WisyCom MTK952 User manual

WisyCom MTK952 User manual
MPR30-IEM User Manual
High performance
True diversity
Receiver
SN: ________________
Rev. 06 (ref. FW v1.6)
Date: 18 July 2014
MPR30-IEM User Manual
1
Rev. 06
MPR30-IEM User Manual
Rev. 06
BRIEF DESCRIPTION
MPR30 is a compact true diversity receiver designed for professional in-ear monitoring
applications. This receiver features a real TRUE DIVERSITY configuration along with a unique
wideband tuning range up to 232 MHz. Audio processing can be Stereo MPX or mono based.
The output audio stage is especially design to have maximum audio peak-dynamic of 200 mW.
MPR30-IEM is designed to be:

“easy & quick to use” thanks to
o
automatic setup functions (i.e. frequencies, scan for best channels),
o
remote configuration utilities (thru infrared or micro-USB interface) using
Wisycom MPR30 RX Manager application
o

OLED display with intuitive context menu navigation
“extremely flexible”, with an incredible frequency agility up to 232MHz

o
MPR30-IEM-N: 470/700 MHz (TV ch 21/49)
o
MPR30-IEM-M:566/798 MHz (TV ch 33/61)
“best in class performances”, thanks to the latest Wisycom technology the unit has
extreme RF sensitivity and immunity and superb audio quality
“a durable & upgradable investment”, thanks to the very robust design (aluminium
housing) and the possibility to upgrade/enhance units performances.

Above a schematic with an overview of main receiver functions.
2
MPR30-IEM User Manual
Rev. 06
SAFETY INSTRUCTION











Read this safety instruction and the manual first
Follow all instructions and information.
Do not lose this manual.
Do not use this apparatus under the rain or near the water.
Do not install the apparatus near heaters or in hot environments, do not use outside the
operating temperature range.
Do not open the apparatus, only qualified service technician are enabled to operate on it.
The apparatus needs servicing when it is not properly working or is damaged by liquids,
moisture or other objects are fallen in the apparatus.
Use only accessories or replacement parts authorized or specified by the manufacturer.
Clean the apparatus only with dry cloths, do not use liquids.
Report the serial number and the purchasing date in front of the manual. It is needed to
have proper replacement parts or accessories from the manufacturer.
When replacement parts are needed, use only replacement parts authorized from the
manufacturer. Substitution with not authorized parts could result in electric shock,
hazards or fire.
Keep attention on all the labels with warnings or hazards on the apparatus.
The apparatus is intended for professional use; anyway the manufacturer alerts the
user that the headphone output power of the apparatus could exceed the level of 85 dB(A) of
sound pressure level and this could be dangerous for the hearings. Do not use the headphone
with high power level or for long time. Reduce the power or suspend the hearing in case of any
kind of hearing problem.
3
MPR30-IEM User Manual
Rev. 06
BATTERIES
MPR30-IEM works with standard camera battery:
2xIEC-LR6 1.5 size-AA alkaline or NiMh rechargeable
KLIC 8000 (lithium-ion, rechargeable)
Ricoh DB-50 (lithium-ion, rechargeable)
DR9708 Duracell (lithium-ion, rechargeable)
Battery status can be checked on OLED display or looking the status of LED indicator ON.
Lithium-ion battery can be charged through
A. dedicated charger
B.
integrated micro-usb-B connector
For B item, the charging status can be checked looking the status of LED indicator ON.
The receiver can be used also during the batteries charging with lithium
rechargeable batteries inside.
Don’t use the receiver without batteries . The receiver powered thru micro-USB without
batteries doesn't work correctly.
DO NOT operate the device with some new and some old batteries. Always replace
ALL BATTERIES.
Remember to remove the batteries when the device is not in use.
4
MPR30-IEM User Manual
Rev. 06
PRODUCT OVERVIEW
Upper Panel
ON LED indicator
Headphone Output
On/Off/Volume
control
SMA connector Antenna B
SMA connector Antenna A
SMA antenna Connector A and B
MPR30-IEM is supplied with two couple of antennas. According to the working band, different
antenna models can be supply. All the models have
Antenna Code label
black cap and a black label with code in white colour.
For more details see the section Accessories and Parts
Headphone Output
The audio headphone output with 3.5 mm stereo jack socket lockable (TRS).
Audio level can be adjusted with the Volume control knob and the Audio settings> Pwr. Limit
menu.
Maximum output power: 2x150mW @ 32Ω, [email protected]Ω
Pin Assignment: Tip = left (hot), Ring = right (hot), Sleeve = Gnd
On/Off/Volume control
The control knob in the upper panel allows:




To switch the receiver ON: turn the control knob volume control clockwise until it clicks
To switch the receiver OFF: turn the control knob volume control counter clockwise until it
clicks
To adjust the volume: turn the control knob volume control until the volume set has the
desired level.
To disable the lock volume: turn off and turn on the receiver within 1 second.
NOTE: turn off and turn on the receiver

within 1 secondMPR30 restarts without the initialization phase

after 1 second MPR30 restarts with complete initialization
5
MPR30-IEM User Manual
Rev. 06
Front panel
MPR30-IEM allows an easy and quick configuration using buttons, RGB LED’s and an OLED
display.
ON Led Indicator
SCAN/DOWN
Button
MENU/SELECT
Button
RF Led Indicator
SYNC/UP
MENU/EXIT
Button
Infrared Interface
(IR)
OLED Display
The receiver has a high contrast display. Pushing one of the 4 buttons while the receiver is
active (but the display is off), turn on automatically the display. After a time-out user setting
(see Display>Off timeout menu) the display turns off automatically.
SEL & EXIT Buttons
Push the 2 buttons together to enter on the function menu
SEL Button
Push this button to navigate function menu’s and keep pushing to save the chosen setup
EXIT Button
Push this button to turn off the display.
During menu navigation push this button to exit from current menu (escape function).
SYNC/UP Button
Push and keep this button to start a synchronisation with a Wisycom transmitter (follow
instructions on display). Before starting synchronization IRDA must be enabled on Wisycom
transmitter.
During menu navigation push this button to move -up and select the previous item.
SCAN/DOWN Button
Push and keep this button to start the automatic scan.
During menu navigation push this button to move-down and select the previous item
6
MPR30-IEM User Manual
Rev. 06
charging status
battery status
Tuning phase
power up
ON & RF Led Indicators (Firmware rel. v0.2)
ON
red
RF
off
red
off/on
red
off/on
fixed
green
off
fixed
green
blue
after the tuning phase, a stereo
signal is received
fixed
green
green
after the tuning phase, a mono
signal is received
fixed
green
slow
blinking
green
fast
blinking
green
red
blinking
blue
blinking
green
fixed
green
white
on/off
the batteries charge of the
receiver is good (>25% lifetime)
the batteries charge of the
receiver is low (<25% lifetime)
on/off
on/off
WHEN
when the receiver is power on,
during the power up phase
when the receiver is power on,
after the power up phase
when the receiver is power on,
during a frequency change
phase (see Gr-Ch or Frequency
menu)
after the tuning phase, no
transmitter is received
off
off
the batteries charge of the
receiver is very low (<12%
lifetime)
battery error
during batteries charging
off
during batteries charging
off
during batteries charging
green/
blue
device in bootloader mode*
MEANING
the receiver is not ready to use,
wait the status display on display
the PLL is not locked on the select
frequency, wait for lock ( about
1second or less)
the PLL is not locked on the select
frequency, wait for lock
the receiver is locked on the
select frequency, the batteries
charge is good, no transmitter is
synchronized with the receiver,
no output audio available
the transmitter is correctly tuned,
the bars in the status display
show the RF levels received from
antenna A and B
the transmitter is correctly tuned,
the bars in the status display
show the RF levels received from
antenna A and B, in the status
display M symbol appears upper
the battery level
the batteries charge of the
receiver is good
change or put on charge the
batteries as soon as possible
change or put on charge the
batteries immediately
change the batteries
the batteries are charging (<90%
of complete charge)
the batteries are charging (≥90%
of charge reached)
charge complete
* to put the MPR30-IEM in boot mode: power on the device push and keep both UP and DOWN buttons
for few seconds (until the led indicators light up, then release the buttons)
7
MPR30-IEM User Manual
Rev. 06
PUTTING THE DIVERSITY RECEIVER INTO OPERATION




Insert the batteries
Connect the headphones
Connect the 2 antennas on the SMA connectors
Turn the knob control clockwise until it clicks and verify on the display the Antenna
model to use (if the connected antennas on the receiver is different from the
antenna model indicate on the display, power off the receiver and replace them with
the proper model of antennas)
after the power up phase, the Status display is showed on the OLED display
verify the setting and eventually adjust the settings using the Operating Menu


Status display
- Receiver Name (ex. MPR30-IEM RX)
- Group (ex. Gr:00) and Channel (ex. Ch:01)
- Frequency (ex. Fr:697.000 MHz)
- Squelch (ex. Sq:12dBuV)
- Mode (ex. Stereo)
CSquelch level
A B C
A.
B.
RF Level Antenna A and B (range 5 ÷ 70 dBµV)
Between the two RF bars there is a dotted line where the first 3 dots indicate
6/8/10dBµV and the other 15 dots indicate the rest of the range (from 14 to 70dBµV
with step of 4dBµV
An orizzontal sign in a central row shows the setted Squelch level
C.
deviation level (range of 54 dB, bar with 3dB steps; upper level= 0dB, under level =-54dB)
the upper symbol:
indicates presence of audio output
S
T
indicates absence of audio output (RF level < Squelch)
indicate absence of audio output (no pilot tone detected)
NOTE: in case of absence of pilot tone and RF level < Squelch, the symbol
display
D.
batteries level for MPR30-IEM receiver
the upper symbol:
indicates receiving of a mono signal
M
S
8
indicates receiving of a stereo signal
will be
MPR30-IEM User Manual
DISPLAY MENU
Audio
Settings
Out mode
Stereo/Mono/Mix
Balance
Vol. boost
L|R
Low (-12÷+12)
Hi (-12÷+12)
-12÷+12dB
Output load
32Ω/16Ω
Pwr limit
OFF/100mW/50mW/30mW
Equalizer
Gr-Ch
Frequency
Edit RX
Squelch
Scan
Rev. 06
GR (0÷39)
CH (0÷59)
N: 470.000÷700.000
M: 566.000÷798.000
*Only using lithium battery
OFF*-0/3/6/9/12/15/18/21/24//28/32/36/40/46 dBµV
Channel
GR 00 - 39
Groups
more groups (max 10)
Scan now
freq. Min/ freq. Max/
Squelch scan
Freq
step (100 or 200 kHz)
Scan BTN
Channel/Groups/Freq
View last
Deploy
Name
MENU
Quick Menu
Settings
Display
Infrared
LED
Sync
Advanced
Lock volume
Pilot Squelch
Model
Range
470÷700
Serial
Battery
S2334437
Version
BL
App
Version
Option
3.71 Volt
Errors
0
Restore
1/2/3/4/5/6/Factory
Save
1/2/3/4/5/6
FW
HW
Preset
9
0÷5
5÷60 steps 5
10÷120 steps 10 - OFF
Yes/No
Yes/No
Add
Load
Delete
Delete all
MPR30-IEM
Clone
Info
12 characters
ex. RECEIVER-123
Bal /Mix ; Clone ; Off
Contrast
Low timeout (sec)
Off timeout (sec)
Full/Alarm/OFF
00÷23
default/0/...
00÷23
It appears if
exist at least
1 clone
v1.5
v1.4d
v1.54d
6
N
Clone parameters
Preset parameters
MPR30-IEM User Manual
Rev. 06
From Status Display push SEL and EXIT together to enter on the
Main menu
Use UP/DOWN to navigate on all available menus
Push SEL to select a menu item
Use UP/DOWN to move on the different parameters of the menu
Push SEL to modify the parameter menu
Use UP/DOWN to change the parameter value
Keep push SEL to save changing
Push EXIT to return on the Main Menu
Push EXIT to return on the Status display
Audio settings
The Audio settings menu allows to configure the audio output.
PARAMETER
SETTING
MEANING
The left and right signals are available as usual. The Balance
Stereo
setting serves to adjust the balance between the left and
right stereo signal.
The left-right signals are mixed and are available as a mono
Mono
signal in both headphone channels. It is not possible to
Out mode
adjust the level of the 2 channels as in Out mode Mix.
The left-right signals are mixed and are available as a mono
signal in both headphone channels.
Mix
The Mix mode setting serves to adjust the relative levels of
the two separate channels in the mixer mono signal.
This menu allows to of adjusting the gain of low and high
frequency components (bass and treble) within the audio
signal.
Low and High
Equalizer
1. Push UP/DOWN button to increase/decrease the
frequencies
gain of the Low frequencies (50Hz)
-12dB/+12dB
2. Push SEL button to shift on High frequencies,
1dB steps
3. Push UP/DOWN button to increase/decrease the
gain of the High frequencies (10kHz)
4. Keep push SEL button to SAVE
This menu allows to increase or decrease the volume of the
output headphones, selectable from -12 dB to 12 dB. Set the
-12/-6/0/3/6/9/12dB
Vol. boost
appropriate volume boost and then adjust the volume with
the control knob.
Set the Output load according to the impendence of the
16Ω/32Ω
Output load
headphones connected
This menu allows to limit the power output. If set to
OFF (only using lithium
Pwr limit
OFF(only lithium battery), there is no power limit control. If
battery) / 100mW /
set to OFF using alkaline or NiMH batteries, the receiver set
50mW / 30mW
automatically the max value permitted (100mW)
NOTE: When the volume knob is rotated, appears a screen with a
volume bar and the values of Pwr limit, Outpul load and Vol. boost
10
MPR30-IEM User Manual
Rev. 06
Edit RX
The Edit RX menu allows to configure the radio frequency settings.
PARAMETER
Gr-Ch
Frequency
Squelch
SETTING
0÷39 groups
0÷59 channels
470÷700 MHz
for MPR30-IEM-N
566÷798 MHz
for MPR30-IEM-M
OFF or
0/3/6/9/12/
15/18/21/
24/28/32/
36/40/46dBuV
MEANING
Select current group and channel. Group name and
channel frequency are displayed on the right.
If the specific group/channel is not locked, the frequency
can be edited in this menu.
This menu allows to disable the RF squelch or to setup the
desired squelch level in dBuV (note 0 dBuV is equal to 107 dBm).
It allows making three types of scan over a desired
channel, group or frequency. MPR30-IEM manages up to
2400 custom frequencies organized in 40 groups of 60
channels each. This extreme flexibility makes the scan
function very flexible.
This function can be called also using the dedicated
DOWN&SEL buttons pushed together.
“Squelch scan” indicates the threshold below which a
channel is considered as free or almost free.
Scan
“Scan BTN” is the parameter to set the rapid function
called pressing DOWN&SEL buttons together.
It’s possible to set Channel, Group or Frequency scan.
“View last” allows to see the result of the last scan
operation.
“Deploy” allows to send to a MTK952 the last scan.
From the transmitter it’s possible to see the graphic of the
last scan and choose the frequency to tune.
(*)As per Wisycom standard, group 00 and group 01 or 09 are special; respectively the “center
frequency” (474,482/… MHz) and the intergap frequency (i.e. 470/478/486/… MHz). A scan on group
00 will reveal in few seconds the overall DVB-T occupation on the area, while a scan on group 01 will
give possible working frequency, usable also in presence of strong DVB-T signal (sort to speak working
in the band-guard of 2 digital television channels).
11
MPR30-IEM User Manual
Rev. 06
“Scan now” menu
The following table lists the three types of scans that can be performed
Once started a Channel scan operation the receiver asks for
group to be used*. Press and hold the SEL button to select the
group to scan.
Then it prompts to turn off all transmitters.
So press SEL to start the scan!
Channel
After few seconds, scan results are displayed sorted by level,
making easier to pick up the best one.
The dotted line in the graph indicate the squelch threshold.
Under the graph are reported the following parameters:
Ch: Channel
Rank: Ranking position
Freq: Frequency
Lev: RF level
Pushing simultaneously UP and DOWN button, the results can
be also displayed on a chart in ascending order according to
the number of the channel.
After the selection of the desired channel, a screen appears
with the selected frequency, channel and group and it is
possible to Set or Synchronize the receiver with the
transmitter. We recommend setting the frequency and then
synchronize it with the transmitter.
If the scan is done on Groups, you can choose a maximum of
10 groups from among the 40 groups shown in the table
(Press the SEL button to select and press it again to deselect).
In the upper left shows the number of the selected group and
the number of selected groups, while in the upper right corner
there is the item "START" to start the scan.
Groups
To select START, go to the box 39 and press the "UP" button or
go to the box 0 and press the "DOWN" button, so press SEL to
run the scansion.
Then it prompts to turn off all transmitters.
So press SEL to start the scan!
12
MPR30-IEM User Manual
Rev. 06
After few seconds, scan results are displayed on a histogram.
Each column of the histogram is divided into two parts by a
black line. The lower part indicates the number of free
channels (RF level < Squelch level - 6dBµV) in the group, while
the upper one the number of channels almost free
(Squelch level < RF level < Squelch level - 6dBµV).
We recommend to choose the group with the highest number
of free channels.
Press SEL to select the desiderate group and choose the
channel as in “Channel scan”
After the selection of the desired channel, a screen appears
with the selected frequency, channel and group and it is
possible to Set or Synchronize the receiver with the
transmitter. We recommend setting the frequency and then
synchronize it with the transmitter.
The Frequency scan allows to select a range of frequency to
scan, between a maximum and a minimum value and the step
with which to perform the scans. Press and hold the SEL
button to confirm.
Then it prompts to turn off all transmitters.
So press SEL to start the scan!
Freq
After few seconds, scan results are displayed on a chart in
ascending order according to the frequency (step 1MHz). The
dotted line in the graph indicate the squelch threshold.
Pushing simultaneously UP and DOWN button it’s possible to
zoom the graph to show all the steps of scan
After the selection of the desired frequency, a screen appears
with the selected frequency and the RF level and it is possible
to Set or Synchronize the receiver with the transmitter. We
recommend setting the frequency and then synchronize it
with the transmitter.
13
MPR30-IEM User Manual
Rev. 06
Settings
The Settings menu allows to configure main settings of the device.
PARAMETER SETTING
MEANING
The name menu allows to change the name of the
receiver. This is the name displayed in the top of
the Status display and it is the name sent to the
12 case-sensitive alphanumeric transmitter with the sync function (for the
Name
characters
transmitter with this advanced capability).
Use the UP/DOWN buttons to change the selected
character and push SEL button to switch to the
next character.
The quick menu is displayed pushing UP or DOWN
buttons when the receiver is on the Status display.
Set to Bal/Mix to enter quickly to the Balance/Mix
mode menu (according to the Out mode
configured).
Quick
Bal/Mix ; Clone ; Off
Menu
Set to “Clone” to enter quickly to the Load clone
menu
Set to “Off” for disable this function (if is set “Off”
and UP or DOWN buttons are pushed, nothing
happens).
Contrast
0÷5
Change contrast display from 0 (min) to 5 (max).
Low timeout sets the timeout from 5 to 60 seconds
Low timeout 5÷60 (steps 5)
(5sec steps) to decrease the brightness display.
Display
Off timeout sets the timeout from 10 to 120
10÷120 (steps 10)
Off timeout
seconds in 10 sec. steps to turn off the display.
or OFF
With OFF setting the display never turns off.
3 LED setting are available:
Full
Full: LED indicators works normally;
Alarm
Alarm: LED indicators lights up only when an alarm
LED
OFF
happened;
OFF: LED indicators remain off.
Infrared
By this menu, MPR30-IEM can be connected to IRDA for setup or firmware upgrades.
When the Infrared interface is active, the following screen is displayed.
NOTE: while in this menu display is not automatically turned off.
14
MPR30-IEM User Manual
Rev. 06
Sync
The SYNC function is useful to tune a transmitter on the same
frequency of the receiver via the IR interface. Before starting the
sync function tune the receiver on desired channel, manually or
using the SCAN utility. After this, enable the IR interface on the
transmitter. Now press UP&EXIT buttons together or enter in the
Sync menu to start the SYNC function. Keep the IR window of the
transmitter in front of the IR window of the receiver and, as soon as the connection is done, the
receiver will send to the transmitter all the information needed.
If the operation is not possible, (i.e. the frequency range of the transmitter is not compatible with
the frequency of the receiver), the display will show an error message.
If the transmitter has the function “NAME” enabled, when the sync function is completed it will
show the same name of the synchronized receiver.
Advanced
The Advanced menu allows to manage advanced settings.
PARAMETER
SETTING
MEANING
If set to Yes, during the “max brightness” of the
display an open lock is displayed on the Status
Display. After the “Display -Low timeout” the lock
Yes / No
becomes closed and the lock volume is enabled.
Lock volume
To enable the volume setting it is necessary turn
the volume knob below the previous setting or
make a “quick turn off – turn on”.
When the Pilot tone is enabled, the audio output is
muted unless the correct carrier is detected
(19kHz).
Yes / No
When the Pilot tone is disable, the audio output is
Pilot Squelch
muted if RF level < Squelch level.
For the presence/absence of audio output, check
the upper symbol in the status display.
Add
00÷23
To add a clone
Load
Default/00÷23 To load a clone *
Clone *
Delete 00÷23
To delete a clone *
Delete all
To delete all the clones *
* A clone is a partial configuration of the MPR30-IEM which can be copied from a receiver to another
using the IRDA interface. It consists of the same parameters of pre-set configuration for less than
display, quick menu and headphones parameters (see the Operating menu for more details).
From firmware version v1.3 the MPR30-IEM is able to manage up to 24 clones (from 00 to 23). The
menus of the clone management allow to add/load and delete a clone.
* It appears if exist at least a1 clone
15
MPR30-IEM User Manual
Rev. 06
How to add a clone
Out mode
Balance
Equalizer
Vol boost
Pilot tone
Gr-Ch
Squelch
RX Name
Clone name
Enable the IRDA interface on the RX from
which take the configuration (Infrared menu)
Put the receivers face
to face
At the end of the process the name
of the clone will be identify with the
name of the receiver.
Enter in the Add menu and select the
wanted clone number. Then push SEL
to start the IRDA communication.
How to load a clone
Use Clone>Load menu or UP/DOWN button (if the quick menu is configured to clone) to load a
clone. Afterwards push the arrows to change clone, SEL to activeted the clone and EXIT to exit
without changing.
Ex.
The configuration saved before the loading of the clone is saved on
the clone named “default”, therefore loading the default “clone”
allows to return with the previous settings. The following
arrows displayed near the clone number indicates the currently
clone loaded.
16
MPR30-IEM User Manual
Rev. 06
Loading a clone, all the clone parameters are set on the receiver. The follow icon appears on the
right of the display indicating that a clone is loaded. The number and the name of the clone are
displayed on the top of the display menu and a brief list of the main parameters are displayed on the
status menu.
Name of the clone
Number of the clone
symbol to indicate that a
clone is loaded
is loaded
Main parameters
NOTE: the clones are saved on the EPROM and remains saved also after a reboot of the device.
NOTE: If a clone is loaded and then a reboot is executed, the MPR30-IEM always restarts with the
previous configuration (default clone).
NOTE: When a clone is loaded, it's not possible change the parameters
NOTE: When a clone with Power limit set to OFF is loaded on the receiver but the receiver isn’t
using Lithium battery, the power limit is set automatically to the max value permitted for no lithium
battery (that is 100mW).
Info
the INFO function shows many important features or information of MPR30-IEM receiver:
PARAMETER
Model
Range
Serial
FW
HW
Battery
Errors
MEANING
Wisycom receiver model
Frequencies range of working
Serial number
Version * Firmware version
BL
Bootloader version
App
Application version
Version
Hardware version
MPR30-IEM Options
Option
N= freq. range 470÷ 700 MHz,
M= freq. range 566÷ 798 MHz
Batteries voltage
Number of errors.
If the number of errors is > 0 push SEL button to enter on the
Errors list. For each error a brief description and the error code is
showed. For more information, please see the Error List section.
* The Firmware Version recaps BL (Bootloader Version) and App (Application version).
17
example
MPR30-IEM
470-700
S2334437
V1.6
V1.4d
V1.63d
6
N
3.71 Volt
4
MPR30-IEM User Manual
Rev. 06
Preset
This menu allows to load/save 6 user presets or load the Factory configuration.
PARAMETER
SETTING
Restore
1/2/3/4/5/6/Factory
Save
1/2/3/4/5/6
MEANING
Select the Restore submenu and chose the presets
to load: user presets or Factory preset. Push and
keep SEL button to load the preset.
Select the Save submenu and chose the user presets
to save. Push and keep SEL button to save the
preset
ERROR LIST
When an error occurs, the receiver
A. shows a message on the display
and for some error types
B. increases the errors counter in the info menu
C. inserts the error type and code on the error list in the info menu
When the error is solved, the message on the display disappear, but the error information
(code and description) are available on the error list in the Info menu (only for some error, see
the below table).
NOTE1: When the receiver is reset the error information (code and error type on the list) are
lost, with the exception of errors codes 87/88/89/8A.
NOTE2: To reset the error counter and the errors list, it is necessary to contact Wisycom.
HW init failed
Message on display
(A)
HW init failed
Battery Low
Battery Low
Battery charge failed
Battery charge failed
I2C communication error
Device ID copy1 invalid
Memory recovered
Device ID copy2 invalid
Memory recovered
RF copy1 invalid
Memory recovered
RF copy2 invalid
Memory recovered
PLL unlocked
I2C communication error
Device ID copy1 invalid
Memory recovered
Device ID copy2 invalid
Memory recovered
RF copy1 invalid
Memory recovered
RF copy2 invalid
Memory recovered
-
I2C access failed
04
Device ID copy 1
87
Device ID copy 2
88
RF mem copy 1
89
RF mem copy 2
8A
PLL unlocked
84
CH mem header
-
CH mem header
85
Param mem header
-
Param mem header
86
Errors
18
Error type
(C)
Code
(C)
MPR30-IEM User Manual
Rev. 06
TROUBLESHOOTING
Problem
Possible cause
“HW init failed” message
appears on the display
“Battery Low” message
appears on the display
“Battery charge failed”
message appears on the
display
“I2C communication error”
message appears on the
display
“Device ID copy1 invalid
Memory recovered”
message appears on the
display
“Device ID copy2 invalid
Memory recovered”
message appears on the
display
“RF copy1 invalid
Memory recovered”
message appears on the
display
“RF copy2 invalid
Memory recovered”
message appears on the
display
The Serial Number of the
receiver in the Info menu
is UNCAL
The errors 87 (Device ID
copy 1 ) and 88 (Device ID
copy 2) appear in the
errors list
The errors 89 (RF mem.
copy 1 ) and 8A (RF meme.
copy 2) appear in the
errors list
The receiver is not able to
tuned on the selected
frequency and the ON led
indicator remains red
19
Error during the hardware initialization
phase
Low level on the battery
Possible solution
-reset the receiver, if the
problem persists send to repair
at Wisycom Repair Centre
- change batteries or
- recharge the batteries
Error during batteries charger
(damage batteries or wrong batteries)
- change batteries
Communication error on bus I2C
- send to repair at Wisycom
Repair Centre
Error during the initialization phase. The
CRC-16 check of device data (copy 1)
detects error.
- nothing (the receiver
automatically replace the
corrupt copy1 with copy2)
Error during the initialization phase. The
CRC-16 check of device data (copy 2)
detects error.
- nothing (the receiver
automatically replace the
corrupt copy2 with copy1)
Error during the initialization phase. The
CRC-16 check of RF data (copy 1) detects
error.
- nothing (the receiver
automatically replace the
corrupt copy1 with copy2)
Error during the initialization phase. The
CRC-16 check of RF data (copy 2) detects
error.
- nothing (the receiver
automatically replace the
corrupt copy2 with copy1)
Error during the initialization phase. The
CRC-16 check of device data (copy 1 and
copy 2) detects error.
- send to repair at Wisycom
Repair Centre
Error during the initialization phase. The
CRC-16 check of device data (copy 1 and
copy 2) detects error.
- If the Serial Number in the
Info menu is UNCAL, then send
to repair at Wisycom Repair
Centre
- If the Serial Number in the
Info menu is not UNCAL,
continue to use the receiver
Error during the initialization phase. The
CRC-16 check of RF data (copy 1 and copy
2) detects error.
- contact Wisycom for more
information
Error during frequency tuning
- try to change the frequency, if
the problem persists send to
repair at Wisycom Repair
Centre
MPR30-IEM User Manual
The frequencies of all the
channels and groups is
equal to the lower
frequency of the receiver
Error in the channel memory during the
initialization phase.
(according to the receiver
470 MHz for MPR30-IEM-N
566 MHz for MPR30-IEM-M)
Configuration mismatch
Error in the parameter memory
Rev. 06
if the error code 85 appears on
the errors list:
- load a new frequency file
(wdf) in the frequency memory
of the receiver and
- contact Wisycom for more
information
if the error code 86 appears on
the error list:
- load a preset configuration
using Preset menu and
- contact Wisycom for more
information
If a problem not listed in the above table occurs or if the problem cannot solved with the
proposed troubleshooting, please contact support service at [email protected] or
[email protected]
20
MPR30-IEM User Manual
Rev. 06
ACCESSORIES AND PARTS
AWNL30
For MPR30-IEM-N
Band 470 ÷ 574 MHz
Antenna Code label 520
AWNH30
For MPR30-IEM-N
Band 574 ÷ 700 MHz
Antenna Code label 634
AWML30
For MPR30-IEM-M
Band 566 ÷ 654 MHz
Antenna Code label 590
AWMH30
For MPR30-IEM-M
Band 654 ÷ 798 MHz
Antenna Code label 725
Other accessories available:
CAUSBM1
Micro USB cable (to configure MPR30-IEM and to recharge
lithium battery)
UPK300E
Infrared programming kit
(interface + software) USB interface
MPRLBP
Lithium-ion battery pack
CS-KLIC8000 type
Rating: 3.7Vdc @1600mAh (5.9Wh)
MPRBAT
Battery charger
21
Antenna Code
label
MPR30-IEM User Manual
Rev. 06
HOW TO USE MPR30 RX MANAGER
Wisycom MPR30 RX Manager can be used to load or save the channels memory and upgrade
the firmware.
Instruction to connect MPR30 using UPK300 / UPK300E:
1.
2.
3.
4.
5.
6.
22
Connect to the PC the infrared programming interface (UPK300 or UPK300E) using a
USB cable (NOTE: it is not possible to use IR interface of MRK950 or MRK960)
Check if the version of ENG RX Manager installed in your PC is the latest version. If
not, uninstall the ENG RX Manager actives in your PC and install the new version
Run ENG RX Manager
Power up the receiver MPR30 and enable the IRDA interface:
a.
push
button,
b.
push
button until that Infrared submenu appears on the display
(Headphones>Edit RX>Display>Infrared)
c.
push again
button and check the display shows ‘IR IF active’
Put in contact MPR30 and UPK300/UPK300E
Push Disconnected button. On the Device connection windows select UPK port and
verify that upk300 is
selected on the
Silabs USB devices
panel. If upk300
device is not
showed, push
Refresh button
and/or try to
disconnect and
reconnect the USB
cable connected to
the UPK300. Then
click OK.
MPR30-IEM User Manual
7.
23
Rev. 06
If the connection is ended well, the Connected icon is showed on the top of the panel
and “Connected on USB by UPK” is displayed on the information panel
MPR30-IEM User Manual
Rev. 06
Instruction to connect MPR30 using USB cable:
In order to use the micro USB port to configure the
MPR30, it is necessary to install the MPR30 USB
driver (see How to install MPR30 USB driver)
1.
2.
3.
4.
5.
Connect the MPR30 to the PC through the
micro USB interface using the USB cable
Check if the version of ENG RX Manager
installed in your PC is the latest version. If
not, uninstall the ENG RX Manager actives
in your PC and install the new version
Run ENG RX Manager
Power up the receiver MPR30
Push Disconnected button. On the Device
connection windows select USB port
and verify that a COMx is selected on
the Virtual COM panel. If COMx is not
showed, push Refresh button and/or
try to disconnect and reconnect the
USB cable connected to the MPR30.
Then click OK.
6.
24
If the connection is ended
well, the Connected icon
is showed on the top of
the panel and “Connected
on COMx” is displayed on
the information panel
MPR30-IEM User Manual
Rev. 06
How to load/save channels memory
Write:
Push the button Write from WDF file… and select the wdf file to load on the MPR30.
Read and save:
Push the button Read and save to WDF file… , insert the .wdf file name and the path where to
save the wdf file.
During the process of writing/reading & saving, a green bar below the panel shows the
progress of the process and on the information panel it is possible to verify what the
application is doing.
To Modify the wdf file, it is possible to use the spreadsheet FREQUENCY 2010 v16.xls available
on the website:
- open the file and enable changes and macro
- load the wdf file clicking on READ WDF button
- execute the desiderate changes
- save the wdf file clicking on SAVE WDF button
The WDF thus modified can be used to write on the MPR30’s channels memory.
How to upgrade the firmware
Select FW upgrade panel
1. Push the Browse button and select the upk file
2. Put the receiver in bootloader
mode: power on the MPR30
keep pushing both the arrow
bottons). When the receiver is
in bootloader mode, all the led
in the front panel are turn on.
3. Click on Start button and check
the progress of the upgrade
process in the green bar
25
MPR30-IEM User Manual
Rev. 06
TECHNICAL SPECIFICATIONS
• Frequency ranges
• Switchable channels
• Switching-window
• Frequencies
• Frequency error
• Temperature range
• Modulation
• Peak deviation
• “A” / “B” antenna in
• Antenna input imp.
• Sensitivity
• Co-channel rejection
• Adjacent chan. Sel.
• Spurious rec. Rej.
• IF image rejection
• Intermod. rejection
• IIP3
• Spurious emissions
• Noise Reduction
• AF bandwidth
• Frequency response
• Distortion
• SND/D ratio
• Stereo separation
• Display
• Powering
• Weight
• Headphone-output
• Battery life
: MPR30-IEM-N option 470÷ 700 MHz
MPR30-IEM-M option 566 ÷ 798 MHz
other ranges are available on request in 470÷798 MHz
: 40 groups of 60 channels fully user programmable.
: up 232 MHz.
: microprocessor controlled frequency synthesizer circuit,
with 25 kHz minimum step. The frequencies can be easily
PC reprogrammed with the optional UPK 300E Programming Kit.
: < ± 2.5 ppm, in the rated temperature range.
: -10 ÷ +55 °C.
: FM, (19 kHz sync carrier)
: ±48 kHz
: with sturdy connectors.
: 50 ohm sma type (SWR < 1:2; typ. 1:1.4).
: 2 µV ( 6 dBµV), for SND/N > 52 dB;
in the whole switching-window [1].
: > 2.5 dB.
: > 80 dB typical (for channel spacing ≥ 400 kHz).
: > 100 dB.
: > 90 dB.
: > 76 dB.
: > +10 dBm typical.
: < 2 nW (typical = 0.1 pW).
: ENR (Wisycom Extended-NR)
: 30 Hz ÷ 15 kHz.
: ± 0.5 dB in the 30 Hz ÷ 15 kHz range.
: 0.3 % typical.
: 90 dB typical [1]
: > 60 dB
: Display OLED 128x64 (white)
: 2 x IEC-LR6 1.5V size-AA alkaline or rechargeable elements
: 100 g approx. without batteries
: Stereo Plug 3.5mm(TRS) Locking (M6 x 0.5 thread) with 2 X 150mW @ 32 Ohm
: approx.. 5 hours (alkaline batteries), 8 hours (lithium batteries)
NOTE [1]: RMS value, 22 Hz / 22 kHz, unweighted.
The MPR30-IEM receiver complies with ETSI specifications: ETS 300 422.
26
MPR30-IEM User Manual
MECHANICAL DRAWING
Note: unit is mm
27
Rev. 06
MPR30-IEM User Manual
28
Rev. 06
MPR30-IEM User Manual
Rev. 06
ITALY ONLY
Obblighi di informazione agli utilizzatori
Modello di informazioni agli utenti dei prodotti di tipo “professionale”
INFORMAZIONE AGLI UTENTI
ai sensi dell’art. 13 del Decreto Legislativo 25 luglio 2005, n. 151 “Attuazione delle Direttive 2002/95/CE,
2002/96/CE e 2003/108/CE, relative alla riduzione dell’uso di sostanze pericolose nelle apparecchiature
elettriche ed elettroniche, nonché allo smaltimento dei rifiuti”
Il simbolo del cassonetto barrato riportato sull’apparecchiatura o sulla
sua confezione indica che il prodotto alla fine della propria vita utile
deve essere raccolto separatamente dagli altri rifiuti.
La raccolta differenziata della presente apparecchiatura giunta a fine
vita e’ organizzata e gestita dal produttore. L’utente che vorrà disfarsi
della presente apparecchiatura dovrà quindi contattare il produttore e
seguire il sistema che questo ha adottato per consentire la raccolta
separata dell’apparecchiatura giunta a fine vita.
L’adeguata raccolta differenziata per l’avvio successivo
dell’apparecchiatura dismessa al riciclaggio, al trattamento e allo smaltimento ambientalmente
compatibile contribuisce ad evitare possibili effetti negativi sull’ambiente e sulla salute e favorisce il reimpiego e/o riciclo dei materiali di cui è composta l’apparecchiatura.
Lo smaltimento abusivo del prodotto da parte del detentore comporta l’applicazione delle sanzioni amministrative previste dalla normativa vigente.
29
MPR30-IEM User Manual
30
Rev. 06
MPR30-IEM User Manual
Wireless System Communications
Via Spin 156  I-36060 Romano d’Ezzelino  Italy
Tel. +39 -0424 -382605  Fax +39 - 0424 - 382733
www.wisycom.com  e-mail: [email protected]
31
Rev. 06
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement