
• If the product does not operate normally when the operating instructions are followed.
• If the product has been dropped or the cabinet has been damaged;
• If the product exhibits a distinct change in performance, indicating a need for service.
Replacement parts
When replacement parts are required, be sure the service technician has used original Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty.
Safety check
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.
Protection
Please do not disassemble or modify the LCD module to avoid the possibility of electric shock, damage of electronic components, scratch at display surface and invasion of foreign particles. In addition, such activity may result in fire accident due to burning of electronic component.
The LCD module disassembled or modified by customer is out of warranty.
Please be careful in handling of display with broken glass. When the display glass breaks, please pay attention not to injure your fingers. The display surface has the plastic film attached, which prevents dispersion of glass pieces; however touching broken edge will injure your fingers. Also the lamp (Cold Cathode Fluorescent Lamp) is made of glass, therefore please pay attention in the same way.
Please do not touch the fluid flown out of broken display glass. If the fluid should stick to hand or clothes, wipe off with soap or alcohol immediately and then wash it with water.
If the fluid should get in your eyes, wash your eyes immediately with pure water for more than 15 minutes and then consult the doctor.
The lamp contains mercury inside. Please follow the regulations or rules established by local authorities at its disposal..
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
1-7
1. Preliminary Remarks
1.3.3 Safety on shipping
Original shipping package
Save the original shipping packing material; they will come in handy if you ever have to ship one of your installed modules. For maximum protection, repack your set as it was originally packed at the factory.
1.3.4 Precautions
For your own protection, observe the following safety precautions!
• Observe all warnings and instructions printed on the devices!
• Check that the voltage and frequency of your power supply match those printed on the device label with the rated electrical values!
• Servicing not explicitly mentioned in this manual should never be carried out by unauthorized personnel!
• Some parts of the body are hot during operation. Please be careful.
• In case of moving long-distance, wrap the unit with blanket to avoid damages. Be careful not to bump the unit.
• Do not spray
Unused for long periods of time
For added protection for this video product during a lightning storm, or when it is left unattended an unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the LCD module due to lightning and AC power-line surges
1.3.5 Malfunction or Trouble
Trouble
Smoke or peculiar smells comes from the unit
No picture or sound
Water is spilled or objects are dropped inside the unit
The unit is dropped or the cabinet is damaged
The power cord or plug is damaged or becomes hot take the following steps
Remove the power plug from the outlet immediately!
Make sure that the smoke or smell has stopped, then contact your dealer for inspection
Remove the power plug from the outlet immediately!
Contact your dealer for inspection
Remove the power plug from the outlet immediately!
Contact your dealer for inspection
Remove the power plug from the outlet immediately!
Contact your dealer for inspection
Power off the unit with the power switch on the rear side.
When the power plug has cooled down, remove the power plug from the wall outlet!
Contact your dealer for inspection risk of fire or an electric shock fire or an electric shock fire or an electric shock fire or an electric shock fire or an electric shock
1.3.6 Unpacking of devices
Note advises on the packaging for unpacking!
Please refer to chapter
1-8 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
1. Preliminary Remarks
1.3.7 Modification of devices
Mechanical or electrical modifications others than described in this manual must not be made to the devices.
Barco is not liable for damages resulting from modified devices.
Only authorized personnel should carry out other maintenance work not explicitly mentioned in this user's manual!
Never open the case of the monitor without first disconnecting the power supply cord!
Measurements and tests with an opened device may be carried out only in the factory or by specially trained personnel, due to the dangers of electrical shock.
1.3.8 Disposal or handing over to a new owner
• Do not mix with other general waste.
• Do not dispose the LCD monitor in waste treated by a waste treatment center.
The lamp contains mercury inside. Please follow the regulations or rules established by local autorithies at its disposal..
1.3.9 Exemptions
• This monitor is not liable for any damage caused by natural disaster (such as earthquake, thunder, etc.), fires, acts by third parties, accidents, owner’s intentional misuse and fault, or uses in other improper conditions.
• This monitor is not liable for incidental damages (such as profit loss or interruption in business, modification or erasure of record data, etc.) caused by use or inability to use of this product.
• This monitor is not liable for any damage caused by neglect of the instructions described in the owner’s manual.
• This monitor is not liable for any damage caused by misuse or malfunction through simultaneous use of this product and the connected equipment or software.
• This monitor is not liable for any damage caused by neglect of the instructions described about the installation stand in the owner’s manual.
• This monitor is not liable for any damage caused by improper installation.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
1-9
2 Unpacking and installation
2. Unpacking and installation
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
2-1
2. Unpacking and installation
2.1 Unpacking
The monitor is surrounded with foam for transportation protection and packed into a card box. Banding and fastening clips secure the package.
To unpack the monitor,
• Release the fastening clips
• Remove the banding
• Take the monitor out
• Remove the foam.
For later shipment, it is recommended to store the original packaging and to re-use it.
The following components are included in the delivery:
• The monitor itself
• 1 pc power cord (European, with CEE7 power plug)
• 1 pc power cord (American, with NEMA 15-5 (ANSI 73.11) power plug)
• 1 pc user's manual
• 1 pc Infra red remote control unit
• 1 pc RCA jack
• 1 pc DVI-D 24 pin cable
• 1 pc D-Sub 15 pin cable
• 1 pc S-Video Mini Din 4 pin cable
• 1 pc cable adapter Mini Din 8 pin to 3xRCA jack (for component video)
2-2 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
2. Unpacking and installation
2.2 Installation
Installation and preliminary adjustments should be performed by qualified Barco personnel or authorized Barco service dealers.
Installation of the monitor shall comply with the safety instructions as listed in chapter
• Make sure that the installation place has sufficient stability!
• Do not place the monitor near heat sources!
• Use maximum 15mm/0.59 inch long screws. Longer screws may damage the monitor!
• Ensure that the display is operating within the specified operating range +5°C – +40°C | 41°F – 104°F, at max.
90% RH, non-condensing.
• Never restrict airflow into the display by blocking any vents or air intakes.
• Leave a clearance on all vented sides of the display to permit the required airflow. Clearance should be minimum 15 cm but may be larger depending on the ambient environment.
Do not install the unit where it may be easily touched or leaned against. Avoid locations subject to high vibrations or severe impacts. Do not install the unit where it is exposed to humidity, oil, smoke or excessive dust.
2.2.1 Accessories
The product portfolio of accessories comprises a table stand, and wall and ceiling mounts. The installation of the accessories is described in the installation section. The following chapter just gives a rough idea about mounting the table stand.
2.2.2 Mounting of the table stand (optional)
The table stand is an optional component.
The monitors feature on their rear side 2 parallel arrangements of 4 threads each. These threads comply with the
VESA standards, their horizontal and vertical distance is 200mm. They are equipped with the respective screws
(M8x15).
These screws are used to attach the table stand!
• Lay the monitor upside down on a clean(!) surface, bottom edge flush with e.g. edge of the table.
Soil or particles laying on the surface may irretrievably damage the screen of the monitor!
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
2-3
2. Unpacking and installation
• Take a screwdriver for recessed head screws, size 8.
• Remove the 4 center screws and washers on the rear side of the monitor.
• Take the table stand and attach its mounting plate to the rear of the monitor using the previously removed screws and washers.
Mind the correct orientation of the table stand!
• When the screws are fastened tightly, put up the monitor
2-4 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
2.2.3 Dimensions of the 42" monitor:
2.2.3.1 Front view
2. Unpacking and installation
2.2.3.2 Side view and rear view:
123.7
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
2-5
2. Unpacking and installation
2.2.4 Dimensions of the 47" monitor:
2.2.4.1 Front view
1139.4
2.2.4.2 Side view and rear view:
125
2-6 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
2. Unpacking and installation
2.3 Examining the monitor
2.3.1 Front view
An LED on the bottom right edge indicates the operating status of the monitor.
LED indicator
Orange
Green
Mode
Standby
In operation
Next the to LED indicator the sensor to receive the commands from the IR control unit is located as well as the
light sensor to determine the surrounding light intensity.
Take care that the sensors are not blocked by any objects placed in front of the monitor!
2.3.2 Side view
ENTER
>/+
</-
Menu
The control elements of monitors are located on the right (seen from front). The 7 push buttons allow switching the monitor from and to standby, to adjust volume and to activate and operate the OSD.
Refers to Item
1
2
3
4
5
6
7
ENTER
>/+
</-
Menu
Function
Standby / switch into operation
Activate selection
Scroll right for menu items / volume increase
Scroll left for menu items / volume decrease
Scroll down for menu ite
ms /
Access signal input menu
Scroll up for menu items
OSD control menu button / Access or exit main menu /
Access or exit submenu / Exit selection
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
2-7
2. Unpacking and installation
2.3.3 Rear view
On the rear, all interfaces as well as the power connector and the main power switch are located.
The standardized power socket is conform to IEC-320-13 and allows connecting local power cables. The internal power supply is auto ranging from 100VAC to 240VAC.
The monitor allows connecting the following sources:
Input
Video system input
RGB input
HD-SDI input *)
HD-SDI output *)
Signal receive&transmit
Audio
VIDEO IN
S-VIDEO
Interface
RCA
S-Video Mini Din 4pin signals
NTSC/PAL
NTSC/PAL
YUV (Y Pb/Cb Pr/Cr) Component Mini Din 7 pin NTSC/PAL
RGB Analog D-Sub 15 pin RGB analog
RGB Digital
Serial Digital
DVI-D 24 pin
BNC
RGB digital
SDI / HD-SDI
Serial Digital
RS232 IN
RS232 OUT
BNC
D-Sub 9 pin
D-Sub 9 pin
RCA
(red: right (R), white: left (L))
SDI / HD-SDI
Audio in (L+R)
Audio out(L+R) (2x) and
Subwoofer
The pin assignments of the interfaces are listed in chapter
respectively.
HDSDI/SDI IN HDSDI/SDI OUT RS232/OUT RS232/IN
L/OUT1 L/OUT2 L/IN MAIN POWER AC IN
VIDEO
IN
S-VIDEO
Y
Pb/Cb
Pr/Cr DVI RGB IN
ON
OFF
SW R/OUT1 R/OUT2 R/IN
Two sources can be viewed simultaneously in either PIP mode (Picture-in-Picture) or PAP mode (Picture-and-
Picture). In case more than one source is connected, the active sources and the display mode (one source or two sources) are selected via the OSD.
*)
Only LCS-42 and LCS-47 feature the HD-SDI interfaces!
2-8 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
2. Unpacking and installation
2.4 Cabling
All interfaces are located on the rear of the system!
Check the power rating on your outlet before connecting the monitor to the wall outlet or to a power strip. Contact your facilities manager or a qualified electrician if you are not sure what type of power is supplied to your building.
The devices are designed to operate with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.
• Use the power cord delivered with your system:
• Plug in the female power connector into the male connector AC IN on the rear of the monitor.
• Plug in the CEE7-plug (or ANSI 73.11 plug) into the wall outlet.
The power input is auto-ranging from 100VAC to 240 VAC.
• Connect the video and RGB sources with the respective interface using the included cables.
2.5 Switching on and off
Use the main power switch on the rear of the system to power the system on and off.
When the monitor is powered on, it can be switched into operation or switched to standby, respectively, using eater the top most push button on the rear right side of the monitor or using the IR remote control unit (RCU).
If the system is not operated for longer periods, it is recommended to switch it off using the main power switch on the rear side and to disconnect it from the wall outlet.
When the monitor is powered off by switching off the main power switch, the front LED indicating the operating mode is off! Also you cannot switch the unit into operation by using the remote control unit or the top most push button.
To power on the unit, switch on the main power switch on the rear of the system. The LED indicator will be turned on, and you can switch the monitor into operation either by using the RCU or the top most push button the rear of the system.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
2-9
2. Unpacking and installation
2.6 Inserting batteries into the Infrared remote control unit
The batteries are not yet inserted in the remote control to avoid remote control operation in its package, resulting in a shorter battery lifetime.
How to install the batteries:
• Push the cover tab with the fingernail a little backwards (as indicated by the arrow) and pull upwards the cover top.
• Slide the cover forwards to remove-
• Insert two AA size batteries, making sure the polarities match the + and – marks inside the battery compartment.
• Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until it clicks in place
Note that there may be laws concerning disposal and recycling of used batteries in your country! Please contact your local authorities to get further information!
Avoid keeping used, old batteries inside the remote control, causing leakage of internal liquid resulting metal rust or fatal damage to the remote control unit.
2-10 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
3 Design and function
This chapter introduces the systems and explains some of their characteristics.
3. Design and function
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
3-1
3. Design and function
3.1 Display of choice
The state-of-the-art monitors deliver crisp, clear images detailed to perfection. Compatible with a wide variety of signal sources, they are capable of showing analog video as well as data content.
Sources and interfaces
The monitor provides interfaces to connect composite video, S-Video, component video as well as analog or digital RGB.
Picture-in-Picture
Two of the connected sources can be displayed simultaneously, either next to each other (PAP: picture-andpicture), or one source embedded in the other (PIP: picture in picture).
The sources can be controlled individually (brightness, contrast, color)
Automatic brightness adjustment
A light sensor determines the surrounding light intensity. According the measurement, the panel will adjust to one of the two preset brightness levels: bright mode or dim mode.
User friendliness
The monitors can intuitively be operated and controlled via the OSD and the Infra Red Remote Control Unit (IR
RCU).
The language of the OSD can be selected as well as its position on the screen, size, etc.
RS232 remote control is also possible.
In case you want to operate the monitor via RS232 Remote Control, contact Barco about the protocol!
3-2 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
3. Design and function
3.2 Technology
The monitors are based on LCD Super MVA technology. The benefits of this technology are wide viewing angles, fast video response and high contrast ratio.
MVA stands for Multidomain Vertical Alignment.
3.2.1 Principle of LCD technology
These are the basics used in LCD technology:
• Light can be polarized
• Liquid crystals can transmit polarized light.
• Liquid crystals align themselves when a voltage is applied.
• Liquid crystals change the light's plane of vibration to match their own angle.
There are multiple operating principles of LCD's; one of them is the Multidomain Vertical Alignment which – not surprising – is based on the Vertical Alignment (VA) technology.
With this operating principle, the LC molecules are completely perpendicular when no voltage is applied, and thus they don't change the polarization of light. Light simply passes the LC, and is blocked by the front end polarizer (since this polarizer is rotated 90° against the back end polarizer which allowed the incident light to pass).
Because the blockage is complete, the quality of black produced this way is excellent!
When voltage is applied, the molecules shift to a horizontal position, producing a white image: the polarization of the light is changed, and light can pass the front end polarizer.
Since the LC molecules are simply switched between vertical and horizontal alignment, response speeds are very fast.
As a further development of the VA technology, with MVA technology the LC cell is divided in sub domains where the molecules are oriented in opposite direction. This widens the viewing angles and enhances the performance.
The following picture shows the basic principle of VA technology:
V=0
V=Vmax backlight back polarizer substrate liquid crystal substrate front polarizer full black full white
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
3-3
4 Controlling
4. Controlling
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
4-1
4. Controlling
4.1 General
The monitors can be controlled via the 7 push buttons at the right or conveniently remote-controlled by the infrared remote control unit (RCU).
In case you want to use RS232 Remote Control, contact Barco!
The push buttons as well as the IR RCU make use of the OSD: the menu is displayed, a menu item is selected and/or changed. Subsequently the OSD is closed again.
4
5
6
2
3
4.1.1 The push buttons
The push buttons are located on the right rear side of the monitor. The seven buttons are arranged in a vertical row and have the following functions:
Push button
1 (top most)
7
Refers to Function
Standby / switch into operation
ENTER
>/+
</-
Menu
Activate selection
Scroll right for menu items / volume increase
Scroll left for menu items / volume decrease
Scroll down for menu items
Scroll up for menu items
OSD control menu button / Access Main /
Sub-menu / Quick Menu Selection
4-2 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
4. Controlling
4.1.2 The IR remote control unit
The remote control is used for control, adaptation and source selection. It is also used to switch between standby and operational mode.
The remote control unit (RCU) includes a battery powered infrared (IR) transmitter that allows the user to control the monitor remotely.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
4-3
4. Controlling
7
8
9
10
11
12
13
14
15
16
4.2 Terminology of the RCU controls
2
3
1
4
5
6
17
18
Function keys
F1
F2
F3
F4
F5
ADJ
Address key
Source selection
PIP control setting
Switch between master source and PIP source
In VGA mode: White balance
Shows the RS232 address of the monitor
ADJUST key, to enter the OSD has no function for this monitor
Selection key
PAUSE
Standby
Switch the light sensor on/off
Change baud rate of the serial interface stand by button, to start the monitor when the power switch is switched on and to switch off the monitor without switching off the power switch.
Switch off and on the sound (audio) Mute
Help
Digit buttons
Indicates the resolution of the input video signal
0-9: have no function for this monitor
Audio controls To control volume, balance, bass and treble of the audio signal
Picture controls Except for brightness and contrast, these keys have no function for this monitor
PHASE
Freeze
TEXT
ENTER
Cursor Keys
Adjust the phase of the signal
Auto adjust
Switch on/off the 4:3 mode to confirm an adjustment or selection
EXIT
RC operating indication to make menu selections in the OSD.
RCU cursor key up cursor key down cursor key right cursor key left
Use the cursor keys up or right for increasing a value.
Use the cursor keys down or left for decreasing a value. to leave a menu or the OSD lights up when a button on the remote control is pressed. (This is a visual indicator to check the operation of the remote control)
How to use the RCU?
Point the front of the RCU directly at the screen.
When using the IR remote control, make sure you are within the effective operating distance
(30m, 100ft in a straight line). The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control unit and the IR sensor.
4-4 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
4. Controlling
4.3 Functions available with the IR Remote Control Unit
4.3.1 Displaying a monitor address
The default (factory) address of a monitor is 1.
With the IR remote control unit, all monitors with any address can be controlled.
With RS232 remote control, the monitors can be controlled individually if they had received a unique display address. (This address can be displayed by means of the function key F5 on the IR remote control unit).
Press F5 on the IR remote control unit to display the assigned address of the monitor.
4.3.2 Baud rate setting
The default baud rate for RS232 communication is 115200 baud. The baud rate can be set in the OSD, cf.
With the PAUSE key on the IR RCU the baud rate can directly be set to 115200, 38400, 19200, or 9600, respectively. Press PAUSE to display the currently set baud rate. Press PAUSE again to switch the baud rate to the next lower setting. In case the baud rate is 9600, the next setting will be 115200.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
4-5
4. Controlling
4.3.3 The function keys
Using the function keys, the respective OSD command will immediately be executed.
For information about the commands, please refer to the respective section in the OSD description.
Function key Description refers to
F1
F2
F3
F4
Source selection
PIP control setting
Switch between master source and PIP source, the source assigned to input 1 will be assigned to input 2 and vice versa
In VGA mode: White balance
5.8.1 Input selection with the function key F1 ,
F5 Display the monitor address
This command has no equivalent in the
OSD: when e.g. a signal looks greenish, pressing the function key F4 will correct and adjust the color impression.
4.3.4 Picture controls with direct access.
Brightness and contrast can be controlled directly via IR RCU. When Brightness or Contrast is pressed, the respective OSD dialog pops up to allow the adjustment.
4.3.5 Audio controls with direct access.
Volume, balance, bass and treble can be controlled directly via IR RCU. When the respective keys on the IR remote control unit are pressed,, the respective OSD dialog pops up to allow the adjustment.
Please refer to respective section of the OSD description, cf. 5.5 Audio setting menu
4-6 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5 The On Screen Display (OSD)
5. The On Screen Display (OSD)
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
5-1
5. The On Screen Display (OSD)
5.1 General
The monitors feature an OSD which allows selecting the input, to adjust the sources, to modify OSD settings, etc.
When activating the OSD, the main menu is displayed.
Except for the function keys and the direct access keys, it is always the main menu which is the entry level for any modification.
The main menu is activated by pressing ADJ on the RCU or by pressing push button 7 (the bottom most push button the right rear side).
A selected menu item shows a blue background, an unselected menu item a gray background.
A selected menu entry looks like a button and it is indicated with a blue dot.
The current status of the menu entry shows a blue background.
If a value has been modified, it will definitely be applied when quitting the dialog (even when pressing EXIT!)
Therefore it is recommended to write down the values: there is no UNDO to a single operation, only the global factory reset.
Grayed out menus or items are not available with the current configuration.
5-2 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.1.1 Navigation and adjustment
RCU
• Press the ADJ key to activate the OSD
• Use the left and right cursor keys to navigate to a menu
Icon Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to a menu
Except for signal 1 and signal 2, the menus do not have a submenu.
Menus without a submenu display their settings dialog as soon as they are activated!
• Press Enter to select a menu with a sub menu: the menu icon will turn blue
• Press 2 to select a menu with a sub menu: the menu item will turn blue
• Use the left and right cursor keys to navigate to a submenu
• Press 3 and 4 to navigate to a sub menu
• Press Enter to select: the item will turn blue – or –
• Press the down cursor key:
• Use the up and down cursor keys to navigate to the entries of a dialog.
The entry will get a "button look" and a blue dot.
• In case an option is linked to a button: use the left and right cursor keys to select one of the options
• In case increase/decrease is linked to a
"slider": use the left and right cursor keys to decrease/increase a value – or –
• In case increase/decrease is linked to a button: use the Enter key to decrease/increase a value
• Press 2 to select: the item will turn blue – or –
• Press 5
• Press 5 and 6 to navigate to the entries of a dialog
The entry will get a "button look" and a blue dot.
• In case an option is linked to a button: use the push buttons 3 / 4 to select one of the options
• In case increase/decrease is linked to a "slider": use the push buttons 3
/ 4 to decrease increase a value – or –
• In case increase/decrease is linked to a button: use the push button 2 to increase/decrease a value
As soon as a menu entry loses the focus, i.e. another entry is selected, the respective selection will be applied without any further action: even when quitting the dialog with Exit, the modification will be applied!
• Press Exit to deactivate the dialog • Press 7 to deactivate the dialog
• Press Exit to leave a sub menu
• Use the left and the right cursor key to navigate to another menu
• Press 7 to leave a sub menu
• Use 3 and 4 to navigate to another menu
• Press Exit to close the OSD • Press 7 to close the OSD
Closing a first level dialog (i.e. a dialog linked to a menu, not to a sub menu) by means of the Exit key / the push button 7 will close the OSD!
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
5-3
5. The On Screen Display (OSD)
5.2 Activating the OSD
The OSD can be activated and operated by means of the IR remote control unit (RCU) or the push buttons at the right rear side of the monitor.
RCU
• Press the ADJ key to activate the OSD
Icon
-
Push button (1: top most)
• Press 7 to activate the OSD
Then the main menu is displayed (default: on the upper left corner of the monitor).
The OSD will be displayed at the position and size as defined in the OSD setting menu. If no modifications have been made via this menu, the OSD will pop up in the upper left corner of the monitor in normal mode (not Zoomed In, background opaque)
Icon description signal menu for the first input, to select and control the settings of a source
The currently assigned signal is indicated in the label beneath
Signal menu for the second input, to select and control the settings of a source
The currently assigned signal is indicated in the label beneath
OSD setting menu, to control the position, transparency and time out of the OSD
Audio setting menu, to adjust volume, balance, bass and treble
Parameter setting menu, to set display address, baud rate, light sensor, lower brightness level, ambient light threshold & auto source selection
Reset menu, to reset to factory defaults. It also shows runtime & serial number of the display
5-4 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
To activate a menu, proceed as follows:
RCU
• Use the left and right cursor key to select a menu
• Menus without a submenu will turn blue and display their settings dialog
• Menus with a sub menu will turn blue and require an additional key stroke to open the settings dialog:
Use Enter to open the signal setting submenu
Use the down cursor key to open the signal selection dialog
Icon
-
Push button (1: top most)
• Use the push buttons 3, 4 to select a menu
• Menus without a submenu will turn blue and display their settings dialog
• Menus with a sub menu will turn blue and require an additional key stroke to open the settings dialog:
Use 2 to open the signal setting submenu
Use 5 to open the signal selection dialog
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
5-5
5. The On Screen Display (OSD)
5.3 The signal menu (first and second input)
The signal menu allows to control and adjust the settings of the source
The commands can be applied for the first input and for the second input, respectively.
Please note: the Image setting and Position setting is only available for the first (active) input!
In case more than one source is connected, the signal for input1 and input2 has to be assigned, cf.
.
5.8 Input Signal Selection The signal for input1 can also be selected via the
function key F1, 5.8.1 Input selection with the function key F1
RCU
• Press the ADJ key
• Use the left and right cursor keys to navigate to the signal menu
• Press Enter to select
Icon Push button (1: top most) input1 input2 • Press 7
• Press 3 and 4 to navigate to the
signal menu
• Press 2 to select
• Press 3 and 4 to navigate to Display • Use the left ad right cursor keys to navigate to Display
• Press Enter to select • Press 2 to select
The following sections will use the signal menu of the first input. For the second input, the same dialogs are displayed, however some items are deactivated (Image, Position)
Nevertheless the dialogs may look different: some commands depend on the type of the source. But this is independent from being input1 or input2!
The source menu button will turn blue. Subsequently the source sub menu opens with the items Display,
Position, PIP Control, Image, and Color
Image is only enabled for the source which is assigned to the first input!
The commands of Position are only enabled for the first input!
5-6 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.3.1 Display
On the Display dialog, brightness and contrast as well as hue, saturation, flesh tone can be adjusted (for VGA sources only: also black level adjustment)
To activate the Display dialog, proceed as follows:
RCU
• Press the ADJ key to activate the OSD
• Use the left and right cursor keys to navigate to the signal menu
• Press Enter to select
Icon Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to the
signal menu
• Press 2 to select
• Use the left and right cursor keys to navigate to Display
• Press Enter to select – or –
• Press the down key to activate the dialog
• Press 3 and 4 to navigate to Display
• Press 2 to select – or –
• Press 5 to activate the dialog
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
5-7
5. The On Screen Display (OSD)
5.3.1.1 Brightness
Brightness can be adjusted in the range between 0 and 100.
LCD panel screens are lit with built-in fluorescent tubes above, beside and sometimes behind the LCD (Cold Cathode Fluorescent Lamp, CCFL). This light is adjusted using the Brightness setting.
How brightness is perceived depends on the environment and on the content being viewed, which means that switching a source and/or the ambient light could require re-adjustment of brightness.
H
ow bright a pixel is perceived depends on both, brightness setting and contrast setting: brightness setting affects all levels from white to black at once. Contrast setting affects all but black.
RCU
• Use the up and down cursor keys to navigate to the Brightness
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Brightness
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
5.3.1.2 Contrast
Contrast can be adjusted in the range between 0 and 100.
The information content of a picture is related to contrast, not to brightness. The ratio between the brightest white and the darkest black that a display can produce in a completely dark room is called the full field contrast ratio.
Push button (1: top most)
• Press 5 and 6 to navigate to Contrast
RCU
• Use the up and down cursor keys to navigate to the Contrast
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
5-8 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.3.1.3 Hue
Hue can be adjusted in the range between -45 and +45.
The color = hue is most noticeable in areas of white.
There are multiple color models, one of them is the HSV model describing color as hue (color), saturation (the amount of white light in the color), and V (value, the amount of black/lightness/brightness).
With PAL, part of the color information on the video signal is reversed in phase with each line, which automatically corrects phase errors in the transmission of the signal.
With NTSC, the Hue control allows to perform the correction manually and to adjust the color
RCU
• Use the up and down cursor keys to navigate to the Hue
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Hue
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
5.3.1.4 Saturation
Saturation can be adjusted in the range between 0 and 100.
Saturation adjusts the amount of white light in the color.
RCU
• Use the up and down cursor keys to navigate to the Saturation
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Saturation
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
5.3.1.5 Flesh tone
Flesh tone can be switched off, or turned on weak, soft, or strong.
When in bright areas of the pictures the skin-tones show chalky white, the normal skin tone color can be restored.
RCU
• Use the up and down cursor keys to navigate to the Flesh tone
• Use the left and right cursor keys to select one of the options Off, Weak, Soft, Strong
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Flesh tone
• Use 3 and 4 to select one of the options Off,
Weak, Soft, Strong
The selection value is visualized by a white caption.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
5-9
5. The On Screen Display (OSD)
5.3.1.6 Black level (only available for analog RGB)
Black level can be adjusted in the range between 0 and 100.
The black level is the deepest black of the monitor.
RCU
• Use the up and down cursor keys to navigate to the Black Level
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Black Level
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
5-10 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.3.2 Position
On the Position dialog, the vertical and horizontal position of the image can be set as well as an area for zooming defined.
RCU
• Press the ADJ key to activate the OSD
• Use the left and right cursor keys to navigate to the signal menu
• Press Enter to select
Icon Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to the
signal menu
• Press 2 to select
• Use the left and right cursor keys to navigate to Position
• Press Enter to select – or –
• Press the down key to activate the dialog
• Press 3 and 4 to navigate to
Position
• Press 2 to select – or –
• Press 5 to activate the dialog
The entries of Position are only enabled for the signal assigned to input 1.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-11
5. The On Screen Display (OSD)
5.3.2.1 Zoom
Zoom can be selected to In and Out.
Zoom In
means to magnify the displayed picture. The magnification factor is related to the number of times the
In
button is activated. (The reverse operation is
Zoom Out
which reduces the picture back to the previous size).
The center of the original picture content will be "fixed" in the center of the monitor.
Due to the magnification, no longer the entire frame of the picture is displayed. To select the part of the frame to be viewed, use the commands Zoom Horizontal Pan and Zoom Vertical Pan. Activating the Left/Right button and the Down/Up button respectively resembles using the horizontal and vertical scrollbar to move the desired portion of the picture content into the active window.
Each activation of the button means moving the picture 5 pixels in the selected direction.
RCU
• Use the up and down cursor keys to navigate to the Zoom
• Use the left and right cursor keys to select one of the options In, Out.
The current value is visualized by a white caption.
• Use the Enter to increase/decrease the zoom factor.
Push button (1: top most)
• Press 5 and 6 to navigate to Zoom
• Use 3 and 4 to select one of the options In, Out.
The current value is visualized by a white caption.
• Use 2 to increase/decrease the zoom factor
Zoom Horizontal Pan and Zoom Vertical Pan is only available if the picture has been
Zoomed In, i.e. has been magnified and the display can no longer show the entire content of the picture frame.
5.3.2.2 Zoom Horizontal Pan
Zoom Horizontal Pan can be selected to Left and Right
RCU
• Use the up and down cursor keys to navigate to the Zoom Horizontal Pan
• Use the left and right cursor keys to select one of the options Left, Right.
The current selection is visualized by a white caption.
Push button (1: top most)
• Press 5 and 6 to navigate to Zoom Horizontal
Pan
• Use 3 and 4 to select one of the options Left,
Right
The current selection is visualized by a white caption.
• Use the Enter to move the picture content in the desired direction.
• Use 2 to move the picture content in the desired direction.
5-12 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.3.2.3 Zoom Vertical Pan
Zoom Vertical Pan can be set to Up and Down
RCU
• Use the up and down cursor keys to navigate to the Zoom Vertical Pan
• Use the left and right cursor keys to select one of the options Up, Down.
The current selection is visualized by a white caption.
• Use the Enter to move the picture content in the desired direction.
Push button (1: top most)
• Press 5 and 6 to navigate to Zoom Vertical Pan
• Use 3 and 4 to select one of the options Up,
Down
The current selection is visualized by a white caption.
• Use 2 to move the picture content in the desired direction.
5.3.2.4 Vertical
Vertical can be adjusted in the range from 0 and 255.
Vertical and Horizontal moves the screen content within the allocated position ("centered window") of the monitor. It is not possible to move e.g. a PAL Video (720x540) with display mode 1:1 to the upper left corner of the monitor: the allocated position is in the range 600pixel to 1320pixel (horizontal, counting started on the top left corner) and in the range 270pixel to 810pixel (vertical, counting started on the top left corner).
RCU
• Use the up and down cursor keys to navigate to the Vertical.
• Use the left and right cursor keys to move the picture content in steps of 1
The current value is indicated.
Push button (1: top most)
• Press 5 and 6 to navigate to Vertical.
• Use 3 and 4 to move the picture content in steps of 1
The current value is indicated.
The value is applied without any further action, e.g. the picture content is shifted in the desired direction.
5.3.2.5 Horizontal
Horizontal can be adjusted in the range from 0 and 255.
RCU
• Use the up and down cursor keys to navigate to the Horizontal.
• Use the left and right cursor keys to move the picture content in steps of 1
The current value is indicated.
Push button (1: top most)
• Press 5 and 6 to navigate to Horizontal.
• Use 3 and 4 to move the picture content in steps of 1
The current value is indicated.
The value is applied without any further action, e.g. the picture content is shifted in the desired direction.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-13
5. The On Screen Display (OSD)
5.3.3 PIP control
On the PIP CONTROL dialog, the vertical and horizontal position of the image can be set as well as an area for the embedded picture be defined.
PIP means picture-in-picture and displays dual moving images from two separate sources (e.g., PC and video) at the same time.
There are two different ways: one source is displayed in full size, and the other one is displayed in a small size overlaying the full screen picture. The full screen picture is called master source, and the other one PIP source.
Besides this display mode, the two sources can be displayed "side to side", which is called PAP mode (picture and picture).
The source selected on input 1 is always the master source, the source selected on input 2 is always the PIP source.
The master source and the PIP source can be switched by means of the function key F3 on the RCU (which in fact is changing sources at the inputs).
PIP settings made with input 2 are only applied when input 2 becomes the PIP master!
5-14 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
To activate the PIP CONTROL dialog, proceed as follows:
RCU
• Press the ADJ key to activate the OSD
• Use the left and right cursor keys to navigate to the signal menu
• Press Enter to select
Icon
• Use the left and right cursor keys to navigate to PIP control
• Press Enter to select – or –
• Press the down key to activate the dialog
Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to the
signal menu
• Press 2 to select
• Press 3 and 4 to navigate to PIP
Control
• Press 2 to select – or –
• Press 5 to activate the dialog
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-15
5. The On Screen Display (OSD)
5.3.3.1 PIP Mode
PIP Mode can be set to off, single, PAP.
When PIP mode is Off, only one source is displayed.
When PIP mode is Single, the source connected to input 1 is the master source and displayed according its settings, whereas the source connected to input 2 is the PIP source and displayed either in Small, Medium or Large size according the PIP Size selections.
The position of the PIP source is set using the Vertical and Horizontal adjustment.
PIP Size, Vertical and Horizontal are only enabled if PIP Mode is selected Single.
In case no source is connected to input 2,
Single will result in an empty window with blue borders,
PAP will result in displaying source1 at the left half of the monitor (right half remains black).
RCU
• Use the up and down cursor keys to navigate to the PIP Mode
• Use the left and right cursor keys to select one of the options Off, Single, PAP
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to PIP Mode
• Use 3 and 4 to select one of the options Off,
Single, PAP
The current selection is visualized by a white caption.
Using the direct access key F2, the selected PIP mode can be toggled between On and Off.
Using the direct access key F3, the PIP master and the PIP source can be toggled.
5.3.3.2 PIP Size
PIP size can be set to small, medium, and large.
RCU
• Use the up and down cursor keys to navigate to the PIP Size
• Use the left and right cursor keys to select one of the options Small, Medium, Large.
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to PIP Size
• Use 3 and 4 to select one of the options Small,
Medium, Large. The current selection is visualized by a white caption.
5-16 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.3.3.3 Vertical
Vertical can be adjusted in the range from 0 to 255.
RCU
• Use the up and down cursor keys to navigate to the Vertical
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
(increase: move down/decrease: move up)
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Vertical
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
(increase: move down/decrease: move up)
5.3.3.4 Horizontal
Horizontal can be adjusted in the range from 0 to 255.
RCU
• Use the up and down cursor keys to navigate to the Horizontal
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
(increase: move right/decrease: move left)
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Horizontal
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
(increase: move right/decrease: move left)
5.3.4 Combination of signals for main image and PiP/PaP
The following table lists the combination of signals for input 1 (main input) and input 2 (PiP/PaP). Not all combinations are possible; some cause disturbances or result in images which are not properly scaled.
Input 1
VGA
DVI
Input 2
DVI
HD-SDI 1 or HD-SDI 2
S-Video or Composite or Component
VGA
Comment only possible for low resolutions, higher resolutions cause an error message
(Pixel rate > 110MHz), not recommended with Barco Transform H system.
OK
OK
HD-SDI 1 or HD-SDI 2
S-Video or Composite or Component only possible for low resolutions, higher resolutions cause an error message
(Pixel rate > 110MHz), not recommended with Barco Transform H system.
OK
OK
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-17
5. The On Screen Display (OSD)
Input 1
HD-SDI 1 or HD-SDI 2
S-Video or Composite or Component
Input 2
VGA or DVI
S-Video or Composite or Component
VGA or DVI
HD-SDI 1 or HD-SDI 2
Comment
OK
Not possible
OK
Not possible
5.3.5 Image
On the Image dialog, the settings of the signal can be optimized.
For best image results, use short cables between the source and the monitor!
The image dialog depends on the source:
In case of analog RGB, the image settings comprises Scaling, Auto adjust, Phase, and Clock.
In case of S-Video/Video, the image settings comprise Scaling, Noise Reduction, Angle Filter, Film Mode Detect,
Sharpness.
In case of a DVI, due to the digital interface, no adjustment is required. Therefore the dialog only comprises Scaling-
Image is only enabled for the source assigned to input 1!
To do the image adjustment for the source of input 2, this source has to be assigned to input 1.
To activate the Image dialog, proceed as follows:
RCU
• Press the ADJ key to activate the OSD
• Use the left and right cursor keys to navigate to the signal menu
• Press Enter to select
Icon Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to the
signal menu
• Press 2 to select
• Use the left and right cursor keys to navigate to Image
• Press Enter to select – or –
• Press the down key to activate the dialog
• Press 3 and 4 to navigate to Image
• Press 2 to select – or –
• Press 5 to activate the dialog
5-18 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5.3.5.1 Analog RGB
5. The On Screen Display (OSD)
Scaling
Scaling can be set to Native, Fill, Aspect, and 4:3.
Scaling means changing the resolution of an image.
Native is only enabled when the detected resolution of the source is lower than the resolution of the monitor.
'The monitor has a resolution of 1920x1080 pixel. In case the resolution of the source is lower (e.g. a PAL Video with 720x540 pixels), when displayed 1:1, there will be a black border around the content.
In case Fill is selected, the content is displayed on the entire screen which, in case the ratio of the source is different from the ratio of the screen (e.g. a PAL Video, 4:3), results in a distortion of the content: with PAL, in horizontal direction, the pixels would be multiplied by a factor of 2.6, whereas in vertical direction the factor would be 2.0.
With Aspect, the aspect ratio of the source is maintained: in the above mentioned example, the pixels both in horizontal and in vertical direction would be multiplied by a factor of two, thus the content would have a black border of 240 pixels both, on the left side and on the right side.
4:3
: if a PAL/NTSC source is connected to an input, the 4:3 setting displays the source without any distortion (e.g. a circle remains a circle).
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-19
5. The On Screen Display (OSD)
RCU
• Use the up and down cursor keys to navigate to the Scaling
• Use the left and right cursor keys to select one of the options Native, Fill, Aspect, 4:3.
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Scaling
• Use 3 and 4 to select one of the options Native,
Fill, Aspect, 4:3.
The current selection is visualized by a white caption.
Auto Adjust
When Auto Adjust is selected, the monitor adjusts itself to the timing of the source which matches best one of the internal preset timings.
Use the key FREEZE on the remote control unit to immediately start Auto Adjust.
During the Auto Adjust process, the monitor displays an information "Auto Configuration".
In case Auto Adjust is not selected, or the results are not perfect, the timing of the source has to be manually adjusted to the timing of the monitor using the controls Phase and
Clock.
Both controls are to minimize the interferences (noise). Clock is course adjustment whereas Phase is fine tuning of the setting.
To do the adjustment, use a test pattern (e.g. vertical stripes) of the connected source!
RCU
• Use the up and down cursor keys to navigate to the Auto Adjust
• Use the left and right cursor keys to select
Select
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Auto Adjust
• Use 3 and 4 to select Select
The current selection is visualized by a white caption.
5-20 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
Phase
Phase can be adjusted in the range from 0 to 255.
It is recommended to have the monitor warmed up for about 5 minutes before adjusting phase.
Use the Phase adjustment to eliminate shimmering horizontal streaking.
If there are not only horizontal streaking but also vertical banding, start with Clock adjustment!
RCU
• Use the up and down cursor keys to navigate to the Phase
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
Push button (1: top most)
• Press 5 and 6 to navigate to Phase
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action. Check the test pattern!
Clock
Clock can be adjusted in the range from 0 to 255.
It is recommended to have the monitor warmed up for about 5 minutes before adjusting clock.
Use the Clock adjustment to eliminate broad vertical banding.
RCU
• Use the up and down cursor keys to navigate to the Clock
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
Push button (1: top most)
• Press 5 and 6 to navigate to Clock
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action. Check the test pattern!
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-21
5. The On Screen Display (OSD)
5.3.5.2 S-Video
5-22 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
Scaling
Scaling can be set to Native, Fill, Aspect, and 4:3..
Scaling means changing the resolution of an image.
Native is only enabled when the detected resolution of the source is lower than the resolution of the monitor.
'The monitor has a resolution of 1920x1080 pixel. In case the resolution of the source is lower (e.g. a PAL Video with 720x540 pixels), when displayed 1:1, there will be a black border around the content.
In case Fill is selected, the content is displayed on the entire screen which, in case the ratio of the source is different from the ratio of the screen (e.g. a PAL Video, 4:3), results in a distortion of the content: with PAL, in horizontal direction, the pixels would be multiplied by a factor of 2.6, whereas in vertical direction the factor would be 2.0.
With Aspect, the aspect ratio of the source is maintained: in the above mentioned example, the pixels both in horizontal and in vertical direction would be multiplied by a factor of two, thus the content would have a black border of 240 pixels both, on the left side and on the right side.
4:3
: if a PAL/NTSC source is connected to an input, the 4:3 setting displays the source without any distortion (e.g. a circle remains a circle).
RCU
• Use the up and down cursor keys to navigate to the Scaling
• Use the left and right cursor keys to select one of the options Native, Fill, Aspect, 4:3.
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Scaling
• Use 3 and 4 to select one of the options Native,
Fill, Aspect, 4:3.
The current selection is visualized by a white caption.
Adaptive Deinterlacing
Adaptive deinterlacing can be selected to off, level 1, level 2, level 3.
Select the appropriate level of adaptive deinterlacing to optimize the quality of the video.
RCU
• Use the up and down cursor keys to navigate to the Adaptive Deinterlacing
• Use the left and right cursor keys to select one of the options Off, Level 1, Level 2, Level 3
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Adaptive
Deinterlacing
• Use 3 and 4 to select one of the options Off,
Level 1, Level 2, Level 3
The current selection is visualized by a white caption.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-23
5. The On Screen Display (OSD)
Noise Reduction
Noise reduction can be selected to off, low, medium, or high.
Noise is generally visible as "snow", or small dots that make the picture look fuzzy, With
Noise Reduction
the amount of noise attenuation can be specified.
RCU
• Use the up and down cursor keys to navigate to the Noise Reduction
• Use the left and right cursor keys to select one of the options Off, Low, Medium, High
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Noise Reduction
• Use 3 and 4 to select one of the options Off, Low,
Medium, High
The current selection is visualized by a white caption.
Angle Filtering
Angle filtering can be selected to on or off.
RCU
• Use the up and down cursor keys to navigate to the Angle Filtering
• Use the left and right cursor keys to select one of the options Off, On
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Angle Filtering
• Use 3 and 4 to select one of the options Off, On
The current selection is visualized by a white caption.
5-24 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
Film Mode Detect
Film Mode Detect can be selected to be on or off.
Film is usually recorded at 24 frames per second. When converting film to NTSC video (59.94 Hz field rate), 2 film frames generate 5 video fields (3:2 pull down). Film scenes with high-speed motion objects thus may show motion artifacts.
With Film Mode Detect on, the conversion to NTSC is detected and the original film frames are recreated by blending the fields back together.
(3:2 pull down is only one of the pull down techniques and used as an example)
RCU
• Use the up and down cursor keys to navigate to the Film Mode Detect
• Use the left and right cursor keys to select one of the options Off, On
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Film Mode Detect
• Use 3 and 4 to select one of the options Off, On
The current selection is visualized by a white caption.
This function may cause undesired effects on standard sources, therefore it can be disabled
(OFF) at any time.
Sharpness
Sharpness can be set in the range from -15 to +29
The edges are localized and the contrast between neighboring pixels enhanced.
RCU
• Use the up and down cursor keys to navigate to the Sharpness
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Sharpness
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-25
5. The On Screen Display (OSD)
5.3.6 Color
On the Color dialog, the gamma correction factor can be selected as well as the color temperature.
To activate the Color dialog, proceed as follows:
RCU
• Press the ADJ key to activate the OSD
• Use the left and right cursor keys to navigate to the signal menu
• Press Enter to select
Icon Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to the
signal menu
• Press 2 to select
• Use the left and right cursor keys to navigate to Color
• Press Enter to select – or –
• Press the down key to activate the dialog
• Press 3 and 4 to navigate to Color
• Press 2 to select – or –
• Press 5 to activate the dialog
5-26 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.3.6.1 Gamma Correction
The Gamma correction factor can be set to 2.2, 1.9, 2.5, and user.
Gamma is the relationship between the color values of the data and the color values displayed e.g. on a screen.
The Gamma coefficient makes it possible to adjust the brightness of the midtones only without affecting the very bright and very dark areas..
If gamma is set too high, middle tones appear too dark. If it's set too low, middle tones appear too light.
Using Barco’s DCMS software (display consistency management software), the monitor can be calibrated and the calibrated setting (look-up table, LUT) can be saved in the monitor. The gamma setting "user" activates the last calibrated value.
RCU
• Use the up and down cursor keys to navigate to the Gamma Correction
• Use the left and right cursor keys to select one of the options 2.2, 1.9, 2.5, user. The current selection is visualized by a white caption.
Push button (1: top most)
• Press 5 and 6 to navigate to Gamma Correction
• Use 3 and 4 to select one of the options 2.2, 1.9,
2.5, user.
The current selection is visualized by a white caption.
The selection is applied without any further action.
5.3.6.2 Color Temperature
Color temperature can be selected to be 3200K, 5400K, 6500K, 9300K or custom (User, requires to adjust the values for red, green, and blue).
Color temperature stands for the spectral properties of a light source.
Low color temperature implies warmer (more yellow/red) light while high color temperature implies a colder
(more blue) light.
The pictures of a monitor set to 9300K will look more bluish than if set to 3200K.
The following color temperature pre-sets can be selected:
Color temperature
3200K
5400K
6500K
9300K
User name / application
Broadcast
Film
Video
Computer custom
Push button (1: top most)
• Press 5 and 6 to navigate to Color Temperature
RCU
• Use the up and down cursor keys to navigate to the Color Temperature
• Use the left and right cursor keys to select one of the options 3200K, 5400K, User, 6500K,
9300K.
The current selection is visualized by a white caption.
The selection is applied without any further action.
• Use 3 and 4 to select one of the options 3200K,
5400K, User, 6500K, 9300K.
The current selection is visualized by a white caption.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-27
5. The On Screen Display (OSD)
When User is selected, the values for red, green, blue can be individually be adjusted:
RCU
• Use the up and down cursor keys to navigate to the Color Temperature
Push button (1: top most)
• Press 5 and 6 to navigate to Color Temperature
• Use the left and right cursor keys to select User • Use the left and right cursor keys to select User
• Use the down and up cursor keys to select Red,
Green, Blue
• Use the 5 and 6 to select Red, Green, Blue
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
The selection is applied without any further action.
Manual modification of R, G, B requires some experience!
In case a VGA signal looks e.g. greenish, pressing the function key F4 (White balance) will probably correct this. Thus no sophisticated color adjustment will be required.
5-28 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.4 OSD setting menu
On the OSD dialog, the position of the OSD can be defined as well as zoom, blend and time out of the OSD.
To activate the OSD menu, proceed as follows:
RCU
• Press the ADJ key to activate the OSD
• Use the cursor keys to navigate to the OSD
setting menu
• The icon will turn blue, and the setting dialog will pop up
Icon Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to the
OSD setting menu
• The icon will turn blue, and the setting dialog will pop up
Each time the OSD opens, its position and behavior will be as set on this dialog.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-29
5. The On Screen Display (OSD)
5.4.1 Vertical
The value can be set in the range form 0 to 255 (zero: top of OSD is level with top of monitor, 255: bottom of
OSD is level with bottom of monitor).
RCU
• Use the up and down cursor keys to navigate to the Vertical
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
(increase: move down)
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Vertical
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
(increase: move down)
Vertical and Horizontal define the position of the OSD. Whenever the OSD is activated, it will be displayed at the position defined by the vertical and horizontal setting.
5.4.2 Horizontal
The value can be set in the range form 0 to 255 (zero: left of OSD is level with left of monitor, 255: right of OSD is level with right of monitor).
RCU
• Use the up and down cursor keys to navigate to the Horizontal
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
(increase: move right)
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Horizontal
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
(increase: move right)
5.4.3 Blend
The value can be set in the range form 0 to 15 (zero: opaque, 15: transparent)
Use Blend to set the transparency of the OSD: when it Blend is set to zero, the background of the OSD will be opaque thus entirely hiding the screen content at this position. To make the screen content visible in spite of the overlaying OSD, increase the Blend parameter!
RCU
• Use the up and down cursor keys to navigate to the Blend
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Blend
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
5-30 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.4.4 Time out
The value can be set between 0 and 60 seconds in steps of 5 seconds.
The OSD will close (disappear) automatically when no selections are made during a certain time. This period can be set by means of the Time out parameter.
The OSD stays active as long as it is in use.
Independent from the Time out setting, you can close the OSD at any time by using the Exit button the RCU or the push button 7 on the right rear side of the monitor.
RCU
• Use the up and down cursor keys to navigate to the Time out
• Use the left and right cursor keys to increase/decrease the value in steps of 5
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Time out
• Use 3 and 4 to increase/decrease the value in steps of 5
The current value is indicated.
5.4.5 OSD Zoom
Zoom can be selected in or out.
This command will magnify the OSD window and the icons by approx. the factor of 2.
RCU
• Use the up and down cursor keys to navigate to the OSD Zoom
• Use the left and right cursor keys to select one of the options In, Out
The current selection is visualized by a white caption.
• Apply the selection with Enter.
This selection has to be confirmed to be applied.
Push button (1: top most)
• Press 5 and 6 to navigate to OSD Zoom
• Use 3 and 4 to select one of the options In, OUt
The current selection is visualized by a white caption.
• Apply the selection with 2
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-31
5. The On Screen Display (OSD)
5.5 Audio setting menu
On the Audio setting menu, the volume and the balance of the left/right speaker can be adjusted as well as bass and treble (low frequencies and high frequencies).
To activate the Audio setting menu, proceed as follows:
RCU
• Press the ADJ key to activate the OSD
• Use the cursor keys to navigate to the
Audio setting menu
• The icon will turn blue, and the setting dialog will pop up
Icon Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to the
Audio setting menu
• The icon will turn blue, and the setting dialog will pop up
5-32 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.5.1 Volume
Volume can be adjusted in the range from 0 to 79.
Use the push button 3 on the right rear side of the monitor to directly increase the volume, use the push button 4 to directly decrease the volume.
RCU
• Use the up and down cursor keys to navigate to the Volume
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Volume
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
5.5.2 Balance
Balance can be adjusted in the range from -15 to +15.
The zero position is in the center of the slider. In case the left and the right speaker are not balanced, i.e. one side is predominant, adjust the setting in negative direction to bring out the left speaker, in positive direction to bring out the right speaker.
RCU
• Use the up and down cursor keys to navigate to the Balance
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Balance
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
5.5.3 Bass
Bass can be adjusted in the range from -7 to +7.
The zero position is in the center of the slider. In case the low frequencies are predominant, adjust the slider to the left. In case they are rather faint or missing, adjust the slider to the right, iti i i th t f th lid I
Push button (1: top most)
• Use the up and down cursor keys to navigate to the Bass
• Press 5 and 6 to navigate to Bass
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-33
5. The On Screen Display (OSD)
5.5.4 Treble
Treble can be adjusted in the range from -7 to +7.
The zero position is in the center of the slider. In case the high frequencies are predominant, adjust the slider to the left. In case they are rather faint or missing, adjust the slider to the right.
RCU
• Use the up and down cursor keys to navigate to the Treble
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Treble
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
5-34 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.6 Display parameter setting menu
On the Display parameter setting menu, setting of display address, baud rate, light sensor, lower brightness level, ambient light threshold & auto source selection can be done.
To activate the Display parameter setting menu, proceed as follows:
RCU
• Press the ADJ key to activate the OSD
• Use the cursor keys to navigate to the
Display parameter setting menu
• The icon will turn blue, and the setting dialog will pop up
Icon Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to the
Display parameter setting menu
• The icon will turn blue, and the setting dialog will pop up
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-35
5. The On Screen Display (OSD)
To select a display parameter; proceed as follows:
RCU
• Use the up and down cursor keys to navigate to the desired parameter
• Use the left and right cursor keys to activate the desired value.
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to the desired parameter
• Use 3 and 4 to activate the desired value
The current selection is visualized by a white caption.
5.6.1 Set display address
The value can be set in the range from 1 to 255.
If more than one monitor is installed, the monitors can independently be RS232 remote-controlled by means of their display address.
Default monitor address is "1". Allowed addresses are in the range from 1 to 255.
"
1
" is the common address.
A monitor will listen to the commands explicitly sent to his specific address and to commands sent to the common address.
RCU
• Use the up and down cursor keys to navigate to the Set display address
• Use the left and right cursor keys to increase/decrease the address in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Set display address
• Use 3 and 4 to increase/decrease the address in steps of 1
The current value is indicated.
5.6.2 Baud rate
The value can be set to 115200, 38400, 19200, 9600.
RCU
• Use the up and down cursor keys to navigate to the Baud rates
Push button (1: top most)
• Press 5 and 6 to navigate to Baud rate
• Use the left and right cursor keys to i select one of the options 115200, 38400, 19200, 9600.
The current selection is visualized by a white caption
• Use 3 and 4 to select one of the options 115200,
38400, 19200, 9600.
The current selection is visualized by a white caption
The value is applied without any further action.
5-36 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.6.3 Light Sensor
The light sensor can be set on or off.
When a room is dark, the picture content can be viewed at lower brightness (power saving, avoiding eye fatigue). If enabled, the light sensor measures the ambient light, and if the room gets dark enough, the monitor will be switched to the "dark mode" with a brightness set via the Light Sensor Value.
RCU
• Use the up and down cursor keys to navigate to the Light Sensor
• Use the left and right cursor keys to select one of the options Off, On
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Light Sensor
• Use 3 and 4 to select one of the options Off, On
The current selection is visualized by a white caption.
5.6.4 Lower brightness level
The lower brightness level value can be set in the range from 0 to 100.
This parameter defines the brightness the monitor is automatically switched to when the ambient light is below the threshold of the light sensor (dark mode, requires that the light sensor is set On!)
RCU
• Use the up and down cursor keys to navigate to the Lower brightness level
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Lower brightness
level
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
5.6.5 Ambient light threshold
The ambient light threshold can be set in the range from 0 to 100.
This parameter defines the ambient light level below which the monitor will switch to a low backlight mode.
(dark mode, requires that the light sensor is set On!)
RCU
• Use the up and down cursor keys to navigate to the Ambient light threshold
• Use the left and right cursor keys to increase/decrease the value in steps of 1
The current value is indicated.
The value is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Ambient light
threshold.
• Use 3 and 4 to increase/decrease the value in steps of 1
The current value is indicated.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-37
5. The On Screen Display (OSD)
5.6.6 Auto Source Selection
The Auto Source Selection can be set on or off.
When Auto Source Selection is on, the system searches for a valid input source signal.
RCU
• Use the up and down cursor keys to navigate to
Auto Source Selection
• Use the left and right cursor keys to select one of the options Off, On
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Auto Source Selec-
tion
• Use 3 and 4 to select one of the options Off, On
The current selection is visualized by a white caption.
5-38 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.7 Reset menu
On the Reset menu, the factory settings can be restored. It also shows runtime & serial number of the display.
To activate the Reset menu, proceed as follows:
RCU
• Press the ADJ key to activate the OSD
• Use the cursor keys to navigate to the
Reset menu
• The icon will turn blue, and the setting dialog will pop up
Icon Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to the
Reset menu
• The icon will turn blue, and the setting dialog will pop up
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-39
5. The On Screen Display (OSD)
5.7.1 Factory Reset
Clicking the button Yes on the option Factory Reset will inevitable reset the monitor to its factory settings.
All former adjustment and modifications will be lost!
These are the factory settings which are applied after selecting Yes with Factory Reset:
Item default
Power switch Off
Brightness 80
Contrast
Color temp.
Red
Green
50
User
255
255
Blue
Language
Auto configuration
255
English
On adjust range
On/Off
0~100
0~100
User, 3200K,5400K,6500K, 9300K
0~255
0~255
0~255
English
On/Off
RCU
• Use the up and down cursor keys to navigate to the Factory Reset
• Use the left and right cursor keys to select one of the options Yes, No
The current selection is visualized by a white caption.
The selection is applied without any further action.
Push button (1: top most)
• Press 5 and 6 to navigate to Factory Reset
• Use 3 and 4 to select one of the options Yes, No
The current selection is visualized by a white caption.
5-40 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
5. The On Screen Display (OSD)
5.8 Input Signal Selection
In case multiple sources are connected, the signal for the first input and the second input have to be defined.
To select the signal for the respective input, proceed as follows:
RCU
• Press the ADJ key to activate the OSD
• Use the left and right cursor keys to navigate to the signal menu (for the first input)
• Press Enter to select
Icon Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to the
signal (for the first menu input)
• Press 2 to select
• Use the down cursor keys to open the input signal selection dialog
• Press 4 to open the input signal selection dialog
After the source has been selected, its timing is displayed.
In case the timing of the source is not included in the presets of the monitor, the timing of the monitor which matches best the timing of the source is displayed!
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-41
5. The On Screen Display (OSD)
The following sources can be connected to the monitor:
Input
Video system input
RGB input
HD-SDI input
VIDEO IN
RGB Analog
RGB Digital
Serial Digital
Interface
RCA
S-VIDEO S-Video Mini Din 4pin NTSC/PAL
YUV (Y Pb/Cb Pr/Cr) Component Mini Din 8 pin NTSC/PAL
D-Sub 15 pin
DVI-D 24 pin
BNC signals
NTSC/PAL
RGB analog
RGB digital
SDI / HDSDI
To select a signal, proceed as follows:
RCU
• Press the ADJ key to activate the OSD
• Use the left and right cursor keys to navigate to the signal menu
• Press Enter to select
Icon Push button (1: top most)
• Press 7 to activate the OSD
• Press 3 and 4 to navigate to the
signal menu
• Press 2 to select
• Use the down cursor keys to open the input signal selection dialog
• Use the left and right cursor keys to select the desired signal
• Press 4 to open the input signal selection dialog
• Press 3 and 4 to select the desired signal
In case the signal is assigned to input 1, it cannot be assigned to input 2!
To change the signal of input 1 and input 2, input 1 has to be assigned to the signal which up to then has been assigned to input 2.
In case of two valid signals, input 2 then will automatically be assigned to the signal which up to then has been assigned to input 1.
In case of more signals, input 2 has to be explicitely assigned to a signal (all but the one assigned to input 1).
To select HD-SDI input 1 or HD-SDI input 2, first select HD-SDI in the OSD. When it is highlighted, press 1 to select the signal connected to HD-SDI input 1, or press 2 to select the signal connected to HD-SDI input 2.
5-42 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
In case no signal is applied, the monitor displays a "no sync" message.
5. The On Screen Display (OSD)
In case no cable is connected, the monitor displays a "no cable" message.
In case the timing of the connected source is not compliant to the monitor, the monitor displays a "invalid mode" message.
For a list of compliant timings, cf. chapter 9 Compliant timing
The monitor features autodetect. In case e.g. DVI is selected, but the only connected source is VGA, the monitor will display the no sync message, and after a while automatically switch to VGA.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
5-43
5. The On Screen Display (OSD)
If no source is connected (neither no sync, no cable, no valid signal), the monitor switches to standby and displays the respective information:
Whenever one of these messages pop up, check the respective item and fix it!
5.8.1 Input selection with the function key F1
For input 1, the input can be selected using the function key F1. Pressing F1 "scrolls" through the inputs and displays one after the other the respective icon.
Press Enter to directly select the desired input.
5-44 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
6. Maintenance and servicing
6 Maintenance and servicing
Only authorized personnel should carry out other maintenance work not explicitly mentioned in this manual!
Never open the case of the monitor without first disconnecting the power supply cord!
Measurements and tests with the opened device may be carried out only in the factory or by specially trained personnel, due to the dangers of electrical shock.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
6-1
6. Maintenance and servicing
6.1 Cleaning
Consult your dealer for internal cleaning once a year.
If you allow dust to accumulate on the unit, it may cause fire or malfunction when you operate it.
Refer to your dealer about the internal cleaning.
Power plug
If dust has collected on the power plug connectors, remove the plug from the outlet and clean off the dust. This dust may cause a fire due to reduced insulation of the plug.
Cabinet
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. To keep the cabinet looking brand-new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution. Never use strong solvents, such as thinner or benzene, or abrasive cleaners, since these will damage the cabinet.
Contamination of screen surface.
When the screen surface of the monitor is contaminated, please wipe the surface softly with cotton swab or clean cloth. If it is not enough, please take it away with cellophane tape or wipe the surface with cotton swab or clean cloth containing solvent of 50% alcohol. In this case, please be careful so that the solvent does not get in inside of the LCD module, because it may be damaged.
Water drop on LCD surface
Please do not leave LCD module with water drop. When the display surface gets water drop, please wipe it off with cotton swab or soft cloth immediately, otherwise display surface will be deteriorated. If water gets in inside the LCD module, the electric circuits may be damaged.
6-2 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
7. Technical data 42" version (LCN-42, LCS-42)
7 Technical data 42" version (LCN-42, LCS-42)
7.1 General data
characteristic
Screen size
Aspect ratio active area (HxW) width x height x depth
(without stand!) weight specification
42” diagonal
16:9
934mm x 527mm | 36.77in. x 20.75in.
1026mm x 619mm x 123.7mm | 40.39in. x 24.37in. x 4.87in.
29.5kg | 65.1lbs
Table 7-1
7.2 LCD panel
characteristic
Driver element
Pixel number
Display colors
Viewing angle
Brightness
Contrast ratio
Response time (Gray to Gray)
Interfaces
Dead pixel rate specification a-Si TFT active matrix
(1920 x R.G.B. x 1080) pixel (HDTV)
16.8 millions of colors
176 degree vertical / 176 degree horizontal
500 cd/m²
1800:1
Typ. 6.5 msec, max. 12msec
VGA (D-Sub 15 pins), DVI (DVI-D 24 pins), Composite (RCA), S-Video
(Mini-DIN 4 pin), Component (Mini-DIN 8 pin), SDI/HD-SDI in/out (BNC),
RS232 IN/OUT (D-Sub 9)
Max. 8 bright pixels out of which max. 2 clusters of two bright pixels.
Max.10 dark pixels out of which max. 5 clusters of two dark pixels
Table 7-2
7.3 Electrical data
Characteristic
Power supply specification
100VAC-240 VAC, 50/60 Hz
Power consumption operating mode 234W | 116 BTU/h
Power consumption Standby mode 14.8W | 50.5 BTU/h
Table 7-3
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
7-1
7. Technical data 42" version (LCN-42, LCS-42)
7.4 Operating conditions
Characteristic
Storage temperature
Operating ambient temperature specification
-20°C - +60°C | -4°F – 140°F, at max. 90% RH, non-condensing
+5°C – +40°C | 41°F – 104°F, at max. 90% RH, non-condensing
Table 7-4
7.5 CCFL (Cold Cathode Fluorescent Lamp) characteristics (ambient temperature (25 ±2)°C)
Characteristic
Lamp voltage
Lamp current
Lamp starting voltage
Lamp life time
Operating frequency
Typ. value
1520 VRMS
5.8 mARMS
2370 VRMS (0°C), 2160 VRMS (25°C)
50,000hrs *)
40-70 KHz
Table 7-5
The life time of a lamp is defined as when the brightness is larger than 50% of its original value and the effective discharge length is longer than 80% of its original length.
7.6 Interfaces
7.6.1 Video IN (Composite Video)
Item
Signal level
Connector type
Termination specification
1.0Vpp
RCA Jack
75 Ω
Table 7-6
7-2 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
7. Technical data 42" version (LCN-42, LCS-42)
7.6.2 S-Video
Item
1,2
3
4
Luminance level
Color level
Connector type
Termination specification
Ground
Y
C
1.0 Vpp
0.286 Vpp
Mini Din 4pin
75 Ω
2
4 3
1
7.6.3 Component Video (mini DIN 8 pin)
2
3
4
Item
1
Connector type
Termination specification
GND
CB
GND
Y
5
8 7
2
4
1
3
6
6
7
8
Item
5
Mini Din 8pin
75 Ω specification
GND
CR not connected not connected
Table 7-7
Table 7-8
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
7-3
7. Technical data 42" version (LCN-42, LCS-42)
Y
Pb
Pr
IRE mV
IRE mV
IRE mV
White
75
525
0
0
0
0
Yellow
69.5
487
-37.5
-263
3.4
24
Cyan
59.1
413
8.6
60
-37.5
-263
Green Magenta
53.6 21.4
375
-28.9
-202
-34.1
-238
150
28.9
202
34.1
238
HDTV YPbPr 75% color bars. Values are relative to the blanking level.
White Yellow Cyan Green Magenta
IRE 100 92.8 78.7 71.5 28.5
Y mV
IRE
700
0
649
-50
551
11.5
501
-38.5
199
38.5
Pb mV
IRE
0
0
-350
4.6
80
-50
-270
-45.4
270
45.4
Pr mV 0 32 -350 -318 318
Red
21.3
149
-11.5
-80
50
350
Red
15.9
112
-8.6
-60
37.5
263
HDTV YPbPr 100% color bars. Values are relative to the blanking level.
White Yellow Cyan Green Magenta
IRE 75 66.5 52.6 44.0 31.0
Y mV
IRE
525
0
465
-37.5
368
12.7
308
-24.8
217
24.8
Cb mV
IRE
0
0
-263
6.1
89
-37.5
-174
-31.4
174
31.4
Cr mV 0 43 -263 -220 220
Red
22.4
157
-12.7
-89
37.5
263
SDTV YCbCr 75% color bars. Values are relative to the blanking level.
Blue
5.4
38
37.5
263
-3.4
-24
Black
0
0
0
0
0
0
Table 7-9
Blue
7.2
51
50
350
-4.6
-32
Black
0
0
0
0
0
0
Table 7-10
Blue
8.6
60
37.5
263
-6.1
-43
Black
0
0
0
0
0
0
Table 7-11
7-4 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
7. Technical data 42" version (LCN-42, LCS-42)
Y
Cb
Cr
IRE mV
IRE mV
IRE mV
White
100
700
0
0
0
0
Yellow
88.6
620
-50
-350
8.1
57
Cyan
70.1
491
16.9
118
-50
-350
Green Magenta
58.7 41.3
411
-33.1
289
33.1
-232
-41.9
-293
232
41.9
293
Red
29.9
209
-16.9
-118
50
350
SDTV YCbCr 100% color bars. Values are relative to the blanking level.
7.6.4 SDI/HDSDI IN/OUT (BNC) (LCS-42 only)
Blue
11.4
80
50
350
-8.1
-57
Black
0
0
0
0
0
0
Table 7-12
1
2
1 Signal, typ. 0.8Vpp
2 Shield
SDI/HDSDI
IN
BNC input, 75 Ω terminated
SDI/HDSDI
Out
BNC output, output impedance 75 Ω. Loop through of the active HDSDI input.
Table 7-13
7.6.5 DVI
7
8
9
10
11
12
4
5
6
Pin
1
2
3 signal assignment
TMDS Data 2-
TMDS Data 2+
TMDS Data 2 Ground
NC
NC
DDC Clock
DDC Data
NC
TMDS Data 1-
TMDS Data 1+
TMDS Data 1 Ground
NC
1
9
17
8
16
24 pin
13
14
15
16
17
18
19
20
21
22
23
24 signal assignment
NC
NC
Ground (+5, Analog /V Sync)
Hot Plug Detect (HPD)
TMDS Data 0-
TMDS Data 0+
TMDS Data 0 Ground
NC
NC
TMDS Clock Ground
TMDS Clock +
TMDS Clock -
Table 7-14
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
7-5
6
7
8
3
4
5
Pin
1
2
6
7
4
5
8
2
3
Pin
1
7. Technical data 42" version (LCN-42, LCS-42)
7.6.6 RGB IN (D-Sub 15 pin)
5
10
15 signal assignment
Red video input
Green video input
Blue video input
NC
Ground
Red video ground
Green video ground
Blue video ground
7.6.7 RS232 IN
1
6
NC
NC
NC signal assignment
NC
Signal receive
Signal transmit
NC
Ground
1
6
11
12
13
14
15 pin
9
10
11 signal assignment
NC
Ground
NC
(SDA)
Horizontal sync (Composite sync)
Vertical sync
(SCL)
Table 7-15
9
5
Table 7-16
7-6 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
7. Technical data 42" version (LCN-42, LCS-42)
7.6.8 RS232 OUT
1
6 9
5
6
7
8
3
4
5
Pin
1
2
7.7 Factory settings
Item default
Power switch Off
Brightness 80
Contrast
Color temp.
Red
Green
Blue
Language
Baud rate
Auto configuration
50
User
255
255
255
English
115200
On
NC
NC
NC signal assignment
NC
Signal transmit
Signal receive
NC
Ground adjust range
On/Off
0~100
0~100
User, 3200K,5400K,6500K, 9300K
0~255
0~255
0~255
English
115200, 38400, 19200, 9600
On/Off
Table 7-17
Table 7-18
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
7-7
8. Technical data 47" version (LCN-47, LCS-47)
8 Technical data 47" version (LCN-47, LCS-47)
8.1 General data
characteristic
Screen size
Aspect ratio active area (HxW) width x height x depth
(without stand, with handle!) weight specification
47” diagonal
16:9
1048mm x 593mm | 41.26in. x 23.35in.
1139.4mm x 684.4mm x 125mm | 44.86in x 26.94in X 4.92in
40.2kg | 88.7lbs
Table 8-1
8.2 LCD panel
characteristic
Driver element
Pixel number
Display colors
Viewing angle
Brightness
Contrast ratio
Response time (Gray to Gray)
Interfaces
Dead pixel rate specification a-Si TFT active matrix
(1920 x R.G.B. x 1080) pixel (HDTV)
16.8 millions of colors
176 degree vertical / 176 degree horizontal
500 cd/m²
1800:1
Typ. 6.5 msec, max. 12 msec.
VGA (D-Sub 15 pins), DVI (DVI-D 24 pins), Composite (RCA), S-Video
(Mini-DIN 4 pin), Component (Mini-DIN 8 pin), SDI/HD-SDI in/out (BNC),
RS232 IN/OUT (D-Sub 9)
Max. 8 bright pixels out of which max. 2 clusters of two bright pixels.
Max. 10 dark pixels out of which max. 5 clusters of two dark pixels
Table 8-2
8.3 Electrical data
Characteristic
Power supply specification
100VAC-240 VAC, 50/60 Hz
Power consumption operating mode 303W | 1033.8 BTU/h
Power consumption Standby mode 19.9W | 67.9 BTU/h
Table 8-3
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
8-1
8. Technical data 47" version (LCN-47, LCS-47)
8.4 Operating conditions
Characteristic
Storage temperature
Operating ambient temperature specification
-20°C - +60°C | -4°F – 140°F, at max. 90% RH, non-condensing
+5°C – +40°C | 41°F – 104°F, at max. 90% RH, non-condensing
Table 8-4
8.5 CCFL (Cold Cathode Fluorescent Lamp) characteristics (ambient temperature (25 ±2)°C)
Characteristic
Lamp voltage
Lamp current
Lamp starting voltage
Lamp life time
Operating frequency
Typ. value
1750 VRMS
6 mARMS
2350 VRMS (0°C), 2150 VRMS (25°C)
50,000hrs *)
40-70 KHz
Table 8-5
The life time of a lamp is defined as when the brightness is larger than 50% of its original value and the effective discharge length is longer than 80% of its original length.
8.6 Interfaces
8.6.1 Video IN (Composite Video)
Item
Signal level
Connector type
Termination specification
1.0Vpp
RCA Jack
75 Ω
Table 8-6
8-2 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
8. Technical data 47" version (LCN-47, LCS-47)
8.6.2 S-Video
Item
1,2
3
4
Luminance level
Color level
Connector type
Termination specification
Ground
Y
C
1.0 Vpp
0.286 Vpp
Mini Din 4pin
75 Ω
2
4 3
1
Table 8-7
8.6.3 Component Video
Item
1
2
3
4
Connector type
Termination specification
GND
CB
GND
Y
5
8 7
2
4
1
3
6
6
7
Item
5
8
Mini Din 8pin
75 Ω specification
GND
CR not connected not connected
Y
Pb
Pr
IRE mV
IRE mV
IRE mV
White
75
525
0
0
0
0
Yellow
69.5
487
-37.5
-263
3.4
24
Cyan
59.1
413
8.6
60
-37.5
-263
Green Magenta
53.6
375
-28.9
-202
-34.1
-238
HDTV YPbPr 75% color bars. Values are relative to the blanking level.
21.4
150
28.9
202
34.1
238
Red
15.9
112
-8.6
-60
37.5
263
Blue
5.4
38
37.5
263
-3.4
-24
Table 8-8
Black
0
0
0
0
0
0
Table 8-9
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
8-3
8. Technical data 47" version (LCN-47, LCS-47)
Y
Pb
Pr
IRE mV
IRE mV
IRE mV
White
100
700
0
0
0
0
Yellow
92.8
649
-50
-350
4.6
32
Cyan
78.7
551
11.5
80
-50
-350
Green Magenta
71.5 28.5
501
-38.5
199
38.5
-270
-45.4
-318
270
45.4
318
Red
21.3
149
-11.5
-80
50
350
HDTV YPbPr 100% color bars. Values are relative to the blanking level.
White Yellow Cyan Green Magenta
IRE 75 66.5 52.6 44.0 31.0
Y mV
IRE
525
0
465
-37.5
368
12.7
308
-24.8
217
24.8
Cb mV
IRE
0
0
-263
6.1
89
-37.5
-174
-31.4
174
31.4
Cr mV 0 43 -263 -220 220
Red
22.4
157
-12.7
-89
37.5
263
SDTV YCbCr 75% color bars. Values are relative to the blanking level.
White Yellow Cyan Green Magenta
IRE 100 88.6 70.1 58.7 41.3
Y mV
IRE
700
0
620
-50
491
16.9
411
-33.1
289
33.1
Cb mV
IRE
0
0
-350
8.1
118
-50
-232
-41.9
232
41.9
Cr mV 0 57 -350 -293 293
Red
29.9
209
-16.9
-118
50
350
SDTV YCbCr 100% color bars. Values are relative to the blanking level.
Blue
7.2
51
50
350
-4.6
-32
Black
0
0
0
0
0
0
Table 8-10
Blue
8.6
60
37.5
263
-6.1
-43
Black
0
0
0
0
0
0
Table 8-11
Blue
11.4
80
50
350
-8.1
-57
Black
0
0
0
0
0
0
Table 8-12
8-4 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
8. Technical data 47" version (LCN-47, LCS-47)
8.6.4 SDI/HDSDI IN/OUT (BNC)
5
6
7
Pin
1
2
3
4
8
9
10
11
12
1
2
1 Signal, typ. 0.8Vpp
2 Shield
SDI/HDSDI
IN
BNC input, 75 Ω terminated
SDI/HDSDI
Out
BNC output, output impedance 75 Ω. Loop through of the active HDSDI input.
8.6.5 DVI
1
9
17 signal assignment
TMDS Data 2-
TMDS Data 2+
TMDS Data 2 Ground
NC
NC
DDC Clock
DDC Data
NC
TMDS Data 1-
TMDS Data 1+
TMDS Data 1 Ground
NC
8
16
24 pin
13
14
15
16
17
18
19
20
21
22
23
24
Table 8-13 signal assignment
NC
NC
Ground (+5, Analog /V Sync)
Hot Plug Detect (HPD)
TMDS Data 0-
TMDS Data 0+
TMDS Data 0 Ground
NC
NC
TMDS Clock Ground
TMDS Clock +
TMDS Clock -
Table 8-14
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
8-5
6
7
8
3
4
5
Pin
1
2
6
7
4
5
8
2
3
Pin
1
8. Technical data 47" version (LCN-47, LCS-47)
8.6.6 RGB IN (D-Sub 15 pin)
5
10
15 signal assignment
Red video input
Green video input
Blue video input
NC
Ground
Red video ground
Green video ground
Blue video ground
8.6.7 RS232 IN
1
6
NC
NC
NC signal assignment
NC
Signal receive
Signal transmit
NC
Ground
12
13
14
15 pin
9
10
11
1
6
11 signal assignment
NC
Ground
NC
(SDA)
Horizontal sync (Composite sync)
Vertical sync
(SCL)
Table 8-15
9
5
Table 8-16
8-6 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
8. Technical data 47" version (LCN-47, LCS-47)
8.6.8 RS232 OUT
6
7
8
3
4
5
Pin
1
2
NC
NC
NC signal assignment
NC
Signal transmit
Signal receive
NC
Ground
1
6 9
5
Table 8-17
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
8-7
8. Technical data 47" version (LCN-47, LCS-47)
8.7 Factory setting
Item default
Power switch Off
Brightness
Contrast
80
50
Color temp.
Red
Green
Blue
User
255
255
255
Language
Baud rate
Auto configuration
English
115200
On adjust range
On/Off
0~100
0~100
User, 3200K,5400K,6500K, 9300K
0~255
0~255
0~255
English
115200, 38400, 19200, 9600
On/Off
Table 8-18
8-8 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
9. Compliant timing
9 Compliant timing
< Horizontal >
Video
Sync
B C
A
<Vertical >
Graphics Mode
H-parameters
A: Total period
B: Sync. width
C: Back porch
D: Active video
E: Front porch
Sync polarity
P Q
Horizontal (dot)
O
R
H V A B C D E
S
V-parameters
O: Total period
P: Sync. width
Q: Back porch
R: Active video
S: Front porch
Vertical (line)
O P Q R S
37.861 72.809 31.500 N N 832 40 120 640 32 520 3 20 480 17 OK OK
VGA
640x480
SVGA
800x600
XGA
1024x768
37.500 75.000 31.500 N N 840 64 120 640 16 500 3 16 480 1 OK OK
43.269 85.010 36.000 N N 832 56 80 640 56 509 3 25 480 1 OK OK
35.156 56.250 36.000 P P 1024 72 128 800 24 625 2 22 600 1 OK OK
37.879 60.317 40.000 P P 1056 128 88 800 40 628 4 23 600 1 OK OK
48.077 72.188 50.000 P P 1040 120 64 800 56 666 6 23 600 37 OK OK
46.875 75.000 49.500 P P 1056 80 160 800 16 625 3 21 600 1 OK OK
53.674 85.06 56.250 P P 1048 64 152 800 32 631 3 27 600 1 OK OK
48.363 60.004 65.000 N N 1344 136 160 1024 24 806 6 29 768 3 OK OK
56.476 70.069 75.000 N N 1328 136 144 1024 24 806 6 29 768 3 OK OK
60.023 75.029 78.750 P P 1312 96 176 1024 16 800 3 28 768 1 OK OK
VESA
68.677 85.00 94.500 N N 1376 96 208 1024 48 808 3 36 768 1 OK OK
WXGA
1360x768
SXGA
1152x864
47.712
67.500
59.94
75.000
84.737
108.000
N
P
N
P
1776 152 176 1360
1600 128 256 1152
88
64
796
900
3
3
24
32
768
864
1
1
OK OK
OK OK
SXGA
1280x960
60.000 60.00 108.000
N N 1800 112 312 1280 96 1000 3 36 960 1 OK OK
85.938 85.00 148.501
N N 1728 160 224 1280 64 1011 3 47 960 1 OK OK
63.981 60.020 108.000
P P 1688 112 248 1280 48 1066 3 38 1024 1 OK OK
SXGA
1280x1024
79.976 75.025 135.000
P P 1688 144 248 1280 16 1066 3 38 1024 1 OK OK
91.146 85.02 157.500
P P 1728 160 224 1280 64 1072 3 44 1024 1 OK OK
SXGA+
1400x1050
65.316 59.978 121.749
N N 1864 144 232 1400 88 1089 4 32 1050 3 OK OK
82.278 74.866 156.000
N N 1896 144 248 1400 104 1099 4 42 1050 3 OK OK
UXGA
1600x1200
75.00 60.00 162.000
N N 2160 192 304 1600 64 1250 3 46 1200 1 OK OK
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
9-1
9. Compliant timing
Video Mode
Sync polarity
H V A
Horizontal (dot)
D E
Vertical (line)
O P Q R S
SMPTE
296M
HDTV
SMPTE
274M
HDTV
37.500 50 74.25 N N 1980 40 220 1280 440 750 5 20 720 5 OK OK
720p
1280x780
45.000 60 74.250 P P 1650 40 220 1280 110 750 5 20 720 5 OK OK
44.995 59.94 74.176 P P 1650 40 220 1280 110 750 5 20 720 5 OK OK
56.250 50.00 148.500
P P 2640 44 148 1920 528 1125 5 36 1080 4 OK OK
1080p
1920x1080
67.433 59.94 148.352
P P 2200 44 148 1920 88 1125 5 36 1080 4 OK OK
67.500 60.00 148.500
P P 2200 44 148 1920 88 1125 5 36 1080 4 OK OK
28.13 50.00 74.25 P P 2640 44 148 1920 528 1125 5 38 1080 4 OK OK
1080i
1920x1080
33.716 59.94 74.176 P P 2200 44 148 1920 88 1125 5 38 1080 4 OK OK
33.750 60 74.25 P P 2200 44 148 1920 88 1125 5 38 1080 4 OK OK
NTSC
PAL
NTSC 358-443 15.734
PAL SECAM 15.625
59.94
50.00
16.521
16.406
Composite, S-video and component video inputs accept only standard 480i NTSC and 576i PAL-SECAM video.
DVI and VGA inputs accepts progressive 480p and 576p video.
9.1 SDI input signals
The Serial Digital Interface (SDI) input complies with the standard SMPTE 259M.
The input board accepts the following SDI input formats and types (table 1):
Resolution Signal type
720x480
720x576
NTSC
PAL
9-2 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
9. Compliant timing
9.2 HD-SDI input signals
The HD-SDI input complies with the standard SMPTE 292M.
The HD-SDI input supports the following resolutions (table 2).
1280x720
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1650
1650
1980
2200
2200
2640
2200
2200
2640
750
750
750
1125
1125
1125
1125
1125
1125
1280
1280
1280
1920
1920
1920
1920
1920
1920
720
720
720
1080
1080
1080
1080
1080
1080
1:1 p
1:1 p
1:1 p
2:1 i
2:1 i
2:1 i
1:1 prog
1:1 prog
1:1 prog
60
60/
M
50
30
30/
M
25
30
30/
M
25
1920x1080 2750 1125 1920 1080 1:1 prog 24
HD-SDI-Resolutions (M=1.001, p=progressive, i=interlaced) at data rate 1.485 or 1.485/1.001 Gb/s.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
9-3
10 Troubleshooting
When faults occur which are not described below please contact Barco.
10. Troubleshooting
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
10-1
10. Troubleshooting
10.1 Faults
Faults
No picture
The monitor can not be controlled via the
IR RCU
The picture color is pale, or not clear cause/steps
Make sure that the power cord is plugged into the wall outlet.
Make sure that the power switch on the rear of the monitor is switched on!
Make sure that the monitor is not in standby (check the LED indicator: if it shows orange, the monitor is in standby)
Check if the signal cables are properly connected to the monitor and to the signal source
Check if the input setting is correct (VGA, DVI, Composite, S-
Video, Component, HD-SDI)
Check if the signal is suitable.
Make sure that the batteries are inserted correctly (matching the + and – marks of the battery compartment)
Replace the batteries.
Point the front of the RCU directly to the sensor on the screen.
The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control unit and the IR sensor.
Check the Color setting
If you are using YUV terminals, make sure that the cables are correctly connected!
Press F4 on the remote control. The picture is green or purple when VGA signal is connected
Picture vibrates when genlock is selected on the Barco Transform H/A controller
Picture vibrates when interlaced video signal is brought to the DVI or VGA input.
The monitor doesn’t work with the analog output of the Barco Transform H/A controllers
PC/graphical card doesn’t work on the VGA input
The monitor says ‘no signal’ or ‘no cable’ when a DVI or VGA signal is attached.
The VGA image is not scaled properly.
Restart the monitor to let it resync.
Restart the monitor to let it resync.
It is not supposed to. Use the digital output and DVI input to the monitor.
Use the digital output (DVI) of your graphical card or docking station.
This may happen if a video input is used before switching off. Keep pressing F1 on the remote control until the right input is selected. If this doesn’t help, check the table of timings to make sure the input signal is supported.
Press the || button on the remote control to autoadjust.
Table 10-1
10-2 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
10.2 Contact
Feel free to contact us if you have any further questions!
• Barco Control Rooms GmbH
An der Rossweid 5 • D-76229 Karlsruhe • Germany
Phone (49) (721) 6201-163 • Fax (49) (721) 6201-298
E-mail [email protected]
, Web www.barcocontrolrooms.de
• BARCO N.V.
President Kennedypark 35 • B-8500 Kortrijk • Belgium
Phone (32) (56) 36-8282 • Fax (32) (56) 36-82 51
E-mail [email protected]
,• Web www.barcocontrolrooms.com
• BARCO N.V. Media
Noordlaan 5 • B-8520 Kuurne • Belgium
Phone (32) (56) 36-8970 • Fa× (32) (56) 36-8386
E-mail [email protected]
,• Web www.barco.com
10. Troubleshooting
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
10-3
11. Compliance statement
11 Compliance statement
11.1 FCC Compliance statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
11-1
12. Accessories
12 Accessories
The monitor can be equipped with a table stand, or mounted to the wall or the ceiling. The following chapter describes assembling and installation of the accessories.
12.1 Required tools
• Screwdriver for recessed head screws (screw size M8)
Wall mount and ceiling mount:
• Wrench 10mm, 17mm, 19mm
• Allen wrench size 2.5 to adjust the tilt angle of the long/short ceiling mount
• Drilling machine to drill the holes into concrete
• 4 fixation screws per wall mount / ceiling mount
• 1 additional (center) fixation screw for the tiltable wall mount
• 4 (5) dowels (concrete)
The manufacturer of the accessories gives the following recommendation:
Specification of screws for wood: DIN 571 M8x80 4.6
Specification of screws for concrete DIN 16168 M8x75
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
12-1
12. Accessories
12.2 Table stand
The table stand allows adjusting the monitor in height.
For the 42" version, the lower edge can be set between 14mm and 204mm; for the 47" versions, the lower edge can be set between 14mm and 135mm.
12.2.1 Scope of delivery
The table stand comes fully assembled.
12-2 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.2.2 Installation
The monitors feature on their rear side 2 parallel arrangements of 4 threads each. These threads comply with the
VESA standards, their horizontal and vertical distance is 200mm. They are equipped with the respective screws
(M8x15).
These screws are used to attach the table stand!
• Lay the monitor upside down on a clean(!) surface, bottom edge flush with e.g. edge of the table.
Soil or particles laying on the surface may irretrievably damage the screen of the monitor!
• Take a screwdriver for recessed head screws (screw size M8).
• Remove the 4 center screws and washers on the rear side of the monitor.
• Take the table stand and attach its mounting plate to the rear of the monitor using the previously removed screws and washers.
Mind the correct orientation of the table stand!
• When the screws are fastened tightly, put up the monitor
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
12-3
12. Accessories
12.2.3 Dimensions
12.2.3.1 Dimensions of the 42" version
12.2.3.2 Dimension of the 47" version
12-4 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.2.4 Height adjustment
The monitor can be adjusted in height by sliding the mounting plate up or down, respectively.
For adjusting the table stand in height, first uninstall the monitor!!
Never loosen the screws for sliding the plate when the monitor is still attached to the table stand! Otherwise the monitor will crash on the table!!
• Uninstall the monitor!
• Remove the 2 fixation screws of the plate to the vertical bar at each side.
• Re-position the monitor.
• Re-attach the screws.
• Install the table stand to the monitor.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
12-5
12. Accessories
12.3 Screen bracket (adapter plate)
The installation of the screen bracket is mandatory for fixation of the wall mount, and the ceiling mount..
12.3.1 Scope of delivery
The screen bracket is one component; for its installation the screws on the rear side of the monitor are used.
12-6 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.3.2 Installation
The monitors feature on their rear side 2 parallel arrangements of 4 threads each. The threads comply with the
screws (M8x15).
These screws are used to attach the screen bracket!
To install the screen bracket, proceed as follows:
• Lay the monitor upside down on a clean(!) surface.
• Take a screwdriver for recessed head screws (screw size M8).
• Remove the 8 screws and washers on the rear side of the monitor.
• Take the screen bracket, and fix it with the 8 screws and washers as shown below.
The screen bracket is equipped with 3 knurled bolts which are later slid into the fixation plate of the wall mount / ceiling mount. These bolts are arranged in a triangle. Make sure that the screen bracket is fixed with the top of the triangle showing to the bottom of the monitor!
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
12-7
12. Accessories
12.4 Fixed wall mount
First mount the screen bracket to the monitor, cf.
. Screen bracket (adapter plate)
Use the fixed wall mount to attach the monitor to the wall.
The drawings show the fixation facility itself and a monitor which is equipped with a fixed wall mount.
12.4.1 Scope of delivery
The fixed wall mount comes in one piece. The 4 screws to attach it to the wall have to be provided on site!
12-8 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.4.2 Installation
The wall mount bracket is attached to the wall by means of 4 screws M8 (for specification of the screws, cf.
Required tools .). It is the same bracket for 42" and 47".
For drilling the holes in the wall, it is recommended to use a jig – take a sheet of paper
(A3) and copy the distances given in the drawing below.
• Drill 4 holes, 10mm, to the wall in the given distances!
• Use 4 screws M8 and fix the wall mount to the wall.
• Slid in the knurled bolts of the screen bracket into the keyholes of the wall mount and lock them by turning the lock bar.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
12-9
12. Accessories
12.4.3 Dimensions
The following pictures give an overview about the measurements and dimensions of the 42" version and the
47".
12.4.3.1 Dimensions of the 42" version:
12.4.3.2 Dimension of the 47" version:
12-10 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.4.4 Wall pattern
In case of a "monitor wall", the arrangement of the holes in the wall can be taken from the following pictures:
12.4.4.2 Wall pattern 47"
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-11
12. Accessories
12.5 Tiltable wall mount
First mount the screen bracket to the monitor, cf.
. Screen bracket (adapter plate)
The tiltable wall mount fixes the monitor to the wall and allows setting its position in 5 steps between zero and
20 degrees. The drawings show the tiltable wall mount at max. and min. tilt angle.
12.5.1 Scope of delivery
The tiltable wall mount comes fully assembled. It comprises a front plate and a rear plate. The rear plate will be attached to the wall, the front plate to the screen bracket of the monitor. The angle between the rear plate and the front plate can be set in 5 steps from zero to 20 degrees (angle between wall and monitor display).
12-12 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.5.2 Installation
The rear plate of the tiltable wall mount bracket is attached to the wall by means of 5 screws M8 (for specification of the screws, cf. Required tools .). It is the same bracket for 42" and 47".
For drilling the holes in the wall, it is recommended to use a jig – take a sheet of paper
(A3) and copy the distances given in the drawing below.
• Drill 5 holes, 10mm, to the wall in the given distances!
• Slid in the knurled bolts of the screen bracket into the keyholes of the wall mount and lock them by turning the lock bar.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-13
12. Accessories
12.5.3 Dimensions
The following pictures give an overview about the measurements and dimensions of the 42" version and the
47".
12.5.3.1 Dimensions of the 42" version:
12.5.3.2 Dimensions of the 47" version:
12-14 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.5.4 Tilting
To tilt the monitor, the two top screws connecting the rear plate and the front plate have to be removed.
If you want to change the tilt angle of the monitor, first uninstall the monitor!!
Never loosen the screws for setting the tilt angle when the monitor is still attached to the tiltable wall mount!
• Uninstall the monitor!
• Use the included allen wrench 4mm to loosen the left and the right top screws.
• Tilt the front plate to the desired degree.
• Reattach the screws.
• Re-install the monitor.
For security reasons, the two top screws to adjust the tilting angle are applied with a center pin and thus require a special tool. Therefore the allen wrench 4mm is included which feature a center hole for the pin.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-15
12. Accessories
12.6 Short ceiling mount
First mount the screen bracket to the monitor, cf.
. Screen bracket (adapter plate)
The short ceiling mount fixes the monitor to the ceiling and allows setting the lower screen edge to a distance of the ceiling between 706.5mm and 885.5mm for the 42" versions, and between 776mm and 955mm for the 47" versions, respectively.
The monitors can be tilted by 20 degrees thanks to the ball point on the ceiling fixation plate.
The drawings show the fixation facility itself and a monitor equipped with the short ceiling mount.
12-16 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.6.1 Scope of delivery
The short ceiling mount comprises 3 parts:
• The base plate with the ball point connection to the adjustable bar. This base plate will be mounted on the ceiling.
• The adjustable bar.
• The adapter plate to attach to the screen bracket of the monitor with two hooks to look the knurled bolts.
The screws to assemble the short ceiling bar are included. You will need a wrench 17mm.
The screws to fix the base plate to the ceiling have to be provided on site, cf. Required tools .
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-17
12. Accessories
12.6.2 Installation
The short ceiling mount is attached to the ceiling by means of 4 screws M8 (for specification of the screws, cf.
Required tools .). It is the same bracket for 42" and 47".
For drilling the holes in the ceiling, it is recommended to use a jig – take a sheet of paper
(A4) and copy the distances given in the drawing below.
• Drill 4 holes, 10mm, to the ceiling in the given distances!
• Attach the ceiling mounting plate.
• Attach the adjustable bar to the ball joint of the ceiling mounting plate by using one of the included screws
M10x60. Secure the screw with the nut and attach the black plastic cap. Also attach a black plastic cap to the already installed parallel screw on the ceiling mounting plate.
• Slide in the adjustable bar into the monitor mounting plate of the short ceiling mount. Fix its position by one of the included screws M10x60. Secure the screw with the nut and attach the black plastic cap.
12-18 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
• The knurled bolts of the screen bracket are slid into the keyholes of the wall mount and locked by turning the lock bars.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-19
12. Accessories
12.6.3 Dimensions
The following pictures give an overview about the measurements and dimensions of the 42" version and the
47".
12.6.3.1 Dimensions of the 42" version:
12-20 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12.6.3.2 Dimension of the 47" version:
12. Accessories
12.6.4 Tilting
Use an allen wrench size 2.5mm!
To adjust the tilting angle of the monitor,
• loosen the tilt angle fixation screw,
• adjust the position,
• tighten the screw again.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-21
12. Accessories
12.7 Long ceiling mount
First mount the screen bracket to the monitor, cf.
. Screen bracket (adapter plate)
The long ceiling mount fixes the monitors to the ceiling and allows setting the lower screen edge to a distance of the ceiling between 1235.5mm and 1614.5mm for the 42" versions, and between 1305mm and 1684mm for the
47" versions, respectively.
The monitors can be tilted by 20 degrees thanks to the ball point connection.
12-22 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.7.1 Scope of delivery
The short ceiling mount comprises 4 parts:
• The base plate with the cylinder which holds the telescope bar. This base plate will be mounted on the ceiling
• The telescope bar with the ball point connection to adjustable bar.
• The base plate with the ball point connection to the adjustable bar. This base plate will be mounted on the ceiling
• The adapter plate to attach to the screen bracket of the monitor with two hooks to lock the knurled bolts.
The screws to assemble the long ceiling bar are included. You will need a wrench 17mm.
The screws to fix the base plate to the ceiling have to be provided on site, cf. Required tools .
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-23
12. Accessories
12.7.2 Installation
The wall mount bracket is attached to the wall by means of 4 screws M8 (for specification of the screws, cf.
Required tools .). It is the same bracket for 42" and 47".
For drilling the holes in the ceiling, it is recommended to use a jig – take a sheet of paper
(A4) and copy the distances given in the drawing below.
• Drill 4 holes, 10mm, to the ceiling in the given distances!
• Attach the ceiling mounting plate.
• Slid in the telescope bar and lock its position by means of a screw M10x60. Secure the screw with a nut, and apply the black plastic cap.
• Complete the ball point connection between the telescope bar and the adjustable bar by using one of the included screws M10x60. Secure the screw with the nut and attach the black plastic cap. Also attach a black plastic cap to the already installed parallel screw on the telescope bar.
• Slide in the adjustable bar into the monitor mounting plate of the long ceiling mount. Fix its position by one of the included screws M10x60. Secure the screw with the nut and attach the black plastic cap.
12-24 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
• Hook in the knurled bolts of the monitor into the notches and the keyhole of the long ceiling adapter plate.
Lock the monitor by means of the left and right hook.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-25
12. Accessories
12.7.3 Dimensions
The following pictures give an overview about the measurements and dimensions of the 42" version and the
47".
12.7.3.1 Dimensions of the 42" version:
12-26 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12.7.3.2 Dimension of the 47" version:
12. Accessories
12.7.4 Tilting
Use an allen wrench size 2.5mm!
To adjust the tilting angle of the monitor,
• loosen the tilt angle fixation screw,
• adjust the position,
• tighten the screw again.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-27
13 Contact
Feel free to contact us if you have any further questions!
• Barco Control Rooms GmbH
An der Rossweid 5 • D-76229 Karlsruhe • Germany
Phone (49) (721) 6201-227 • Fax (49) (721) 6201-298
E-mail [email protected]
, Web www.barcocontrolrooms.de
• BARCO N.V.
President Kennedypark 35 • B-8500 Kortrijk • Belgium
Phone (32) (56) 36-8282 • Fax (32) (56) 36-82 51
E-mail [email protected]
,• Web www.barcocontrolrooms.com
• BARCO N.V. Media
Noordlaan 5 • B-8520 Kuurne • Belgium
Phone (32) (56) 36-8970 • Fa× (32) (56) 36-8386
E-mail [email protected]
,• Web www.barco.com
13. Contact
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
13-1
13. Contact
13-2 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
Advertisement
