Honeywell Galaxy G3 User Guide
Galaxy
3-144, 3-144C, 3-520, 3-520C
User Guide
Honeywell Security
Table of Contents
Table of Contents .............................................................................. iii
Introduction ...................................................................................... vii
KEYPAD INFORMATION ..................................................................... 1
General ................................................................................................................ 1
Number Keys (0 – 9) ............................................................................................. 1
View Keys (A and B) ............................................................................................ 1
Enter Key (ent) ..................................................................................................... 2
Escape Key (esc) .................................................................................................. 2
Hash Key (#) ......................................................................................................... 2
Star Key (*) ........................................................................................................... 2
Power LED ........................................................................................................... 2
Banner .................................................................................................................. 2
User Codes ........................................................................................................... 2
SETTING THE SYSTEM ...................................................................... 3
Before Setting ...................................................................................................... 3
Entering A Pin - User Type 2.1 - 2.2 .................................................................... 3
Entering A Pin - User Type 2.3 - 3.6 .................................................................... 3
Setting groups ..................................................................................................... 3
Exit time ............................................................................................................... 3
Sounder ................................................................................................................ 4
Zones Open .......................................................................................................... 4
Final Door/Terminator ......................................................................................... 4
System Set ........................................................................................................... 4
Part Setting .......................................................................................................... 4
Cancelling The Setting ....................................................................................... 4
Group Name ......................................................................................................... 4
MAX SETTING OPTIONS .................................................................... 5
Setting with User Cards/Tags/Fobs .................................................................... 5
Dual Focus ........................................................................................................... 5
Keyprox ................................................................................................................ 5
UNSETTING THE SYSTEM ................................................................ 6
Normal Entry ........................................................................................................ 6
Straying From the Entry Route ........................................................................... 6
Slow Entry ............................................................................................................ 6
Cancelling Alarms ............................................................................................... 6
Manager Reset ..................................................................................................... 6
Engineer Reset .................................................................................................... 6
Unsetting with the MAX Cards ............................................................................ 6
iii
MENU OPTIONS ................................................................................. 7
Full Menu ............................................................................................................. 7
Quick Menu .......................................................................................................... 7
Accessing The Menu ........................................................................................... 8
Full Menu ............................................................................................................. 8
Quick Menu .......................................................................................................... 8
Omit Zones (User Type 2.3 and Above) .............................................................. 9
Purpose .......................................................................................................................... 9
Selecting Omit Zones .................................................................................................... 9
Viewing Eligible Zones .................................................................................................. 9
Omitting Zones ............................................................................................................... 9
Setting With Omitted Zones ........................................................................................... 9
Vibration Zones .............................................................................................................. 9
Atm 1/2/3/4 Zones ........................................................................................................ 10
Forced Set (User Type 2.3 and Above) ............................................................. 10
Purpose ........................................................................................................................ 10
Selecting Forced Set .................................................................................................... 10
Non-omittable Zones ................................................................................................... 10
Chime (User Type 2.3 and Above) .................................................................... 11
Purpose ........................................................................................................................ 11
Selecting Chime .......................................................................................................... 11
Chime In Operation ...................................................................................................... 11
Display Zones (User Type 2.4 and Above) ........................................................ 11
Purpose ........................................................................................................................ 11
Selecting Display Zones .............................................................................................. 11
Address ........................................................................................................................ 11
Function ....................................................................................................................... 11
Status ........................................................................................................................... 12
Description ................................................................................................................... 12
Selecting And Viewing ................................................................................................. 12
Escape ......................................................................................................................... 12
Display Log (User Type 2.4 and Above) .......................................................... 12
Purpose ........................................................................................................................ 12
Selecting Display Log .................................................................................................. 12
Events ........................................................................................................................... 12
Selecting a Date ........................................................................................................... 12
Viewing Each Event ...................................................................................................... 12
Additional Information .................................................................................................. 13
Printing ......................................................................................................................... 13
Print (User Type 2.4 and Above) ....................................................................... 13
Purpose ........................................................................................................................ 13
Selecting Print .............................................................................................................. 13
Codes ........................................................................................................................... 13
Zones ........................................................................................................................... 13
Log ............................................................................................................................... 13
All .................................................................................................................................. 13
Help Message .............................................................................................................. 13
iv
Walk Test (User Type 2.5 and Above) ............................................................... 14
Purpose ........................................................................................................................ 14
Selecting Walk Test ...................................................................................................... 14
All Zones ...................................................................................................................... 14
Selected Zones ............................................................................................................ 14
Ending Walk Test ......................................................................................................... 14
Time/Date (User Type 3.6) ................................................................................. 15
Purpose ........................................................................................................................ 15
Selecting Time/Date .................................................................................................... 15
Changing Time ............................................................................................................ 15
Changing Date ............................................................................................................. 15
Advance and Retard ..................................................................................................... 15
Codes (User Type 3.6) ....................................................................................... 16
Purpose ........................................................................................................................ 16
Manager Code ............................................................................................................. 16
Selecting Codes .......................................................................................................... 17
User Codes .................................................................................................................. 17
Modify Pin ..................................................................................................................... 17
Modify Type ................................................................................................................... 18
Modify Name ................................................................................................................ 19
Time Zone .................................................................................................................... 19
Temporary Codes ........................................................................................................ 20
Pin Change .................................................................................................................. 20
Modify Groups .............................................................................................................. 21
Max Number ................................................................................................................. 22
Max Function ................................................................................................................ 23
Max Keypad .................................................................................................................. 23
Forgive Antipassback ................................................................................................... 23
Pin Warning .................................................................................................................. 24
Summer (User Type 3.6) .............................................................................................. 24
AVOIDING FALSE ALARMS ............................................................. 25
ZONE REFERENCE TABLES .......................................................... 26
ALARM AND HELP MESSAGES ...................................................... 27
Alarm In Progress ........................................................................................................ 27
Pa Reset Required ...................................................................................................... 27
Manager Reset Required ............................................................................................ 27
Engineer Reset Required ............................................................................................ 27
No Entries .................................................................................................................... 27
Invalid Selection ........................................................................................................... 27
Invalid Code ................................................................................................................. 27
Technistore Reset ........................................................................................................ 27
No Modules Added ....................................................................................................... 27
INSTALLER DETAILS ....................................................................... 28
v
vi
INTRODUCTION
The Galaxy series 3 alarm system is, in fact, a computer which has been designed using the
latest software and hardware technology.
First and foremost, the Galaxy series 3 meets all your security needs. The engineer will
program and commission the system to your own exacting requirements.
Warning:
There are no user serviceable parts inside. Please refer all servicing to a qualified installer.
vii
KEYPAD INFORMATION
General
The Galaxy Alarm system is controlled by Galaxy Mk7 Full Alpha Liquid Crystal Display
(LCD) keypads. A maximum of 16 keypads may be connected to the Galaxy 3-144 control
panels. A maximum of 32 keypads may be connected to the Galaxy 3-520 control panels.
GALAXY 520 V5.00
08:58 TUE 22 NOV
LCD Display
Number Keys
1
2
3
A
4
5
6
B
7
8
9
ent
Enter Key
*
0
#
esc
Escape Key
View keys
Star Key
Hash Key
Power LED
Number Keys (0 – 9)
These keys are used to enter the code and to select and modify options.
Before carrying out operations on the system, users must identify themselves with a Personal
Identification Number (PIN). This number is at least a 4 digit number selected from keys
0 - 9.
The number keys are also used where groups are programmed on the system permitting
groups (areas) to be set or unset.
View Keys (A and B)
These keys have been programmed to activate one of the system options. Pressing the A > key
after a valid code has been entered starts the full set routine. Pressing the < B key after a valid
code has been entered starts the part set routine.
Once a system option has been selected, the A > or < B keys can be used to operate as view
keys, stepping forwards (A >) or backwards (< B) through lists of information. Holding down
a view key while viewing an option list, rapidly displays each item in the list, permitting quick
access to the information.
1
Enter Key (ent)
The ent key accepts and processes entered data. Valid actions are performed and the next
option is accessed.
Escape Key (esc)
The esc key aborts the current option to return to the previous option level. Any option
modification made prior to the option being aborted is erased. Successive pressing of the esc
key returns the user to the start display (known as the BANNER).
The esc key also aborts the setting routine if pressed during the exit time.
Hash Key (#)
The # key is used to display additional choices for certain options, e.g. ADVANCE/RETARD
the time in the Time/Date option.
This key is also used as the user duress key (by pressing twice following a valid code
entry).
Star Key (*)
The * key is used to provide additional features for certain options, e.g. printing the event log
or deleting entries.
Power LED
The green power LED remains lit whenever the keypad is connected to a mains power
supply. A mains power failure is indicated by the LED flashing slowly. The LED flashes
rapidly if the battery voltage falls below the minimum threshold or if one of the fuses on the
control panel PCB blows.
Banner
The banner is the display shown on the keypad, e.g. Galaxy 520 V5.00 (with the time and
date on the bottom line). This is shown at all times when the system is unset, unless the menu
is being accessed or an alarm or help message is on the display. The banner can be changed
by the engineer. In the set condition the banner is normally blank.
User Codes
The user code is a unique PIN (Personal Identification Number) of at least 5 digits in length.
The PIN identifies the user to the Galaxy Alarm panel and allows operation of the system.
2
SETTING THE SYSTEM
Code + A
Code + ent
TIMED SET
120
Before Setting
Before setting the system ensure all doors and windows are secured
and areas protected by movement detectors are free from obstruction.
Entering A Pin - User Type 2.1 - 2.2
As each digit is entered the keypad responds with a bleep and displays
a *. When all the digits are entered, press the ent or A > key to start the
setting routine.
Entering A Pin - User Type 2.3 - 3.6
As each digit is entered the keypad responds with a bleep and displays
a *. When all the digits are entered press the A > key to start the setting
routine.
Code + A
Setting groups
SET
Groups
A12345678
UUU-----
1
SET
Groups
A12345678
SUU-----
TIMED SET
120
Code + A
A12345678
USS-----
A Key
SET
Groups
R = Ready (Groups is unset, and all zones are closed)
F = Faulted (Group is unset, and at least one zone is open)
S = Set (Group is set)
ent
SET
Groups
Where group choice has been assigned to the PIN, select which groups
have to set as part of the setting routine. The set status of each group is
displayed on the keypad screen. Possible status options are :-
B12345678
USS-----
L = Lockout (Group is locked out, and cannot be unset)
Select which groups have to be to set by entering the number of the
group. For example, to set groups 2 and 3 press keys 2 and 3 . The
display changes to indicate the groups selected for setting. Pressing
the ent key starts the setting routine for the specified groups.
The Galaxy 3-520 has more than 8 groups. If the user has group
choice, the available groups will be displayed at the keypad following a valid code + A >. The groups will be displayed showing A1 to
A8. Use both A > and < B keys to scroll to the various sets of
groups. If the user does not have group choice, entering the PIN and
A > will cause all groups assigned to the user to set.
Exit time
ent
TIMED SET
60
If all the system zones are closed when the setting routine is started,
the display indicates the remaining time, in seconds, to vacate the
premises. Exit the building using the agreed route.
3
Sounder
During the setting period the sounder emits a continuous tone if all of
the zones are closed. If a zone is opened during the setting period, the
sounder begins to pulse. The sounder also pulses during the last 25%
of the setting time to indicate time running short.
Zones Open
The exit time will reset should any zones be open or opened during
setting. The display will indicate the number of zones open and invite
viewing. Closing the zones will restart the exit time. An alarm will be
generated if setting is not completed before the Fail to Set period expires. (Fail to Set; programmed by engineer).
3 zones open
[<] [>] to view
Note:
Before closing the open zone, press esc to abort the setting
routine. The ESC TO ABORT message will flash as a
reminder.
Final Door/Terminator
The setting procedure can be manually completed by either closing the
FINAL door or by pressing the TERMINATOR button.
System Set
When time has expired or a manual termination is made, the system
waits four seconds before setting. The sounders emit two long tones to
confirm that the system is set. The keypad briefly displays the message
SYSTEM SET, before returning to the banner.
Part Setting
PIN + B
PART SET
120
To Part Set the system press the < B key after the PIN. Only the zones
which have the PART attribute enabled are set. All other setting features
are the same.
Cancelling The Setting
The setting routine can be aborted by pressing the esc key before the
system sets.
SET
Groups
*
A12345678
RRRRRRRR
+#
A1 OFFICE AREA R
[<] [>] #=CHANGE
Group Name
Press * and # keys simultaneously when groups are displayed on the
keypad (when setting for example), will display the name of the
group . The group name should be programmed by the installation
engineer. Press the * and # keys to return to the group display.
4
MAX SETTING OPTIONS
Setting with User Cards/Tags/Fobs
MAX user cards/tags/fobs can be used to set the system. This is done by assigning a MAX
user card (tag or fob) with one of the setting options. When the MAX card is held against a
MAX module for five seconds, the MAX function is activated. For example, if the MAX
function assigned is 13 = Part Set, then activating the card held function results in the system
being part set.
If a user is assigned group choice, then a keypad will have to be accessed to select the group
for setting after swiping the card.
Dual Focus
If a # is assigned to a particular users pin and their max card number, then the user will have
dual focus operation. This means that they will have to enter their pin first, before setting with
the max card and vice versa.
Keyprox
A keyprox is a keypad that has a card reader built in. They are normally installed on systems
where dual focus setting and unsetting are used. Keyproxes are used as a keypad and MAX as
detailed above, but the card is held against the lower right corner of the keypad as shown in
the following diagram:
GALAXY 520 V5.00
08:58 TUE 22 NOV
1
2
3
A
4
5
6
B
7
8
9
ent
*
0
#
esc
5
UNSETTING THE SYSTEM
Normal Entry
PIN + ent
Galaxy 520 V5.00
15.49 MON 18 Nov
Unsetting starts immediately when the FINAL door is opened or an
ENTRY zone is activated. The sounder pulses slowly and the user must
go directly to the keypad and enter a valid PIN, followed by A>, <B or
ent. Users with group choice, will access the UNSET screen following
PIN entry. This permits the user to unset specific groups. To return to
the SET screen press ent.
Straying From the Entry Route
Go directly to the keypad when entering the building. If the user strays
into a protected area and activates a zone, a full alarm will occur. The
police may be called out and the system will have to be reset.
Slow Entry
Enter a valid PIN before the entry time expires. If the entry time expires
before a valid PIN is entered, then a full alarm will occur. The sounder
begins to pulse quickly when 75% of the entry time has elapsed
indicating time is running short.
Cancelling Alarms
PIN + ent
4 ALARMS
[<] [>] to View
CALL MANAGER
RESET REQUIRED
CALL ENGINEER
RESET REQUIRED
To cancel an alarm, enter a valid PIN followed by ent at the keypad.
The keypad displays details of the zone activated. When more than one
zone is activated, details can be viewed using A > or < B. Press ent to
return to the banner. Certain types of alarms, once cancelled, require a
code with the appropriate reset authorisation to be entered. The system
prompts for a valid reset code by displaying Manager Reset Required or Engineer Reset Required on the keypad.
Manager Reset
Entering a manager type PIN followed by ent, resets the system
following an alarm activation.
Engineer Reset
Certain types of alarm require an engineer to visit the site and, after
investigation, reset the system. In such cases, the system cannot be reset
until the engineer reset has been carried out.
Unsetting with the MAX Cards
If any of the groups assigned to the MAX are set, then swiping the
MAX module with a card unsets the groups. Group choice and dual
focus operation, where implemented will apply as per setting instructions.
6
MENU OPTIONS
The Galaxy 3 Series provides various menu options for modifying the functional performance of the system.
There are two menu structures:
Full Menu
Only accessed by authorised users including the master manager code and by the engineer.
Quick Menu
A selection of options from the full menu. The quick menu is the default menu access for all
user codes (type 2.3 and above) except the master manager and engineer.
Full Menu
User Type
Quick Menu
Type 2.3
Type 2.4
Type 2.5
Type 3.6
2.3
0 = Omit
Zones
10 = Setting
20 = Display
30 = Test
40 = Modify
2.3
1 = Forced
S et
11 = Omit
Zones
21 = Display
Zones
31 = Walk Test
41 = Time/Date
2.4
2 = Chime
12 = Timed Set
22 = Display
Log
32 = Outputs
42 = Codes
2.4
3 = Display
Zones
13 = Part Set
23 = System
43 = Summer
2.4
4 = Display
Log
14 = Forced
Set
24 = Print
44 = Trace
2.4
5 = Print
15 = Chime
25 = Access
Doors
45 = Timer
Control
2.5
6 = Walk
Test
16 = Instant Set
46 = Group
Omit
3.6
7=
Time/Date
17 = Instant
Part
47 = Remote
Access
3.6
8 = C o d es
18 = Home Set
48 = Access
Authorisation
3.6
9 = Summer
19 = All set
49 = Datelock
Table 1. Menu Options
7
Accessing The Menu
To access the menu enter a valid code and press the ent key. The Full Menu or Quick Menu
is accessed, depending on the user type.
Note: 1. If the user does not have group choice, all groups assigned to the user code must
be unset.
2. If the user has group choice, only the group that the FINAL or ENTRY zone is
assigned to in unset.
3. If there are no groups, then the system must be unset.
Full Menu
The Full Menu has a hierarchy of four structures contained within it. Each structure is
accessible by an increased user code type.
Quick Menu
The Quick Menu offers users type 2.3 and above a selection of up to 10 options, numbered 0
– 9. The required option is selected by entering the option number (0 – 9) or by using the A
> or < B keys to display each option.
The menu options (as with all Galaxy lists) are circular, therefore menu option 9 is followed
by menu option 0.
The following Quick Menu options are the factory default settings. Each option is described
in the following pages.
8
Omit Zones (User Type 2.3 and Above)
Purpose
This option allows the user to omit zones before setting the system.
Zones must be eligible for omission otherwise they will not be displayed.
PIN + ent
Note:
0 = OMIT ZONES
[ent] to select
ent
1003 A1 INTRUDER
#=OMIT ENT=SET
>A
1004 SECURITY
#=OMIT ENT=SET
#
1004 SECURITY
OMITTED ENT=SET
Selecting Omit Zones
Enter the QUICK MENU. The 0=OMIT ZONES option is displayed.
Press the ent key to select this option.
Viewing Eligible Zones
When the Omit Zones option is selected the first zone eligible for
omission is displayed. The eligible zones can be viewed by pressing
the A> or <B keys. The zones eligible for omission can be rapidly
viewed by holding down either of these keys.
Omitting Zones
Once the zone to be omitted is shown on the display, press the # key.
The display indicates that the zone is omitted. A> and <B keys can
then be used to select other zones to be omitted using the same method.
Note:
ent
1 OMITTED 120
esc
ZONES OMITTED
14:35 TUE 17 DEC
Zones remain omitted for one set period only.
A zone is omitted from the system as soon as the # key is
pressed. The system does not have to be set.
Setting With Omitted Zones
When the list of omitted zones is complete the setting routine is started
by pressing the ent key. The system starts to set and the display indicates
how many zones have been omitted. Alternatively the esc key can be
used to return to the menu options. Zones that have been omitted remain
omitted even after using the esc key.
Note:
All zones omitted are recorded in the log against the user.
Vibration Zones
If the omitted zone is a vibration zone, then all zones of this type (in
all groups) will be block omitted. The vibration zones remain
omitted until manually reinstated. Unsetting the system does not
reinstate vibration detectors.
9
Atm 1/2/3/4 Zones
ATM zones are omitted by entering one of the ten ATM codes (last 10
users). To select this option enter an ATM code followed by the ent
key. Use the A> key to scroll through the four ATM zone options
(ATM1 to ATM4) and select by pressing the ent key. A preprogrammed
ATM delay time will expire before omitting all ATM zones with the
selected ATM zone type. The zones will be omitted for the duration of
the ATM time-out period and the remaining time in minutes will be
displayed on the initiating keypad. A warning is given ten and five
minutes before the zones are reinstated. The ATM Time-out period
can be extended by entering an ATM code and selecting 1=Reset
Access. To manually reinstate ATM zones, enter an ATM code and
select 2=Abort Access.
ATM PIN + ent
[ent] to Select
1=ATM-1
>A
[ent] to Select
2=ATM-2
ent
DELAY ACCESS
ATM-2 12 mins
ACCESS TIMEOUT
ATM-2 10 mins
ATM PIN + ent
1=RESET ACCESS
2=ABORT ACCESS
1
Forced Set (User Type 2.3 and Above)
Purpose
When enabled, the Forced Set option allows the user to automatically
omit zones, eligible for omission, which are open when the system
setting routine is started. Zones omitted in this way remain omitted for
one set period only.
ATM PIN + ent
0 = OMIT ZONES
[ent] to Select
Selecting Forced Set
Access the QUICK MENU. Press key 1 followed by the ent key. The
display indicates how many zones have been omitted and the number
of seconds left before setting.
1
1 = FORCED SET
[ent] to Select
ent
3 OMITTED
120
Non-omittable Zones
Some open zones may not be eligible for omission from the system. In
this case the display indicates which zones are open and the exit time is
reset. These zones must be closed before setting can continue.
2 zones open
[<] [>] to View
10
Chime (User Type 2.3 and Above)
PIN + ent
0 = OMIT ZONES
[ent] to Select
2
2 = CHIME
[ent] to Select
ent
CHIME MODE
0 = OFF
>A
CHIME MODE
1 = ON
ent
Purpose
The Chime mode is switched on and off by this option. When the
Chime mode is on, any zones that have been programmed by the
engineer for chime will activate momentarily when opened.
Note:
Your system may not require any zones of this type.
Selecting Chime
Enter the QUICK MENU. Press key 2 followed by the ent key. The
display shows the ON/OFF status of the Chime mode. Press the >A
key to toggle between the states and press the ent key to accept the
selection.
Note:
Keys 1 AND 0 can also be used to select ON and OFF
respectively.
Chime In Operation
When switched ON, the Chime mode remains active until switched
OFF again. Zones that have been programmed with the chime attribute
by the engineer continue to chime when they are activated.
Note:
The Chime mode is suspended while the system is set or
during an alarm.
Display Zones (User Type 2.4 and Above)
PIN + ent
0 = OMIT ZONES
[ent] to Select
3
3 = DISPLAY ZONES
[ent] to Select
ent
1001 INTRUDER
COMPUTER ROOM
Purpose
This menu option provides the user with a method of accessing the
Display Zones mode and checking each zone for its description and
current status.
Selecting Display Zones
Enter the QUICK MENU. Press key 3 followed by the ent key. Details of the first zone (1001) are displayed.
Address
The zone address provides a unique four digit address number used for
identification and selection, e.g. 1026 - line 1, RIO 02, zone 6.
Function
The zone function is displayed and identifies the operation of the zone,
e.g. INTRUDER, FIRE.
11
Status
The current status of the zone is displayed as circuit information, e.g.
Open or Closed. This information alternates with function information.
Description
The zone description, if programmed, is displayed on the bottom line
of the display. The descriptor is assembled from alpha-numeric text
and describes the zone in detail, e.g. West Office Door.
1001 INTRUDER
COMPUTER ROOM
2+1
1021 SECURITY
CASHIER DOOR
esc
Selecting And Viewing
Selecting the Display Zones option displays the first zone address
available on the system. Other zones can be viewed sequentially by
using the >A or <B keys. Zones can also be displayed by entering the
address of the zone: enter the line, RIO and zone number (4 digits).
Press the # key to display the circuit resistance in ohms and RIO voltage
(if hardwired).
Escape
The esc key aborts the option and returns to the option menu.
Display Log (User Type 2.4 and Above)
PIN + ent
0 = OMIT ZONES
[ent] to Select
4
4 = DISPLAY LOG
[ent] to Select
ent
LOG
Groups
A12345678
NN-----1+2
LOG
Groups
A12345678
YY-----ent
08:53 TUE 22 NOV
AC FAIL-RIO108
B (hold)
MON 21 NOV 1999
MON 20 NOV 1999
Purpose
The Display Log option provides the user with a means of viewing the
system history. Events are recorded in detail and stored in the nonvolatile memory.
Selecting Display Log
Enter the QUICK MENU. Press key 4 followed by the ent key.
Details of the most recent event to be logged are displayed.
Events
The events available for display include details of setting, unsetting
and alarms. Each event is timed and date stamped.
Selecting a Date
Hold down one of the view keys, the dates held in the log are rapidly
stepped through. The A> key moves forward through the dates and the
<B moves backwards. Stopping at the required date reveals the first
event for that date.
Viewing Each Event
The entire events of any one date can be viewed by progressively
stepping through the events using the A> and <B view keys.
*
If the user has group choice enabled, the groups will display. Events for
each group can be displayed by entering the group number.
release B
12
release <B
16:31 SUN 20 NOV
FULL SET USR 98
*
#
16:31 SUN 20 NOV
KOO L6 A1------esc
Additional Information
The # key can be used to reveal additional information on some types
of events. This information is displayed on the bottom line. The
information includes details such as zone descriptors, user types and
which keypad was used.
Printing
If a serial printer is connected to the system, a system history can be
printed by pressing the * key. The system will print from the event on
display until the most recent event.
Print
Print (User Type 2.4 and Above)
PIN + ent
0 = OMIT ZONES
[ent] to Select
5
5 = PRINT
[ent] to Select
ent
1=CODES 2=ZONES
3=LOG 4=ALL
Purpose
The Print option gives the user the opportunity to get a hard copy
print-out of the system details. This option requires a serial printer to
be connected to the system.
Selecting Print
Enter the QUICK MENU. Press key 5 followed by the ent key. The
system print options are displayed. Pressing the esc key aborts the
PRINT option.
Codes
Press key 1 to start the print-out of all the codes, giving the user
number, name, level and length of code.
1
PRINTING CODES
ESC to abort
2
PRINTING ZONES
ESC to abort
3
PRINTING LOG
ESC to abort
4
PRINTING ALL
ESC to abort
PRINTER off-line
ESC to abort
Zones
Select the Zones option to print-out the details of each zone in the
system. The zone address, function, and descriptor is printed. Press
key 2 to select this option.
Log
The entire LOG can be printed out by selecting key 3. The print-out
consists of up to 1000 events depending on panel type, and details
the time and date of setting, unsetting and alarms.
All
All the options (CODES , ZONES, and LOG) can be printed out by
selecting the ALL option. Pressing key 4 delivers a print-out
starting with user codes.
Help Message
If a print-out is started without a printer being connected and on-line,
the display indicates that the printer is off-line.
13
Walk Test (User Type 2.5 and Above)
PIN + ent
0 = OMIT ZONES
[ent] to Select
6
6 = Walk Test
ent to select
ent
1=TEST ALL ZONES
2=SELECTED ZONES
1
WALK TEST ACTIVE
ESC to abort
Purpose
The Walk Test option provides a method of testing the zones to
ensure that they are operating correctly. There are two options
available:
1. All zones can be tested
2. Selected zones can be tested
In both cases the sounder indicates an open zone. The test is recorded in
the log. Wire-free zones also show the received signal strength as a
percentage
Selecting Walk Test
Enter the QUICK MENU. Press the key 6 followed by the ent key.
When Walk Test is selected, Test All Zones or Selected Zones
displays.
All Zones
Choosing All Zones (press key 1) starts the test immediately. No
selection is necessary as all valid zones are included in the test. The
sounder operates whenever a zone is opened and stops when all zones
are closed.
NO ENTRIES
Note:
2
1001 FINAL
#=TEST ENT=START
>A
1002 EXIT
#=TEST ENT=START
Selected Zones
Choosing the Selected Zones option by pressing key 2 displays the
first zone on the system. Each zone is displayed in turn by using the >A
or <B keys. When the zone to be included in the test is displayed, press
the # key. Other zones can be included in the test in the same manner.
When all of the required zones have been selected, press the ent key to
start the Walk Test.
Note:
#
1002 EXIT
TEST ENT=START
The Test All Zones option only tests zones which can
be omitted from the system.
The Selected Zones option includes non-omittable
zones.
Ending Walk Test
To abort the walk test option press the esc key, otherwise the walk test
option remains active for 20 minutes after the last key press.
ent
14
Time/Date (User Type 3.6)
PIN + ent
0 = OMIT ZONES
[ent] to Select
Selecting Time/Date
Enter the QUICK MENU. Press key 7 followed by the ent key. Once
the Time/Date option has been selected, the time or date can be selected by pressing the A> or <B key.
7
7 = TIME/DATE
[ent] to Select
ent
15:25 14/12/1999
A=TIME B=DATE
A>
Purpose
The Time/Date option allows the user to modify both the time (hours/
minutes) and the date (day/month/year).
<B
NEW TIME
--:-HH:MM
enter time
NEW DATE
--/--/-- DD/MM/YY
enter date
15:25 14/12/1999
A=TIME B=Date
#
Changing Time
To change the time press the A> key. The display prompts for a New
Time in hours and minutes (HH:MM). When the new time is entered,
the display immediately returns to the time or date selection screen.
The system does not accept invalid times (greater than 23 hours, greater
than 59 minutes). Pressing the esc key aborts the entry.
Changing Date
To change the date press the < B The display prompts for a New Date
in days, months and years (DD/MM/YY). When the new date is entered, the display momentarily shows the day of the week, before returning to the time or date selection screen. The system does not accept invalid dates (e.g. 32/13/99). Pressing the esc key aborts the entry.
Advance and Retard
It is possible to advance and retard the time to compensate for any
variations in clock speed. Press the # key when in the time/date mode
to select the clock speed adjustment. The range is 0 to 120 seconds per
week. Pressing the * key will retard the time.
Adjustment/week
010 (0-120) secs
*
(press the
* key to retard time)
15
Codes (User Type 3.6)
PIN + ent
0 = OMIT ZONES
[ent] to Select
8
8 = CODES
[ent] to Select
ent
CODES
1 = User Codes
>A
CODES
2 = PIN Warning
Purpose
The Codes menu option enables the managers, (user type 3.6), to
assign, modify and delete the codes that allow users to operate and
access the system. The codes option is divided into two sub–menus:
1. User Codes
Sub divided into 10 menus (depending on whether the group and
MAX Mode options are enabled) that determine all of the access
information for users with Personal Identification Numbers (PINs).
This menu also assigns MAX details to user numbers.
2. Pin Warning
This option determines the warning period given to users prior to
the programmed Pin Change date.
Note: The valid period for Pin Change codes is programmed by
the installation engineer.
Manager Code
The manager code is authorised to:
• Program the USER CODES option for each of the user codes.
• Allocate other codes to manager type 3.6.
• Modify the manager PIN (the manager PIN cannot be deleted)
• Assign the MAX features to the code.
The manager code defaults to group choice when groups are enabled. The manager is able to toggle the group choice option on and
off (using the * key) as required.
The manager code defaults to accessing the quick menu.
Note:
The MAX is the Proximity Access Reader which can be
connected to the Galaxy system. This also refers to the
MAX3, the enhanced version of the MAX.
16
PIN + ent
0 = OMIT ZONES
[ent] to Select
8
8 = CODES
[ent] to Select
ent
CODES
1 = User Codes
ent
001 USER
L3
ent
[ent] to Select
1 = Modify PIN
Selecting Codes
Enter the QUICK MENU. Press key 8 followed by the ent key.
User Codes
When the Codes option has been selected, press key 1 to access User
Codes. Display each of the user numbers using key A>. Each user
number offers options for PIN, level, name and where applicable time
zones and groups. When the user number to be modified is displayed,
press the ent key to access the Modify Pin option.
Modify Pin
The Modify Pin option allows a pin to be assigned to a user or an
existing PIN to be modified. The PIN must be a four, five or six digit
number that is unique to the system. If a duplicate PIN is assigned,
the message Duplicate Entry is displayed. As each digit is entered
it appears on the bottom line of the display. Pressing the * key erases
the last digit displayed. Continued pressing of the *key will erase all
of the digits. When the correct PIN has been assigned press the ent
key to accept the programming and return to the previous menu level.
ent
001 PIN
> 5678
ent
001 PIN
> #5678
Indicates
Dual Code
001 USER
L3
When a PIN has been assigned to a user number, a solid box („) is
displayed on the line of the user number details screen.
• Deleting a Pin
Existing PIN entries can be completely erased using the * key
instead of a digit entry. When there is no PIN assigned to a user
number a hollow square (†) is displayed in the top line of the
users details screen.
• Assigning Dual Codes
To program a user code as a Dual Code press the # key while
theModify PIN option is selected. The # displays at the start of
the assigned user PIN e.g. #5678. When a PIN has been assigned as a dual code two solid boxes („„) are displayed in the
top line of the users details screen.
• Dual Codes Operation
Entry of a single dual code cannot gain access to the menu, set
or unset the system. The message NO ACCESS – ADDITIONAL CODE is displayed. A second dual code must be
entered within 60 seconds to access the menu, set or unset the
system. Dual codes can be of different levels. The highest level
code entered determines the access level to the system.
A single entry of a dual code, without a second dual code entry
within 60 seconds, results in an Illegal Code record in the
EventLog. All outputs programmed as Illegal Code are activated.
17
PIN + ent
0 = OMIT ZONES
[ent] to Select
8
8 = CODES
[ent] to Select
ent
CODES
1 = User Codes
ent
001 USER
L3
Modify Type
Each user is assigned an access type which determines the menu
options available to the user (see p.7, Table 1. Menu Options). On
selecting this option, enter the type to be assigned to the user and
press the ent key to accept the programming and return to the previous
menu level. See Table 2. User Access Levels, for access availability.
EN50131-1
L evel
Type
1
1.0†
Guard
Entered into event memory – no other option
2
2.1†
Cleaner
Can only set the system
2
2.2†
Caretaker
Can only set and unset the system
2
2.3
Users
Menu options 11 - 19
2
2.4
Users
Menu options 11 - 29
2
2.5
Users
Menu options 11 - 39
2
3.6‡
Manager
Menu options 11 - 49
3
3.7‡
Engineer
Menu options 11 - 71
3
3.8‡
Remote
Menu options 11 - 71
†
‡
ent
Access Availability
No access to menu functions
The manager, engineer and remote codes (the last three codes
on the system) have fixed types which cannot be reprogrammed.
Table 2. User Access Levels
[ent] to Select
1 = Modify PIN
>A
[ent] to Select
2 = Modify Level
ent
• Duress Code
If the # key is pressed while Modify Level is accessed, then the
current code is assigned as a Duress Code. There is no limit to the
number of codes which can be assigned as Duress. Entering a duress
code at any time activates outputs programmed as Duress or PA.
001 Level
>_3
Any valid PIN followed by # # ent (the ent key can be replaced by
either the A> or <B key) can be used as a Duress Code.
ent
18
PIN + ent
0 = OMIT ZONES
[ent] to Select
8
8 = CODES
[ent] to Select
ent
CODES
1 = User Codes
ent
001 USER
L3
A1_______
ent
[ent] to Select
3 = Modify PIN
3
[ent] to Select
3 = Modify Name
>A
ent
001 NAME USER_
EFG HIJKLMNØö0 P
ent
• Quick Menu
All user codes default to the quick menu. This menu is made up of
a selection of ten options (0 – 9) from the menu options 11 – 49.
The user code type controls access to the quick menu. Any user
can be upgraded from the quick menu to the full menu by assigning
a * to the user while the Modify Level option is accessed. Therefore
a user with a type *2.5 would have access to the full menu from
options 11 – 32. No code can access both menus.
Note:
The master manager code defaults to the full menu.
Modify Name
This allows a name to be assigned to the user (maximum 6 characters).
Each of the user codes default to the name USER and the manager
defaults to MGR. The manager name cannot be changed. On selecting
the Modify Name option, a section of the alpha-numeric that can be
assigned to the user name is displayed on the bottom line of the keypad;
the cursor flashes on the letter L. Press * to erase the letters of the
default or previous name. When the previous name has been erased,
use the A> or <B keys to move the cursor to the first letter of the name
and press the ent key. The selected character appears on the top line,
continue this process until the name is completed. The # key toggles
between upper and lower case characters and the system library. Press
esc to save the name and exit.
Time Zone
Managers can allocate time zones to user PINs when TIMERS have
been programmed by the engineer. Time zones are used to disable the
user PIN during the times (ON to OFF) programmed in TIMER A
and B.
When 4 = TIME ZONE displays, press the ent key . Using the A> key
select the time zones option to be allocated to the PIN. The following
time zones options are available:
[ent] to Select
4 = Time Zone
ent
[ent] to Select
0 = OFF
Use the A key
to step through
the four time
zone options.
ent
0=OFF
1=TIMER A
2=TIMER B
3=TIMER A+B
The times assigned to Timer A and Timer B can be viewed using
option 45 Timer Control. No access will be granted if a code, assigned
to 1=Timer A, 2=Timer B or 3= Timer A+B is entered out with the
assigned times, an Illegal Code event is recorded in the log and any
outputs programmed as Illegal Code are activated.
19
Temporary Codes
Temporary Codes allow a PIN to be temporarily allocated to a user.
On selecting this option, enter the number of days (0 – 99) that the
code is to remain active. The default setting of 0 indicates that the
code is permanent. A temporary code expires and is removed from the
codes list at midnight after the assigned number of days. A code that
has been assigned as a Temporary Code is indicated on the user code
display by a ^ between the user number and the user name, e.g. 001^
USER.
PIN + ent
0 = OMIT ZONES
[ent] to Select
8
8 = CODES
[ent] to Select
ent
Note:
CODES
1 = User Codes
The manager, rngineer or remote codes cannot be as
signed as a Temporary Code.
Pin Change
To program a user code as a PIN Change code, select the Temporary
Codes option and press the * key instead of a number of days for a
temporary code. Press the ent key to accept the programming and return
to the previous menu level. A code assigned as a PIN Change code is
indicated on the user code display by a * between the user number and
the user name, e.g. 001 * USER. If a user is assigned the PIN Change
feature in the Temporary Code option, the user must assign a new
PIN after a predetermined period of time otherwise the PIN expires
and is no longer operational. A notification (1 – 28 days) that the PIN
requires to be changed can be assigned using the PIN Warning option.
This prompts the user to assign a new code whenever the expiring
code is entered during the PIN Warning period (except during system
unsetting). The new PIN must be four to six digits long and must be
different from any current PIN. The new PIN must be re-entered and if
confirmed, returns the user to the banner. If the esc key is pressed or
the new PIN entered is invalid, the user may continue to use the panel
as normal. The next PIN entry will prompt the PIN change.
ent
001 USER
L3
ent
[ent] to Select
1 = Modify PIN
5
[ent] to Select
5 = Temp Code
ent
Temp Code
00 (0-99) days
Note:
2+5
Temp Code
25 (0-99) days
If the user has not entered a new PIN by the end of the
PIN Warning period, then the PIN is erased on the next
unsetting of the system.
ent
*
Temp Code
(0-99) days
PIN Change Code
ent
20
PIN + ent
0 = OMIT ZONES
[ent] to Select
8
8 = CODES
[ent] to Select
ent
CODES
1 = User Codes
ent
001 USER
L3 A ________
Modify Groups
This option determines the system groups that the user has access to
and operational control over. The Modify Groups option is only
available when the Group Mode has been enabled by the engineer.
The system defaults to groups disabled.
Groups allocated to the user are displayed when the Modify Groups
option is selected. All users default to Group 1. Pressing the group
number toggles the group assigned to the user. e.g. Pressing 2 and 3
assigns Groups 2 and 3 to the user. Pressing 1 (while group 1 is already
assigned) removes group 1 from the user code. To assign group choice
to the user, press the * key. When the required groups have been assigned to the user, press the ent key to accept the programming and
return to the previous menu level.
• Galaxy 520
The Galaxy 520 has 32 groups. The groups are displayed on the
keypad in blocks of eight groups which are labelled A, B, C and
D:
ent
[ent] to Select
1 = Modify PIN
Use A> or <B keys to move between the group blocks. Press
keys 1 – 8 to assign the groups in each block to the user.
6
[ent] to Select
6 = Modify Groups
ent
Groups A 1_______
>A 1_______
>A
Group Block
Physical Groups
A1-8
1-8
B1-8
9-16
C1-8
17-24
D1-8
25-32
Groups B 1_______
>B 1_______
1+2+3
Groups B 1_______
>B _23_____
• Single Groups
A user can be assigned to any single group. In this case a user
can only access, set and unset the single group.
• Multiple Groups
Users can be allocated to more than one group in which case
access and operation are collective. The user cannot choose to
operate on a single or combination of the assigned groups.
21
*
Groups B 1_______
>B Ú23_____
ent
• Group Choice
Users can be allocated to more than one group, but also have the
choice of which of the allocated groups to view, set or unset.
Pressing * key while assigning groups to the user assigns the
group choice feature.
Notes:
1.The manager has fixed access to all system groups. This
cannot be reprogrammed.
2.The manager is assigned group choice by default, but the
feature can be removed.
3.Users authorised to access the Codes option can only assign
groups that have been assigned to their user code. A user
who does not have access to group 4, cannot assign group 4
to another user code.
PIN + ent
0 = OMIT ZONES
[ent] to Select
8
8 = CODES
[ent] to Select
ent
CODES
1 = User Codes
ent
001 USER
L3 A ________
Max Number
Each MAX card/tag/fob has a unique 10 digit number laser etched onto
it. A MAX card/tag/fob is assigned to a user by entering this number in
the Max No option. The number identifies the MAX card/tag/fob to
the system and references it to the user it has been assigned to.
1. Enter the unique 10 digit number which is laser etched onto the
MAX card or enter the unique RF keyfob button identifier generated
by the RF RIO or press the A and 1 keys simultaneously of the
KeyProx and present the card/fob to the KeyProx reader
within 5 seconds. The decrypted number in the card will be self
learned onto the Galaxy panel and is displayed on the KeyProx..
2. Press the ent key to save the programming and return to the
previous menu.
ent
[ent] to Select
1 = Modify PIN
7
[ent] to Select
7 = MAX No
ent
MAX No
>
Enter new
MAX number
Note:
A MAX number can be assigned to a user code that does not
have a PIN allocated to it. All other options for this user are valid for
the MAX card/tag/fob. It is recommended that MAX numbers should
be assigned to users not requiring a PIN at the Max Users menu option.
When a MAX number has been assigned to a user number, a lower case
(m) is displayed on the top line of the user number details screen.
A # assigned to the max number makes the max function dual focus, ie
it needs the pin entered first. A star * assigned to the max number makes
the card dual access, ie it needs another card to open doors.
ent
22
PIN + ent
0 = OMIT ZONES
[ent] to Select
Max Function
The MAX card can be assigned to a single menu option. The user must
be authorised to access the menu option, either by the user level assigned
or by having the menu option access type changed by the engineer.
8
8 = CODES
[ent] to Select
ent
CODES
1 = User Codes
ent
001 USER
L3 A ________
ent
[ent] to Select
1 = Modify PIN
9
The default option is Not Used. A new option is assigned by scrolling
using the A> or <B keys until the required option is displayed or directly
entering the option number using the keypad digits. Select the function
by pressing the ent key
Max Keypad
The menu option assigned to the MAX card/tag/fob can be limited to
operate on a single keypad. On selecting this option the display shows
**, indicating that a keypad has not been specified. To specify a keypad,
press the # key. The address of the first keypad on the system is
displayed. Use the A> or <B key to select the required keypad and
press the ent key to accept the programming.
8
[ent] to Select
8 = MAX Function
ent
MAX Function
= NOT USED
**
1+2 (A>)
MAX Function
12 = TIMED SET
Note: A black flashing square over the first digit of the keypad
address indicates the address of the keypad currently
being used.
• “Card- Held” Max Operation
The MAX function is activated when the card is held directly in
front of a MAX reader for three seconds. The MAX reader must
be assigned a common group to the MAX user. The keypad
specified in the Max Keypad option displays the assigned MAX
function.
ent
[ent] to Select
9 = MAX Keypad
ent
- KEYPAD
**
# = Enable
#
01 - KEYPAD
# = Disable
Note: If the specified keypad is in use, then the option does not
display. If the MAX function is an “action” type option, e.g.
12 = Timed Set, then the function is carried out.
If no keypad is specified (**), the MAX menu option will operate on
all keypads that share the groups of the MAX user. If there is more
than one keypad, the message Press any key is displayed on all valid
keypads. Press any key to activate the function on that keypad. Press
no key within five seconds and the function automatically activates on
all keypads.
A>
02 - KEYPAD
# = Disable
ent
Forgive Antipassback
When the Timed Antipassback feature is enabled, it will prevent
more than one use of any particular card at a particular reader within
a preset time period. The forgive function is available to clear all or
particular antipassback restrictions in force.
23
Pin Warning
This option determines the number of days notification before the expiry
date of any user codes programmed as PIN Change. During the
notification period, the user is prompted to enter a new code on entry
of the expiring PIN. The default period is 99 days, with a programmable
range of 1 – 99. If a user does not assign a new code by the end of the
PIN Warning period, then the code is erased on the next unsetting of
the system.
PIN + ent
0 = OMIT ZONES
[ent] to Select
8
8 = CODES
[ent] to Select
ent
CODES
1 = User Codes
Note:
>A
The PIN Warning ends on the last day of the month, the
PIN expires on the first day of the following month.
CODES
2 = PIN Warning
ent
PIN Warning
28 (1-28) days
Summer (User Type 3.6)
PIN + ent
On the first day of each year, the British Summer Time (BST) Start
date is set to the last Sunday in March and the End date is set to the last
Sunday in October.
0 = OMIT ZONES
[ent] to Select
9
9 = SUMMER
[ent] to Select
ent
A=START
B=END
26 MAR
29 OCT
A>
B<
NEW DATE
--/--
2+3+0+3
DD/MM
2+7+1+0
23 MAR
29 OCT
A=START
B=END
esc
The operation of the Summer option is as follows: At 01 : 00 hours
on the Start date, the system clock advances to 02 : 00 hours. At 02 :
00 hours on the End date, the system clock goes back to
01 : 00 hours .
Note:The time always changes with reference to GMT.
For example, Italy which is + 1 hour would be:
Last Sunday in March - 02.00 to 03.00
Last Sunday in October - 03.00 to 02.00
The Start and End dates can be reprogrammed by authorised user
codes. Press the A> key to modify the Start date or the <B key to
select the End date. The new date must be a valid four digit number in
the day month format (dd/mm).
26 MAR
27 OCT
A=START
B=END
esc
24
AVOIDING FALSE ALARMS
False alarms are inconvenient and may be costly. Police can withhold response from consistent
offenders.
Here are nine points to help avoid false alarms.
1. Be sure you fully understand how to operate the alarm system. In your absence someone
thoroughly instructed, should be available to operate the system.
2. Before leaving the premises ensure that all doors and windows are securely closed.
3. Where passive infra red or movement detectors are installed make sure the areas are kept
free from all animals or birds. Particular attention should be paid to swinging signs,
fluorescent lights, Christmas decorations, electric fans, heating or ventilating systems.
These should be switched off if possible
4. Always follow the exit/entry route procedure agreed with your alarm installer.
5. Treat the alarm components with care to ensure they are not damaged.
6. Consult your alarm installer about changes to your building and its contents if you think
they may affect the alarm system or its performance.
7. Always report alarm activation to your alarm installer. If necessary, an engineer will be
sent to check the system.
8. If opening or closing times are monitored by a central station be sure you notify them of
any variations from the agreed times or password.
9. The system should be fitted with a stand-by battery (not included) which will operate the
system for a limited period in the event of a mains failure. Please ensure that the mains is
restored as quickly as possible so that the stand-by battery can be recharged.
25
ZONE REFERENCE TABLES
Zone
Function
Description
Chime
Omit
Part
1001
1002
1003
1004
1005
1006
1007
1008
1011
1012
1013
1014
1015
1016
1017
1018
RIO
Zone
Function
Description
Chime
Omit
Part
Function
Description
Chime
Omit
Part
1
2
3
4
5
6
7
8
RIO
Zone
1
2
3
4
5
6
7
8
26
ALARM AND HELP MESSAGES
ALARM IN
PROGRESS
Alarm In Progress
The system is currently in alarm condition and must be cancelled by a valid PIN or
keyswitch operation.
Pa Reset Required
PA
RESET REQUIRED
After a PA (Personal Attack) zone has been activated, the system has to be reset by a
high level code (such as a manager or engineer depending on the reset level setting).
Manager Reset Required
CALL MANAGER
RESET REQUIRED
Following an alarm activation, the system requires to be reset by a manager level code.
This message is displayed when a tamper alarm occurs.
Engineer Reset Required
CALL ENGINEER
RESET REQUIRED
The system has been programmed for engineer reset following an alarm activation. The
engineer must be called to reset the system before the user can set the alarm.Tamper
alarms usually require an engineer to visit the site to check all modules on the system.
No Entries
NO ENTRIES
INVALID
OPTION
Invalid code
This message appears if a user attempts to view or inspect the log and there is nothing in
the log to be viewed or when the omit option is selected and there are no omittable
zones on the system.
Invalid Selection
The option selected or value entered is illegal or out of range.
Invalid Code
The code entered is not a valid code registered in the system memory.
Option Not Available
Option not
available
CALL ALARM CO.
QUOTE CODE XXXXX
This option is provided by the engineer, where it is specifically required. Attempting to
select an option when it has not been provided results in the display of
Technistore Reset
Call the Alarm Monitoring Station and quote the five digit number displayed. Enter the
number quoted by the monitoring station to reset the system.
No Modules Added
NO MODULE ADDED
ESC TO CONTINUE
When exiting Engineer Mode the panel does not detect the change in the number of
modules. Press esc to continue.
27
INSTALLER DETAILS
Name: ----------------------------------------------------------------------------------Address: --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------Telephone: -----------------------------------------------------------------------------Office Hours: --------------------------------------------------------------------------Other Times: --------------------------------------------------------------------------Account No.: ---------------------------------------------------------------------------
28
29
© Copyright Honeywell Security
IU1-0033 Rev B
30
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement