Signature SG150-P Installation guide

Signature SG150-P Installation guide
SGT5000_100-150_UPS_GE01
GE Digital Energy
Power Quality
Operating Manual
Uninterruptible Power supply
Digital Energy™
SG Series
100 – 120 – 150 kVA
480 VAC UL / Series 0
Manufactured by:
GE Consumer & Industrial SA
General Electric Company
CH – 6595 Riazzino (Locarno)
Switzerland
T +41 (0)91 / 850 51 51
F +41 (0)91 / 850 51 44
www.gedigitalenergy.com
GE imagination at work
Model:
SG Series 100 – 120 - 150 kVA / Series 0
Issue by
Product Document Department – Riazzino - CH
Date of issue:
11/12/2008
File name:
OPM_SGS_USM_M10_M15_0US_V030
Revision:
3.0
Identification No.:
Up-dating
Revision
Concerns
Date
2.0
House-style GE Consumer & Industrial
01/30/2006
3.0
GE Digital Energy – Power Quality
11/12/2008
COPYRIGHT © 2008 by GE Consumer & Industrial SA
All rights reserved.
The information contained in this publication is intended solely for the purposes indicated.
The present publication and any other documentation supplied with the UPS system is not to be
reproduced, either in part or in its entirety, without the prior written consent of GE.
The illustrations and plans describing the equipment are intended as general reference only and are not
necessarily complete in every detail.
The content of this publication may be subject to modification without prior notice.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 2/82
Operating Manual SG Series 100 – 120 - 150 kVA
Dear Customer,
We thank you for selecting our products and are
pleased to count you amongst our very valued
customers at GE.
We trust that the use of the SG Series
Uninterruptible Power Supply system, developed
and produced to the highest standards of quality,
will give you complete satisfaction.
Please read carefully the Operating Manual, which
contains all the necessary information and describes
all you need to know about the use of the UPS.
Thank you for choosing GE !
START UP AND COMMISSIONING
A GE Global Services Field Engineer must perform start-up and
commissioning of the UPS. Please Contact GE. Global Services at least two
weeks prior to schedule start-up and commissioning at 1-800-637-1738, or
by E-mail at [email protected]
Distributed in the USA by:
g
GE Consumer & Industrial SA
General Electric Company
CH – 6595 Riazzino (Locarno)
Switzerland
www.gedigitalenergy.com
Your service contact:
g
GE Digital Energy
Power Quality
2501 Pecan Street
Bonham, TX 75418
T: +1 800-637-1738
F: +1 903-640-0533
E: [email protected]
http://www.gedigitalenergy.com/ups
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 3/82
Operating Manual SG Series 100 – 120 - 150 kVA
Preface
Congratulations on your choice of a SG Series Uninterruptible Power Supply (UPS). It will
help eliminate Load disturbances due to unexpected power problems.
This Manual describes the function of the UPS module, the purpose and location of the
switches, the meaning of the system events related to the front panel indication, and
provides procedures for starting and stopping the equipment.
Please refer to the accompanying Installations Guide, which describes how to prepare the
installation site, and it provides weight, dimensions and procedures for moving, installing
and connecting the UPS.
While every care has been taken to ensure the completeness and accuracy of this manual,
GE assumes no responsibility or liability for any losses or damages resulting from the use
of the information contained in this document.
NOTE !
SG Series 100 – 120 - 150 kVA is a product that needs to be installed by a licensed and
knowledgeable contractor.
We recommend that this manual be kept next to the UPS for future references.
If any problems are encountered with the procedures contained in this manual, please
contact your Service Center before you proceed.
This document shall not be copied or reproduced without the permission of GE.
Some of the information contained in this manual may be changed without notice to
reflect technical improvements.
Safety instructions
Read the safety instructions contained on the following pages carefully before the
installation of the UPS, options and Battery System.
Pay attention to the rectangular boxes included in the text:
They contain important information and warning concerning electrical connections and
personnel safety.
Parallel version secured with RPA
When included in the text, this symbol refers to operation needed
only for parallel system.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 4/82
Operating Manual SG Series 100 – 120 - 150 kVA
Table of contents
Page
1
IMPORTANT SAFETY INSTRUCTIONS ........................................................................................................ 7
2
INTRODUCTION.......................................................................................................................................... 10
3
DESCRIPTION.............................................................................................................................................. 11
3.1
3.2
BLOCK DIAGRAM AND MAIN ELEMENTS .............................................................................................................................. 11
OPERATION MODES....................................................................................................................................................................... 12
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
3.3
PARALLEL SYSTEM OPERATION................................................................................................................................................ 14
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.4
3.5
4
RECTIFIERS PARALLELED ON THE SAME BATTERY........................................................................................................... 16
RECYCLING AT THE END OF SERVICE LIFE........................................................................................................................... 17
LAYOUT SG Series 100 - 120 - 150 kVA................................................................................................................................. 18
CONTROL PANEL........................................................................................................................................ 19
5.1
5.2
6
CONTROL PANEL............................................................................................................................................................................. 19
TABLE OF FUNCTIONS AND INDICATIONS ON CONTROL PANEL.............................................................................. 19
LCD SCREEN................................................................................................................................................ 21
6.1
6.2
6.3
6.4
6.5
6.6
METERING MODE ............................................................................................................................................................................ 22
ALARMS............................................................................................................................................................................................... 25
PARAMETERS .................................................................................................................................................................................... 26
EDIT MODE......................................................................................................................................................................................... 28
USER PARAMETERS........................................................................................................................................................................ 31
EVENTS (ALARMS AND MESSAGES)......................................................................................................................................... 34
6.6.1
6.6.2
6.6.3
7
Introduction to the parallel system ............................................................................................................................................. 14
Features of RPA parallel system ................................................................................................................................................... 15
System control...................................................................................................................................................................................... 15
Synchronization.................................................................................................................................................................................... 15
Load sharing .......................................................................................................................................................................................... 15
LAYOUT........................................................................................................................................................ 18
4.1
5
Normal operation mode ................................................................................................................................................................... 12
Utility failure operation ..................................................................................................................................................................... 12
Utility recovery operation ................................................................................................................................................................ 13
Automatic Bypass ............................................................................................................................................................................... 13
Manual Bypass ..................................................................................................................................................................................... 13
Alarms list ................................................................................................................................................................................................ 34
Messages list.......................................................................................................................................................................................... 38
Event report SG Series........................................................................................................................................................................ 40
OPERATION ................................................................................................................................................. 41
7.1
PROCEDURES FOR SINGLE UPS................................................................................................................................................ 42
7.1.1
7.1.2
7.1.3
7.1.4
7.1.5
7.1.6
Start-up of the SG Series................................................................................................................................................................... 42
Maintenance shutdown (Load on Q2)......................................................................................................................................... 43
From Manual Bypass (Q2) to normal function VFI ................................................................................................................ 44
Complete UPS shutdown (No Load supply).............................................................................................................................. 45
Restore to normal operation after “total off”........................................................................................................................... 46
Restore to normal operation after EPO (Emergency Power Off)...................................................................................... 47
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 5/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.2
PROCEDURES FOR UPS FUNCTIONING AS FREQUENCY CONVERTER .................................................................... 48
7.2.1
7.2.2
7.2.3
7.2.4
7.3
PROCEDURES FOR PARALLEL SYSTEM .................................................................................................................................. 52
7.3.1
7.3.2
7.3.3
7.3.4
7.3.5
7.3.6
7.3.7
7.3.8
7.4
COMMUNICATION OPTIONS ...................................................................................................................................................... 78
OPTIONS IN UPS CABINET........................................................................................................................................................... 78
CONNECTION FOR OPTIONS...................................................................................................................................................... 79
8.3.1
Remote Signalling Box (RSB) ........................................................................................................................................................... 79
MAINTENANCE ........................................................................................................................................... 80
9.1
MAINTENANCE................................................................................................................................................................................. 80
9.1.1
9.1.2
9.1.3
9.1.4
9.1.5
9.1.6
9.1.7
10
Parallel System start-up ................................................................................................................................................................... 65
Maintenance system shutdown (Load supplied from Q2 on all Units) ........................................................................ 67
From Manual Bypass (Q2) to normal function VFI ................................................................................................................ 68
Separate a Unit from the parallel system (System Redundancy).................................................................................. 70
Reconnect a Unit to a parallel system ....................................................................................................................................... 71
Parallel system shutdown (No Load supply) ........................................................................................................................... 72
Restore to normal operation after “total off”........................................................................................................................... 74
Restore to normal operation after EPO (Emergency Power Off)...................................................................................... 76
OPTIONS ...................................................................................................................................................... 78
8.1
8.2
8.3
9
Parallel System start-up ................................................................................................................................................................... 52
Maintenance system shutdown (Load supplied from Q2 on all Units) ........................................................................ 54
From Manual Bypass (Q2) to normal function VFI ................................................................................................................ 55
Separate a Unit from the parallel system (System Redundancy).................................................................................. 57
Reconnect a Unit to a parallel system ....................................................................................................................................... 58
Parallel system shutdown (No Load supply) ........................................................................................................................... 59
Restore to normal operation after “total off”........................................................................................................................... 61
Restore to normal operation after EPO (Emergency Power Off)...................................................................................... 63
PROCEDURES FOR PARALLEL SYSTEM WITH COMMON BATTERY............................................................................ 65
7.4.1
7.4.2
7.4.3
7.4.4
7.4.5
7.4.6
7.4.7
7.4.8
8
Start-up of the SG Series as frequency converter................................................................................................................. 48
Complete UPS shutdown (No Load supply).............................................................................................................................. 49
Restore to normal operation after “total off”........................................................................................................................... 50
Restore to normal operation after EPO (Emergency Power Off)...................................................................................... 51
Service check ......................................................................................................................................................................................... 80
Fans and ventilation ........................................................................................................................................................................... 80
Other components with limited lifetime .................................................................................................................................... 80
Battery ...................................................................................................................................................................................................... 80
Long shut-down periods of the UPS-system .......................................................................................................................... 81
UPS room conditions and temperature..................................................................................................................................... 81
Long shut-down periods of the UPS-system .......................................................................................................................... 81
NOTES .......................................................................................................................................................... 82
10.1
NOTES FORM .................................................................................................................................................................................... 82
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 6/82
Operating Manual SG Series 100 – 120 - 150 kVA
1
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions for models SG Series 100 - 120 - 150 kVA that should be
followed during installation and maintenance of the UPS and battery.
GENERAL
-
Move the UPS in an upright position in its original package to the final destination room.
To lift the cabinets, use a forklift or lifting belts with spreader bars.
Check for sufficient floor and elevator loading capacity.
Check the integrity of the UPS equipment carefully.
If you notice visible damage, do not install or start the UPS.
Contact the nearest Service Center immediately.
WARNING! RISK OF ELECTRICAL SHOCK:
Do not remove covers, there are no user serviceable parts inside.
After switching off takes 5 minutes for the DC capacitors to discharge because a lethally high voltage
remains at the terminals of the electrolytic capacitors.
All maintenance and service work should be performed by qualified service personnel.
The UPS contains its own energy source (battery).
The field-wiring outlets may be electrically live, even when the UPS is disconnected from the utility.
Dangerous voltages may be present during battery operation.
The battery must be disconnected during maintenance or service work.
This UPS contains potentially hazardous voltages.
Be aware that the inverter can restart automatically after the utility voltage is restored.
INSTALLATION
-
This UPS must be installed and connected only by trained personnel.
Verify accurately during Commissioning and Maintenance of the UPS, for the following:
Damaged components, squeezed wires and cables, or not correctly inserted plugs.
After removing the sidewalls of the UPS, make sure that all earth connections when reassembling, are
correctly reattached.
This UPS is intended for use in a controlled indoor environment free of conductive contaminants and
protected against animals intrusion.
WARNING! HIGH EARTH LEAKAGE CURRENT:
Earth connection is essential before connecting to AC input!
Switching OFF the unit does not isolate the UPS from the utility.
Do not install the UPS in an excessively humid environment or near water.
Avoid spilling liquids on or dropping any foreign object into the UPS.
The unit must be placed in a sufficiently ventilated area; the ambient temperature should not exceed 95°F
(35°C).
Optimal battery life is obtained if the ambient temperature does not exceed 77°F (25°C).
It is important that air can move freely around and through the unit. Do not block the air vents.
Avoid locations in direct sunlight or near heat sources.
STORAGE
-
Store the UPS in a dry location; storage temperature must be within -13°F (-25°C) to 131°F (+55°C).
If the unit is stored for a period exceeding 3 months, the battery must be recharged periodically (time
depending on storage temperature).
-
The battery-voltage is dangerous for person’s safety.
When replacing the battery, use the same cells number, voltage (V), capacity (Ah).
All the battery used, shall be of the same manufacturer and date of production.
Proper disposal or recycling of the battery is required.
Refer to your local codes for disposal requirements.
Never dispose of battery in a fire: they may explode.
Do not open or mutilate battery: their contents (electrolyte) may be extremely toxic.
If exposed to electrolyte, wash immediately with plenty of water.
Avoid charging in a sealed container.
Never short-circuit the batteries.
When working with batteries, remove watches, rings or other metal objects, and only use insulated tools.
In case of air shipment, the cables +/- going to the battery fuses/terminals shall be disconnected and isolated.
BATTERY
-
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 7/82
Operating Manual SG Series 100 – 120 - 150 kVA
Safety instructions when working with battery
EXTERNAL BATTERY MUST BE INSTALLED AND CONNECTED TO THE UPS BY
QUALIFIED SERVICE PERSONNEL.
INSTALLATION PERSONNEL MUST READ THIS ENTIRE SECTION BEFORE HANDLING
THE UPS AND BATTERY.
DANGER!
Full voltage and current are always present at the battery terminals.
The battery used in this system can provide dangerous voltages, extremely high currents and a
risk of electric shock.
If the terminals are shorted together or to ground they may cause severe injury.
You must be extremely careful to avoid electric shock and burns caused by contacting battery
terminals or shorting terminals during battery installation.
Do not touch uninsulated battery terminals.
A qualified service person, who is familiar with battery systems and required precautions, must
install and service the battery.
The installation must conform to national and local codes.
Keep unauthorised personnel away from the battery.
The qualified service person must take these precautions:
1 Wear protective clothing, such as rubber gloves and boots and protective eye wear
Batteries contain caustic acids and toxic materials and can rupture or leak if mistreated.
Remove rings and metal wristwatches or other metal objects and jewelry.
Do not carry metal objects in your pockets where the objects can fall into the battery
cabinet.
2 Tools must have insulated handles and must be insulated so that they will not short battery
terminals.
Do not allow a tool to short between individual or separate battery terminals or to the
cabinet or rack.
Do not lay tools or metal parts on top of the battery, and do not lay them where they could
fall onto the battery or into the cabinet.
3 Install the battery as shown on the drawing provided with the battery.
When connecting cables, never allow a cable to short across a battery’s terminals, the
string of battery, or to the cabinet or rack.
4 Align the cables on the battery terminals so that the cable lug will not contact any part of
the cabinet or rack, even if the battery is moved.
Keep the cable away from any sharp metal edges.
5 Install the battery cables in such a way that the UPS or battery cabinet doors cannot pinch
them.
6 Do not connect the battery terminal to Ground.
If any battery terminal is inadvertently grounded, remove the source of the ground.
Contacting any part of a grounded battery can cause a risk of electric shock.
7 To reduce the risk of fire or electric shock, install the battery in a temperature and humidity
controlled indoor area, free of contaminants.
8 Battery system chassis ground (earth) must be connected to the UPS chassis ground (earth).
If you use conduits, this ground conductor must be routed in the same conduit as the
battery conductors.
9 Where conductors may be exposed to physical damage, protect the conductors in
accordance with all applicable codes.
10 If you are replacing the battery or repairing battery connections, shut OFF the UPS and
remove the battery fuses.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 8/82
Operating Manual SG Series 100 – 120 - 150 kVA
Safety symbols and warnings
Safety warnings
The text of this manual contains some warnings to avoid risk to the persons and to avoid damages to
the UPS system and the supplied critical loads.
The non-observance of the warnings reminding hazardous situations could result in human injury and
equipment damages.
Please pay attention to the meaning of the following warnings and symbols.
Throughout this manual the following symbols are defined:
WARNING, if instruction is not followed injury or serious equipment damage may
occur!
CAUTION, internal parts have dangerous voltage present.
Risk of electric shock!
PE (Earth) – GND (Ground)
PROTECTIVE GROUNDING TERMINAL:
A terminal which must be connected to earth ground prior to making any other
connection to the equipment.
A terminal to which or from which an alternating (sine wave) current or voltage
may be applied or supplied.
A terminal to which or from which a direct current or voltage may be applied or
supplied.
This symbol indicated the word “phase”.
This symbol indicates the principal on/off switch in the on position.
This symbol indicates the principal on/off switch in the off position.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 9/82
Operating Manual SG Series 100 – 120 - 150 kVA
2
INTRODUCTION
An Uninterruptible Power Supply (UPS) provides the power for critical loads that need a reliable,
continuous, disturbance free supply.
In case the power provided by the Utility Fails, or exceeds the permitted tolerances, the power to supply
the Load is provided by the Battery for the specified time at the rated Load (or longer at a reduced Load)
or until the Utility power returns.
SG Series is a true double conversion VFI (Voltage Frequency Independent) UPS system where the Load is
continuously supplied by the Inverter through the Rectifier.
In case of trouble on the Inverter Output Voltage, or when overload or short-circuit on the output occur,
the Load is instantly transferred to the Utility via the Automatic Bypass.
The UPS automatically returns to normal mode when the failure condition is restored.
Key features:
•
More Critical equipment supported
Rated at 0.8 Power Factor, SG Series delivers more real power than other UPS in the market.
With today’s trend toward power factor corrected loads, SG Series can support more total Load
than any other UPS available, allowing you to support a greater number of today’s enterprise
computing Power Factor Corrected (PFC) equipment.
•
No single point of failure
Redundant Parallel Architecture (RPA) is an exclusive GE technology.
With RPA, SG Series UPS are controlled in a true peer-to-peer configuration where all critical
elements and functions (including Bypass) are redundant.
SG Series is designed to be the most reliable power protection system available on the market
today.
•
High Efficiency
Using IGBT technology and Space Vector Modulation (SVM) strategy, SG Series offers low output
voltage distortion and provides efficiencies up to 93%.
•
Fully digital
Digital Signal Processor (DSP), Flash memory and SVM strategy, are the technology corner stones
of new age of power quality and power reliability.
•
Extremely flexible
Tailor made power protection to meet your individual installation requirements; SG Series offers
various options like input harmonic filters and our comprehensive JUMP software suite for mission
control and data protection to cover all your application needs.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 10/82
Operating Manual SG Series 100 – 120 - 150 kVA
3
DESCRIPTION
3.1
BLOCK DIAGRAM AND MAIN ELEMENTS
Fig. 3.1-1 Block diagram
The SG Series system can be divided into the following main elements:
Control System
SG Series is designed with microprocessor-controlled signal processing
circuits. The interface between the operator and the unit is provided by the monitoring system on the
front panel.
This monitoring system consists of an active mimic diagram, a keyboard and a backlit display.
Rectifier
The standard Rectifier consists of a 6-pulse SCR-bridge, which converts the 3phase Utility Voltage into a controlled and regulated DC-voltage.
This regulated DC-voltage is used to supply power to the Inverter, and to provide charging power to the
Battery.
Inverter
The Inverter converts the DC voltage into a three-phase AC-voltage with
constant amplitude and frequency, which is completely independent and isolated from the AC-input
voltage.
Automatic Bypass
The Automatic Bypass consists of a static semiconductor-switch (SSM: Static
Switch Module), used to provide an uninterrupted transfer of the Load from Inverter to Utility.
Back-feed Protection
All SG Series UPS's are equipped with an automatic system for the protection
against voltage back feeding towards Utility, through the Bypass (Applied Standard IEC 62040-1).
This protection works automatically by opening contactor K6 and K8 (in series with the thyristors of the
static switch) and eventually K7, and acts in case of internal defects of the system, or due to wrong
manipulations on the Manual Bypass Q2.
Manual Bypass
The Manual Bypass consists of a pair of manual switches (Q1 and Q2), which
removes the UPS from the Load for maintenance, while still supplying the Load with power directly from
the Utility.
Battery
accepted tolerances.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
The Battery supplies the DC power to the Inverter when the Utility is out of
Page 11/82
Operating Manual SG Series 100 – 120 - 150 kVA
3.2
OPERATION MODES
3.2.1 Normal operation mode
During normal operation, the Rectifier converts
input AC power to DC.
The DC power provides input power for the
Inverter and charging power for the Battery.
The Inverter converts the DC power to
continuous and regulated AC power, which
supplies the critical load.
The control panel reports the Battery charge
status and the expected backup time with the
actual load.
Fig. 3.2.1-1 Block diagram normal operation mode
3.2.2 Utility failure operation
When the Utility is no longer within acceptable
tolerances, the Battery will provide the DC power
to the Inverter.
The Inverter will maintain continuous AC power
to the Load until the Battery Voltage reaches the
lower limit of the Inverter operation capability.
During the discharge, the LCD screen displays
the estimated time the Battery can support the
critical load.
Prior to the Battery completely discharging, the
"stop operation" alarm (shutdown imminent)
warns the operator that the Battery is almost
discharged and the UPS is about to shut down.
Fig. 3.2.2-1 Block diagram Utility Failure operation
In case of parallel operation
With a parallel system for power capacity (see Section 3.3)
• With the Bypass Utility power available, a low Battery warning on any unit will cause the Load to
be transferred to Utility (after a selectable time delay).
• With Bypass Utility power not available, a low Battery warning on any unit will start the “stop
operation” timer (adjustable).
The Load will shut down at the end of the “stop operation” time period.
With a parallel system for redundancy (see Section 3.3)
• When a Battery low warning occurs on a unit not necessary to support the present load, this unit
will shut down after a timeout period (selectable).
The Load is shared between the other units
• As the warning occurs on one unit necessary to support the present load, the system starts the
"stop operation" timeout (selectable).
The Load will shut down at the end of the “stop operation” time period.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 12/82
Operating Manual SG Series 100 – 120 - 150 kVA
3.2.3 Utility recovery operation
As soon as the AC input power recovers, the Rectifier will
start automatically, supplying DC power to the Inverter
and recharging the Battery.
If the Inverter was previously shut down due to low
Battery, the Load will be initially powered by Utility
through the Automatic Bypass.
When the Battery is recharged enough to ensure a
minimum time of operation with the present load, the
Inverter will start automatically and the Load will be
transferred back to the Inverter.
Fig. 3.2.3-1 Block diagram Utility recovery operation
In case of parallel operation
When the AC input power recovers, the Rectifiers will start up sequentially, according to their
number in the parallel system. This minimizes the initial inrush current.
The Inverters will start up automatically, but only when the Battery has recharged enough for a
minimum runtime with the present load.
When enough Inverters to supply the Load have been restarted, the Load will be transferred from the
Automatic Bypass back to the Inverter output.
3.2.4 Automatic Bypass
In normal operation, the Load is supplied by the Inverter.
When the control system detects a fault in the Inverter,
an overload condition or a short-circuit condition, the
Automatic Bypass will transfer the critical Load to the
Utility without interruption.
When the Inverter recovers, or the overload or shortcircuit condition is corrected, the Load will be
automatically transferred back to the Inverter.
If the UPS is unable to return to normal mode following
an automatic transfer to Bypass mode, an alarm
condition will be initiated.
A Manual Bypass (operator initiated) will not be
considered as an alarm condition.
Fig. 3.2.4-1 Block diagram Automatic Bypass
In case of parallel operation
Each unit has it’s own internal Bypass. These units are continuously exchanging information, enabling
all of the internal Bypass circuits in a parallel system to operate simultaneously.
If the Inverter of a unit fails, it’s Bypass circuit remains available to the parallel system.
It is excluded only if the unit is separated from the common bus by opening it’s output switch Q1.
3.2.5 Manual Bypass
The Manual Bypass circuit consists of Q1 and Q2 manual
switches, which permits transfer of the Load directly to
the unconditioned AC power without interruption, leaving
the UPS available for maintenance.
Fig. 3.2.5-1 Block diagram Manual Bypass
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 13/82
Operating Manual SG Series 100 – 120 - 150 kVA
3.3
PARALLEL SYSTEM OPERATION
3.3.1 Introduction to the parallel system
Two or more equal power units can be paralleled to increase the output power (paralleling for capacity)
or to improve the overall reliability of an UPS system (paralleling for redundancy).
The outputs of parallel units are connected to a common power bus, and in normal operation the units
connected on the parallel bus share the Load equally.
The modular concept of SG Series allows parallel operation of up to 8 units, without using paralleling
switchgear, external bypass circuits or common control circuitry (see Fig. 3.3.1-1).
Parallel units for power capacity
Several units can be paralleled in order to achieve output power greater than the maximum power of a
single unit.
The maximum total power shared between the paralleled units is equal to the total installed nominal
power.
In the event of a failure of one unit, the power supplied by the UPS system becomes insufficient and the
Load will be transferred to the Utility Bypass source.
Parallel units for redundancy
The nominal power rating of the n+1 out of n redundant paralleled modules must be equal to or greater
than the required Load power.
The Load will be equally shared by the n units connected on the output bus.
Should one of the n paralleled units trip Off-line, the remaining (n+1) modules will supply the load,
maintaining conditioned power to the critical load.
From this results higher reliability and security for the Load plus a higher MTBF (Mean Time Between
Failures).
Fig. 3.3.1-1 Block diagram parallel system operation
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 14/82
Operating Manual SG Series 100 – 120 - 150 kVA
3.3.2 Features of RPA parallel system
The SG Series parallel system is designed to provide a complete Redundant Parallel Architecture, and
is free from common equipment.
Not only the Inverters are redundant, but also the Bypass functions are designed with redundant
modular concept.
When one UPS needs maintenance or service, the Load is powered by the other units supplying the
Load bus.
The redundant communication bus to which all units are connected keeps each unit informed about the
status of all the other units.
The control panel located on each unit allows controlling and monitoring the status of this unit.
3.3.3 System control
A high-speed redundant, serial communication bus guarantees the exchange of data and thus the
communication between the CPU's of each unit.
Each module controls it's own function and operational status and communicates with all other
modules, in order to act or react if necessary, adapting it to the new conditions.
3.3.4 Synchronization
All units are identical, but one unit is arbitrarily selected as the reference and all the other units
synchronize to this unit, which in turn, synchronizes to the Utility Bypass voltage, as long as the later is
within tolerances.
In case of reference failure, another unit in the parallel system is automatically chosen to take over the
reference role.
The Bypass Input for all the units of the parallel system must be supplied from the same AC source (no
phase shift allowed between them).
3.3.5 Load sharing
On each unit of the parallel system, Inverter Output Voltage and Current are measured and applied to a
Load sharing bus.
An eventual difference between the units is therefore automatically equalized.
NOTE !
It is strongly recommended that no transformers, automatic circuit breakers or
fuses should be inserted between the unit’s output and the Load common bus bars.
However, it is recommended that a disconnect or isolation switch be inserted.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 15/82
Operating Manual SG Series 100 – 120 - 150 kVA
3.4
RECTIFIERS PARALLELED ON THE SAME BATTERY
NOTE !
A parallel system with a Common Battery for two or more Rectifiers, requires a
particular installation and adequate setting of some parameters, (accessible
only through password), and can therefore only be done by a qualified
engineer from GE.
Usually each Rectifier-Inverter Unit runs with its own Battery.
In case of parallel units are running with a Common Battery (max. 4 UPS - see Fig 3.4-1), the sharing
circuit between individual Rectifier is integrated in the communication bus of the system in order to
assure an equal sharing of the Rectifiers output currents.
1–
Rectifier
2–
Inverter
3–
Automatic Bypass
4–
Manual Bypass
5–
Mains Power
6–
Load Bus Bar
7–
External Battery Fuse
8–
Battery
Fig. 3.4-1 Diagram RPA system with Rectifiers on Common Battery
Pay attention to the following recommendations:
•
The units delivered for this functioning mode needs a special parameters setting, so they must be
prepared in advance before the installation.
•
The installation must be performed only with the UPS system must be completely shut down.
•
The AC Rectifiers input power (5) must be the same, with clockwise phase rotation for each unit.
•
Each Rectifier must be set for the same floating DC voltage and the same Battery current limitation.
•
It is recommended to install the fuses / MCB (7) on each line connecting the Rectifiers to the
common Battery for maintenance / safety reasons.
•
In case one must be powered down for maintenance, switch-OFF the concerned unit before open
the DC fuses / MCB on the Battery line (7).
•
It is recommended to connect an external NO free contact “Battery Fuses” to the UPS and to enable
the function by setting the parameter (see Section 4.1 of the “Installation Guide”).
•
If an emergency generator set supply the UPS, and the free contact “Generator ON” is connected to
the Customer interface, connect a separate NO free contact on each parallel unit.
•
The parameters enabling the Battery test, both manual and automatic, must be set in the same
mode on all the units having the Rectifiers on Common Battery.
•
Do not connect the temperature sensor for automatic battery floating voltage compensation.
•
Do not enable the function Boost charge (parameter 87).
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 16/82
Operating Manual SG Series 100 – 120 - 150 kVA
3.5
RECYCLING AT THE END OF SERVICE LIFE
NOTE !
This product has been designed to respect the environment, using
materials and components respecting eco-design rules.
It does not contain CFCs (Carbon Fluor Clorid) or HCFCs (Halogen
Carbon Fluor Clorid).
GE, in compliance with environment protection recommends to the
User that the UPS equipment, at the end of its service life, must be
recovered conforming to the local applicable regulations.
WARNING !
Leads contained in the batteries is a dangerous substance for the
environment, therefore it must be correctly recycled by specialised
companies!
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 17/82
Operating Manual SG Series 100 – 120 - 150 kVA
LAYOUT
4.1
LAYOUT SG Series 100 - 120 - 150 kVA
SGT5000_100-150_UPS_GE02
SGT5000_100-150_UPS_03
4
1
2
3
4
J2
1
2
3
4
Fig. 4.1-2 SG Series general view with open doors
Fig. 4.1-1 SG Series general view
Fig. 4.1-4 Control Panel
1
SGT5000_100-150_Customer interface_03
Fig. 4.1-3 Manual operated switches
P4
Customer Interface Board
Q1
UPS output switch
Q2
Manual Bypass switch
SNMP
Advanced SNMP Card (option)
XA
Terminals for 24VDC Auxiliary Power Supply connection
XB
Terminals for EPO (Emergency Power Off) connection
2
3
4
P4
SNMP
1
2
3
XA
XB
4
Fig. 4.1-5 Connectivity Rack
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 18/82
Operating Manual SG Series 100 – 120 - 150 kVA
5
CONTROL PANEL
5.1
CONTROL PANEL
Fig. 5.1-1 Control Panel
5.2
TABLE OF FUNCTIONS AND INDICATIONS ON CONTROL PANEL
inverter on/off
inverter on/off
Key to switch the Inverter ON ( I )
(This key is also used to reset “total off” if pressed simultaneously with total off
push button).
Key for Inverter shutdown ( O )
Press key to transfers the Load to Utility.
Keep pressed for 5 seconds to shutdown the Inverter.
This key is also used as the EPO (Emergency Power Off) reset.
mute
Key to reset general alarm and buzzer.
test
Key to test the control panel LEDs and buzzer.
(Pressing this key causes all the LEDs to light and the buzzer to sound 3 times).
The push-button “total off” is protected by a red cover.
By pressing it, you immediately separate the UPS from Utility and the Load.
Attention: “total off” cannot disconnect the UPS from the Load with Q2 closed.
To reset “total off”:
push and hold the “total off” push-button and the “I” key
(inverter on) simultaneously for some seconds.
For parallel system: if “total off” is pressed on one unit connected to
the parallel bus (switch Q1 closed), all the units are separated from the load.
The “total off” reset must be done only on one unit connected to the parallel bus
(switch Q1 closed).
NOTE !
Special care must be taken in using this command, in order to
avoid accidental Load disconnection.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 19/82
Operating Manual SG Series 100 – 120 - 150 kVA
General alarm condition
It blinks when one or more alarm is activated. The internal buzzer is ON.
The LED remains lighted (with alarm condition still present) and the buzzer
stops as the key “mute” has been pressed.
alarm
LED ON indicates that a regular maintenance service is needed.
May be reset by a service technician only.
See Section 11 – Maintenance.
The LED is ON also when the output switch Q1 is open, indicating that the
Inverter is in service mode, not supplying the load.
service check
a)
b)
LED ON indicates that the Battery reserve lasts for only 3 more minutes
(selectable).
LED ON in case of overtemperature or overload >125% together with
missing Utility.
After the timeout the Inverter will shut down.
All LEDs ON indicate that the Battery is fully charged
LED a
Yellow:
• Fixed:
indicating last 25 % of Battery backup.
• Blinking: indicating Battery backup ≤ 5%.
LED b, c, d
Green:
• Each one indicating 25 % of Battery backup.
LEDs ON indicate the Load status of the UPS
LED d
LED c
LED b
LED a
red
yellow
green
green
Fig. 5.2-1 LEDs on synoptic diagram
(≥100 % load)
(100% load)
(66% load)
(33% load)
LEDs on synoptic diagram
LED 1
= Input Utility Rectifier (green)
LED 2
= Input Utility Bypass (green)
LED 3
= Rectifier ON (green)
LED 4a = Discharging (yellow)
LED 4b = Charging (green)
LED 5
= Inverter ON (green)
LED 6
= Load on Inverter (green)
LED 7
= Load on Utility (green)
LED 8
= Output Load Voltage (green)
LED 9
= Manual Bypass (Q2) ON (yellow)
User LCD Interface
Consist of an LCD screen, 4 lines with 20
characters each and six keys. It offers:
Fig. 5.2-2 LCD screen
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
•
UPS operating,
information.
•
History of events (alarms and messages).
•
Functionality can be programmed to meet
customer needs by changing parameters.
AC
and
DC
metering
Page 20/82
Operating Manual SG Series 100 – 120 - 150 kVA
6
LCD SCREEN
The user interface consists of a back lit LCD screen having:
•
4 lines with 20 characters (standard version for Latin characters).
and
•
6 keys (the function is described for each operating mode).
The operation is extremely simple and is structured on three important main menus related to the UPS
operation, as follows:
metering
A UPS must offer some metering information for the user to be able to examine the
operating status at any time.
alarms
In the event of Utility failures or abnormal functioning, the UPS must keep a history of
what has happened as a series of events.
parameters
The user must be able to program certain functions of the UPS (user parameters,
accessible without password) to his needs.
LCD screen standard version
metering
alarms
parameters
LCD screen
+
4 rows x
20 characters
–
ok
The 3 buttons existing on the left side of the screen are used to activate the operating modes, while the
buttons on the right side are used to carry out functions inside these operating modes.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 21/82
Operating Manual SG Series 100 – 120 - 150 kVA
6.1
METERING MODE
The metering mode is entered any time the metering button is pressed.
While in this mode the LCD will display a series of screens containing metering information.
In this mode the buttons perform the following functions:
metering
Scrolls forward to the next screen.
alarms
Abandons the metering mode and enters the alarms mode.
parameters
Abandons the metering mode and enters the parameters mode.
+
Scrolls forward to the next screen.
–
Scrolls backward to the previous screen.
ok
Displays the main screen for this mode.
Main screen
This screen displays the current status of the UPS in a condensed form.
The information offered by this screen consists of:
• The type of the machine: Family name, series number (P + unit number for parallel version from 1
to 8) and power range.
• The status of the load.
• The Load amount as a percentage of the nominal Load (referred to the most loaded phase).
• The estimated Battery backup time in minutes with the present load.
metering
alarms
parameters
SG Series S0 100kVA
LOAD ON INVERTER
LOAD = 84%
Autonomie = 12min
+
–
ok
Battery data screen
This screen displays:
• The Battery voltage.
• The Battery Current (negative values correspond to the discharge of the Battery).
• The temperature of the Battery (XXX indicates sensor disabled).
• The current charge level.
• The estimated backup time with the present load.
metering
alarms
Ub=540V Ib=
Battery Temp=
Charge Level=
Autonomy
=
+ 15A
+ 20 °C
87%
12min
parameters
+
–
ok
Bypass Utility data screen
This screen refers to the AC source supplying the Bypass. This screen displays:
• The frequency.
• The voltage levels of the three phase voltages.
m e te rin g
a la rm s
p a ra m e te rs
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
U T IL IT Y
f = 6 0 .0 H z
U1=276V U2=275V
U3=277V
+
–
ok
Page 22/82
Operating Manual SG Series 100 – 120 - 150 kVA
Rectifier Utility data screen
This screen refers to the AC source supplying the Rectifier.
This screen displays:
• Iout1 = output current Rectifier Bridge.
• Iout2 = output current 2nd Rectifier Bridge (optional 12 pulse Rectifiers only).
• The voltage levels between the three phases (line-to-line).
• The input frequency of the Rectifier.
m etering
alarm s
param eters
R EC TIFIER
U12=481V
Iout1 =133A
U23=480V
Iout2 = 0A
U31=482V
f=60.0H z
+
–
ok
Inverter data screen
This screen displays:
• The voltage level of the three phase voltages (line-to-neutral).
• The output frequency of the Inverter.
• The synchronization status of the Inverter with respect to Utility.
metering
alarms
parameters
INVERTER:
U1=277V
U2= 277V
U3=277V
Frequency = 60.0Hz
Synchronized
+
–
ok
Status Load screen
This screen displays:
• The Load level in kVA (for RPA: only this unit).
• The Load level as a percentage of the nominal rated Load (for RPA: only this unit).
• The source of the power supplied to the Load.
metering
alarms
parameters
LOAD ON UPS
Load
= 80.04kVA
Percentage = 80%
LOAD ON INVERTER
+
–
ok
Load on phases screen 1
This screen displays for each phase:
• The output phase voltage and current as RMS values (for RPA: total value of Parallel System).
• The output Load as percent (for RPA: respect to the rated power of Parallel System).
metering
alarms
parameters
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
LOAD ON PHASES
U1=277V I=101A 84%
U2=277V I= 95A 79%
U3=277V I= 93A 77%
+
–
ok
Page 23/82
Operating Manual SG Series 100 – 120 - 150 kVA
Load on phases screen 2
This screen displays for each phase:
• The Load active power (kW) (for RPA: total value of Parallel System).
• The Load apparent power (kVA) (for RPA: total value of Parallel System).
metering
alarms
parameters
LOAD ON PHASES
L1= 22.37kW 27.97kVA
L2= 21.05kW 26.31kVA
L3= 20.61kW 25.76kVA
+
–
ok
Miscellaneous screen
This screen displays:
• The temperature of the Inverter Bridge.
• The total operating time for the UPS (in hours).
• The total operating time for the Inverter (in hours).
metering
alarms
MISCELLANEOUS
InvHeatsink =
45 °C
UpsOperTime=
3125h
InvOperTime =
2135h
parameters
+
–
ok
Utility Faults Statistics screen
This screen displays:
• The total number of minor Utility faults (Bypass Utility out of tolerance faults).
• The total number of major Utility faults (Rectifier Utility out of tolerance faults).
• The total number of detected output overloads.
metering
alarms
UTILITY FAULTS STAT.
Minor
=
43210
Major
=
11267
Overloads=
654
parameters
+
–
ok
UPS identification screen
This screen displays:
• The UPS family and the power range.
• The software version.
• The serial number.
metering
alarms
parameters
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
UPS IDENTIFICATION
SG Series S0 100kVA
SW Version: x.xx
S/N: P0100-2006-0001
+
–
ok
Page 24/82
Operating Manual SG Series 100 – 120 - 150 kVA
6.2
ALARMS
The alarms mode is entered any time the alarms button is pressed.
The LCD will display a series of screens corresponding to the last 256 events, one event per screen.
The buttons perform the following functions:
metering
Abandons alarms mode and enters metering mode.
alarms
Next screen.
parameters
Abandons the alarms mode and enters the parameters mode.
+
Scrolls forward to the next screen.
–
Scrolls backward to the previous screen.
ok
Display the main screen for this mode.
The events displayed are the standard GE events as described in the Section 6.7 - EVENTS (Alarms and
Messages).
The information displayed includes:
• The exact date and time when the event occurred.
• The number of the event, 255 being the most recent event, and 0 the oldest.
• The standard GE code for the event and the machine status word.
• An explicit text description of the event.
metering
alarms
parameters
01.01.2006 22:11:51
NR=255 Status=4A61
4115:LOW BATTERY
VOLTAGE
+
–
ok
The initial screen of this mode is the one showing the most recent event.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 25/82
Operating Manual SG Series 100 – 120 - 150 kVA
6.3
PARAMETERS
The parameters mode is entered any time the parameters button is pressed.
The LCD will display a series of screens containing the user parameters, accessible without password
protection.
The buttons perform the following functions:
metering
Abandon parameters mode and enter metering mode.
alarms
Abandon parameters mode and enter alarms mode.
parameters
Scroll forward to the next screen.
+
Scroll forward to the next screen.
–
Select from the current screen the parameter to edit.
ok
Start the editing for the currently selected parameter.
NOTE !
During parameters mode there is no means to perform scroll back on the display.
Example of operation within parameters mode:
Purpose: to correct a wrong telephone number previously stored in Tel2.
1 – Entering parameters mode (parameters). The first screen is displayed.
metering
1
alarms
parameters
DATE AND TIME
D M Y
Date: 01.01.2006
Time: 12:45:07
+
–
ok
2 – Scroll to the next screen (+). The second screen is displayed.
metering
2
alarms
parameters
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
PROTOCOL SETUP
Modem enabled=N
Init=BEQV1X3&D0S0=2
Alarm= N
Delay=22s
+
–
ok
Page 26/82
Operating Manual SG Series 100 – 120 - 150 kVA
3 – Scroll to the next screen (+). The third screen is displayed.
metering
3
alarms
parameters
Tel1:002186394567
Tel1 enabled:
Tel2:004017464340
Tel2 enabled:
+
N
N
–
ok
4 – Move the selection (underscore cursor) to the next parameter in this page (-).
metering
4
alarms
parameters
Tel1:002186394567
Tel1 enabled:
Tel2:004017464340
Tel2 enabled:
+
N
N
–
ok
5 – Move the selection to the next parameter in page (-).
metering
5
alarms
parameters
Tel1:002186394567
Tel1 enabled:
Tel2:004017464340
Tel2 enabled:
+
N
N
–
ok
6 – Enter Edit mode for the currently selected parameter (ok).
metering
6
alarms
parameters
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
EDIT MODE
PHONE NUMBER 2
004017464340
+ SCROLL
- CHANGE
+
–
ok
Page 27/82
Operating Manual SG Series 100 – 120 - 150 kVA
6.4
EDIT MODE
The EDIT MODE is entered from the parameters mode when the ok button is pressed.
During this mode the LCD will display a special editing screen for the parameter being edited.
The screen contents during Edit mode is:
•
First line: the special operating mode.
•
Second line:
the name of the parameter being edited.
•
Third line:
the current value of the parameter.
•
Fourth line:
contains a condensed help text.
During the Edit mode the buttons perform the following functions:
metering
Exits Edit mode and enters metering mode; any changes are discarded.
alarms
Exits Edit mode and enters alarms mode; any changes are discarded.
parameters
Exits Edit mode and enters parameters mode; any changes are discarded.
+
Scrolls from editable position to editable position.
–
Changes the currently selected editable position.
ok
Returns to parameters mode after saving the changes.
Examples of operation during Edit mode
There are three types of parameters they differ in behavior during Edit mode.
Depending the type of parameters, there are different ways to select and to change the needed values.
Type 1: Parameters having a large range of values (numeric value).
As continuation of the previous example, the telephone number stored in “Tel2” must be changed:
1 – Move the selection (block cursor) to the next character (+).
metering
1
alarms
parameters
EDIT MODE
PHONE NUMBER 2
004017464340
+ SCROLL - CHANGE
+
–
ok
2 – Move the selection to the next character (+).
metering
2
alarms
parameters
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
EDIT MODE
PHONE NUMBER 2
004017464340
+ SCROLL - CHANGE
+
–
ok
Page 28/82
Operating Manual SG Series 100 – 120 - 150 kVA
3 – Change the selected character (-).
metering
3
alarms
parameters
EDIT MODE
PHONE NUMBER 2
005017464340
+ SCROLL
- CHANGE
+
–
ok
4 – Change the selected character (-).
metering
4
alarms
parameters
EDIT MODE
PHONE NUMBER 2
006017464340
+ SCROLL
- CHANGE
+
–
ok
5 – Press ok: the screen will return to parameters mode saving the new value.
m etering
5
alarm s
param eters
Tel1:002186394567
Tel1 enabled:
Tel2:006017464340
Tel2 enabled:
+
N
N
–
ok
Type 2: Parameters having a limited range of values.
For example the parameter Printer Baud Rate has the range {600, 1200, 2400, 4800 and 9600}.
There is no need to edit this parameter digit by digit.
By pressing the [–] button the next value within the range is automatically provided by the software.
1 – Enter Edit mode for Printer Baud Rate, initial value = 1200.
metering
1
alarms
parameters
EDIT MODE
PRINTER BAUDRATE
1200
+ SCROLL - CHANGE
+
–
ok
2 – Change to 2400.
metering
2
alarms
parameters
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
EDIT MODE
PRINTER BAUDRATE
2400
+ SCROLL - CHANGE
+
–
ok
Page 29/82
Operating Manual SG Series 100 – 120 - 150 kVA
3 – Change to 4800.
metering
3
alarms
parameters
EDIT MODE
PRINTER BAUDRATE
4800
+ SCROLL - CHANGE
+
–
ok
4 – Press ok: the screen will return to parameters mode saving the new value.
metering
4
alarms
parameters
PRINTER SETUP
Parity=O
Baud=4800
Bits=8 Handshake=XON
Print All = N
+
–
ok
Type 3: Boolean parameters used to simulate command buttons.
The Boolean parameters have a range of Yes/No.
Only the user performs the modification of the value.
These “Type 3” parameters are used to initiate an action. There are two possibilities:
A
1 – The user wants the UPS to start the action => the user sets the parameter to “Yes”.
2 – The UPS finishes the action => the UPS sets the parameter to “No”.
B
1 – The user wants the UPS to start the action => the user sets the parameter to “Yes”.
2 – The user wants to abort the action => the user sets the parameter to “No”.
The actions that can be performed using such software buttons are:
•
Print the metering information.
•
Print the last 256 events.
•
Print the values of the parameters.
•
Print all the information obtainable from the UPS.
Returning from the Edit mode
Normally the ok button is used to return from the Edit mode.
Then the UPS will perform some validity tests on the new value.
If these tests are successful then the new value is saved and used.
If these tests fail the Edit mode is not exited.
NOTE !
The validity tests performed by the UPS are not exhaustive.
You should not rely exclusively on these tests.
Care should be taken when modifying the values of the parameters.
For all parameters except the LCD Contrast parameter the new value is saved and used after the ok
button was pressed.
In the case of the LCD Contrast parameter the new value is used immediately in order to obtain a better
visual feedback.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 30/82
Operating Manual SG Series 100 – 120 - 150 kVA
6.5
USER PARAMETERS
Pressing the Parameters button displays a series of screens containing the user parameters on the LCD
panel.
This first parameter level in not protected by password, therefore the user can freely adapt these
parameters to their needs.
The meaning of the user parameters and their use is described below (buttons performance is described
to Section 7.3).
1.
Date and Time set-up
metering
alarms
parameters
DATE AND TIME
D M Y
Date: 01.01.2006
Time: 12:45:07
+
–
ok
Date
You can adjust the date of the real time clock existing in the UPS by the means of this
parameter.
The value you enter is thoroughly checked to be a correct date in the format “dd.mm.yy”.
Time
You can adjust the time of the real time clock existing in the UPS by means of this
parameter.
The value you enter is thoroughly checked to be a correct time in the format “hh.mm.ss”.
The time is specified in 24-hour format.
2.
Protocol Set-up
m etering
alarm s
param eters
PROTOCO L SETUP
M odem enabled= N
Init= BEQV1X3& D0S0=2
Alarm =N Delay=22sec
+
–
ok
Modem enabled
You can enable/disable with Y/N the remote control through modem calls by
using this parameter.
Init
This parameter presents the modem initialisation string.
It can be 39 characters long.
When editing this parameter the UPS considers that a blank character terminates
the string.
If no blank character is found then all 39 characters are used.
Alarm
This Y/N parameter controls the automatic events signalling through modem.
If this parameter is set to Yes the UPS itself will call the remote location when a
new event occurs.
Delay
This parameter controls the delay between the occurrence of a new event and the
modem dialing.
It is useful because since the events typically do not occur isolated but in certain
sequences, you can eliminate the need for multiple dial-outs for such a sequence
of events.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 31/82
Operating Manual SG Series 100 – 120 - 150 kVA
3.
Telephone numbers
m e te rin g
a la rm s
p a ra m e te rs
Tel1 :
Tel1 en ab led : N
Tel2 :
Tel2 en ab led : N
+
–
ok
Tel1
This parameter specifies a first telephone number to be used for modem dial-out.
The telephone number has a maximum 39 characters and cannot contain blanks.
If the desired number is shorter than 39 characters, the string will finish with blanks.
Tel1 enabled
This parameter Y/N specifies if the first telephone number will be used for dial-out.
Tel2
A second dial-out number.
Tel2 enabled
This parameter Y/N specifies if the second telephone number will be used for dial-out.
Tel3
A third dial-out number.
Tel3 enabled
This parameter Y/N specifies if the third telephone number will be used for dial-out.
Tel4
A fourth dial-out number.
Tel4 enabled
This parameter Y/N specifies if the fourth telephone number will be used for dial-out.
4.
LCD Display
m etering
alarm s
param eters
LCD Display
UPS NAM E: SG Series
Contrast = 9
Language = ENGLISH
+
–
ok
UPS Name
The user can choose the name of the UPS model shown on the main page (max. 7
characters).
LCD Contrast
This parameter controls the contrast of the LCD screen in ten steps.
It can be adapted depending on the room lighting.
LCD Language
This parameter allows the choice of language used to display the information.
Valid choices are English, German, Italian, Spanish, French, Finnish, Tschech, Slovak,
Polish and Portuguese.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 32/82
Operating Manual SG Series 100 – 120 - 150 kVA
5.
Printer Set-up
The UPS is capable of communicating to a serial printer, to printout disparate information.
Please be sure to have a serial printer, that is a printer with a serial RS232 interface.
This is the only printer-interface supported by the UPS.
m etering
alarm s
param eters
PRINTER SETUP
Baud=2400 Parity=O
Bits=8 Handshake=XON
Print All = N
+
–
ok
Baud Rate
This parameter controls the baud rate used for data transmission.
Although different values can be selected, you must select 2400 Baud, which is the
only valid parameter.
Parity
This parameter controls the parity used for data transmission.
Odd (O) even (E) and “no parity” (X) can be selected.
Nevertheless the only valid value is NO PARITY (X).
Bits
This parameter controls the length of the data word on the serial line during data
transmission 7 or 8 bits are offered as choice.
Please select 8 bits, as this is the only valid value.
Handshake
This parameter is used to determine the communication protocol used when printing.
Valid values are “XON” standing for the XON/XOFF protocol or “NO” standing for any
protocol.
Print All
This parameter Y/N is used to print all the available information in the sequence
metering, alarms, user and service parameters.
NOTE !
Please configure your printer with the following parameters: 2400/8/N (2400 bits/sec, 8
bits, no parity).
6.
Printer commands
m etering
alarm s
param eters
PRIN TER CO M M ANDS
Print M easures
=N
Print Alarm s
=N
Print Param eters
=N
+
–
ok
Print Measures
This Y/N parameter is used to print only the measurement data.
Print Alarms
This Y/N parameter is used to print only the sequence of all Alarms/Events.
Print Parameters
This Y/N parameter is used to print only the list of User and Service Parameters
NOTE !
After each printing command the corresponding parameter will be set again to N.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 33/82
Operating Manual SG Series 100 – 120 - 150 kVA
6.6
EVENTS (ALARMS AND MESSAGES)
Each of the following listed events can be displayed on the LCD screen or on PC where the “PowerJump
Manager” or “PowerJump DataShield” is installed.
Alarms and Messages are differently specified because the alarms are indicating an abnormal
functioning of the UPS (which are additionally signalled with the LED alarm and acoustically with the
buzzer), while the messages indicate the various states of operation of the UPS (stored in the events list,
but not activating the LED alarm and the buzzer).
When in the alarms mode, the LCD screen displays a time ordered sequence of screens corresponding
to the last 256 alarms and messages, each screen indicating:
metering
01.01.2005 12:45:07
NR=255 Status=4A61
4115: LOW
BATTERY VOLTAGE
alarms
parameters
+
–
ok
1- The date and time when the event occurred.
2- The number of the event (255 = the most recent).
The standard code and the status word.
3- Code with an explicit text description of the events.
6.6.1 Alarms list
Code
4000
4004
Alarms
Meaning
SETUP VALUES
LOST
UPS
FAILURE
Parameters are lost and have been replaced with default values.
Call nearest Service Center for intervention.
The master unit detected the slave unit missing on the
communication bus even though switch Q1 is still closed.
The u-switch mounted on the Rectifier Input Fuses indicates a
blown fuse, and consequently shut down.
Clearance of this condition allows you to restart the Rectifier.
K4 not closed despite a closing command being issued.
Signalled by auxiliary contact.
Rectifier cannot start.
K4 not open despite an opening command being issued.
Signalled by auxiliary contact.
Utility remains connected to Rectifier bridge.
This function, when enabled on input programmable relays
(password required), warns the user about the external Battery
Fuses failure or MCB opening, signalled by NO free contact.
Temperature sensor indicates an over temperature on the
Rectifier Bridge.
Only alarm is given.
The Rectifier, when in Off state, cannot start as long as this
condition persists.
The temperature sensor inside the input transformer winding
indicates over temperature.
Only the alarm is given.
The Rectifier, when in Off state, cannot start as long as this
condition persists.
Rectifier Input Utility is out of tolerance (voltage, frequency or
phase).
4100
RECTIFIER FUSES
FAILURE
4102
K4 CLOSING
FAILURE
4103
K4 OPENING
FAILURE
4104
BATTERY
FUSES
4105
RECTIFIER
OVERTEMPERATURE
4106
RECTIFIER
TRANSFORMER
OVERTEMPERATURE
4110
RECTIFIER UTILITY
OUT OF TOLERANCE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 34/82
Operating Manual SG Series 100 – 120 - 150 kVA
Code
Alarms
4115
LOW BATTERY
VOLTAGE
4116
HIGH BATTERY
VOLTAGE
4117
BATTERY
EARTH FAULT
4118
BATTERY FAULT
4130
TURN ON RECT.
OR SHUTDOWN UPS
4140
RECTIFIER
CONTROL FAILURE
4301
INVERTER
FUSES FAILURE
4304
K7 CLOSING
FAILURE
4305
K7 OPENING
FAILURE
4307
INVERTER
TRANSFORMER
OVERTEMPERATURE
4308
DC FUSES
FAILURE
4309
DRIVER
FAILURE
4312
INV. VOLTAGE
OUT OF TOLERANCE
4320
ISMAX
DETECTION
4340
INVERTER
CONTROL FAILURE
4404
K6 CLOSING
FAILURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Meaning
The Battery has been discharged and reached “stop operation”
time-out (default 3 minutes), and the Inverter will be shut down.
It will restart automatically only when the Battery has recharged
enough for a minimum runtime.
Dangerous high DC Voltage caused Inverter shutdown.
Inverter restarts automatically after Battery returns to floating
voltage.
A leakage current to earth has been detected on the DC circuit.
During battery test the voltage falls under the critical level
(depending setting parameters).
Battery test is stopped.
Rectifier and Inverter are OFF.
The DC power supply is discharging the Battery.
Rectifier must be restarted or Battery must be disconnected in
order to avoid damage.
Rectifier Voltage hasn’t reached the set value (probably fault on
regulation loop).
LED Rectifier on control panel is blinking.
Inverter Output Fuses blown (F5, F6 and F7).
Inverter can be started manually after replacement of the fuses.
K7 not closed despite a closing command being issued.
Signalled by auxiliary contact.
Load will be supplied by Utility.
K7 not open despite an opening command being issued.
Signalled by auxiliary contact.
Load will be supplied by Utility.
The temperature sensor of the Inverter Transformer indicates
over temperature.
Elapsed “stop operation” time, Inverter shutdown.
With Utility OK, Load is transferred on Utility.
Blown input DC fuse(s) F1 of the Inverter.
Inverter cannot be started as long as present.
An abnormal condition has been detected on one or more
power modules of the Inverter (temperature or over current).
Inverter shutdown and cannot be started as long as the alarm is
present.
Inverter Output Voltage is out of the tolerances (± 10%).
Inverter is switched OFF.
Detection of Inverter Bridge (Is) current limit causing the Inverter
OFF and automatic re-start.
After 3 times the Inverter switches-Off, and it can be restarted
manually.
The “Slave” oscillator is not in synchronized with the Master;
thus causing the shutdown of it’s Inverter.
If after a restart the condition remains, the LED inside the
Inverter symbol on the panel will not light up, indicating that this
Inverter cannot supply the Load anymore.
K6 open despite a closing command being issued.
Signalled by auxiliary contact.
The Load cannot be supplied by Automatic Bypass.
Page 35/82
Operating Manual SG Series 100 – 120 - 150 kVA
Code
Alarms
Meaning
4405
K6 OPENING
FAILURE
4406
SSM
FAILURE
4408
K8 CLOSING
FAILURE
4409
K8 OPENING
FAILURE
4410
BYPASS UTILITY
OUT OF TOLERANCE
4420
K3 CLOSING
FAILURE
K6 closed despite an opening command being issued.
Signalled by auxiliary contact.
A faulty current has been detected in the static-switch causing
the opening of the contactor K6 for 10 seconds.
After 3 times K6 remains definitively open.
The alarm reset can be done only from Service Center.
K8 not closed despite a closing command being issued.
Signalled by auxiliary contact.
The Load cannot be supplied by Automatic Bypass.
K8 closed despite an opening command being issued.
Signalled by auxiliary contact.
The Utility Bypass Voltage is out of the tolerances (± 10%).
K6 opens, synchronization with Utility is inhibited and transfer to
Utility is blocked.
K3 open despite a closing command.
Inverter is switched OFF.
It can be restarted manually after recovery of the alarm
condition.
K3 not open despite an opening command.
Be aware the DC Capacitors could remain charged.
The Load supplied by Utility exceeds the Inverter power.
The Load remains supplied by Utility until the alarm stays ON.
A malfunction on the UPS ventilation system was detected.
No change for UPS operation.
Call immediately Service Center for intervention.
Load is locked on Utility because 3 transfers on Utility have been
detected in a short time (default 30 seconds).
The transfer will be free after a time defined in parameter
(default 30 seconds).
Load is transferred to Utility because the error detector detected
a disturbance on the output voltage.
Alarm after detection of an EPO from an external safety device
connected on Customer Interface Board.
Consequently K3, K4, K6, K7, K8 open, Rectifier, Inverter and SSM
are switched Off.
The UPS-System is in an overload condition >125% on Inverter,
or >150% on Utility.
With Utility unavailable, a sequence of “stop operation” starts.
Time out depends on Load quantity.
With Utility Bypass supply available and load >115%, the Load is
transferred on Utility.
Load will be transferred again automatically on Inverter when
Load <100%.
The voltages of Utility and Inverter are not synchronized, which
causes the opening of K6.
Detection of Battery over temperature condition.
Can be deactivated by Service Center.
In case of Utility Failure, with the actual Load, the run time would
be below stop operation time (default 3 minutes).
K3 OPENING
FAILURE
NO INVERTER
POWER
4421
4520
4522
FAN
FAILURE
4530
LOAD LOCKED
ON UTILITY
4531
LOAD ON UTILITY BY
ERROR DETECTOR
4563
EMERGENCY OFF
ACTIVATED
4570
OVERLOAD
4571
OVERLOAD:
LOAD ON UTILITY
4581
4697
4698
INVERTER AND
UTILITY NOT SYNCH.
BATTERY
OVERTEMPERATURE
BATTERY POWER
INSUFFICIENT
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 36/82
Operating Manual SG Series 100 – 120 - 150 kVA
Code
Alarms
4700
DC LOW
4900
LOAD LOCKED
ON INVERTER
4955
OVERTEMPERATURE
4998
4999
LOAD OFF DUE TO
EXTENT. OVERLOAD
LOAD OFF DUE
TO UBATT. OR TEMP.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Meaning
Battery voltage is at the lowest limit.
Will stay Off Inverter until the battery voltage reaches the value
in parameter.
The Load is locked on Inverter after 3 Load transfers within 30
seconds.
After time out (default 30 seconds) Bypass will be free.
An over-temperature condition has been detected on Inverter.
Elapsed “stop operation” time, Inverter shutdown.
With Utility OK, Load is transferred on Utility.
Load Off after time-out of “stop operation” for overload on
Inverter or Bypass (time depending on the % of overload).
Load Off after time-out of “stop operation” with missing Utility
due to Battery low voltage or over-temperature condition.
Page 37/82
Operating Manual SG Series 100 – 120 - 150 kVA
6.6.2 Messages list
Code
Message
Meaning
4002
WATCHDOG
RESET
The microprocessor has detected an incorrect operation:
Transfers the Load on Utility and performs a program reset.
The Inverter will restart automatically and will supply the Load.
Rectifier Input Utility is again within the admitted tolerance
(voltage, frequency and phase).
Start of Manual or Automatic Battery Test.
4111
4119
4120
4161
4162
RECTIFIER
UTILITY OK
BATTERY TEST
STARTED
BATTERY TEST
STOPPED
RECTIFIER
ON
RECTIFIER
OFF
4163
GENERATOR
ON
4164
GENERATOR
OFF
4302
INVERTER
CANNOT BE
TURNED ON
4303
4361
4362
4411
4500
4521
4534
4535
4536
INVERTER
CANNOT BE
TURNED OFF
INVERTER
ON
INVERTER
OFF
BYPASS UTILITY
OK
COMMAND
LOAD OFF
NO BYPASS
POWER
MULTIPLE LOAD
TRANSFER
BYPASS
LOCKED
BYPASS
FREE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
End of Manual or Automatic Battery Test.
Rectifier started.
Rectifier shutdown.
Customer Interface Board (X1 - 11, 22) received a Gen-set ON
signal.
Operating mode depend on setting of Parameters.
Customer Interface Board (X1 - 11, 22) received a Gen-set OFF
signal.
Function Bypass enabled depends on setting of parameter.
Inverter cannot be switched on because one of the following
conditions is still present:
− Over Temperature
− Low Battery Voltage
− Inverter Fuses
− Overload
− K7 opening Failure
− High Battery Voltage
− DC Low
− EPO
Inverter cannot be switched OFF, because the Load cannot be
switched to Utility (voltage out of tolerance, not synchrony, BP
blocked).
The command to start the Inverter has been activated on the
control panel.
The command to switch OFF the Inverter has been activated by
the control panel or automatically for alarm presence.
Bypass Input Utility is again within tolerance (voltage, frequency
and phase).
Disconnection of the Load by opening K6 and K7 for:
EPO / total off / Overload / stop operation.
With the Load supplied by Automatic Bypass, a Utility Failure or
K6 opening occurred.
2 transfers Inverter- Utility have been detected in a short time,
(default 30 seconds).
Bypass is not available.
Contactor K6 and K8 are open, SSM deactivated.
Bypass is enabled.
Contactor K6 is closed.
Page 38/82
Operating Manual SG Series 100 – 120 - 150 kVA
Code
Message
Meaning
4561
TOTAL
OFF
DETOUR
ON
DETOUR
OFF
COMMAND
LOAD ON UTILITY
COMMAND
LOAD ON INVERTER
NO MORE
OVERLOAD
INVERTER AND
UTILITY
SYNCHRONIZED
COMMAND
NOT TO
SYNCHRONIZE
COMMAND TO
SYNCHRONIZE
Q1
OPEN
Q1
CLOSED
Push-button “total off” on the UPS Control Panel has been
pressed, with the output circuit switch Q1 closed.
The auxiliary contact indicates that Manual Bypass Q2 was
closed.
The auxiliary contact indicates that Manual Bypass Q2 was
opened.
The control unit received a command to transfer the Load on
Utility.
The control unit received a command to transfer the Load on
Inverter.
End of the overload condition detected with alarm 4570.
4562
4564
4567
4568
4572
4580
4582
4583
4602
4603
4699
BATTERY TEST
IMPOSSIBLE
4763
REMOTE CONTROL
ON
4764
REMOTE CONTROL
OFF
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
The voltages of Inverter and Utility Bypass are synchronized.
Command not to synchronize with Utility.
Command to synchronize with Utility.
The auxiliary contact indicates that the output switch Q1 was
opened.
The auxiliary contact indicates that the output switch Q1 was
closed.
Automatic Battery Test is not possible due to:
− No Utility Rectifier or Bypass.
− Battery not fully charged.
− Load is below 10% or above 80%.
Test is postponed for 1 week.
Inverter can be started or shutdown by remote control.
Commands source can be chosen depending on the value of
parameter (Service only):
0 = Only local panel.
1 = Only serial port on CI.
2 = Both.
Inverter cannot be started or shutdown by remote control.
Commands source can be chosen depending on the value of
parameter (Service only):
0 = Only local panel.
1 = Only serial port on CI.
2 = Both.
Page 39/82
Operating Manual SG Series 100 – 120 - 150 kVA
6.6.3 Event report SG Series
In case of failure or malfunctioning, before calling the nearest Service Center, please note the most
important data of your UPS and the most recent events.
In order to make the diagnosis easier from our Diagnostic Centre we suggest you make a copy of this
page, fill it out with the requested data and send it by fax.
Unit No.:
__ __ __ __ __ - __ __ __ __ - __ __ __ __
Series No.:
Customer:
...................................…………….....…….
Place:
......................…......................…………………………...…........
Date:
...……..... / ..…......... / ....……….…….....
Sent by:
..…...........……..............…………………………............….......…
1.
Record the exact UPS status on the panel
when the failure appeared.
2.
‰ ON
‰ ON
‰ ON
‰ ON
‰ ON
‰ ON
‰ ON
‰ ON
‰ ON
‰ ON
.....................
.....................
‰ OFF
‰ OFF
‰ OFF
‰ OFF
‰ OFF
‰ OFF
‰ OFF
‰ OFF
‰ OFF
‰ OFF
%
Minutes
Description of repair actions taken:
....................................................................................................
....................................................................................................
....................................................................................................
Actual situation:
....................................................................................................
....................................................................................................
....................................................................................................
UPS rating:
……….….. kVA
On the LCD panel, enter the alarms mode and record
the alarms/messages in the list below indicating at
least 5 events before the failure time.
Remark: exact data and time are very important.
Event
No.
LED 1
LED 2
LED 3
LED 4a
LED 4b
LED 5
LED 6
LED 7
LED 8
LED 9
LOAD
BATTERY
……..…..
Event
Code
UPS
Status
Date
Time
h. m. s
255
254
253
252
251
250
249
248
247
246
245
244
243
242
241
240
239
238
237
236
235
234
233
232
231
230
Remarks:
................................................................................................................................................................................................................................
................................................................................................................................................................................................................................
................................................................................................................................................................................................................................
................................................................................................................................................................................................................................
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 40/82
Operating Manual SG Series 100 – 120 - 150 kVA
7
OPERATION
This symbol refers to the operations of a parallel system.
NOTE !
Verify for correct input/output cabling before connecting Utility to the
UPS.
Open only the front door, do not remove any panels.
Now you can initiate the start-up procedure of the UPS system.
There is no need for specific knowledge if you follow carefully the stepby-step instructions given below.
But we recommend, that at least the initial procedure, should be
performed by an instructed person.
Check after every step for correct reaction of the UPS (LED’s on the panel),
and correct voltage and current measurements, before you proceed to
the next step.
If you encounter any problems during the following procedures, you
should not continue, but contact GE Global Services.
Find on the following pages the descriptions of the various procedures of start-up and
shutdown for single and parallel UPS’s, divided into the following principal chapters:
7.1
PROCEDURES FOR SINGLE UPS
7.2
PROCEDURES FOR UPS FUNCTIONING AS FREQUENCY CONVERTER
7.3
PROCEDURES FOR PARALLEL SYSTEM
7.4
PROCEDURES FOR PARALLEL SYSTEM WITH COMMON BATTERY
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 41/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.1 PROCEDURES FOR SINGLE UPS
7.1.1 Start-up of the SG Series
Verify with open front door: Switch Q1 and Q2 must be open (Pos. O).
1. Connect the Utility power on the UPS.
(In case of separate inputs for Rectifier and
Bypass, connect both).
• Power supply starts up.
Indicated with flashing alarm and buzzer
sound.
• LED’s as indicated will be lit.
• Press mute, to reset alarm and buzzer.
2. Close Q1 (Pos. I).
• Bypass Utility connects to the output.
• Rectifier starts automatically, blinking LED
indicates Soft-start.
• At the end of Rectifier Soft-start, LED
remains lit.
3. Connect the Battery to the UPS by closing the Battery Switch or Fuses, in case of
External Battery.
4. Press “inverter on” ( I ) key.
• Soft-start of Inverter indicated with
blinking LED.
• At the end of Soft-start the LED remains
lit.
• Automatic transfer from Bypass to
Inverter.
• UPS output LED indicates Load on
Inverter.
The LCD must display on the main screen the status “LOAD ON INVERTER”.
END OF PROCEDURE
NOTE !
The Battery must be charged for at least 10 hours, in order to ensure the full
backup runtime in the case of a Utility Failure.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 42/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.1.2 Maintenance shutdown (Load on Q2)
Initial status:
Load supplied from Inverter.
1. Press “inverter off” ( O ) key and hold until
the LED inside the Inverter symbol turns
OFF.
• Load is transferred to Utility.
• Inverter shuts down.
• LED Inverter must be OFF.
The LCD screen must display the status “LOAD ON BYPASS”.
2. Close Q2 (Pos. I).
• Load is now supplied parallel through
Bypass and Q2.
• LED for Manual Bypass lights up.
3. Open Q1 (Pos. O) and then press “total off”
button.
• Load is now supplied from Manual Bypass.
• Rectifier shuts down and all output and
input contactors are opened.
The LCD panel must display the main screen, indicating the status “LOAD OFF”.
4. Disconnect the Battery from the UPS in case
of External Battery.
• Wait 5 minutes for DC-Link Capacitors
discharge.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 43/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.1.3 From Manual Bypass (Q2) to normal function VFI
Initial status:
Load supplied from Manual Bypass.
1. Close Q1 (Pos. I).
• Bypass connects to Load.
LED Load on Bypass lights up.
• Rectifier starts automatically and LED
in Rectifier symbol and LED Battery
charge light up.
2. Open Q2 (Pos. O).
• LED Manual Bypass turns OFF.
3. Connect the Battery to the UPS by closing the Battery Switch or Fuses, in case of
External Battery .
4. Press “inverter on” ( I ) key.
• Soft-start of Inverter, indicated with
blinking LED.
• At the end of Soft-start the LED
remains lit.
• Automatic transfer from Bypass to
Inverter.
• UPS output LED indicates Load on
Inverter.
The LCD must display on the main screen the status “LOAD ON INVERTER”.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 44/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.1.4 Complete UPS shutdown (No Load supply)
NOTE !
The Load must be disconnected.
Initial status:
Load supplied from Inverter.
1. Press “total off” button.
• Load is disconnected from UPS.
• Rectifier is shut down and all output and
input contactors will be opened.
• LED’s, Rectifier, Inverter and Load are OFF.
2. Open Q1 (Pos. O).
• LED service check lights up.
3. Disconnect the Battery from the UPS in case
of External Battery.
• Wait 5 minutes for DC-Link Capacitors
discharge.
4. Disconnect the Utility.
• All LED’s are OFF.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 45/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.1.5 Restore to normal operation after “total off”
View of the panel after pressing the button
“total off”.
• All Contacts are open.
• Rectifier, Inverter and Static-Switch
shutdown.
1. Reset “total off” by pressing and holding
the “total off” button and then the
“inverter on” ( I ) key simultaneously
until Load is supplied from Bypass and
the Rectifier starts.
• Output connects to Bypass Utility.
• Rectifier starts with blinking LED.
• At the end of Soft-start the LED
remains lit.
• The LCD screen shows: “LOAD ON BYPASS”.
• Press mute, to reset alarm and buzzer.
2. Connect the Battery to the UPS by closing the Battery Switch or Fuses, in case of
External Battery.
3. Press “inverter on” ( I ) key.
• Soft-start of Inverter indicated with
blinking LED.
• At the end of Soft-start the LED
remains lit.
• Automatic transfer from Bypass to
Inverter.
• UPS output LED indicates Load on
Inverter.
The LCD must display on the main screen the status “LOAD ON INVERTER”.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 46/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.1.6 Restore to normal operation after EPO (Emergency Power Off)
UPS panel after activation of
EPO (Emergency Power Off) with
Utility
not
available,
i.e.
complete shutdown of the UPS.
In this case wait until Utility is
again available, then proceed to
restart the UPS as described
below. Points 1 through 3.
UPS panel after activation of EPO
(Emergency Power Off) with Utility
available.
• All Contacts are open.
• Rectifier, Inverter and Static-Switch
shutdown.
1. Reset the EPO (Emergency Power Off)
button.
• Press mute, to reset alarm and buzzer.
2. Press “inverter off” ( O ) key.
• Output connects to Bypass Utility.
• Rectifier starts with blinking LED.
• At the end of Soft-start the LED
remains lit.
The LCD screen shows: “LOAD ON BYPASS”.
3. Press “inverter on” ( I ) key.
• Inverter starts with blinking LED.
• At the end of Soft-start the LED
remains lit.
• Automatic transfer from Bypass to
Inverter.
• UPS output LED and LCD screen
indicate both: “LOAD ON INVERTER”.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 47/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.2 PROCEDURES FOR UPS FUNCTIONING AS FREQUENCY CONVERTER
When the SG Series functions as a Frequency Converter, the Automatic Bypass and Manual
Bypass functions are disabled.
Therefore the Load cannot be transferred to Utility in case of overload, short circuit, or Inverter
failure.
In situations where the UPS needs to be shutdown for maintenance purposes, also the Load
must be shutdown or disconnected
7.2.1 Start-up of the SG Series as frequency converter
Verify with open front door: Switch Q1 must be open (Pos. O).
1. Connect the Utility power on the UPS.
• Power supply starts up.
Indicated with flashing alarm and buzzer sound.
• LED’s as indicated will be lit.
• Press mute, to reset alarm and buzzer.
2. Close Q1 (Pos. I).
• Rectifier starts automatically, blinking LED
indicates Soft-start.
• At the end of Rectifier Soft-start, LED remains lit.
3. Connect the Battery to the UPS by closing the Battery Switch or Fuses, in case of
External Battery.
4. Press “inverter on” ( I ) key.
• Soft-start of Inverter indicated with blinking LED.
• At the end of Soft-start the LED remains lit.
• UPS output LED indicates Load on Inverter.
The LCD must display on the main screen the status “LOAD ON INVERTER”.
END OF PROCEDURE
NOTE !
The Battery must be charged for at least 10 hours, in order to ensure the full
backup runtime in the case of a Utility Failure.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 48/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.2.2 Complete UPS shutdown (No Load supply)
NOTE !
The Load must be disconnected.
Initial status:
Load supplied from Inverter.
1. Press “total off” button.
• Load is disconnected from UPS.
• Rectifier is shut down and all output
and input contactors will be opened.
• LED’s, Rectifier, Inverter and Load are
OFF.
2. Open Q1 (Pos. O).
• LED service check lights up.
3. Disconnect the Battery from the UPS in
case of External Battery.
• Wait 5 minutes for DC-Link Capacitors
discharge.
4. Disconnect the Utility.
• All LED’s are OFF.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 49/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.2.3 Restore to normal operation after “total off”
View of the panel after pressing the button
“total off”.
• All Contacts are open.
• Rectifier,
Inverter and Static-Switch
shutdown.
1. Reset “total off” by pressing and holding
the “total off” button and the “inverter
on” ( I ) key simultaneously until the
Rectifier starts.
2. Connect the Battery to the UPS by closing the Battery Switch or Fuses, in case of
External Battery.
3. Press “inverter on” ( I ) key.
• Soft-start of Inverter indicated with
blinking LED.
• At the end of Soft-start the LED
remains lit.
• UPS output LED indicates Load on
Inverter.
The LCD must display on the main screen the status “LOAD ON INVERTER”.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 50/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.2.4 Restore to normal operation after EPO (Emergency Power Off)
UPS panel after activation of EPO
(Emergency Power Off) with Utility
not available, i.e. complete
shutdown of the UPS.
In this case wait until Utility is
again available, then proceed to
restart the UPS as described
below. Points 1 through 3.
UPS panel after activation of EPO
(Emergency Power Off) with Utility
available.
• All Contacts are open.
• Rectifier, Inverter and Static-Switch
shutdown.
1. Reset the EPO (Emergency Power Off)
button.
• Press mute, to reset alarm and buzzer.
2. Press “inverter off” ( O ) key.
• Rectifier starts with blinking LED.
• At the end of Soft-start the LED
remains lit.
• The LCD screen shows: “LOAD OFF”.
3. Press “inverter on” ( I ) key.
• Inverter starts with blinking LED.
• At the end of Soft-start the LED
remains lit.
UPS output LED and LCD screen
indicate both: “LOAD ON INVERTER”.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 51/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.3 PROCEDURES FOR PARALLEL SYSTEM
7.3.1 Parallel System start-up
Verify on all Units, with open front door: Switches Q1 and Q2 must be open (Pos. O).
1. Connect the Utility power on all UPS’s.
(In case of separate inputs for Rectifier and Bypass, connect both).
• Power supply starts up. Indicated with flashing alarm and buzzer sounds.
• LED’s as indicated will be lit.
• Press mute, to reset alarm and buzzer.
First operated unit
All other units of the system
2. Close Q1 (Pos. I) on all Units.
• When closing Q1 on the last unit of the parallel system, the Bypass of all Units
connects to the Load.
• Rectifiers start automatically, blinking LED indicates Soft-start.
• At the end of Rectifier Soft-start, the LED remains lit.
• LED’s service check turn OFF.
First operated unit
All other units of the system
3. Connect the Battery to all Units by closing the external Battery Switches or Fuses, in
case of External Battery.
Continue ►
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 52/82
Operating Manual SG Series 100 – 120 - 150 kVA
4. Press “inverter on” ( I ) key on first unit.
• Soft-start of Inverter, indicated with blinking LED.
• At the end of Soft-start the LED Inverter remains lit.
• In case of sufficient output power, the output will transfer to Inverter.
• UPS output LED indicates Load on Inverter and the LCD must display on the main
screen the status “LOAD ON INVERTER”.
First operated unit
All other units of the system
5. Press “inverter on” ( I ) key on all other units.
(Do not start the next Inverter until the sequence of the previous ends)
• As soon as the output power of the Inverters is sufficient to supply the Load, the output
of the units with running Inverter will transfer to Inverter.
• All LED’s Inverter, Load on Inverter and Load supplied are ON.
First operated unit
All other units of the system
The LCD must display on the main screen on all Units the status “LOAD ON INVERTER”.
END OF PROCEDURE
NOTE !
The Battery must be charged for at least 10 hours, in order to ensure the full
backup runtime in the case of a Utility Failure.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 53/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.3.2 Maintenance system shutdown (Load supplied from Q2 on all Units)
Initial status: Load supplied from all Inverters.
First operated unit
All other units of the system
1. Press “inverter off” ( O ) key on all Units, and hold until the LED inside the Inverter symbol
turns OFF.
At no redundancy, the system will transfer to Utility supply.
First operated unit
All other units of the system
2. Close Q2 (Pos. I) on all Units.
Load is now supplied from Utility in parallel from Bypass and Manual Bypass Q2 of all Units.
First operated unit
All other units of the system
3. Open Q1 (Pos. O) and then press “total off” button on all Units.
The Bypass of all Units will disconnect and all Rectifiers are shutdown.
First operated unit
All other units of the system
4. Disconnect the Battery, in case of External Battery, from all Units.
• Wait 5 minutes for DC-Link Capacitors discharge.
First operated unit
All other units of the system
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 54/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.3.3 From Manual Bypass (Q2) to normal function VFI
Initial status: Load supplied from Manual Bypass.
All Q2 of the system are closed.
First operated unit
All other units of the system
1. Close Q1 (Pos. I) on all Units.
The Rectifiers will start automatically and at the closure of Q1 of the last Unit, the Bypass
of all Units will be activated.
First operated unit
All other units of the system
2. Connect the Battery to all Units by closing the external Battery Switches or Fuses, in
case of External Battery.
3. Open Q2 (Pos. O) on all Units.
First operated unit
All other units of the system
Continue ►
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 55/82
Operating Manual SG Series 100 – 120 - 150 kVA
4. Press “inverter on” ( I ) key on first unit.
• Soft-start of Inverter, indicated with blinking LED.
• At the end of Soft-start the LED Inverter remains lit.
• In case of sufficient output power, the output will transfer to Inverter.
• UPS output LED indicates Load on Inverter and the LCD must display on the main
screen the status “LOAD ON INVERTER”.
First operated unit
All other units of the system
5. Press “inverter on” ( I ) key on all other units.
(Do not start the next Inverter until the sequence of the previous ends).
• As soon as the output power of the Inverters is sufficient to supply the Load, the output
of the units with running Inverter will transfer to Inverter.
• All LED’s Inverter, Load on Inverter and Load supplied are ON.
First operated unit
All other units of the system
The LCD must display on the main screen on all Units the status “LOAD ON INVERTER”.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 56/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.3.4 Separate a Unit from the parallel system (System Redundancy)
Initial status: Load supplied from all Inverters.
First operated unit
All other units of the system
1. Press and hold “inverter off” ( O ) key on the Unit to separate, until the LED turns OFF.
Load supplied from Inverter(s) of the other Unit(s) of the parallel system.
First operated unit
All other units of the system
2. Open Q1 (Pos. O) and, only when the LED service check is ON, press “total off” button
on the Unit to separate.
First operated unit
All other units of the system
3. Disconnect the Battery, in case of External Battery, from the Unit to separate.
• Wait 5 minutes for DC-Link Capacitors discharge.
4. Disconnect the Utility supply from the separated Unit.
First operated unit
All other units of the system
END OF PROCEDURE
NOTE !
For any further intervention could nearest Service Center.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 57/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.3.5 Reconnect a Unit to a parallel system
1. Connect the Utility supply on the separated Unit.
• Press mute, to reset alarm and buzzer.
First operated unit
All other units of the system
2. Close Q1 (Pos. I) on the separated Unit.
Rectifier starts automatically.
First operated unit
All other units of the system
3. Connect the Battery, in case of External Battery, to the UPS on the separated Unit by
closing the external Battery Switch or Fuses.
4. Press “inverter on” ( I ) key on the separated Unit.
After Soft-start of the Inverter, the Inverter connects automatically to the other Units of
the parallel system.
• The LCD must display on the main screen the status “LOAD ON INVERTER”.
First operated unit
All other units of the system
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 58/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.3.6 Parallel system shutdown (No Load supply)
NOTE !
The Load must be disconnected.
Initial status: Load supplied from all Inverters.
First operated unit
All other units of the system
1. Press “total off” button on any one on the Units.
• Load is disconnected from UPS.
• Rectifier and Inverter are shut down and all output and input Contactors will be
opened.
• LED’s, Rectifier, Inverter and Load are OFF.
First operated unit
All other units of the system
2. Open Q1 (Pos. O) on all Units.
First operated unit
All other units of the system
Continue ►
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 59/82
Operating Manual SG Series 100 – 120 - 150 kVA
3. Disconnect the Battery, in case of External Battery, from all Units.
• Wait 5 minutes for DC-Link Capacitors discharge.
First operated unit
All other units of the system
4. Disconnect the Utility supply from all Units.
• All LED’s are OFF.
First operated unit
All other units of the system
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 60/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.3.7 Restore to normal operation after “total off”
View of the panel after pressing the button “total off”.
• All Contacts are open.
• Rectifier, Inverter and Static-Switch shutdown.
First operated unit
All other units of the system
1. Reset “total off” by pressing and holding the “total off” button and then the “inverter on”
( I ) key, on any of the Units simultaneously, until Load is supplied from Bypass and the
Rectifiers start.
• System output connects to Bypass Utility.
• Rectifiers start with blinking LED.
• At the end of Soft-start the LED’s remains lit.
• The LCD screen on all Units shows “LOAD ON BYPASS”.
First operated unit
All other units of the system
2. Connect the Battery to all Units by closing the external Battery Switches or Fuses, in
case of External Battery.
Continue ►
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 61/82
Operating Manual SG Series 100 – 120 - 150 kVA
3 Press “inverter on” ( I ) key on first unit.
•
•
•
•
Soft-start of Inverter, indicated with blinking LED.
At the end of Soft-start the LED Inverter remains lit.
In case of sufficient output power, the output will transfer to Inverter.
UPS output LED indicates Load on Inverter and the LCD must display on the main
screen the status “LOAD ON INVERTER”.
First operated unit
All other units of the system
4. Press “inverter on” ( I ) key on all other units.
(Do not start the next Inverter until the sequence of the previous ends)
• As soon as the output power of the Inverters is sufficient to supply the Load, the output
of the units with running Inverter will transfer to Inverter.
• All LED’s Inverter, Load on Inverter and Load supplied are ON.
First operated unit
All other units of the system
The LCD must display on the main screen on all Units the status “LOAD ON INVERTER””.
End of procedure
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 62/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.3.8 Restore to normal operation after EPO (Emergency Power Off)
UPS panel after activation of EPO
(Emergency Power Off) with Utility not
available, i.e. complete shutdown of the
UPS and LCD screen OFF.
In this case wait until Utility is again
available, then proceed to restart the UPS
as described below Points 1 through 3.
UPS panel after activation of EPO (Emergency Power Off) with Utility available.
All Contacts are open. Rectifier, Inverter and Static-Switch shutdown.
First operated unit
All other units of the system
1. Reset the EPO (Emergency Power Off) button.
• Press mute, to reset alarm and buzzer.
First operated unit
All other units of the system
2. Press “inverter off” ( O ) key on all Units.
• Rectifiers start with blinking LED.
• After pressing the “inverter off” key on the last unit of the parallel system, the output of
all Units connect to Bypass Utility.
• The LCD screen shows: “LOAD ON BYPASS”.
First operated unit
All other units of the system
Continue ►
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 63/82
Operating Manual SG Series 100 – 120 - 150 kVA
3. Connect the Battery to all Units by closing the external Battery Switches or Fuses, in
case of External Battery.
4. Press “inverter on” ( I ) key on first Unit.
• Soft-start of Inverter, indicated with blinking LED.
• At the end of Soft-start the LED Inverter remains lit.
• In case of sufficient output power, the output will transfer to Inverter.
• UPS output LED indicates Load on Inverter and the LCD must display on the main
screen the status “LOAD ON INVERTER”.
First operated unit
All other units of the system
5. Press “inverter on” ( I ) key on all other Units.
(Do not start the next Inverter until the sequence of the previous ends).
• As soon as the output power of the Inverters is sufficient to supply the Load, the output
of the units with running Inverter will transfer to Inverter.
• All LED’s Inverter, Load on Inverter and Load supplied are ON.
First operated unit
All other units of the system
The LCD must display on the main screen on all Units the status “LOAD ON INVERTER”.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 64/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.4 PROCEDURES FOR PARALLEL SYSTEM WITH COMMON BATTERY
7.4.1 Parallel System start-up
Verify on all Units, with open front door: Switches Q1 and Q2 must be open (Pos. O).
1. Connect the Utility power on all UPS’s.
(In case of separate inputs for Rectifier and Bypass, connect both).
• Power supply starts up. Indicated with flashing alarm and buzzer sounds.
• LED’s as indicated will be lit.
• Press mute, to reset alarm and buzzer.
First operated unit
All other units of the system
2. Connect the Battery to all Units by closing the external Battery Switch(es) or Fuses.
3. Close Q1 (Pos. I) on all Units.
• Rectifiers start automatically, blinking LED indicates Soft-start.
• At the end of Rectifier Soft-start, the LED remains lit.
• When closing Q1 on the last Unit of the parallel system, the Bypass of all Units
connects to the Load.
• LED’s service check turn OFF.
First operated unit
All other units of the system
Continue ►
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 65/82
Operating Manual SG Series 100 – 120 - 150 kVA
4. Press “inverter on” ( I ) key on first unit.
• Soft-start of Inverter, indicated with blinking LED.
• At the end of Soft-start the LED Inverter remains lit.
• In case of sufficient output power, the output will transfer to Inverter.
• UPS output LED indicates Load on Inverter and the LCD must display on the main
screen the status “LOAD ON INVERTER”.
First operated unit
All other units of the system
5. Press “inverter on” ( I ) key on all other units.
(Do not start the next Inverter until the sequence of the previous ends)
• As soon as the output power of the Inverters is sufficient to supply the Load, the output
of the units with running Inverter will transfer to Inverter.
• All LED’s Inverter, Load on Inverter and Load supplied are ON.
First operated unit
All other units of the system
The LCD must display on the main screen on all Units the status “LOAD ON INVERTER”.
END OF PROCEDURE
NOTE !
The Battery must be charged for at least 10 hours, in order to ensure the full
backup runtime in the case of a Utility Failure.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 66/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.4.2 Maintenance system shutdown (Load supplied from Q2 on all Units)
Initial status: Load supplied from all Inverters.
First operated unit
All other units of the system
1. Press and hold “inverter off” ( O ) key on all Units, until the LED inside the Inverter symbol
turns OFF.
At no redundancy, the system will transfer to Utility supply.
First operated unit
All other units of the system
2. Close Q2 (Pos. I) on all Units.
Load is now supplied from Utility in parallel from Bypass and Manual Bypass Q2 of all Units.
First operated unit
All other units of the system
3. Open Q1 (Pos. O) and press “total off” button on all Units.
The Bypass of all Units will disconnect and all Rectifiers are shutdown.
First operated unit
All other units of the system
4. Disconnect the Battery from all Units.
• Wait 5 minutes for DC-Link Capacitors discharge.
First operated unit
All other units of the system
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 67/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.4.3 From Manual Bypass (Q2) to normal function VFI
Initial status: Load supplied from Manual Bypass.
All Q2 of the system closed.
First operated unit
All other units of the system
1. Connect the Battery to all Units by closing the external Battery Switch(es) or Fuses.
2. Close Q1 (Pos. I) on all Units.
The Rectifiers will start automatically and at the closure of Q1 of the last Unit, the Bypass
of all Units will be activated.
First operated unit
All other units of the system
3. Open Q2 (Pos. O) on all Units.
First operated unit
All other units of the system
Continue ►
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 68/82
Operating Manual SG Series 100 – 120 - 150 kVA
4. Press “inverter on” ( I ) key on first unit.
• Soft-start of Inverter, indicated with blinking LED.
• At the end of Soft-start the LED Inverter remains lit.
• In case of sufficient output power, the output will transfer to Inverter.
• UPS output LED indicates Load on Inverter and the LCD must display on the main
screen the status “LOAD ON INVERTER”.
First operated unit
All other units of the system
5. Press “inverter on” ( I ) key on all other units.
(Do not start the next Inverter until the sequence of the previous ends)
• As soon as the output power of the Inverters is sufficient to supply the Load, the output
of the units with running Inverter will transfer to Inverter.
• All LED’s Inverter, Load on Inverter and Load supplied are ON.
First operated unit
All other units of the system
The LCD must display on the main screen on all Units the status “LOAD ON INVERTER”.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 69/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.4.4 Separate a Unit from the parallel system (System Redundancy)
Initial status: Load supplied from all Inverters.
First operated unit
All other units of the system
1. Press and hold “inverter off” ( O ) key on the Unit, to separate, until the LED turns OFF.
Load supplied from Inverter(s) of the other Unit(s) of the parallel system.
First operated unit
All other units of the system
2. Open Q1 (Pos. O) and, only when the LED service check is ON, press “total off” button
on the Unit to separate.
First operated unit
All other units of the system
3. Disconnect the Battery from the Unit to separate.
• Wait 5 minutes for DC-Link Capacitors discharge.
4. Disconnect the Utility supply from separated Unit.
First operated unit
All other units of the system
END OF PROCEDURE
NOTE !
For any further intervention could nearest Service Center.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 70/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.4.5 Reconnect a Unit to a parallel system
1. Connect the Utility supply on the separated Unit.
• Press mute, to reset alarm and buzzer.
First operated unit
All other units of the system
2. Connect the Battery to the UPS separated by closing the external Battery Switch or
Fuses.
3. Close Q1 (Pos. I) on the separated Unit.
Rectifier starts automatically.
First operated unit
All other units of the system
4. Press “inverter on” ( I ) key on the separated Unit.
After Soft-start of the Inverter, the Inverter connects automatically to the other Units of
the parallel system.
First operated unit
All other units of the system
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 71/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.4.6 Parallel system shutdown (No Load supply)
NOTE !
The Load must be disconnected.
Initial status: Load supplied from all Inverters.
First operated unit
All other units of the system
1. Press “total off” button on any one on the units.
• Load is disconnected from UPS.
• Rectifier and Inverter are shut down and all output and input contactors will be opened.
• LED’s, Rectifier, Inverter and Load are OFF.
First operated unit
All other units of the system
2. Open Q1 (Pos. O) on all Units.
First operated unit
All other units of the system
Continue ►
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 72/82
Operating Manual SG Series 100 – 120 - 150 kVA
3. Disconnect the Battery from all Units.
• Wait 5 minutes for DC-Link Capacitors discharge.
First operated unit
All other units of the system
4. Disconnect the Utility supply from all Units.
• All LED’s are OFF.
First operated unit
All other units of the system
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 73/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.4.7 Restore to normal operation after “total off”
View of the panel after pressing the button “total off”.
• All Contacts are open.
• Rectifier, Inverter and Static-Switch shutdown.
First operated unit
All other units of the system
1. Reset “total off” by pressing and holding the “total off” button and then the “inverter
on” ( I ) key, on any of the Units simultaneously, until Load is supplied from Bypass and
the Rectifiers start.
• System output connects to Bypass Utility.
• Rectifiers start with blinking LED.
• At the end of Soft-start the LED’s remains lit.
• The LCD screen on all Units shows: “LOAD ON BYPASS”.
First operated unit
All other units of the system
2. Connect the Battery to all Units by closing the external Battery Switch(es) or Fuses.
Continue ►
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 74/82
Operating Manual SG Series 100 – 120 - 150 kVA
3. Press “inverter on” ( I ) key on first unit.
• Soft-start of Inverter, indicated with blinking LED.
• At the end of Soft-start the LED Inverter remains lit.
• In case of sufficient output power, the output will transfer to Inverter.
• UPS output LED indicates Load on Inverter and the LCD must display on the main
screen the status “LOAD ON INVERTER”.
First operated unit
All other units of the system
4. Press “inverter on” ( I ) key on all other units.
(Do not start the next Inverter until the sequence of the previous ends)
• As soon as the output power of the Inverters is sufficient to supply the Load, the
output of the units with running Inverter will transfer to Inverter.
• All LED’s Inverter, Load on Inverter and Load supplied are ON.
First operated unit
All other units of the system
The LCD must display on the main screen on all Units the status “LOAD ON INVERTER”.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 75/82
Operating Manual SG Series 100 – 120 - 150 kVA
7.4.8 Restore to normal operation after EPO (Emergency Power Off)
UPS panel after activation of EPO
(Emergency Power Off) with Utility not
available, i.e. complete shutdown of the
UPS and LCD screen OFF.
In this case wait until Utility is again
available, then proceed to restart the UPS
as described below Points 1 through 3.
UPS panel after activation of EPO (Emergency Power Off) with Utility available.
All Contacts are open. Rectifier, Inverter and Static-Switch shutdown.
First operated unit
All other units of the system
1. Reset the EPO (Emergency Power Off) button.
• Press mute, to reset alarm and buzzer.
First operated unit
All other units of the system
2. Connect the Battery to all Units by closing the external Battery Switch(es) or Fuses.
3. Press “inverter off” ( O ) key on all Units.
• Rectifiers start with blinking LED.
• After pressing the “inverter off” key on the last unit of the parallel system, the output
of all Units connect to Bypass Utility.
• The LCD screen shows: “LOAD ON BYPASS”.
First operated unit
All other units of the system
Continue ►
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 76/82
Operating Manual SG Series 100 – 120 - 150 kVA
4. Press “inverter on” ( I ) key on first Unit.
• Soft-start of Inverter, indicated with blinking LED.
• At the end of Soft-start the LED Inverter remains lit.
• In case of sufficient output power, the output will transfer to Inverter.
• UPS output LED indicates Load on Inverter and the LCD must display on the main
screen the status “LOAD ON INVERTER”.
First operated unit
All other units of the system
5. Press “inverter on” ( I ) key on all other Units.
(Do not start the next Inverter until the sequence of the previous ends).
• As soon as the output power of the Inverters is sufficient to supply the Load, the
output of the units with running Inverter will transfer to Inverter.
• All LED’s Inverter, Load on Inverter and Load supplied are ON.
First operated unit
All other units of the system
The LCD must display on the main screen on all Units the status “LOAD ON INVERTER”.
END OF PROCEDURE
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 77/82
Operating Manual SG Series 100 – 120 - 150 kVA
8
OPTIONS
8.1 COMMUNICATION OPTIONS
Advanced SNMP Card
Simple Network Management Protocol
The Advanced SNMP Card is an interface to the Ethernet Network,
and provides UPS information via the standard SNMP Protocol
(UPS-MIB (RFC-1628); GE Single MIB; GE Parallel MIB).
The UPS can therefore be managed by a Network Management
System (NMS) or by our applications (for instance JUMP), which
uses this information to determine the state of the UPS in order to
guarantee safe and orderly shutdown of the server, when
needed.
IRIS Service
Internet Remote Information System
Internet Remote Information System for UPS System.
JUMP Software Suite
Java Universal Management Protocol
Software application for the control and monitoring of the UPS.
SGT5000_OPT_RMS_01
Remote Signalling Box (RSB)
Stop
Alarm
g
Mute
Test
Equipped with mimic diagram, general alarm, stop operation,
alarm reset and lamp.
GE Digital Energy
8.2 OPTIONS IN UPS CABINET
RPA Kit
Redundant Parallel Architecture
Up to 8 units parallel possible for redundancy or capacity in RPA
configuration.
5th harmonic filter
Located inside UPS cabinet.
FCC Filter
Located inside UPS cabinet. Meets FCC Class A, Part 15 Standard
for EMI suppression.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 78/82
Operating Manual SG Series 100 – 120 - 150 kVA
8.3 CONNECTION FOR OPTIONS
WARNING !
The installation and cabling of the options must be performed by QUALIFIED
SERVICE PERSONNEL only.
Make sure that the UPS installation is completely powered down.
Refer to the “Safety prescriptions - Installation” described on Section 1.
8.3.1 Remote Signalling Box (RSB)
The optional Remote Signalling Box allows monitoring of the operation of the UPS, using the potential free contacts
fitted on the “P4 - Customer Interface Board“ of the UPS.
It can be used by simply putting the box on a desktop or on a wall or, removing the box, it can be surface
mounted.
The remote panel contains an internal buzzer and the following status indicators:
• Mimic diagram With LEDs indicating the operation of Rectifier and Inverter, and the power source supplying
the critical Load.
• Alarm
Indicating a critical situation on the UPS (LED light and audible alarm).
• Stop
Indicating the UPS is preparing to shut down in a short time.
• Mute
Push button, resets the buzzer.
• Test
Push button checks all the LEDs and the buzzer of the remote panel.
The cable connecting the RSB to the UPS cabinet must be min. 16 wires / 0.25mm2.
The plug B is included in the delivery of the option RSB (cable connecting UPS with RSB not included). Maximal
allowable length: 985 ft (300 m).
It must be wired at one end with a D - female plug- 25 pin (J2 – P4 Customer Interface Board).
NOTE !
The alarms on free potential contacts can be connected on terminals X1 instead J2 (see
correlation X1 – J2 in Section 4.1 of the Installation Guide).
Pink + Red
1
max 985ft / 300m
1
2
3
4
X4
A
P4 - IM0005
Customer Interface
77 3 in
m
m
49
50
55
56
COMMON ALLARM
AUX. BUZZER
STOP OPERATION
16
17
19
20
22
23
X3
Stop
Alarm
g
P.S.: The above mentioned colors are
suitables only for XY standard cable
Mute
Test
SGT5000_
white/green
brown/green
white/yellow
yellow/brown
J2
OPT_010150_RMS
_01US
grey/pink
blue/red
4
1
LOAD ON MAINS
B PLUG
SUB D - MALE
3
9
black
violet
37
38
40
42
43
LOAD ON INVERTER
44
XA
TERMINALS BLOCK
J2
2
1
green
yellow
IM6544
X15
Grey + Blue
1
5 1/4" in
130mm
blue
grey
UTILITY FAILURE
white
brown
1
2
31
32
33
34
14
B-
24V
GND
2
1 2
J2 - SUB D - MALE
red
pink
REMOTE
SIGNALLING
BOX
1 2 3 4 5 6 7 8 9 10 11
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
12 13 14 15 16 17 18 19 20 21 22
XA
TERMINALS
BLOCK
XA
A
pink
red
grey
blue
GE Digital Energy
8 1/2" in
216mm
Fig. 8.3.1-1 Remote Signalling Box connection
A
B
XA
Terminals X3, X4 and X15 fitted inside the Remote Signalling Box.
Plug J2 (sub D - male - 25 pin) must be connected to the connector J2 (sub D - female-25 pin) located
on “P4 - Customer Interface Board“.
Terminals block XA for 24 VDC supply Remote Signalling Box.
NOTE !
If the remote signal panel is plugged on connector J2, the terminal blocks X1 cannot be used to
drive an external alarms monitoring device, because it is supplied by the internal UPS low
voltage power supply.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 79/82
Operating Manual SG Series 100 – 120 - 150 kVA
9
MAINTENANCE
WARNING !
All maintenance and service works must be performed by QUALIFIED SERVICE
PERSONNEL.
9.1
MAINTENANCE
A UPS system, like other electrical equipment, needs periodic preventive maintenance.
A regular maintenance check of your installation guarantees higher reliability of your safe critical power
supply.
Preventive maintenance work on the UPS can be done only by trained Service technicians.
We therefore recommend you sign a Maintenance and Service contract with GE Global Services @ 1800-637-1738
9.1.1 Service check
If this lamp lights up during the normal operation, that means that the unit has not been serviced for the
last 20,000 hours by a GE trained technician.
We highly recommend that you contact your Service Centre for preventive maintenance work.
9.1.2 Fans and ventilation
We recommend a periodic cleaning of the ventilation channels and grids on the UPS system, in order to
guarantee proper air circulation in the unit and in the Battery.
We recommend replacement of the fans in the units every 20,000 hours.
9.1.3 Other components with limited lifetime
We recommend the replacement of components such as Filter Capacitors and Lithium Battery for the
backup of data on the control boards of the units every 50,000 hours.
9.1.4 Battery
We recommend a periodic Manual Battery Test, especially if the Automatic Battery Test is disabled, in
order to verify if the Battery can provide the expected backup time in case of Utility Failure.
We recommend this test be performed at least every 3 months, especially if the Battery is not
sufficiently discharged during normal operation.
The discharge time you use should be at least half of the Battery runtime.
For Automatic Battery Test setting, a special code is required to enter user set-up parameters.
The start up technician has access to this code and can program this feature during start up.
Please consider that, if you did a full Battery Test to verify the full runtime of the Battery, the charger
needs at least 8 hours to recharge the Battery up to 90% of its capacity.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 80/82
Operating Manual SG Series 100 – 120 - 150 kVA
9.1.5 Long shut-down periods of the UPS-system
To guarantee that the Battery is fully charged, the UPS system should be in operation for at least 12
hours every 3 months.
If not the Battery may be permanently damaged.
9.1.6 UPS room conditions and temperature
The UPS room and the Battery Room have to be maintained clean and free from dust.
A high temperature of the UPS room and of the Battery Room affect the lifetime of several components
inside the equipment.
The Battery is very sensitive to room temperatures above 77°F (25°C).
9.1.7 Long shut-down periods of the UPS-system
a)
Cleaning, a visual inspection and a mechanical inspection of the UPS modules.
b)
Replacement of defective parts or the preventive replacement of parts with a defined lifetime
c)
“Updating” of the equipment (technical improvements subsequent to the delivery).
d)
Check the calibration of DC voltage and Inverter Output Voltage and Frequency.
e)
Check of the settings of the electronic regulation, the control and the alarm circuits of the
Rectifier(s) and Inverter(s).
f)
Functional checks on Thyristors, Diodes, Transformers, Filter Components, e.g. to ensure that they
are operating within the specified design parameters.
g)
Overall performance test including a Utility Failure simulation with and without the Load.
h)
Monitoring Battery operation in discharge and recharge mode including any boost charge duties.
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Page 81/82
Operating Manual SG Series 100 – 120 - 150 kVA
10 NOTES
10.1 NOTES FORM
It is recommended to note in this section Notes, with date and short description all the operations
performed on the UPS, as: maintenance, components replacement, abnormal situations, etc.
Date
Modifications reserved
OPM_SGS_USM_M10_M15_0US_V030.doc
Description
Done by
Page 82/82
Operating Manual SG Series 100 – 120 - 150 kVA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement