VADDIO Extreme USB 2.0 Extender TX User guide

VADDIO Extreme USB 2.0 Extender TX User guide
Installation and User Guide
Vaddio™ Extreme USB 2.0 Extenders
Part Numbers:
999-1005-022 - North America
999-1005-122 - International
Extreme USB 2.0
Extender TX
Extreme USB 2.0
Extender RX
© 2013 Vaddio - All Rights Reserved. Extreme USB 2.0 Extenders, Document Number 342-0468 Rev D
Extreme USB 2.0 Extenders
Table of Contents
Overview .................................................................................................................................................................... 3
Intended Use: ......................................................................................................................................................... 3
Important Safeguards: ........................................................................................................................................... 3
Save These Instructions: ....................................................................................................................................... 3
Unpacking .................................................................................................................................................................. 4
Extreme USB Extenders (North America) 999-1005-022 ...................................................................................... 4
Extreme USB Extenders (International) 999-1005-122 ......................................................................................... 4
Requirements: ........................................................................................................................................................ 4
Anatomy of the Extreme USB 2.0 Extenders ............................................................................................................ 5
Image: Front Panel Extreme USB 2.0 TX Unit .................................................................................................. 5
Image: Rear Panel Extreme USB 2.0 TX ........................................................................................................... 5
Image: Front Panel of Extreme USB 2.0 RX Unit ............................................................................................. 6
Image: Rear Panel of Extreme USB RX Unit .................................................................................................... 6
Installation Instructions .............................................................................................................................................. 7
Checking out the Installation: ................................................................................................................................. 7
Diagram: Basic Connectivity of the Extreme USB 2.0 Extenders ..................................................................... 8
Troubleshooting ......................................................................................................................................................... 9
Specifications:.......................................................................................................................................................... 12
Compliance and CE Declaration of Conformity: ...................................................................................................... 13
Warranty Information ............................................................................................................................................... 14
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 2 of 16
Extreme USB 2.0 Extenders
OVERVIEW
The Vaddio Extreme USB 2.0 Extenders
provide a complete working solution
powered by Extreme USB Long Reach
USB 2.0 enabled by the Lion’sGate™
USB 2.0 Extension ASIC. The system
has a transmit (TX) or remote device
side and a receive (RX) or Host PC side
and extends USB 2.0 high speed and
USB 1.1 devices up to 100m (328.1’)
over Cat-5e or better cable.
Extreme USB 2.0 Extenders - RX (left) and TX (right)
The TX side has the USB Type-A female USB 2.0 port and is located with the device and powered with the 5
VDC power supply while the RX side is port powered by the Host PC. Power is not required on the RX Host side
for normal operation.
The Extenders operate with USB 2.0 high-speed host controllers and USB 1.1 classic hosts. All USB device
types are supported including Control, Interrupt, Bulk and Isochronous at up to 480Mbp/s. The Extenders are true
plug and play and ready to operate out of the box and no new driver installation is required (bonus).
The Extreme USB 2.0 Extenders support all major operation systems including Windows®, Mac OS® and Linux®
and are ideal for a wide variety of fine USB devices like Vaddio HD-USB Camera, AV Bridge, Quick-Connect™
USB and EasyTalk™ Wireless USB Mic System as well as printers, scanners, and game controllers.
Intended Use:
Before operating the device, please read the entire manual thoroughly. The system was designed, built and
tested for use indoors, and with the provided power supply and cabling. The use of a power supply other than the
one provided or outdoor operation has not been tested and could damage the device and/or create a potentially
unsafe operating condition.
Important Safeguards:
Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged.
In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock,
do not immerse in water or other liquids and avoid extremely humid conditions. Do not connect Ethernet or
Power over Ethernet (PoE) cables directly to the RJ-45 ports on the device as damage may result.
Use only the power supply provided with the system. Use of any unauthorized
power supply will void any and all warranties.
Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not work
well for professional installations and can be the cause of intermittent connections which can result in
the data and/or control line failing and locking up. For best results please use standard RJ-45
connectors and test all cables for proper pin-outs prior to use.
Save These Instructions:
The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from
www.vaddio.com free of charge.
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 3 of 16
Extreme USB 2.0 Extenders
UNPACKING
All the components within the shipping box are packaged as described in the sections below. Carefully remove all
parts included in the packaging.
Extreme USB Extenders (North America) 999-1005-022
Unpack and identify the following parts
 One (1) Extreme USB Extender TX
 One (1) Extreme USB Extender RX
 One (1) 5 VDC Switching Power Supply
 One (1) North American Power Cord
 One (1) 6’ (1.83m) USB 2.0 Cable Type-A Male to Type-B Male
 One (1) 1’ (305mm) USB 2.0 Cable Type-A Male to Type-B Male
 Documentation
Extreme USB Extenders (International) 999-1005-122
Unpack and identify the following parts
 One (1) Extreme USB Extender TX
 One (1) Extreme USB Extender RX
 One (1) 5 VDC Switching Power Supply
 One (1) Euro Power Cord
 One (1) UK Power Cord
 One (1) 6’ (1.83m) USB 2.0 Cable Type-A Male to Type-B Male
 One (1) 1’ (305mm) USB 2.0 Cable Type-A Male to Type-B Male
 Documentation
Requirements:
To complete the installation, you will also require the following items that are not included with the product:

One (1) USB 2.0 compatible PC (host computer) with a USB compliant operating system. The PC must have
the ability to supply 5VDC, 500ma of power or an additional power supply may be required.

Cat-5e Unshielded Twisted Pair (UTP) cable or better with two RJ45 connectors. For best results please use
standard RJ-45 connectors, mark and test all cables for proper pin-outs prior to use.
All references to Cat-5e cable in this document represent the minimum requirement of solid core Cat-5e
unshielded twisted pair cable or better. Cat -6 and STP cables can be substituted. Regular Cat-5 cable can be
used; however the maximum length may not be achievable.
Note: Not all equipment is compatible with the Extreme USB 2.0 Extenders. For whatever reason,
some stuff just doesn’t work. The Extreme USB 2.0 Extenders do comply with the USB 1.1 and USB
2.0 specifications, but there are a number of factors that can affect the operation of USB devices over
distance.
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 4 of 16
Extreme USB 2.0 Extenders
ANATOMY OF THE EXTREME USB 2.0 EXTENDERS
Image: Front Panel Extreme USB 2.0 TX Unit
The TX unit provides USB Type-A port for standard USB devices. The TX unit is powered by an external AC
adapter or the Vaddio HD-USB PTZ camera in the WallVIEW HD-USB PRO kit.
➍
➊
➋
➎
➌
➏
1) USB Device Port (USB Type-A): Accepts USB device.
2) Device LED (Green/Orange): Indicates when a USB device is connected to the Device Port.
a. Will illuminate solid green when device is plugged in and active.
b. Off when device is in suspend mode or TX unit is powered off.
c. Orange when the TX unit detects an overcurrent condition and the attached USB device attempts to
draw more than the 500mA current.
3) Power LED (Vaddio Blue): LED turns blue when power is supplied and goes OFF when no power is
available.
4) Link LED (Green): Indicates a valid Extreme USB link is established between the RX and TX over Cat-5e
cabling. LED turns on when link between RX and TX is established. Off when there is no link between RX
and TX.
5) Host LED (Green): Indicates that the system is properly enumerated on the host PC. LED blinks when in
suspend state.
6) Activity LED (Amber): Indicates activity when data transmission is active between TX and RX. LED blinks
intermittently with or without a USB device connected. The LED is off when in suspend mode.
Image: Rear Panel Extreme USB 2.0 TX
➐
➑
➒
7) Earth Ground: Optional Earth Ground connection to housing of unit. Accepts an M2 screw.
8) Power Port: Connects to the AC power supply. Required at TX for proper operation.
9) Link Port (RJ-45): Accepts an RJ-45 connector for Cat-5e cabling (or better).
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 5 of 16
Extreme USB 2.0 Extenders
Image: Front Panel of Extreme USB 2.0 RX Unit
The RX unit connects to the computer using a standard Type-A male to Type-B male USB 2.0 cable. Power for
the RX Unit is provided by the USB port on the Host computer.
➋
➊
➌
➍
1) Power LED (Vaddio Blue): LED turns blue when power is supplied and goes OFF when no power is
available.
2) Link LED (Green): Indicates a valid Extreme USB link is established between the RX and TX over Cat-5e
cabling. LED turns on when link between RX and TX is established. Off when there is no link between RX
and TX.
3) Host LED (Green): Indicates that the system is properly enumerated on the host PC. LED blinks when in
suspend state.
4) Activity LED (Amber): Indicates activity when data transmission is active between TX and RX. LED blinks
intermittently with or without a USB device connected. When the TX and RX are in suspend mode, the LED
is off.
Image: Rear Panel of Extreme USB RX Unit
➎
➏
➐
➑
5) Earth Ground: Optional Earth Ground connection to housing of unit. Accepts an M2 screw.
6) Power Port (optional): Power supply not required in normal operation. USB Port is required to deliver 500mA
to the RX unit. Please avoid the use of inexpensive USB hubs.
7) USB Type-B Port: Used to connect the RX to the host computer. Power is supplied to the RX on this port.
8) Link Port (RJ-45): Accepts RJ-45 connector for Cat-5e cabling (or better).
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 6 of 16
Extreme USB 2.0 Extenders
INSTALLATION INSTRUCTIONS
Step 1: Before installing the Extreme USB 2.0 Extenders:
A. Determine where the computer is going to be located.
B. Determine the location of the USB device or USB camera.
C. To ensure proper operation it is recommended that only Cat-5e or better (Unshielded Twisted Pair - UTP)
cabling is used to connect between the RX unit to the TX unit. The cabling must have a straight-through
conductor configuration (568B) with no crossovers and must be terminated with 8P8C RJ-45 connectors at
both ends. The combined length of any patch cords using stranded conductors must not exceed 33’ (10m).
Please make every effort to minimize the use of stranded Cat-5e patch cables between the extenders.
Step 2: Place the RX unit near the host computer and install the supplied 6’ (1.83m) USB 2.0 cable between the
RX unit and the USB port on the host computer. The USB port must supply 5 VDC, 500mA to the RX unit. If the
computer cannot supply the proper power levels to the RX host unit, then another %V power supply must be
used.
Step 3: Place the TX unit near the USB device in the desired remote location and install the supplied 1’ (305mm)
USB 2.0 cable into the TX unit and the USB Device. For the USB signal, please use the USB 2.0 cables only.
Step 4: Plug the 5VDC power supply into a suitable electrical outlet and connect the supply to the TX unit.
Step 5: Connect the Cat-5e cabling (not included) into the RJ-45 Link port on the TX unit.
Step 6: Plug the other end of the Cat-5e cable into the RJ-45 Link port on the RX unit.
Checking out the Installation:
A. On the RX and TX units, check that the Power, Host, and Link LEDs are on and that the Activity LED is
blinking. If the Link LED is permanently off, then the cabling between the RX and TX unit is not installed
properly or is defective.
B. For Windows users (2000, XP, Vista, Windows 7), open Device Manager to confirm that the “Generic USB
Hub” has been installed.
C. For Mac OS X users, open the System Profiler to confirm that the “Hub” has installed correctly. In the left
hand column under Hardware, select “USB” and inspect the right hand panel. If the system has been
installed correctly, you should find it listed as a “Hub” under the USB High-Speed Bus/USB Bus.

Operating System Notes:
To open System Profiler in OS X: Open the Finder, select Applications, then open the Utilities folder and
double click on the System Profiler icon.
To open Device Manager in Windows 2000 or XP: Right click “My Computer” then select: Properties >>
Hardware tab >> Device Manager.
To open Device Manager in Windows Vista or Windows 7:
Open the Start menu, right click on “Computer” then select: Manage >> Device Manager.
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 7 of 16
Extreme USB 2.0 Extenders
Diagram: Basic Connectivity of the Extreme USB 2.0 Extenders
Vaddio HD-USB PTZ Camera with local power for the camera and the Extreme USB 2.0 TX unit are shown. A Cat-5e cable run from the
TX extender (remote side) to the RX extender located at the Host PC to extend USB 2.0 video up to 100m (328.1’). Use the supplied 1’
(305mm) USB 2.0 cable at the camera side USB port and the provided 6’ (1.83m) at the PC side USB host port. Cat-5e patch cords are
typically use stranded pairs and can stop working on the High Speed USB 2.0 Signal at over 10’ (3.04m).
Local Power
5 VDC
12 VDC
USB 2.0 over Cat-5e
Cable (solid core)
Up to 100m (328.1’)
(Not supplied)
Extreme USB
2.0 TX Unit
(Remote)
Supplied 1’ (305mm) USB
2.0 Cable to the USB 2.0
port on the camera
Vaddio ClearVIEW™ HD-USB PTZ
Camera or other USB 2.0 Device
Extreme USB
2.0 RX Unit
(Host)
Supplied 6’ (1.83m)
USB 2.0 Cable
Large Format Flat Screen Monitor
USB 2.0 Video
using UVC Drivers
5VDC, 500ma
supplied by PC
over USB 2.0 port
HD Video
Host PC with
UC Soft Client
Software
Simulated Video Images of TCF “The Bank” Stadium (MPLS, MN)
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 8 of 16
Extreme USB 2.0 Extenders
TROUBLESHOOTING
The following table provides troubleshooting tips. The topics are arranged in the order in which they should be
executed in most situations. If you are unable to resolve the problem after following these instructions, please contact
technical support for further assistance.
Problem
Probable Cause
All LEDs on the RX unit
(PC-Host side) are off.
The RX unit is not receiving enough
power from the USB port.
Solution Possibilities
1) Ensure the USB connection between the
RX unit and the host PC is properly
installed. Remember to use a USB 2.0
rated cable with USB 2.0 signals.
2) Move the USB connector to another USB
port on the host PC. Some PCs have
internal hubs and adequate power may
not be available on every port.
All LEDs on the TX unit
(device side) are off.
The TX unit is not receiving power
for the AC Adapter.
1) Ensure that the AC power adapter is
properly connected to the TX unit.
2) Check the viability of the AC electrical
outlet. Check that the TX unit’s power
LED comes on when plugged into a
working outlet.
Link LEDs on the TX
and RX units are off.
The is no connection between the
TX and RX units
1) Check the Cat-5e connection and the
cable. Avoid using the pull-through or EZ
type RJ-45 connectors. Check the pinouts and use 568B straight through
standard.
2) Connect a short and known good patch
cable between the TX and RX units. If it
works, then there is a Cat-5 cabling
problem.
Link LED on RX unit is on
but the Host LED on RX
unit is off.
 The host computer is not powered
on.
 The LEX unit is not connected to
the computer (when used with the
optional LEX AC adapter).
 The computer does not support
USB hubs.
 The USB Ranger® 2201 is
malfunctioning.
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
1) Disconnect all USB devices from the TX
unit.
2) Disconnect the RX unit from the computer.
3)
Disconnect the TX unit from the AC power
adapter.
4) Reconnect the RX unit to the computer.
5) Reconnect the TX unit to the AC power
adapter.
6) In the Universal Serial Bus controllers
section of Device Manager, check that the
RX unit is recognized as a “Generic USB
Hub”.
Page 9 of 16
Extreme USB 2.0 Extenders
Troubleshooting (continued)
Problem
Probable Cause
The Extreme USB
Extenders were
working, but then the
Host LED on the TX
and RX units are all of a
sudden blinking. Now
what?
The TX unit is in suspend/standby
mode. The PC operating system
may have put the Extreme USB 2.0
Extenders into a standby state, or
no USB devices are attached to the
TX unit.
All LEDs on both the
RX unit and the TX unit
are on, but the USB
device does not operate
correctly or is detected
as an unknown device
in the operating system.
 The USB device may be
malfunctioning.
1) Disconnect the Extreme USB 2.0
Extenders from the computer.
 The computer does not
recognize the USB device.
2) Connect the USB device directly to the USB
port on the computer.
 The application software for the
device is not operating properly.
3) If the device does not operate properly,
consult the user documentation for the
device.
 The Extreme USB 2.0
Extenders are malfunctioning
Solution Possibilities
1) Recover/Resume the operating system
from standby mode (see the PC’s
operating system documentation).
2) Attach a USB device to the system.
4) Update your system BIOS, chipset, or USB
Host controller drivers from your
System/Mother- board manufacturer’s
website.
5) If the device operates properly when directly
connected to the computer, connect another
device (of a different type) to the USB
Ranger® 2201. Connect the USB Ranger®
2201 to the computer.
6) If the second device does not operate, the
USB Ranger® 2201 may be malfunctioning.
Contact technical support for assistance.
7) If the second device does operate properly,
the first device may not be compatible with
the USB Ranger® 2201.
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 10 of 16
Extreme USB 2.0 Extenders
Troubleshooting (continued)
Problem
USB device is attached
to TX unit’s USB port but
TX device LED is off.
Probable Cause
A USB device must have the
appropriate driver installed on the
computer operating system. Or
must us UVC (universal video
class) drivers.
Solution Possibilities
1) Install the required USB device driver on the
computer operating system prior to attaching
the USB device to the TX unit. Please see
the USB device manufacturer’s website for
details.
2) Consult your USB device documentation
and power the USB device with the
additional USB device manufacturer
supplied power supply (if available).
Device LED is orange
and units are no longer
functioning.
Overcurrent condition has occurred
because USB device draws more
power than can be supplied per USB
specification (500mA).
Power cycle TX Unit.
Host and LINK LEDs on
RX / TX units blink
intermittently.
There is a possibility that the TX and
RX units don’t have the same
firmware revision.
Use a different TX / RX pair that has the same
firmware revision.
Upgrade the TX /RX firmware, contact technical
support for assistance.
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 11 of 16
Extreme USB 2.0 Extenders
SPECIFICATIONS:
Extreme USB 2.0 Extenders
Part Numbers
Range
USB device support
USB host support
AC adapter(s)
AC adapter connector
Current available to USB
device at RX unit
RX unit USB connector
TX unit Link connector
TX unit Link connector
TX unit USB connector
RX unit dimensions
TX unit dimensions
TX power consumption
RX power consumption
System shipping weight
Operating temperature range
Storage temperature range
Operating humidity
Storage humidity
Regulatory testing
ESD rating
999-1005-022 North America
999-1005-122 International
100m (330ft) over Cat-5e (or better) cable
High-speed devices (480 Mb/s) (USB 2.0) Full speed devices (12 Mb/s) (USB 2.0
& 1.1) Low speed devices (1.5 Mb/s)
EHCI (USB 2.0) and OHCI/UHCI (USB 1.1)
Input: 100/240 V AC, 50 – 60 Hz, 600 mA maximum
Output: 5 VDC, 3 A
1.7 mm center-positive jack
500 mA
1 x USB Type-B
1 x RJ45
1 x RJ45
1 x USB Type-A
3.94” x 2.99” x 1.02” (100 mm x 76 mm x 26 mm)
3.94” x 2.99” x 1.02” (100 mm x 76 mm x 26 mm)
500 mA maximum
Approx. 500 mA (No Load). 1.5A (Full load)
2.0 lbs. (0.9 kg)
0°C to 50°C
-20°C to 70°C
20% to 80% relative humidity, non-condensing
10% to 90% relative humidity, non-condensing
FCC (Class B), IC (Class B), CE (Class B)
EMC EN-61000-4-2 8kV Contact, 16kV Air
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 12 of 16
Extreme USB 2.0 Extenders
COMPLIANCE AND CE DECLARATION OF CONFORMITY:
Extreme USB 2.0 Extenders
Compliance testing was performed to the following regulations:
 FCC Part 15, Subpart B
 ICES-003 ISSUE 4, 2004
 EN55022 A1 2007
 IEC 60950-1:2005 (2nd Edition); Am 1:2009
 EN 60950-1:2006+A11:2009+A1:2010+A12:2011



Class B
Class B
Class B
Class A
Class A
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15, Subpart B, of the FCC Rules
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This
device must accept any interference including interference that may cause undesired operation of the device.
ICES-003 Compliance
ICES-003, Issue 4: 2004
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numeriques de la classe B préscrites dans le Règlement sur le brouillage radioélectrique édicte par le
ministère des Communications du Canada.
European Compliance
This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions and
Immunity and meets the requirements for a Class A digital device. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate measures.
Standard(s) To Which Conformity Is Declared:
European Standard EMC EN-55022:2006+A1:2007 Class B
EN 61000-3-2:2006
EN 61000-3-3:2003
EN55024:1998 + A2:2003
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 13 of 16
Extreme USB 2.0 Extenders
WARRANTY INFORMATION: (See Vaddio Warranty, Service and Return Policies posted on vaddio.com for complete details):
Hardware* Warranty: One year limited warranty on all parts. Vaddio warrants this product against defects in materials and
workmanship for a period of one year from the day of purchase from Vaddio. If Vaddio receives notice of such defects during
the warranty period, they will, at their option, repair or replace products that prove to be defective. Please see Vaddio’s
Service Terms and Conditions at vaddio.com for specific details and policies.
Exclusions: The above warranty shall not apply to defects resulting from: improper or inadequate maintenance by the
customer, customer applied software or interfacing, unauthorized modifications or misuse, operation outside the normal
environmental specifications for the product, use of the incorrect power supply, improper installation (plugging things in
wrong), improper extension of the power supply cable or improper site operation and maintenance.
Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the unit is under
warranty and is found to be defective. If the product is out of warranty, Vaddio will test then repair the product or products. The
cost of parts and labor charge will be estimated by a technician and confirmed by the customer prior to repair. All components
must be returned for testing as a complete unit. Vaddio will not accept responsibility for shipment after it has left the premises.
Vaddio will only advance replace out of box failures or random equipment failures up to 30 days after the purchase date (not
the install date).
Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria for repair costs
and/or replacement. Vaddio Technical Support can be contacted through one of the following resources: e-mail support at
[email protected] or online at www.vaddio.com.
Return Material Authorization (RMA) Number: Before returning a product for repair or replacement, request an RMA from
Vaddio’s technical support. Provide a technician with a return phone number, e-mail address, shipping address, and product
serial numbers and describe the reason for repairs or returns as well as the date of purchase and proof of purchase. Include
your assigned RMA number in all correspondence with Vaddio. Write your assigned RMA number on the clearly on the
shipping label when returning the product. All products returned for credit are subject to a restocking charge without
exception.
Voided Warranty: The warranty does not apply if the original serial number has been removed or if the product has been
disassembled or damaged through misuse, accident, modifications, or unauthorized repair. Cutting the power supply cable on
the secondary side (low voltage side) to extend the power to the device voids the warranty for that device.
Shipping and Handling: Vaddio will not pay for inbound shipping transportation or insurance charges or accept any
responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, transportation, and
insurance charges for all items under warranty but will not assume responsibility for loss and/or damage by the outbound
freight carrier. If the return shipment appears damaged, retain the original boxes and packing material for inspection
by the carrier. Contact your carrier immediately.
Products Not Under Warranty: Payment arrangements are required before outbound shipment for all out of warranty
products.
*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry standard practices.
Other General Information:
Care and Cleaning
Do not attempt to take this product apart at any time. There are no user-serviceable components inside.

Do not spill liquids in the product

Keep this device away from food and liquid

For smears or smudges on the product, wipe with a clean, soft cloth

Use a lens cleaner on the lens, but this doesn’t have a lens, so don’t

Do not use any abrasive chemicals.
Operating and Storage Conditions:
Do not store or operate the device under the following conditions:

Temperatures above 40°C (104°F) or temperatures below 0°C (32°F)

High humidity, condensing or wet environments

In swimming pools or wading ponds

In inclement weather

Dry environments with an excess of static discharge

Under severe vibration
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 14 of 16
Extreme USB 2.0 Extenders
Inside Back Cover - Blank
Extreme USB 2.0 Extenders - Document Number 342-0468 Rev D
Page 15 of 16
Extreme USB 2.0 Extenders
Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464
www.vaddio.com
©2012
Vaddio
All Extenders
Rights Reserved.
Reproduction
in wholeRev
or inD part without written permission is prohibited. Specifications
pricing
Extreme
USB- 2.0
- Document
Number 342-0468
Pageand
16 of
16 are
subject to change without notice. Vaddio, Quick-Connect, EasyTalk and ClearVIEW are trademarks of Vaddio. All other trademarks are property
of their respective owners. Document 342-0468 Rev. D
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement