Worcester 25/32 Installation manual

Worcester 25/32 Installation manual
USER INSTRUCTIONS & CUSTOMER CARE GUIDE
EXTERNAL OIL FIRED CONDENSING BOILER
USING BALANCED FLUE SYSTEM
GREENSTAR CAMRAY EXTERNAL &
EXTERNAL SYSTEM12/18, 18/25, 25/32
FOR OPEN VENT AND SEALED CENTRAL HEATING SYSTEMS WITH
DOMESTIC MAINS FED HOT WATER
THE BOILER IS FOR USE WITH
KEROSENE (28 SECOND OIL) ONLY
UK
CONTACT INFORMATION
USER INSTRUCTIONS &
CUSTOMER CARE GUIDE
Worcester, Bosch Group:
PLEASE READ THESE INSTRUCTIONS
CAREFULLY BEFORE OPERATING YOUR
APPLIANCE.
Service call centres:
UK
TEL: 08457 256206
FAX: 08457 757536
SCOTLAND ONLY FAX: 01506 441687
Other enquiries:
TEL:
MAIN RECEPTION: 01905 754624
TECHNICAL:
08705 266241
LITERATURE:
01905 752556
SALES:
01905 752640
WEBSITE:
FAX:
754619
www.worcester-bosch.co.uk
THESE INSTRUCTIONS ARE APPLICABLE
TO THE WORCESTER, BOSCH GROUP
APPLIANCE MODEL(S) STATED ON THE
FRONT COVER OF THIS MANUAL ONLY AND
MUST NOT BE USED WITH ANY OTHER
MAKE OR MODEL OF APPLIANCE.
IF YOU ARE IN ANY DOUBT CONTACT THE
WORCESTER, BOSCH GROUP TECHNICAL
HELPLINE.
PLEASE KEEP THESE INSTRUCTIONS WITH
THE INSTALLATION AND SERVICING
INSTRUCTIONS IN A SAFE PLACE OR WITH
THE APPLIANCE AFTER INSTALLATION OR
SERVICING.
DO NOT INTERFERE WITH ANY SEALED
COMPONENTS.
WATER TREATMENT:
FERNOX 01799 550811
THIS APPLIANCE SHOULD ONLY BE
OPERATED BY RESPONSIBLE ADULTS
WHO HAVE BEEN INSTRUCTED IN AND
UNDERSTAND ITS OPERATION AND ARE
AWARE OF ITS OPERATING CONDITIONS
AND EFFECTS.
www.fernox.com
SENTINEL 0800 389 4670
www.sentinel-solutions.net
FLUE TERMINAL GUARDS:
WORCESTER, BOSCH GROUP
THIS APPLIANCE SHOULD NOT BE
OPERATED BY CHILDREN.
OIL FIRING TECHNICAL ASSOCIATION:
ABBREVIATIONS:
OFTEC 0845 6585080
SEDBUK Seasonal Efficiency for Domestic
Boilers in the United Kingdom.
www.oftec.org
OFTEC Oil Firing Technical Association for the
Petroleum Industry.
USER INSTRUCTIONS &
CUSTOMER CARE GUIDE
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
USING YOUR
APPLIANCE
7
7
7
8
9
ENERGY
SAVING
ENERGY SAVING
TIPS ON ENERGY SAVING
6
10-11
12
13
14
GUARANTEE
YOUR GUARANTEE
GUARANTEE REGISTRATION
15
16
NOTES
MAINTENANCE
MAINTAINING YOUR APPLIANCE
FAULT FINDING
FAULT OR BREAKDOWN
MAINTENANCE
USING YOUR APPLIANCE
CONTROLS
OPERATING THE APPLIANCE
Switching the boiler on/off
Setting the radiator temperature
Controlling central heating
Frost protection
Fault conditions
2
3
4-5
GUARANTEE
INTRODUCTION
SAFETY PRECAUTIONS
EXCELLENCE COMES AS STANDARD
GENERAL INFORMATION
INTRODUCTION
CONTENTS
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
CONTENTS
1
INTRODUCTION
SAFETY PRECAUTIONS
OIL SMELLS, LEAKS OR FUMES FROM THE
APPLIANCE:
! Extinguish any naked flames.
! Switch off the appliance electricity supply.
! Isolate the fuel supply to the boiler.
! Contact installer/service engineer.
HEALTH & SAFETY:
The appliance contains no asbestos and no
substances have been used in the
construction process that contravene the
COSHH Regulations (Control of
Substances Hazardous to Health
Regulations 1988). Where applicable, the
CE mark indicates compliance with relative
EU Directives.
COMBUSTIBLE AND CORROSIVE
MATERIALS:
This appliance is suitable for use with
kerosene only, no other fuel must be
used.
SERVICING:
You must have the system regularly
serviced by a competent, qualified OFTEC
registered engineer using approved spares,
to help maintain the economy, safety and
reliability of the appliance.
The appliance should be serviced once each
year after installation unless the installation
conditions and usage demand more frequent
services.
Although the appliance is serviced externally,
the engineer will require access to the
property to operate the controls.
DO NOT OPERATE THE APPLIANCE WHEN:
Do not store or use any combustible
materials (paper, thinners, paints etc.) inside
or within the vicinity of the appliance.
The combustion air must be kept clear of
chemically aggressive substances which can
corrode the appliance and invalidate any
warranty.
FITTING & MODIFICATIONS:
! The appliance, flue or system is incorrectly
fitted, faulty or damaged.
! The flue terminal outlet or air inlet is
obstructed or damaged.
! There are fumes, fuel leaks or fuel smells
from the fuel supply, appliance or flue system.
! The system is empty, frozen or unpressurised
(sealed systems).
! The condensate pipe is blocked or restricted.
Fitting the appliance and any associated
controls may only be carried out by a
competent engineer in accordance with the
relevant Installation Regulations.
! The appliance clearances are inadequate.
! The air supply is restricted.
Flue systems must not be modified in any
way other than as described in the fitting
instructions.
Any misuse or unauthorised modifications to
the appliance, flue or associated
components and systems will invalidate
the warranty. The manufacturer accepts no
liability arising from any such actions,
excluding statutory rights.
2
EXCELLENCE COMES AS
STANDARD
GREENSTAR CAMRAY EXTERNAL12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
Thank you for purchasing a Greenstar Camray oil
fired condensing boiler from Worcester, Bosch
Group. The company prides itself on
manufacturing boilers to the strictest quality
control standards throughout every stage of
production.
INTRODUCTION
EXCELLENCE COMES AS
STANDARD
Worcester, Bosch Group has led the field in
innovative appliance design and performance for
more than 40 years. This heritage means all
products are of exceptional quality and proven
reliability.
The condensing range, in particular, is extremely
energy efficient, converting more of the fuel
consumed into heat offering you economical
running costs and value for money. It sits in
SEBUK band A, at the top of the energy rated
appliances available.
There is also the assurance of our no-nonsense
parts and labour guarantee - backed up by an
optional servicing and maintenance contract to
keep your boiler operating at peak condition and
efficiency.
To find out more about Worcester, Bosch
Group, use the 'Contact Information' shown on
the inside front cover.
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
EXCELLENCE COMES AS
STANDARD
3
INTRODUCTION
Read these instructions carefully to get the best
from your appliance.
GENERAL INFORMATION
CENTRAL HEATING SYSTEMS:
2. Connect the flexible hose across the two
valves, one leading from the boiler and the other
from the mains supply. The connecting nuts need
only to be hand tight.
During the first few hours of operation of the
central heating system, check that all radiators
are being heated at an even rate.
If the top of a radiator is at a lower temperature
than the bottom then it should be vented by
releasing air through the venting screw at the top
of the radiator. Ask your installer to show you
how this is done. Repeated venting in sealed
systems will reduce the quantity of water in the
system and this must be replenished for safe
and satisfactory operation of the appliance.
When excessive venting or water leaks are found
in the system you must contact a service
engineer to inspect the installation and rectify
any fault.
Only use additives compatible with the appliance
and system. Use of incompatible additives can
cause damage and will invalidate the appliance
guarantee.
Sealed heating systems:
Where the appliance is fitted to a sealed heating
system your installer will inform you of the
minimum and maximum pressure which must be
indicated on the pressure gauge.
Regularly check the pressure is maintained and
contact your installer or maintenance engineer if
there is a noticeable, permanent drop in
pressure. If the system loses pressure it should
be repressurised and the cause of the loss
investigated.
FILLING LOOP: Sealed systems only
Should the sealed system pressure within your
system have dropped to below 0.5 bar (shown
on the pressure gauge located on the fascia of
the External System models) you will need to
increase this to ensure your boiler continues to
run without problems.
Your installer should have informed you where to
find the filling system and instructed you in its use.
Should this have been overlooked you can
increase the pressure by following these
instructions:
1. The boilers integral pressure gauge should be
visible.
4
GENERAL INFORMATION
3. Slowly open both valves ensuring that water
does not leak from either end of the flexible
hose.
4. You will start to hear water passing across the
hose and valves and the grey needle on the
pressure guage will rise.
5. When the needle rises between 1 and 1.5 bar
close both valves, the needle should now remain
fixed.
6. The hose should then be disconnected from
at least one valve, a small amount of water will
emit from the hose, this is normal. If water
continues to issue from the hose the valve has
not been fully closed or is passing. If it is
passing you will need to contact your installer to
resolve the problem.
A filling loop is a set of manually operated valves
and a flexible pipe that allow water to be added
to the system when the valves are opened. This
device must be WRAS approved. To comply with
local water authority by-laws the flexible pipe
should only be connected when topping up the
system and disconnected when not in use.
CONDENSATE:
This is a high efficiency appliance using
condensing technology which will under normal
operation produce a regular discharge of
condensate to drain and at times, give out a
plume of water vapour from the flue terminal.
ROOM THERMOSTAT:
A room thermostat must be fitted to control the
central heating. Refer to instructions supplied
with the room thermostat for information on
siting and setting.
THERMOSTATIC RADIATOR VALVES:
It is recommended that this type of valve is fitted
to all but one of the radiators (or at least those in
the sleeping accommodation). The remaining
radiator, which must be where the room
thermostat is located, should be un-controlled
and must be left open.
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
GENERAL INFORMATION
WARNING:
External equipment operating at 230 Volts
must not be serviced or repaired during
adverse weather conditions.
600mm
INTRODUCTION
INSTALLATION & SERVICING
CLEARANCES
600mm
FRONT
Do not use pressure washers or steam
cleaners on this appliance or cabinet.
2500mm*
FUEL:
This appliance is designed to use kerosene, no
other fuel must be used.
BOILER LOCATION:
WARNING:
BASE
600mm min.
This boiler must not be installed where there
is a potential for excessive ground water
coverage.
2500mm*
To prevent “wetting” it is recommended that the
flue terminal faces away from walls.
Never allow the flue terminal or air inlet to
become obstructed by plants or any other
objects.
Plan
view
85mm
45mm
FRONT
This boiler is only suitable for installing externally
at a suitable location onto a fixed, permanent,
rigid surface capable of supporting the boiler
weight. Wood and tarmac hardstandings are not
recommended.
The boiler must be installed on a flat level
surface to ensure that condensate does not
enter the primary heat exchanger.
600mm
The cabinet is not load bearing, and only
provides weather protection for the boiler inside.
There must be sufficient hard standing and
access around the boiler for servicing.
50mm
Plan
view
2500mm*
FRONT
600mm
10mm
*See installation manual for further details.
The same applies
for right hand flue
installation where
right and left
clearances are
mirrored.
GREENSTAR CAMRAY EXTERNAL 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
GENERAL INFORMATION
5
CONTROLS
B
USING YOUR
APPLIANCE
A
C
2
D
4
0
A
Temperature control.
B
System pressure gauge (External System
models only).
C
Boiler mode indicator.
D
Mode switch.
on
3
1
max
To remove the front panel, undo the screws
using the tool provided on each side of the base
of the front panel. The panel can then be
removed (see illustration below).
service
bar
flue
reset
E
boiler
reset
GREENSTAR CAMRAY EXTERNAL SYSTEM
F
E
Reset button - flue thermostat.
F
Reset button - heating.
G Lockout indcator/reset button (is located
on the burner control box see ‘reset button
locations’ below).
Reset Button Locations
All Models
Remove front panel to access
all reset buttons.
2
3
1
0
4
bar
The Flue Thermostat Reset
Button (E) and Heating
Thermostat Reset Button (F) are
located beneath the boiler
control panel.
The Lockout Reset Indicator/
Button (G) is located on the
burner control box which is
situated on the burner at the
base of the appliance.
6
CONTROLS
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
OPERATING THE APPLIANCE
SWITCHING THE BOILER ON/OFF:
! Check the mode switch is in the ON position
with the indicator illuminated.
! Check the programmer/timer is correct and
it is set to ON.
! Set the room thermostat to the desired
setting.
USING YOUR
APPLIANCE
! To switch on the boiler; turn on the water,
oil and electricity supply to the boiler.
! Open and set thermostatic radiator valves as
required.
! Turn the boiler water temperature control to
the required setting.
CENTRAL HEATING TEMPERATURE CONTROL:
! To switch off the boiler; turn the
programmer/timer to OFF for heating and
hot water. If the appliance is left unused and
exposed to freezing conditions; shut off all
the mains supplies, isolate the boiler and
drain the system and boiler.
on
service
max
flue
reset
boiler
reset
GREENSTAR CAMRAY EXTERNAL
SETTING RADIATOR TEMPERATURE:
! Turn the control clockwise to increase the
radiator water temperature.
! Turn the control anti-clockwise to reduce the
radiator water temperature.
on
service
max
flue
reset
boiler
reset
The minimum and maximum ranges of the
heating control positions are approx. 55°C to
81°C.
GREENSTAR CAMRAY EXTERNAL
CONTROLLING CENTRAL HEATING:
! Set the programmer/timer to the correct time
with the required ON/OFF periods. (Refer to
the user guide supplied with the programmer).
! Turn the room thermostat to the temperature
required.
! Set thermostatic radiator valves to the
required temperature for each room.
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
OPERATING THE
APPLIANCE
7
OPERATING THE APPLIANCE
PRESSURE GAUGE (EXTERNAL SYSTEM):
The pressure gauge indicates the boiler/heating
system water pressure and has two pointers:
USING YOUR
APPLIANCE
2
on
1
3
0
4
service
bar
GREENSTAR CAMRAY EXTERNAL SYSTEM
Red (external) pointer is set manually to indicate
the normal system pressure (1 to 1.5 bar for
sealed systems, 0 to 0.5 bar for open vent
systems).
Grey (internal) pointer shows the actual system
pressure (on sealed systems the pressure will
rise when the boiler/system heats up from cold).
Please check with your installer what type of
system you have.
On sealed systems the red pointer should be set
to the normal operating pressure (1 to 1.5 bar)
and the grey pointer will fluctuate around this
pressure depending on whether the system is
hot or cold. If a sealed system pressure drops
below 1 bar the system should be repressurised
to 1.5 bar and the cause of the drop
investigated. If the pressure rises to more than
2.5 bar please contact your installer for advice.
Regularly check that the pressure is maintained
and contact your maintenance engineer if a
permanent significant drop in pressure regularly
occurs.
On open vent systems the pressure gauge is not
used and the grey pointer will remain at the
bottom of its scale. If the pressure rises to more
than 1 bar please turn off the appliance and
contact your installer for advice.
FROST PROTECTION:
! A frost thermostat is fitted to the
appliance to protect the appliance and
system from the risk of freezing.
! The boiler mode indicator light MUST be
illuminated for the frost protection to
operate.
In the unlikely event that there is no hot
water or heating, remove the front panel
and check for lockout or other fault
conditions.
Check page 9 for fault conditions.
8
OPERATING THE
APPLIANCE
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
1 ACCESSING CONTROLS:
OPERATING THE APPLIANCE
FAULT CONDITIONS:
The Boiler mode and Lockout lights can indicate
some basic fault conditions.
! Undo the screws on the bottom of the
front panel using the tool provided. The
panel can now be removed.
2 NORMAL OPERATION:
2 Normal operation:
on
service
max
flue
reset
boiler
reset
GREENSTAR CAMRAY EXTERNAL
The appliance is in boiler mode, with a demand
for heat from the controls.
3 Both lights on:
3 BOTH LIGHTS ON:
Boiler not firing
on
service
max
flue
reset
Boiler mode light ON
USING YOUR
APPLIANCE
1 Accessing Controls:
boiler
reset
GREENSTAR CAMRAY EXTERNAL
! Check the level in the oil tank.
! Press the Reset button (A). The boiler
should fire.
! If there is no response, wait 2 minutes and
press the Reset Button (A) again.
! If Lockout light stays on, do not attempt
further resets. Contact your Service
Engineer for advice.
A
4 Boiler mode light on, lockout light off:
Boiler not on No heating/hot water
! Press Reset Button (B), press Reset Button
(C) both are below the fascia.
4 BOILER MODE LIGHT ON LOCKOUT LIGHT OFF:
on
service
max
flue
reset
B
boiler
reset
GREENSTAR CAMRAY EXTERNAL
C
! If this fault re-occurs contact your Installer or
Service Engineer.
5 Both lights off:
Boiler not on No heating/hot water
! Ensure there is power supply to the boiler.
! Check the programmer is set to ON and
thermostat is calling for heat.
5 BOTH LIGHTS OFF
on
service
max
flue
reset
! If the boiler remains off, contact your Service
Engineer for advice.
boiler
reset
GREENSTAR CAMRAY EXTERNAL
! Ensure that the Service switch is in Boiler
mode.
! If there is power supply to the boiler contact
your service engineer for advice.
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
OPERATING THE
APPLIANCE
9
TIPS ON ENERGY SAVING
Heating economically:
The boiler is designed to provide a high level of
comfort while keeping oil consumption and the
resulting environmental effect as low as possible.
The temperature control on the boiler should be
set as low as possible while still maintaining a
comfortable room temperature.
ENERGY
SAVING
The temperature of each room can be set
individually using the thermostatic radiator valves
(except the primary room with the room
thermostat).
Roof insulation:
Around 30% of the heat loss from a property is
through the roof. Replace any old insulation with
new insulation, preferably to a minimum
thickness of 200mm.
Window frames:
Single glazed windows, particularly those with
steel frames, can lose a great deal of heat.
Consideration should be given to replacement
with PVCu or wooden framed double glazed
units.
Curtains:
Lined curtains, or heavier full length curtains can
provide excellent insulation. However, always
ensure that the curtains do not drape over
radiators.
Draughts:
Try to ensure that draughts around doors,
windows, letterboxes and keyholes etc., are
reduced by using a suitable draught excluder.
Warning: do not block or seal any air vents
that are installed to ensure the central
heating boiler (or other appliance) operates
safely.
10
TIPS ON ENERGY SAVING
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
TIPS ON ENERGY SAVING
Room thermostats:
Reducing the setting of the room thermostat by
1°C can reduce fuel consumption by up to 10%.
New control systems:
Upgrade your heating control system with the
latest equipment available. The minimum level of
control for a heating system is a
programmer/timer, interlocking room thermostat
and thermostatic radiator valves.
More often than not radiators will be sited
underneath a window, so the warm air from the
radiator heats the colder incoming air from the
window.
ENERGY
SAVING
Radiators:
The performance of the radiator will be affected
if the curtains are allowed to drape over the
radiator or shelves are fitted above it.
The positioning of furniture and tables in front of
the radiator should also be avoided.
It is advisable to manually adjust all radiator
valves every 2-3 months to prevent them from
sticking. It is also important that the plastic tops
of all valves are always in position and not
cracked or damaged to help prevent accidents.
Care should be taken when vacuum cleaning
carpets to avoid damage to valves and pipework.
The heating system and the outputs of the
radiators have been carefully selected by your
installer. The temperature obtainable in any given
room is dependent on all radiators being
operated at the same time. If you decide to turn
off radiators in unused rooms, spare bedrooms
etc., you may experience slightly lower room
temperatures in rooms adjacent to unheated
rooms.
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
TIPS ON ENERGY SAVING
11
MAINTAINING YOUR APPLIANCE
Your new appliance represents a long term
investment in a reliable, high quality product.
In order to realise its maximum working life and
to ensure it continues to operate at peak
efficiency and performance, it is essential that
servicing and maintenance checks are performed
at least once a year by a competent person.
If you would like to know more about servicing
options from Worcester, Bosch Group please
visit www.worcester-bosch.co.uk.
Please tick the appropriate box on your warranty
registration card for further details on the
Worcester, Bosch Group service contract.
In addition to the service contract we are
pleased to offer a one-off annual service or
breakdown call out for your appliance.
MAINTENANCE
When your appliance requires servicing please
contact the Worcester, Bosch Group contact
centre (see inside front cover for details).
Maintenance tips:
Regularly check the oil level in the tank.
Regularly check the system pressure, ask your
installer for guidance.
Do not obstruct the flue outlet or the air inlet.
Do not pressure wash or steam clean the
appliance or its cabinet.
To clean the cabinet wipe down with soapy
water.
12
MAINTAINING YOUR
APPLIANCE
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
Problem
Cause
Remedy
Desired room temperature
is not reached
Thermostatic radiator
valve(s) set too low
Increase thermostatic
radiator valve setting(s)
Room thermostat set too
low
Increase room thermostat
setting
Boiler temperature control
set too low
Increase
temperature control
setting
Air trapped in heating
system
Bleed radiators; if fitted to
a sealed system recharge
heating system
Desired room temperature
exceeded by large amount
Radiators are too hot
Turn down thermostatic
radiator valves / room stat
Temperature rises instead
of falling
Clock is incorrectly set
Check setting
No display or control unit
does not respond
Momentary power failure
Switch off appliance at
master switch, wait a few
seconds then switch on
again
Hot water temperature too
low
Hot water cylinder
temperature set too low
Check setting
Hot water not in timed
period on the programmer
Check programmer
settings
Boiler temperature control
set too low
Check setting
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
FAULT FINDING
MAINTENANCE
FAULT FINDING
13
FAULT OR BREAKDOWN
This appliance is supported in the UK by
Worcester, Bosch Group, part of Bosch
Thermotechnology Ltd.
Specialist factory trained Service Engineers are
available to attend in the unlikely event that a
breakdown occurs on this appliance.
No charge will be made for parts and/or
labour providing:
MAINTENANCE
! An appliance fault is found and the
appliance has been installed within the past
24 months. Reasonable evidence of this
must be supplied on request.
A call-out charge will be made where:
! The appliance has been installed for over 24
months OR
! Our Field Service Engineer finds no fault
with the appliance (see Note) OR
! Evidence cannot be provided that the first
year service inspection has been carried out.
(i.e. an entry in the service interval record
found at the rear of the appliance installation
and servicing manual) OR
! The cause of breakdown is misuse or fault
found with other parts of your
plumbing/heating system, or with equipment
not supplied by Bosch Thermotechnology
Ltd.
circumstances this will be from 1 to 3 working
days (excluding weekends) for priority
breakdown situations (no hot water and/or
heating).
Invoices for attendance and repair work carried
out on this appliance by any third party will not
be accepted.
APPLIANCE DATA LABEL
The data label can be found on the inside of the
left hand panel. To access:
! Unscrew the two screws on the bottom of
the front panel using the tool provided. The
panel can now be removed.
To replace:
! Push the front panel up behind the top
panel, push in and secure the screws with
the tool provided.
Data label
location
Note: NO APPLIANCE FAULT IS FOUND ON
OVER 30% OF ALL SERVICE CALL OUTS.
Please read this guide carefully to gain a good
understanding of the operation of your appliance.
In the case of a suspected fault, refer to the fault
finding section of this guide.
If in doubt contact Worcester, Bosch Group
quoting the boiler serial and model number.
These numbers are printed on a Data Label
which is located as shown opposite. (You can
record this information on the inside back cover
of this manual.)
In the unlikely event of an appliance fault or
breakdown please call the contact centre (see
inside front cover for details). Your service
administrator will arrange for an Engineer to call
with the minimum of delay. Under normal
14
FAULT OR BREAKDOWN
EXTERNAL REGULAR SHOWN
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
YOUR GUARANTEE
This appliance is guaranteed against faulty
materials or workmanship for a period of 24
calendar months (60 months for the primary heat
exchanger) from the date of installation subject
to the following conditions:
! That during the period of this guarantee any
components of the unit which are proved to
be faulty or defective in manufacture will be
exchanged or repaired free of material
charges and free of labour charges if repaired
directly by Bosch Thermotechnology Ltd.
Please be aware that invoices for
attendance and repair of this appliance
by third parties will not be accepted for
payment by Bosch Thermotechnology Ltd.
! That any product or part thereof returned for
servicing under the guarantee must be
accompanied by a claim stating the Model,
Serial Number and Date of Installation.
! That Bosch Thermotechnology Ltd will not
accept responsibility for damage caused by
faulty installation, neglect, misuse or
accidental damage and non-observance of
the instructions contained in the Installation
and Users Instructions leaflets.
GUARANTEE
! That the householder may be asked to
prove, when requested, the date of
installation, that the appliance was correctly
commissioned and, where appropriate, that
the 12 month service inspection has been
carried out to the satisfaction of Bosch
Thermotechnology Ltd, when requested.
The guarantee card must then be returned
within 30 days of installation.
! That the appliance has been used only for
normal domestic purposes, for which it was
designed.
! That this guarantee applies only to
equipment purchased and used in mainland
Great Britain.
This guarantee is given in addition to all your
normal statutory rights.
Worcester, Bosch Group is a trading name of
Bosch Thermotechnology Ltd.
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
YOUR GUARANTEE
15
GUARANTEE REGISTRATION
You should complete and return the postpaid
Guarantee Registration Card within 30 days of
installation.
Returning your card will register you as the
owner of your new appliance and will assist us in
maintaining an effective and efficient customer
service by establishing a reference and
permanent record for your boiler.
This does not affect your statutory rights.
GUARANTEE
For your own record:
Model
Serial No.
(See identity label inside appliance casing)
Type / size
Date of installation
Installer details
16
GUARANTEE
REGISTRATION
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
NOTES
NOTES
GREENSTAR CAMRAY EXTERNAL & EXTERNAL SYSTEM 12/18 - 18/25 - 25/32
8 716 115 668a (05.09)
NOTES
17
Dedicated to heating comfort
Worcester, Bosch Group
Cotswold Way, Warndon, Worcester WR4 9SW.
Tel. 01905 754624 Fax. 01905 754619
worcester-bosch.co.uk
Worcester, Bosch Group is a brand name of Bosch Thermotechnology Ltd.
8 716 115 668a (05.2009)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement